This commit adds MIDI functionality with an assumption of 'if the device
has MIDI comformant data channels in its stream formation, the device has
one MIDI port'.
When no streams have already started, MIDI functionality starts stream
with current sampling rate.
When MIDI functionality has already starts some streams and PCM
functionality is going to start streams at different sampling rate,
this driver stops streams once and changes sampling rate, then restarts
streams for both PCM/MIDI substreams.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, a support for transmitted packets is added. This commit
add a support for capturing PCM samples.
When any streams are already started, this driver should not change sampling
rate of the device, thus this commit also adds a restriction of sampling rate
in this situation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices produced by Behringer/Mackie are based on OXFW970/971. This
commit adds support for them. Additionally, this commit changes the way to
name card with some information in config rom.
Ids of some Mackie(Loud) models are not identified, therefore this commit
applies name detection for these models.
The devices support capture/playback of PCM-samples and some of them
supports capture/playback of MIDI messages. These functionalities are
implemented by followed commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In past commit, this driver can keep stream formations for each sampling
rate. So its stream functionality can decide stream formations with given
some parameters.
This commit moves related codes from PCM functionality to stream
functionality. Furthermore, to set stream format correctly, this commit
uses AV/C Stream Format Information command instead of AV/C Input/Output
Plug Signal Format command.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds proc interface to get information about stream
formation. This commit also adds snd_oxfw_stream_get_current_formation()
to get current stream formation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, this driver can get to know stream formations at
each supported sampling rates. This commit uses it to make PCM
rules/constraints and obsoletes hard-coded rules/constraints.
For this purpose, this commit adds 'struct snd_oxfw_stream_formation' and
snd_oxfw_stream_parse_format() to parse data channel formation of data
block.
According to datasheet of OXFW970/971, they support 32.0kHz to 196.0kHz.
As long as developers investigate, some devices are confirmed to have
several formats for the same sampling rate.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
OXFW970/971 may supports AV/C Stream Format Information Specification 1.1
Working Draft (Apr 2005, 1394TA). By using this command, drivers can get to know
stream formations which device supports.
This commit adds 'EXTENDED STREAM FORMAT INFORMATION' command. This command
has two subfunctions, 'SINGLE' and 'LIST'. Drivers can use 'SINGLE' subfunction
to know/set current formation of AMDTP stream, Drivers can use 'LIST'
subfunction to know an available formation of AMDTP stream in a certain sampling
rate.
But some devices don't implement the 'LIST' subfunction. So this commit uses
an assumption that 'if they don't implement it, they don't change stream
formation depending on current each sampling rate'. With this assumption, this
driver generates formations for such devices by:
1.getting current formation by SINGLE subfunction
2.getting supported sampling rates
3.applying current formation for all of supported sampling rates
Followed commit implements a parser of this format information.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preparation for more models. In following commit, members
of 'struct snd_card' related to name becomes to consists of vendor and
model strings in device's config-rom.
Current supported devices also has strings in their config rom, but the
strings are too long to name sound card, thus this driver still keep
hard-coded vendor and model names for them.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a support for MIDI capture/playback
When MIDI substrams already start streaming and PCM substreams are going to
join at different sampling rate, streams are stopped once. Then sampling rate
is changed and streams are restarted.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a support for capturing PCM samples.
When opposite PCM substream is already running, available sampling rate is
limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to handle devices with non SYT-Match
sampling clock source.
When sampling clock source is SYT-Match mode, devices handle
'presentation timestamp' in received packets and generates sampling clock
according to the information. In this case, driver is synchronization master
and must transfer correct value in SYT field of each packets in outgoing
stream, then the outgoing stream is a master stream.
On the other hand, non SYT-Match mode, devices do this. So drivers must pick
up the value in SYT field of incoming packets and use the value for outgoing
stream. Currently firewire-lib module achieve this work.
Furthermore, without SYT-Match and internal clock source, the sampling rate
should be fixed for the other devices connected to the handled device. This
commit add a restriction of sampling rate at this situation.
With these implementations, this driver has no need to set clock source.
This commit remove set function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds support for AMDTP in-stream. As a result, Dice driver
supports full duplex streams with synchronization.
AMDTP can transfer timestamps in its packets. By handling the timestamp,
devices can synchronize to the other devices or drivers on the same bus.
When Dice chipset is 'enabled', it starts streams with correct settings.
This 'enable' register is global, thus, when a stream is started to run,
an opposite stream can't start unless turning off 'enable'. Therefore
a pair of streams must be running. This causes a loss of CPU usage when
single stream is needed for neither playbacking or capturing.
This commit assumes that playback-only models also have a functionality
to transmit stream for delivering timestamps.
Currently, sampling clock source is restricted to SYT-Match mode. This is
improved in followed commit. I note that at SYT-Match mode, Dice can select
from 4 streams for synchronization but this driver uses the 1st stream only
for simplicity.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Streaming functionality can start streams when rate is given but currently
some codes are in PCM functionality.
This commit changes the way to start stream and add some arrangement
to make it easy to understand the way.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a help for works in followed patches.
And this commit remove 'fw_unit_get()/fw_unit_put()' because these
are called by helper functions in 'snd-firewire-lib'.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Followed commits add much codes. To make the work easy, this commit creates
own directory and move current file to it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit renames 'firewire-speakers' to 'oxfw' to enhance support for
devices which based on OXFW970/971. A line for MODULE_ALIAS is added.
Additionally, to help for works in followed paches, some members
in private structure are renamed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some developers test this driver, thus it's better to remove its
experimental state.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new functions and some arrangement for PCM restriction.
This arrangement is due to the number of channels which each Dice device has.
I note that minimum number for period becomes 2, instead of 1 because its PCM
functionality has SNDRV_PCM_INFO_BATCH, this means that the driver uses double
(or more) buffering so the minimum number for period should be 2.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to proc output.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to hwdep functionality.
This interface is designed for mixer/control application. By using hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Additionally, this interface give a way to read Dice notification.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to PCM functionality.
Currently PCM playback is supported. PCM capture will be supported in followed
commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file with some helper functions for streaming, and move some
codes into the file with some arrangements.
Well-known CMP is not used to start/stop streams for Dice chipset. It's
achieved by writing to specific address. We call this way as 'enable'.
When devices are 'enabled', streaming starts in registered isochronous channel.
Some helper functions are already implemented in previous commit.
Basically, the stream is compliant to IEC 61883-6, so-called as AMDTP. But Dice
has a specific quirk, so called-as 'Dual Wire'. This quirk is applied at
176.4/192.0kHz. In this mode, each packet includes double number of events than
number in the specification, and stream runs at a half of sampling rate.
There is another quirk at bus reset. Dice chipset handles drivers' request but
don't re-enable streaming. So stream should be stopped.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file with some helper functions for transaction, and move
some codes into the file with some arrangements.
For Dice chipset, well-known FCP or AV/C commands are not used to control
devices. It's achieved by read/write transactions into specific addresses.
Dice's address area is split into 5 areas. Each area has its own role. The
offset for each area can be got by reading head of the address area. By
reading these areas, drivers can get to know device status. By writing these
areas, drivers can change device status.
Dice has a specific mechanism called as 'notification'. When device status is
changed, Dice devices tells the event by sending transaction. This notification
is sent to an address which drivers register in advance. But this causes an
issue to drivers.
To handle the notification, drivers need to allocate its own callback function
to the address region in host controller. This region is exclusive. For the
other applications, drivers must give a mechanism to read the received
notification. For this purpose, Dice driver already implements hwdep interface.
Dice chipset doesn't allow drivers to register several addresses. In this
reason, when this driver is applied to a device, the other drivers should
_not_ try to register its own address to the device.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In followed commits, dice driver is split into several files. For easily
managing these files, this commit adds subdirectory and move file into
the directory.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, dice driver supports AMDTP out-stream. In followed commits, AMDTP
in-stream will be supported but current name of members in dice structure
are not propper. This commit renames these members to proper name.
Additionally, for easily distinguishing local symbols from structure tag,
rename dice tag into snd_dice.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The checkpatch.pl generates some warnings due to:
- C99 comment
- a line over 80 characters
- min() for parameters with different types
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Complete missing parameters, correct wrong reference, and add an explaination
about the differences between the latest specification and our implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_bebob_stream_check_internal_clock() may get an id from
saffirepro_both_clk_src_get (via clk_src->get()) that was uninitialized.
a) make logic in saffirepro_both_clk_src_get explicit
b) test if id used in snd_bebob_stream_check_internal_clock matches array size
[fixed missing signed prefix to *_maps[] by tiwai]
Signed-off-by: Christian Vogel <vogelchr@vogel.cx>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Terratec PHASE 88 rack fw has two registers for source of clock, one is
for internal/external, and another is for wordclock/spdif for external.
When clock source is internal, information in another register has no meaning.
Thus it must be ignored, but current implementation decodes it. This causes
over-indexing reference to labels.
Reported-by: András Murányi <muranyia@gmail.com>
Tested-by: András Murányi <muranyia@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes a failure to open PCM device with -ENOSYS in
Terratec Phase 88.
Terratec Phase 88 has two Selector Function Blocks of AVC Audio subunit
to switch source of clock. One is to switch internal/external for the
source and another is to switch word/spdif for the external clock.
The IDs for these Selector Function Blocks are 9 and 8. But in current
implementation they're 0 and 0.
Reported-by: András Murányi <muranyia@gmail.com>
Tested-by: András Murányi <muranyia@gmail.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, one data block transfers one event. In ALSA, the event equals one PCM frame,
hence one data block transfers one PCM frame. But Dice has a quirk at higher sampling rate
(176.4/192.0 kHz) that one data block transfers two PCM frames.
Commit 10550bea44 ("ALSA: dice/firewire-lib: Keep dualwire mode but obsolete
CIP_HI_DUALWIRE") moved some codes related to this quirk into Dice driver. But the commit
forgot to add arrangements for PCM period interrupts and DMA pointer updates. As a result, Dice
driver cannot work correctly at higher sampling rate.
This commit adds 'double_pcm_frames' parameter to amdtp structure for this quirk. When this
parameter is set, PCM period interrupts and DMA pointer updates occur at double speed than in
IEC 61883-6.
Reported-by: Daniel Robbins <drobbins@funtoo.org>
Fixes: 10550bea44 ("ALSA: dice/firewire-lib: Keep dualwire mode but obsolete CIP_HI_DUALWIRE")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The channel mapping is initialized by amdtp_stream_set_parameters(), however
Dice driver set it before calling this function. Furthermore, the setting is
wrong because the index is the value of array, and vice versa.
This commit moves codes for channel mapping after the function and set it correctly.
Reported-by: Daniel Robbins <drobbins@funtoo.org>
Fixes: 10550bea44 ("ALSA: dice/firewire-lib: Keep dualwire mode but obsolete CIP_HI_DUALWIRE")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use %d for loop counter and %X for device capabilities. This is a
supplemental patch for Hans Wennborg's patch.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a supplement to my previous patch.
http://mailman.alsa-project.org/pipermail/alsa-devel/2014-July/079190.html
The special_clk_ctl_put() still returns 0 in error handling case. It should
return -EINVAL.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is for correction of my misunderstanding about return value of
.put callback in ALSA Control interface.
According to 'Writing ALSA Driver' (*1), return value of the callback has
three patterns; 1: changed, 0: not changed, an negative value: fatal error.
But I misunderstood that it's boolean; zero or nonzero.
*1: Writing an ALSA Driver (2005, Takashi Iwai)
http://www.alsa-project.org/main/index.php/ALSA_Driver_Documentation
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit uses different labels for control elements of digital input/output
interfaces to correct my misunderstanding about M-Audio Firewire 1814 and
ProjectMix I/O.
According to user manuals for these two models, they have two modes for
digital input; one is S/PDIF in both of optical and coaxial interfaces,
another is ADAT in optical interface only.
But in current implementation, a control element for it reduced labels which
a control element for digital output uses because of my misunderstanding
that optical interface is not available for digital input with S/PDIF mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In error handling case, special_clk_ctl_put() returns without unlock_mutex(),
therefore the mutex is still locked. This commit moves mutex_lock() after
the error handling case.
This commit is my solution for this post.
[PATCH -next] ALSA: bebob: Fix missing unlock on error in special_clk_ctl_put()
https://lkml.org/lkml/2014/7/20/12
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently mutex_destroy() is called in module's cleanup function. But after
cleaned up, this mutex is automatically released. So this function call
is meaningless.
[fixed a typo in changelog by tiwai]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
