The SM8150 MTP board does not have magically different GPU than the
SM8150, so it cannot use amd,imageon compatible, also pointed by
dtbs_check:
sm8150-mtp.dtb: gpu@2c00000: compatible: 'oneOf' conditional failed, one must be fixed:
['qcom,adreno-640.1', 'qcom,adreno', 'amd,imageon'] is too long
'qcom,adreno-640.1' does not match '^qcom,adreno-[0-9a-f]{8}$'
'qcom,adreno-640.1' does not match '^amd,imageon-200\\.[0-1]$'
'amd,imageon' was expected
The incorrect amd,imageon compatible was added in commit f30ac26def
("arm64: dts: qcom: add sm8150 GPU nodes") to the SM8150 and later moved
to the SM8150 MTP board in commit 1642ab96ef ("arm64: dts: qcom:
sm8150: Don't start Adreno in headless mode") with an intention to allow
headless mode. This should be solved via proper driver quirks, not fake
compatibles.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821140116.436441-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
X1E80100 has a multiport controller with 2 HS (eUSB) and 2 SS PHYs
attached to it. It's commonly used for USB-A ports and internally
routed devices. Configure it to support such functionality.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240820-topic-h_mp-v2-2-d88518066372@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The fastrpc driver uses the label to determine the domain ID and create
the device nodes. It should be "cdsp1" as this is the engine we use here.
Fixes: df54dcb34f ("arm64: dts: qcom: sa8775p: add ADSP, CDSP and GPDSP nodes")
Reported-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240816102345.16481-2-brgl@bgdev.pl
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
IPQ SoCs dont involve RPM in managing NoC related clocks and
there is no NoC scaling. Linux itself handles these clocks.
However, these should not be exposed as just clocks and align
with other Qualcomm SoCs that handle these clocks from a
interconnect provider.
Hence include icc provider capability to the gcc node so that
peripherals can use the interconnect facility to enable these
clocks. Change USB to use the icc-clk framework for the iface
clock.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/20240730054817.1915652-6-quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Move lpass codecs va and wsa macros to use the clks directly from
AFE clock controller instead of going via gfm mux like other codec macros
and SoCs.
This makes it more align with the other SoCs and codec macros in this SoC
which take AFE clocks directly. This will also avoid an extra clk mux layer,
provides consistency and avoids the buggy mux driver which will be removed.
This should also fix RB5 audio.
Remove the gfm mux drivers for both audiocc and aoncc.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240815170542.20754-1-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support for the LPASS (Q6) SMMU and keep it disabled as this is
used only when the audio DSP is present and used, which is not
mandatory to have.
It is expected for board-specific device-trees to enable this node
if supported.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Link: https://lore.kernel.org/r/20240814-lpass-v1-3-a5bb8f9dfa8b@freebox.fr
[bjorn: s/iface/bus in clock-names, to match binding]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a pshold restart node what can be found in downstream for
enable to perform restart operations.
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20240807-pshold-v1-1-0fa7927e99ce@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the correct panel compatible, and wire up enable-gpio. It is wired
up in the same way as the x1e80100-crd.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20240806202218.9060-1-robdclark@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the main RGB sensor on the Lenovo x13s a five megapixel 2 lane DPHY
MIPI sensor connected to cisphy0.
With the pm8008 patches recently applied to the x13s dtsi we can now also
enable the RGB sensor. Once done we have all upstream support necessary for
the RGB sensor on x13s.
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240806-b4-linux-next-24-07-31-camss-sc8280xp-lenovo-rgb-v2-v3-1-199767fb193d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable all remoteproc nodes on the sa8775p-ride board and point to the
appropriate firmware files.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240805-topic-sa8775p-iot-remoteproc-v4-6-86affdc72c04@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The dts and dtsi add support for msm8916 variant of Samsung Galaxy J3
SM-J320YZ smartphone released in 2016.
Add a device tree for SM-J320YZ with initial support for:
- GPIO keys
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5703 MUIC)
- WCNSS (WiFi/BT)
- Regulators
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
- Touchscreen
- Accelerometer
There are different variants of J3, with some differences in MUIC, sensor,
NFC and touch key I2C buses.
The common parts are shared in msm8916-samsung-j3-common.dtsi to reduce
duplication.
Signed-off-by: Lin, Meng-Bo <linmengbo06890@proton.me>
Link: https://lore.kernel.org/r/20240804065854.42437-3-linmengbo06890@proton.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On SM8350 platform the DSI internally is using the refgen regulator. Add
corresponding device node and link it as a supply to the DSI node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240804-sm8350-fixes-v1-10-1149dd8399fe@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Aside from the MDSS<->MEM interconnect, display devices have separate
interconnect for register access. Add this interconnect to the display
node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240804-sm8350-fixes-v1-9-1149dd8399fe@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SC7180/SM7125 SoCs have a special pin for UFS reset. Generally, this
pin is the same for all devices on the same SoC because it is hardcoded
in the pinctrl driver. Therefore, it might seem appropriate to add this
pin configuration in sc7180.dtsi. However, this pin is defined in the
device-specific DTS files instead of the SoC-level DTS files in all
Qualcomm DTS. To maintain consistency with this approach, we will follow
the same style.
Add reset-gpios to ufs_mem_hc.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Link: https://lore.kernel.org/r/20240731182412.27966-1-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add CPU and LLCC BWMON nodes and their corresponding opp tables for
SA8775p SoC.
SA8775p has two cpu clusters, with each cluster having a set of
CPU-to-LLCC BWMON registers. Consequently, there are two sets of
CPU-to-LLCC registers.
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Link: https://lore.kernel.org/r/20240730-add_sa8775p_bwmon-v1-2-f4f878da29ae@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The phone has a Silergy SY7802 flash LED controller.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Link: https://lore.kernel.org/r/20240729-sy7802-v6-1-86bb9083e40b@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Rename qdss@88800000 memory region as qlink_logging memory region
and add qdss_mem memory region at address of 0x88500000,
qlink_logging is being added at the memory region at the address
of 0x88800000 as the region is being used by modem firmware.
Since different DSM region size is required for different modem
firmware, split mpss_dsmharq_mem region into 2 separate regions.
This would provide the flexibility to remove the region which is
not required for a particular platform. Based on the modem firmware
either both the regions have to be used or only mpss_dsm_mem has
to be used. Also, reduce the size of mpssadsp_mem region.
Signed-off-by: Naina Mehta <quic_nainmeht@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240709064924.325478-4-quic_nainmeht@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The multiport USB controller in the SA8295P ADP is connected to four USB
Type-A ports. VBUS for each of these ports are provided by a
TPS2559QWDRCTQ1 regulator, controlled from PMIC GPIOs.
Add the necessary regulators and GPIO configuration to power these.
It seems reasonable that these regulators should be referenced as vbus
supply of usb-a-connector nodes and controlled by e.g. dwc3, but as this
is not supported in Linux today the regulators are left always-on for
now.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240707085624.3411961-1-quic_kriskura@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Existing way of allocating ports dynamically is linear starting from 1 to
MAX_PORTS. This will not work for x1e80100 as the master ports are
are not mapped in the same order.
Without this fix only one speaker in a pair of speakers will function.
After this fix along with WSA codec changes both the speakers starts
working.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240626-port-map-v2-6-6cc1c5608cdd@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Existing way of allocating ports dynamically is linear starting from 1 to
MAX_PORTS. This will not work for x1e80100 as the master ports are
are not mapped in the same order.
Without this fix only one speaker in a pair of speakers will function.
After this fix along with WSA codec changes both the speakers starts
working.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240626-port-map-v2-5-6cc1c5608cdd@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Soundwire controllers (WSA, WSA2, RX, TX) require reset lines to enable
switching clock control from hardware to software.
Add them along with the reset control providers.
Without this reset we might hit fifo under/over run when we try to write to
soundwire device registers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240624-x1e-swr-reset-v2-3-8bc677fcfa64@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm SM8650 SoC has three CCI controllers with two I2C busses
connected to each of them.
The CCI controllers on SM8650 are compatible with the ones found on
many other older generations of Qualcomm SoCs.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240612215835.1149199-5-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm SM8550 SoC contains 3 Camera Control Interface controllers
very similar to the ones found on other Qualcomm SoCs.
One noticeable difference is that cci@ac16000 controller provides only
one I2C bus and has an additional control over AON CCI pins gpio208
and gpio209, but this feature is not yet supported in the CCI driver.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20240612215835.1149199-4-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
No input events are generated from the pressing of the power key on
either Primus or Flex 5G, because the device node isn't enabled.
Give the power key node a label and enable this for the two devices.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Link: https://lore.kernel.org/r/20240812-sc8180x-pwrkey-enable-v1-1-2bcc22133774@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Change the HW model in sm8650-qrd.dts to a one closer to reality - where
the WLAN and Bluetooth modules of the WCN7850 are powered by the PMU
inside the package.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240709-hci_qca_refactor-v3-6-5f48ca001fed@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The "capacity-dmips-mhz" and "dynamic-power-coefficient" are
used to build Energy Model which in turn is used by EAS to take
placement decisions.
Signed-off-by: Ankit Sharma <quic_anshar@quicinc.com>
Link: https://lore.kernel.org/r/20240731111951.6999-1-quic_anshar@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add pm8950 resin node as a feature of the PMIC it should be declared
in pm8950.dtsi, disabled by default. Like all other optional components
it can then by enabled and configured in the board-specific device tree
part.
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20240730-pm8950_resin-v1-1-26de4d933f95@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Lenovo Flex 5G has a camera attached to the multiport USB
controller, enable the controller and the four phys to enable this.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240730-sc8180x-usb-mp-v2-7-a7dc4265b553@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SC8180X Primus comes with an AUX card with two USB ports, fed by the
two multiport ports.
Enable the involved nodes and define two always-on regulators to enable
VBUS for these ports.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240730-sc8180x-usb-mp-v2-6-a7dc4265b553@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SC8180X platform comes with a multiport DWC3 controller with two
ports, each connected to a pair of HighSpeed and QMP SuperSpeed PHYs.
Describe these blocks.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240730-sc8180x-usb-mp-v2-5-a7dc4265b553@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the pwr_event interrupt and rearrange the order of the other
interrupts to match the binding.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240730-sc8180x-usb-mp-v2-4-a7dc4265b553@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SC8180X comes with two PMC8180 PMICs, with the GPIO block being used
to control VBUS supply of the second USB multiport port.
Rename the GPIO controller in the first PMC8180 to match the schematics
and define this second controller.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240730-sc8180x-usb-mp-v2-3-a7dc4265b553@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
