This time there are a number of actual code fixes, plus
a small set of device tree issues getting addressed:
- Renesas:
- one defconfig cleanup to allow a later Kconfig change
- Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
- TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
- NXP i.MX
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
- Amlogic Meson
- misc DT fixes
- SoC ID fixes to detect all chips correctly
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Xlng
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC fixes from Arnd Bergmann:
"This time there are a number of actual code fixes, plus a small set of
device tree issues getting addressed:
Renesas:
- one defconfig cleanup to allow a later Kconfig change
Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target
module driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
NXP i.MX:
- A couple of fixes on i.MX platform device registration code to
stop the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
Amlogic Meson:
- misc DT fixes
- SoC ID fixes to detect all chips correctly"
* tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema
ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema
arm64: dts: stratix10: increase QSPI reg address in nand dts file
arm64: dts: stratix10: add status to qspi dts node
arm64: dts: agilex: add status to qspi dts node
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
-----BEGIN PGP SIGNATURE-----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=ekbH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8-rc cycle
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
* tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
Link: https://lore.kernel.org/r/pull-1594840100-132735@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8Nxv4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4fIAf/SKUzFbQ/INaU98yW8zONnZVzD/jI
3oTnBP87YJRNiyrLF1lWLs55vfnhum7yXJZXdMbwP55fdJKVaV4StePGz9Sh4Gba
4COHOF3XvF73b4kpcCQEr1U+Y0KHEfMbkwONmerk9ZkRThY2uqcRsdj4br+XA9eU
19ppWdOYZHMjegPu0KuxJlevZJDO6s9I4MCKFWmGgWhanLeGXXd2xtJEgqTWtTnS
EFjOFdBQF+5yd0VY/j6WHBDHWa/fXhDFoAO8Wc5LMCP3VybZdciIi4mN8y0UZoNG
Q5UnBvpYMCqrBwVlyqgeDtJUvYd+33dHqsRbU3KN8yBpRnyHupR9UvcFLA==
=+Gmy
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 2:
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
* tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
Link: https://lore.kernel.org/r/20200714145649.GP15718@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix dtschema validator warnings like:
l2-cache@fffff000: $nodename:0:
'l2-cache@fffff000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Fixes: 475dc86d08 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Got following d_can probe errors with kernel 5.8-rc1 on am437x
[ 10.730822] CAN device driver interface
Starting Wait for Network to be Configured...
[ OK ] Reached target Network.
[ 10.787363] c_can_platform 481cc000.can: probe failed
[ 10.792484] c_can_platform: probe of 481cc000.can failed with error -2
[ 10.799457] c_can_platform 481d0000.can: probe failed
[ 10.804617] c_can_platform: probe of 481d0000.can failed with error -2
actually, Tony has fixed this issue on am335x with the patch [3]
Since am437x has the same clock structure with am335x
[1][2], so reuse the code from Tony Lindgren's patch [3] to fix it.
[1]: https://www.ti.com/lit/pdf/spruh73 Chapter-23, Figure 23-1. DCAN
Integration
[2]: https://www.ti.com/lit/pdf/spruhl7 Chapter-25, Figure 25-1. DCAN
Integration
[3]: commit 516f1117d0 ("ARM: dts: Configure osc clock for d_can on
am335x")
Fixes: 1a5cd7c23c ("bus: ti-sysc: Enable all clocks directly during init to read revision")
Signed-off-by: dillon min <dillon.minfei@gmail.com>
[tony@atomide.com: aligned commit message a bit for readability]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull input fixes from Dmitry Torokhov:
"A few quirks for the Elan touchpad driver, another Thinkpad is being
switched over from PS/2 to native RMI4 interface, and we gave a brand
new SW_MACHINE_COVER switch definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add more hardware ID for Lenovo laptops
Input: i8042 - add Lenovo XiaoXin Air 12 to i8042 nomux list
Revert "Input: elants_i2c - report resolution information for touch major"
Input: elan_i2c - only increment wakeup count on touch
Input: synaptics - enable InterTouch for ThinkPad X1E 1st gen
ARM: dts: n900: remove mmc1 card detect gpio
Input: add `SW_MACHINE_COVER`
The audio codec on the GW551x routes to ssi1. It fixes audio capture on
the device.
Cc: stable@vger.kernel.org
Fixes: 3117e851ce ("ARM: dts: imx: Add TDA19971 HDMI Receiver to GW551x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead, expose the key via the input framework, as SW_MACHINE_COVER
The chip-detect GPIO is actually detecting if the cover is closed.
Technically it's possible to use the SD card with open cover. The
only downside is risk of battery falling out and user being able
to physically remove the card.
The behaviour of SD card not being available when the device is
open is unexpected and creates more problems than it solves. There
is a high chance, that more people accidentally break their rootfs
by opening the case without physically removing the card.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Link: https://lore.kernel.org/r/20200612125402.18393-3-merlijn@wizzup.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix dtschema validator warnings like:
l2-cache-controller@c4200000: $nodename:0:
'l2-cache-controller@c4200000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200626080626.4080-1-krzk@kernel.org
The OMAP developers are particularly active at hunting down regressions,
so this is a separate branch with OMAP specific fixes for the v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks like
I only tested suspend and resume before dropping the legacy platform
data, and forgot to test it after dropping it. Turns out the main issue
was that we no longer have platform code calling pm_runtime_suspend
for DSS like we did for the legacy platform data case, and that fix
is still being discussed on the dri-devel list and will get merged
separately. The DSS related testing exposed a pile other other display
related issues that also need fixing though":
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=FFTv
-----END PGP SIGNATURE-----
Merge tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM OMAP fixes from Arnd Bergmann:
"The OMAP developers are particularly active at hunting down
regressions, so this is a separate branch with OMAP specific
fixes for v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks
like I only tested suspend and resume before dropping the legacy
platform data, and forgot to test it after dropping it. Turns out
the main issue was that we no longer have platform code calling
pm_runtime_suspend for DSS like we did for the legacy platform data
case, and that fix is still being discussed on the dri-devel list
and will get merged separately. The DSS related testing exposed a
pile other other display related issues that also need fixing
though":
- Fix ti-sysc optional clock handling and reset status checks for
devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested to
avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process"
* tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
...
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7zM08UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5HNAf+Kw6EPNxYom/MJ4P92gxLAtPA6AO4
+WuLYmSphhgmGAQLFU4UiTH/2sYXmT7fSDwLhfZI5XJp6j8J89Hxe2kyMomvIT92
Xbbzp7fr+2FPGgyI6ImiKTFeSZiT0LPq5fs1uF2lTP6+/SklF9yy5ynUvNULrD4b
iSAXOZkMz6Ft8dn1zYrTKPIYfsTe1zXsDgw8a9sc+0LfgiR5cBTq359jHrN5Q0Tq
NYoOHT+8V5C8BVmzp5I1zoghZEayPT2Ui1JIwBiyVij8KqZvYY3wckjPqgdfQ1vK
IzGksPWRojKAw2RKA59kpUR/pgoZH3GYnfjmCAIOkMnMSgAqz1inZZq2oA==
=iERQ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8:
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
* tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx8m: fix build warning
ARM: imx6: add missing put_device() call in imx6q_suspend_init()
ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram()
soc: imx8m: Correct i.MX8MP UID fuse offset
ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain
ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM
arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2
arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range
arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range
Link: https://lore.kernel.org/r/20200624111725.GA24312@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
5.8, please pull the following:
- Rafal adds a missing 'device_type' property to the Luxul XWC-2000
required for the memory nodes to be correctly parsed by Linux
- Matthew provides two fixes for the NSP SoCs, one to disable the PL330
DMA controller by default since it can be left in reset by the
bootloader and the second to correct the flow accelerator mailbox node
-----BEGIN PGP SIGNATURE-----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=SUaO
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.8/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.8, please pull the following:
- Rafal adds a missing 'device_type' property to the Luxul XWC-2000
required for the memory nodes to be correctly parsed by Linux
- Matthew provides two fixes for the NSP SoCs, one to disable the PL330
DMA controller by default since it can be left in reset by the
bootloader and the second to correct the flow accelerator mailbox node
* tag 'arm-soc/for-5.8/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Correct FA2 mailbox node
ARM: dts: NSP: Disable PL330 by default, add dma-coherent property
ARM: dts: BCM5301X: Add missing memory "device_type" for Luxul XWC-2000
Link: https://lore.kernel.org/r/20200619202250.19029-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few fixes for various devices:
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
-----BEGIN PGP SIGNATURE-----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=Hqfw
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Few dts fixes for omaps for v5.8
Few fixes for various devices:
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
* tag 'omap-for-v5.8/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Link: https://lore.kernel.org/r/pull-1592499282-121092@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
-----BEGIN PGP SIGNATURE-----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=UNki
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Missed sdhci patch for am3 and am4
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
* tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Move am33xx and am43xx mmc nodes to sdhci-omap driver
Link: https://lore.kernel.org/r/pull-1591637467-607254@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
-----BEGIN PGP SIGNATURE-----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=fT9A
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Partial revert of some recent fixes to silence DTC warning which broke
clocks on some Vexpress platforms resulting in boot issues.
-----BEGIN PGP SIGNATURE-----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=2f3w
-----END PGP SIGNATURE-----
Merge tag 'juno-fix-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARMv8 Juno/Vexpress/Fast Models fix for v5.8
Partial revert of some recent fixes to silence DTC warning which broke
clocks on some Vexpress platforms resulting in boot issues.
* tag 'juno-fix-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress: Move mcc node back into motherboard node
Link: https://lore.kernel.org/r/20200609180447.GB5732@bogus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The WDOG_ANY signal is connected to the RESET_IN signal of the SoM
and baseboard. It is currently configured as push-pull, which means
that if some external device like a programmer wants to assert the
RESET_IN signal by pulling it to ground, it drives against the high
level WDOG_ANY output of the SoC.
To fix this we set the WDOG_ANY signal to open-drain configuration.
That way we make sure that the RESET_IN can be asserted by the
watchdog as well as by external devices.
Fixes: 1ea4b76cdf ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog's WDOG_ANY signal is used to trigger a POR of the SoC,
if a soft reset is issued. As the SoM hardware connects the WDOG_ANY
and the POR signals, the watchdog node itself and the pin
configuration should be part of the common SoM devicetree.
Let's move it from the baseboard's devicetree to its proper place.
Fixes: 1ea4b76cdf ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The FA2 mailbox is specified at 0x18025000 but should actually be
0x18025c00, length 0x400 according to socregs_nsp.h and board_bu.c. Also
the interrupt was off by one and should be GIC SPI 151 instead of 150.
Fixes: 17d5171723 ("ARM: dts: NSP: Add mailbox (PDC) to NSP")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Since commit cd28d1d6e5 ("net: phy: at803x: Disable phy delay for
RGMII mode") the networking is broken on the BeagleBone AI which has
the AR8035 PHY for Gigabit Ethernet [0]. The fix is to switch from
phy-mode = "rgmii" to phy-mode = "rgmii-rxid".
Note: Grygorii made a similar DT fix for other AM57xx boards with a
different phy in commit 820f8a870f ("ARM: dts: am57xx: fix networking
on boards with ksz9031 phy").
[0] https://git.io/Jf7PX
Fixes: 520557d485 ("ARM: dts: am5729: beaglebone-ai: adding device tree")
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I accidentally flipped the system timer to use system clock instead of
the 32k source clock.
Fixes: 14b1925a72 ("ARM: dts: Configure system timers for omap4")
Signed-off-by: Tony Lindgren <tony@atomide.com>
While testing the recent suspend and resume regressions I noticed that
duovero can still end up losing edge gpio interrupts on runtime
suspend. This causes NFSroot easily stopping working after resume on
duovero.
Let's fix the issue by using gpio level interrupts for smsc as then
the gpio interrupt state is seen by the gpio controller on resume.
Fixes: 731b409878 ("ARM: dts: Configure duovero for to allow core retention during idle")
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3358 pin mcasp0_aclkr (ZCZ ball B13) [0] is routed to P1.31 header [1]
Mode 4 of this pin is mmc0_sdwp (SD Write Protect). A signal connected
to P1.31 may accidentally trigger mmc0 write protection. To avoid this
situation, do not put mcasp0_aclkr in mode 4 (mmc0_sdwp) by default.
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#531_Expansion_Headers
Fixes: 047905376a (ARM: dts: Add am335x-pocketbeagle)
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the PL330 is enabled by default. However if left in IDM reset, as is
the case with the Meraki and Synology NSP devices, the system will hang when
probing for the PL330's AMBA peripheral ID. We therefore should be able to
disable it in these cases.
The PL330 is also included among of the list of peripherals put into coherent
mode, so "dma-coherent" has been added here as well.
Fixes: 5fa1026a3e ("ARM: dts: NSP: Add PL330 support")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
-----BEGIN PGP SIGNATURE-----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=1NIT
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
EFI on ARM only supports short descriptors, and given that it mandates
that the MMU and caches are on, it is implied that booting in HYP mode
is not supported.
However, implementations of EFI exist (i.e., U-Boot) that ignore this
requirement, which is not entirely unreasonable, given that it makes
HYP mode inaccessible to the operating system.
So let's make sure that we can deal with this condition gracefully.
We already tolerate booting the EFI stub with the caches off (even
though this violates the EFI spec as well), and so we should deal
with HYP mode boot with MMU and caches either on or off.
- When the MMU and caches are on, we can ignore the HYP stub altogether,
since we can carry on executing at HYP. We do need to ensure that we
disable the MMU at HYP before entering the kernel proper.
- When the MMU and caches are off, we have to drop to SVC mode so that
we can set up the page tables using short descriptors. In this case,
we need to install the HYP stub as usual, so that we can return to HYP
mode before handing over to the kernel proper.
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Redefine GZIP, BZIP2, LZOP variables as KGZIP, KBZIP2, KLZOP resp.
GZIP, BZIP2, LZOP env variables are reserved by the tools. The original
attempt to redefine them internally doesn't work in makefiles/scripts
intercall scenarios, e.g., "make GZIP=gzip bindeb-pkg" and results in
broken builds. There can be other broken build commands because of this,
so the universal solution is to use non-reserved env variables for the
compression tools.
Fixes: 8dfb61dcba ("kbuild: add variables for compression tools")
Signed-off-by: Denis Efremov <efremov@linux.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox nodes defined in various dts files have been moved to
common dra7-ipu-dsp-common.dtsi and dra74-ipu-dsp-common.dtsi files
in commit a11a2f73b3 ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes
into common files"), but the nodes were erroneously left out in the
dra7-evm-common.dtsi file. Fix this by removing these duplicate nodes.
Fixes: a11a2f73b3 ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 5390130f3b ("ARM: dts: dra7: add timer_sys_ck entries
for IPU/DSP timers") was added to allow the OMAP clocksource timer
driver to use the clock aliases when reconfiguring the parent clock
source for the timer functional clocks after the timer_sys_ck clock
aliases got cleaned up in commit a8202cd517 ("clk: ti: dra7: drop
unnecessary clock aliases").
The above patch however has missed adding the entries for couple of
timers (14, 15 and 16), and also added erroneously in the parent
ti-sysc nodes for couple of clocks (timers 4, 5 and 6). Fix these
properly, so that any of these timers can be used with OMAP remoteproc
IPU and DSP devices. The always-on timers 1 and 12 are not expected
to use this clock source, so they are not modified.
Fixes: 5390130f3b ("ARM: dts: dra7: add timer_sys_ck entries for IPU/DSP timers")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x TRM: Figure 16-23 define sysconfig register and soft_reset
are in first position corresponding to SYSC_OMAP4_SOFTRESET defined
in ti-sysc.h.
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x TRM: Table 2-1 defines USBSS - USB Queue Manager in memory region
0x4740 0000 to 0x4740 7FFF.
Looks like the older TRM revisions list the range from 0x5000 to 0x8000
as reserved.
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzqVA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynftwCfeanyI6TR5AdfJVZN50B6/ySvVwcAn07i9VRX
tnt2kz0UqReYpLt0wyJ7
=YP7o
-----END PGP SIGNATURE-----
Merge tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
- fix warnings in 'make clean' for ARCH=um, hexagon, h8300, unicore32
- ensure to rebuild all objects when the compiler is upgraded
- exclude system headers from dependency tracking and fixdep processing
- fix potential bit-size mismatch between the kernel and BPF user-mode
helper
- add the new syntax 'userprogs' to build user-space programs for the
target architecture (the same arch as the kernel)
- compile user-space sample code under samples/ for the target arch
instead of the host arch
- make headers_install fail if a CONFIG option is leaked to user-space
- sanitize the output format of scripts/checkstack.pl
- handle ARM 'push' instruction in scripts/checkstack.pl
- error out before modpost if a module name conflict is found
- error out when multiple directories are passed to M= because this
feature is broken for a long time
- add CONFIG_DEBUG_INFO_COMPRESSED to support compressed debug info
- a lot of cleanups of modpost
- dump vmlinux symbols out into vmlinux.symvers, and reuse it in the
second pass of modpost
- do not run the second pass of modpost if nothing in modules is updated
- install modules.builtin(.modinfo) by 'make install' as well as by
'make modules_install' because it is useful even when CONFIG_MODULES=n
- add new command line variables, GZIP, BZIP2, LZOP, LZMA, LZ4, and XZ
to allow users to use alternatives such as pigz, pbzip2, etc.
-----BEGIN PGP SIGNATURE-----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=GKe5
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- fix warnings in 'make clean' for ARCH=um, hexagon, h8300, unicore32
- ensure to rebuild all objects when the compiler is upgraded
- exclude system headers from dependency tracking and fixdep processing
- fix potential bit-size mismatch between the kernel and BPF user-mode
helper
- add the new syntax 'userprogs' to build user-space programs for the
target architecture (the same arch as the kernel)
- compile user-space sample code under samples/ for the target arch
instead of the host arch
- make headers_install fail if a CONFIG option is leaked to user-space
- sanitize the output format of scripts/checkstack.pl
- handle ARM 'push' instruction in scripts/checkstack.pl
- error out before modpost if a module name conflict is found
- error out when multiple directories are passed to M= because this
feature is broken for a long time
- add CONFIG_DEBUG_INFO_COMPRESSED to support compressed debug info
- a lot of cleanups of modpost
- dump vmlinux symbols out into vmlinux.symvers, and reuse it in the
second pass of modpost
- do not run the second pass of modpost if nothing in modules is
updated
- install modules.builtin(.modinfo) by 'make install' as well as by
'make modules_install' because it is useful even when
CONFIG_MODULES=n
- add new command line variables, GZIP, BZIP2, LZOP, LZMA, LZ4, and XZ
to allow users to use alternatives such as pigz, pbzip2, etc.
* tag 'kbuild-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (96 commits)
kbuild: add variables for compression tools
Makefile: install modules.builtin even if CONFIG_MODULES=n
mksysmap: Fix the mismatch of '.L' symbols in System.map
kbuild: doc: rename LDFLAGS to KBUILD_LDFLAGS
modpost: change elf_info->size to size_t
modpost: remove is_vmlinux() helper
modpost: strip .o from modname before calling new_module()
modpost: set have_vmlinux in new_module()
modpost: remove mod->skip struct member
modpost: add mod->is_vmlinux struct member
modpost: remove is_vmlinux() call in check_for_{gpl_usage,unused}()
modpost: remove mod->is_dot_o struct member
modpost: move -d option in scripts/Makefile.modpost
modpost: remove -s option
modpost: remove get_next_text() and make {grab,release_}file static
modpost: use read_text_file() and get_line() for reading text files
modpost: avoid false-positive file open error
modpost: fix potential mmap'ed file overrun in get_src_version()
modpost: add read_text_file() and get_line() helpers
modpost: do not call get_modinfo() for vmlinux(.o)
...
Allow user to use alternative implementations of compression tools,
such as pigz, pbzip2, pxz. For example, multi-threaded tools to
speed up the build:
$ make GZIP=pigz BZIP2=pbzip2
Variables _GZIP, _BZIP2, _LZOP are used internally because original env
vars are reserved by the tools. The use of GZIP in gzip tool is obsolete
since 2015. However, alternative implementations (e.g., pigz) still rely
on it. BZIP2, BZIP, LZOP vars are not obsolescent.
The credit goes to @grsecurity.
As a sidenote, for multi-threaded lzma, xz compression one can use:
$ export XZ_OPT="--threads=0"
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This is the set of device tree changes, mostly covering new
hardware support, with 577 patches touching a little over 500
files.
There are five new Arm SoCs supported in this release, all of
them for existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in
both NAS devices and Android Set-top-box designs, along
with the "Horseradish", "Lion Skin" and "Mjolnir" reference
platforms; the Mele X1000 and Xnano X5 set-top-boxes and
the Banana Pi BPi-M4 single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC
and the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the
Odroid-GO Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2"
and YADRO OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform"
reference board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board
computer and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in existing
SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=17kt
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
Commit d9258898ad ("arm64: dts: arm: vexpress: Move fixed devices
out of bus node") moved the "mcc" DT node into the root node, because
it does not have any children using "reg" properties, so does violate
some dtc checks about "simple-bus" nodes.
However this broke the vexpress config-bus code, which walks up the
device tree to find the first node with an "arm,vexpress,site" property.
This gave the wrong result (matching the root node instead of the
motherboard node), so broke the clocks and some other devices for
VExpress boards.
Move the whole node back into its original position. This re-introduces
the dtc warning, but is conceptually the right thing to do. The dtc
warning seems to be overzealous here, there are discussions on fixing or
relaxing this check instead.
Link: https://lore.kernel.org/r/20200603162237.16319-1-andre.przywara@arm.com
Fixes: d9258898ad ("arm64: dts: vexpress: Move fixed devices out of bus node")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place
-----BEGIN PGP SIGNATURE-----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=FFm0
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The truly boring timer and clocksource updates for 5.8:
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place"
* tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
dt-bindings: timer: Add renesas,em-sti bindings
clocksource/drivers/timer-versatile: Clear OF_POPULATED flag
clocksource: mips-gic-timer: Mark GIC timer as unstable if ref clock changes
clocksource: mips-gic-timer: Register as sched_clock
clocksource: dw_apb_timer_of: Fix missing clockevent timers
clocksource: dw_apb_timer: Affiliate of-based timer with any CPU
clocksource: dw_apb_timer: Make CPU-affiliation being optional
dt-bindings: timer: Move snps,dw-apb-timer DT schema from rtc
dt-bindings: rtc: Convert snps,dw-apb-timer to DT schema
clocksource/drivers/timer-ti-dm: Do one override clock parent in prepare()
clocksource/drivers/timer-ti-dm: Fix spelling mistake "detectt" -> "detect"
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
drivers/clocksource/arm_arch_timer: Remove duplicate error message
clocksource/drivers/arc_timer: Remove duplicate error message
clocksource/drivers/rda: drop redundant Kconfig dependency
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
...
