* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
It's common gpiolib for recent Samsung SoCs. Move to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
The generic chip infrastructure has had a Kconfig symbol added so we need
to select that for the kernel to link now we're using the generic IRQ
chip infrastructure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2416, S3C2443 and S3C2450 includes a USB High-Speed Gadget controller module.
This patch adds the following for supporting this controller.
1. Definition for USB High-Speed controller base address.
2. Platform device instantiation.
3. Declaration for platform data structure.
4. Functionality to setup platform data for the controller.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
Let's remove the static qualifier from current offenders, or turn them
into const variables when possible. Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Replace sysdev classes and struct sys_device objects used for "core"
power management by Samsung platforms with struct syscore_ops objects
that are simpler.
This generally reduces the code size and the kernel memory footprint.
It also is necessary for removing sysdevs entirely from the kernel in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
s3c_pm_show_resume_irqs() is used by some s3c_pm_arch_show_resume_irqs()
implementations, which get included through mach/pm-core.h. Add __maybe_unused
to silence warnings when it isn't used (e.g. on S3C64XX platforms).
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error that occurs on enabling the Samsung
specific PM CRC check code. Missed removing this reference of
s3c_sleep_save_phys during move to generic cpu suspend/resume
support.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Reorder
irq_set_chip()
irq_set_chip_data()
irq_set_handler()
to
irq_set_chip()
irq_set_handler()
irq_set_chip_data()
so the next patch can combine irq_set_chip() and irq_set_handler() to
irq_set_chip_and_handler().
Automated conversion with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes CPU idmask of S5P64X0 and EXYNOS4210
and its comparison method because just want to use CPU
id for it.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
This patch removes all global data from common s5p gpio interrupt
handler code. This enables to reuse this code on EXYNOS4 platform.
Instead of global data (IRQ_GPIOINT interrupt number,
S5P_GPIOINT_GROUP_MAXNR groups count), a s5p_register_gpioint_bank()
function is introduced. It is aimed to be called from gpiolib init.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds the device definitions, platform specific initialization
and clocks for SATA on ARMLEX4210.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support suspend to ram for EXYNOS4210.
As a note, this includes function of outer cache flush
because it is used before entering PM.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for fourth FIMC platform device definition and define
resources for FIMC modules on EXYNOS4 machines.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ensures that the declaration agrees with the definition and makes sparse
happy.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch does the following:-
1. It moves file pwm.c from plat-s3c24xx to plat-samsung. This will
enable all machines with Samsung SoCs to make use of the same code.
2. The device definitions have been separated to a new file dev-pwm.c
for better clarity and structure.
3. It will enable all Samsung S3C and S5P series SoC's to use common
PWM Kconfig definition.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates device support of EXYNOS4 according to the change of
ARCH name, EXYNOS4.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
s3c24xx_ts_set_platdata is annotated __init and not used by any module,
thus don't export it.
This patch fixes below warning:
WARNING: arch/arm/plat-samsung/built-in.o(__ksymtab+0x90): Section mismatch
in reference from the variable __ksymtab_s3c24xx_ts_set_platdata to the
function .init.text:s3c24xx_ts_set_platdata()
The symbol s3c24xx_ts_set_platdata is exported and annotated __init
Fix this by removing the __init annotation of s3c24xx_ts_set_platdata
or drop the export.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Previously we were relying on it being pulled in by other headers for
the prototype of s3c24xx_irq_suspend() and s3c24xx_irq_resume().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support System MMU for S5PV310 and S5PC210.
Signed-off-by: Donguk Ryu <du.ryu@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: changed SYSMMU config name]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for clock information exposed to debug-fs interface.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[kgene.kim@samsung.com: removed useless empty lines]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are few functions marked as __init, but exported to modules in
devices declaration files.
s3c_nand_set_platdata() and s3c24xx_ts_set_platdata() are used only by
boards init code now, so remove EXPORT_SYMBOL() for them.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2443 has two-bits pull-up/pull-down configuration fields in GPIO
registers, but values are differ from other SoCs with two-bits
configuration. gpio-cfg-helpers.h already has prototypes for
s3c2443-style pull-up/down methods, so implement them.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samsung S3C2416 has two SDHCI controllers compatible with other
Samsung's SoCs (S3C64XX, S5PC100 etc...).
Add required platform setup code that the devices can be used with
sdhci-s3c driver.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
[kgene.kim@samsung.com: change to __raw_{readl,writel} from {readl,writel}]
[kgene.kim@samsung.com: build error fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>