fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com>
Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saravana Kannan says:
====================
Clean up and fix error handling in mdio_mux_init()
This patch series was started due to -EPROBE_DEFER not being handled
correctly in mdio_mux_init() and causing issues [1]. While at it, I also
did some more error handling fixes and clean ups. The -EPROBE_DEFER fix is
the last patch.
Ideally, in the last patch we'd treat any error similar to -EPROBE_DEFER
but I'm not sure if it'll break any board/platforms where some child
mdiobus never successfully registers. If we treated all errors similar to
-EPROBE_DEFER, then none of the child mdiobus will work and that might be a
regression. If people are sure this is not a real case, then I can fix up
the last patch to always fail the entire mdio-mux init if any of the child
mdiobus registration fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa19644 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole point of devm_* APIs is that you don't have to undo them if you
are returning an error that's going to get propagated out of a probe()
function. So delete unnecessary devm_kfree() call in the error return path.
Fixes: b601616681 ("mdio: mux: Correct mdio_mux_init error path issues")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that of_find_compatible_node has a weird calling convention in
which it calls of_node_put() on the "from" node argument, instead of
leaving that up to the caller. This comes from the fact that
of_find_compatible_node with a non-NULL "from" argument it only supposed
to be used as the iterator function of for_each_compatible_node(). OF
iterator functions call of_node_get on the next OF node and of_node_put()
on the previous one.
When of_find_compatible_node calls of_node_put, it actually never
expects the refcount to drop to zero, because the call is done under the
atomic devtree_lock context, and when the refcount drops to zero it
triggers a kobject and a sysfs file deletion, which assume blocking
context.
So any driver call to of_find_compatible_node is probably buggy because
an unexpected of_node_put() takes place.
What should be done is to use the of_get_compatible_child() function.
Fixes: 5a8f09748e ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Link: https://lore.kernel.org/netdev/20210814010139.kzryimmp4rizlznt@skbuf/
Suggested-by: Frank Rowand <frowand.list@gmail.com>
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for using the skb->hash value as the flow hash in CAKE,
I accidentally introduced a logic error that broke the host-only isolation
modes of CAKE (srchost and dsthost keywords). Specifically, the flow_hash
variable should stay initialised to 0 in cake_hash() in pure host-based
hashing mode. Add a check for this before using the skb->hash value as
flow_hash.
Fixes: b0c19ed608 ("sch_cake: Take advantage of skb->hash where appropriate")
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ixgbe_xsk_pool_enable(), if ixgbe_xsk_wakeup() fails,
We should restore the previous state and clean up the
resources. Add the missing clear af_xdp_zc_qps and unmap dma
to fix this bug.
Fixes: d49e286d35 ("ixgbe: add tracking of AF_XDP zero-copy state for each queue pair")
Fixes: 4a9b32f30f ("ixgbe: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210817203736.3529939-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
First set of fixes for v5.14 and nothing major this time. New devices
for iwlwifi and one fix for a compiler warning.
iwlwifi
* support for new devices
mt76
* fix compiler warning about MT_CIPHER_NONE
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmEb7SAVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622bDaEH/1TH5IlBXq4dNPGNwgZ0L4sXFlVk
U7mSbuv2BdH+5edozGwdGl4d6o/vqzcoYSF/dh6d4rpX//zacSsB4LpACW1knlh5
aJxjP5PdxLty/90JXtpBxL79WfQ9kVQ72ldKAg1Gk9XFk1UOqXSaOaLccNBtFk78
n97hNwEeKKX1bw//fNLgyxUAlMoIVCaNjtcY9xJpoC5xLHQxM7ixhxqZF7XSeujQ
z63CRUnT/7gFr4DbOLsZSZVYhCX9v+rz4imIsNbly3e6vLH9Mp2pkyHFfaHKFk6X
tV/Kkd1Bq6OjQAGSq7mbddi7XqXSd3/1rUZChUy0ZSiyKlly52iqxWhWBBI=
=YqJK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2021-08-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.14
First set of fixes for v5.14 and nothing major this time. New devices
for iwlwifi and one fix for a compiler warning.
iwlwifi
* support for new devices
mt76
* fix compiler warning about MT_CIPHER_NONE
* tag 'wireless-drivers-2021-08-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
mt76: fix enum type mismatch
iwlwifi: add new so-jf devices
iwlwifi: add new SoF with JF devices
iwlwifi: pnvm: accept multiple HW-type TLVs
====================
Link: https://lore.kernel.org/r/20210817171027.EC1E6C43460@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
qlcnic_83xx_unlock_flash() is called on all paths after we call
qlcnic_83xx_lock_flash(), except for one error path on failure
of QLCRD32(), which may cause a deadlock. This bug is suggested
by a static analysis tool, please advise.
Fixes: 81d0aeb0a4 ("qlcnic: flash template based firmware reset recovery")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210816131405.24024-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit a02e8964ea ("virtio-net: ethtool configurable LRO")
maps LRO to virtio guest offloading features and allows the
administrator to enable and disable those features via ethtool.
This leads to several issues:
- For a device that doesn't support control guest offloads, the "LRO"
can't be disabled triggering WARN in dev_disable_lro() when turning
off LRO or when enabling forwarding bridging etc.
- For a device that supports control guest offloads, the guest
offloads are disabled in cases of bridging, forwarding etc slowing
down the traffic.
Fix this by using NETIF_F_GRO_HW instead. Though the spec does not
guarantee packets to be re-segmented as the original ones,
we can add that to the spec, possibly with a flag for devices to
differentiate between GRO and LRO.
Further, we never advertised LRO historically before a02e8964ea
("virtio-net: ethtool configurable LRO") and so bridged/forwarded
configs effectively always relied on virtio receive offloads behaving
like GRO - thus even if this breaks any configs it is at least not
a regression.
Fixes: a02e8964ea ("virtio-net: ethtool configurable LRO")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Ivan <ivan@prestigetransportation.com>
Tested-by: Ivan <ivan@prestigetransportation.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix the "reverse-NAT" for replies.
When a packet is sent over a VRF, the POST_ROUTING hooks are called
twice: Once from the VRF interface, and once from the "actual"
interface the packet will be sent from:
1) First SNAT: l3mdev_l3_out() -> vrf_l3_out() -> .. -> vrf_output_direct()
This causes the POST_ROUTING hooks to run.
2) Second SNAT: 'ip_output()' calls POST_ROUTING hooks again.
Similarly for replies, first ip_rcv() calls PRE_ROUTING hooks, and
second vrf_l3_rcv() calls them again.
As an example, consider the following SNAT rule:
> iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j SNAT --to-source 2.2.2.2 -o vrf_1
In this case sending over a VRF will create 2 conntrack entries.
The first is from the VRF interface, which performs the IP SNAT.
The second will run the SNAT, but since the "expected reply" will remain
the same, conntrack randomizes the source port of the packet:
e..g With a socket bound to 1.1.1.1:10000, sending to 3.3.3.3:53, the conntrack
rules are:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=0 bytes=0 mark=0 use=1
udp 17 29 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
i.e. First SNAT IP from 1.1.1.1 --> 2.2.2.2, and second the src port is
SNAT-ed from 10000 --> 61033.
But when a reply is sent (3.3.3.3:53 -> 2.2.2.2:61033) only the later
conntrack entry is matched:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=1 bytes=49 mark=0 use=1
udp 17 28 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
And a "port 61033 unreachable" ICMP packet is sent back.
The issue is that when PRE_ROUTING hooks are called from vrf_l3_rcv(),
the skb already has a conntrack flow attached to it, which means
nf_conntrack_in() will not resolve the flow again.
This means only the dest port is "reverse-NATed" (61033 -> 10000) but
the dest IP remains 2.2.2.2, and since the socket is bound to 1.1.1.1 it's
not received.
This can be verified by logging the 4-tuple of the packet in '__udp4_lib_rcv()'.
The fix is then to reset the flow when skb is received on a VRF, to let
conntrack resolve the flow again (which now will hit the earlier flow).
To reproduce: (Without the fix "Got pkt_to_nat_port" will not be printed by
running 'bash ./repro'):
$ cat run_in_A1.py
import logging
logging.getLogger("scapy.runtime").setLevel(logging.ERROR)
from scapy.all import *
import argparse
def get_packet_to_send(udp_dst_port, msg_name):
return Ether(src='11:22:33:44:55:66', dst=iface_mac)/ \
IP(src='3.3.3.3', dst='2.2.2.2')/ \
UDP(sport=53, dport=udp_dst_port)/ \
Raw(f'{msg_name}\x0012345678901234567890')
parser = argparse.ArgumentParser()
parser.add_argument('-iface_mac', dest="iface_mac", type=str, required=True,
help="From run_in_A3.py")
parser.add_argument('-socket_port', dest="socket_port", type=str,
required=True, help="From run_in_A3.py")
parser.add_argument('-v1_mac', dest="v1_mac", type=str, required=True,
help="From script")
args, _ = parser.parse_known_args()
iface_mac = args.iface_mac
socket_port = int(args.socket_port)
v1_mac = args.v1_mac
print(f'Source port before NAT: {socket_port}')
while True:
pkts = sniff(iface='_v0', store=True, count=1, timeout=10)
if 0 == len(pkts):
print('Something failed, rerun the script :(', flush=True)
break
pkt = pkts[0]
if not pkt.haslayer('UDP'):
continue
pkt_sport = pkt.getlayer('UDP').sport
print(f'Source port after NAT: {pkt_sport}', flush=True)
pkt_to_send = get_packet_to_send(pkt_sport, 'pkt_to_nat_port')
sendp(pkt_to_send, '_v0', verbose=False) # Will not be received
pkt_to_send = get_packet_to_send(socket_port, 'pkt_to_socket_port')
sendp(pkt_to_send, '_v0', verbose=False)
break
$ cat run_in_A2.py
import socket
import netifaces
print(f"{netifaces.ifaddresses('e00000')[netifaces.AF_LINK][0]['addr']}",
flush=True)
s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
s.setsockopt(socket.SOL_SOCKET, socket.SO_BINDTODEVICE,
str('vrf_1' + '\0').encode('utf-8'))
s.connect(('3.3.3.3', 53))
print(f'{s. getsockname()[1]}', flush=True)
s.settimeout(5)
while True:
try:
# Periodically send in order to keep the conntrack entry alive.
s.send(b'a'*40)
resp = s.recvfrom(1024)
msg_name = resp[0].decode('utf-8').split('\0')[0]
print(f"Got {msg_name}", flush=True)
except Exception as e:
pass
$ cat repro.sh
ip netns del A1 2> /dev/null
ip netns del A2 2> /dev/null
ip netns add A1
ip netns add A2
ip -n A1 link add _v0 type veth peer name _v1 netns A2
ip -n A1 link set _v0 up
ip -n A2 link add e00000 type bond
ip -n A2 link add lo0 type dummy
ip -n A2 link add vrf_1 type vrf table 10001
ip -n A2 link set vrf_1 up
ip -n A2 link set e00000 master vrf_1
ip -n A2 addr add 1.1.1.1/24 dev e00000
ip -n A2 link set e00000 up
ip -n A2 link set _v1 master e00000
ip -n A2 link set _v1 up
ip -n A2 link set lo0 up
ip -n A2 addr add 2.2.2.2/32 dev lo0
ip -n A2 neigh add 1.1.1.10 lladdr 77:77:77:77:77:77 dev e00000
ip -n A2 route add 3.3.3.3/32 via 1.1.1.10 dev e00000 table 10001
ip netns exec A2 iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j \
SNAT --to-source 2.2.2.2 -o vrf_1
sleep 5
ip netns exec A2 python3 run_in_A2.py > x &
XPID=$!
sleep 5
IFACE_MAC=`sed -n 1p x`
SOCKET_PORT=`sed -n 2p x`
V1_MAC=`ip -n A2 link show _v1 | sed -n 2p | awk '{print $2'}`
ip netns exec A1 python3 run_in_A1.py -iface_mac ${IFACE_MAC} -socket_port \
${SOCKET_PORT} -v1_mac ${SOCKET_PORT}
sleep 5
kill -9 $XPID
wait $XPID 2> /dev/null
ip netns del A1
ip netns del A2
tail x -n 2
rm x
set +x
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: Lahav Schlesinger <lschlesinger@drivenets.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210815120002.2787653-1-lschlesinger@drivenets.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bounds check on "index" doesn't catch negative values. Using
ARRAY_SIZE() directly is more readable and more robust because it prevents
negative values for "index". Fortunately we only pass valid values to
ipc_chnl_cfg_get() so this patch does not affect runtime.
Reported-by: Solomon Ucko <solly.ucko@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: 2 bug fixes
The first one disables aRFS/NTUPLE on an older broken firmware version.
The second one adds missing memory barriers related to completion ring
handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple
filters are inserted and deleted by the 212 firmware.
Fixes: ae10ae740a ("bnxt_en: Add new hardware RFS mode.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a possible null-pointer dereference in qed_rdma_create_qp().
Changes from V2:
- Revert checkpatch fixes.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoiding qed ll2 race condition and NULL pointer dereference as part
of the remove and recovery flows.
Changes form V1:
- Change (!p_rx->set_prod_addr).
- qed_ll2.c checkpatch fixes.
Change from V2:
- Revert "qed_ll2.c checkpatch fixes".
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__tipc_sendmsg() is called to send SYN packet by either tipc_sendmsg()
or tipc_connect(). The difference is in tipc_connect(), it will call
tipc_wait_for_connect() after __tipc_sendmsg() to wait until connecting
is done. So there's no need to wait in __tipc_sendmsg() for this case.
This patch is to fix it by calling tipc_wait_for_connect() only when dlen
is not 0 in __tipc_sendmsg(), which means it's called by tipc_connect().
Note this also fixes the failure in tipcutils/test/ptts/:
# ./tipcTS &
# ./tipcTC 9
(hang)
Fixes: 36239dab6da7 ("tipc: fix implicit-connect for SYN+")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb0 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.6.0-rc3-syzkaller #0
...
Workqueue: events_unbound flush_to_ldisc
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x32 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:641
__asan_report_store1_noabort+0x17/0x20 mm/kasan/generic_report.c:137
decode_data.part.0+0x23b/0x270 drivers/net/hamradio/6pack.c:843
decode_data drivers/net/hamradio/6pack.c:965 [inline]
sixpack_decode drivers/net/hamradio/6pack.c:968 [inline]
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal tests found out that the latest code doesn't bring up 1PPS out
as expected. As a result of incorrect define used to round the time up
the time was round down to the past second boundary.
Fix define used for rounding to properly round up to the next Top of
second in ice_ptp_cfg_clkout to fix it.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210813165018.2196013-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
bnxt: Tx NAPI disabling resiliency improvements
A lockdep warning was triggered by netpoll because napi poll
was taking the xmit lock. Fix that and a couple more issues
noticed while reading the code.
====================
Link: https://lore.kernel.org/r/20210812214242.578039-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drivers should count packets they are dropping.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.
Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.
The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.
Noticed while reading the code.
Fixes: 4d172f21ce ("bnxt_en: Implement xmit_more.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca ("bnxt_en: cleanup DIM work on device shutdown")
Fixes: 6a8788f256 ("bnxt_en: add support for software dynamic interrupt moderation")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
can and ieee802154.
Current release - regressions:
- r8169: fix ASPM-related link-up regressions
- bridge: fix flags interpretation for extern learn fdb entries
- phy: micrel: fix link detection on ksz87xx switch
- Revert "tipc: Return the correct errno code"
- ptp: fix possible memory leak caused by invalid cast
Current release - new code bugs:
- bpf: add missing bpf_read_[un]lock_trace() for syscall program
- bpf: fix potentially incorrect results with bpf_get_local_storage()
- page_pool: mask the page->signature before the checking, avoid
dma mapping leaks
- netfilter: nfnetlink_hook: 5 fixes to information in netlink dumps
- bnxt_en: fix firmware interface issues with PTP
- mlx5: Bridge, fix ageing time
Previous releases - regressions:
- linkwatch: fix failure to restore device state across suspend/resume
- bareudp: fix invalid read beyond skb's linear data
Previous releases - always broken:
- bpf: fix integer overflow involving bucket_size
- ppp: fix issues when desired interface name is specified via netlink
- wwan: mhi_wwan_ctrl: fix possible deadlock
- dsa: microchip: ksz8795: fix number of VLAN related bugs
- dsa: drivers: fix broken backpressure in .port_fdb_dump
- dsa: qca: ar9331: make proper initial port defaults
Misc:
- bpf: add lockdown check for probe_write_user helper
- netfilter: conntrack: remove offload_pickup sysctl before 5.14 is out
- netfilter: conntrack: collect all entries in one cycle,
heuristically slow down garbage collection scans
on idle systems to prevent frequent wake ups
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=hzDl
-----END PGP SIGNATURE-----
Merge tag 'net-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter, bpf, can and
ieee802154.
The size of this is pretty normal, but we got more fixes for 5.14
changes this week than last week. Nothing major but the trend is the
opposite of what we like. We'll see how the next week goes..
Current release - regressions:
- r8169: fix ASPM-related link-up regressions
- bridge: fix flags interpretation for extern learn fdb entries
- phy: micrel: fix link detection on ksz87xx switch
- Revert "tipc: Return the correct errno code"
- ptp: fix possible memory leak caused by invalid cast
Current release - new code bugs:
- bpf: add missing bpf_read_[un]lock_trace() for syscall program
- bpf: fix potentially incorrect results with bpf_get_local_storage()
- page_pool: mask the page->signature before the checking, avoid dma
mapping leaks
- netfilter: nfnetlink_hook: 5 fixes to information in netlink dumps
- bnxt_en: fix firmware interface issues with PTP
- mlx5: Bridge, fix ageing time
Previous releases - regressions:
- linkwatch: fix failure to restore device state across
suspend/resume
- bareudp: fix invalid read beyond skb's linear data
Previous releases - always broken:
- bpf: fix integer overflow involving bucket_size
- ppp: fix issues when desired interface name is specified via
netlink
- wwan: mhi_wwan_ctrl: fix possible deadlock
- dsa: microchip: ksz8795: fix number of VLAN related bugs
- dsa: drivers: fix broken backpressure in .port_fdb_dump
- dsa: qca: ar9331: make proper initial port defaults
Misc:
- bpf: add lockdown check for probe_write_user helper
- netfilter: conntrack: remove offload_pickup sysctl before 5.14 is
out
- netfilter: conntrack: collect all entries in one cycle,
heuristically slow down garbage collection scans on idle systems to
prevent frequent wake ups"
* tag 'net-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
vsock/virtio: avoid potential deadlock when vsock device remove
wwan: core: Avoid returning NULL from wwan_create_dev()
net: dsa: sja1105: unregister the MDIO buses during teardown
Revert "tipc: Return the correct errno code"
net: mscc: Fix non-GPL export of regmap APIs
net: igmp: increase size of mr_ifc_count
MAINTAINERS: switch to my OMP email for Renesas Ethernet drivers
tcp_bbr: fix u32 wrap bug in round logic if bbr_init() called after 2B packets
net: pcs: xpcs: fix error handling on failed to allocate memory
net: linkwatch: fix failure to restore device state across suspend/resume
net: bridge: fix memleak in br_add_if()
net: switchdev: zero-initialize struct switchdev_notifier_fdb_info emitted by drivers towards the bridge
net: bridge: fix flags interpretation for extern learn fdb entries
net: dsa: sja1105: fix broken backpressure in .port_fdb_dump
net: dsa: lantiq: fix broken backpressure in .port_fdb_dump
net: dsa: lan9303: fix broken backpressure in .port_fdb_dump
net: dsa: hellcreek: fix broken backpressure in .port_fdb_dump
bpf, core: Fix kernel-doc notation
net: igmp: fix data-race in igmp_ifc_timer_expire()
net: Fix memory leak in ieee802154_raw_deliver
...
and a reference handling fix from Jeff that should address some memory
corruption reports in the snaprealm area. Both marked for stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmEVaqsTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi/DBCACd7+mnAXIwajwoDdXFIJT7/tfimdvU
cMrh6ciZNtEKxm23flQ1AFJXlXR/nlZRspfOmlmsl9bB4TAlXnhJ/s4JaiuOMMTh
OQ4oz0vAbGELkPsXB/FXGSSk1wTFEjCocFsJwoYiUkYjD7Qt12BZKNkFYgj/MVc2
wyJ5K1buqBLVFDU+CymqDzc07YpG1zn888o7UGWFTyevldRAHl2euxqbnr0S4qb9
OS5UKO3aFCEt5PT9RKRHygCGjuHym/fgXgPm9aNY4rYBE9qOXloVUOD5bhMHBJ2E
g506xhOurqbGv4O9oj+gvBwtQwY/TF8BvCA79koQSHNIYQsC/bcXenST
=m8x8
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.14-rc6' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A patch to avoid a soft lockup in ceph_check_delayed_caps() from Luis
and a reference handling fix from Jeff that should address some memory
corruption reports in the snaprealm area.
Both marked for stable"
* tag 'ceph-for-5.14-rc6' of git://github.com/ceph/ceph-client:
ceph: take snap_empty_lock atomically with snaprealm refcount change
ceph: reduce contention in ceph_check_delayed_caps()
amdgpu:
- Yellow carp update
- RAS EEPROM fixes
- BACO/BOCO fixes
- Fix a memory leak in an error path
- Freesync fix
- VCN harvesting fix
- Display fixes
i915:
- GVT fix for Windows VM hang.
- Display fix of 12 BPC bits for display 12 and newer.
- Don't try to access some media register for fused off domains.
- Fix kerneldoc build warnings.
mediatek:
- Fix dpi bridge bug.
- Fix cursor plane no update.
meson:
- Fix colors when booting with HDR
-----BEGIN PGP SIGNATURE-----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=w0XU
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2021-08-13' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Another week, another set of pretty regular fixes, nothing really
stands out too much.
amdgpu:
- Yellow carp update
- RAS EEPROM fixes
- BACO/BOCO fixes
- Fix a memory leak in an error path
- Freesync fix
- VCN harvesting fix
- Display fixes
i915:
- GVT fix for Windows VM hang.
- Display fix of 12 BPC bits for display 12 and newer.
- Don't try to access some media register for fused off domains.
- Fix kerneldoc build warnings.
mediatek:
- Fix dpi bridge bug.
- Fix cursor plane no update.
meson:
- Fix colors when booting with HDR"
* tag 'drm-fixes-2021-08-13' of git://anongit.freedesktop.org/drm/drm:
drm/doc/rfc: drop lmem uapi section
drm/i915: Only access SFC_DONE when media domain is not fused off
drm/i915/display: Fix the 12 BPC bits for PIPE_MISC reg
drm/amd/display: use GFP_ATOMIC in amdgpu_dm_irq_schedule_work
drm/amd/display: Remove invalid assert for ODM + MPC case
drm/amd/pm: bug fix for the runtime pm BACO
drm/amdgpu: handle VCN instances when harvesting (v2)
drm/meson: fix colour distortion from HDR set during vendor u-boot
drm/i915/gvt: Fix cached atomics setting for Windows VM
drm/amdgpu: Add preferred mode in modeset when freesync video mode's enabled.
drm/amd/pm: Fix a memory leak in an error handling path in 'vangogh_tables_init()'
drm/amdgpu: don't enable baco on boco platforms in runpm
drm/amdgpu: set RAS EEPROM address from VBIOS
drm/amd/pm: update smu v13.0.1 firmware header
drm/mediatek: Fix cursor plane no update
drm/mediatek: mtk-dpi: Set out_fmt from config if not the last bridge
drm/mediatek: dpi: Fix NULL dereference in mtk_dpi_bridge_atomic_check
* meson: Fix colors when booting with HDR
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmEU27UACgkQaA3BHVML
eiMABwf+Kuvyh6mXHewMwqRNnxYFwyyhy5AVJm17Z74pZcbxSWp2+WBxDTaugCRX
Dl5Yt27DsCCW0JFpZ0w4xITizUxhD/VKnVUONBB1HK1s92h7WxG+2SQEPQ7uHQj5
iBbaysCn5uIJhpDnTXcqos0wnLMxkquZ5ZK6uQwPD+Q8VsAwMVw0dZ1C/Kkmo9zF
55VUATGIGBtOI4FEDJfDZGukVfbDt28ipMNeyCiqfzREnDeIyojJ/KEbSD3XHhi7
HMDkeAM5SHToNaBEIaEikPWKSSa/b5P3y9U/yT6d4MZ1PH/lr1he4SQnThcTRCg8
+vnMC1iJiwgdX7gQ2StHBoB1GMqv1Q==
=NuGL
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2021-08-12' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Short summary of fixes pull:
* meson: Fix colors when booting with HDR
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YRTb+qUuBYWjJDVg@linux-uq9g.fritz.box
- Display fix of 12 BPC bits for display 12 and newer.
- Don't try to access some media register for fused off domains.
- Fix kerneldoc build warnings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmEVP3QACgkQ+mJfZA7r
E8qGKQgApmIuFnhFspZ2BMsbhxOckZW7mxg+4RzNbIZ/pb+2aO8CnkfemrYZgFX/
OaZtvJdqtbbkN25glZTeP7wuV//uXSkPdr7zTqaL+005U0PL+EUzlfYZR4AzdhI2
D2AMEDfVwwbMrB/hI8sk01XKmEXFfBkX3Acy9svLqi2TOvFCqjnBcV/E5K+eklDs
lY5KoklziRKw2FpckOdKYPiyjWbTC02s7Co4QXdkkSoZm69HDGuBlchH2JNyDrer
Dyarp5btGzkVMZy5q9avIsBgFE1RRVCEnGLaSzMi1qtNaorCTYs5FJtp48yFfmzi
O1X6XOGYDS4nGl782sfxjkOaUNOdbQ==
=vN7o
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2021-08-12' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- GVT fix for Windows VM hang.
- Display fix of 12 BPC bits for display 12 and newer.
- Don't try to access some media register for fused off domains.
- Fix kerneldoc build warnings.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YRU/hnQ1sNr+j37x@intel.com
Stefan Schmidt says:
====================
ieee802154 for net 2021-08-12
Mostly fixes coming from bot reports. Dongliang Mu tackled some syzkaller
reports in hwsim again and Takeshi Misawa a memory leak in ieee802154 raw.
* tag 'ieee802154-for-davem-2021-08-12' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
net: Fix memory leak in ieee802154_raw_deliver
ieee802154: hwsim: fix GPF in hwsim_new_edge_nl
ieee802154: hwsim: fix GPF in hwsim_set_edge_lqi
====================
Link: https://lore.kernel.org/r/20210812183912.1663996-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's a potential deadlock case when remove the vsock device or
process the RESET event:
vsock_for_each_connected_socket:
spin_lock_bh(&vsock_table_lock) ----------- (1)
...
virtio_vsock_reset_sock:
lock_sock(sk) --------------------- (2)
...
spin_unlock_bh(&vsock_table_lock)
lock_sock() may do initiative schedule when the 'sk' is owned by
other thread at the same time, we would receivce a warning message
that "scheduling while atomic".
Even worse, if the next task (selected by the scheduler) try to
release a 'sk', it need to request vsock_table_lock and the deadlock
occur, cause the system into softlockup state.
Call trace:
queued_spin_lock_slowpath
vsock_remove_bound
vsock_remove_sock
virtio_transport_release
__vsock_release
vsock_release
__sock_release
sock_close
__fput
____fput
So we should not require sk_lock in this case, just like the behavior
in vhost_vsock or vmci.
Fixes: 0ea9e1d3a9 ("VSOCK: Introduce virtio_transport.ko")
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20210812053056.1699-1-longpeng2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull ucounts fix from Eric Biederman:
"This fixes the ucount sysctls on big endian architectures.
The counts were expanded to be longs instead of ints, and the sysctl
code was overlooked, so only the low 32bit were being processed. On
litte endian just processing the low 32bits is fine, but on 64bit big
endian processing just the low 32bits results in the high order bits
instead of the low order bits being processed and nothing works
proper.
This change took a little bit to mature as we have the SYSCTL_ZERO,
and SYSCTL_INT_MAX macros that are only usable for sysctls operating
on ints, but unfortunately are not obviously broken. Which resulted in
the versions of this change working on big endian and not on little
endian, because the int SYSCTL_ZERO when extended 64bit wound up being
0x100000000. So we only allowed values greater than 0x100000000 and
less than 0faff. Which unfortunately broken everything that tried to
set the sysctls. (First reported with the windows subsystem for
linux).
I have tested this on x86_64 64bit after first reproducing the
problems with the earlier version of this change, and then verifying
the problems do not exist when we use appropriate long min and max
values for extra1 and extra2"
* 'for-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: add missing data type changes
Make wwan_create_dev() to return either valid or error pointer,
In some cases it may return NULL. Prevent this by converting
it to the respective error pointer.
Fixes: 9a44c1cc63 ("net: Add a WWAN subsystem")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20210811124845.10955-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We still have quite a bit more work to do with overall reworking of
the ttm-based dg1 code, but the uapi stuff is now finalized with the
latest pull. So remove that.
This also fixes kerneldoc build warnings because we've included the
same headers in two places, resulting in sphinx complaining about
duplicated symbols. This regression has been created when we moved the
uapi definitions to the real include/uapi/ folder in 727ecd99a4
("drm/doc/rfc: drop the i915_gem_lmem.h header")
v2: Fix a few references that I missed, the htmldocs build took
forever.
Acked-by: Jason Ekstrand <jason@jlekstrand.net>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by Stephen Rothwell <sfr@canb.auug.org.au> (v1)
References: https://lore.kernel.org/dri-devel/20210603193242.1ce99344@canb.auug.org.au/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 727ecd99a4 ("drm/doc/rfc: drop the i915_gem_lmem.h header")
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210810142748.1983271-1-daniel.vetter@ffwll.ch
(cherry picked from commit dae2d28832)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The SFC_DONE register lives within the corresponding VD0/VD2/VD4/VD6
forcewake domain and is not accessible if the vdbox in that domain is
fused off and the forcewake is not initialized.
This mistake went unnoticed because until recently we were using the
wrong register offset for the SFC_DONE register; once the register
offset was corrected, we started hitting errors like
<4> [544.989065] i915 0000:cc:00.0: Uninitialized forcewake domain(s) 0x80 accessed at 0x1ce000
on parts with fused-off vdbox engines.
Fixes: e50dbdbfd9 ("drm/i915/tgl: Add SFC instdone to error state")
Fixes: 9c9c6d0ab0 ("drm/i915: Correct SFC_DONE register offset")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210806174130.1058960-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit c5589bb5dc)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Changed Fixes tag to match the cherry-picked 82929a2140]
Till DISPLAY12 the PIPE_MISC bits 5-7 are used to set the
Dithering BPC, with valid values of 6, 8, 10 BPC.
For ADLP+ these bits are used to set the PORT OUTPUT BPC, with valid
values of: 6, 8, 10, 12 BPC, and need to be programmed whether
dithering is enabled or not.
This patch:
-corrects the bits 5-7 for PIPE MISC register for 12 BPC.
-renames the bits and mask to have generic names for these bits for
dithering bpc and port output bpc.
v3: Added a note for MIPI DSI which uses the PIPE_MISC for readout
for pipe_bpp. (Uma Shankar)
v2: Added 'display' to the subject and fixes tag. (Uma Shankar)
Fixes: 756f85cffe ("drm/i915/bdw: Broadwell has PIPEMISC")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210811051857.109723-1-ankit.k.nautiyal@intel.com
(cherry picked from commit 70418a6871)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The call to sja1105_mdiobus_unregister is present in the error path but
absent from the main driver unbind path.
Fixes: 5a8f09748e ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0efea3c649 because of:
- The returning -ENOBUF error is fine on socket buffer allocation.
- There is side effect in the calling path
tipc_node_xmit()->tipc_link_xmit() when checking error code returning.
Fixes: 0efea3c649 ("tipc: Return the correct errno code")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot driver makes use of regmap, wrapping it with driver specific
operations that are thin wrappers around the core regmap APIs. These are
exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap
exports which is frowned upon. Add _GPL suffixes to at least the APIs that
are doing register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some arches support cmpxchg() on 4-byte and 8-byte only.
Increase mr_ifc_count width to 32bit to fix this problem.
Fixes: 4a2b285e7e ("net: igmp: fix data-race in igmp_ifc_timer_expire()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210811195715.3684218-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I'm still going to continue looking after the Renesas Ethernet drivers and
device tree bindings. Now my new employer, Open Mobile Platform (OMP), will
pay for all my upstream work. Let's switch to my OMP email for the reviews.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/9c212711-a0d7-39cd-7840-ff7abf938da1@omp.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently if BBR congestion control is initialized after more than 2B
packets have been delivered, depending on the phase of the
tp->delivered counter the tracking of BBR round trips can get stuck.
The bug arises because if tp->delivered is between 2^31 and 2^32 at
the time the BBR congestion control module is initialized, then the
initialization of bbr->next_rtt_delivered to 0 will cause the logic to
believe that the end of the round trip is still billions of packets in
the future. More specifically, the following check will fail
repeatedly:
!before(rs->prior_delivered, bbr->next_rtt_delivered)
and thus the connection will take up to 2B packets delivered before
that check will pass and the connection will set:
bbr->round_start = 1;
This could cause many mechanisms in BBR to fail to trigger, for
example bbr_check_full_bw_reached() would likely never exit STARTUP.
This bug is 5 years old and has not been observed, and as a practical
matter this would likely rarely trigger, since it would require
transferring at least 2B packets, or likely more than 3 terabytes of
data, before switching congestion control algorithms to BBR.
This patch is a stable candidate for kernels as far back as v4.9,
when tcp_bbr.c was added.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Kevin Yang <yyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210811024056.235161-1-ncardwell@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
