Put a small comment before assigning IRQ_WAKE_THREAD
telling us what is going on.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Yann Gautier <yann.gautier@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210921143359.1738149-1-linus.walleij@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA is only available on controller instances that are connected to the
L3 interconnect and are bus mastering capable.
As the MMCHS_HL_HWINFO is in the module registers before omap registers
and sdhci registers, and the omap registers and sdhci registers can be
at different offsets depending on the SoC, let's read MMCHS_HL_HWINFO
directly.
Let's also switch to using device_property_present() while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-6-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to support the legacy ti,non-removable property too. Let's warn
about the legacy property and mark the device as non-removable.
Naturally all the mainline kernel devicetree files will get updated to use
the standard non-removable property with the sdhci-omap conversion. But we
also have folks updating their kernels with custom devicetree files that
we need to consider.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-5-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sysconfig register is managed in a generic way by PM runtime for us by
the interconnect target module layer code. SDHCI_RESET_ALL also resets the
target module configuration, so we need to restore sysconfig after reset.
Note that there is no need to save and restore sysconfig during PM runtime,
the PM runtime layer will do that for us.
Not sure if this issue is a problem with the current configurations, I
noticed the issue while adding support for older TI SoCs and testing with
wlcore SDIO wlan device.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-4-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to restore context in a specified order with HCTL set in two
phases. This is similar to what omap_hsmmc_context_restore() is doing.
Otherwise SDIO can stop working on resume.
And for PM runtime and SDIO cards, we need to also save SYSCTL, IE and
ISE.
This should not be a problem currently, and these patches can be applied
whenever suitable.
Fixes: ee0f309263 ("mmc: sdhci-omap: Add Support for Suspend/Resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address
00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)
AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.
Fixes: 7d326930d3 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to JEDEC Spec, there is no need to do tuning under HS400 mode
since the Rx signal is aligned with the DS signal. However, MediaTek's IC
need set its "DS delay" internally to ensure it can latch Rx signal
correctly.
In previous version, We provide an "hs400-ds-delay" in device tree to cover
different chipset/PCB design, and it works fine in most cases. But, with
the development of process technology and the big VCore voltage scale
range(may have 0.7V/0.6V/0.55V), it is difficult to find a suitable
"hs400-ds-delay" to cover all of IC corner cases(SSSS/TTTT/FFFF). So that
We must have the ability to do hs400 online tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsunhg.com>
Link: https://lore.kernel.org/r/20210916170511.137915-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel Thunder Bay SoC eMMC controller is based on Arasan
eMMC 5.1 host controller IP
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210829182443.30802-2-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the helper macro SET_RUNTIME_PM_OPS() instead of the verbose
operators ".runtime_suspend/.runtime_resume", because the
SET_RUNTIME_PM_OPS() is a nice helper macro that could be brought
in to make code a little more concise.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210907025940.1535-1-caihuoqing@baidu.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_request structure(*mrq) is not used. //msdc_cmd_find_resp
I remove the unnecessary code related to the mmc_request structure.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20210827093119.32481-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We found this issue on a 5G platform, during CMDQ error handling, if DMA
status is active when it call msdc_reset_hw(), it means mmc host hw reset
and DMA transfer will be parallel, mmc host may access sram region
unexpectedly. According to the programming guide of mtk-sd host, it needs
to wait for dma stop done after set dma stop.
This change should be applied to all SoCs.
Signed-off-by: Derong Liu <derong.liu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210827071537.1034-1-derong.liu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The
fix we agreed on in the end is to make this symbol selected by any
driver using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in v5.15.
There is a small merge conflict against an earlier partial fix for the
QCOM_SCM dependency problems.
Finally, the branch also includes a small unrelated build fix for NOMMU
architectures.
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmFgVp8ACgkQmmx57+YA
GNlQoA/+O0ljtTy5D0MjRGmFDs11M5AtKNrfys82lm2GeEnc4lnxn722jLk8kR6s
y6DSOWFs7w1bqhKExQNehZYtJO3sgW/9qiLMV9qfOx1Nc6WwhDPcYM9bMyGlpTmL
M456nh8NopixV7slanNtfz1e0kbMKoK+4Ub7M5OHepK6x9FKQXQYQpeoBxaXHmWZ
9eaRiL/CsRHO/cSkvpq1GtL7IVrudvij3FDHzxoDGFFjkCUm9LiN/8yrnVxHA9G7
3EPyJazI559SsnxXJR32udGPJWZV1HZ7D5gbxDvzr5rZ9EX0JpyPGJsuXUR1wqlS
UB2Y7AUTSxkwDiZ8UhPoXn6i67WAirzEsP2WmdS4v6NEbxlNloLGTIeGwcwkCRMU
DBvMtDW8kKusgVu/OkEUgoC6MTRt+Mg+gZcQI/C4sp0MqZGaMY6c7abnYjqwEzBV
ARS7bUYyME2GL6wNDPFB8esuD9jjdFXy96bGHATmzMxT3012K3X7ufFOzJZ+GOF9
pan00fgoC17oiI+Xu/sZEHns6KvMTSE11Aw3uk+yhHxYtZbzWi2B5Nk+4tBdsOxF
PAZdZ5qsyuEcBw+PyfbyZIHWOrlbvZkrmjiIsMJo63cIXuOtgraCjvRRAwe/ZwoU
PXgPcUmrlAs06WjKhuQAZWt6bww7cEP2XyOYlDqwZ4Vj0dqav6g=
=187C
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The memory at the end of the controller only accepts 32bit read/write
accesses, but the arm64 memcpy_to/fromio implementation only uses 64bit
(which will be split into two 32bit access) and 8bit leading to incomplete
copies to/from this memory when the buffer is not multiple of 8bytes.
Add a local copy using writel/readl accesses to make sure we use the right
memory access width.
The switch to memcpy_to/fromio was done because of 285133040e
("arm64: Import latest memcpy()/memmove() implementation"), but using memcpy
worked before since it mainly used 32bit memory acceses.
Fixes: 103a5348c2 ("mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210928073652.434690-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Datasheet specifies that at the end of calibration the SDMMC_CALCR_EN
bit will be cleared. No commands should be send before calibration is
done.
Fixes: dbdea70f71 ("mmc: sdhci-of-at91: fix CALCR register being rewritten")
Fixes: 727d836a37 ("mmc: sdhci-of-at91: add DT property to enable calibration on full reset")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210924082851.2132068-2-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Old SDHI instances have a default value for the reset register which
keeps it in reset state by default. So, when applying a hard reset we
need to manually leave the soft reset state as well. Later SDHI
instances have a different default value, the one we write manually now.
Fixes: b4d86f37ea ("mmc: renesas_sdhi: do hard reset if possible")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826082107.47299-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The fault injection function can set EVENT_DATA_ERROR but skip the
setting of ->data_status to an error status if it hits just after a data
over interrupt. This confuses the tasklet which can later end up
triggering the WARN_ON(host->cmd || ..) in dw_mci_request_end() since
dw_mci_data_complete() would return success.
Prevent the fault injection function from doing this since this is not a
real case, and ensure that the fault injection doesn't race with a real
error either.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fixes: 2b8ac062f3 ("mmc: dw_mmc: Add data CRC error injection")
Link: https://lore.kernel.org/r/20210825114213.7429-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge misc updates from Andrew Morton:
"173 patches.
Subsystems affected by this series: ia64, ocfs2, block, and mm (debug,
pagecache, gup, swap, shmem, memcg, selftests, pagemap, mremap,
bootmem, sparsemem, vmalloc, kasan, pagealloc, memory-failure,
hugetlb, userfaultfd, vmscan, compaction, mempolicy, memblock,
oom-kill, migration, ksm, percpu, vmstat, and madvise)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (173 commits)
mm/madvise: add MADV_WILLNEED to process_madvise()
mm/vmstat: remove unneeded return value
mm/vmstat: simplify the array size calculation
mm/vmstat: correct some wrong comments
mm/percpu,c: remove obsolete comments of pcpu_chunk_populated()
selftests: vm: add COW time test for KSM pages
selftests: vm: add KSM merging time test
mm: KSM: fix data type
selftests: vm: add KSM merging across nodes test
selftests: vm: add KSM zero page merging test
selftests: vm: add KSM unmerge test
selftests: vm: add KSM merge test
mm/migrate: correct kernel-doc notation
mm: wire up syscall process_mrelease
mm: introduce process_mrelease system call
memblock: make memblock_find_in_range method private
mm/mempolicy.c: use in_task() in mempolicy_slab_node()
mm/mempolicy: unify the create() func for bind/interleave/prefer-many policies
mm/mempolicy: advertise new MPOL_PREFERRED_MANY
mm/hugetlb: add support for mempolicy MPOL_PREFERRED_MANY
...
Pages passed to block drivers can be mapped page cache pages, so we must
use flush_dcache_page here instead of the more limited
flush_kernel_dcache_page that is intended for highmem pages only.
Link: https://lkml.kernel.org/r/20210712060928.4161649-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alex Shi <alexs@kernel.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "_kernel_dcache_page fixes and removal".
While looking to convert the block layer away from kmap_atomic towards
kmap_local_page and prefeably the helpers that abstract it away I noticed
that a few block drivers directly or implicitly call
flush_kernel_dcache_page before kunmapping a page that has been written
to.
flush_kernel_dcache_page is documented to to be used in such cases, but
flush_dcache_page is actually required when the page could be in the page
cache and mapped to userspace, which is pretty much always the case when
kmapping an arbitrary page. Unfortunately the documentation doesn't
exactly make that clear, which lead to this misused. And it turns out
that only the copy_strings / copy_string_kernel in the exec code were
actually correct users of flush_kernel_dcache_page, which is why I think
we should just remove it and eat the very minor overhead in exec rather
than confusing poor driver writers.
This patch (of 6):
MIPS now implements flush_kernel_dcache_page (as an alias to
flush_dcache_page).
Link: https://lkml.kernel.org/r/20210712060928.4161649-1-hch@lst.de
Link: https://lkml.kernel.org/r/20210712060928.4161649-2-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Guo Ren <guoren@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Cc: Rich Felker <dalias@libc.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Alex Shi <alexs@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Return a proper response in case of an ioctl error
- Issue HPI to interrupt BKOPS for eMMC if it timed out
- Avoid hogging the CPU while polling for busy
- Extend sd8787 pwrseq to support the wilc1000 SDIO
- Remove a couple of confusing warning messages
- Clarify comment for ->card_busy() host ops
MMC host:
- dw_mmc: Add data CRC error injection
- mmci: De-assert reset during ->probe()
- rtsx_pci: Fix long reads when clock is pre-scaled
- sdhci: Correct the tuning command handle for PIO mode
- sdhci-esdhc-imx: Improve support for auto tuning
- sdhci-msm: Add support for the sc7280
- sdhci-of-arasan: Don't auto tune for DDR50 mode for ZynqMP
- sdhci-of-arasan: Enable support for auto cmd12
- sdhci-of-arasan: Use 19MHz for SD default speed for ZynqMP for level shifter
- usdhi6rol0: Implement the ->card_busy() host ops
MEMSTICK:
- A couple of minor cleanups.
-----BEGIN PGP SIGNATURE-----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=RXpg
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Return a proper response in case of an ioctl error
- Issue HPI to interrupt BKOPS for eMMC if it timed out
- Avoid hogging the CPU while polling for busy
- Extend sd8787 pwrseq to support the wilc1000 SDIO
- Remove a couple of confusing warning messages
- Clarify comment for ->card_busy() host ops
MMC host:
- dw_mmc: Add data CRC error injection
- mmci: De-assert reset during ->probe()
- rtsx_pci: Fix long reads when clock is pre-scaled
- sdhci: Correct the tuning command handle for PIO mode
- sdhci-esdhc-imx: Improve support for auto tuning
- sdhci-msm: Add support for the sc7280
- sdhci-of-arasan: Don't auto tune for DDR50 mode for ZynqMP
- sdhci-of-arasan: Enable support for auto cmd12
- sdhci-of-arasan: Use 19MHz for SD default speed for ZynqMP for level shifter
- usdhi6rol0: Implement the ->card_busy() host ops
MEMSTICK:
- A couple of minor cleanups"
* tag 'mmc-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: queue: Remove unused parameters(request_queue)
mmc: pwrseq: sd8787: fix compilation warning
mmc: core: Return correct emmc response in case of ioctl error
mmc: sdhci-esdhc-imx: Select the correct mode for auto tuning
mmc: sdhci-esdhc-imx: Remove redundant code for manual tuning
mmc: core: Issue HPI in case the BKOPS timed out
mmc: queue: Match the data type of max_segments
mmc: switch from 'pci_' to 'dma_' API
memstick: switch from 'pci_' to 'dma_' API
memstick: r592: Change the name of the 'pci_driver' structure to be consistent
mmc: pwrseq: add wilc1000_sdio dependency for pwrseq_sd8787
mmc: pwrseq: sd8787: add support for wilc1000
dt-bindings: mmc: Extend pwrseq-sd8787 binding for wilc1000
dt-bindings: mmc: fsl-imx-esdhc: change the pinctrl-names rule
dt-bindings: mmc: fsl-imx-esdhc: add a new compatible string
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L bindings
dt-bindings: mmc: renesas,sdhi: Fix dtbs-check warning
mmc: core: Update ->card_busy() callback comment
mmc: usdhi6rol0: Implement card_busy function
mmc: sdhci: Correct the tuning command handle for PIO mode
...
This reverts commit 419dd626e3.
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Fixes: 419dd626e3 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
USDHC hardware auto tuning circuit support check 1/4/8 data lines and cmd
line. Out of reset uSDHC, it default select check 4 data lines and do not
check cmd line. This is incorrect if we use 8 data lines. So need to config
the auto tuning mode according to current bus width.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1629285415-7495-2-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For manual tuning method, already call esdhc_prepare_tuning() config the
necessary registers, so remove the redundant code in esdhc_writew_le() for
SDHCI_HOST_CONTROL2.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1629285415-7495-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When switching card voltage to UHS voltage the mmc framework tries to
check the card busy signal, meaning the card pulling DAT0 line low,
before the switch is made. Drivers that does not implement the card_busy
function will manage to do the switch anyway, but the framework will
print a warning about not being able to verify the voltage signal.
Implement card_busy function.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20210816142314.1168-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If sdhci use PIO mode, and use mmc_send_tuning() to send the tuning
command, system will stuck because of the storm irq of sdhci. For PIO mode,
use mmc_send_tuning(), it will trigger buffer_read_ready interrupt and data
transfer complete interrupt. In current code logic, it will directly
return in sdhci_data_irq, can not call the sdhci_transfer_pio(). So the
buffer_read_ready interrupt storm happen. So for standard tuning method,
need to exclude this case.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628858041-1911-1-git-send-email-haibo.chen@nxp.com
[Ulf: Dropped redundant parenthesis in an expression]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor renesas_sdhi_probe() to avoid increasing numbers of
sdhi_quirks_match[] entry when we add other stable SoCs like
r8a779m*.
Note that the sdhi_quirks_match[] is only needed on
renesas_sdhi_internal_dmac.c so that of_data of
renesas_sdhi_sys_dmac.c keeps as-is.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210729103234.480743-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For dw_mmc, this is probably not currently an issue but is still good to
fix though.
Fixes: 3fc7eaef44 ("mmc: dw_mmc: Add external dma interface support")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures at least if external TI SDMA is ever configured for sdhci.
For other external DMA cases, this is probably not currently an issue but
is still good to fix though.
Fixes: 18e762e3b7 ("mmc: sdhci: add support for using external DMA devices")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210810081644.19353-1-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Qcom SD controller defines the usage of 0xF in data
timeout counter register (0x2E) which is actually a reserved
bit as per specification. This would result in maximum of 21.26 secs
timeout value.
Some SDcard taking more time than 2.67secs (timeout value corresponding
to 0xE) and with that observed data timeout errors.
So increasing the timeout value to max possible timeout.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-3-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce max_timeout_count variable in the sdhci_host structure
and use in timeout calculation. By default its set to 0xE
(max timeout register value as per SDHC spec). But at the same time
vendors drivers can update it if they support different max timeout
register value than 0xE.
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-2-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make 'struct mmc_request' contain a pointer to the request's
'struct bio_crypt_ctx' directly, instead of extracting a 32-bit DUN from
it which is a cqhci-crypto specific detail.
This keeps the cqhci crypto specific details in the cqhci module, and it
makes mmc_core and mmc_block ready for MMC crypto hardware that accepts
the DUN and/or key in a way that is more flexible than that which will
be specified by the eMMC v5.2 standard. Exynos SoCs are an example of
such hardware, as their inline encryption hardware takes keys directly
(it has no concept of keyslots) and supports 128-bit DUNs.
Note that the 32-bit DUN length specified by the standard is very
restrictive, so it is likely that more hardware will support longer DUNs
despite it not following the standard. Thus, limiting the scope of the
32-bit DUN assumption to the place that actually needs it is warranted.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210721154738.3966463-1-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the i.MX conversion to a DT-only platform, the mmc-esdhc-imx.h
header file is no longer used outside the driver, so move its content
to the sdhci-esdhc-imx driver and remove the header.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210719193413.3792615-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver has had problems when handling data errors. Add fault
injection support so that the abort handling can be easily triggered and
regression-tested. A hrtimer is used to indicate a data CRC error at
various points during the data transfer.
Note that for the recent problem with hangs in the case of some data CRC
errors, a udelay(10) inserted at the start of send_stop_abort() greatly
helped in triggering the error, but I've not included this as part of
the fault injection support since it seemed too specific.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210701080534.23138-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Infinite loops are hard to read and understand because of
hidden main loop condition. Simplify such one in mmc_spi_skip().
Using schedule() to schedule (and be friendly to others)
is discouraged and cond_resched() should be used instead.
Hence, replace schedule() with cond_resched() at the same
time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210623101731.87885-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we find a reset handle when probing the MMCI block,
make sure the reset is de-asserted. It could happen that
a hardware has reset asserted at boot.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Yann Gautier <yann.gautier@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20210630102408.3543024-1-linus.walleij@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095734.3046-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'of_property_read_variable_u32_array' function returns number
of elements read on success. This patch updates the condition
check in the driver to overwrite the tap values from DT if exist.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-8-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modify the data type of the clk_phase array to u32 to make it compatible
with the argument requirement of "of_property_read_variable_u32_array".
Addresses-coverity: ("incompatible_param")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-7-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The division macro DIV_ROUND_CLOSEST takes int values as the argument.
However the code here uses unsigned int values for this, which is
causing the values comparison with 0 as always true. We can use
DIV_ROUND_CLOSEST_ULL instead for the same.
Addresses-coverity: ("result_independent_of_operands")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-6-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At a couple of places, the return values of the non-void functions were
not getting checked. This was reported by the coverity tool. Modify the
code to check the return values of the same.
Addresses-Coverity: ("check_return")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ZynqMP platform does not perform auto tuning in DDR50 mode. Skip the
same while the card is operating in DDR50 mode.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Arasan controller supports AUTO CMD12, this patch adds
"SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12" quirk to enable auto cmd12
feature.
By using auto cmd12 we can also avoid following error message
"Got data interrupt even though no data operation in progress"
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD standard speed timing was met only at 19MHz and not 25 MHz, that's
why changing driver to 19MHz. The reason for this is when a level shifter
is used on the board, timing was met for standard speed only at 19MHz.
Since this level shifter is commonly required for high speed modes,
the driver is modified to use standard speed of 19Mhz.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller doesn't seem to pick-up on clock changes, so set the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN flag to query the clock frequency
directly from the clock.
Fixes: f84e411c85 ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1628334401-6577-6-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a known bug on BCM2711's SDHCI core integration where the
controller will hang when the difference between the core clock and the
bus clock is too great. Specifically this can be reproduced under the
following conditions:
- No SD card plugged in, polling thread is running, probing cards at
100 kHz.
- BCM2711's core clock configured at 500MHz or more.
So set 200 kHz as the minimum clock frequency available for that board.
For more information on the issue see this:
https://lore.kernel.org/linux-mmc/20210322185816.27582-1-nsaenz@kernel.org/T/#m11f2783a09b581da6b8a15f302625b43a6ecdeca
Fixes: f84e411c85 ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1628334401-6577-5-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card has not been power cycled, it may still be using 1.8V
signaling. This situation is detected in mmc_sd_init_card function and
should be handled in mmci stm32 variant. The host->pwr_reg variable is
also correctly protected with spin locks.
Fixes: 94b94a93e3 ("mmc: mmci_sdmmc: Implement signal voltage callbacks")
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210701143353.13188-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following fallthrough warning (mips-randconfig with Clang):
drivers/mmc/host/jz4740_mmc.c:792:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/60edca25.k00ut905IFBjPyt5%25lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
This KUnit update for Linux 5.14-rc1 consists of fixes and features:
-- add support for skipped tests
-- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
-- add gnu_printf specifiers
-- add kunit_shutdown
-- add unit test for filtering suites by names
-- convert lib/test_list_sort.c to use KUnit
-- code organization moving default config to tools/testing/kunit
-- refactor of internal parser input handling
-- cleanups and updates to documentation
-- code cleanup related to casts
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPZKym/RZuOCGeA/kCwJExA0NQxwFAmDfNHgACgkQCwJExA0N
QxzU5g/+ORbcbE5jhumo82xYUCGTScgIqPllNO000Vk9xydMqwx6tpY5puV0ig2z
5X7pxKEQTnype58yzY5mS1p336ryIx3q+AwEownxTW3YurXo2naQ59ZPjEvlAV+E
h+DMYLzEjrxzcyJATw02uC9YLUZ3w6FPJfiXViIv93YYrtcnM0u6JpwG0yfBlI4v
4KKB2Xu4K7T90C9/ADFYFKX3mjXQl5fQwvIdtA7wS90Cgq52LKp2mvg1XEiZE5d+
0dkTZ4Zo8TxxHt665o7vfnUjQQNmh45iGlW65wONxfAPb8BPoneGjVKWQTnN0Hor
W+93ZPbMuFMSSKJuoHY9U7sP5VySKvaiIYaGdi6prnZZu0zUabKnLZ6FOy7kEdfs
v09ulCBTVLslixVgNcp/kD9T+G/SXwCF5YBMAiMDQ0GNfUqlFtBkEA3gd44KwMI0
KwCcOgUSiaCkqyzOz/VeQsu/nhA5jdMO0KjiAs7Z3e7r7O/qKFs/ll7hZgDNCWSC
q8eIrcBkSL0EGgXR1iZ4AtGm8op6KKd4ACBM8NdtTyoGFl1npZOgZnHoIsy35G9K
9mhc7eXSoaDGqy9dONL1Tc8Neg7qLTXQNp2radqsnAAgNPUrJuC7+8YC+DdIsjBH
W7OyMjpfbwPws5rP4CS+JdwL+nQprKXZvFIhWGYhkDK44MbOngw=
=5QAv
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit update from Shuah Khan:
"Fixes and features:
- add support for skipped tests
- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
- add gnu_printf specifiers
- add kunit_shutdown
- add unit test for filtering suites by names
- convert lib/test_list_sort.c to use KUnit
- code organization moving default config to tools/testing/kunit
- refactor of internal parser input handling
- cleanups and updates to documentation
- code cleanup related to casts"
* tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
kunit: add unit test for filtering suites by names
kasan: test: make use of kunit_skip()
kunit: test: Add example tests which are always skipped
kunit: tool: Support skipped tests in kunit_tool
kunit: Support skipped tests
thunderbolt: test: Reinstate a few casts of bitfields
kunit: tool: internal refactor of parser input handling
lib/test: convert lib/test_list_sort.c to use KUnit
kunit: introduce kunit_kmalloc_array/kunit_kcalloc() helpers
kunit: Remove the unused all_tests.config
kunit: Move default config from arch/um -> tools/testing/kunit
kunit: arch/um/configs: Enable KUNIT_ALL_TESTS by default
kunit: Add gnu_printf specifiers
lib/cmdline_kunit: Remove a cast which are no-longer required
kernel/sysctl-test: Remove some casts which are no-longer required
thunderbolt: test: Remove some casts which are no longer required
mmc: sdhci-of-aspeed: Remove some unnecessary casts from KUnit tests
iio: Remove a cast in iio-test-format which is no longer required
device property: Remove some casts in property-entry-test
Documentation: kunit: Clean up some string casts in examples
...
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c7 ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
that's just a bunch of data so the diffstat reflects that. Looking beyond that
there's just a bunch of updates all around in various clk drivers. Renesas and
NXP (for i.MX) are two SoC vendors that have a lot of patches in here. Overall
the driver changes look to be mostly enabling more clks and non-critical fixes
that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates clkdev to be
the only implementation of clk_get() and clk_put(). That's a good step in the
right direction to migreate eveerything over to the common clk framework. Now
we don't have to worry about clkdev specific details, they're just part of the
clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is implemented in
only one place in the kernel instead of in drivers/clk/clkdev.c and in
architectures that want their own implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant Clock
Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif, audio,
parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate()
and improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework
-----BEGIN PGP SIGNATURE-----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=YnCF
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round has a diffstat dominated by Qualcomm clk drivers. Honestly
though that's just a bunch of data so the diffstat reflects that.
Looking beyond that there's just a bunch of updates all around in
various clk drivers. Renesas and NXP (for i.MX) are two SoC vendors
that have a lot of patches in here.
Overall the driver changes look to be mostly enabling more clks and
non-critical fixes that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates
clkdev to be the only implementation of clk_get() and clk_put().
That's a good step in the right direction to migreate eveerything over
to the common clk framework. Now we don't have to worry about clkdev
specific details, they're just part of the clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is
implemented in only one place in the kernel instead of in
drivers/clk/clkdev.c and in architectures that want their own
implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant
Clock Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of
round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif,
audio, parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate() and
improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (161 commits)
clk: zynqmp: Handle divider specific read only flag
clk: zynqmp: Use firmware specific mux clock flags
clk: zynqmp: Use firmware specific divider clock flags
clk: zynqmp: Use firmware specific common clock flags
clk: lmk04832: Use of match table
clk: lmk04832: Depend on SPI
clk: stm32mp1: new compatible for secure RCC support
dt-bindings: clock: stm32mp1 new compatible for secure rcc
dt-bindings: reset: add MCU HOLD BOOT ID for SCMI reset domains on stm32mp15
dt-bindings: reset: add IDs for SCMI reset domains on stm32mp15
dt-bindings: clock: add IDs for SCMI clocks on stm32mp15
reset: stm32mp1: remove stm32mp1 reset
clk: hisilicon: Add clock driver for hi3559A SoC
dt-bindings: Document the hi3559a clock bindings
clk: si5341: Add sysfs properties to allow checking/resetting device faults
clk: si5341: Add silabs,iovdd-33 property
clk: si5341: Add silabs,xaxb-ext-clk property
clk: si5341: Allow different output VDD_SEL values
clk: si5341: Update initialization magic
clk: si5341: Check for input clock presence and PLL lock on startup
...
When DMA-mapping of the bounce buffer fails, the driver tries to fall
back, but it leaves the allocated host->bounce_buffer although its
size is zero. Later on, the driver checks the use of bounce buffer
with host->bounce_buffer pointer, and it tries to use the buffer
incorrectly, resulting in Oops.
This patch clears the release the unused buffer and clears the
bounce_buffer pointer for addressing the problem.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210611101948.18972-1-tiwai@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If clock-frequency property is set and it is not the same as the current
clock rate of clk_xin(base clock frequency), set clk_xin to use the
provided clock rate.
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/20210603182242.25733-2-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With KUnit's EXPECT macros no longer typechecking arguments as strictly,
get rid of a number of now unnecessary casts.
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add support for the legacy Arasan sdhci controller on the BCM7211 and
related SoC's. This includes adding a .shutdown callback to increase
the power savings during S5.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20210602192758.38735-2-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has been reported that usage of memcpy() to/from an iomem mapping is invalid,
and a recent arm64 memcpy update [1] triggers a memory abort when dram-access-quirk
is used on the G12A/G12B platforms.
This adds a local sg_copy_to_buffer which makes usage of io versions of memcpy
when dram-access-quirk is enabled.
[1] 285133040e ("arm64: Import latest memcpy()/memmove() implementation")
Fixes: acdc8e71d9 ("mmc: meson-gx: add dram-access-quirk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210609150230.9291-1-narmstrong@baylibre.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the variant on the JZ4775 SoC from Ingenic. Let's also
clarify that the drive clock selection and sample clock selection have been
supported since JZ4775, not X1000. So, support for these two functions has
been added for JZ4775 and JZ4780.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/1623329930-14387-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable support for system wakeup, by setting the wakeup capability for the
slot corresponding to the SDIO card. Users need to enable the wakeup
through the sysfs interface.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1623326486-25275-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'mmc_abort_tuning()' made me think tuning gets completely aborted.
However, it sends only a STOP cmd to cancel the current tuning cmd.
Tuning process may still continue after that. So, rename the function to
'mmc_send_abort_tuning()' to better reflect all this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210608180620.40059-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The card timing and the bus frequency are not changed atomically with
respect to calls to the set_clock() callback in the driver. The result
is the driver sees a transient state where there's a mismatch between
the two and thus the inputs to the phase correction calculation
formula are garbage.
Switch from dev_warn() to dev_dbg() to avoid noise in the normal case,
though the change does make bad configurations less likely to be
noticed.
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607013020.85885-1-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_sprd_writew() was defined by never used in sdhci_ops:
drivers/mmc/host/sdhci-sprd.c:134:20: warning: unused function 'sdhci_sprd_writew'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210601095403.236007-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we don't use structure field layout randomization
the manual shuffling can affect some macros, in particular
container_of() against struct of_mmc_spi, which becomes
a no-op when pdata member is the first one in the structure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210528112127.71738-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dev_dbg() in any case prints the device and driver name, no need
to repeat this in (some) messages. Drop duplicates for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210528112127.71738-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of commit 4cdc2ec1da ("mmc: dw_mmc: move rockchip related code
to a separate file"), dw_mmc-pltfm.c no longer uses the clock API.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210527194226.1705607-1-geert@linux-m68k.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware provides capability configuration registers for each SDHCI
in the global configuration space for the SD controller. Writes to the
global capability registers are mirrored to the capability registers in
the associated SDHCI. Configuration of the capabilities must be written
through the mirror registers prior to initialisation of the SDHCI.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210524073308.9328-5-steven_lee@aspeedtech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the SET_ROM_WAIT_STATES request which erroneously used
usb_rcvctrlpipe().
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133026.17296-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621558965-34077-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621558775-31185-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same calculation to get transfer descriptor offset is already used
at 3 different locations. Let's create a new helper to simplify code.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210521034432.2321-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We already have 'mrq->data' before calling these two functions, no
need to find it again via 'mrq->data' internally. Also remove local
data variable accordingly.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210517100900.1620-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having an indirection through the SDHCI layer and emulating
a capability bit, that isn't there in hardware, do the same same thing
as with HS400_ES and advertise the support for HS400 directly through
the MMC caps.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20210510190400.105162-2-l.stach@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210511093329.4670-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: 75fa9ea6e3 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210508020321.1677-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On the Toshiba Encore 2 WT8-B the microSD slot always reports the card
being write-protected even though microSD cards do not have a write-protect
switch at all.
Add a new DMI_QUIRK_SD_NO_WRITE_PROTECT quirk entry to sdhci-acpi.c's
DMI quirk table for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210503092157.5689-1-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
disable_irq() after request_irq() still has a time gap in which interrupts
can come. request_irq() with IRQF_NO_AUTOEN flag will disable IRQ
auto-enable because of requesting.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1617765339-28946-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This option is now synonymous with CONFIG_HAVE_CLK, so use
the latter globally. Any out-of-tree platform ports that
still use a private clk_get()/clk_put() implementation should
move to CONFIG_COMMON_CLK.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
R-Car M3-W ES3.0 is marketed as R-Car M3-W+ (R8A77961), and has its own
compatible value "renesas,r8a77961".
Hence using soc_device_match() with soc_id = "r8a7796" and revision =
"ES3.*" does not actually match running on an R-Car M3-W+ SoC.
Fix this by matching with soc_id = "r8a77961" instead.
Fixes: a38c078fea ("mmc: renesas_sdhi: Avoid bad TAP in HS400")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/ee8af5d631f5331139ffea714539030d97352e93.1622811525.git.geert+renesas@glider.be
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have to bring the eMMC from sending-data state back to transfer state
once we detected a CRC error (timeout) during tuning. So, send a stop
command via mmc_abort_tuning().
Fixes: 4f11997773 ("mmc: tmio: Add tuning support")
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210602073435.5955-1-wsa+renesas@sang-engineering.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Inserting an SD-card on an Intel NUC10i3FNK4 (which contains a GL9755)
results in the message:
mmc0: 1.8V regulator output did not become stable
Following this message, some cards work (sometimes), but most cards fail
with EILSEQ. This behaviour is observed on Debian 10 running kernel
4.19.188, but also with 5.8.18 and 5.11.15.
The driver currently waits 5ms after switching on the 1.8V regulator for
it to become stable. Increasing this to 10ms gets rid of the warning
about stability, but most cards still fail. Increasing it to 20ms gets
some cards working (a 32GB Samsung micro SD works, a 128GB ADATA
doesn't). At 50ms, the ADATA works most of the time, and at 100ms both
cards work reliably.
Signed-off-by: Daniel Beer <dlbeer@gmail.com>
Acked-by: Ben Chuang <benchuanggli@gmail.com>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210424081652.GA16047@nyquist.nev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The brcmfmac driver can generate a scatterlist from a skb with each packets
not aligned to the block size. This is not supported by the Amlogic Descriptor
dma engine where each descriptor must match a multiple of the block size.
The sg list is valid, since the sum of the sg buffers is a multiple of the
block size, but we must discard those when in SD_IO_RW_EXTENDED mode since
SDIO block mode can be used under the hood even with data->blocks == 1.
Those transfers are very rare, thus can be replaced by a bounce buffer
without real performance loss.
Fixes: 7412dee9f1 ("mmc: meson-gx: replace WARN_ONCE with dev_warn_once about scatterlist size alignment in block mode")
Cc: stable@vger.kernel.org
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210426175559.3110575-2-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some drivers like ath10k can sometimg give an sg buffer with an offset whose alignment
is not compatible with the Amlogic DMA descriptor engine requirements.
Simply replace with dev_warn_once() to inform user this should be fixed to avoid
degraded performance.
This should be ultimately fixed in ath10k, but since it's only a performance issue
the warning should be removed.
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Cc: stable@vger.kernel.org
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210426175559.3110575-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups.
-----BEGIN PGP SIGNATURE-----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=WL87
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups"
* tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (79 commits)
mmc: block: Issue a cache flush only when it's enabled
memstick: r592: ignore kfifo_out() return code again
mmc: block: Update ext_csd.cache_ctrl if it was written
mmc: mmc_spi: Make of_mmc_spi.c resource provider agnostic
mmc: mmc_spi: Use already parsed IRQ
mmc: mmc_spi: Drop unused NO_IRQ definition
mmc: mmc_spi: Set up polling even if voltage-ranges is not present
mmc: core: Convert mmc_of_parse_voltage() to use device property API
mmc: core: Correct descriptions in mmc_of_parse()
mmc: dw_mmc-rockchip: Just set default sample value for legacy mode
mmc: sdhci-s3c: constify uses of driver/match data
mmc: sdhci-s3c: correct kerneldoc of sdhci_s3c_drv_data
mmc: sdhci-s3c: simplify getting of_device_id match data
mmc: tmio: always restore irq register
mmc: sdhci-pci-gli: Enlarge ASPM L1 entry delay of GL975x
mmc: core: Let eMMC sanitize not retry in case of timeout/failure
mmc: core: Add a retries parameter to __mmc_switch function
memstick: r592: remove unused variable
mmc: sdhci-st: Remove unnecessary error log
mmc: sdhci-msm: Remove unnecessary error log
...
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate
cpufreq driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx
cpufreq driver and drop the CPU PM clock .set_parent method for
armada-37xx (Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values
in cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags()
to avoid issuse in some cases when the device depends on an ACPI
power resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks()
to pm_runtime.h and drop the unused try_to_freeze_nowarn()
definition (YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in
the wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check
during resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to
the new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda).
-----BEGIN PGP SIGNATURE-----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=t+SG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add some new hardware support (for example, IceLake-D idle
states in intel_idle), fix some issues (for example, the handling of
negative "sleep length" values in cpuidle governors), add new
functionality to the existing drivers (for example, scale-invariance
support in the ACPI CPPC cpufreq driver) and clean up code all over.
Specifics:
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate cpufreq
driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx cpufreq
driver and drop the CPU PM clock .set_parent method for armada-37xx
(Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values in
cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags() to
avoid issuse in some cases when the device depends on an ACPI power
resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks() to
pm_runtime.h and drop the unused try_to_freeze_nowarn() definition
(YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in the
wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check during
resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to the
new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda)"
* tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
cpufreq: Kconfig: fix documentation links
PM: wakeup: use dev_set_name() directly
PM: runtime: Add documentation for pm_runtime_resume_and_get()
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration
cpuidle: tegra: Remove do_idle firmware call
cpuidle: tegra: Fix C7 idling state on Tegra114
PM: sleep: fix typos in comments
cpufreq: Remove unused for_each_policy macro
...
SPI core already parses and maps IRQ for us if provided.
Use it instead of double parsing in mmc_spi_get_pdata().
Due to above, change condition, since SPI core can hold
an error pointer as invalid IRQ.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the commit 073350f7b5 ("mmc: mmc_spi: Fix return value evaluation of
irq_of_parse_and_map()") the NO_IRQ is not used anymore, drop it for good.
Fixes: 073350f7b5 ("mmc: mmc_spi: Fix return value evaluation of irq_of_parse_and_map()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When voltage-ranges property is not present the driver assumes that
it is 3.3v (3.2v..3.4v). But at the same time it disallows polling.
Fix that by dropping the comparison to 0 when no property is provided.
While at it, mark voltage-ranges property optional as it was initially.
Fixes: 9c43df5791 ("mmc_spi: Add support for OpenFirmware bindings")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_of_parse() for a few years has been using device property API.
Convert mmc_of_parse_voltage() as well.
At the same time switch users to new API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit e085b51c74 ("mmc: meson-gx: check for scatterlist size alignment in block mode"),
support for SDIO SD_IO_RW_EXTENDED transferts are properly filtered but some driver
like brcmfmac still gives a block sg buffer size not aligned with SDIO block,
triggerring a WARN_ONCE() with scary stacktrace even if the transfer works fine
but with possible degraded performances.
Simply replace with dev_warn_once() to inform user this should be fixed to avoid
degraded performance.
This should be ultimately fixed in brcmfmac, but since it's only a performance issue
the warning should be removed.
Fixes: e085b51c74 ("mmc: meson-gx: check for scatterlist size alignment in block mode")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210416094347.2015896-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
.set_ios() is called from .resume() as well. For SDIO device which sets
keep-power-in-suspend, nothing should be changed after resuming, as well
as sample tuning value, since this value is tuned already. So we should
not overwrite it with the default value.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/1618539454-182170-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver data (struct sdhci_s3c_drv_data) stored in of_device_id
table is allocated as const and used only in const-way. Skip
unnecessary const-away casts and convert all users to work with pointer
to const. This is both more logical and safer.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Correct the name of sdhci_s3c_drv_data structure in kerneldoc:
drivers/mmc/host/sdhci-s3c.c:143: warning:
expecting prototype for struct sdhci_s3c_driver_data. Prototype was for struct sdhci_s3c_drv_data instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_device_get_match_data() to make the code slightly smaller and to
remove the of_device_id table forward declaration.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, only SDHI on R-Car Gen2+ reinitializes the irq register
during reset but it should be done on all instances. We can move it from
the SDHI driver to the TMIO core, because we now have the
'sd_irq_mask_all' variable which carries the proper value to use. That
also means we can remove the initialization from tmio_mmc_probe()
because it calls tmio_mmc_reset(), too. We only move that
tmio_mmc_reset() call there a little to ensure 'sd_irq_mask_all' is
properly set.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210413083137.11171-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL975x enters ASPM L1 state after a short idle in default.
Enlarge the idle period to 7.9us for improving the R/W performance.
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Link: https://lore.kernel.org/r/20210415032637.5219-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull OPP (Operating Performance Points) framework updates for v5.13
from Viresh Kumar:
"This adds devm variants for OPP APIs and updates few of the users
as well (Yangtao Li and Dmitry Osipenko)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
memory: samsung: exynos5422-dmc: Convert to use resource-managed OPP API
drm/panfrost: Convert to use resource-managed OPP API
drm/lima: Convert to use resource-managed OPP API
mmc: sdhci-msm: Convert to use resource-managed OPP API
spi: spi-qcom-qspi: Convert to use resource-managed OPP API
spi: spi-geni-qcom: Convert to use resource-managed OPP API
serial: qcom_geni_serial: Convert to use resource-managed OPP API
opp: Change return type of devm_pm_opp_attach_genpd()
opp: Change return type of devm_pm_opp_register_set_opp_helper()
opp: Add devres wrapper for dev_pm_opp_of_add_table
opp: Add devres wrapper for dev_pm_opp_set_supported_hw
opp: Add devres wrapper for dev_pm_opp_set_regulators
opp: Add devres wrapper for dev_pm_opp_set_clkname
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210409023801.3326572-1-qiulaibin@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jia Yang <jiayang5@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409015424.3277212-1-jiayang5@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20210409023349.3325907-1-qiulaibin@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we got the timeout handling in the driver correct, we can use
this capability to avoid polling via the MMC core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210409094606.4317-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD8 is not supported with Command Queue Enabled. Add required callback
to clear CQE_EN and CQE_INTR fields in the host controller register
before sending CMD8. Add corresponding callback in the CQHCI resume path
to re-enable CQE_EN and CQE_INTR fields.
Reported-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Aniruddha Tvs Rao <anrao@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210407094617.770495-1-jonathanh@nvidia.com
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For GL9763E, although there is the best performance at the maximum delay.
Change the value to 20us in order to have better power consumption.
This change may reduce the maximum performance by 10%.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20210407093816.8863-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/mmc/host/moxart-mmc.c:257:7: warning: variable ‘dma_time’ set
but not used
drivers/mmc/host/moxart-mmc.c:395:7: warning: variable ‘pio_time’ set
but not used
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1617357231-93064-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bus power may control card power, but the full reset done by SDHCI at
initialization still may not reset the power, whereas a direct write to
SDHCI_POWER_CONTROL can. That might be needed to initialize correctly, if
the card was left powered on previously.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210331081752.23621-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As indicated by function esdhc_change_pinstate(), SDR50 and DDR50
require pins_100mhz, while SDR104 and HS400 require pins_200mhz. Some
system design may support SDR50 and DDR50 with 100mhz pin state only
(without 200mhz one). Currently the combined 100/200 MHz pinctrl state
check prevents such system from running SDR50 and DDR50. Separate the
check to support such system design.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20210326110214.28416-1-shawnguo@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the CQHCI_QUIRK_SHORT_TXFR_DESC_SZ quirk because the
latest chips have this fixed and earlier chips have other
CQE problems that prevent the feature from being enabled.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210325192834.42955-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As pointed out by Ulf, "both "mmc->parent" and mmc_dev(mmc) are being
used in the entire c-file". Convert all the mmc->parent usage in all
sdhci host driver to mmc_dev() for consistency.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20210324155013.1e5faa3c@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c2c4da37837e ("mmc: sdhci-of-dwcmshc: add rockchip platform support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210323112956.1016884-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit adds ACPI support in the sdhci-of-dwcmshc driver for
BlueField-3 SoC. It has changes to only use the clock hierarchy
for Deviec Tree since the clk is not supported by ACPI. Instead,
ACPI can define 'clock-frequency' which is parsed by existing
sdhci_get_property(). This clock value will be returned in function
dwcmshc_get_max_clock().
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Link: https://lore.kernel.org/r/1616453211-275165-1-git-send-email-limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After reset, we manually flagged retune in runtime resume, but missed it
in the workqueue. To fix that and avoid the problem in the future, let's
flag retune in the reset handler directly whenever a card is present.
Reported-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resetting the IP core will lose the bus width information and not all
code paths recover it. So, make sure the latest bus width gets restored
in the reset routine. For that, tmio_mmc_set_bus_width() is moved, but
not modified.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This variant is present on a Lenovo IdeaPad Slim 1, which uses an AMD Dali/Athlon Silver 3050e.
The Windows AMD SD Host Controller driver also lists this as a valid device ID.
Adding this device ID makes the internal eMMC storage on the Lenovo accessible.
Consequently this makes Linux installable and usable on it as well.
Signed-off-by: James Young <james@pocketfluff.org>
Link: https://lore.kernel.org/r/20210318124025.3002861-1-james@pocketfluff.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All recent SDHI instances can be reset via the reset controller. If one
is found, use it instead of the open coded reset. This is to get a
future-proof sane reset state.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
renesas_sdhi_reset used to mainly reset the SCC but is now doing more
and even more will be added. So, factor out SCC reset to have a clear
distinction when we want to reset either SCC or SDHI+SCC.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will soon allow resetting the whole IP core via a reset controller.
For this case, DMA must be terminated before the actual reset. For the
other cases, it is probably better, too.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The retrieval of driver data can be a bit simplified by using
device_get_match_data(), so switch to it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210314230824.148969-2-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
i.MX has been converted to a devicetree only platform, so remove
the non-DT stub for sdhci_esdhc_imx_probe_dt().
Also, make the driver depend on OF now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210314230824.148969-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following coccicheck warning:
./drivers/mmc/host/via-sdmmc.c:1274:5-8: Unneeded variable: "ret".
Return "0" on line 1295
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1615272478-52458-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210305090724.18832-1-p.zabel@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210305090827.19124-1-p.zabel@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Populate the new member for custom mask values to make sure this value
is applied whenever needed. Also, rename the define holding the value
because this is not only about initialization anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210304092903.8534-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For data read commands, SDHC may initiate data transfers even before it
completely process the command response. In case command itself fails,
driver un-maps the memory associated with data transfer but this memory
can still be accessed by SDHC for the already initiated data transfer.
This scenario can lead to un-mapped memory access error.
To avoid this scenario, reset SDHC (when command fails) prior to
un-mapping memory. Resetting SDHC ensures that all in-flight data
transfers are either aborted or completed. So we don't run into this
scenario.
Swap the reset, un-map steps sequence in sdhci_request_done().
Suggested-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Pradeep P V K <pragalla@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1614760331-43499-1-git-send-email-pragalla@qti.qualcomm.com
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's odd to adopt different error handling on failure of
pci_read_config_dword(). Check the return value and terminate
execution flow on failure of all pci_read_config_dword() calls
in this function.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210226084146.29095-1-dinghao.liu@zju.edu.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Short circuit protection mechanism of GL9755 is disabled by HW default
setting. Enable short circuit protection to prevent GL9755 from being
damaged by short circuit or over current.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210225111307.62975-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When imx_data->pinctrl is not a valid pointer, pinctrl_lookup_state
will trigger kernel panic.
When we boot Dual OS on Jailhouse hypervisor, we let the 1st Linux to
configure pinmux ready for the 2nd OS, so the 2nd OS not have pinctrl
settings.
Similar to this commit b62eee9f80 ("mmc: sdhci-esdhc-imx: no fail when no pinctrl available").
Reviewed-by: Bough Chen <haobo.chen@nxp.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1614222604-27066-6-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHI Gen2+ has a different value for TMIO_MASK_ALL, so add a member to
support that. If the member is not used, the previous default value is
applied.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210223100830.25125-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A 'tmio_mmc_host_free()' call is missing in the remove function, in order
to balance a 'tmio_mmc_host_alloc()' call in the probe.
This is done in the error handling path of the probe, but not in the remove
function.
Add the missing call.
Fixes: 3fd784f745 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142953.918608-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A 'uniphier_sd_clk_enable()' call should be balanced by a corresponding
'uniphier_sd_clk_disable()' call.
This is done in the remove function, but not in the error handling path of
the probe.
Add the missing call.
Fixes: 3fd784f745 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142935.918554-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RPM handling has been improved twice since this comment, and also SCC
handling has been improved a lot. All the testing we did (Geert's and
Niklas' and Wolfram's board farms) with the workaround removed did not
lead to problems, so it is time to get rid of it to the best of our
knowledge.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210218110224.6910-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->card_event callback isn't being used by any of the dw_mmc variants.
It's likely a leftover from an earlier change, hence let's just drop the
redundant call to it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use resource-managed OPP API to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
An issue has been observed on STM32MP157C-EV1 board, with an erase command
with secure erase argument, ending up waiting for ~4 hours before timeout.
The requested busy timeout from the mmc core ends up with 14784000ms (~4
hours), but the supported host->max_busy_timeout is 86767ms, which leads to
that the core switch to use an R1 response in favor of the R1B and polls
for busy with the host->card_busy() ops. In this case the polling doesn't
work as expected, as we never detects that the card stops signaling busy,
which leads to the following message:
mmc1: Card stuck being busy! __mmc_poll_for_busy
The problem boils done to that the stm32 variants can't use R1 responses in
favor of R1B responses, as it leads to an internal state machine in the
controller to get stuck. To continue to process requests, it would need to
be reset.
To fix this problem, let's set MMC_CAP_NEED_RSP_BUSY for the stm32 variant,
which prevent the mmc core from switching to R1 responses. Additionally,
let's cap the cmd->busy_timeout to the host->max_busy_timeout, thus rely on
86767ms to be sufficient (~66 seconds was need for this test case).
Fixes: 94fe2580a2 ("mmc: core: Enable erase/discard/trim support for all mmc hosts")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20210225145454.12780-1-yann.gautier@foss.st.com
Cc: stable@vger.kernel.org
[Ulf: Simplified the code and extended the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"Two memory encryption related patches (SWIOTLB is enabled by default
for AMD-SEV):
- Add support for alignment so that NVME can properly work
- Keep track of requested DMA buffers length, as underlaying hardware
devices can trip SWIOTLB to bounce too much and crash the kernel
And a tiny fix to use proper APIs in drivers"
* 'stable/for-linus-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Validate bounce size in the sync/unmap path
nvme-pci: set min_align_mask
swiotlb: respect min_align_mask
swiotlb: don't modify orig_addr in swiotlb_tbl_sync_single
swiotlb: refactor swiotlb_tbl_map_single
swiotlb: clean up swiotlb_tbl_unmap_single
swiotlb: factor out a nr_slots helper
swiotlb: factor out an io_tlb_offset helper
swiotlb: add a IO_TLB_SIZE define
driver core: add a min_align_mask field to struct device_dma_parameters
sdhci: stop poking into swiotlb internals
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
Use the proper API to query the max mapping size instead of guessing
it based on swiotlb internals.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/20210208134551.39696-1-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-10-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-9-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-8-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-7-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-6-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-5-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-4-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-3-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-2-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Add support for testing whether bus voltage level translator is present
and operational. This is useful on systems where the bus voltage level
translator is optional, as the translator can be auto-detected by the
driver and the feedback clock functionality can be disabled if it is
not present.
This requires additional pinmux state, "init", where the CMD, CK, CKIN
lines are not configured, so they can be claimed as GPIOs early on in
probe(). The translator test sets CMD high to avoid interfering with a
card, and then verifies whether signal set on CK is detected on CKIN.
If the signal is detected, translator is present, otherwise the CKIN
feedback clock are disabled.
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210124170258.32862-2-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for Qualcomm Inline Crypto Engine (ICE) to sdhci-msm.
The standard-compliant parts, such as querying the crypto capabilities
and enabling crypto for individual MMC requests, are already handled by
cqhci-crypto.c, which itself is wired into the blk-crypto framework.
However, ICE requires vendor-specific init, enable, and resume logic,
and it requires that keys be programmed and evicted by vendor-specific
SMC calls. Make the sdhci-msm driver handle these details.
This is heavily inspired by the similar changes made for UFS, since the
UFS and eMMC ICE instances are very similar. See commit df4ec2fa7a
("scsi: ufs-qcom: Add Inline Crypto Engine support").
I tested this on a Sony Xperia 10, which uses the Snapdragon 630 SoC,
which has basic upstream support. Mainly, I used android-xfstests
(https://github.com/tytso/xfstests-bld/blob/master/Documentation/android-xfstests.md)
to run the ext4 and f2fs encryption tests in a Debian chroot:
android-xfstests -c ext4,f2fs -g encrypt -m inlinecrypt
These tests included tests which verify that the on-disk ciphertext is
identical to that produced by a software implementation. I also
verified that ICE was actually being used.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-9-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Snapdragon SoCs, the Linux kernel isn't permitted to directly access
the standard CQHCI crypto configuration registers. Instead, programming
and evicting keys must be done through vendor-specific SMC calls.
To support this hardware, add a ->program_key() method to
'struct cqhci_host_ops'. This allows overriding the standard CQHCI
crypto key programming / eviction procedure.
This is inspired by the corresponding UFS crypto support, which uses
these same SMC calls. See commit 1bc726e26e ("scsi: ufs: Add
program_key() variant op").
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-6-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for eMMC inline encryption using the blk-crypto framework
(Documentation/block/inline-encryption.rst).
eMMC inline encryption support is specified by the upcoming JEDEC eMMC
v5.2 specification. It is only specified for the CQ interface, not the
non-CQ interface. Although the eMMC v5.2 specification hasn't been
officially released yet, the crypto support was already agreed on
several years ago, and it was already implemented by at least two major
hardware vendors. Lots of hardware in the field already supports and
uses it, e.g. Snapdragon 630 to give one example.
eMMC inline encryption support is very similar to the UFS inline
encryption support which was standardized in the UFS v2.1 specification
and was already upstreamed. The only major difference is that eMMC
limits data unit numbers to 32 bits, unlike UFS's 64 bits.
Like we did with UFS, make the crypto support opt-in by individual
drivers; don't enable it automatically whenever the hardware declares
crypto support. This is necessary because in every case we've seen,
some extra vendor-specific logic is needed to use the crypto support.
Co-developed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210125183810.198008-5-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the task descriptor initialization into cqhci_prep_task_desc().
In addition, make it explicitly initialize all 128 bits of the task
descriptor if the host controller is using 128-bit task descriptors,
rather than relying on the implicit zeroing from dmam_alloc_coherent().
This is needed to prepare for CQHCI inline encryption support, which
requires 128-bit task descriptors and uses the upper 64 bits.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-4-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename cqhci.c to cqhci-core.c so that another source file can be added
to the cqhci module without having to rename the module.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-3-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Randy found that with the following Kconfig settings we have duplicate
definitions (e.g. __inittest()) in sdhci-of-aspeed due to competing
module_init()/module_exit() calls from kunit and driver the itself.
```
CONFIG_MMC_SDHCI_OF_ASPEED=m
CONFIG_MMC_SDHCI_OF_ASPEED_TEST=y
```
Conditionally open-code the kunit initialisation to avoid the error.
Fixes: 7efa02a981d6 ("mmc: sdhci-of-aspeed: Add KUnit tests for phase calculations")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20210122114852.3790565-1-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120142801.334550-3-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120142801.334550-2-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RPi4 has an Arasan controller it carries over from the RPi3 and a newer
eMMC2 controller. Because of a couple of quirks, it seems wiser to bind
these controllers to the same driver that DT is using on this platform
rather than the generic sdhci_acpi driver with PNP0D40.
So, BCM2847 describes the older Arasan and BRCME88C describes the newer
eMMC2. The older Arasan is reusing an existing ACPI _HID used by other OSes
booting these tables on the RPi.
With this change, Linux is capable of utilizing the SD card slot, and the
Wi-Fi when booted with UEFI+ACPI on the RPi4.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120000406.1843400-2-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Converting degrees of phase to logic delays is irritating to test on
hardware, so lets exercise the function using KUnit.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-5-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The AST2600 can achieve HS200 speeds with a change to the bus clock
divisor behaviour. The divisor can also be more accurate with respect
to the requested clock rate, but keep the one-hot behaviour for
backwards compatibility with the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-4-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Aspeed SD/eMMC controllers expose configurable clock phase
correction by inserting delays of up to 15 logic elements in length into
the bus clock path. The hardware supports independent configuration for
both bus directions on a per-slot basis.
The timing delay per element encoded in the driver was experimentally
determined by scope measurements.
The phase controls for both slots are grouped together in a single
register of the global register block of the SD/MMC controller(s), which
drives the use of a locking scheme between the SDHCIs and the global
register set.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-3-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following coccicheck warning:
./drivers/mmc/host/omap_hsmmc.c:297:6-25: WARNING: Comparison of 0/1 to
bool variable
According to the context, vqmmc_enabled is more suitable for bool type.
Reported-by: Abaci Robot<abaci@linux.alibaba.com>
Signed-off-by: Yang Li <abaci-bugfix@linux.alibaba.com>
Link: https://lore.kernel.org/r/1610704281-11036-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
