The 9p-virtio transport does zero copy on things larger than 1024 bytes
in size. It accomplishes this by returning the physical addresses of
pages to the virtio-pci device. At present, the translation is usually a
bit shift.
That approach produces an invalid page address when we read/write to
vmalloc buffers, such as those used for Linux kernel modules. Any
attempt to load a Linux kernel module from 9p-virtio produces the
following stack.
[<ffffffff814878ce>] p9_virtio_zc_request+0x45e/0x510
[<ffffffff814814ed>] p9_client_zc_rpc.constprop.16+0xfd/0x4f0
[<ffffffff814839dd>] p9_client_read+0x15d/0x240
[<ffffffff811c8440>] v9fs_fid_readn+0x50/0xa0
[<ffffffff811c84a0>] v9fs_file_readn+0x10/0x20
[<ffffffff811c84e7>] v9fs_file_read+0x37/0x70
[<ffffffff8114e3fb>] vfs_read+0x9b/0x160
[<ffffffff81153571>] kernel_read+0x41/0x60
[<ffffffff810c83ab>] copy_module_from_fd.isra.34+0xfb/0x180
Subsequently, QEMU will die printing:
qemu-system-x86_64: virtio: trying to map MMIO memory
This patch enables 9p-virtio to correctly handle this case. This not
only enables us to load Linux kernel modules off virtfs, but also
enables ZFS file-based vdevs on virtfs to be used without killing QEMU.
Special thanks to both Avi Kivity and Alexander Graf for their
interpretation of QEMU backtraces. Without their guidence, tracking down
this bug would have taken much longer. Also, special thanks to Linus
Torvalds for his insightful explanation of why this should use
is_vmalloc_addr() instead of is_vmalloc_or_module_addr():
https://lkml.org/lkml/2014/2/8/272
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few releases back a patch made virtio the default transport, however
it was done in a way which side-stepped the mechanism put in place to
allow for this selection. This patch cleans that up while maintaining
virtio as the default transport.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This lets the transport do endian conversion if necessary, and insulates
the drivers from the difference.
Most drivers can use the simple helpers virtio_cread() and virtio_cwrite().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This driver adds an attribute to the existing virtio device so a CHANGE
event is required in order udev rules to make use of it. The ADD event
happens before this driver is probed and unlike a more typical driver
like a block device there isn't a higher level device to watch for.
Signed-off-by: Michael Marineau <michael.marineau@coreos.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
I dived into lguest again, reworking the pagetable code so we can move
the switcher page: our fixmaps sometimes take more than 2MB now...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1tYL
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio & lguest updates from Rusty Russell:
"Lots of virtio work which wasn't quite ready for last merge window.
Plus I dived into lguest again, reworking the pagetable code so we can
move the switcher page: our fixmaps sometimes take more than 2MB now..."
Ugh. Annoying conflicts with the tcm_vhost -> vhost_scsi rename.
Hopefully correctly resolved.
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (57 commits)
caif_virtio: Remove bouncing email addresses
lguest: improve code readability in lg_cpu_start.
virtio-net: fill only rx queues which are being used
lguest: map Switcher below fixmap.
lguest: cache last cpu we ran on.
lguest: map Switcher text whenever we allocate a new pagetable.
lguest: don't share Switcher PTE pages between guests.
lguest: expost switcher_pages array (as lg_switcher_pages).
lguest: extract shadow PTE walking / allocating.
lguest: make check_gpte et. al return bool.
lguest: assume Switcher text is a single page.
lguest: rename switcher_page to switcher_pages.
lguest: remove RESERVE_MEM constant.
lguest: check vaddr not pgd for Switcher protection.
lguest: prepare to make SWITCHER_ADDR a variable.
virtio: console: replace EMFILE with EBUSY for already-open port
virtio-scsi: reset virtqueue affinity when doing cpu hotplug
virtio-scsi: introduce multiqueue support
virtio-scsi: push vq lock/unlock into virtscsi_vq_done
virtio-scsi: pass struct virtio_scsi to virtqueue completion function
...
virtio_add_buf() is going away, replaced with virtio_add_sgs() which
takes multiple terminated scatterlists.
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Commit b67bfe0d42 ("hlist: drop the node parameter from iterators")
did a lot of nice changes but also contains two small hunks that seem to
have slipped in accidentally and have no apparent connection to the
intent of the patch.
This reverts the two extraneous changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This member of struct virtio_chan is calculated from nr_free_buffer_pages
so change its type to unsigned long in case of overflow.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using a virtio transport, the 9p net device may pass the physical
address of a kernel buffer to userspace via a scatterlist inside a
virtqueue. If the kernel buffer is mapped outside of the linear mapping
(e.g. highmem), then virt_to_page will return a bogus value and we will
populate the scatterlist with junk.
This patch uses kmap_to_page when populating the page array for a kernel
buffer.
Cc: stable@kernel.org
Cc: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BUG_ON() in pack_sg_list() would get triggered only one time after we've
corrupted some memory by sg_set_buf() into an invalid sg buffer.
I'm still working on figuring out why I manage to trigger that bug...
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Remove wrapper functions. This makes the allocation type explicit in
all callers; I used GPF_KERNEL where it seemed obvious, left it at
GFP_ATOMIC otherwise.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reduce object size by deduplicating formats.
Use vsprintf extension %pV.
Rename P9_DPRINTK uses to p9_debug, align arguments.
Add function for _p9_debug and macro to add __func__.
Add missing "\n"s to p9_debug uses.
Remove embedded function names as p9_debug adds it.
Remove P9_EPRINTK macro and convert use to pr_<level>.
Add and use pr_fmt and pr_<level>.
$ size fs/9p/built-in.o*
text data bss dec hex filename
62133 984 16000 79117 1350d fs/9p/built-in.o.new
67342 984 16928 85254 14d06 fs/9p/built-in.o.old
$ size net/9p/built-in.o*
text data bss dec hex filename
88792 4148 22024 114964 1c114 net/9p/built-in.o.new
94072 4148 23232 121452 1da6c net/9p/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
* remove lot of update to different data structure
* add a seperate callback for zero copy request.
* above makes non zero copy code path simpler
* remove conditionalizing TREAD/TREADDIR/TWRITE in the zero copy path
* Fix the dotu p9_check_errors with zero copy. Add sufficient doc around
* Add support for both in and output buffers in zero copy callback
* pin and unpin pages in the same context
* use helpers instead of defining page offset and rest of page ourself
* Fix mem leak in p9_check_errors
* Remove 'E' and 'F' in p9pdu_vwritef
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
With msize equal to 512K (PAGE_SIZE * VIRTQUEUE_NUM), we hit multiple
crashes. This patch fix those.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Recent zerocopy work in the 9P VirtIO transport maps and pins
user buffers into kernel memory for the server to work on them.
Since the user process can initiate this kind of pinning with a simple
read/write call, thousands of IO threads initiated by the user process can
hog the system resources and could result into denial of service.
This patch introduces flow control to avoid that extreme scenario.
The ceiling limit to avoid denial of service attacks is set to relatively
high (nr_free_pagecache_pages()/4) so that it won't interfere with
regular usage, but can step in extreme cases to limit the total system
hang. Since we don't have a global structure to accommodate this variable,
I choose the virtio_chan as the home for this.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Reviewed-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Given that the sprious wake-ups are common, we need to move the
condition setting right next to the wake_up(). After setting the condition
to req->status = REQ_STATUS_RCVD, sprious wakeups may cause the
virtqueue back on the free list for someone else to use.
This may result in kernel panic while relasing the pinned pages
in p9_release_req_pages().
Also rearranged the while loop in req_done() for better redability.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Process may wait to get space on VirtIO ring to send a transaction to
VirtFS server. Current code just does a conditional wake_up() which
means only one process will be woken up even if multiple processes
are waiting.
This fix makes the wake_up unconditional. Hence we won't have any
processes waiting for-ever.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch adds preferences field to the p9_trans_module.
Through this, now transport layer can express its preference about the
payload. i.e if payload neds to be part of the PDU or it prefers it
to be sent sepearetly so that the transport layer can handle it in
a better way.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Modify p9_virtio_request() and req_done() functions to support
additional payload sent down to the transport layer through
tc->pubuf and tc->pkbuf.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
If there is not enough space for the PDU on the VirtIO ring, current
code returns -EIO propagating the error to user.
This patch introduced a wqit_queue on the channel, and lets the process
wait on this queue until VirtIO ring frees up.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
p9_virtio_create will only compare the the channel's tag characters
against the device name till the end of the channel's tag but not till
the end of the device name. This means that if a user defines channels
with the tags foo and foobar then he would mount foo when he requested
foonot and may mount foo when he requested foobar.
Thus it is necessary to check both string lengths against each other in
case of a successful partial string match.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch trans_virtio to new virtqueue_xxx wrappers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This adds a new file for virtio 9P device. The file
contain details of the mount device name that should
be used to mount the 9P file system.
Ex: /sys/devices/virtio-pci/virtio1/mount_tag file now
contian the tag name to be used to mount the 9P file system.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch use the tag name in the config space to identify the
mount device. The the virtio device name depend on the enumeration
order of the device and may not remain the same across multiple boots
So we use the tag name which is set via qemu option to uniquely identify
the mount device
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
With this patch we have
# mount -t 9p -o trans=virtio virtio2 /mnt/
# mount -t 9p -o trans=virtio virtio2 /mnt/
mount: virtio2 already mounted or /mnt/ busy
mount: according to mtab, virtio2 is already mounted on /mnt
# mount -t 9p -o trans=virtio virtio3 /mnt/ -o debug=0xfff
mount: special device virtio3 does not exist
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Use a list to track the channel instead of statically
allocated array
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This is needed for supporting multiple mount points.
We can find out the device names to be used with mount by checking
/sys/devices/virtio-pci/virtio*/device file
if the device file have value 9 then the specific virtio device can
be used for mounting.
ex:
#cat /sys/devices/virtio-pci/virtio1/device
9
now we can mount using
# mount -t 9p -o trans=virtio virtio1 /mnt/
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The 9p virtio transport was not updating its connection status correctly
preventing it from being able to mount the server.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Rusty,
commit 3ca4f5ca73
virtio: add virtio IDs file
moved all device IDs into a single file. While the change itself is
a very good one, it can break userspace applications. For example
if a userspace tool wanted to get the ID of virtio_net it used to
include virtio_net.h. This does no longer work, since virtio_net.h
does not include virtio_ids.h.
This patch moves all "#include <linux/virtio_ids.h>" from the C
files into the header files, making the header files compatible with
the old ones.
In addition, this patch exports virtio_ids.h to userspace.
CC: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Virtio IDs are spread all over the tree which makes assigning new IDs
bothersome. Putting them together should make the process less error-prone.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
VIRTIO_ID_9P is already defined in include/linux/virtio_9p.h
so use that definition instead.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
This API change means that virtio_net can tell how much capacity
remains for buffers. It's necessarily fuzzy, since
VIRTIO_RING_F_INDIRECT_DESC means we can fit any number of descriptors
in one, *if* we can kmalloc.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dinesh Subhraveti <dineshs@us.ibm.com>
Fix the comments -- mostly the improper and/or missing descriptions
of function parameters.
Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This replaces find_vq/del_vq with find_vqs/del_vqs virtio operations,
and updates all drivers. This is needed for MSI support, because MSI
needs to know the total number of vectors upfront.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ lguest/9p compile fixes)
Add a linked list of all virtqueues for a virtio device: this helps for
debugging and is also needed for upcoming interface change.
Also, add a "name" field for clearer debug messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently the 9p code crashes when a operation is interrupted, i.e. for
example when the user presses ^C while reading from a file.
This patch fixes the code that is responsible for interruption and flushing
of 9P operations.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
This code moves the rpc function to the common client base,
reorganizes the flush code to be more simple and stable, and
makes the necessary adjustments to the underlying transports
to adapt to the new structure.
This reduces the overall amount of code duplication between the
transports and should make adding new transports more straightforward.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The virtio transport uses a simplified request management system
that I want to use for all transports. This patch adapts and moves the
exisiting code for managing requests to the client common code.
Later patches will apply these mechanisms to the other transports.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Right now there is a transport module structure which provides per-transport
type functions and data and a transport structure which contains per-instance
public data as well as function pointers to instance specific functions.
This patch moves public transport visible instance data to the client
structure (which in some cases had duplicate data) and consolidates the
functions into the transport module structure.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
9p trans modules aren't refcounted nor were they unregistered
properly. Fix it.
* Add 9p_trans_module->owner and reference the module on each trans
instance creation and put it on destruction.
* Protect v9fs_trans_list with a spinlock. This isn't strictly
necessary as the list is manipulated only during module loading /
unloading but it's a good idea to make the API safe.
* Unregister trans modules when the corresponding module is being
unloaded.
* While at it, kill unnecessary EXPORT_SYMBOL on p9_trans_fd_init().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Some files in the net/9p directory uses "int" for flags. This can
cause hard to find bugs on some architectures. This patch converts the
flags to use "long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel
where checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
Replace semaphores protecting use flags with a mutex.
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
The kernel-doc comments of much of the 9p system have been in disarray since
reorganization. This patch fixes those problems, adds additional documentation
and a template book which collects the 9p information.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The Coverity checker spotted that less memory than required was
allocated.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
if (...) BUG(); should be replaced with BUG_ON(...) when the test has no
side-effects to allow a definition of BUG_ON that drops the code completely.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ disable unlikely @ expression E,f; @@
(
if (<... f(...) ...>) { BUG(); }
|
- if (unlikely(E)) { BUG(); }
+ BUG_ON(E);
)
@@ expression E,f; @@
(
if (<... f(...) ...>) { BUG(); }
|
- if (E) { BUG(); }
+ BUG_ON(E);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This merges the mux.c (including the connection interface) with trans_fd
in preparation for transport API changes. Ultimately, trans_fd will need
to be rewritten to clean it up and simplify the implementation, but this
reorganization is viewed as the first step.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Request from rusty:
Just cleaning up patches for 2.6.25 merge, and noticed that
net/9p/trans_virtio.c doesn't have a remove function. This will crash when
removing the module (console doesn't have one because it can't really be
removed).
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This replaces the console-based virto client with a block-based
client using a single request queue.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
It seems that virtio_net wants to disable callbacks (interrupts) before
calling netif_rx_schedule(), so we can't use the return value to do so.
Rename "restart" to "cb_enable" and introduce "cb_disable" hook: callback
now returns void, rather than a boolean.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Previously we used a type/len pair within the config space, but this
seems overkill. We now simply define a structure which represents the
layout in the config space: the config space can now only be extended
at the end.
The main driver-visible changes:
1) We indicate what fields are present with an explicit feature bit.
2) Virtqueues are explicitly numbered, and not in the config space.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This adds a transport to 9p for communicating between guests and a host
using a virtio based transport.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
