If during validation of the firmware download the data doesn't match what is
expected out of the chip, this calls for a firmware download failure and a
retry.
Free the SKB which collects response during such scenarios.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.
So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.
In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.
Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
devres_release_all and devres_release_group both aquire the lock
&dev->devres_lock but the release of that lock is done in release_nodes.
This results in sparse noise about context imbalance.
Add a lock annotation to release_nodes to quiet this noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
allmodconfig compile fails on s390 because of the new PTI driver:
drivers/misc/pti.c:407:3: error: implicit declaration of function 'pci_iounmap'
drivers/misc/pti.c:410:3: error: implicit declaration of function 'pci_release_region'
Add a 'depends on PCI' statement so it doesn't get compiled.
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace unnecessary if with else statement.
This fixes the following (false) compile warning reported with some combinations
of C compiler version and configuration.
drivers/hwmon/ntc_thermistor.c: In function 'ntc_show_temp':
drivers/hwmon/ntc_thermistor.c:225: warning: 'low' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'low' was declared here
drivers/hwmon/ntc_thermistor.c:225: warning: 'high' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'high' was declared here
drivers/hwmon/ntc_thermistor.c:294: warning: 'temp' may be used uninitialized in
this function
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Currently the Option driver avoids binding interface 1 on Huawei K3765
and K4505 broadband modems as it should be handled by the cdc_ether
driver instead. This patch ensures we don't bind the interface 2
on those devices as that is CDC_DATA.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a NULL pointer deference. A NULL pointer
dereference happens since s5p_ehci->hcd field is not initialized
yet in probe function.
[jg1.han@samsung.com: edit commit message]
Signed-off-by: Yulgon Kim <yulgon.kim@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears
PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host
Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME
bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss
the action of clearing PORT_RESUME. This will cause unexpected long
resume signal on USB bus.
Signed-off-by: Wang Zhi <zhi.wang@windriver.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K4605 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by suitable network
driver.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K3806 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
xhci: Remove TDs from TD lists when URBs are canceled.
xhci: Fix failed enqueue in the middle of isoch TD.
xhci: Fix memory leak during failed enqueue.
xHCI: report USB2 port in resuming as suspend
xHCI: fix port U3 status check condition
With qla2xxx, acl_node_lock is taken inside qla2xxx's hardware_lock,
which is taken in hardirq context. This means acl_node_lock must become
an IRQ-disabling lock; in particular this fixes lockdep warnings along
the lines of
======================================================
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
(&(&se_tpg->acl_node_lock)->rlock){+.....}, at: [<ffffffffa026f872>] transport_deregister_session+0x92/0x140 [target_core_mod]
and this task is already holding:
(&(&ha->hardware_lock)->rlock){-.-...}, at: [<ffffffffa017c5e7>] qla_tgt_stop_phase1+0x57/0x2c0 [qla2xxx]
which would create a new lock dependency:
(&(&ha->hardware_lock)->rlock){-.-...} -> (&(&se_tpg->acl_node_lock)->rlock){+.....}
but this new dependency connects a HARDIRQ-irq-safe lock:
(&(&ha->hardware_lock)->rlock){-.-...}
to a HARDIRQ-irq-unsafe lock:
(&(&se_tpg->acl_node_lock)->rlock){+.....}
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
At least the tcm_qla2xxx fabric driver calls into transport_deregister_session()
while holding an IRQ-disabled spinlock, so the inner locking needs to
use spin_lock_irqsave() instead of spin_lock_bh().
This fixes warnings seen with tcm_qla2xxx like:
WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x98/0xb0()
Call Trace:
[<ffffffff8104e65f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8104e6ba>] warn_slowpath_null+0x1a/0x20
[<ffffffff81055368>] local_bh_enable_ip+0x98/0xb0
[<ffffffff814d5284>] _raw_spin_unlock_bh+0x14/0x20
[<ffffffffa027b7f6>] transport_deregister_session+0x96/0x180 [target_core_mod]
[<ffffffffa00f7731>] tcm_qla2xxx_free_session+0xd1/0x170 [tcm_qla2xxx]
[<ffffffffa01b9173>] qla_tgt_sess_put+0xc3/0x140 [qla2xxx]
[<ffffffffa01bf40f>] qla_tgt_stop_phase1+0x8f/0x2c0 [qla2xxx]
[<ffffffffa00f735e>] tcm_qla2xxx_tpg_store_enable+0x6e/0xd0 [tcm_qla2xxx]
[<ffffffffa026ca29>] target_fabric_tpg_attr_store+0x39/0x40 [target_core_mod]
[<ffffffffa00a575d>] configfs_write_file+0xbd/0x120 [configfs]
[<ffffffff811464a6>] vfs_write+0xc6/0x180
[<ffffffff811467c1>] sys_write+0x51/0x90
[<ffffffff814dd382>] system_call_fastpath+0x16/0x1b
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There's no need for the #ifdef protection when building into the kernel,
and in fact we need the module_init() for the initialization function to
be called.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make a log message more useful by printing both the page and subpage
that an initiator is requesting.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes two bugs in allocation failure handling in
iscsit_allocate_se_cmd_for_tmr():
This first reported by DanC is a free-after call to transport_free_se_cmd(), this
patch drops the transport_free_se_cmd() call all together, as iscsit_release_cmd()
will release existing allocations as expected.
The second is a bug where iscsi_cmd_t was being leaked on a cmd->tmr_req allocation
failure, so make this jump to iscsit_release_cmd() as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The iSCSI target configfs code to print out an initiator's IPv6 address
is not fully implemented. This patch uses snprintf() with the "%pI6c"
format string to format the IPv6 address for display purposes.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes two bugs associated with transport_do_task_sg_chain()
operation where transport_allocate_data_tasks() was incorrectly setting
task_padded_sg for all tasks, and causing bogus task->task_sg_nents
assignments + OOPsen with fabrics depending upon this code. The first bit
here adds a task_sg_nents_padded check in transport_allocate_data_tasks()
to include an extra SGL vector when necessary for tasks that expect to
be linked using sg_chain().
The second change involves making transport_do_task_sg_chain() properly
account for the extra SGL vector when task->task_padded_sg is set for
the non trailing ->task_sg or single ->task_sg allocations. Note this
patch also removes the BUG_ON(!task->task_padded_sg) check within
transport_do_task_sg_chain() as we expect this to happen normally
with the updated logic in transport_allocate_data_tasks(), along with
being bogus for CONTROL_SG_IO_CDB type payloads.
So far this bugfix has been tested with tcm_qla2xxx and iblock backends
in (task_count > 1)( and (task_count == 1) operation.
Reported-by: Kiran Patil <kiran.patil@intel.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses recent breakage with multiple se_task (task_count > 1)
operation following backend dev->se_sub_dev->se_dev_attrib.max_sectors in new
transport_allocate_data_tasks() code. The initial bug here was a bogus
task->task_sg_nents assignment in transport_allocate_data_tasks() based on
the passed parameter, which now uses DIV_ROUND_UP(task_size, PAGE_SIZE) to
determine the proper number of per task SGL entries for the (task_count > 1)
case.
This also means we now need to enforce a PAGE_SIZE aligned max_sector count
value for this to work as expected without bringing back the pre v3.1
transport_map_mem_to_sg() logic to handle SGL offsets across multiple tasks.
So this patch adds se_dev_align_max_sectors() to round down max_sectors as
necessary to ensure this alignment via se_dev_set_default_attribs() and
se_dev_align_max_sectors() and keeps it simple for (task_count > 1)
operation.
So far this bugfix has been tested with (task_count > 1) operation
using iscsi-target and iblock backends.
Reported-by: Chris Boot <bootc@bootc.net>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing transport_cmd_get_valid_sectors() check for
SCF_SCSI_DATA_SG_IO_CDB type payloads to ensure that a received LBA + range
does not exeed past the end of associated backend struct se_device.
This patch also fixes a bug in the failure path of transport_new_cmd_obj()
where this check can fail, so change to use a signed 'rc' and return '-EINVAL'
to signal proper transport_generic_request_failure() handling.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a SYNCHRONIZE_CACHE CDB handling bug with IBLOCK/FILEIO
backends where transport_cmd_get_valid_sectors() was incorrectly rejecting
a zero LBA + range CDB from being processed, and returning CHECK_CONDITION.
This includes changing transport_cmd_get_valid_sectors() to return '0' on
success and '-EINVAL' on failure (this makes more sense than sectors),
and to only check transport_cmd_get_valid_sectors() when a non zero LBA +
range SYNCHRONIZE_CACHE operation has been receieved for the non passthrough
case.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a duplicate set of transport_complete_task() calls in
target_emulate_unmap() and target_emulate_write_same() as the completion
call is already done within transport_emulate_control_cdb()
This patch also adds a check in transport_emulate_control_cdb() for the
existing SCF_EMULATE_CDB_ASYNC flag currently used by SYNCHRONIZE_CACHE
in order to handle IMMEDIATE processing.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For all flavours of WRITE_SAME, we only expect to handle a single block
of data-out buffer payload, regardless of the number of logical blocks
presented in the CDB. This patch changes all flavours of WRITE_SAME in
transport_generic_cmd_sequencer() to pass '1' into transport_get_size()
instead of the extracted 'sectors' to properly handle the default usage
of sg_write_same without the --xferlen parameter.
Reported-by: Eric Seppanen <eric@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch adds initial WRITE_SAME (10) w/ UNMAP=1 support following updates in
sbcr26 to allow UNMAP=1 for the non 16 + 32 byte CDB case. It also refactors
current pSCSI passthrough passthrough checks into target_check_write_same_discard()
ahead of UNMAP=0 w/ write payload support into target_core_iblock.c.
This includes the support for handling WRITE_SAME in transport_emulate_control_cdb(),
and converts target_emulate_write_same to accept num_blocks directly for
WRITE_SAME, WRITE_SAME_16 and WRITE_SAME_32.
Reported-by: Eric Seppanen <eric@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch fixes a bug for fabrics using tfo->new_cmd_map() that
are expect transport_generic_request_failure() to be calling
transport_send_check_condition_and_sense() for both READ and WRITE,
instead of only for READ exceptions.
This was originally observed with a failed WRITE_SAME_16 w/ unmap=0
using tcm_loop.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a forever loop bug in iscsit_attach_ooo_cmdsn()
while walking sess->sess_ooo_cmdsn_list when the received
CmdSN is less than the tail of the list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use BUG_ON(x) rather than if(x) BUG();
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ identifier x; @@
-if (x) BUG();
+BUG_ON(x);
@@ identifier x; @@
-if (!x) BUG();
+BUG_ON(!x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We leak memory if the allocations for 'new_param->name' or
'new_param->value' fail in iscsi_target_parameters.c::iscsi_copy_param_list()
We also do a lot of variable assignments that are completely pointless
if the allocations fail.
So, let's move the allocations before the assignments and also make
sure that we free whatever was allocated to one if the allocation fail.
There's also some small CodingStyle fixups in there (curly braces on
both branches of if statement, only one variable per line) since I was
in the area anyway. And finally, error messages in the function are
put on a single line for easy grep'abillity.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
The semantic patch that makes this output is available
in scripts/coccinelle/api/err_cast.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target_emulate_inquiry_std() to set the 'not connected'
(0x35) bit in standard INQUIRY response data when we are processing a
request to a virtual LUN=0 mapping from struct se_device *g_lun0_dev that
have been setup for us in transport_lookup_cmd_lun().
This addresses an issue where qla2xxx FC clients need to be able
to create demo-mode I_T FC Nexuses by default, but should not be
exposing the default set of TPG LUNs to all FC clients. This includes
adding an new optional target_core_fabric_ops->tpg_check_demo_mode_login_only()
caller to allow demo_mode nexuses to skip the old default of bulding
a demo-mode MappedLUNs list via core_tpg_add_node_to_devs().
(roland: Add missing tpg_check_demo_mode_login_only check in core_dev_add_lun)
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
The interrupt status registers should be read in row to avoid invalid data.
Alter "read" method for both bus options to allow reading several registers
in a row and make sure we read interrupt status registers properly.
Read sequence saves 50% of bus transactions compared to single register
reads. So use it also for the result registers, which are also located
in a row.
Also update copyright notice.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
spi_write() requires use of DMA-safe (cacheline aligned) buffers.
Also use the same buffers when reading data since to avoid extra
locking and potential memory allocation in spi_write_then_read().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow driver to be used on Big Endian boxes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise these would need to be painstakingly calculated looking at the source
code.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alpha needs to have available the system bus address for the Radeon's
local memory, so that it can be used in ttm_bo_vm_fault(), when building
the PTEs for accessing that VRAM. So, we make bus.addr hold the ioremap()
return, and then we can modify bus.base appropriately for use during page
fault processing.
Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ep93xx_keypad.c uses interfaces from linux/module.h,
so it should include that file. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
tnetv107x-ts.c uses interfaces from linux/module.h,
so it should include that file. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix new kernel-doc warning in pci.c:
Warning(drivers/pci/pci.c:3259): No description found for parameter 'mps'
Warning(drivers/pci/pci.c:3259): Excess function parameter 'rq' description in 'pcie_set_mps'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original license statement was confusing since it was unclear if
the license was pure GPLv2 or GPLv2+ and did not match the license
of the driver max11801_ts was derived from. The license is GPLv2+.
Signed-off-by: Jiejing Zhang <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command. However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL. Since we're not doing that yet, go
back to the old default so things work.
v2: don't forget to actually *clear* the new bit
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.dk/linux-block: (23 commits)
Revert "cfq: Remove special treatment for metadata rqs."
block: fix flush machinery for stacking drivers with differring flush flags
block: improve rq_affinity placement
blktrace: add FLUSH/FUA support
Move some REQ flags to the common bio/request area
allow blk_flush_policy to return REQ_FSEQ_DATA independent of *FLUSH
xen/blkback: Make description more obvious.
cfq-iosched: Add documentation about idling
block: Make rq_affinity = 1 work as expected
block: swim3: fix unterminated of_device_id table
block/genhd.c: remove useless cast in diskstats_show()
drivers/cdrom/cdrom.c: relax check on dvd manufacturer value
drivers/block/drbd/drbd_nl.c: use bitmap_parse instead of __bitmap_parse
bsg-lib: add module.h include
cfq-iosched: Reduce linked group count upon group destruction
blk-throttle: correctly determine sync bio
loop: fix deadlock when sysfs and LOOP_CLR_FD race against each other
loop: add BLK_DEV_LOOP_MIN_COUNT=%i to allow distros 0 pre-allocated loop devices
loop: add management interface for on-demand device allocation
loop: replace linked list of allocated devices with an idr index
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: OF: Don't crash when bridge parent is NULL.
PCI: export pcie_bus_configure_settings symbol
PCI: code and comments cleanup
PCI: make cardbus-bridge resources optional
PCI: make SRIOV resources optional
PCI : ability to relocate assigned pci-resources
PCI: honor child buses add_size in hot plug configuration
PCI: Set PCI-E Max Payload Size on fabric
Add linux/module.h to fix this compilation error:
drivers/power/s3c_adc_battery.c:435:15: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:435:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:435:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_AUTHOR’
drivers/power/s3c_adc_battery.c:435:15: warning: function declaration isn’t a prototype
drivers/power/s3c_adc_battery.c:436:20: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:436:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:436:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_DESCRIPTION’
drivers/power/s3c_adc_battery.c:436:20: warning: function declaration isn’t a prototype
drivers/power/s3c_adc_battery.c:437:16: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:437:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:437:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_LICENSE’
drivers/power/s3c_adc_battery.c:437:16: warning: function declaration isn’t a prototype
make[2]: *** [drivers/power/s3c_adc_battery.o] Error 1
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
power/max8997_charger.c uses interfaces from linux/module.h,
so it should include that file. This fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
power/max8998_charger.c uses interfaces from linux/module.h,
so it should include that file. This fixes build errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
In pcibios_get_phb_of_node(), we will crash while booting if
bus->bridge->parent is NULL.
Check for this case and avoid dereferencing the NULL pointer.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, error handling code in this function calls the function
sata_dwc_port_stop, but this function has essentially no effect if hsdevp
has not been stored in ap, which is the case throughout this function. The
only effect is to print a debugging message including ap->print_id.
The code is rewritten to not call sata_dwc_port_stop, but instead to jump
to a local label that prints the original error message and the print_id
information. In the case where hsdevp has been already allocated (but not
yet stored in ap), this value is freed as well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add basic support for pata on iMX. It has been tested only on imx51.
SDMA support will probably be added later so this version supports only
PIO.
v2:
- enable only when needed IORDY
- use dev_get_drvdata
v3:
- add missing clk_put() calls
- use platform_get_irq()
- fix resume code to avoid disabling IORDY on resume
v4:
- Remove EXPERIMENTAL and switch to depends on ARCH_MXC
- Use devm_kzalloc()
- make clock a must-have
- Use only 1 ioremap
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On AVERATEC 3200, pata_via causes memory corruption with ATAPI DMA,
which often leads to random kernel oops. The cause of the problem is
not well understood yet and only small subset of machines using the
controller seem affected. Blacklist ATAPI DMA on the machine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=11426
Reported-and-tested-by: Jim Bray <jimsantelmo@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Init 'serror' to silence the following warning:
drivers/ata/sata_sil.c: In function ‘sil_interrupt’:
drivers/ata/sata_sil.c:453:14: warning: ‘serror’ may be used uninitialized in
this function [-Wuninitialized]
This is not a 'can never happen' but is nonetheless extremely unlikely.
The easiest and cleanest warning fix is simply to init the var,
rather than worry about marking the var uninit-ok.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Based on a patch from the PaX Team, found during a clang analysis pass.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: stable@kernel.org [v2.6.35+]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If hw does not support vlans, dont call nv_vlan_mode because it has no point.
I believe that this should fix issues on older non-vlan supportive
chips (like Ingo has).
Reported-ty: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's undesired to filter untagged packets at any time. So simply remove this.
Reported-by: Stephan Bärwolf <stephan.baerwolf@tu-ilmenau.de>
Tested-by: Stephan Bärwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eduard Sinelnikov (eduard.sinelnikov@gmail.com) found that if we change
bonding mode from active backup to round robin, some slaves are still keeping
"backup", and won't transmit packets.
As Jay Vosburgh(fubar@us.ibm.com) pointed out that we can work around that by
removing the bond_is_active_slave() check, because the "backup" flag is only
meaningful for active backup mode.
But if we just simply ignore the bond_is_active_slave() check,
the transmission will work fine, but we can't maintain the correct value of
"backup" flag for each slaves, though it is meaningless for other mode than
active backup.
I'd like to reset "backup" and "inactive" flag in bond_open,
thus we can keep the correct value of them.
As for bond_is_active_slave(), I'd like to prepare another patch to handle it.
V2:
Use C style comment.
Move read_lock(&bond->curr_slave_lock).
Replace restore with reset, for active backup mode, it means "restore",
but for other modes, it means "reset".
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rtc: Limit RTC PIE frequency
rtc: Fix hrtimer deadlock
rtc: Handle errors correctly in rtc_irq_set_state()
Fixup trivial conflicts in drivers/rtc/interface.c due to slightly
trivially versions of the same patch coming in two different ways.
RFC3270 mandates that iSCSI PDUs are padded to the closest integer
number of four byte words. Fix the iser code to support that on both
the TX/RX flows.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The code that prepares the SG associated with SCSI command for FMR was
buggy for systems with DMA addresses that don't fit in unsigned long,
e.g under the 32-bit based XenServer dom0 sizeof(dma_addr_t) is 8.
Fix that by casting to unsigned long long a masking constant used by
the code. This resolves a crash in iser_sg_to_page_vec on this system.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Atmel mxt1386 touch controller has the touch pressure information so
let's report it to the user space.
[dtor@mail.ru: added ABS_RESSURE reporting for ST emulation.]
Signed-off-by: Yufeng Shen <miletus@chromium.org>
Acked-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New MacBook Pro devices reporting product name MacBookPro8,2 come with
newer/higher resolution touchpads than others with the same product
name with USB ID 05ac:0252. This patch adds support for these devices.
Signed-off-by: Andrew Drake <adrake@adrake.org>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch changes transport_send_check_condition_and_sense() for
TCM_NON_EXISTENT_LUN emulation to use 0x25 (LOGICAL UNIT NOT SUPPORTED)
instead of the original 0x20 (INVALID COMMAND OPERATION CODE). This is
helpful to distinguish between TCM_UNSUPPORTED_SCSI_OPCODE ASC=0x20
exceptions.
Signed-off-by: Nicholas A. Bellinger <nab@risingtidesystems.com>
For a long time, the xHCI driver has had this note:
/* FIXME: Ignoring zero-length packets, can those happen? */
It turns out that, yes, there are drivers that need to queue zero-length
transfers for isochronous OUT transfers. Without this patch, users will
see kernel hang messages when a driver attempts to enqueue an isochronous
URB with a zero length transfer (because count_isoc_trbs_needed will return
zero for that TD, xhci_td->last_trb will never be set, and updating the
dequeue pointer will cause an infinite loop).
Matěj ran into this issue when using an NI Audio4DJ USB soundcard
with the snd-usb-caiaq driver. See
https://bugzilla.kernel.org/show_bug.cgi?id=40702
Fix count_isoc_trbs_needed() to return 1 for zero-length transfers (thanks
Alan on the math help). Update the various TRB field calculations to deal
with zero-length transfers. We're still transferring one packet with a
zero-length data payload, so the total_packet_count should be 1. The
Transfer Burst Count (TBC) and Transfer Last Burst Packet Count (TLBPC)
fields should be set to zero.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Matěj Laitl <matej@laitl.cz>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
Fix build errors (found when CONFIG_SYSFS is not enabled):
drivers/xen/xen-selfballoon.c:446: warning: data definition has no type or storage class
drivers/xen/xen-selfballoon.c:446: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
drivers/xen/xen-selfballoon.c:446: warning: parameter names (without types) in function declaration
drivers/xen/xen-selfballoon.c:485: error: expected declaration specifiers or '...' before string constant
drivers/xen/xen-selfballoon.c:485: warning: data definition has no type or storage class
drivers/xen/xen-selfballoon.c:485: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/xen/xen-selfballoon.c:485: warning: function declaration isn't a prototype
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill Shutemov found problems with the non-upstream IMG driver where the
use of extra DRM encoder/connector types caused random crashes when the DRM
layer tried to display their matching name. This removes the MIPI types
matching the changes Pauli Nieminen made to the non upstream driver set.
As Pauli points out:
" MIPI (or DSI) is protocol specification on top of LVDS serial bus. That
makes it resonable to call MIPI connectors and encoders LVDS."
(and indeed they may also be HDMI convertors or similar when we want to
report a more useful to end user result)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b33f9cbd67 ("regmap: Specify a module license") added a
MODULES_LICENSE to this file without adding an include of module.h.
module.h should have been included anyway, since this file has
EXPORT_SYMBOLs as well. With the pending module.h split up, this would
probably have caused build problems.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: Cannot set clock gating under UMS
drm/i915: Can't do accurate vblank timestamps with UMS
Not all systems expose a firmware or platform mechanism for changing the backlight intensity on i915, so add native driver support.
drm/i915: split out PCH refclk update code
drm/i915: show interrupt info on IVB
drm/i915: Remove unused 'reg' argument to dp_pipe_enabled
drm/i915: Fix PCH port pipe select in CPT disable paths
drm/i915: Leave LVDS registers unlocked
drm/i915: Wait for LVDS panel power sequence
The clock gating functions are only assigned under KMS, so don't try
to call them under UMS.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Disable this feature when KMS is not running by setting the
driver->get_vblank_timestamp function pointer to NULL.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Tested-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
usb_ifnum_to_if() can return NULL if the USB device does not have a
configuration installed (usb_device->actconfig == NULL), or if we can't
find the interface number in the installed configuration. Return an
error instead of crashing.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: fix DMA unmapping in an error path
firewire: cdev: fix 32 bit userland on 64 bit kernel compat corner cases
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: don't try to be smart in the hpd handler
drm/radeon: re-POST the asic on Apple hardware when booted via EFI
drm/radeon: Allow panel preferred EDID to override BIOS native mode
drm/radeon/kms: make some watermark messages debug only
drm/radeon/kms: fix regression is handling >2 heads on cedar/caicos
drm/radeon/kms: don't enable connectors that are off in the hotplug handler
Attempting to try and turn off disconnected display hw in the
hotput handler lead to more problems than it helped. For
now just register an event and only attempt the do something
interesting with DP. Other connectors are just too problematic:
- Some systems have an HPD pin assigned to LVDS, but it's rarely
if ever connected properly and we don't really care about hpd
events on LVDS anyway since it's always connected.
- The HPD pin is wired up correctly for eDP, but we don't really
have to do anything since the events since it's always connected.
- Some HPD pins fire more than once when you connect/disconnect
- etc.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39882
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Function genpd_queue_power_off_work() is not defined for
CONFIG_PM_RUNTIME, so pm_genpd_poweroff_unused() causes a build
error to happen in that case. Fix the problem by making
pm_genpd_poweroff_unused() depend on CONFIG_PM_RUNTIME too.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
drivers/net/gianfar_ethtool.c:765: warning: the frame size of 2048 bytes is larger than 1024 bytes
Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com>
Reviewed-and-tested-by: Sebastian Pöhn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some buggy chips, "vlan tag present" flag is set which causes packet
loss. Fix this by checking if rx vlan accel is enabled in features.
Reported-by: Michael Guntsche <mguntsche@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By a6b7a40786, remove interrupt.h
from netdevice.h. But this forget to revise sh_eth.
This fix the build failure.
error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_eth_interrupt'
error: implicit declaration of function 'request_irq'
error: 'sh_eth_interrupt' undeclared (first use in this function)
error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1386: error: for each function it appears in.)
error: 'IRQF_SHARED' undeclared (first use in this function)
error: implicit declaration of function 'free_irq'
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this code, the failure_cleanup label calls the function
plx_pci_del_card, which frees everything in the card->net_dev array. dev
is placed in this array immediately after allocation, so the two subsequent
jumps to failure_cleanup should not also call free_sja1000dev, but the
second one does.
If plx_pci_check_sja1000 fails, then free_sja1000dev is also called on
dev. Because dev is already in the card->net_dev array, this implies that
when plx_pci_del_card is later called, it may get freed again. So that
entry is reset to NULL after the free.
Finally, if there is a problem with one channel, there will be a hole in the
array. card->channels counts the number of channels that have succeeded,
and does not keep track of the index of the largest element in the array
that is valid. So the loop in plx_pci_del_card is changed to go up to
PLX_PCI_MAX_CHAN, which is only 2.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_ncm driver still has a few places where stack variables are
passed to the cdc_ncm_do_request function. This triggers a stack trace in
lib/dma-debug.c if the CONFIG_DEBUG_DMA_API option is set.
Adjust these calls to pass parameters that have been allocated with
kzalloc.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan. In promiscuous mode the filter table is cleared to in
order to disable filtering. However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it. As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.
CC: Scott J. Goldman <scottjg@vmware.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix below compile warning:
CC drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts. This makes SDIO work.
Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A header change has removed an implicit inclusion of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
During card removal and inserting cycle the test file in the debugfs could be
stalled until the host driver removes it. Let's keep the file in the linked
list and destroy it when card is removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung SoCs need to set BROKEN_ADMA_ZEROLEN_DESC.
(If ADMA operation is more than 65535, maybe set by zero.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable the quirk.
(Best used in conjunction with patch downgrading ADMA to SDMA when
transfer is not aligned.)
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.
Signed-off-by: Aaron Lu <Aaron.Lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This bug has been introduced by:
d593411084
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Mon Jul 11 10:48:51 2011 +0300
iwlagn: simplify the bus architecture
Revert part of the buggy patch: dev_get_drvdata will now return
iwl_priv as it did before the patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit cc1a93e68f.
This fix introduced a bug: bad pointer in unload.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some older Panasonic made camcorders (Panasonic AG-EZ30 and NV-DX110,
Grundig Scenos DLC 2000) reject requests with ack_busy_X if a request is
sent immediately after they sent a response to a prior transaction.
This causes firewire-core to fail probing of the camcorder with "giving
up on config rom for node id ...". Consequently, programs like kino or
dvgrab are unaware of the presence of a camcorder.
Such transaction failures happen also with the ieee1394 driver stack
(of the 2.4...2.6 kernel series until 2.6.36 inclusive) but with a lower
likelihood, such that kino or dvgrab are generally able to use these
camcorders via the older driver stack. The cause for firewire-ohci's or
firewire-core's worse behavior is not yet known. Gap count optimization
in firewire-core is not the cause. Perhaps the slightly higher latency
of transaction completion in the older stack plays a role. (ieee1394:
AR-resp DMA context tasklet -> packet completion ktread -> user process;
firewire-core: tasklet -> user process.)
This change introduces retries and delays after ack_busy_X into
firewire-core's Config ROM reader, such that at least firewire-core's
probing and /dev/fw* creation are successful. This still leaves the
problem that userland processes are facing transaction failures.
gscanbus's built-in retry routines deal with them successfully, but
neither kino's nor dvgrab's do ever succeed.
But at least DV capture with "dvgrab -noavc -card 0" works now. Live
video preview in kino works too, but not actual capture.
One way to prevent Configuration ROM reading failures in application
programs is to modify libraw1394 to synthesize read responses by means
of firewire-core's Configuration ROM cache. This would only leave
CMP and FCP transaction failures as a potential problem source for
applications.
Reported-and-tested-by: Thomas Seilund <tps@netmaster.dk>
Reported-and-tested-by: René Fritz <rene@colorcube.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When the Manageability Engine (ME) is enabled on 82579, it periodically
accesses some MAC CSR registers. There is an arbiter in hardware which
prevents simultaneous access of these registers by the host software, i.e.
the driver. There is a hardware bug in the aribter that signals a host
access of the registers later than it actually happens. A write of the
Transmit or Receive Descriptor Tail register could result in an incorrect
value if the driver and ME perform simultaneous accesses which could result
in an access to an invalid memory address. This would return an
Unsupported Request which could hang the hardware. Workaround the issue by
checking the FWSM register bit24 which is set by ME before it accesses the
MAC CSR registers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC can drop short packets when the PHY detects noise on the line at
100Mbps due to a timing issue. Workaround the issue by increasing the PLL
counter so the PHY properly recognizes the synchronization pattern from the
MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On 82577/8/9 in half-duplex when a received packet is passed from the PHY
to the MAC, if too many preamble octects are stripped from the packet
before arriving at the MAC, it can be misintrepeted as an in-band message
rather than an actual frame. For example, if the frame contents resembled
an interrupt request in-band message, it would trigger a false interrupt.
In most cases, the packet is just dropped.
By reducing the number of preamble octets stripped from the beginning of
the frame when passing it from the PHY to the MAC, the MAC will interpret
the frame properly.
An additional uses of the magic PHY_REG(770, 16) have been updated with a
define introduced with this patch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to fix a memory leak found via code review for FCOE.
Specifically on DDP flows the SKBs were being dropped without being
recycled, freed, or given to the stack.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: Serial: Add PID(0xF7C0) to FTDI SIO driver for a zeitcontrol-device
USB: Serial: Add device ID for Sierra Wireless MC8305
USB: Serial: Added device ID for Qualcomm Modem in Sagemcom's HiLo3G
usb/host/pci-quirks.c: correct annotation of `ehci_dmi_nohandoff_table'
USB: option driver: add PID for Vodafone-Huawei K4511
USB: option driver: add PID for Vodafone-Huawei K4510
USB: option driver: add PID for Vodafone-Huawei K3771
USB: option driver: add PID for Vodafone-Huawei K3770
usb: serial: ftdi_sio.c: For the FT232H FTDI_SIO_SET_BAUDRATE_REQUEST, index needs to be shifted too
usb/isp1760: Added missing call to usb_hcd_check_unlink_urb() during unlink
USB: EHCI: Fix test mode sequence
USB: ftdi_sio: fix minor typo in get_ftdi_divisor
USB: at91_udc: include linux/prefetch.h explicitly
USB: usb-storage: unusual_devs entry for ARM V2M motherboard.
usb/ehci-mxc: add missing inclusion of mach/hardware.h
USB: assign instead of equal in usbtmc.c
usb: renesas_usbhs: fixup usbhsg_for_each_uep 1st pos
usb: renesas_usbhs: fix DMA build by including dma-mapping.h
usb: gadget: net2272 - Correct includes
usb: musb: fix oops on musb_gadget_pullup
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
zcache: Fix build error when sysfs is not defined
zcache: Use div_u64 for 64-bit division
staging:rts_pstor: fix thread synchronization flow
drivers:staging:solo6x10:add the missed slab.h
staging: zcache: include module.h for MODULE_LICENSE
drivers/staging/hv/blkvsc_drv.c: eliminate NULL pointer dereference
Staging: Add clk API note to nvec/TODO
drivers/staging/ath6kl/miscdrv/ar3kps/ar3kpsparser.c: adjust array index
staging: more missing slab.h inclusions
drivers/staging/solo6x10/p2m.c needs slab.h
drivers/staging/solo6x10/core.c needs slab.h
drivers/staging/dt3155v4l/dt3155v4l.c needs slab.h
drivers/staging/speakup/devsynth.c: fix "buffer size is not provably correct" error
Staging: iio: add some unlocks to raw_read() functions
staging: ft1000_proc needs asm/io.h for inw/outw on sparc
staging: rtl8192u: declare MODULE_FIRMWARE
gma500: Fix clashes with DRM updates
staging: zcache: module is GPL
staging: fix zcache building
In each case, the freed data should be freed in the error handling code
as
well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
e1000e: increase driver version number
e1000e: alternate MAC address update
e1000e: do not disable receiver on 82574/82583
e1000e: alternate MAC address does not work on device id 0x1060
PCnet: Fix section mismatch
bnx2x: disable dcb on 578xx since not supported yet
bnx2x: properly clean indirect addresses
bnx2x: prevent race between undi_unload and load flows
bnx2x: fix select_queue when FCoE is disabled
bnx2x: init FCOE FP only once
ipv4: some rt_iif -> rt_route_iif conversions
net/bridge/netfilter/ebtables.c: use available error handling code
net/netlabel/netlabel_kapi.c: add missing cleanup code
net/irda: sh_sir: tidyup compile warning
net/irda: sh_sir: add missing header
net/irda: sh_irda: add missing header
slcan: ldisc generated skbs are received in softirq context
scm: Capture the full credentials of the scm sender
tcp: initialize variable ecn_ok in syncookies path
drivers/net/wireless/wl1251: add missing kfree
...
If request_irq failed, we would pass wrong arguments to
dma_free_coherent. https://bugzilla.redhat.com/show_bug.cgi?id=728185
Reported-by: Mads Kiilerich
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Clemens points out that we need to use compat_ptr() in order to safely
cast from u64 to addresses of a 32-bit usermode client.
Before, our conversion went wrong
- in practice if the client cast from pointer to integer such that
sign-extension happened, (libraw1394 and libdc1394 at least were not
doing that, IOW were not affected)
or
- in theory on s390 (which doesn't have FireWire though) and on the
tile architecture, regardless of what the client does.
The bug would usually be observed as the initial get_info ioctl failing
with "Bad address" (EFAULT).
Reported-by: Carl Karsten <carl@personnelware.com>
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
At least some Apples program the GPU into a state that wedges the engine
once userspace starts trying to perform accelerated operations. Executing
the Atom init scripts gets the hardware back into a working state. The
same hardware works fine when booted via BIOS emulation, so let's just
execute the init scripts on Apples when we're using EFI.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We have two sources of information about panel capabilities on mobile
radeon - the BIOS, which gives us a native mode, and the panel's preferred
mode. In theory these two will always match, but there's some corner cases
where the BIOS hasn't been fully initialised and so the native mode in it
ends up with default values. However, if we get a panel with reasonable
EDID, it's probably the case that the panel's preferred mode does actually
represent the panel capabilities. This patch handles that case by replacing
the native mode with the panel's preferred mode if the resolutions don't
match. Systems without a valid internal panel EDID will still use the BIOS
native mode.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to add support for 4 crtcs when setting the possible crtcs
for the encoders.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we get a hotplug event on an connector that is off, don't
attempt to turn it on or off, it should already be off.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=728228
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case one "forgot" to load the receiver i.e. doing
|modprobe omap2430
|modprobe musb_hdrc
he ends up with:
|musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
|HS USB OTG: no transceiver configured
|musb-hdrc musb-hdrc: musb_init_controller failed with status -19
|(NULL device *): gadget not registered.
|Unable to handle kernel NULL pointer dereference at virtual address 0000001c
|Internal error: Oops: 17 [#1] SMP
|[<c011383c>] (sysfs_find_dirent+0x4/0x60) from [<c01138c0>] (sysfs_get_dirent+0x28/0x78)
|[<c01138c0>] (sysfs_get_dirent+0x28/0x78) from [<c0115b78>] (sysfs_unmerge_group+0x1c/0x90)
|[<c0115b78>] (sysfs_unmerge_group+0x1c/0x90) from [<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c)
|[<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c) from [<c01742f8>] (device_del+0x40/0x1b4)
|[<c01742f8>] (device_del+0x40/0x1b4) from [<c0174478>] (device_unregister+0xc/0x18)
|[<c0174478>] (device_unregister+0xc/0x18) from [<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc])
|[<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc]) from [<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc])
|[<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc]) from [<c01779c4>] (platform_drv_probe+0x1c/0x24)
The problem is that musb_free() tries to figure out what was
initializued and what wasn't and clean up only the initialized part.
This works well for usb_del_gadget_udc() but device_unregister() can't
deal with it. Therefore we rely on the fact the we always have a parent
device and only then remove the device.
I broke this in 0f91349 ("usb: gadget: convert all users to the new udc
infrastructure")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the prefetch/list.h restructure, drivers need to explicitly include
linux/prefetch.h in order to use the prefetch() function. Otherwise, the
current driver fails to build:
drivers/usb/musb/blackfin.c: In function 'musb_write_fifo':
drivers/usb/musb/blackfin.c:43: error: implicit declaration of function
'prefetch'
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Include dma-mapping.h to fix build of the renesas_usbhs driver
| CC drivers/usb/renesas_usbhs/mod_gadget.o
| drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_map':
| drivers/usb/renesas_usbhs/mod_gadget.c:190: error: implicit declaration of function 'dma_map_single'
| drivers/usb/renesas_usbhs/mod_gadget.c:192: error: implicit declaration of function 'dma_sync_single_for_device'
| drivers/usb/renesas_usbhs/mod_gadget.c:196: error: implicit declaration of function 'dma_mapping_error'
| drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_unmap':
| drivers/usb/renesas_usbhs/mod_gadget.c:217: error: implicit declaration of function 'dma_unmap_single'
| drivers/usb/renesas_usbhs/mod_gadget.c:219: error: implicit declaration of function 'dma_sync_single_for_cpu'
| make[5]: *** [drivers/usb/renesas_usbhs/mod_gadget.o] Error 1
| make[4]: *** [drivers/usb/renesas_usbhs] Error 2
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace DBG with dev_dbg and fix invalid access of musb->controller.
With this patch cppi_dma builds successfully.
Cc: <stable@kernel.org>
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ux500_dma.c fail to compile becase DBG has been removed from musb_debug.
Use dev_dbg for all prints.
Cc: stable@vger.kernel.org
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Mian Yousaf Kaukab<mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dma driver requires both src and dst to be set.
This fix is needed in order to run gadget mass storage.
Patch is verified on snowball.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.
the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.
in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.
[ balbi@ti.com : simplified commit log; removed few things
which didn't belong there ]
Cc: stable@kernel.org
Reported-by: Zach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Obviously, disabling & put regulator and iounmap(hcd->regs)
are missed in .remove and failure handling path of .probe,
so add them.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Keshava Munegowda <Keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CC drivers/usb/musb/tusb6010_omap.o
drivers/usb/musb/tusb6010_omap.c: In function 'tusb_omap_use_shared_dmareq':
drivers/usb/musb/tusb6010_omap.c:92: error: 'musb' undeclared (first use in this function)
drivers/usb/musb/tusb6010_omap.c:92: error: (Each undeclared identifier is reported only once
drivers/usb/musb/tusb6010_omap.c:92: error: for each function it appears in.)
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CONFIG_REGMAP_I2C/SPI are set to m when selected by a tristate config
option that's set to m. The regmap modules don't specify a license, so
fail to link to regmap_init at load time, since that is EXPORT_SYMBOL_GPL.
Fix this by specifying a license for the regmap modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If word 0x37 in the EEPROM is 0xFFFF _or_ 0x0000, then there is no
alternate MAC address in the EEPROM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to a hardware erratum, the receiver on 82574 and 82583 should not be
stopped once it has been started.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This issue is present all the way back to 2.6.34 kernels.
CC: <stable@kernel.org>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeffrey Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rt2800usb_work_txdone we check flags in order:
- ENTRY_OWNER_DEVICE_DATA
- ENTRY_DATA_STATUS_PENDING
- ENTRY_DATA_IO_FAILED
Modify flags in separate order in rt2x00usb_interrupt_txdone, to avoid
processing entries in _txdone with wrong flags or skip processing
ready entries.
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rs_resp is dynamically allocated in aem_read_sensor(), so it should be freed
before exiting in every case. This collects the kfree and the return at
the end of the function.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # 2.6.27+
pmbus_clear_faults() attempts to clear faults on non-existing real pages.
As a result, the command error bit in the status register is set, and faults
are not really cleared.
All byte writes to non-zero pages are requests to clear the status register
on that page. Since non-zero pages are virtual and do not exist on the chip,
there is nothing to do, and such requests have to be ignored. This fixes
above problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
With virtual pages and to be able to handle more chips, it is necessary to
virtualise pmbus_write_byte().
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
If kzalloc for kbc fails, then we have NULL pointer dereference while
calling input_free_device(kbc->idev) in the error handling.
So it is safer to always use the original name, input_dev.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
input_free_device() should be used if input_register_device() was not called
yet or if it failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit af9d220bac.
It turns out that one was meant to be applied on top of the edac.git
tree in -next that has more i7core_edac changes, but that wasn't clear
in the original email.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building MIPS mtx1_defconfig results in:
MODPOST 735 modules
WARNING: drivers/net/pcnet32.o(.devinit.text+0x11ec): Section mismatch in reference from the function pcnet32_probe_vlbus.constprop.22() to the variable .init.data:pcnet32_portlist
The function __devinit pcnet32_probe_vlbus.constprop.22() references
a variable __initdata pcnet32_portlist.
If pcnet32_portlist is only used by pcnet32_probe_vlbus.constprop.22 then
annotate pcnet32_portlist with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidyup below warning
${LINUX}/drivers/net/irda/sh_sir.c:514:6: warning:
'val' may be used uninitialized in this function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixup below build error on sh_sir
sh_sir.c: In function 'sh_sir_write':
sh_sir.c:127:2: error: implicit declaration of function 'iowrite16'
sh_sir.c: In function 'sh_sir_read':
sh_sir.c:132:2: error: implicit declaration of function 'ioread16'
sh_sir.c: At top level:
sh_sir.c:561:20: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_sir_irq'
sh_sir.c: In function 'sh_sir_probe':
sh_sir.c:727:2: error: implicit declaration of function 'ioremap_nocache'
sh_sir.c:727:16: warning: assignment makes pointer from integer without a cast
sh_sir.c:762:2: error: implicit declaration of function 'request_irq'
sh_sir.c:762:23: error: 'sh_sir_irq' undeclared (first use in this function)
sh_sir.c:762:23: note: each undeclared identifier is reported only once for each function it appears in
sh_sir.c:762:35: error: 'IRQF_DISABLED' undeclared (first use in this function)
sh_sir.c:776:2: error: implicit declaration of function 'iounmap'
sh_sir.c: At top level:
sh_sir.c:436:13: warning: 'sh_sir_clear_all_err' defined but not used
sh_sir.c:474:12: warning: 'sh_sir_is_which_phase' defined but not used
sh_sir.c:490:13: warning: 'sh_sir_tx' defined but not used
sh_sir.c:540:13: warning: 'sh_sir_rx' defined but not used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixup below build error on sh_irda
sh_irda.c: In function 'sh_irda_write':
sh_irda.c:174: error: implicit declaration of function 'iowrite16'
sh_irda.c: In function 'sh_irda_read':
sh_irda.c:184: error: implicit declaration of function 'ioread16'
sh_irda.c: At top level:
sh_irda.c:492: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_irda_irq'
sh_irda.c: In function 'sh_irda_probe':
sh_irda.c:776: error: implicit declaration of function 'ioremap_nocache'
sh_irda.c:776: warning: assignment makes pointer from integer without a cast
sh_irda.c:811: error: implicit declaration of function 'request_irq'
sh_irda.c:811: error: 'sh_irda_irq' undeclared (first use in this function)
sh_irda.c:811: error: (Each undeclared identifier is reported only once
sh_irda.c:811: error: for each function it appears in.)
sh_irda.c:811: error: 'IRQF_DISABLED' undeclared (first use in this function)
sh_irda.c:825: error: implicit declaration of function 'iounmap'
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this discussion pointed out
http://marc.info/?l=linux-netdev&m=131257225602375
netdevices that are based on serial line disciplines should use netif_rx_ni()
when pushing received socketbuffers into the netdev rx queue.
Following commit 614851601c ("slip: fix NOHZ
local_softirq_pending 08 warning") this patch updates the slcan driver
accordingly.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Matvejchikov Ilya <matvejchikov@gmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a patch for a new PID (zeitcontrol-device mifare-reader FT232BL(like FT232BM but lead free)).
Signed-off-by: Artur Zimmer <artur128@3dzimmer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A new device ID pair is added for Sierra Wireless MC8305.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: drop experimental status for ARM_PATCH_PHYS_VIRT
ARM: 7008/1: alignment: Make SIGBUS sent to userspace POSIXly correct
ARM: 7007/1: alignment: Prevent ignoring of faults with ARMv6 unaligned access model
ARM: 7010/1: mm: fix invalid loop for poison_init_mem
ARM: 7005/1: freshen up mm/proc-arm946.S
dmaengine: PL08x: Fix trivial build error
ARM: Fix build error for SMP=n builds
In each case, the kfree already at the end of the function is also needed
in the error case.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both AMD and Intel i7 EDAC drivers use MCE features and are thus
dependent of this functionality present in the kernel. Express this in
Kconfig so that randconfig builds don't break.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a driver tries to cancel an URB, and the host controller is dying,
xhci_urb_dequeue will giveback the URB without removing the xhci_tds
that comprise that URB from the td_list or the cancelled_td_list. This
can cause a race condition between the driver calling URB dequeue and
the stop endpoint command watchdog timer.
If the timer fires on a dying host, and a driver attempts to resubmit
while the watchdog timer has dropped the xhci->lock to giveback a
cancelled URB, URBs may be given back by the xhci_urb_dequeue() function.
At that point, the URB's priv pointer will be freed and set to NULL, but
the TDs will remain on the td_list. This will cause an oops in
xhci_giveback_urb_in_irq() when the watchdog timer attempts to loop
through the endpoints' td_lists, giving back killed URBs.
Make sure that xhci_urb_dequeue() removes TDs from the TD lists and
canceled TD lists before it gives back the URB.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When an isochronous transfer is enqueued, xhci_queue_isoc_tx_prepare()
will ensure that there is enough room on the transfer rings for all of the
isochronous TDs for that URB. However, when xhci_queue_isoc_tx() is
enqueueing individual isoc TDs, the prepare_transfer() function can fail
if the endpoint state has changed to disabled, error, or some other
unknown state.
With the current code, if Nth TD (not the first TD) fails, the ring is
left in a sorry state. The partially enqueued TDs are left on the ring,
and the first TRB of the TD is not given back to the hardware. The
enqueue pointer is left on the TRB after the last successfully enqueued
TD. This means the ring is basically useless. Any new transfers will be
enqueued after the failed TDs, which the hardware will never read because
the cycle bit indicates it does not own them. The ring will fill up with
untransferred TDs, and the endpoint will be basically unusable.
The untransferred TDs will also remain on the TD list. Since the td_list
is a FIFO, this basically means the ring handler will be waiting on TDs
that will never be completed (or worse, dereference memory that doesn't
exist any more).
Change the code to clean up the isochronous ring after a failed transfer.
If the first TD failed, simply return and allow the xhci_urb_enqueue
function to free the urb_priv. If the Nth TD failed, first remove the TDs
from the td_list. Then convert the TRBs that were enqueued into No-op
TRBs. Make sure to flip the cycle bit on all enqueued TRBs (including any
link TRBs in the middle or between TDs), but leave the cycle bit of the
first TRB (which will show software-owned) intact. Then move the ring
enqueue pointer back to the first TRB and make sure to change the
xhci_ring's cycle state to what is appropriate for that ring segment.
This ensures that the No-op TRBs will be overwritten by subsequent TDs,
and the hardware will not start executing random TRBs because the cycle
bit was left as hardware-owned.
This bug is unlikely to be hit, but it was something I noticed while
tracking down the watchdog timer issue. I verified that the fix works by
injecting some errors on the 250th isochronous URB queued, although I
could not verify that the ring is in the correct state because uvcvideo
refused to talk to the device after the first usb_submit_urb() failed.
Ring debugging shows that the ring looks correct, however.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When the isochronous transfer support was introduced, and the xHCI driver
switched to using urb->hcpriv to store an "urb_priv" pointer, a couple of
memory leaks were introduced into the URB enqueue function in its error
handling paths.
xhci_urb_enqueue allocates urb_priv, but it doesn't free it if changing
the control endpoint's max packet size fails or the bulk endpoint is in
the middle of allocating or deallocating streams.
xhci_urb_enqueue also doesn't free urb_priv if any of the four endpoint
types' enqueue functions fail. Instead, it expects those functions to
free urb_priv if an error occurs. However, the bulk, control, and
interrupt enqueue functions do not free urb_priv if the endpoint ring is
NULL. It will, however, get freed if prepare_transfer() fails in those
enqueue functions.
Several of the error paths in the isochronous endpoint enqueue function
also fail to free it. xhci_queue_isoc_tx_prepare() doesn't free urb_priv
if prepare_ring() indicates there is not enough room for all the
isochronous TDs in this URB. If individual isochronous TDs fail to be
queued (perhaps due to an endpoint state change), urb_priv is also leaked.
This argues that the freeing of urb_priv should be done in the function
that allocated it, xhci_urb_enqueue.
This patch looks rather ugly, but refactoring the code will have to wait
because this patch needs to be backported to stable kernels.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When a USB2 port initiate a remote wakeup, software shall ensure that
resume is signaled for at least 20ms, and then write '0' to the PLS field.
According to this, xhci driver do the following things:
1. When receive a remote wakeup event in irq_handler, set the resume_done
value as jiffies + 20ms, and modify rh_timer to poll root hub status at
that time;
2. When receive a GetPortStatus request, if the jiffies is after the
resume_done value, clear the resume signal and resume_done.
However, if usb_port_resume() is called before the rh_timer triggered, it
will indicate the port as Suspend Cleared and skip the clear resume signal
part. The device will fail the usb_get_status request in finish_port_resume(),
and usbcore will try a reset-resume instead. Device will work OK after
reset-resume, but resume_done value is not cleared in this case, and
xhci_bus_suspend() will fail because when it finds a non-zero resume_done
value, it will regard the port as resuming and return -EBUSY.
This causes issue on some platforms that the system fail to suspend
after remote wakeup from suspend by USB2 devices connected to xHCI port.
To fix this issue, report the port status as suspend if the resume is
signaling less that 20ms, and usb_port_resume() will wait 25ms and check
port status again, so xHCI driver can clear the resume signaling and
resume_done value.
This should be backported to kernels as old as 2.6.37.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Fix the port U3 status check when Clear PORT_SUSPEND Feature.
The port status should be masked with PORT_PLS_MASK to check if it's in
U3 state.
This should be backported to kernels as old as 2.6.37.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
This cleans up error handling for the beacon in case of dma mapping
failure. We need to free the skb when dma mapping fails instead of
nulling and leaking the pointer, and we should bail out to avoid
giving the hardware the bad descriptor.
Finally, we need to perform the null check after trying to update
the beacon, or else beacons will never be sent after a single
mapping failure.
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add a device id for the wifi usb keys shiped by DVICO with
some of their tvix hardware.
Signed-off-by: Anthony Bourguignon <contact+kernel@toniob.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses an issue with incorrect HW register
AR_PHY_TX_IQCAL_CORR_COEFF_B1 definition which leads to incorrect clibration.
Cc: stable@kernel.org
Signed-off-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Maik-Holger Freudenberg <hhfeuer@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes several problems in the USB_DEVICE table, including missing IDs,
reversed vendor/product codes, and a duplicate ID.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ebefce3d13 failed
to set proper PMU value to address ripple issue for AR9485.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CTL power data incorrect in ctlPowerData_2G field of ar9300_eeprom.
Setting incorrect CTL power in calibration is causing lower tx power.
Tx power was reported as 3dBm while operating in channel 6 HT40+/
in channel 11 HT40- due to CTL powers in the calibration is set to
zero.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This causes an databus error on a Broadcom SoC using bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
