Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.
However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.
This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is an incremental fix of commit
e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").
After commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().
Current code only exclude the checking of wp_type for dt platform which
does not make sense.
This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.
Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
Fixes: 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes: 66b50a0099 ("mmc: esdhc: Add support for 8-bit bus width and..")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should not call dma_free_coherent if host->adma_table is NULL,
otherwise may trigger panic.
Fixes: d1e49f77d7 ("mmc: sdhci: convert ADMA descriptors to a...")
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometimes BADA, DEB or CEB error interrupts occur when sd card is
unplugged during data transfer. These interrupts are currently ignored
by the interrupt handler. But, this results in card not being
recognised on subsequent insertion. This is because mmcqd is waiting
forever for the data transfer(for which error occurred) to complete.
Fix this, by reporting BADA, DEB, CEB errors to mmc-core as -EILSEQ, so
that the core can do appropriate handling.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTO/DCRC errors were not being informed to the mmc core since
commit ae4bf788ee ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().
Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.
Fix this by checking for 'host->data' before it is actually cleared.
Fixes: ae4bf788ee ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ")
CC: stable@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This flag is currently never cleared, which can in rare cases
trigger a warn-on if it is still set but the block isn't
InSync.
So clear it when it isn't need, which includes if the replacement
device has failed.
Signed-off-by: NeilBrown <neilb@suse.com>
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: David Teigland <teigland@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
bitmap_read_sb is modifying mddev->bitmap_info.offset. This works for
the first bitmap read. However, when multiple bitmaps need to be opened
by the same node, it ends up corrupting the offset. Fix it by using a
local variable.
Also, bitmap_read_sb is not required in bitmap_copy_from_slot since
it is called in bitmap_create. Remove bitmap_read_sb().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
request_module() can return 256 (process exited) in some cases,
which is not as specified in the documentation before the
request_module() definition. Convert the error to -ENOENT.
The positive error number results in bitmap_create() returning
a value that is meant to be an error but doesn't look like one,
so it is dereferenced as a point and causes a crash.
(not needed for stable as this is "experimental" code)
Fixes: edb39c9ded ("Introduce md_cluster_operations to handle cluster functions")
Signed-off-By: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
If the bitmap read fails, the error code set is -EINVAL. However,
we don't check for errors and go ahead with cluster_setup.
Skip the cluster setup in case of error.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 76073054c9 ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NeilBrown <neilb@suse.com>
Regression fix for systemd getting confused about unknown connector state
after resume. Just stop setting the state to unknown, turned out to be a
silly idea anyway. What drivers imo really should do (and i915 still does
that) is forcing a full reprobe on resume to make sure connector changes
while suspended are caught. Most drivers seem to get this wrong. Otoh it
took us years to get fixes merged where some probe races resulted in
eating uevents, I guess userspace expectations for reliable hpd are just
really low :(
* tag 'topic/drm-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
drm: Stop resetting connector state to unknown
arb_timer kernel side fix from Chris.
* tag 'drm-intel-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Use two 32bit reads for select 64bit REG_READ ioctls
Some amdgpu fixes.
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu/cz/dpm: properly report UVD and VCE clock levels
drm/amdgpu/cz: implement voltage validation properly
drm/amdgpu: add VCE harvesting instance query
drm/amdgpu: implement VCE 3.0 harvesting support (v4)
drm/amdgpu/dce10: Re-set VBLANK interrupt state when enabling a CRTC
drm/amdgpu/dce11: Re-set VBLANK interrupt state when enabling a CRTC
Return proper pgprot for ARM64. This is required for objects like
Nouveau fences to be mapped with expected coherency.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:
CPU 0 | CPU 1
|
uart_close() |
tty_port_close_start() |
tty->closing = 1 |
tty_ldisc_flush() |
| => IRQ
| while (LSR & data ready)
| uart_insert_char()
| tty_flip_buffer_push()
| <= EOI
stop_rx() | .
uart_shutdown() | .
free xmit.buf | .
tty_port_tty_set(NULL) | .
tty->closing = 0 | .
| flush_to_ldisc()
| n_tty_receive_buf_common()
| __receive_buf()
| ...
| commit_echoes()
| uart_flush_chars()
| __uart_start()
| ** OOPS on port.tty deref **
tty_ldisc_flush() |
Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().
[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.
Fixes: 2e75891083 ("serial: core: Flush ldisc after dropping port
mutex in uart_close()")
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c627f2ceb6 ("serial: 8250: Add support for big-endian MMIO accesses")
added support for 32-bit big-endian mmio to the 8250 driver. Support for
ioreadXXbe/iowriteXXbe io accessors was missing from m32r arch, which caused
build errors.
Add trivial macro mmio accessors.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 068500e08d.
According to some tests, SDMA support is broken at least for i.MX6 without
HW flow control. Different forms of data-corruption appear either with
the ROM firmware for the SDMA controller as well as when loading Freescale
provided SDMA firmware versions 1.1 or 3.1.
Signed-off-by: David Jander <david@protonic.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calls to regmap_raw_read/write needed register rewrite in a
similar way as function calls to regmap_read/write already had.
This enables reading/writing the serial datastream to the device.
Signed-off-by: Bo Svangård <bo.svangard@embeddedart.se>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I2C=m and SPI=y or-ing them will produce =y while
what we need is the lower bound, i.e. =m. Fortunately
SPI is a boolean so we need to handle only one special
case.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In probe, we use dev_id as array index of etraxfs_uart_ports and store the
index in port->line. So etraxfs_uart_ports[port->line] should be released
when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a data corruption bug when using discard on top of MD linear,
raid0 and raid10 personalities.
Commit 20d0189b10 "block: Introduce new bio_split()" permits sharing
the bio_vec between the two resulting bios. That is fine for read/write
requests where the bio_vec is immutable. For discards, however, we need
to be able to attach a payload and update the bio_vec so the page can
get mapped to a scatterlist entry. Therefore the bio_vec can not be
shared when splitting discards and we must do a full clone.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Seunguk Shin <seunguk.shin@samsung.com>
Tested-by: Seunguk Shin <seunguk.shin@samsung.com>
Cc: Seunguk Shin <seunguk.shin@samsung.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: <stable@vger.kernel.org> # v3.14+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling signalling char, claim the termios write lock before
signalling waiting readers and writers to prevent further i/o
before flushing the echo and output buffers. This prevents a
userspace signal handler which may output from racing the terminal
flush.
Reference: Bugzilla #99351 ("Output truncated in ssh session after...")
Fixes: commit d2b6f44779 ("n_tty: Fix signal handling flushes")
Reported-by: Filipe Brandenburger <filbranden@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen. Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.
According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.
The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Cc: stable@vger.kernel.org
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* bmc150_magn - add missing regmap dependency and ensure on a wrong chip
case report hte chip id rather than a previous return value.
* mmc35240 - Fill a null pointer derefrence and wrong SET / RESET logic
that results in North and South being swapped.
* mlx96014 - correct the offset value reported to userspace (wrong sign)
* vf610 - Prevent non aligned register reading.
* mcp320x - Another null pointer deference bug.
* mma8452 - change threshold type from THRESH to MAG to reflect the fact
that the sign of the signal is not known when the event is signaled.
* stk3310 - move device registert to end of probe to avoid race conditions
when coming up, check for invalid client->irq values and make it work
for both endian types of host.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=AEVb
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.2c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
3rd round of IIO fixes for the 4.2 cycle.
* bmc150_magn - add missing regmap dependency and ensure on a wrong chip
case report hte chip id rather than a previous return value.
* mmc35240 - Fill a null pointer derefrence and wrong SET / RESET logic
that results in North and South being swapped.
* mlx96014 - correct the offset value reported to userspace (wrong sign)
* vf610 - Prevent non aligned register reading.
* mcp320x - Another null pointer deference bug.
* mma8452 - change threshold type from THRESH to MAG to reflect the fact
that the sign of the signal is not known when the event is signaled.
* stk3310 - move device registert to end of probe to avoid race conditions
when coming up, check for invalid client->irq values and make it work
for both endian types of host.
Pull namespace fixes from Eric Biederman:
"While reading through the code of detach_mounts I realized the code
was slightly off. Testing it revealed two buggy corner cases that can
send the code of detach_mounts into an infinite loop.
Fixing the code to do the right thing removes the possibility of these
user triggered infinite loops in the code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
mnt: In detach_mounts detach the appropriate unmounted mount
mnt: Clarify and correct the disconnect logic in umount_tree
Bugfixes and documentation fixes. Igor's patch that allows
users to tweak memory table size is borderline,
but it does fix known crashes, so I merged it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVpBzpAAoJECgfDbjSjVRpQXEIAMEqetqPuRduynjIw2HNktle
fe/UUhvipwTsAM4R2pmcEl5tW04A/M54RkXN4iVy0rPshAfG3Fh4XTjLmzSGU0fI
KD6qX8/Zc/+DUWnfe3aUC6jOOrjb7c4xRKOlQ9X8lZgi2M6AzrPeoZHFTtbX34CU
2kcnv5Sb1SaI/t2SaCc2CaKilQalEOcd59gGjje2QXjidZnIVHwONrOyjBiINUy6
GzfTgvAje8ZiG6951W3HDwwSfcqXezin27LJqnZgaLCwTCKt2gdQ2MAKjrfP2aVF
+gX2B4XxcFLutMVx/obsjvA1ceipubyUauRLB3mnO3P5VOj1qbofa2lj4pzQ80k=
=EKPr
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes from Michael Tsirkin:
"Bugfixes and documentation fixes.
Igor's patch that allows users to tweak memory table size is
borderline, but it does fix known crashes, so I merged it"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: add max_mem_regions module parameter
vhost: extend memory regions allocation to vmalloc
9p/trans_virtio: reset virtio device on remove
virtio/s390: rename drivers/s390/kvm -> drivers/s390/virtio
MAINTAINERS: separate section for s390 virtio drivers
virtio: define virtio_pci_cfg_cap in header.
virtio: Fix typecast of pointer in vring_init()
virtio scsi: fix unused variable warning
vhost: use binary search instead of linear in find_region()
virtio_net: document VIRTIO_NET_CTRL_GUEST_OFFLOADS
bio_associate_blkcg(), bio_associate_current() and wbc_account_io()
are used to implement cgroup writeback support for filesystems and
thus need to be exported. Export them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <axboe@fb.com>
The fixes include:
* A couple of fixes for the new ARM-SMMUv3 driver to fix issues found
on the first real implementation of that hardware.
* A patch for the Intel VT-d driver to fix a domain-id leak.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zWOU
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"The fixes include:
- a couple of fixes for the new ARM-SMMUv3 driver to fix issues found
on the first real implementation of that hardware.
- a patch for the Intel VT-d driver to fix a domain-id leak"
* tag 'iommu-fixes-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix VM domain ID leak
iommu/arm-smmu: Skip the execution of CMD_PREFETCH_CONFIG
iommu/arm-smmu: Enlarge STRTAB_L1_SZ_SHIFT to support larger sidsize
iommu/arm-smmu: Fix the values of ARM64_TCR_{I,O}RGN0_SHIFT
iommu/arm-smmu: Fix LOG2SIZE setting for 2-level stream tables
iommu/arm-smmu: Fix the index calculation of strtab
VCE, UVD DPM work similarly to SCLK DPM. Report the current
clock levels for UVD and VCE via debugfs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CZ uses a different set of registers compared to previous asics
and supports separate NB and GFX planes.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were previously using free_bootmem() and just getting lucky
that nothing too bad happened.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: stable@vger.kernel.org
The handling of in detach_mounts of unmounted but connected mounts is
buggy and can lead to an infinite loop.
Correct the handling of unmounted mounts in detach_mount. When the
mountpoint of an unmounted but connected mount is connected to a
dentry, and that dentry is deleted we need to disconnect that mount
from the parent mount and the deleted dentry.
Nothing changes for the unmounted and connected children. They can be
safely ignored.
Cc: stable@vger.kernel.org
Fixes: ce07d891a0 mnt: Honor MNT_LOCKED when detaching mounts
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
For boards with bad VCE blocks, only configure the working
block.
v2: use the harvest info for pipe setup
v3: fix mask check as noted by Leo
v4: add dGPU support
Reviewed-by: Christian König <christian.koenig@amd.com> (v2)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This doesn't seem strictly necessary with Tonga right now, but that might
change with future power management enhancements.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Something (ATOM BIOS?) seems to be clobbering the LB_INTERRUPT_MASK
register while the CRTC is off, which caused e.g. glxgears or
gnome-shell to hang after a modeset.
Reviewed-and-Tested-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Sonny Jiang <sonny.jiang@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
