Leave the common code in radeon_encoders.c and move the atom
specific code to atombios_encoders.c. This matches legacy
encoder setup and crtc setup.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DP MST is DP multi-stream support, part of DP 1.2.
v2: switch to a helper macro as suggested by Michel.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The existing function was getting too big and complex.
Break it down into a more manageable set of functions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Return the encoder id rather than a boolean. This is needed
for differentiate between multiple DP bridge chips.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Settings in this table reflect the physical panel/connector rather
than the internal dig encoding.
v2: fix typo for DRM_MODE_CONNECTOR_VGA case.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
llano has fully routeable dig encoders similar to DCE3.2 while
ontario has a hardcoded mapping similar to DCE4.0.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The encoders are supposedly fully routeable, but changing the mapping
doesn't always seem to take. Using a hardcoded mapping is much more
reliable.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41366
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
DVOOutputControl checks the value of of bios scratch reg 3
on some tables and assumes the encoder is already enabled
if the DFP2_ACTIVE bit is set. Clear that bit so the table
sets the DDIA enable bit properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to add support for 4 crtcs when setting the possible crtcs
for the encoders.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is used during phy init to set up the phy for DP. This may
fix DP problems on DCE3.2 cards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Certain revisions of the vbios on DCE3.2 cards have a bug
in the transmitter control table which prevents duallink from
being enabled properly on some cards. The action switch statement
jumps to the wrong offset for the OUTPUT_ENABLE action. The fix
is to use the ENABLE action rather than the OUTPUT_ENABLE action
on the affected cards. In fixed version of the vbios, both
actions jump to the same offset, so the change should be safe.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
DP clock and lanes were not set properly for DP bridges.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to set up the bridge for DDC prior to the
i2c over aux transaction.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should give us more reliable results if the table
is called before an active device is set.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The PHY was not initialized correctly after
ac89af1e10 since
the function bailed early as an encoder was not
assigned. The encoder isn't necessary for PHY init
so just assign to 0 for init so that the table
is executed.
Reported-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Tested-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It only needs to be called once at startup, not for every
modeset.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- reorganize the functions based on use
- clean up function naming
- rework link training to better match what we use internally
- add initial support for DP 1.2 (no MST yet)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fusion hardware often has DP to VGA/LVDS/TMDS bridges to
handle non-DP encoders. Internally we treat them mostly
like DP.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
eDP is usually used as an LVDS replacement, so treat
it more like LVDS from the user perspective.
v2: encoder mode is always DP for eDP.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In DP mode, the DP ref clock can come from PPLL, DCPLL, or ext clock,
depending on the asic. The crtc virtual pixel clock is derived from
the DP ref clock.
- DCE4: PPLL or ext clock
- DCE5: DCPLL or ext clock
Setting ATOM_PPLL_INVALID will cause SetPixelClock to skip
PPLL/DCPLL programming and only program the DP DTO for the
crtc virtual pixel clock.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- set scaler table clears the interleave bit, need to
reset it in encoder quirks, this was already done for
pre-dce4.
- remove the interleave settings from set_base() functions
this is now handled in the encoder quirks functions, and
isn't technically part of the display base setup.
- rename evergreen_do_set_base() to dce4_do_set_base() since
it's used on both evergreen and NI asics.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28182
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This error is reported by cppcheck:
drivers/gpu/drm/radeon/radeon_encoders.c:1066: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?
It looks like cppcheck is correct, so fix this. No test was run.
Cc: David Airlie <airlied@linux.ie>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Force DVI mode if the user specifies radeon.audio=0. The driver
doesn't handle HDMI mode properly in some cases.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=27731
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
This avoids some issues in the current hdmi audio code for monitors
without audio.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Needed to tell which DIG encoders are HBR2 capable for DP 1.2.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DVOOutputControl table was removed for DCE5.
DVOEncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DAC1OutputControl table was removed for DCE5.
DAC1EncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Works more like DCE4.0 despite what the docs say.
This fixes blank screen issues when changing crtc
routing due to incorrect crtc to dig mapping.
v2: only two DIGx blocks, routing is hardcoded
based on link.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These are external encoder chips connected via DVO or DP.
The actual external encoder programming is handled by the
kms encoder functions for primary encoder.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Handle all the various asic family specific things for DVO.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The eDP panel must be powered up for aux transactions, so power it
up for detect and mode probe functions, otherwise power it up or
down based on dpms.
v2:
- only mess with eDP panel on DCE4+
- only mess with eDP panel on eDP connectors, not all DP connectors
v3:
- be extra careful to only mess with eDP panels on eDP connectors
v4:
- avoid possible null derefernce if a connector has not been
assigned to the encoder
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If there was no connector mapped to the encoder, atombios_get_encoder_mode()
returned 0 which is the id for DP. Return something sane instead based on
the encoder id. This avoids hitting the DP paths on non-DP encoders.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a follow on to:
26b5bc9864
(drm/radeon/kms: add support for router objects)
That patch added support for systems that use a mux to control
the ddc line routing between the connectors. This patch adds
support for systems that use a mux to control the encoder
clock and data path routing to the connectors.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=31339
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The A/B links aren't independantly useable on these blocks so when
we disable the encoders, make sure to only disable the encoder when
there is no connector using it.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=18564
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
