This patch makes copro_calculate_slb() mask the ESID by the correct mask
for 1T vs 256M segments.
This has no effect by itself as the extra bits were ignored, but it
makes debugging the segment table entries easier and means that we can
directly compare the ESID values for duplicates without needing to worry
about masking in the comparison.
This will be used to simplify a comparison in the following patch.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the segment table hash calculation from cxl_load_segment()
into find_free_sste() since that is the only place it is actually used.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch simplifies the process of finding a free segment table entry
by disabling the secondary hash. This reduces the number of possible
entries in the segment table for a given address from 16 to 8.
Due to the large segment sizes we use it is extremely unlikely that the
secondary hash would ever have been used in practice, so this should not
have any negative impacts and may even improve performance due to the
reduced number of comparisons that software & hardware need to perform.
This patch clears the SC bit in the hardware's state register
(CXL_PSL_SR_An) to disable the secondary hash in the hardware since we
can no longer fill out entries using it.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit bf7588a085.
Ben says although the code is not correct "[this] fix was completely
wrong and does more damages than it fixes things."
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we can't call opal wrappers from modules when using the LE
ABIv2, which requires a TOC init. If we do we'll try and load the opal
entry point using the wrong toc and probably explode or worse jump to
the wrong address.
Nothing in upstream is making opal calls from a module, but we do export
one of the wrappers so we should fix this anyway.
This change uses the _GLOBAL_TOC() macro (rather than _GLOBAL) for the
opal wrappers, so that we can do non-local calls to them.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch wires up the new syscall sys_bpf() on powerpc.
Passes the tests in samples/bpf:
#0 add+sub+mul OK
#1 unreachable OK
#2 unreachable2 OK
#3 out of range jump OK
#4 out of range jump2 OK
#5 test1 ld_imm64 OK
#6 test2 ld_imm64 OK
#7 test3 ld_imm64 OK
#8 test4 ld_imm64 OK
#9 test5 ld_imm64 OK
#10 no bpf_exit OK
#11 loop (back-edge) OK
#12 loop2 (back-edge) OK
#13 conditional loop OK
#14 read uninitialized register OK
#15 read invalid register OK
#16 program doesn't init R0 before exit OK
#17 stack out of bounds OK
#18 invalid call insn1 OK
#19 invalid call insn2 OK
#20 invalid function call OK
#21 uninitialized stack1 OK
#22 uninitialized stack2 OK
#23 check valid spill/fill OK
#24 check corrupted spill/fill OK
#25 invalid src register in STX OK
#26 invalid dst register in STX OK
#27 invalid dst register in ST OK
#28 invalid src register in LDX OK
#29 invalid dst register in LDX OK
#30 junk insn OK
#31 junk insn2 OK
#32 junk insn3 OK
#33 junk insn4 OK
#34 junk insn5 OK
#35 misaligned read from stack OK
#36 invalid map_fd for function call OK
#37 don't check return value before access OK
#38 access memory with incorrect alignment OK
#39 sometimes access memory with incorrect alignment OK
#40 jump test 1 OK
#41 jump test 2 OK
#42 jump test 3 OK
#43 jump test 4 OK
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
[mpe: test using samples/bpf]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change maintainer of nx-842 compression coprocessor driver
to Dan Streetman.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the check of CONFIG_PPC_SUBPAGE_PROT when deciding if
is_hugepage_only_range() is extern or inline. The extern version is in
slice.c and is built if CONFIG_PPC_MM_SLICES=y.
There was no build break possible because CONFIG_PPC_SUBPAGE_PROT is
only selectable under conditions which also mean CONFIG_PPC_MM_SLICES
will be selected.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch/powerpc/mm/slice.c:704:5: error: expected identifier or ‘(’ before numeric constant
int is_hugepage_only_range(struct mm_struct *mm, unsigned long addr,
^
make[1]: *** [arch/powerpc/mm/slice.o] Error 1
make: *** [arch/powerpc/mm/slice.o] Error 2
This got introduced via 1217d34b53
"powerpc: Ensure global functions include their prototype". We
started including linux/hugetlb.h with that patch and now we have
#define is_hugepage_only_range(mm, addr, len) 0
with hugetlbfs disabled.
Fixes: 1217d34b53 ("powerpc: Ensure global functions include their prototype")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target updates for v3.18-rc2 code. These where
originally destined for -rc1, but due to the combination of travel
last week for KVM Forum and my mistake of taking the three week merge
window literally, the pull request slipped.. Apologies for that.
Things where reasonably quiet this round. The highlights include:
- New userspace backend driver (target_core_user.ko) by Shaohua Li
and Andy Grover
- A number of cleanups in target, iscsi-taret and qla_target code
from Joern Engel
- Fix an OOPs related to queue full handling with CHECK_CONDITION
status from Quinn Tran
- Fix to disable TX completion interrupt coalescing in iser-target,
that was causing problems on some hardware
- Fix for PR APTPL metadata handling with demo-mode ACLs
I'm most excited about the new backend driver that uses UIO + shared
memory ring to dispatch I/O and control commands into user-space.
This was probably the most requested feature by users over the last
couple of years, and opens up a new area of development + porting of
existing user-space storage applications to LIO. Thanks to Shaohua +
Andy for making this happen.
Also another honorable mention, a new Xen PV SCSI driver was merged
via the xen/tip.git tree recently, which puts us now at 10 target
drivers in upstream! Thanks to David Vrabel + Juergen Gross for their
work to get this code merged"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
target/file: fix inclusive vfs_fsync_range() end
iser-target: Disable TX completion interrupt coalescing
target: Add force_pr_aptpl device attribute
target: Fix APTPL metadata handling for dynamic MappedLUNs
qla_target: don't delete changed nacls
target/user: Recalculate pad size inside is_ring_space_avail()
tcm_loop: Fixup tag handling
iser-target: Fix smatch warning
target/user: Fix up smatch warnings in tcmu_netlink_event
target: Add a user-passthrough backstore
target: Add documentation on the target userspace pass-through driver
uio: Export definition of struct uio_device
target: Remove unneeded check in sbc_parse_cdb
target: Fix queue full status NULL pointer for SCF_TRANSPORT_TASK_SENSE
qla_target: rearrange struct qla_tgt_prm
qla_target: improve qlt_unmap_sg()
qla_target: make some global functions static
qla_target: remove unused parameter
target: simplify core_tmr_abort_task
target: encapsulate smp_mb__after_atomic()
...
Pull mailbox framework from Jassi Brar:
"A framework for Mailbox controllers and clients have been cooking for
more than a year now.
Everybody in the CC list had been copied on patchset revisions and
most of them have made sounds of approval, though just one concrete
Reviewed-by. The patchset has also been in linux-next for a couple of
weeks now and no conflict has been reported. The framework has the
backing of at least 5 platforms, though I can't say if/when they
upstream their drivers (some businesses have 'changed')"
(Further acked-by by Arnd Bergmann and Suman Anna in the pull request
thread)
* 'mailbox-for-linus' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt: mailbox: add generic bindings
doc: add documentation for mailbox framework
mailbox: Introduce framework for mailbox
mailbox: rename pl320-ipc specific mailbox.h
Pull LED update from Bryan Wu:
"Basically we have some bug fixing and clean up and one big thing is we
start to merge patch to add support LED Flash class"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: gpio: cleanup the leds-gpio driver
led: gpio: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
led: gpio: Sort include headers alphabetically
leds: Improve and export led_update_brightness
leds: trigger: gpio: fix warning in gpio trigger for gpios whose accessor function may sleep
leds: lp3944: fix sparse warning
leds: avoid using DEVICE_ATTR macro for max_brightness attribute
leds: make brightness type consistent across whole subsystem
leds: Reorder include directives
There are no new drivers here, only a couple of fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=llZK
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"There are no new drivers here, only a couple of fixes all over the
place"
* tag 'pwm/for-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Let PWM_CLPS711X depend on HAS_IOMEM
pwm: atmel: Fix calculation of prescale value
pwm: Fix uninitialized warnings in pwm_get()
pwm: rockchip: Allow polarity invert on rk3288
pwm: imx: Avoid sample FIFO overflow for i.MX PWM version2
pwm: imx: Cleanup indentation for register definitions
pwm: imx: Fix the macro MX3_PWMCR_PRESCALER(x) definition
pwm: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
pwm: lpss: make it buildable only on X86
pwm: lpss: use c99 initializers in structures
pwm: lpss: Fix build failure on PowerPC
pwm: lpss: pci: Move to use pcim_enable_device()
pwm: lpss: Properly split driver to parts
pwm: lpss: Add ACPI and PCI IDs for Intel Braswell
pwm: fsl-ftm: Select REGMAP_MMIO
pwm: fsl-ftm: Document 'big-endian' property
pwm: fsl-ftm: Convert to direct regmap API usage
pwm: fsl-ftm: Clean up the code
Updated Boot printing
kgdb update for arc gdb 7.5
Bug fixes (some marked for stable)
More code refactoring/consolidation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=236F
-----END PGP SIGNATURE-----
Merge tag 'arc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Sorry for the late pull request. Current stuff was ready for a while
but I was hoping to squeeze in support for almost ready ARC SDP
platform (and avoid a 2nd pull request), however it seems there are
still some loose ends which warrant more time.
- Platform code reduction/moving-up (TB10X no longer needs any
callbacks)
- updated boot printing
- kgdb update for arc gdb 7.5
- bug fixes (some marked for stable)
- more code refactoring/consolidation"
* tag 'arc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: boot: cpu feature print enhancements
ARC: boot: consolidate cross-checking of h/w and s/w
ARC: unbork FPU save/restore
ARC: remove extraneous __KERNEL__ guards
ARC: Update order of registers in KGDB to match GDB 7.5
ARC: Remove unneeded Kconfig entry NO_DMA
ARC: BUG() dumps stack after @msg (@msg now same as in generic BUG))
ARC: refactoring: reduce the scope of some local vars
ARC: remove gcc mpy heuristics
ARC: RIP @running_on_hw
ARC: Update comments about uncached address space
ARC: rename kconfig option for unaligned emulation
ARC: [nsimosci] Allow "headless" models to boot
ARC: [arcfpga] Get rid of ARC_BOARD_ANGEL4 and ARC_BOARD_ML509
ARC: [arcfpga] Remove more dead code
ARC: [plat*] move code out of .init_machine into common
ARC: [arcfpga] consolidate machine description, DT
ARC: Allow SMP kernel to build/boot on UP-only infrastructure
Pull more powerpc updates from Michael Ellerman:
"Here's some more updates for powerpc for 3.18.
They are a bit late I know, though must are actually bug fixes. In my
defence I nearly cut the top of my finger off last weekend in a
gruesome bike maintenance accident, so I spent a good part of the week
waiting around for doctors. True story, I can send photos if you like :)
Probably the most interesting fix is the sys_call_table one, which
enables syscall tracing for powerpc. There's a fix for HMI handling
for old firmware, more endian fixes for firmware interfaces, more EEH
fixes, Anton fixed our routine that gets the current stack pointer,
and a few other misc bits"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (22 commits)
powerpc: Only do dynamic DMA zone limits on platforms that need it
powerpc: sync pseries_le_defconfig with pseries_defconfig
powerpc: Add printk levels to setup_system output
powerpc/vphn: NUMA node code expects big-endian
powerpc/msi: Use WARN_ON() in msi bitmap selftests
powerpc/msi: Fix the msi bitmap alignment tests
powerpc/eeh: Block CFG upon frozen Shiner adapter
powerpc/eeh: Don't collect logs on PE with blocked config space
powerpc/eeh: Block PCI config access upon frozen PE
powerpc/pseries: Drop config requests in EEH accessors
powerpc/powernv: Drop config requests in EEH accessors
powerpc/eeh: Rename flag EEH_PE_RESET to EEH_PE_CFG_BLOCKED
powerpc/eeh: Fix condition for isolated state
powerpc/pseries: Make CPU hotplug path endian safe
powerpc/pseries: Use dump_stack instead of show_stack
powerpc: Rename __get_SP() to current_stack_pointer()
powerpc: Reimplement __get_SP() as a function not a define
powerpc/numa: Add ability to disable and debug topology updates
powerpc/numa: check error return from proc_create
powerpc/powernv: Fallback to old HMI handling behavior for old firmware
...
Pull s390 updates from Martin Schwidefsky:
"One patch to enable the BPF system call and three more bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uprobes: fix kprobes dependency
s390: wire up bpf syscall
s390/mm: fixing calls of pte_unmap_unlock
s390/hmcdrv: Restrict s390 HMC driver to S390 arch
This patch removes the magic value used for rebooting the board. This
value is useless and leads to a static checker warning as reported by
Dan Carpenter.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
They need HAS_IOMEM, so let them depend on it, the related error (with
allmodconfig under um):
MODPOST 1205 modules
ERROR: "devm_ioremap_resource" [drivers/watchdog/tegra_wdt.ko] undefined!
ERROR: "devm_ioremap_resource" [drivers/watchdog/of_xilinx_wdt.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the watchdog hardware found in A31 and
newer SoCs. This new hardware has registers at different offsets, and
the system reset control has been split out of the "mode" register
into a new "configuration" register.
Differences not supported by this driver include separate interrupt
lines for each watchdog, instead of sharing an interrupt line and
registers with the timer block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for hardware parameters tied to compatible
strings, so similar hardware can reuse the driver.
This will be used to support the newer watchdog found in A31 and
later SoCs. Differences in the new hardware include separate
interrupt lines for each watchdog, and corresponding interrupt
control/status registers. Watchdog control registers were also
slightly rearranged.
Also replace ioread32()/iowrite32() with readl()/writel() in various
places changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the
driver instead of providing the restart in machine desc.
This restart handler function is from the mxc_restart()
in arch/arm/mach-imx/system.c
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDT's BITE_TIME warm-reset behavior can be leveraged as a last
resort mechanism for triggering chip reset. Usually, other restart
methods (such as PS_HOLD) are preferrable for issuing a more complete
reset of the chip. As such, keep the priority of the watchdog notifier
low.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On a lot of Samsung systems the watchdog is responsible for restarting the
system and until now this code was contained in plat-samsung/watchdog-reset.c.
With the introduction of the restart handlers, this code can now move into
driver itself, removing the need for arch-specific code.
Tested on a S3C2442 based GTA02
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now provides an API to trigger a system restart.
Register with it to support restarting the system via. watchdog.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Update the multi_v7_defconfig enabling the watchdog driver for Meson
SoCs.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the watchdog driver for the Amlogic Meson SoCs used also
to reboot the device.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no conflict with rtc/rtc-stmp3xxx.c parent
because modified registers in PM functions of stmp3xxx_rtc_wdt
are different.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver supports the watchdog device inside the DA9063 PMIC.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for the watchdog timer available in Ricoh RN5T618
PMIC. The device supports a programmable expiration time of 1, 8, 32
or 128 seconds.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Exynos7 SoC has a Watchdog for Atlas (A57) cores
This patch adds support for the Atlas watchdog.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Qualcomm Krait Processor Sub-system (KPSS) contains one or more
instances of the WDT. Provide documentation on how to describe these in
the device tree.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the watchdog timer block found in the Krait Processor
Subsystem (KPSS) on the MSM8960, APQ8064, and IPQ8064.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The TOP_INIT, ie bit 4-7 of the WDOG_TIMEOUT_RANGE_REG_OFFSET register
may be zero, so the timeout period may be very short after initialization
is done, thus the system may be reset soon after enabling. We fix this
problem by also initialising the TOP_INIT when setting TOP in function
dw_wdt_set_top().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add Cadence WDT driver. This is used by Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to store the return value of misc_deregister() in a
variable. Instead we can just return the value directly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Building booke_wdt fails when trying to build as a module as there is no
early_param() in module. Fix by using module_param() instead of early_param().
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
optimizations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJUPlLCAAoJENNvdpvBGATwpN8P/jnbDL1RqM9ZEAWfbDhvYumR
Fi59b3IDzSJHuuJeP0nTblVbbWclpO9ljCd18ttsHr8gBXA0ViaEU0XvWbpHIwPN
1fr1/Ovd0wvBdIVdLlaLXTR9skH4lbkiXxv/tkfjVCOSpzqiKID98Z72e/gUjB7Z
8xjAn/mTCnXKnhqMGzi8RC2MP1wgY//ErR21bj6so/8RC8zu4P6JuVj/hI6s0y5i
IPtAmjhdM7nxnS0wJwj7dLT0yNDftDh69qE6CgIwyK+Xn/SZFgYwE6+l02dj3DET
ZcAzTT9ToTMJdWtMu+5Y4LY8ObJ5xqMPbMoUclQ3DWe6nZicvtcBVCjfG/J8pFlY
IFD0nfh/OpX9cQMwJ+5Y8P4TrMiqM+FfuLfu+X83gLyrAyIazwoaZls2lxlEyC0w
M25oAqeKGUeVakVlmDZlVyBf05cu5m62x1rRvpcwMXMNhJl8/xwsSdhdYGeJfbO0
0MfL1n6GmvHvouMXKNsXlat/w3QVaQWVRzqdF9x7Q730fSHC/zxVGO+Po3jz2fBd
fBdfE14BIIU7nkyBVy0CZG5SDmQW4YACocOv/ATmII9j76F9eZQ3zsA8J1x+dLmJ
dP1Uxvsn1C3HW8Ua239j0XUJncglb06iEId0ywdkmWcc1rbzsyZ/NzXN/QBdZmqB
9g4GKAXAyh15PeBTJ5K/
=vWic
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"A large number of cleanups and bug fixes, with some (minor) journal
optimizations"
[ This got sent to me before -rc1, but was stuck in my spam folder. - Linus ]
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (67 commits)
ext4: check s_chksum_driver when looking for bg csum presence
ext4: move error report out of atomic context in ext4_init_block_bitmap()
ext4: Replace open coded mdata csum feature to helper function
ext4: delete useless comments about ext4_move_extents
ext4: fix reservation overflow in ext4_da_write_begin
ext4: add ext4_iget_normal() which is to be used for dir tree lookups
ext4: don't orphan or truncate the boot loader inode
ext4: grab missed write_count for EXT4_IOC_SWAP_BOOT
ext4: optimize block allocation on grow indepth
ext4: get rid of code duplication
ext4: fix over-defensive complaint after journal abort
ext4: fix return value of ext4_do_update_inode
ext4: fix mmap data corruption when blocksize < pagesize
vfs: fix data corruption when blocksize < pagesize for mmaped data
ext4: fold ext4_nojournal_sops into ext4_sops
ext4: support freezing ext2 (nojournal) file systems
ext4: fold ext4_sync_fs_nojournal() into ext4_sync_fs()
ext4: don't check quota format when there are no quota files
jbd2: simplify calling convention around __jbd2_journal_clean_checkpoint_list
jbd2: avoid pointless scanning of checkpoint lists
...
A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148,
and basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=V3Rv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148, and
basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late"
* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: corrected bcm2835 search
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
MAINTAINERS: Update Santosh Shilimkar's email id
ARM: sunxi_defconfig: enable CONFIG_REGULATOR
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
Merge "qcom DT changes for v3.18-3" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18-3
* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148
* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Arc+
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull more fixes from Kukjin Kim:
2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>
