The WCD938x comes with three devices on two Linux drivers:
1. RX Soundwire device (wcd938x-sdw.c driver),
2. TX Soundwire device, which is used to access devices via regmap (also
wcd938x-sdw.c driver),
3. platform device (wcd938x.c driver) - glue and component master,
actually having most of the code using TX Soundwire device regmap.
When RX and TX Soundwire devices probe, the component master (platform
device) bind tries to write micbias configuration via TX Soundwire
regmap. This might happen before TX Soundwire enumerates, so the regmap
access fails. On Qualcomm SM8550 board with WCD9385:
qcom-soundwire 6d30000.soundwire-controller: Qualcomm Soundwire controller v2.0.0 Registered
wcd938x_codec audio-codec: bound sdw:0:0217:010d:00:4 (ops wcd938x_sdw_component_ops)
wcd938x_codec audio-codec: bound sdw:0:0217:010d:00:3 (ops wcd938x_sdw_component_ops)
qcom-soundwire 6ad0000.soundwire-controller: swrm_wait_for_wr_fifo_avail err write overflow
Fix the issue by:
1. Moving the regmap creation from platform device to TX Soundwire
device. The regmap settings are moved as-is with one difference:
making the wcd938x_regmap_config const.
2. Using regmap in cache only mode till the actual TX Soundwire device
enumerates and then sync the regmap cache.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20230503144102.242240-1-krzysztof.kozlowski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Make test_resume work again after the changes that made hibernation
open the snapshot device in exclusive mode (Chen Yu).
- Clean up code in several places in intel_idle (Artem Bityutskiy).
-----BEGIN PGP SIGNATURE-----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=CwBd
-----END PGP SIGNATURE-----
Merge tag 'pm-6.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These fix a hibernation test mode regression and clean up the
intel_idle driver.
Specifics:
- Make test_resume work again after the changes that made hibernation
open the snapshot device in exclusive mode (Chen Yu)
- Clean up code in several places in intel_idle (Artem Bityutskiy)"
* tag 'pm-6.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: mark few variables as __read_mostly
intel_idle: do not sprinkle module parameter definitions around
intel_idle: fix confusing message
intel_idle: improve C-state flags handling robustness
intel_idle: further intel_idle_init_cstates_icpu() cleanup
intel_idle: clean up intel_idle_init_cstates_icpu()
intel_idle: use pr_info() instead of printk()
PM: hibernate: Do not get block device exclusively in test_resume mode
PM: hibernate: Turn snapshot_test into global variable
- Do not turn off unused power resources during initialization on the
Toshiba Click Mini (Hans de Goede).
- Support strings in device properties supplied by ACPI _DSM on Apple
platforms (Hector Martin).
- Add an ACPI device ID quirk for Lenovo Yoga Tablet 2 (Marius Hoch).
-----BEGIN PGP SIGNATURE-----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=XhG2
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add two ACPI-related quirks and extend support for Apple device
properties supplied via ACPI _DSM.
Specifics:
- Do not turn off unused power resources during initialization on the
Toshiba Click Mini (Hans de Goede)
- Support strings in device properties supplied by ACPI _DSM on Apple
platforms (Hector Martin)
- Add an ACPI device ID quirk for Lenovo Yoga Tablet 2 (Marius Hoch)"
* tag 'acpi-6.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: property: Support strings in Apple _DSM props
ACPI: x86: utils: Remove Lenovo Yoga Tablet 2's MAGN0001
ACPI: PM: Do not turn of unused power resources on the Toshiba Click Mini
- Add compatible DT bindings for imx6sll and imx6ul to fix a dtbs check
warning (Stefan Wahren).
- Update the example in the DT bindings to reflect changes with the
ADC node name for QCom TM and TM5 (Marijn Suijten).
- Fix comments for the cpuidle_cooling_register() function to match the
function prototype (Chenggang Wang).
- Fix inconsistent temperature read and some Mediatek variant board
reboot by reverting a change and handling the temperature
differently (AngeloGioacchino Del Regno).
- Fix a memory leak in the initialization error path for the Mediatek
driver (Kang Chen).
- Use of_address_to_resource() in the Mediatek driver (Rob Herring).
- Fix unit address in the QCom tsens driver DT bindings (Krzysztof
Kozlowski).
- Clean up the step-wise thermal governor (Zhang Rui).
- Introduce thermal_zone_device() for accessing the device field of
struct thermal_zone_device and two drivers use it (Daniel Lezcano).
- Clean up the ACPI thermal driver a bit (Daniel Lezcano).
- Delete the thermal driver for Intel Menlow platforms that is not
expected to have any users (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----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=/bW2
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These are mostly cleanups on top of the previously merged thermal
control changes plus some driver fixes and the removal of the Intel
Menlow thermal driver.
Specifics:
- Add compatible DT bindings for imx6sll and imx6ul to fix a dtbs
check warning (Stefan Wahren)
- Update the example in the DT bindings to reflect changes with the
ADC node name for QCom TM and TM5 (Marijn Suijten)
- Fix comments for the cpuidle_cooling_register() function to match
the function prototype (Chenggang Wang)
- Fix inconsistent temperature read and some Mediatek variant board
reboot by reverting a change and handling the temperature
differently (AngeloGioacchino Del Regno)
- Fix a memory leak in the initialization error path for the Mediatek
driver (Kang Chen)
- Use of_address_to_resource() in the Mediatek driver (Rob Herring)
- Fix unit address in the QCom tsens driver DT bindings (Krzysztof
Kozlowski)
- Clean up the step-wise thermal governor (Zhang Rui)
- Introduce thermal_zone_device() for accessing the device field of
struct thermal_zone_device and two drivers use it (Daniel Lezcano)
- Clean up the ACPI thermal driver a bit (Daniel Lezcano)
- Delete the thermal driver for Intel Menlow platforms that is not
expected to have any users (Rafael Wysocki)"
* tag 'thermal-6.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: menlow: Get rid of this driver
ACPI: thermal: Move to dedicated function sysfs extra attr creation
ACPI: thermal: Use thermal_zone_device()
thermal: intel: pch_thermal: Use thermal driver device to write a trace
thermal: core: Encapsulate tz->device field
thermal: gov_step_wise: Adjust code logic to match comment
thermal: gov_step_wise: Delete obsolete comment
dt-bindings: thermal: qcom-tsens: Correct unit address
thermal/drivers/mediatek: Use of_address_to_resource()
thermal/drivers/mediatek: Change clk_prepare_enable to devm_clk_get_enabled in mtk_thermal_probe
thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe
thermal/drivers/mediatek: Add temperature constraints to validate read
Revert "thermal/drivers/mediatek: Add delay after thermal banks initialization"
thermal/drivers/cpuidle_cooling: Delete unmatched comments
dt-bindings: thermal: Use generic ADC node name in examples
dt-bindings: imx-thermal: Add imx6sll and imx6ul compatible
The bulk of this is trivial conversions to the new .remove_new()
callback for drivers as part of Uwe's effort to clean that up.
Other than that a driver is added for Apple devices and various small
fixes are included for existing drivers.
Last but not least, this finally gets rid of the old pwm_request() and
pwm_free() APIs are removed since the last user was dropped in v6.3.
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmRSgJcZHHRoaWVycnku
cmVkaW5nQGdtYWlsLmNvbQAKCRDdI6zXfz6zoUZzEACcLaLRRvAsgsrrnunQ1sNT
y5Haep7FjYF8W0cn3MJbH4efdtW6mKJxMV7ZCvbPYXi79Q//4J3oeXV/miRcYTLf
OqALvWKlaXJ3bbwddOdsxjqBBRDPfo3hMTZjSkfiTTbH1vIx3lD/nAdogrVHPBh+
Ap6RMFqb5xnJtefxWNaQ6puWY6XjA9jznitQtMMEkjZqjQtqNd+QX149tFU3avwo
0S4cjUB3FKiSctUXW5EZh3jNSDgB/TYmeslkpmnozkde9DK3ooYMRDMkV0jTaGSb
EKPLWmLSoIDH+ghG7r5KGkE7x5mBELtBbW/KxXBFpro/x528VxYdTgAGOn54XWmn
NcsWiMdReWmPbPDQzZcUBDn8boxyw4jtqsdwzu96G1KHdKcVH6EH00XcH+Pi9KG9
HqPBMvqAjxAn3GK6SdfjGU1KmGB3MYCi4u+twAyycDOEMkxA+FzHSs+OD1a2iaK/
AIYXMjZ4KdVIvIIjJzJttdkTOzt/R6xfn4okvlBzQpD34c7eyi6U+S24+I4yX4y5
wGmZ52h5VvWaBXPaDPYaziyhfRn0nzBSVRXqV62jAusON/xcU6tc1L5YYX0GRNfv
NG264HBAdlUVERs6XDqC+meKwFSzLEmt47pWCBCnOfck/KXLqdsM2tQtMTmI0p4l
9vncNSofIexg/HcrdOFbug==
=slCK
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The bulk of this is trivial conversions to the new .remove_new()
callback for drivers as part of Uwe's effort to clean that up.
Other than that a driver is added for Apple devices and various small
fixes are included for existing drivers.
Last but not least, this finally gets rid of the old pwm_request() and
pwm_free() APIs are removed since the last user was dropped in v6.3"
* tag 'pwm/for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
pwm: Remove unused radix tree
pwm: Delete deprecated functions pwm_request() and pwm_free()
pwm: meson: Fix g12a ao clk81 name
pwm: meson: Fix axg ao mux parents
pwm: stm32: Enforce settings for PWM capture
MAINTAINERS: Add entries for Apple PWM driver
pwm: Add Apple PWM controller
dt-bindings: pwm: Add Apple PWM controller
pwm: mtk-disp: Configure double buffering before reading in .get_state()
pwm: mtk-disp: Disable shadow registers before setting backlight values
pwm: stm32-lp: Drop of_match_ptr for ID table
pwm: rcar: Drop of_match_ptr for ID table
dt-bindings: pwm: Convert Amlogic Meson PWM binding
dt-bindings: pwm: mediatek: Add mediatek,mt7986 compatible
pwm: xilinx: Convert to platform remove callback returning void
pwm: vt8500: Convert to platform remove callback returning void
pwm: tiehrpwm: Convert to platform remove callback returning void
pwm: tiecap: Convert to platform remove callback returning void
pwm: tegra: Convert to platform remove callback returning void
pwm: sun4i: Convert to platform remove callback returning void
...
- New support:
- UFS PHY for Qualcomm SA8775p, SM7150
- PCIe 2 lane phy support for sc8180x and PCIe PHY for SDX65
- Mediatke hdmi phy support for mt8195
- rockchip naneng combo phy support for RK358
- Updates:
- Drop Thunder Bay eMMC PHY driver
- RC support for PCIe phy for Qualcomm SDX55
- SGMII support in WIZ driver for J721E
- PCIe and multilink SGMII PHY support in cadence driver
- Big pile of platform remove callback returning void conversions
-----BEGIN PGP SIGNATURE-----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=WwgW
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New support:
- UFS PHY for Qualcomm SA8775p, SM7150
- PCIe 2 lane phy support for sc8180x and PCIe PHY for SDX65
- Mediatke hdmi phy support for mt8195
- rockchip naneng combo phy support for RK358
Updates:
- Drop Thunder Bay eMMC PHY driver
- RC support for PCIe phy for Qualcomm SDX55
- SGMII support in WIZ driver for J721E
- PCIe and multilink SGMII PHY support in cadence driver
- Big pile of platform remove callback returning void conversions"
* tag 'phy-for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (77 commits)
phy: cadence: cdns-dphy-rx: Add common module reset support
phy: ti: j721e-wiz: Add SGMII support in WIZ driver for J721E
dt-bindings: phy: ti: phy-gmii-sel: Add support for J784S4 CPSW9G
phy: ti: j721e-wiz: Fix unreachable code in wiz_mode_select()
phy: cadence: Sierra: Add PCIe + SGMII PHY multilink configuration
phy: mediatek: add support for phy-mtk-hdmi-mt8195
phy: phy-mtk-hdmi: Add generic phy configure callback
dt-bindings: phy: mediatek: hdmi-phy: Add mt8195 compatible
phy: tegra: xusb: Add missing tegra_xusb_port_unregister for usb2_port and ulpi_port
dt-bindings: phy: ti,phy-j721e-wiz: document clock-output-names
dt-bindings: phy: ti,phy-j721e-wiz: drop assigned-clocks
dt-bindings: phy: ti,phy-am654-serdes: drop assigned-clocks type
dt-bindings: phy: cadence-torrent: drop assigned-clocks
dt-bindings: phy: cadence-sierra: drop assigned-clocks
phy: rockchip: remove unused hw_to_inno function
phy: qualcomm: phy-qcom-qmp-ufs: add definitions for sa8775p
dt-bindings: phy: qmp-ufs: describe the UFS PHY for sa8775p
phy: qcom-qmp-pcie: drop sdm845_qhp_pcie_rx_tbl
phy: qcom-qmp-pcie: sc8180x PCIe PHY has 2 lanes
phy: qcom-qmp-ufs: Add SM7150 support
...
New support:
- Apple admac t8112 device support
- StarFive JH7110 DMA controller
Updates:
- Big pile of idxd updates to support IAA 2.0 device capabilities, DSA
2.0 Event Log and completion record faulting features and new DSA
operations
- at_xdmac supend & resume updates and driver code cleanup
- k3-udma supend & resume support
- k3-psil thread support for J784s4
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAmRSOJYACgkQfBQHDyUj
g0fmUQ//ZmrcNgbubI8evje8oovapLZUqdCgxoq9RbUbJ0TA6y7QCZ4ebkQYQymA
LCJSV+NpG3++gLXLmIoYWiWXCabHZWDPh5M+uUiRm51MV2AtKeHy7UzQolmOWb6E
d4JYf4HdGvzto7nMM7zo/PDaEDKdkostJNb7ZFYZrRqqCbSSSTJYmNGg3PfYRfaw
yJpQsOjizgboM8EciKbqLh9gX3+FfQGhKsnkaiGQBwtdZD29LHeC7UoQrslkH9uh
EiGTMYPKCZIAb+75G4WSO3sCNZcShQPEQt8w3SBP9X6eyaH75AZPymSRhF6O8gte
ecGW/mRzc7t8lOrRnzD1zvZ/4NgwlnxTQAl+561XwWjmZIW/Zd9dH8dHFzwS5alS
z7uVperSYXoEo//UmmwuhuZXlOWD4muOswWB4I5lTeHW97OUyccU5S3DhxYnffI6
P8qnGMmxLj8nsmk98T8TsOmzdb5txxSbPP+PumvDVF7g9LoFKfz8wDAZG3buTsJP
L/HR9sAFaFO0GrjoC7EsHJsiLauSzzcDnYIUJ5UIv/6Ogf2mUCrBhgwSmVhIeR26
hUzYAdpwmhrrVXtbMXuec7jAz62bqkACdJIWGd21t/FTzUNUaDv5OimiNEZncpnY
9q2cT9x94iHHVCl430jlIAOa/oF2AQpeqs4any7+OI2xwiJEA7g=
=Vqrw
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- Apple admac t8112 device support
- StarFive JH7110 DMA controller
Updates:
- Big pile of idxd updates to support IAA 2.0 device capabilities,
DSA 2.0 Event Log and completion record faulting features and
new DSA operations
- at_xdmac supend & resume updates and driver code cleanup
- k3-udma supend & resume support
- k3-psil thread support for J784s4"
* tag 'dmaengine-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (57 commits)
dmaengine: idxd: add per wq PRS disable
dmaengine: idxd: add pid to exported sysfs attribute for opened file
dmaengine: idxd: expose fault counters to sysfs
dmaengine: idxd: add a device to represent the file opened
dmaengine: idxd: add per file user counters for completion record faults
dmaengine: idxd: process batch descriptor completion record faults
dmaengine: idxd: add descs_completed field for completion record
dmaengine: idxd: process user page faults for completion record
dmaengine: idxd: add idxd_copy_cr() to copy user completion record during page fault handling
dmaengine: idxd: create kmem cache for event log fault items
dmaengine: idxd: add per DSA wq workqueue for processing cr faults
dmanegine: idxd: add debugfs for event log dump
dmaengine: idxd: add interrupt handling for event log
dmaengine: idxd: setup event log configuration
dmaengine: idxd: add event log size sysfs attribute
dmaengine: idxd: make misc interrupt one shot
dt-bindings: dma: snps,dw-axi-dmac: constrain the items of resets for JH7110 dma
dt-bindings: dma: Drop unneeded quotes
dmaengine: at_xdmac: align declaration of ret with the rest of variables
dmaengine: at_xdmac: add a warning message regarding for unpaused channels
...
The changes for the hte/timestamp subsystem include the following:
- Add Tegra234 HTE provider and relevant DT bindings
- Update MAINTAINERS file for the HTE subsystem
-----BEGIN PGP SIGNATURE-----
iIgEABYIADAWIQT4slW2T0Q/rXAa29f4pUxhzZTZKAUCZErbLBIcZGlwZW5wQG52
aWRpYS5jb20ACgkQ+KVMYc2U2SiW0QEAt3bPgopjIMzaInOguZthR1pHCuKtyK7F
u4aJAyHv7tIA/jtsFJuFO4LmiwA/IsNits5l7F36oaB94/cQGuRH1M8E
=opcL
-----END PGP SIGNATURE-----
Merge tag 'for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pateldipen1984/linux
Pull hardware timestamp engine updates from Dipen Patel:
"The changes for the hte subsystem include:
- Add Tegra234 HTE provider and relevant DT bindings
- Update MAINTAINERS file for the HTE subsystem"
* tag 'for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pateldipen1984/linux:
hte: tegra-194: Use proper includes
hte: Use device_match_of_node()
hte: tegra-194: Fix off by one in tegra_hte_map_to_line_id()
hte: tegra: fix 'struct of_device_id' build error
hte: Use of_property_present() for testing DT property presence
gpio: tegra186: Add Tegra234 hte support
hte: handle nvidia,gpio-controller property
hte: Deprecate nvidia,slices property
hte: Add Tegra234 provider
hte: Re-phrase tegra API document
arm64: tegra: Add Tegra234 GTE nodes
dt-bindings: timestamp: Deprecate nvidia,slices property
dt-bindings: timestamp: Add Tegra234 support
MAINTAINERS: Add HTE/timestamp subsystem details
Dave Hansen found the "(long) addr >= 0" code in the x86-64 access_ok
checks somewhat confusing, and suggested using a helper to clarify what
the code is doing.
So this does exactly that: clarifying what the sign bit check is all
about, by adding a helper macro that makes it clear what it is testing.
This also adds some explicit comments talking about how even with LAM
enabled, any addresses with the sign bit will still GP-fault in the
non-canonical region just above the sign bit.
This is all what allows us to do the user address checks with just the
sign bit, and furthermore be a bit cavalier about accesses that might be
done with an additional offset even past that point.
(And yes, this talks about 'positive' even though zero is also a valid
user address and so technically we should call them 'non-negative'. But
I don't think using 'non-negative' ends up being more understandable).
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intent of the sign games was to not modify kernel addresses when
untagging them. However, that had two issues:
(a) it didn't actually work as intended, since the mask was calculated
as 'addr >> 63' on an _unsigned_ address. So instead of getting a
mask of all ones for kernel addresses, you just got '1'.
(b) untagging a kernel address isn't actually a valid operation anyway.
Now, (a) had originally been true for both 'untagged_addr()' and the
remote version of it, but had accidentally been fixed for the regular
version of untagged_addr() by commit e0bddc19ba ("x86/mm: Reduce
untagged_addr() overhead for systems without LAM"). That one rewrote
the shift to be part of the alternative asm code, and in the process
changed the unsigned shift into a signed 'sar' instruction.
And while it is true that we don't want to turn what looks like a kernel
address into a user address by masking off the high bit, that doesn't
need these sign masking games - all it needs is that the mm context
'untag_mask' value has the high bit set.
Which it always does.
So simplify the code by just removing the superfluous (and in the case
of untagged_addr_remote(), still buggy) sign bit games in the address
masking.
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The x86 <asm/uaccess.h> file has grown features that are specific to
x86-64 like LAM support and the related access_ok() changes. They
really should be in the <asm/uaccess_64.h> file and not pollute the
generic x86 header.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's already a generic definition of 'access_ok()' in the
asm-generic/access_ok.h header file, and the only difference bwteen that
and the x86-specific one is the added check for WARN_ON_IN_IRQ().
And it turns out that the reason for that check is long gone: it used to
use a "user_addr_max()" inline function that depended on the current
thread, and caused problems in non-thread contexts.
For details, see commits 7c4788950b ("x86/uaccess, sched/preempt:
Verify access_ok() context") and in particular commit ae31fe51a3
("perf/x86: Restore TASK_SIZE check on frame pointer") about how and why
this came to be.
But that "current task" issue was removed in the big set_fs() removal by
Christoph Hellwig in commit 47058bb54b ("x86: remove address space
overrides using set_fs()").
So the reason for the test and the architecture-specific access_ok()
define no longer exists, and is actually harmful these days. For
example, it led various 'copy_from_user_nmi()' games (eg using
__range_not_ok() instead, and then later converted to __access_ok() when
that became ok).
And that in turn meant that LAM was broken for the frame following
before this series, because __access_ok() used to not do the address
untagging.
Accessing user state still needs care in many contexts, but access_ok()
is not the place for this test.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds torvalds@linux-foundation.org>
The linear address masking (LAM) code made access_ok() more complicated,
in that it now needs to untag the address in order to verify the access
range. See commit 74c228d20a ("x86/uaccess: Provide untagged_addr()
and remove tags before address check").
We were able to avoid that overhead in the get_user/put_user code paths
by simply using the sign bit for the address check, and depending on the
GP fault if the address was non-canonical, which made it all independent
of LAM.
And we can do the same thing for access_ok(): simply check that the user
pointer range has the high bit clear. No need to bother with any
address bit masking.
In fact, we can go a bit further, and just check the starting address
for known small accesses ranges: any accesses that overflow will still
be in the non-canonical area and will still GP fault.
To still make syzkaller catch any potentially unchecked user addresses,
we'll continue to warn about GP faults that are caused by accesses in
the non-canonical range. But we'll limit that to purely "high bit set
and past the one-page 'slop' area".
We could probably just do that "check only starting address" for any
arbitrary range size: realistically all kernel accesses to user space
will be done starting at the low address. But let's leave that kind of
optimization for later. As it is, this already allows us to generate
simpler code and not worry about any tag bits in the address.
The one thing to look out for is the GUP address check: instead of
actually copying data in the virtual address range (and thus bad
addresses being caught by the GP fault), GUP will look up the page
tables manually. As a result, the page table limits need to be checked,
and that was previously implicitly done by the access_ok().
With the relaxed access_ok() check, we need to just do an explicit check
for TASK_SIZE_MAX in the GUP code instead. The GUP code already needs
to do the tag bit unmasking anyway, so there this is all very
straightforward, and there are no LAM issues.
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This file defines both read and write operations, yet it is being
created as read-only. This means that it can't be written to without the
CAP_DAC_OVERRIDE capability. Fix the permissions to allow root to write
to it without the need to override DAC perms.
Link: https://lore.kernel.org/linux-trace-kernel/20230503140114.3280002-1-omosnace@redhat.com
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: 03329f9939 ("tracing: Add tracefs file buffer_percentage")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Fix the argument pointer (ap) to point to real-mode memory
instead of virtual memory.
It's interesting that this issue hasn't shown up earlier, as this could
have happened with any 64-bit PDC ROM code.
I just noticed it because I suddenly faced a HPMC while trying to execute
the 64-bit STI ROM code of an Visualize-FXe graphics card for the STI
text console.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
This change simplifies the randomization of file mapping regions. It
reworks the code to remove duplication. The flow is now similar to
that for mips. Finally, we consistently use the do_color_align variable
to determine when color alignment is needed.
Tested on rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Matthew Wilcox noticed, that if ARCH_HAS_FLUSH_ON_KUNMAP is defined
(which is the case for PA-RISC), __kunmap_local() calls
kunmap_flush_on_unmap(), which may call the parisc flush functions with
a non-page-aligned address and thus the page might not be fully flushed.
This patch ensures that flush_kernel_dcache_page_asm() and
flush_kernel_dcache_page_asm() will always operate on page-aligned
addresses.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v6.0+
The panic notifiers' callbacks execute in an atomic context, with
interrupts/preemption disabled, and all CPUs not running the panic
function are off, so it's very dangerous to wait on a regular
spinlock, there's a risk of deadlock.
Refactor the panic notifier of parisc/power driver to make use
of spin_trylock - for that, we've added a second version of the
soft-power function. Also, some comments were reorganized and
trailing white spaces, useless header inclusion and blank lines
were removed.
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jeroen Roovers <jer@xs4all.nl>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Helge Deller <deller@gmx.de>
ARCH=parisc64 is now supported for 64-bit parisc builds, so add
this alias to the kbuild.rst documentation.
Fixes: 3dcfb729b5 ("parisc: Make CONFIG_64BIT available for ARCH=parisc64 only")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: linux-kbuild@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Acked-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Changes during conversion:
- add used, but previously undocumented SoC-specific compatibles
- drop references to SoCs that are not upstream
- add supported clock frequencies
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The gxp_i2c_slave_irq_handler() is hidden in an #ifdef, but the
caller uses an IS_ENABLED() check:
drivers/i2c/busses/i2c-gxp.c: In function 'gxp_i2c_irq_handler':
drivers/i2c/busses/i2c-gxp.c:467:29: error: implicit declaration of function 'gxp_i2c_slave_irq_handler'; did you mean 'gxp_i2c_irq_handler'? [-Werror=implicit-function-declaration]
It has to consistently use one method or the other to avoid warnings,
so move to IS_ENABLED() here for readability and build coverage, and
move the #ifdef in linux/i2c.h to allow building it as dead code.
Fixes: 4a55ed6f89 ("i2c: Add GXP SoC I2C Controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This is unsafe, as the runtime PM callbacks are called from the PM
workqueue, so this may deadlock when handling an i2c attached clock,
which may already hold the clk_prepare mutex from another context.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using standard mode, rare false ACK responses were appearing with
i2cdetect tool. This was happening due to NACK interrupt triggering
ISR thread before register access interrupt was ready. Removing the
NACK interrupt's ability to trigger ISR thread lets register access
ready interrupt do this instead.
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 3b2f8f82da ("i2c: omap: switch to threaded IRQ support")
Signed-off-by: Reid Tonking <reidt@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Merge hibernation test mode fix for 6.4-rc1.
* pm-sleep:
PM: hibernate: Do not get block device exclusively in test_resume mode
PM: hibernate: Turn snapshot_test into global variable
Merge an ACPI power management quirk and a change related to the
handling of ACPI device properties for 6.4-rc1:
- Do not turn off unused power resources during initialization on the
Toshiba Click Mini (Hans de Goede).
- Support strings in device properties supplied by ACPI _DSM on Apple
platforms (Hector Martin).
* acpi-pm:
ACPI: PM: Do not turn of unused power resources on the Toshiba Click Mini
* acpi-properties:
ACPI: property: Support strings in Apple _DSM props
Merge additional thermal core and ACPI thermal changes for 6.4-rc1:
- Clean up the step-wise thermal governor (Zhang Rui).
- Introduce thermal_zone_device() for accessing the device field of
struct thermal_zone_device and two drivers use it (Daniel Lezcano).
- Clean up the ACPI thermal driver a bit (Daniel Lezcano).
- Delete the thermal driver for Intel Menlow platforms that is not
expected to have any users (Rafael Wysocki).
* thermal-core:
thermal: intel: menlow: Get rid of this driver
ACPI: thermal: Move to dedicated function sysfs extra attr creation
ACPI: thermal: Use thermal_zone_device()
thermal: intel: pch_thermal: Use thermal driver device to write a trace
thermal: core: Encapsulate tz->device field
thermal: gov_step_wise: Adjust code logic to match comment
thermal: gov_step_wise: Delete obsolete comment
"ct untracked" no longer works properly due to erroneous NFT_BREAK.
We have to check ctinfo enum first.
Fixes: d9e7891476 ("netfilter: nf_tables: avoid retpoline overhead for some ct expression calls")
Reported-by: Rvfg <i@rvf6.com>
Link: https://marc.info/?l=netfilter&m=168294996212038&w=2
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
igc_configure_rx_ring() function will be called as part of XDP program
setup. If Rx hardware timestamp is enabled prio to XDP program setup,
this timestamp enablement will be overwritten when buffer size is
written into SRRCTL register.
Thus, this commit read the register value before write to SRRCTL
register. This commit is tested by using xdp_hw_metadata bpf selftest
tool. The tool enables Rx hardware timestamp and then attach XDP program
to igc driver. It will display hardware timestamp of UDP packet with
port number 9092. Below are detail of test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
Command on Link Partner:
echo -n skb | nc -u -q1 <destination IPv4 addr> 9092
Result before this patch:
skb hwtstamp is not found!
Result after this patch:
found skb hwtstamp = 1677800973.642836757
Optionally, read PHC to confirm the values obtained are almost the same:
Command:
sudo ./testptp -d /dev/ptp0 -g
Result:
clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add selecting of AUXILIARY_BUS and NET_DEVLINK to the pds_core
Kconfig.
Link: https://lore.kernel.org/netdev/ZE%2FduNH3lBLreNkJ@corigine.com/
Fixes: ddbcb22055 ("pds_core: Kconfig and pds_core.rst")
Suggested-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cruft from previous drafts should have been removed when
the code was updated to not use the old style dummy helpers.
Fixes: 55435ea772 ("pds_core: initial framework for pds_core PF driver")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check for NULL on the alloc return. If devlink_alloc() fails and
we try to use devlink_priv() on the NULL return, the kernel gets very
unhappy and panics. With this fix, the driver load will still fail,
but at least it won't panic the kernel.
Fixes: df69ba4321 ("ionic: Add basic framework for IONIC Network device driver")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not possible to set the number of lanes when setting link modes
using the legacy IOCTL ethtool interface. Since 'struct
ethtool_link_ksettings' is not initialized in this path, drivers receive
an uninitialized number of lanes in 'struct
ethtool_link_ksettings::lanes'.
When this information is later queried from drivers, it results in the
ethtool code making decisions based on uninitialized memory, leading to
the following KMSAN splat [1]. In practice, this most likely only
happens with the tun driver that simply returns whatever it got in the
set operation.
As far as I can tell, this uninitialized memory is not leaked to user
space thanks to the 'ethtool_ops->cap_link_lanes_supported' check in
linkmodes_prepare_data().
Fix by initializing the structure in the IOCTL path. Did not find any
more call sites that pass an uninitialized structure when calling
'ethtool_ops::set_link_ksettings()'.
[1]
BUG: KMSAN: uninit-value in ethnl_update_linkmodes net/ethtool/linkmodes.c:273 [inline]
BUG: KMSAN: uninit-value in ethnl_set_linkmodes+0x190b/0x19d0 net/ethtool/linkmodes.c:333
ethnl_update_linkmodes net/ethtool/linkmodes.c:273 [inline]
ethnl_set_linkmodes+0x190b/0x19d0 net/ethtool/linkmodes.c:333
ethnl_default_set_doit+0x88d/0xde0 net/ethtool/netlink.c:640
genl_family_rcv_msg_doit net/netlink/genetlink.c:968 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline]
genl_rcv_msg+0x141a/0x14c0 net/netlink/genetlink.c:1065
netlink_rcv_skb+0x3f8/0x750 net/netlink/af_netlink.c:2577
genl_rcv+0x40/0x60 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0xf41/0x1270 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x127d/0x1430 net/netlink/af_netlink.c:1942
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0xa24/0xe40 net/socket.c:2501
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2555
__sys_sendmsg net/socket.c:2584 [inline]
__do_sys_sendmsg net/socket.c:2593 [inline]
__se_sys_sendmsg net/socket.c:2591 [inline]
__x64_sys_sendmsg+0x36b/0x540 net/socket.c:2591
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was stored to memory at:
tun_get_link_ksettings+0x37/0x60 drivers/net/tun.c:3544
__ethtool_get_link_ksettings+0x17b/0x260 net/ethtool/ioctl.c:441
ethnl_set_linkmodes+0xee/0x19d0 net/ethtool/linkmodes.c:327
ethnl_default_set_doit+0x88d/0xde0 net/ethtool/netlink.c:640
genl_family_rcv_msg_doit net/netlink/genetlink.c:968 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline]
genl_rcv_msg+0x141a/0x14c0 net/netlink/genetlink.c:1065
netlink_rcv_skb+0x3f8/0x750 net/netlink/af_netlink.c:2577
genl_rcv+0x40/0x60 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0xf41/0x1270 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x127d/0x1430 net/netlink/af_netlink.c:1942
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0xa24/0xe40 net/socket.c:2501
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2555
__sys_sendmsg net/socket.c:2584 [inline]
__do_sys_sendmsg net/socket.c:2593 [inline]
__se_sys_sendmsg net/socket.c:2591 [inline]
__x64_sys_sendmsg+0x36b/0x540 net/socket.c:2591
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was stored to memory at:
tun_set_link_ksettings+0x37/0x60 drivers/net/tun.c:3553
ethtool_set_link_ksettings+0x600/0x690 net/ethtool/ioctl.c:609
__dev_ethtool net/ethtool/ioctl.c:3024 [inline]
dev_ethtool+0x1db9/0x2a70 net/ethtool/ioctl.c:3078
dev_ioctl+0xb07/0x1270 net/core/dev_ioctl.c:524
sock_do_ioctl+0x295/0x540 net/socket.c:1213
sock_ioctl+0x729/0xd90 net/socket.c:1316
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl+0x222/0x400 fs/ioctl.c:856
__x64_sys_ioctl+0x96/0xe0 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Local variable link_ksettings created at:
ethtool_set_link_ksettings+0x54/0x690 net/ethtool/ioctl.c:577
__dev_ethtool net/ethtool/ioctl.c:3024 [inline]
dev_ethtool+0x1db9/0x2a70 net/ethtool/ioctl.c:3078
Fixes: 012ce4dd31 ("ethtool: Extend link modes settings uAPI with lanes")
Reported-and-tested-by: syzbot+ef6edd9f1baaa54d6235@syzkaller.appspotmail.com
Link: https://lore.kernel.org/netdev/0000000000004bb41105fa70f361@google.com/
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set supports_autosuspend = 1 for the rtl8152_cfgselector_driver.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that ethtool is calling into .get_rxnfc more often with
ETHTOOL_GRXCLSRLCNT which ionic doesn't know about. We don't
need to log a message about it, just return not supported.
Fixes: aa3198819b ("ionic: Add RSS support")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sai Krishna says:
====================
octeontx2: Miscellaneous fixes
This patchset includes following fixes.
Patch #1 Fix for the race condition while updating APR table
Patch #2 Fix end bit position in NPC scan config
Patch #3 Fix depth of CAM, MEM table entries
Patch #4 Fix in increase the size of DMAC filter flows
Patch #5 Fix driver crash resulting from invalid interface type
information retrieved from firmware
Patch #6 Fix incorrect mask used while installing filters involving
fragmented packets
Patch #7 Fixes for NPC field hash extract w.r.t IPV6 hash reduction,
IPV6 filed hash configuration.
Patch #8 Fix for NPC hardware parser configuration destination
address hash, IPV6 endianness issues.
Patch #9 Fix for skipping mbox initialization for PFs disabled by firmware.
Patch #10 Fix disabling packet I/O in case of mailbox timeout.
Patch #11 Fix detaching LF resources in case of VF probe fail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF device probe fails due to error in MSIX vector allocation then
the resources NIX and NPA LFs were not detached. Fix this by detaching
the LFs when MSIX vector allocation fails.
Fixes: 3184fb5ba9 ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the stage of enabling packet I/O in otx2_open, If mailbox
timeout occurs then interface ends up in down state where as
hardware packet I/O is enabled. Hence disable packet I/O also
before bailing out.
Fixes: 1ea0166da0 ("octeontx2-pf: Fix the device state on error")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware enables PFs and allocate mbox resources for each of the PFs.
Currently PF driver configures mbox resources without checking whether
PF is enabled or not. This results in crash. This patch fixes this issue
by skipping disabled PF's mbox initialization.
Fixes: 9bdc47a6e3 ("octeontx2-af: Mbox communication support btw AF and it's VFs")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Allow field hash configuration for both source and destination IPv6.
2. Configure hardware parser based on hash extract feature enable flag
for IPv6.
3. Fix IPv6 endianness issue while updating the source/destination IP
address via ntuple rule.
Fixes: 56d9f5fd22 ("octeontx2-af: Use hashed field in MCAM key")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. As per previous implementation, mask and control parameter to
generate the field hash value was not passed to the caller program.
Updated the secret key mbox to share that information as well,
as a part of the fix.
2. Earlier implementation did not consider hash reduction of both
source and destination IPv6 addresses. Only source IPv6 address
was considered. This fix solves that and provides option to hash
Fixes: 56d9f5fd22 ("octeontx2-af: Use hashed field in MCAM key")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the initial design, the IPv4 ip_flag mask was set to 0xff.
Which results to filter only fragmets with (fragment_offset == 0).
As part of the fix, updated the mask to 0x20 to filter all the
fragmented packets irrespective of the fragment_offset value.
Fixes: c672e37279 ("octeontx2-pf: Add support to filter packet based on IP fragment")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon physical link change, firmware reports to the kernel about the
change along with the details like speed, lmac_type_id, etc.
Kernel derives lmac_type based on lmac_type_id received from firmware.
In a few scenarios, firmware returns an invalid lmac_type_id, which
is resulting in below kernel panic. This patch adds the missing
validation of the lmac_type_id field.
Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 35.321595] Modules linked in:
[ 35.328982] CPU: 0 PID: 31 Comm: kworker/0:1 Not tainted
5.4.210-g2e3169d8e1bc-dirty #17
[ 35.337014] Hardware name: Marvell CN103XX board (DT)
[ 35.344297] Workqueue: events work_for_cpu_fn
[ 35.352730] pstate: 40400089 (nZcv daIf +PAN -UAO)
[ 35.360267] pc : strncpy+0x10/0x30
[ 35.366595] lr : cgx_link_change_handler+0x90/0x180
Fixes: 61071a871e ("octeontx2-af: Forward CGX link notifications to PFs")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10kb supports large number of dmac filter flows to be
inserted. Increase the field size to accommodate the same
Fixes: b747923aff ("octeontx2-af: Exact match support")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current driver, NPC cam and mem table sizes are read from wrong
register offset. This patch fixes the register offset so that correct
values are populated on read.
Fixes: b747923aff ("octeontx2-af: Exact match support")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, NPC exact match feature was not getting
enabled as configured bit was not read properly.
for_each_set_bit_from() need end bit as one bit post
position in the bit map to read NPC exact nibble enable
bits properly. This patch fixes the same.
Fixes: b747923aff ("octeontx2-af: Exact match support")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
APR table contains the lmtst base address of PF/VFs. These entries
are updated by the PF/VF during the device probe. The lmtst address
is fetched from HW using "TXN_REQ" and "ADDR_RSP_STS" registers.
The lock tries to protect these registers from getting overwritten
when multiple PFs invokes rvu_get_lmtaddr() simultaneously.
For example, if PF1 submit the request and got permitted before it
reads the response and PF2 got scheduled submit the request then the
response of PF1 is overwritten by the PF2 response.
Fixes: 893ae97214 ("octeontx2-af: cn10k: Support configurable LMTST regions")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
