Sathya Perla says:
====================
be2net: patch set
Patch 1/2 is a v2 of a patch that was submitted earlier (as a part of a
different patch-set). v2 incorporates a suggestion given by David Laight
for how long to poll for pending TX completions while disabling a device.
Patch 2/2 fixes a crash in be_remove()->be_close()
path after be2net has aborted an EEH error recovery
due to a permanant failure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the EEH error recovery path, when a permanent failure occurs,
we clean up adapter structure (i.e. destroy queues etc) by calling
be_clear() and return PCI_ERS_RESULT_DISCONNECT.
After this the stack tries to remove device from bus and calls
be_remove() which invokes netdev_unregister()->be_close().
be_close() operating on destroyed queues results in a
NULL dereference.
This patch fixes this problem by introducing a flag to keep track
of the setup state.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_close() currently waits for a max of 200ms to receive all pending
TX compls. This timeout value was roughly calculated based on 10G
transmission speeds and the TX queue depth. This timeout may not be
enough when the link is operating at lower speeds or in multi-channel/SR-IOV
configs with TX-rate limiting setting.
It is hard to calculate a "proper timeout value" that works in all
configurations. This patch solves this problem by continuing to reap
TX completions till the HW is completely silent for a period of 10ms or
a HW error is detected.
v2: implements the new scheme (as suggested by David Laight) instead of
just waiting longer than 200ms for reaping all completions.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tag next-20140407, building with CONFIG_DEBUG_SECTION_MISMATCH
enabled, the following WARNING is occured:
WARNING: drivers/built-in.o(.text.unlikely+0x2220): Section mismatch
in reference from the function __reserved_mem_check_root() to the
function .init.text:of_get_flat_dt_prop()
The function __reserved_mem_check_root() references
the function __init of_get_flat_dt_prop().
This is often because __reserved_mem_check_root lacks a __init
annotation or the annotation of of_get_flat_dt_prop is wrong.
WARNING: vmlinux.o(.text.unlikely+0xb9d0): Section mismatch in reference
from the function __reserved_mem_check_root() to the (unknown reference)
.init.data:(unknown)
The function __reserved_mem_check_root() references
the (unknown reference) __initdata (unknown).
This is often because __reserved_mem_check_root lacks a __initdata
annotation or the annotation of (unknown) is wrong.
This is cause by :
'drivers: of: add initialization code for dynamic reserved memory'.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Using "digi" for Digi International Inc.
Additionally, this patch keep "dlink" entry sorted alphabetically.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a number of eeproms and temperature sensors/fan controllers used
by kirkwood boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a number of vendor prefixes by kirkwood devices. These are not all
stock tickers, but have been in use for a while so changing would not
be easy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Fix in commit [1] is not sufficient since a deferred VF initialization
could happen after pci_enable_sriov() is finished, but before the PF is
fully initialized.
Need to prevent VFs from initializing till the PF is fully ready and
comm channel is operational.
[1] - 9798935 "net/mlx4_core: mlx4_init_slave() shouldn't access comm
channel before PF is ready"
CC: Stuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell Kirkwood SoC binding have not yet been documented. Add the
documentation including the supported SoCs and boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Newhaven Display provides the worldwide marketplace with cost
effective high quality display devices ranging from OLED and LCD
Displays to VFD Displays.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Rob Herring <robh@kernel.org>
This trivial patch adds ISEE 2007 S.L. to the list of
devicetree vendor prefixes.
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Rob Herring <robh@kernel.org>
When CONFIG_PM_SLEEP isn't enabled, bnx2_suspend/resume are unused; don't
build them when they aren't used.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Francois reported that setting big mtu on loopback device could prevent
tcp sessions making progress.
We do not support (yet ?) IPv6 Jumbograms and cook corrupted packets.
We must limit the IPv6 MTU to (65535 + 40) bytes in theory.
Tested:
ifconfig lo mtu 70000
netperf -H ::1
Before patch : Throughput : 0.05 Mbits
After patch : Throughput : 35484 Mbits
Reported-by: Francois WELLENREITER <f.wellenreiter@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid colision with regmap's struct reg_field definition by renaming
omapdss's struct reg_field to dispc_reg_field, and moving it inside
dispc.c as that's the only place it is used.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pixelclock unit change from kHz to Hz should be taken into account
in CTS value calculations in hdmi_compute_acr().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
udelay with more than 20000 may cause __bad_udelay.
Use mdelay for instead.
[fixed a typo spotted by Clemens -- tiwai]
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DSS uses shared irq handlers for DISPC and DSI, because on OMAP3, the
DISPC and DSI share the same irq line.
However, the irq handlers presume that the hardware is enabled, which,
in theory, may not be the case with shared irq handlers. So if an
interrupt happens while the DISPC/DSI is off, the kernel will halt as
the irq handler tries to access the DISPC/DSI registers.
In practice that should never happen, as both DSI and DISPC are in the
same power domain. So if there's an IRQ for one of them, the other is
also enabled. However, if CONFIG_DEBUG_SHIRQ is enabled, the kernel will
generate a spurious IRQ, which then causes the problem.
This patch adds an is_enabled field for both DISPC and DSI, which is
used to track if the HW is enabled. For DISPC the code is slightly more
complex, as the users of DISPC can register the interrupt handler, and
we want to hide the is_enabled handling from the users of DISPC.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
FB driver uses lowlevel controls for LCD powering and contrast changing.
Since LCD class cannot be used as an optional feature and should be
compiled for using in the driver, this patch selects LCD_CLASS_DEVICE
symbol for the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
"clk: divider: fix rate calculation for fractional rates" patch (and
similar for TI specific divider) fixes the clk-divider's rounding. This
patch updates the DSS driver to round the rates accordingly.
This fixes the DSS's warnings about clock rate mismatch, and also fixes
the wrong fclk rate being set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
The casting to (u16 *) on info->pseudo_palette is wrong and causes the
display to show a blue (garbage) vertical line on every other pixel column
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull liblockdep fixes from Sasha Levin:
" 1. There was a build breakage caused by marking a function 'asmlinkage'
in lockdep.h. Fix that by ignoring asmlinkage and visible annotations.
2. Josh Boyer mentioned that Fedora would like to include liblockdep
as a package, so we had to fix our versioning methods from being dumb
and pointless to something actually usable. So now liblockdep.so tracks
the kernel version which makes lives of distro folks much easier. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
perf stat did initialize the stats structure used to compute
stddev etc. incorrectly. It merely zeroes it. But one member
(min) needs to be set to a non zero value. This causes min
to be not computed at all. Call init_stats() correctly.
It doesn't matter for stat currently because it doesn't use
min, but it's still better to do it correctly.
The other users of statistics are already correct.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1395768699-16060-1-git-send-email-andi@firstfloor.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Currently,
$ perf bench numa mem
errors out with usage information. To make this more user-friendly, let
us provide a minimum set of default values required for a test
run. As an added bonus,
$ perf bench all
now goes all the way to completion.
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395964219-22173-2-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
At the end of
$ perf bench all
the program segfaults because it attempts to dereference a NULL
pointer. Fix this fault.
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395964219-22173-4-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The dwarf_getcfi() only checks .debug_frame section for CFI, but as
most binaries only have .eh_frame it'd return NULL and it makes
some variables inaccessible.
Using dwarf_getcfi_elf (along with dwarf_getelf()) allows to show and
add probe to more variables.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/1396854348-9296-1-git-send-email-namhyung@kernel.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
As Namhyung reported(https://lkml.org/lkml/2014/4/1/89),
current perf-probe -L option doesn't handle errors in line-range
searching correctly. It causes a SEGV if an error occured in the
line-range searching.
----
$ perf probe -x ./perf -v -L map__load
Open Debuginfo file: /home/namhyung/project/linux/tools/perf/perf
fname: util/map.c, lineno:153
New line range: 153 to 2147483647
path: (null)
Segmentation fault (core dumped)
----
This is because line_range_inline_cb() ignores errors
from find_line_range_by_line() which means that lr->path is
already freed on the error path in find_line_range_by_line().
As a result, get_real_path() accesses the lr->path and it
causes a NULL pointer exception.
This fixes line_range_inline_cb() to handle the error correctly,
and report it to the caller.
Anyway, this just fixes a possible SEGV bug, Namhyung's patch
is also required.
Reported-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20140402054831.19080.27006.stgit@ltc230.yrl.intra.hitachi.co.jp
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The commit 5a62257a3d ("perf probe: Replace line_list with
intlist") replaced line_list to intlist but it has a problem that if a
same line was added again, it'd return -EEXIST rather than 1.
Since line_range_walk_cb() only checks the result being negative, it
resulted in failure or segfault sometimes.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/1396327677-3657-1-git-send-email-namhyung@kernel.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The Makefile logic sets FEATURE_CHECKS_CFLAGS-libdw-dwarf-unwind and
FEATURE_CHECKS_LDFLAGS-libdw-dwarf-unwind only if LIBDW_DIR is
defined. This means that under a normal setup,
$ make NO_LIBUNWIND=1
won't automatically pick up libdw. Fix this.
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Acked-by: Jean Pihet <jean.pihet@linaro.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395873845-466-1-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Leaving ghostprotocols.net for old networking stuff.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-jott6d40nkjjc3vvh3vw53lp@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
I.e. do the same as when NO_LIBELF is explicitely passed in the 'make'
command line, fixing this:
Auto-detecting system features:
... dwarf: [ OFF ]
... glibc: [ on ]
... gtk2: [ OFF ]
... libaudit: [ OFF ]
... libbfd: [ OFF ]
... libelf: [ OFF ]
... libunwind: [ OFF ]
... libdw-dwarf-unwind: [ OFF ]
... DWARF post unwind library: libdw
<SNIP>
CC /tmp/build/perf/util/symbol-minimal.o
CC /tmp/build/perf/util/unwind-libdw.o
arch/x86/util/unwind-libdw.c:1:30: fatal error: elfutils/libdwfl.h: No such file or directory
compilation terminated.
CC /tmp/build/perf/tests/keep-tracking.o
util/unwind-libdw.c:2:28: fatal error: elfutils/libdw.h: No such file or directory
compilation terminated.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-e39j1yxanltjx4t0msse63ax@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The patch 3a3ffa2e82 ("tools lib traceevent: Report better error
message on bad function args") added the error message but it seems
there's no reason to call warning() directly.
So change it to do_warning_event() to provide event information too.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1395192174-26273-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
It's sometimes useful to know where the parse failure was occurred. Add
do_warning_event() macro to see the failing event.
It now shows the messages like below:
$ perf test 5
5: parse events tests : Warning: [kvmmmu:kvm_mmu_get_page] bad op token {
Warning: [kvmmmu:kvm_mmu_sync_page] bad op token {
Warning: [kvmmmu:kvm_mmu_unsync_page] bad op token {
Warning: [kvmmmu:kvm_mmu_prepare_zap_page] bad op token {
Warning: [kvmmmu:fast_page_fault] function is_writable_pte not defined
Warning: [xen:xen_mmu_ptep_modify_prot_commit] function sizeof not defined
Warning: [xen:xen_mmu_ptep_modify_prot_start] function sizeof not defined
Warning: [xen:xen_mmu_set_pgd] function sizeof not defined
Warning: [xen:xen_mmu_set_pud] function sizeof not defined
Warning: [xen:xen_mmu_set_pmd] function sizeof not defined
...
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1395192174-26273-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
On perf top, the -s option is used for --sort, but the man page
contains invalid documentation of -s option for --sym-annotate.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1395193578-27098-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
When we build an already built kernel again, arch/x86/syscalls/Makefile
and arch/x86/tools/Makefile emits "Nothing to be done for ..."
messages.
Here is the command log:
$ make defconfig
[ snip ]
$ make
[ snip ]
$ make
make[1]: Nothing to be done for `all'. <-----
make[1]: Nothing to be done for `relocs'. <-----
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
Besides not emitting those, "all" and "relocs" should be added to PHONY as well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Acked-by: Michal Marek <mmarek@suse.cz>
Link: http://lkml.kernel.org/r/1397093742-11144-1-git-send-email-yamada.m@jp.panasonic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
omap_fbdev_create() takes a reference to the fb's gem object with
omap_gem_get_paddr(). However, it never releases it with
omap_gem_put_paddr().
This patch adds the missing omap_gem_put_paddr() to omap_fbdev_free().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Plane rotation with omapdrm is currently broken.
It seems omap_plane_mode_set() expects width and height in screen
coordinates, so pass it like that.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment the omap_crtc_pre_apply() handles the enabling, disabling
and configuring of encoders and panels separately from the CRTC (i.e.
the overlay manager).
However, this doesn't work correctly. The encoder driver has to be in
control of its video input (i.e. the crtc) for correct operation.
This problem causes bugs with (at least) HDMI: the HDMI encoder supplies
pixel clock for DISPC, and DISPC supplies video stream for HDMI. The
current code first enables the HDMI encoder, and CRTC after that.
However, the encoder expects the video stream to start during the
encoder's enable, and if it doesn't, there will be sync lost errors.
The encoder enables its video source by calling src->enable(), and this
call goes to omapdrm (omap_crtc_enable), but omapdrm doesn't do anything
in that function. Similarly for disable, which goes to
omap_crtc_disable().
This patch moves the code to setup and enable/disable the crtc to
omap_crtc_enable. and omap_crtc_disable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When an encoder is no longer connected to a crtc, the driver will leave
the encoder enabled.
This patch adds code to track the encoder used for a crtc, and when the
encoder changes, the old one is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At module unload, omap_fbdev_free() gets called which releases the
framebuffers. However, the framebuffers are still used by crtcs, and
will be released only later at vsync. The driver doesn't wait for this,
and goes on to release the rest of the resources, which often
causes a crash.
This patchs adds a omap_crtc_flush() function which waits until the crtc
has finished with its apply queue and page flips.
The function utilizes a simple polling while-loop, as the performance is
not an issue here.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At the moment the DMM driver is never unregistered, even if it's
registered in the omapdrm module's init function. This means we'll get
errors when reloading the omapdrm module.
Fix this by unregistering the DMM driver properly, and also change the
module init to fail if DMM driver cannot be registered, simplifying the
unregister path as we don't need to keep the state whether we registered
the DMM driver or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When unloading omapdrm driver, the omapdrm platform device is
uninitialized last, after the displays have been disconnected omap_crtc
callbacks have been removed. As the omapdrm pdev uninitialization needs
the features uninitialized in earlier steps, a crash is guaranteed.
This patch fixes the uninitialize order so that the omapdrm pdev is
removed first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At the moment it's quite easy to get the following errors when the HDMI
output is enabled or disabled:
[drm:omap_crtc_error_irq] *ERROR* tv: errors: 00008000
The reason for the errors is that the omapdrm driver doesn't properly
handle the sync-lost irqs that happen when enabling the DIGIT crtc,
which is used for HDMI and analog TV. The driver does disable the
sync-lost irq properly, but it fails to wait until the output has been
fully enabled (i.e. the first vsync), so the sync-lost errors are still
seen occasionally.
This patch makes the omapdrm act the same way as the omapfb does:
- When enabling a display, we'll wait for the first vsync.
- When disabling a display, we'll wait for framedone if available, or
odd and even vsyncs.
These changes make sure the output is fully enabled or disabled at the
end of the function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Sanjay Singh Rawat <sanjay.rawat@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
nft_cmp_fast is used for equality comparisions of size <= 4. For
comparisions of size < 4 byte a mask is calculated that is applied to
both the data from userspace (during initialization) and the register
value (during runtime). Both values are stored using (in effect) memcpy
to a memory area that is then interpreted as u32 by nft_cmp_fast.
This works fine on little endian since smaller types have the same base
address, however on big endian this is not true and the smaller types
are interpreted as a big number with trailing zero bytes.
The mask therefore must not include the lower bytes, but the higher bytes
on big endian. Add a helper function that does a cpu_to_le32 to switch
the bytes on big endian. Since we're dealing with a mask of just consequitive
bits, this works out fine.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
