Add support for newest Marvell chips.
The Yukon FE plus chip is found in some not yet released laptops.
Tested on hardware evaluation boards.
This version of the patch is for 2.6.23. It supersedes
the two previous patches that are sitting in netdev-2.6 (upstream branch).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should cause no functional changes in driver behaviour.
There are (too) many revisions of the Yukon 2 chip now. Instead of
adding more conditionals based on chip revision; rerganize into a
set of feature flags so adding new versions is less problematic.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The length check for truncated frames was not correctly handling
the case where VLAN acceleration had already read the tag.
Also, the Yukon EX has some features that use high bit of status
as security tag.
Signed-off-by: Pierre-Yves Ritschard <pyr@spootnik.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes the extra timer overhead that people were whining about
as a 2.6.23 regression.
Running the watchdog timer all the time is unneeded. Change it
to run only if link is up, and reduce frequency to save power.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an optional debug interface for displaying state of transmit/receive
rings. Creates a file debugfs/sky2/ethX for each device that is up.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Enable support for Yukon EX chipset (88e8071).
Most of changes are related to new commands to chip for transmit,
and change in status and checksumming.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The General Purpose I/O register is yet another hardware workaround
catchall. Enable workaround that vendor driver does to stay
but for bug compatiable.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This register is more of a test and control register on Yukon2.
So rename it to Q_TEST and give some bit definitions.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to setup more PCI control control registers are on Yukon EX.
Some of these also exist on Yukon EC-U as well.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't want IRQ on FIFO error because there is nothing useful to do with it.
But do want IRQ on duplex change.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This code inherited from the sk98lin driver is incorrect on the Yukon2.
The GPHY_CTRL register values are specific to the internal PHY of the chip
and the values used were leftovers.
Driver was setting bit 13 which is now the INT polarity for the PHY!
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC Ultra chips have transmit settings for store and
forward and PCI buffering. By setting these appropriately, normal
performance goes from 750Mbytes/sec to 940Mbytes/sec (non-jumbo).
It is also possible to do Jumbo mode, but it means turning off
TSO and checksum offload so the performance gets worse. There isn't
enough buffering for checksum offload to work.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There should never be descriptor error unless hardware or driver is buggy.
But if an error occurs, print useful information, clear irq, and recover.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit timeout code could hang, and it would not clear out
problems if the hardware was stuck. Change the code to effectively do
a device down/up similar to the suspend/resume code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't mark pause frames as errors. This problem caused transmitter not
to pause and would effectively take out a gigabit switch because the
it can't handle overrun.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is basic support for the new Yukon Extreme
chip, extracted from the new vendor driver 10.0.4.3.
Since this is untested hardware, it has a big fat warning for now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adds basic magic packet wake on lan support to the sky2 driver.
Note: initial WOL value is based on BIOS settings.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve power management and error handling by using pci_set_power_state(),
instead of driver doing PCI PM register changes in the driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of sparse warnings in sky2 driver because of mixed enum
usage.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the receive performance on some systems go from
714MB/s to 941MB/s. It adjusts the watermark of the receive queue
to be lower, thereby avoiding excess hardware flow control. This is
most important on the systems which have little/no additional buffering.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If using Message Signaled Interrupts (MSI) then the IRQ will never
be shared. Don't call pci_disable_msi() unless using MSI.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update workarounds for 88E803X based on the latest SysKonnect vendor
driver version (8.41). Tested on EC_U rev A1, only.
These up the receive performance.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts earlier change that attempted to fix flow control.
Device needs to discard pause frames, otherwise it hangs after a while.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The result of flow control negotiation should not limit the next
negotiatition. If board is plugged into an old half duplex 10Mbit port,
without pause, then replugged into a gigabit port, it should negotiate
what is desired, not inherit that last negotiation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The pci express error handling extensions don't work unless PCI access is via
mmconfig. Otherwise, all accesses to pci config registers greater than 256 fail.
Since the sky2 driver has other ways of getting to PCI config space, it works
around this short coming, but the pci_find_ext_capablity doesn't work.
This backs out commit 91aeb3edbc
Go back to hardcoding, since we know where the error registers are anyway.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=7222
Signed-off-by: Stephen Hemminger <shemmminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use hardware support for chained receive to break up large frames
into multiple pages. This avoids having to do a mult-page allocation
that can fail on a busy system due to fragmented memory.
For normal size MTU, this code behaves the same.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netdevice transmit lock via netif_tx_lock rather than putting
lock in device specific code and using lockless transmit. The code is
cleaner using netif_tx_lock, and the performance is same.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since a transmit can take several control blocks, the old code waited
until the last control block was marked as done. This code processes
the return values incrementally. This makes slots in the tx ring available
and less chance of getting stuck.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the standard pci capability mechanism to access PCI express error
registers, rather than hard coding the offset. Mask off the PCI express
error from ever occuring on non-PCI express systems.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix support for big endian platforms like PPC.
Still not sure about VLAN acceleration (does it need swapping)?
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the support for fiber connected gigabit boards.
Allow half duplex gigabit to be configured.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix problems with transmit pause frames. The driver was telling the
GMAC to flush (not process) pause frames. Manually disabling pause wasn't
working because of problems in the setup.
This maybe the cause of the lockup under load.
http://bugzilla.kernel.org/show_bug.cgi?id=6839
Patch against netdev-2.6 git tree
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since many packets have the same checksum starting offset and insertion
location; the driver can save the last information and only tell hardware
when it changes.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't use force status bit. It was never implemented on all chips, or has
no impact.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in sky2 driver. Should be
three bits wide, but the mask only allows for 1 bit to be set.
Thanks & Regards
Neil
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
sky2.h | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sky2 driver will oops referencing bad memory if used on
a dual port card. The problem is accessing past end of
MIB counter space.
Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware has additional error trap interrupt bits. I have never seen
them trigger, but if they do, it looks like this might be useful.
Signed-off-by: Stephen Hemminger <shemminger@osdl.rog>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Redo the interupt handling of sky2 driver based on the IRQ mangement
documentation. All interrupts are handled by the device0 NAPI poll
routine.
Don't need to adjust interrupt mask in IRQ context, done only when
changing device under RTNL. Therefore don't need hwlock anymore.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove wake on lan support for now. It doesn't work right, and I
don't have a machine with working suspend/resume to test or fix it.
It will be re-enabled later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC/rev0 (A1) chipset requires a bunch of workarounds. I copied these
from sk98lin. But since they never got tested and add more cruft to the code;
any attempt at using driver as is on this version will probably fail.
It looks like this was a early engineering sample chip revision, if it ever shows
up on a real system. Produce an error message.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.
In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to avoid race in updating IRQ mask. This can probably be replaced
smarter use of the interrupt control registers (if/when chipset
docs are available).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
To avoid problems with PCI config access without ACPI (or busted ACPI tables),
use the device's window into PCI config space.
I know this probably will upset the purists, but I would rather have users
than ACPI testers. It also generates less code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
