Add support for using with both wl12xx and wl18xx.
- all wilink family needs special init command for entering wspi mode.
extra clock cycles should be sent after the spi init command while the
cs pin is high.
- Use inverted chip select for sending a dummy 4 bytes command that
completes the init stage.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds the Hisilicon Fast Ethernet MAC(FEMAC) driver.
The FEMAC supports max speed 100Mbps and has been used in many
Hisilicon SoC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Hisilicon Fast Ethernet MAC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB, core driver and binding document to support the
BCM585xx/586xx/88312 integrated switch (Northstar Plus SoCs family).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for TSE PCS that uses SGMII adapter when the phy-mode of
the dwmac is set to sgmii.
Signed-off-by: Tien Hock Loh <thloh@altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a spelling typo in keystone-netcp.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce "ti,cpsw-mdio" compatible string for Davinci MDIO, because
it's required to distinguish the case when MDIO is part of TI CPSW to
enable features supported by TI CPSW (for example, enable PM
management).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document missed "ti,am4372-mdio" compat string used for TI am437x SoC
(am4372.dtsi).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJXa6rGAAoJED07qiWsqSVqzwsH/0g/blikQuNNAB7LzXGTEMn8
ipWCODaYxgWE/V/1A0JjsKpxB1ZL3HE0/xg/OmZ10SRNlz5LJTLkoYZa7xYmyxtT
a89mT9vdnWxwfwbeIhSSjG9W9g44vqrhMIPxffIu5yqSqdIJak0HIiuQizJ0/xjx
xQVx4AykWKQ3u0/Tiyz3ez5yhyMMNEmHxKyDWpgrR6+zXlofwP/Em3NFPwk9gh32
ECAagOUOEvdjXeRs1Yn/CV0FC7Wgs4Hzr048JJ5wOteawBLr+sPOnuWZtDhNrwDK
Eceh7aEeAiFfIW+jCMEe5qrpFHi8hqyqBo4L9TDYsE7T/Z6BPyh+5OUh8+5dtaw=
=TZew
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.8-20160623' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-06-17
this is a pull request of 4 patches for net-next/master.
Arnd Bergmann's patch fixes a regresseion in af_can introduced in
linux-can-next-for-4.8-20160617. There are two patches by Ramesh
Shanmugasundaram, which add CAN-2.0 support to the rcar_canfd driver.
And a patch by Ed Spiridonov that adds better error diagnoses messages
to the Ed Spiridonov driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The controller can operate in one of the two global modes
- CAN FD only mode (default)
- Classical CAN (CAN2.0) only mode
This patch adds support for Classical CAN only mode. It can be enabled
by defining the optional device tree property "renesas,no-can-fd" of this
node.
Note: R-Car Gen3 h/w manual v0.51E shows bit6 of RSCFDnCFDGCFG as
reserved, which is incorrect. This bit is same as RSCFDnGCFG.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJXZAIqAAoJED07qiWsqSVqW0YH/RMgC6CDlJUtHr7+B8YLpi0e
BZOzAHH7mQdP+Z2kIXZp8Dnziq5G8heWNjRwTMPLHvOel+oms+0ZK6VY/kJYArdb
ViGGgi/gQ334JGqJYi2utkyIIIRH7ZxwcblF1aaaFVfFy7tZMVuppIWVzR/V0Gje
/5FftT1f04/6iumEq4es+Jb0OC9azoebSs1DUZTIvYOz3XrnCbB1FdmDN+a3xZKC
Qyav6QVnp/m2InzGSN+Kd/W++EP6YckdBp/++2hizsOvSIOfe8GRqkc0r7fLbfZ8
rucDJNi+GrLat4wNza4t3FKf3rBenBFzii14OEUTE0JgpY90fGUF3n/i0duaB/k=
=90Ns
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.8-20160617' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-06-17
this is a pull request of 14 patches for net-next/master.
Geert Uytterhoeven contributes a patch that adds a file patterns for
CAN device tree bindings to MAINTAINERS. A patch by Alexander Aring
fixes warnings when building without proc support. A patch by me
improves the sample point calculation. Marek Vasut's patch converts
the slcan driver to use CAN_MTU. A patch by William Breathitt Gray
converts the tscan1 driver to use module_isa_driver.
Two patches by Maximilian Schneider for the gs_usb driver fix coding
style and add support for set_phys_id callback. 5 patches by Oliver
Hartkopp add support for CANFD to the bcm. And finally two patches
by Ramesh Shanmugasundaram, which add support for the rcar_canfd
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to hold s/w dependent parameter in device tree.
Even more, there is no reason in this parameter because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels
anyway.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the CAN FD controller found in Renesas R-Car
SoCs. The controller operates in CAN FD only mode by default.
CAN FD mode supports both Classical CAN & CAN FD frame formats. The
controller supports ISO 11898-1:2015 CAN FD format only.
This controller supports two channels and the driver can enable either
or both of the channels.
Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one
per channel) for transmission. Rx filter rules are configured to the
minimum (one per channel) and it accepts Standard, Extended, Data &
Remote Frame combinations.
Note: There are few documentation errors in R-Car Gen3 Hardware User
Manual v0.5E with respect to CAN FD controller. They are listed below:
1. CAN FD interrupt numbers 29 & 30 are listed as per channel
interrupts. However, they are common to both channels (i.e.) they are
global and channel interrupts respectively.
2. CANFD clock is derived from PLL1. This is not documented.
3. CANFD clock is further divided by (1/2) within the CAN FD controller.
This is not documented.
4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It
is specified 4 Tq in the manual.
5. The maximum number of message RAM area the controller can use is 3584
bytes. It is specified 10752 bytes in the manual.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add device tree binding documentation details for Cirrus Logic
CS8900/CS8920 ethernet chip.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c fixes from Wolfram Sang:
- a bigger fix for i801 to finally be able to be loaded on some
machines again
- smaller driver fixes
- documentation update because of a renamed file
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mux: reg: Provide of_match_table
i2c: mux: refer to i2c-mux.txt
i2c: octeon: Avoid printk after too long SMBUS message
i2c: octeon: Missing AAK flag in case of I2C_M_RECV_LEN
i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR
- Fix unflatten_dt_nodes when dad parameter is set.
- Add vendor prefixes for TechNexion and UniWest
- Documentation fix for Marvell BT
- OF IRQ kerneldoc fixes
- Restrict CMA alignment adjustments to non dma-coherent
- Couple of warning fixes in reserved-memory code
- DT maintainers updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rXx9
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix unflatten_dt_nodes when dad parameter is set.
- add vendor prefixes for TechNexion and UniWest
- documentation fix for Marvell BT
- OF IRQ kerneldoc fixes
- restrict CMA alignment adjustments to non dma-coherent
- a couple of warning fixes in reserved-memory code
- DT maintainers updates
* tag 'devicetree-fixes-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
drivers: of: add definition of early_init_dt_alloc_reserved_memory_arch
drivers/of: Fix depth for sub-tree blob in unflatten_dt_nodes()
drivers: of: Fix of_pci.h header guard
dt-bindings: Add vendor prefix for TechNexion
of: add vendor prefix for UniWest
dt: bindings: fix documentation for MARVELL's bt-sd8xxx wireless device
of: add missing const for of_parse_phandle_with_args() in !CONFIG_OF
of: silence warnings due to max() usage
drivers: of: of_reserved_mem: fixup the CMA alignment not to affect dma-coherent
of: irq: fix of_irq_get[_byname]() kernel-doc
MAINTAINERS: DeviceTree maintainer updates
Binding doc for NS2 PCIe PHYs.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT binding doc for Broadcom MDIO bus multiplexer driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "mdio-parent-bus" from mandatory section to optional
as it won't be required by integrated MDIO multiplexer
which has bus selection and mdio transaction generation logic,
integrated inside.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct references to i2c-mux.txt which was previously mux.txt.
Also correct the spelling of relevant.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Document the compatible for INA231 sensor.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the new binding to the documentation of the existing binding.
Mark the old binding as deprecated.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
United Western Technologies Corp, known primarily as UniWest,
is a manufacturer of eddy current and ultrasonic testing equipment.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The property marvell,wakeup-pin and marvell,wakeup-gap-ms are read as
u16 in the driver. Fix documentation and example accordingly.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Document the ddc-i2c-bus property used by imx-ldb driver to read EDID
information via I2C interface.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new
drivers. Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uNKQ
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new drivers.
Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support"
* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: hda - Fix headset mic detection problem for one Dell machine
spi: spi-ep93xx: Fix the PTR_ERR() argument
ALSA: hda/realtek - Add support for ALC295/ALC3254
ASoC: kirkwood: fix build failure
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ASoC: ak4642: Enable cache usage to fix crashes on resume
ASoC: twl6040: Disconnect AUX output pads on digital mute
ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
rcar: src: skip disabled-SRC nodes
ASoC: max98371 Remove duplicate entry in max98371_reg
ASoC: twl6040: Select LPPLL during standby
ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
ASoC: simple-card: Add pm callbacks to platform driver
ASoC: pxa: Fix module autoload for platform drivers
ASoC: topology: Fix memory leak in widget creation
ASoC: Add max98371 codec driver
ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
ASoC: topology: Check size mismatch of ABI objects before parsing
ASoC: topology: Check failure to create a widget
ASoC: add support for TAS5720 digital amplifier
...
Here is the quote from [1]:
The unit-address must match the first address specified
in the reg property of the node. If the node has no reg property,
the @ and unit-address must be omitted and the node-name alone
differentiates the node from other nodes at the same level
This patch adjusts MIPS dts-files and devicetree binding
documentation in accordance with [1].
[1] Power.org(tm) Standard for Embedded Power Architecture(tm)
Platform Requirements (ePAPR). Version 1.1 – 08 April 2011.
Chapter 2.2.1.1 Node Name Requirements
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13345/
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We've already noticed a few flaws in the MTD work for v4.7-rc1:
* The Atmel folks got ahead of themselves on trying to support their latest
hardware and were working off incorrect documentation. Fix up the NAND
driver to get this correct.
* Fix up device tree example documentation to use the latest recommendations
for describing NAND ECC algorithms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kb+w
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160527' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"We've already noticed a few flaws in the MTD work for v4.7-rc1:
- The Atmel folks got ahead of themselves on trying to support their
latest hardware and were working off incorrect documentation. Fix
up the NAND driver to get this correct.
- Fix up device tree example documentation to use the latest
recommendations for describing NAND ECC algorithms"
* tag 'for-linus-20160527' of git://git.infradead.org/linux-mtd:
Documentation: dt: mtd: drop "soft_bch" from example
Revert "mtd: atmel_nand: Support variable RB_EDGE interrupts"
Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
This reverts commit 5ddc7bd43c ("mtd: atmel_nand: Support variable
RB_EDGE interrupts")
Because for current SoCs, the RB_EDGE3(i.e. bit 27) of HSMC_SR
register does not exist, the RB_EDGE0 (i.e. bit 24) is the ready/busy
line edge status bit. It is a datasheet bug.
Cc: <stable@vger.kernel.org>
Fixes: commit 5ddc7bd43c ("mtd: atmel_nand: Support variable RB_EDGE interrupts")
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXOao7AAoJECTWi3JdVIfQ3EQH/1Z4nukvcOeZgVN/4K9b27t2
LYSyPH4+7XiDsi24UAyxZWls625t+1XRtolS0yHYY+IMObkeH/T+StTirDG4C1Mv
0uw/lEs5XmkSPFMad2fDcVXhf+D6EsvuLZ24qLKhoi8TyePv6GRvYapitE4dAI7Z
bBwjT+f9r1qSMJvfCmqit8zDneDFMKd7oqPmBW6NpFri5/ksn1KUnd/zOGu2SlSd
R01Oa2VbRDGj8/Zzu5MORvgLLucxTqtAFYeF3T52M5oc33IBWvbha4fk/BDOswbz
H9S3vHyakmbZgXnnGMTp4qz0bxA76YaHzjtqgGUEMbigHTsB0PP5TtII3i5LkaY=
=Zsr1
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.7' into asoc-linus
ASoC: Updates for v4.7
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
# gpg: Signature made Mon 16 May 2016 12:08:43 BST using RSA key ID 5D5487D0
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
