When suspending, Bluetooth disconnects all connected peers devices. If
an LE connection is started but isn't completed, we will see an LE
Create Connection Cancel instead of an HCI disconnect. This just adds
a check to see if an LE cancel was the last disconnected device and wake
the suspend thread when that is the case.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
el/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2021-02-11
Here's the main bluetooth-next pull request for 5.12:
- Add support for advertising monitor offliading using Microsoft
vendor extensions
- Add firmware download support for MediaTek MT7921U USB devices
- Suspend-related fixes for Qualcomm devices
- Add support for Intel GarfieldPeak controller
- Various other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a peer device doesn't support eSCO 2M we should skip the params that
use it when setting up sync connection since they will always fail.
Signed-off-by: Yu Liu <yudiliu@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Reported-by: Abaci Robot<abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some devices, e.g. the RTL8723BS bluetooth part, some USB attached devices,
completely drop from the bus on a system-suspend. These devices will
have their driver unbound and rebound on resume (when the dropping of
the bus gets detected) and will show up as a new HCI after resume.
These devices do not benefit from the suspend / resume handling work done
by the hci_suspend_notifier. At best this unnecessarily adds some time to
the suspend/resume time. But this may also actually cause problems, if the
code doing the driver unbinding runs after the pm-notifier then the
hci_suspend_notifier code will try to talk to a device which is now in
an uninitialized state.
This commit adds a new HCI_QUIRK_NO_SUSPEND_NOTIFIER quirk which allows
drivers to opt-out of the hci_suspend_notifier when they know beforehand
that their device will be fully re-initialized / reprobed on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These Kconfig files are included from net/Kconfig, inside the
if NET ... endif.
Remove 'depends on NET', which we know it is already met.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210125232026.106855-1-masahiroy@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bluetooth Core Specification v5.2, Vol. 3, Part A, section 1.4, table
1.1:
'Start Fragments always either begin with the first octet of the Basic
L2CAP header of a PDU or they have a length of zero (see [Vol 2] Part
B, Section 6.6.2).'
Apparently this was changed by the following errata:
https://www.bluetooth.org/tse/errata_view.cfm?errata_id=10216
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jump to the label done to decrement the reference count of HCI device
hdev on path that the Inquiry procedure is interrupted.
Fixes: 3e13fa1e1f ("Bluetooth: Fix hci_inquiry ioctl usage")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds logic to disable and reenable advertisement filters during
suspend and resume. After this patch, we would only receive packets from
devices in allow list during suspend.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When MSFT extension is supported, we don't have to interleave the scan
as we could just do allowlist scan.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implements the feature to disable/enable the filter used for
advertising monitor on MSFT controller, effectively have the same
effect as "remove all monitors" and "add all previously removed
monitors".
This feature would be needed when suspending, where we would not want
to get packets from anything outside the allowlist. Note that the
integration with the suspending part is not included in this patch.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the controller is powered off, the registered advertising monitor
is removed from the controller. This patch handles the re-registration
of those monitors when the power is on.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enables advertising monitor offloading to the controller, if MSFT
extension is supported. The kernel won't adjust the monitor parameters
to match what the controller supports - that is the user space's
responsibility.
This patch only manages the addition of monitors. Monitor removal is
going to be handled by another patch.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MSFT needs rssi parameter for monitoring advertisement packet,
therefore we should supply them from mgmt. This adds a new opcode
to add advertisement monitor with rssi parameters.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
u128_xor() takes pointers to quantities that are assumed to be at least
64-bit aligned, which is not guaranteed to be the case in the smp_c1()
routine. So switch to crypto_xor() instead.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Looks like this was missed when patching the source to clear the structures
throughout, causing this one instance to clear the struct after the response
id is assigned.
Fixes: eddb773211 ("Bluetooth: A2MP: Fix not initializing all members")
Signed-off-by: Christopher William Snowhill <chris@kode54.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Just like MGMT_OP_START_DISCOVERY, we should reject
MGMT_OP_START_SERVICE_DISCOVERY with MGMT_STATUS_BUSY when we are paused
for suspend.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a missing SUSPEND_SCAN_ENABLE in passive scan, remove the separate
function for configuring le scan during suspend and update the request
complete function to clear both enable and disable tasks.
Fixes: dce0a4be80 ("Bluetooth: Set missing suspend task bits")
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added new commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When suspending, mark SUSPEND_SCAN_ENABLE and SUSPEND_SCAN_DISABLE tasks
correctly when either classic or le scanning is modified.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For advertising, we wish to know the LE tx power capabilities of the
controller in userspace, so this patch edits the Security Info MGMT
command to be more generic, such that other various controller
capabilities can be included in the EIR data. This change also includes
the LE min and max tx power into this newly-named command.
The change was tested by manually verifying that the MGMT command
returns the tx power range as expected in userspace.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Queries tx power via HCI_LE_Read_Transmit_Power command when the hci
device is initialized, and stores resulting min/max LE power in hdev
struct. If command isn't available (< BT5 support), min/max values
both default to HCI_TX_POWER_INVALID.
This patch is manually verified by ensuring BT5 devices correctly query
and receive controller tx power range.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch takes the min/max intervals and tx power optionally provided
in mgmt interface, stores them in the advertisement struct, and uses
them when configuring the hci requests. While tx power is not used if
extended advertising is unavailable, software rotation will use the min
and max advertising intervals specified by the client.
This change is validated manually by ensuring the min/max intervals are
propagated to the controller on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks, and that tx power is
propagated correctly on hatch. These tests are performed with multiple
advertisements simultaneously.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds support for the new advertising add interface, with the
first command setting advertising parameters and the second to set
advertising data. The set parameters command allows the caller to leave
some fields "unset", with a params bitfield defining which params were
purposefully set. Unset parameters will be given defaults when calling
hci_add_adv_instance. The data passed to the param mgmt command is
allowed to be flexible, so in the future if bluetoothd passes a larger
structure with new params, the mgmt command will ignore the unknown
members at the end.
This change has been validated on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks running bluetoothd that
support this new interface. I ran the following manual tests:
- Set several (3) advertisements using modified test_advertisement.py
- For each, validate correct data and parameters in btmon trace
- Verified both for software rotation and extended adv
Automatic test suite also run, testing many (25) scenarios of single and
multi-advertising for data/parameter correctness.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We wish to handle advertising data separately from advertising
parameters in our new MGMT requests. This change adds a helper that
allows the advertising data and scan response to be updated for an
existing advertising instance.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch add a configurable parameter to switch off the interleave
scan feature.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Refactor read default system configuration function so that it's capable
of returning different types than u16
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds code to handle the active scan during interleave
scan. The interleave scan will be canceled when users start active scan,
and it will be restarted after active scan stopped.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds code to handle the system suspension during interleave
scan. The interleave scan will be canceled when the system is going to
sleep, and will be restarted after waking up.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements the interleaving between allowlist scan and
no-filter scan. It'll be used to save power when at least one monitor is
registered and at least one pending connection or one device to be
scanned for.
The durations of the allowlist scan and the no-filter scan are
controlled by MGMT command: Set Default System Configuration. The
default values are set randomly for now.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
During controller initialization, an LE Set RPA Timeout command is sent
to the controller if supported. However, the value checked to determine
if the command is supported is incorrect. Page 1921 of the Bluetooth
Core Spec v5.2 shows that bit 2 of octet 35 of the Supported_Commands
field corresponds to the LE Set RPA Timeout command, but currently
bit 6 of octet 35 is checked. This patch checks the correct value
instead.
This issue led to the error seen in the following btmon output during
initialization of an adapter (rtl8761b) and prevented initialization
from completing.
< HCI Command: LE Set Resolvable Private Address Timeout (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Complete (0x0e) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 2
Status: Unsupported Remote Feature / Unsupported LMP Feature (0x1a)
= Close Index: 00:E0:4C:6B:E5:03
The error did not appear when running with this patch.
Signed-off-by: Edward Vear <edwardvear@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This renames get_adv_instance_scan_rsp to adv_instance_is_scannable and
make it return a bool since it was not actually properly return the size
of the scan response as one could expect.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Current code is actually failing on the following tests of mgmt-tester
because get_adv_instance_scan_rsp_len did not account for flags that
cause scan response data to be included resulting in non-scannable
instance when in fact it should be scannable.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This test case is meant to verify that multiple
unknown options is included in the response.
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part A
page 1057
'On an unknown option failure (Result=0x0003),
the option(s) that contain anoption type field that is not
understood by the recipient of the L2CAP_CONFIGURATION_REQ
packet shall be included in the L2CAP_CONFIGURATION_RSP
packet unless they are hints.'
Before this patch:
> ACL Data RX: Handle 11 flags 0x02 dlen 24
L2CAP: Configure Request (0x04) ident 18 len 16
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [mandatory]
10 00 11 02 11 00 12 02 12 00
< ACL Data TX: Handle 11 flags 0x00 dlen 17
L2CAP: Configure Response (0x05) ident 18 len 9
Source CID: 64
Flags: 0x0000
Result: Failure - unknown options (0x0003)
Option: Unknown (0x10) [mandatory]
12
After this patch:
> ACL Data RX: Handle 11 flags 0x02 dlen 24
L2CAP: Configure Request (0x04) ident 5 len 16
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [mandatory]
10 00 11 02 11 00 12 02 12 00
< ACL Data TX: Handle 11 flags 0x00 dlen 23
L2CAP: Configure Response (0x05) ident 5 len 15
Source CID: 64
Flags: 0x0000
Result: Failure - unknown options (0x0003)
Option: Unknown (0x10) [mandatory]
10 11 01 11 12 01 12
Signed-off-by: Jimmy Wahlberg <jimmywa@spotify.com>
Reviewed-by: Luiz Augusto Von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This replaces the BT_DBG function to bt_dev_dbg as it is cleaner to show
the controller index in the debug message.
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the spec Ver 5.2, Vol 3, Part C, Sec 5.2.2.8:
Device in security mode 4 level 4 shall enforce:
128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms (E0 not allowed, SAFER+ not allowed,
and P-192 not allowed; encryption key not shortened)
This patch rejects connection with key size below 16 for FIPS
level services.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and
dead000000000200 is LIST_POISON2.
list_add corruption. next->prev should be prev (ffffffc1b0a33a08), \
but was dead000000000200. (next=ffffffc03ac77de0).
------------[ cut here ]------------
CPU: 3 PID: 2138 Comm: bluetoothd Tainted: G O 4.4.238+ #9
...
---[ end trace 0adc2158f0646eac ]---
Call trace:
[<ffffffc000443f78>] __list_add+0x38/0xb0
[<ffffffc0000f0d04>] add_wait_queue+0x4c/0x68
[<ffffffc00020eecc>] __pollwait+0xec/0x100
[<ffffffc000d1556c>] bt_sock_poll+0x74/0x200
[<ffffffc000bdb8a8>] sock_poll+0x110/0x128
[<ffffffc000210378>] do_sys_poll+0x220/0x480
[<ffffffc0002106f0>] SyS_poll+0x80/0x138
[<ffffffc00008510c>] __sys_trace_return+0x0/0x4
Unable to handle kernel paging request at virtual address dead000000000100
...
CPU: 4 PID: 5387 Comm: kworker/u15:3 Tainted: G W O 4.4.238+ #9
...
Call trace:
[<ffffffc0000f079c>] __wake_up_common+0x7c/0xa8
[<ffffffc0000f0818>] __wake_up+0x50/0x70
[<ffffffc000be11b0>] sock_def_wakeup+0x58/0x60
[<ffffffc000de5e10>] l2cap_sock_teardown_cb+0x200/0x224
[<ffffffc000d3f2ac>] l2cap_chan_del+0xa4/0x298
[<ffffffc000d45ea0>] l2cap_conn_del+0x118/0x198
[<ffffffc000d45f8c>] l2cap_disconn_cfm+0x6c/0x78
[<ffffffc000d29934>] hci_event_packet+0x564/0x2e30
[<ffffffc000d19b0c>] hci_rx_work+0x10c/0x360
[<ffffffc0000c2218>] process_one_work+0x268/0x460
[<ffffffc0000c2678>] worker_thread+0x268/0x480
[<ffffffc0000c94e0>] kthread+0x118/0x128
[<ffffffc000085070>] ret_from_fork+0x10/0x20
---[ end trace 0adc2158f0646ead ]---
Signed-off-by: Ole Bjørn Midtbø <omidtbo@cisco.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Avoid multiple attempts to create the debugfs entry, force_bredr_smp,
by moving it from the SMP registration to the BR/EDR controller init
section. hci_debugfs_create_bredr is only called when HCI_SETUP and
HCI_CONFIG is not set.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding device to white list the device is added to resolving list
also. It has to be added only when HCI_ENABLE_LL_PRIVACY flag is set.
HCI_ENABLE_LL_PRIVACY flag has to be tested before adding/deleting devices
to resolving list. use_ll_privacy macro is used only to check if controller
supports LL_Privacy.
https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 0eee35bdfa ("Bluetooth: Update resolving list when updating whitelist")
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an LE connection request is made, advertising is disabled and never
resumed. When a client has an active advertisement, this is disruptive.
This change adds resume logic for client-configured (non-directed)
advertisements after the connection attempt.
The patch was tested by registering an advertisement, initiating an LE
connection from a remote peer, and verifying that the advertisement is
re-activated after the connection is established. This is performed on
Hatch and Kukui Chromebooks.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
Fixes: d5e911928b ("Bluetooth: AMP: Process Physical Link Complete evt")
Reported-and-tested-by: syzbot+0bef568258653cff272f@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=0bef568258653cff272f
Signed-off-by: Anmol Karn <anmol.karan123@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-09-29
Here's the main bluetooth-next pull request for 5.10:
- Multiple fixes to suspend/resume handling
- Added mgmt events for controller suspend/resume state
- Improved extended advertising support
- btintel: Enhanced support for next generation controllers
- Added Qualcomm Bluetooth SoC WCN6855 support
- Several other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This checks if BT_HS is enabled relecting it on MGMT_SETTING_HS instead
of always reporting it as supported.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth High Speed requires hardware support which is very uncommon
nowadays since HS has not pickup interest by the industry.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes various places where a stack variable is used uninitialized.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During system powercycle when trying to get the random address
hci_get_random_address set own_addr_type as 0x01. In which if we enable
ll_privacy it is supposed to be 0x03.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the code auto-creates hci_conn only if the remote address has
been discovered before. This may not be the case. For example, the
remote device may trigger connection after reboot at already-paired
state so there is no inquiry result found, but it is still correct to
create the hci_conn when Connection Complete event is received.
A better guard is to check against bredr allowlist. Devices in the
allowlist have been given permission to auto-connect.
Fixes: 4f40afc6c7 ("Bluetooth: Handle BR/EDR devices during suspend")
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set scan parameters when there is at least one Advertisement monitor.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the count of Adv monitor upon monitor removal.
The following test was performed.
- Start two btmgmt consoles, issue a btmgmt advmon-remove command on one
console and observe a MGMT_EV_ADV_MONITOR_REMOVED event on the other.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Drop repeated words in net/bluetooth/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the controller will continue advertising when the system
enters suspend. This patch makes sure that all advertising instances are
paused when entering suspend, and resumed when suspend exits.
The Advertising and Suspend/Resume test suites were both run on this
change on 4.19 kernel with both hardware offloaded multi-advertising and
software rotated multi-advertising. In addition, a new test was added
that performs the following steps:
* Register 3 advertisements via bluez RegisterAdvertisement
* Verify reception of all advertisements by remote peer
* Enter suspend on DUT
* Verify failure to receive all advertisements by remote peer
* Exit suspend on DUT
* Verify reception of all advertisements by remote peer
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Emit controller suspend and resume events when we are ready for suspend
and we've resumed from suspend.
The controller suspend event will report whatever suspend state was
successfully entered. The controller resume event will check the first
HCI event that was received after we finished preparing for suspend and,
if it was a connection event, store the address of the peer that caused
the event. If it was not a connection event, we mark the wake reason as
an unexpected event.
Here is a sample btmon trace with these events:
@ MGMT Event: Controller Suspended (0x002d) plen 1
Suspend state: Page scanning and/or passive scanning (2)
@ MGMT Event: Controller Resumed (0x002e) plen 8
Wake reason: Remote wake due to peer device connection (2)
LE Address: CD:F3:CD:13:C5:9A (OUI CD-F3-CD)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the controller suspend and resume events, which will signal when
Bluetooth has completed preparing for suspend and when it's ready for
resume.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only set extended scan response only when it exists. Otherwise, clear
the scan response data.
Per the core spec v5.2, Vol 4, Part E, 7.8.55
If the advertising set is non-scannable and the Host uses this command
other than to discard existing data, the Controller shall return the
error code Invalid HCI Command Parameters (0x12).
On WCN3991, the controller correctly responds with Invalid Parameters
when this is sent. That error causes __hci_req_hci_power_on to fail
with -EINVAL and LE devices can't connect because background scanning
isn't configured.
Here is an hci trace of where this issue occurs during power on:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
Handle: 0x00
Properties: 0x0010
Use legacy advertising PDUs: ADV_NONCONN_IND
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect...
TX power: 127 dbm (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 1M (0x01)
SID: 0x00
Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
Status: Success (0x00)
TX power (selected): 9 dbm (0x09)
< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
Advertising handle: 0x00
Advertising random address: 08:FD:55:ED:22:28 (OUI 08-FD-55)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Set Random Address (0x08|0x0035) ncmd
Status: Success (0x00)
< HCI Command: LE Set Extended Scan Response Data (0x08|0x0038) plen 35
Handle: 0x00
Operation: Complete scan response data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x0d
Name (short): Chromebook
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Response Data (0x08|0x0038) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For new advertising features, it will be important for userspace to
know the capabilities of the controller and kernel. If the controller
and kernel support extended advertising, we include flags indicating
hardware offloading support and support for setting tx power of adv
instances.
In the future, vendor-specific commands may allow the setting of tx
power in advertising instances, but for now this feature is only
marked available if extended advertising is supported.
This change is manually verified in userspace by ensuring the
advertising manager's supported_flags field is updated with new flags on
hatch chromebook (ext advertising supported).
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here we make sure we properly report the number of supported
advertising slots when we are using hardware offloading. If no
hardware offloading is available, we default this value to
HCI_MAX_ADV_INSTANCES for use in software rotation as before.
This change has been tested on kukui (no ext adv) and hatch (ext adv)
chromebooks by verifying "SupportedInstances" shows 5 (the default) and
6 (slots supported by controller), respectively.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch defines new getsockopt options BT_SNDMTU/BT_RCVMTU
for SCO socket to be compatible with other bluetooth sockets.
These new options return the same value as option SCO_OPTIONS
which is already present on existing kernels.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Unregister_pm_notifier is a blocking call so suspend tasks should be
cleared beforehand. Otherwise, the notifier will wait for completion
before returning (and we encounter a 2s timeout on resume).
Fixes: 0e9952804e (Bluetooth: Clear suspend tasks on unregister)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
While unregistering, make sure to clear the suspend tasks before
cancelling the work. If the unregister is called during resume from
suspend, this will unnecessarily add 2s to the resume time otherwise.
Fixes: 4e8c36c3b0 (Bluetooth: Fix suspend notifier race)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net/bluetooth/sco.c: In function ‘sco_sock_setsockopt’:
net/bluetooth/sco.c:862:3: error: cannot convert to a pointer type
862 | if (get_user(opt, (u32 __user *)optval)) {
| ^~
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag CRYPTO_ALG_INTERNAL is not meant to be used outside of
the Crypto API. It isn't needed here anyway.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Increment the mgmt revision due to the recently added new commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When an LE connection is requested and an RPA update is needed via
hci_connect_le_scan, the default scanning parameters are used rather
than the connect parameters. This leads to significant delays in the
connection establishment process when using lower duty cycle scanning
parameters.
The patch simply looks at the pended connection list when trying to
determine which scanning parameters should be used.
Before:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#378 [hci0] 1659.247156
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 367.500 msec (0x024c)
Window: 37.500 msec (0x003c)
After:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#39 [hci0] 7.422109
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 60.000 msec (0x0060)
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable RPA timeout during bluetooth initialization.
The RPA timeout value is used from hdev, which initialized from
debug_fs
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In this patch if le_create_conn process is started restrict to
disable address resolution and same is disabled during
le_enh_connection_complete
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When address resolution is enabled and set_privacy is enabled let's
use own address type as 0x03
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using controller based address resolution, then the new address
types 0x02 and 0x03 are used. These types need to be converted back into
either public address or random address types.
This patch is specially during LE_CREATE_CONN if using own_add_type as 0x02
or 0x03.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the whitelist is updated, then also update the entries of the
resolving list for devices where IRKs are available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the LL Privacy support is available, then as part of enabling or
disabling passive background scanning, it is required to set up the
controller based address resolution as well.
Since only passive background scanning is utilizing the whitelist, the
address resolution is now bound to the whitelist and passive background
scanning. All other resolution can be easily done by the host stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using controller based address resolution, then the new address
types 0x02 and 0x03 are used. These types need to be converted back into
either public address or random address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The original return is NOTIFY_STOP, but notifier_call_chain would stop
the future call for register_pm_notifier even registered on other Kernel
modules with the same priority which value is zero.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.
This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.
So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.
Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.
So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.
Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.
That way we can narrow down ranges of fakes for each of them.
e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
support BT 1.1 only; so it's a dead giveaway when some
third-party BT 4.0 dongle reuses it.
So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.
Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
IC markings on 0x7558: FR3191AHAL 749H15143 (???)
https://bugzilla.kernel.org/show_bug.cgi?id=60824
Fixes: 81cac64ba2 (Deal with USB devices that are faking CSR vendor)
Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: Mike Johnson <yuyuyak@gmail.com>
Tested-by: Ricardo Rodrigues <ekatonb@gmail.com>
Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just check for a NULL method instead of wiring up
sock_no_{get,set}sockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality to disable and remove advertising instances,
and use that functionality in MGMT add/remove advertising calls.
Currently, advertising is globally-disabled, i.e. all instances are
disabled together, even if hardware offloading is available. This
patch adds functionality to disable and remove individual adv
instances, solving two issues:
1. On new advertisement registration, a global disable was done, and
then only the new instance was enabled. This meant only the newest
instance was actually enabled.
2. On advertisement removal, the structure was removed, but the instance
was never disabled or removed, which is incorrect with hardware offload
support.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Shyh-In Hwang <josephsih@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check `num_rsp` before using it as for-loop counter. Add `unlock` label.
Cc: stable@vger.kernel.org
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check `num_rsp` before using it as for-loop counter.
Cc: stable@vger.kernel.org
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Even with one advertisement monitor in place, the scan policy should use
the whitelist while the system is going to suspend to prevent waking by
random advertisement.
The following test was performed.
- With a paired device, register one advertisement monitor, suspend
the system and verify that the host was not awaken by random
advertisements.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an le_simult_central_peripheral features which allows a
clients to determine if the controller is able to support peripheral and
central connections separately and at the same time.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the kernel oops by removing unnecessary background scan
update from hci_adv_monitors_clear() which shouldn't invoke any work
queue.
The following test was performed.
- Run "rmmod btusb" and verify that no kernel oops is triggered.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes active scans to use the configured default parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When restarting LE scanning, check if it's currently paused before
enabling passive scanning.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the extended advertisement feature is enabled, a hardcoded min and
max interval of 0x8000 is used. This patch fixes this issue by using
the configured min/max value.
This was validated by setting min/max in main.conf and making sure the
right setting is applied:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen
25 #93 [hci0] 10.953011
…
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
…
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The command status reply is only for failure. When completing set system
config command, the reply has to be command complete.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If user decides to cancel the ongoing pairing process (e.g. by clicking
the cancel button on pairing/passkey window), abort any ongoing pairing
and then terminate the link if it was created because of the pair
device action.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This calls hci_update_background_scan() when there is any update on the
advertisement monitors. If there is at least one advertisement monitor,
the filtering policy of scan parameters should be 0x00. This also reports
device found mgmt events if there is at least one monitor.
The following cases were tested with btmgmt advmon-* commands.
(1) add a ADV monitor and observe that the passive scanning is
triggered.
(2) remove the last ADV monitor and observe that the passive scanning is
terminated.
(3) with a LE peripheral paired, repeat (1) and observe the passive
scanning continues.
(4) with a LE peripheral paired, repeat (2) and observe the passive
scanning continues.
(5) with a ADV monitor, suspend/resume the host and observe the passive
scanning continues.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This notifies management sockets on MGMT_EV_ADV_MONITOR_REMOVED event.
The following test was performed.
- Start two btmgmt consoles, issue a btmgmt advmon-remove command on one
console and observe a MGMT_EV_ADV_MONITOR_REMOVED event on the other.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This notifies management sockets on MGMT_EV_ADV_MONITOR_ADDED event.
The following test was performed.
- Start two btmgmt consoles, issue a btmgmt advmon-add command on one
console and observe a MGMT_EV_ADV_MONITOR_ADDED event on the other
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_REMOVE_ADV_MONITOR command.
Note that the controller-based monitoring is not yet in place. This
removes the internal monitor(s) without sending HCI traffic, so the
request returns immediately.
The following test was performed.
- Issue btmgmt advmon-remove with valid and invalid handles.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_ADD_ADV_PATTERNS_MONITOR command.
Note that the controller-based monitoring is not yet in place. This tracks
the content of the monitor without sending HCI traffic, so the request
returns immediately.
The following manual test was performed.
- Issue btmgmt advmon-add with valid and invalid inputs.
- Issue btmgmt advmon-add more the allowed number of monitors.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_READ_ADV_MONITOR_FEATURES
command. Since the controller-based monitoring is not yet in place, this
report only the supported features but not the enabled features.
The following test was performed.
- Issuing btmgmt advmon-features.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Replace the wakeable boolean with flags in hci_conn_params and all users
of this boolean. This will be used by the get/set device flags mgmt op.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the classic device list now supports flags, convert the wakeable
list into a flag on the existing device list.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to more easily add device flags to classic devices, create
a new type of bdaddr_list that supports setting flags.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the required read/set commands for runtime configuration. Even
while currently no parameters are specified, the commands are made
available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements the read default system parameters and the set
default system parameters mgmt commands.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch centralized the initialization of default parameters. This
is required to allow clients to more easily customize the default
system parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change implements suggestions from the code review of the SCO CMSG
state flag patch.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds support for reporting the BT_PKT_STATUS to the socket
CMSG data to allow the implementation of a packet loss correction on
erroneous data received on the SCO socket.
The patch was partially developed by Marcel Holtmann and validated by
Hsin-yu Chao.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It is preferable to allow suspend even when Bluetooth has problems
preparing for sleep. When Bluetooth fails to finish preparing for
suspend, log the error and allow the suspend notifier to continue
instead.
To also make it clearer why suspend failed, change bt_dev_dbg to
bt_dev_err when handling the suspend timeout.
Fixes: dd522a7429 ("Bluetooth: Handle LE devices during suspend")
Reported-by: Len Brown <len.brown@intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
This patch removes a particularly noisy dbg message. The debug message
isn't particularly interesting for debuggability so it was simply
removed to reduce noise in dbg logs.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check current scan state by checking HCI_LE_SCAN flag and send scan
disable command only if scan is already enabled.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There was a lockdep which led to commit
fad003b6c8 ("Bluetooth: Fix inconsistent lock state with RFCOMM")
Lockdep noticed that `sk->sk_lock.slock' was acquired without disabling
the softirq while the lock was also used in softirq context.
Unfortunately the solution back then was to disable interrupts before
acquiring the lock which however made lockdep happy.
It would have been enough to simply disable the softirq. Disabling
interrupts before acquiring a spinlock_t is not allowed on PREEMPT_RT
because these locks are converted to 'sleeping' spinlocks.
Use spin_lock_bh() in order to acquire the `sk_lock.slock'.
Reported-by: Luis Claudio R. Goncalves <lclaudio@uudg.org>
Reported-by: kbuild test robot <lkp@intel.com> [missing unlock]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
EIR flags should just hint if SSP may be supported but we shall verify
this with use of the actual features as the SSP bits may be disabled in
the lower layers which would result in legacy authentication to be
used.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection
state is BT_CONFIG so callers don't have to check the state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth PTS test case HFP/AG/ACC/BI-12-I accepts SCO connection
with invalid parameter at the first SCO request expecting AG to
attempt another SCO request with the use of "safe settings" for
given codec, base on section 5.7.1.2 of HFP 1.7 specification.
This patch addresses it by adding "Invalid LMP Parameters" (0x1e)
to the SCO fallback case. Verified with below log:
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 13
Setting: 0x0003
Input Coding: Linear
Input Data Format: 1's complement
Input Sample Size: 8-bit
# of bits padding at MSB: 0
Air Coding Format: Transparent Data
Retransmission effort: Optimize for link quality (0x02)
Packet type: 0x0380
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) ncmd 1
Status: Success (0x00)
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 256
Count: 1
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
Status: Invalid LMP Parameters / Invalid LL Parameters (0x1e)
Handle: 0
Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC)
Link type: eSCO (0x02)
Transmission interval: 0x00
Retransmission window: 0x02
RX packet length: 0
TX packet length: 0
Air mode: Transparent (0x03)
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 8
Setting: 0x0003
Input Coding: Linear
Input Data Format: 1's complement
Input Sample Size: 8-bit
# of bits padding at MSB: 0
Air Coding Format: Transparent Data
Retransmission effort: Optimize for link quality (0x02)
Packet type: 0x03c8
EV3 may be used
2-EV3 may not be used
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) ncmd 1
Status: Success (0x00)
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 5
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
Status: Success (0x00)
Handle: 257
Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC)
Link type: eSCO (0x02)
Transmission interval: 0x06
Retransmission window: 0x04
RX packet length: 30
TX packet length: 30
Air mode: Transparent (0x03)
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-05-13
Here's a second attempt at a bluetooth-next pull request which
supercedes the one dated 2020-05-09. This should have the issues
discovered by Jakub fixed.
- Add support for Intel Typhoon Peak device (8087:0032)
- Add device tree bindings for Realtek RTL8723BS device
- Add device tree bindings for Qualcomm QCA9377 device
- Add support for experimental features configuration through mgmt
- Add driver hook to prevent wake from suspend
- Add support for waiting for L2CAP disconnection response
- Multiple fixes & cleanups to the btbcm driver
- Add support for LE scatternet topology for selected devices
- A few other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever we disconnect a L2CAP connection, we would immediately
report a disconnection event (EPOLLHUP) to the upper layer, without
waiting for the response of the other device.
This patch offers an option to wait until we receive a disconnection
response before reporting disconnection event, by using the "how"
parameter in l2cap_sock_shutdown(). Therefore, upper layer can opt
to wait for disconnection response by shutdown(sock, SHUT_WR).
This can be used to enforce proper disconnection order in HID,
where the disconnection of the interrupt channel must be complete
before attempting to disconnect the control channel.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After sending Inquiry Cancel command to the controller, it is possible
that Inquiry Complete event comes before Inquiry Cancel command complete
event. In this case the Inquiry Cancel command will have status of
Command Disallowed since there is no Inquiry session to be cancelled.
This case should not be treated as error, otherwise we can reach an
inconsistent state.
Example of a btmon trace when this happened:
< HCI Command: Inquiry Cancel (0x01|0x0002) plen 0
> HCI Event: Inquiry Complete (0x01) plen 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4
Inquiry Cancel (0x01|0x0002) ncmd 1
Status: Command Disallowed (0x0c)
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Let drivers have a hook to disable configuring scanning during suspend.
Drivers should use the device_may_wakeup function call to determine
whether hci should be configured for wakeup.
For example, an implementation for btusb may look like the following:
bool btusb_prevent_wake(struct hci_dev *hdev)
{
struct btusb_data *data = hci_get_drvdata(hdev);
return !device_may_wakeup(&data->udev->dev);
}
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Renamed BT_SUSPEND_COMPLETE to BT_SUSPEND_CONFIGURE_WAKE since it sets
up the event filter and whitelist for wake-up.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a device is suspended, it doesn't need to be as responsive to
connection events. Increase the interval to 640ms (creating a duty cycle
of roughly 1.75%) so that passive scanning uses much less power (vs
previous duty cycle of 18.75%). The new window + interval combination
has been tested to work with HID devices (which are currently the only
devices capable of wake up).
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The types for window and interval should be uint16, not uint8.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case dynamic debug is disabled, this feature allows a vendor platform
to provide debug statement printing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To enable platform specific experimental features, introduce this new set of
management commands and events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The security manager operates on a specific controller and thus use
bt_dev_dbg to indetify the controller for each debug message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When setting HCI_MGMT_HDEV_OPTIONAL it is possible to target a specific
conntroller or a global interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The majority of management interaction are based on a controller index
and have a hci_dev associated with it. So use bt_dev_dbg to have a clean
way of indentifying the controller the debug message belongs to.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The event MGMT_EV_PHY_CONFIGURATION_CHANGED wasn't listed in the list of
supported events. So add it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix 2 typos in L2CAP_CREDIT_BASED_CONNECTION_REQ (0x17) handling function, that
cause BlueZ answer with L2CAP_CR_LE_INVALID_PARAMS or L2CAP_CR_LE_INVALID_SCID
error on a correct ECRED connection request.
Enchanced Credit Based Mode support was recently introduced with the commit
15f02b9105 ("Bluetooth: L2CAP: Add initial code
for Enhanced Credit Based Mode").
Signed-off-by: Konstantin Forostyan <konstantin.forostyan@peiker-cee.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix the advertising handle is set to 0 regardless of actual
instance value. The affected commands are LE Set Advertising Set Random
Address, LE Set Extended Advertising Data, and LE Set Extended Scan
Response Data commands.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of manually allocating a 'struct shash_desc' on the stack and
calling crypto_shash_digest(), switch to using the new helper function
crypto_shash_tfm_digest() which does this for us.
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch reverts the folowing commits:
commit 064ff66e2b
"bonding: add missing netdev_update_lockdep_key()"
commit 53d374979e
"net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()"
commit 1f26c0d3d2
"net: fix kernel-doc warning in <linux/netdevice.h>"
commit ab92d68fc2
"net: core: add generic lockdep keys"
but keeps the addr_list_lock_key because we still lock
addr_list_lock nestedly on stack devices, unlikely xmit_lock
this is safe because we don't take addr_list_lock on any fast
path.
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows scatternet connections to be created if the
controller reports support and the HCI_QUIRK_VALID_LE_STATES indicates
that the reported LE states can be trusted.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Enhanced Connection Complete event is use in conjunction with LL
Privacy and not Extended Advertising.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When starting active scanning for discovery the whitelist is not needed
to be used. So the filter_policy is 0x00. To make the core more readable
use a variable name instead of just setting 0 as paramter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The error could indicate a problem with the Bluetooth device. It
is easier to investigate if the packet's actual length gets logged,
not just the fact that a discrepancy occurred.
Signed-off-by: Daniels Umanovskis <du@axentia.se>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To improve security, always give the user-space daemon a chance to
accept or reject a Just Works pairing (LE). The daemon may decide to
auto-accept based on the user's intent.
This patch is similar to the previous patch but applies for LE Secure
Connections (SC).
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some static checker run by 0day reports a variableScope warning.
net/bluetooth/smp.c:870:6: warning:
The scope of the variable 'err' can be reduced. [variableScope]
There is no need for two separate variables holding return values.
Stick with the existing variable. While at it, don't pre-initialize
'ret' because it is set in each code path.
tk_request() is supposed to return a negative error code on errors,
not a bluetooth return code. The calling code converts the return
value to SMP_UNSPECIFIED if needed.
Fixes: 92516cd97f ("Bluetooth: Always request for user confirmation for Just Works")
Cc: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BT qualification test SM/MAS/PKE/BV-01-C needs us to turn off
the MITM flag when pairing, and at the same time also set the io
capability to something other than no input no output.
Currently the MITM flag is only unset when the io capability is set
to no input no output, therefore the test cannot be executed.
This patch introduces a debugfs option to force MITM flag to be
turned off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added new commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To allow userspace to make correcty security policy decision, the kernel
needs to export a few details of the supported security features and
encryption key size information. This command exports this information
and also allows future extensions if needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Micrsoft defined a set for HCI vendor extensions. Check the following
link for details:
https://docs.microsoft.com/en-us/windows-hardware/drivers/bluetooth/microsoft-defined-bluetooth-hci-commands-and-events
This provides the basic framework to enable the extension and read its
supported features. Drivers still have to declare support for this
extension before it can be utilized by the host stack.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is just a cosmetic clean to move the selftests configuration option
to the bottom of the list of options.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When scheduling TX packets, send all SCO/eSCO packets first, check for
pending SCO/eSCO packets after every ACL/LE packet and send them if any
are pending. This is done to make sure that we can meet SCO deadlines
on slow interfaces like UART.
If we were to queue up multiple ACL packets without checking for a SCO
packet, we might miss the SCO timing. For example:
The time it takes to send a maximum size ACL packet (1024 bytes):
t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
where 10/8 is uart overhead due to start/stop bits per byte
Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666.
At a baudrate of 3000000, if we didn't check for SCO packets within 1024
bytes, we would miss the 3.75ms timing window.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To improve security, always give the user-space daemon a chance to
accept or reject a Just Works pairing (LE). The daemon may decide to
auto-accept based on the user's intent.
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds BT_MODE socket option which can be used to set L2CAP modes,
including modes only supported over LE which were not supported using
the L2CAP_OPTIONS.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
L2CAP_OPTIONS shall only be used with BR/EDR modes.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses the DEFER_SETUP flag to group channels with
L2CAP_CREDIT_BASED_CONNECTION_REQ.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this change, the encryption key size is not assumed to be 16 if the
read_encryption_key_size command fails for any reason. This ensures
that if the controller fails the command for any reason that the
encryption key size isn't implicitely set to 16 and instead take a more
concervative posture to assume it is 0.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a callback to read the socket pid.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When handling auto-connected devices, we should execute the rest of the
connection complete when it was previously discovered and it is an ACL
connection.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If Bluetooth fails to enter the suspended state correctly, restore the
state to running (re-enabling scans). PM_POST_SUSPEND is only sent to
notifiers that successfully return from PM_PREPARE_SUSPEND notification
so we should recover gracefully if it fails.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BlueZ cancels adv when starting a scan, but does not cancel a scan when
starting to adv. Neither is required, so this brings both to a
consistent state (of not affecting each other). Some very rare (I've
never seen one) BT 4.0 chips will fail to do both at once. Even this is
ok since the command that will fail will be the second one, and thus the
common sense logic of first-come-first-served is preserved for BLE
requests.
Signed-off-by: Dmitry Grinberg <dmitrygr@google.com>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
net/bluetooth/l2cap_core.c: In function l2cap_ecred_conn_req:
net/bluetooth/l2cap_core.c:5848:6: warning: variable credits set but not used [-Wunused-but-set-variable]
commit 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
involved this unused variable, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Smatch complains about the indenting:
net/bluetooth/l2cap_sock.c:1027 l2cap_sock_recvmsg()
warn: inconsistent indenting
It looks like this is supposed to be an "else if" condition.
Fixes: 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In bluetooth core specification 4.2,
Vol 2, Part E, 7.8.9 LE Set Advertise Enable Command, it says
The Controller shall continue advertising until ...
or until a connection is created or ...
In these cases, advertising is then disabled.
Hence, advertising would be disabled before a connection is
established. In current kernel implementation, advertising would
be re-enabled when all connections are terminated.
The correct disconnection flow looks like
< HCI Command: Disconnect
> HCI Event: Command Status
Status: Success
> HCI Event: Disconnect Complete
Status: Success
Specifically, the last Disconnect Complete Event would trigger a
callback function hci_event.c:hci_disconn_complete_evt() to
cleanup the connection and re-enable advertising when proper.
However, sometimes, there might occur an exception in the controller
when disconnection is being executed. The disconnection flow might
then look like
< HCI Command: Disconnect
> HCI Event: Command Status
Status: Unknown Connection Identifier
Note that "> HCI Event: Disconnect Complete" is missing when such an
exception occurs. This would result in advertising staying disabled
forever since the connection in question is not cleaned up correctly.
To fix the controller exception issue, we need to do some connection
cleanup when the disconnect command status indicates an error.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To prevent spurious wake ups, we disable any discovery or advertising
when we enter suspend and restore it when we exit suspend. While paused,
we disable any management requests to modify discovery or advertising.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To handle LE devices, we must first disable passive scanning and
disconnect all connected devices. Once that is complete, we update the
whitelist and re-enable scanning
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To handle BR/EDR devices, we first disable page scan and disconnect all
connected devices. Once that is complete, we add event filters (for
devices that can wake the system) and re-enable page scan.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Register for PM_SUSPEND_PREPARE and PM_POST_SUSPEND to make sure the
Bluetooth controller is prepared correctly for suspend/resume. Implement
the registration, scheduling and task handling portions only in this
patch.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If an error occurs during request building in add_advertising(),
remember to send MGMT_STATUS_FAILED command status back to bluetoothd.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change fixes the off by one error in the erroneous command bit
masks which can lead to the erroneous data commands being sent to a
controller that doesn't support them.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the RPA generation fails, indicate the error with a device specifc
error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This should make it safe to have the code upstream without affecting
stable systems since there are a few details not sort out with ECRED
mode e.g: how to initiate multiple connections at once.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds the initial code for Enhanced Credit Based Mode which
introduces a new socket mode called L2CAP_MODE_EXT_FLOWCTL, which for
the most part work the same as L2CAP_MODE_LE_FLOWCTL but uses different
PDUs to setup the connections and also works over BR/EDR.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added setting and
command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull when parsing signalling PDUs so skb->data for
pointing to the current PDU and skb->len as the remaining bytes to be
processed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When processing SCO packets, the handle is wrongly assumed as 16-bit
value. The actual size is 12-bits and the other 4-bits are used for
packet flags.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
