Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GPIO card detection pin (mmc0_cd_pin) is already requested and
configured by mmc_gpiod_request_cd() in drivers/mmc/core/slot-gpio.c
so pinctrl is not needed.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch fixes the warning "xxx has a unit name, but no reg property"
by removing "@0" from such node. 6 board files are fixed. Each has the
same aforementioned issue in pinmux nodes. These include the Nano Pi
family base dtsi file, the Orange Pi 2, Orange Pi Lite, Orange Pi One,
Orange Pi PC, and Orange Pi Plus.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Squashed 6 patches together; boards named in commit log]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides a common file for NanoPi M1 and Neo SBC.
Those have common features below.
* UART0
* 2 LEDs
* USB host (EHCI3, OHCI3) and PHY
* MicroSD
* GPIO key switch
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
