commit 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled the internal clocks depending on the
subnodes that are populated in device tree. However recent discussions
in the mailing list [1] suggested to just add #clock cells in the parent
DT node and model the clocks within the driver.
Model the mux clocks without device tree input for AM64x SoC. Don't
remove the earlier design since DT nodes for J7200 and J721e are already
upstreamed.
[1] -> http://lore.kernel.org/r/20210108025943.GA1790601@robh.at.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-5-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The frequency of the txmclk between PCIe and SERDES has
changed to 250MHz from 500MHz. Configure full rate divider
for AM64 accordingly.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-4-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
commit 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled both MUX clocks and DIVIDER clocks in
wiz. However during cleanup, it removed only the MUX clock provider.
Remove the DIVIDER clock provider here.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Both "struct wiz_clk_div_sel" and "struct wiz_clk_mux_sel" are static
data that is common for all wiz instances. Including
"struct regmap_field" for each of the wiz instances can yield undesirable
results. Move "struct regmap_field" out of "struct wiz_clk_div_sel" and
"struct wiz_clk_mux_sel" and make them point to constant data.
So far no issues are observed since both these structures are not
accessed outside the probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-2-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Marvell CP110 UTMI PHY driver allowing the USB2
port configuration independently from the boot loader setup.
The CP110/CP115 dies have 2 UTMI PHYs that could be connected
to two USB host controllers or to single USB device controller.
Since there is only one USB device controller on die, only one
of the UTMI PHYs could work in USB device mode.
The CONFIG_PHY_MVEBU_CP110_UTMI should be enabled for usage of
this driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20210307163343.25684-2-kostap@marvell.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Provide new phy configuration interfaces for media type and speed that
allows e.g. PHYs used for ethernet to be configured with this
information.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210218161451.3489955-3-steen.hegelund@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix OF node leaks by calling of_node_put in
for_each_child_of_node when the cycle returns.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210216082739.1414-1-angkery@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix OF node leaks by calling of_node_put in
for_each_available_child_of_node when the cycle returns.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210216084847.1544-1-angkery@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
ck_usbo_48m is generated by usbphyc PLL and used by OTG controller
for Full-Speed use cases with dedicated Full-Speed transceiver.
ck_usbo_48m is available as soon as the PLL is enabled.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210208114659.15269-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Start by reading the content of the VENDOR_SPECIFIC2 register and update
each bit field based on device properties when defined.
The use of bit masks prevents fields from overriding each other and
enables users to clear bits which are set by default, like datapolarity
in this instance.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20201211191241.21306-1-liambeguin@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Updates:
- Conversion to YAML binding for:
- mtk-xsphy
- mtk-tphy
- mtk-ufs
- HDMI PHY
- MIPI DSI PHY
- brcmstb-usb-phy
- Support for BCM4908 usb phy
- Support for Qualcomm SDX55 USB and QMP phy
- Support for Qualcomm SM8350 aka Snapdragon 888 UFS and USB phy
- Support for Qualcomm SDM660 USB and UFS phy
- Support for Qualcomm SC8180X USB and UFS phy
- Support for Qualcomm IPQ6018 USB phy
- Stm32 phy updates
-----BEGIN PGP SIGNATURE-----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=kOAq
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.12
- Updates:
- Conversion to YAML binding for:
- mtk-xsphy
- mtk-tphy
- mtk-ufs
- HDMI PHY
- MIPI DSI PHY
- brcmstb-usb-phy
- Support for BCM4908 usb phy
- Support for Qualcomm SDX55 USB and QMP phy
- Support for Qualcomm SM8350 aka Snapdragon 888 UFS and USB phy
- Support for Qualcomm SDM660 USB and UFS phy
- Support for Qualcomm SC8180X USB and UFS phy
- Support for Qualcomm IPQ6018 USB phy
- Stm32 phy updates
* tag 'phy-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (41 commits)
phy: cpcap-usb: Simplify bool conversion
phy: qcom-qmp: make a const array static, makes object smaller
phy: zynqmp: Simplify code by using dev_err_probe()
phy: qcom-qmp: Add support for SM8350 UFS phy
phy: qcom-qmp: Add UFS V5 registers found in SM8350
dt-bindings: phy: qcom,qmp: Add SM8350 UFS PHY bindings
phy: qualcomm: usb28nm: Add MDM9607 init sequence
dt-bindings: phy: qcom,qusb2: document ipq6018 compatible
phy: qcom-qusb2: add QUSB2 support for IPQ6018
phy: qcom-qmp: Add SC8180X USB phy
phy: qcom-qmp: Add SC8180X UFS phy
dt-bindings: phy: qcom,qmp: Add SC8180X USB phy
dt-bindings: phy: qcom,qmp: Add SC8180X UFS to the QMP binding
dt-bindings: phy: qcom-qusb2: Document SDM660 compatible
phy: qcom-qusb2: Add configuration for SDM660
phy: qcom-qusb2: Allow specifying default clock scheme
dt-bindings: phy: qcom,usb-snps-femto-v2: Add SM8250 and SM8350 bindings
phy: qcom-qmp: Add SM8350 USB QMP PHYs
dt-bindings: phy: qcom,qmp: Add SM8150, SM8250 and SM8350 USB PHY bindings
phy: qcom-qmp: Add support for SDX55 QMP PHY
...
Fix the following coccicheck warning:
./drivers/phy/motorola/phy-cpcap-usb.c:146:31-36: WARNING: conversion to
bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1611905915-50394-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Don't populate the const array cfg1_settings on the stack but instead make
it static. Makes the object code smaller by 24 bytes:
Before:
text data bss dec hex filename
73585 20240 64 93889 16ec1 drivers/phy/qualcomm/phy-qcom-qmp.o
After:
text data bss dec hex filename
73465 20336 64 93865 16ea9 drivers/phy/qualcomm/phy-qcom-qmp.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210204180313.108876-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the registers for UFS found in SM8350. The UFS phy used in SM8350
seems to have same offsets as V5 phy, although Documentation for that is
lacking.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210204165805.62235-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds the missing MODULE_DEVICE_TABLE definitions on different
Mediatek phy drivers which generates correct modalias for automatic loading
when these drivers are compiled as an external module.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210203110631.686003-1-enric.balletbo@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Intel Lightning Mountain (LGM) USB3 USB is only present on Intel
Lightning Mountain SoCs. Hence add a dependency on X86, to prevent
asking the user about this driver when configuring a kernel without
Intel Lightning Mountain platform support.
Fixes: 1cce8f73a5 ("phy: Add USB3 PHY support for Intel LGM SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210129131753.2656306-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Qualcomm SC8180X has two QMP phys used for SuperSpeed USB, which are
either the same or very similar to the same found in SM8150. Add a
compatible for this, reusing the existing SM8150 USB phy config.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210121014339.1612525-2-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The UFS phy found in the Qualcomm SC8180X is either the same or very
similar to the phy present in SM8150, so add a compatible and reuse the
SM8150 configuration.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210120224531.1610709-2-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SDM660 SoC uses the same configuration as MSM8996, but the
clock scheme uses a differential reference clock and none of
the SoCs in this series (630, 636 and others) have got a usable
PHY_CLK_SCHEME register in the TCSR for clk scheme detection.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114174718.398638-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The TCSR's PHY_CLK_SCHEME register is not available on all SoC
models, but some may still use a differential reference clock.
In preparation for these SoCs, add a se_clk_scheme_default
configuration entry and declare it to true for all currently
supported SoCs (retaining the previous defaults.
This patch brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114174718.398638-1-angelogioacchino.delregno@somainline.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the USB DP & UNI PHYs found on SM8350. These use
version 5.0.0 of the QMP PHY IP and thus require new "V5"
definitions of the register offset macros for the QSERDES RX
and TX blocks. The QSERDES common and QPHY PCS blocks' register
offsets are largely unchanged from V4 so some of the existing
macros can be reused.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210115174723.7424-3-jackp@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for USB3 QMP PHY found in SDX55 platform. SDX55 uses
version 4.0.0 of the QMP PHY IP and doesn't make use of "com_aux" clock.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210111113010.32056-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
USBPHYC has a register per phy to control and monitor the debug interface
of the HS PHY through a digital debug access.
With this register, it is possible to know if PLL Lock input to phy is
high. That means the PLL is ready for HS operation.
Instead of using an hard-coded delay after PLL enable and PLL disable, use
this bit to ensure good operating of the HS PHY.
Also use an atomic counter (n_pll_cons) to count the actual number of PLL
consumers and get rid of stm32_usbphyc_has_one_phy_active.
The boolean active in the usbphyc_phy structure is kept, because we need to
know in remove if a phy_exit is required to properly disable the PLL.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-7-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To ensure a good balancing of regulators, and allow PLL disabling when the
driver is removed, call stm32_usbphyc_phy_exit on each ports to set phys
inactive and disable PLL.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-6-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To ensure a good balancing of regulators, force PLL disable either by
reset or by clearing the PLLEN bit.
If waiting the powerdown pulse delay isn't enough, return -EPROBE_DEFER
instead of polling the PLLEN bit, which will be low at the next probe.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Due to async_schedule_domain call in regulator_bulk_enable,
scheduling while atomic bug can raise if regulator_bulk_enable is called
under atomic context.
To avoid this issue, this patch replaces all regulator_bulk* by regulator_
per regulators.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PLL block requires to be powered with 1v1 and 1v8 supplies to catch
ENABLE signal.
Currently, supplies are managed through phy_ops .power_on/off, and PLL
activation/deactivation is managed through phy_ops .init/exit.
The sequence of phy_ops .power_on/.phy_init, .power_off/.exit is USB
drivers dependent.
To ensure a good behavior of the PLL, supplies have to be managed at PLL
activation/deactivation. That means the supplies need to be put in usbphyc
node and not in phy children nodes.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
BCM4908 seems to have slightly different registers but works when
programmed just like the STB one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210106205838.10964-3-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the following sparse warning:
drivers/phy/mediatek/phy-mtk-mipi-dsi.c:237:24: warning: symbol 'mtk_mipi_tx_driver' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1610415484-92497-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 65dc2e7252 ("usb: dwc2: Update Core Reset programming flow.")
revealed that the phy isn't ready immediately after enabling it's
clocks. The dwc2_check_core_version() fails and the dwc2 usb driver
errors out.
Add a short delay to let the phy get up and running. There isn't any
documentation how much time is required, the value was chosen based on
tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <stable@vger.kernel.org> # v5.7+
Link: https://lore.kernel.org/r/20210107224901.2102479-1-dev@kresin.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove the useless field .version from the private structure, which is
set but never read.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20201223124505.40792-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This error path should return -EINVAL, but currently it returns
success.
Fixes: d09945eaca ("phy: cadence-torrent: Check total lane count for all subnodes is within limit")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X9s7Wxq+b6ls0q7o@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is slightly cleaner solution that assures noone assings a wrong
function to the pointer.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201216143305.12179-2-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
1. Use of_device_get_match_data() helper to simplify the code
2. Check for NULL as a good practice
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201216143305.12179-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update the implementation add "rockchip," vendor prefix for the
optional dts properties. Prefix referred from vendor-prefixes.yaml.
Follow up with
commit 8b5c2b45b8 ("phy: rockchip: set pulldown for strobe line in dts")
commit a8cef92827 ("phy: rockchip-emmc: output tap delay dt property")
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20201215014409.905-3-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
rockchip_emmc_phy_init() return variable is not set with the error value
if clk_get() failed. 'emmcclk' is optional, thus use clk_get_optional()
and if the return value != NULL make error processing and set the
return code accordingly.
Fixes: 52c0624a10 phy: rockchip-emmc: Set phyctrl_frqsel based on card clock
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201210080454.17379-1-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Randconfig builds show another broken dependency:
WARNING: unmet direct dependencies detected for PHY_MTK_MIPI_DSI
Depends on [n]: ARCH_MEDIATEK [=n] && OF [=y]
Selected by [m]:
- DRM_MEDIATEK [=m] && HAS_IOMEM [=y] && DRM [=m] && (ARCH_MEDIATEK [=n] || ARM [=y] && COMPILE_TEST [=y]) && COMMON_CLK [=y] &&
HAVE_ARM_SMCCC [=y] && OF [=y] && MTK_MMSYS [=y]
This is similar to the hdmi driver I fixed earlier, and I guess the
common-clk bug would sooner or later also manifest here, so just use
the exact same solution I chose for the other driver, and hope that
any future drivers just copy it from here.
Fixes: 90f80d9599 ("phy: mediatek: Move mtk_mipi_dsi_phy driver into drivers/phy/mediatek folder")
Fixes: f5f6e01f91 ("phy: mediatek: allow compile-testing the hdmi phy")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210103135524.3678664-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On deferred probe, we will get the following splat:
cpcap-usb-phy cpcap-usb-phy.0: could not initialize VBUS or ID IIO: -517
WARNING: CPU: 0 PID: 21 at drivers/regulator/core.c:2123 regulator_put+0x68/0x78
...
(regulator_put) from [<c068ebf0>] (release_nodes+0x1b4/0x1fc)
(release_nodes) from [<c068a9a4>] (really_probe+0x104/0x4a0)
(really_probe) from [<c068b034>] (driver_probe_device+0x58/0xb4)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201230102105.11826-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
