When innerprotoinherit is set, the tunneled packets do not have an inner
Ethernet header.
Change 'maclen' to not always assume the header length is ETH_HLEN, as
there might not be a MAC header.
This resolves issues with drivers (e.g. mlx5, in
mlx5e_tx_tunnel_accel()) who rely on the skb inner network header offset
to be correct, and use it for TX offloads.
Fixes: d8a6213d70 ("geneve: fix header validation in geneve[6]_xmit_skb")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot is able to trigger an uninit-value in geneve_xmit() [1]
Problem : While most ip tunnel helpers (like ip_tunnel_get_dsfield())
uses skb_protocol(skb, true), pskb_inet_may_pull() is only using
skb->protocol.
If anything else than ETH_P_IPV6 or ETH_P_IP is found in skb->protocol,
pskb_inet_may_pull() does nothing at all.
If a vlan tag was provided by the caller (af_packet in the syzbot case),
the network header might not point to the correct location, and skb
linear part could be smaller than expected.
Add skb_vlan_inet_prepare() to perform a complete mac validation.
Use this in geneve for the moment, I suspect we need to adopt this
more broadly.
v4 - Jakub reported v3 broke l2_tos_ttl_inherit.sh selftest
- Only call __vlan_get_protocol() for vlan types.
Link: https://lore.kernel.org/netdev/20240404100035.3270a7d5@kernel.org/
v2,v3 - Addressed Sabrina comments on v1 and v2
Link: https://lore.kernel.org/netdev/Zg1l9L2BNoZWZDZG@hog/
[1]
BUG: KMSAN: uninit-value in geneve_xmit_skb drivers/net/geneve.c:910 [inline]
BUG: KMSAN: uninit-value in geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030
geneve_xmit_skb drivers/net/geneve.c:910 [inline]
geneve_xmit+0x302d/0x5420 drivers/net/geneve.c:1030
__netdev_start_xmit include/linux/netdevice.h:4903 [inline]
netdev_start_xmit include/linux/netdevice.h:4917 [inline]
xmit_one net/core/dev.c:3531 [inline]
dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547
__dev_queue_xmit+0x348d/0x52c0 net/core/dev.c:4335
dev_queue_xmit include/linux/netdevice.h:3091 [inline]
packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x8bb0/0x9ef0 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x30f/0x380 net/socket.c:745
__sys_sendto+0x685/0x830 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1d0 net/socket.c:2199
do_syscall_64+0xd5/0x1f0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
Uninit was created at:
slab_post_alloc_hook mm/slub.c:3804 [inline]
slab_alloc_node mm/slub.c:3845 [inline]
kmem_cache_alloc_node+0x613/0xc50 mm/slub.c:3888
kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:577
__alloc_skb+0x35b/0x7a0 net/core/skbuff.c:668
alloc_skb include/linux/skbuff.h:1318 [inline]
alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6504
sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2795
packet_alloc_skb net/packet/af_packet.c:2930 [inline]
packet_snd net/packet/af_packet.c:3024 [inline]
packet_sendmsg+0x722d/0x9ef0 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x30f/0x380 net/socket.c:745
__sys_sendto+0x685/0x830 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1d0 net/socket.c:2199
do_syscall_64+0xd5/0x1f0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
CPU: 0 PID: 5033 Comm: syz-executor346 Not tainted 6.9.0-rc1-syzkaller-00005-g928a87efa423 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024
Fixes: d13f048dd4 ("net: geneve: modify IP header check in geneve6_xmit_skb and geneve_xmit_skb")
Reported-by: syzbot+9ee20ec1de7b3168db09@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/000000000000d19c3a06152f9ee4@google.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Phillip Potter <phil@philpotter.co.uk>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically, tunnel flags like TUNNEL_CSUM or TUNNEL_ERSPAN_OPT
have been defined as __be16. Now all of those 16 bits are occupied
and there's no more free space for new flags.
It can't be simply switched to a bigger container with no
adjustments to the values, since it's an explicit Endian storage,
and on LE systems (__be16)0x0001 equals to
(__be64)0x0001000000000000.
We could probably define new 64-bit flags depending on the
Endianness, i.e. (__be64)0x0001 on BE and (__be64)0x00010000... on
LE, but that would introduce an Endianness dependency and spawn a
ton of Sparse warnings. To mitigate them, all of those places which
were adjusted with this change would be touched anyway, so why not
define stuff properly if there's no choice.
Define IP_TUNNEL_*_BIT counterparts as a bit number instead of the
value already coded and a fistful of <16 <-> bitmap> converters and
helpers. The two flags which have a different bit position are
SIT_ISATAP_BIT and VTI_ISVTI_BIT, as they were defined not as
__cpu_to_be16(), but as (__force __be16), i.e. had different
positions on LE and BE. Now they both have strongly defined places.
Change all __be16 fields which were used to store those flags, to
IP_TUNNEL_DECLARE_FLAGS() -> DECLARE_BITMAP(__IP_TUNNEL_FLAG_NUM) ->
unsigned long[1] for now, and replace all TUNNEL_* occurrences to
their bitmap counterparts. Use the converters in the places which talk
to the userspace, hardware (NFP) or other hosts (GRE header). The rest
must explicitly use the new flags only. This must be done at once,
otherwise there will be too many conversions throughout the code in
the intermediate commits.
Finally, disable the old __be16 flags for use in the kernel code
(except for the two 'irregular' flags mentioned above), to prevent
any accidental (mis)use of them. For the userspace, nothing is
changed, only additions were made.
Most noticeable bloat-o-meter difference (.text):
vmlinux: 307/-1 (306)
gre.ko: 62/0 (62)
ip_gre.ko: 941/-217 (724) [*]
ip_tunnel.ko: 390/-900 (-510) [**]
ip_vti.ko: 138/0 (138)
ip6_gre.ko: 534/-18 (516) [*]
ip6_tunnel.ko: 118/-10 (108)
[*] gre_flags_to_tnl_flags() grew, but still is inlined
[**] ip_tunnel_find() got uninlined, hence such decrease
The average code size increase in non-extreme case is 100-200 bytes
per module, mostly due to sizeof(long) > sizeof(__be16), as
%__IP_TUNNEL_FLAG_NUM is less than %BITS_PER_LONG and the compilers
are able to expand the majority of bitmap_*() calls here into direct
operations on scalars.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240305172911.502058-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the geneve driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240305172911.502058-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
skb_gro_header_hard() is renamed to skb_gro_may_pull() to match
the convention used by common helpers like pskb_may_pull().
This means the condition is inverted:
if (skb_gro_header_hard(skb, hlen))
slow_path();
becomes:
if (!skb_gro_may_pull(skb, hlen))
slow_path();
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the geneve_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair,
and one unregister_netdevice_many() call.
Note: it should be possible to remove the synchronize_net()
call from geneve_sock_release() in a future patch.
v4: move WARN_ON_ONCE(!list_empty(&gn->sock_list))
into geneve_exit_net(), after devices have been unregistered.
(Antoine Tenart feedback)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-7-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The route lookup can be done now via generic function
udp_tunnel6_dst_lookup() to replace the custom implementation in
geneve_get_v6_dst().
This is similar to what already done for IPv4 in commit daa2ba7ed1
("geneve: use generic function for tunnel IPv4 route lookup").
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The route lookup can be done now via generic function
udp_tunnel_dst_lookup() to replace the custom implementation in
geneve_get_v4_rt().
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to compute the tos/dsfield. In this way, we can
factor out some duplicate code. Also, the helper will be called from
more places in the next commit.
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Geneve encapsulation, as defined in RFC 8926, has a Protocol Type
field, which states the Ethertype of the payload appearing after the
Geneve header.
Commit 435fe1c0c1 ("net: geneve: support IPv4/IPv6 as inner protocol")
introduced a new IFLA_GENEVE_INNER_PROTO_INHERIT flag that allowed the
use of other Ethertypes than Ethernet. However, it did not get rid of a
restriction that prohibits receiving payloads other than Ethernet,
instead the commit white-listed additional Ethertypes, IPv4 and IPv6.
This patch removes this restriction, making it possible to receive any
Ethertype as a payload, if the IFLA_GENEVE_INNER_PROTO_INHERIT flag is
set.
The restriction was set in place back in commit 0b5e8b8eea
("net: Add Geneve tunneling protocol driver"), which implemented a
protocol layer driver for Geneve to be used with Open vSwitch. The
relevant discussion about introducing the Ethertype white-list can be
found here:
https://lore.kernel.org/netdev/CAEP_g=_1q3ACX5NTHxLDnysL+dTMUVzdLpgw1apLKEdDSWPztw@mail.gmail.com/
<quote>
>> + if (unlikely(geneveh->proto_type != htons(ETH_P_TEB)))
>
> Why? I thought the point of geneve carrying protocol field was to
> allow protocols other than Ethernet... is this temporary maybe?
Yes, it is temporary. Currently OVS only handles Ethernet packets but
this restriction can be lifted once we have a consumer that is capable
of handling other protocols.
</quote>
This white-list was then ported to a generic Geneve netdevice in commit
371bd1061d ("geneve: Consolidate Geneve functionality in single
module."). Preserving the Ethertype white-list at this point made sense,
as the Geneve device could send out only Ethernet payloads anyways.
However, now that the Geneve netdevice supports encapsulating other
payloads with IFLA_GENEVE_INNER_PROTO_INHERIT and we have a consumer
capable of other protocols, it seems appropriate to lift the restriction
and allow any Geneve payload to be received.
Signed-off-by: Josef Miegl <josef@miegl.cz>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20230319220954.21834-1-josef@miegl.cz
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The GENEVE tunnel used with IFLA_GENEVE_INNER_PROTO_INHERIT is
point-to-point, so set IFF_POINTOPOINT to reflect that.
Signed-off-by: Josef Miegl <josef@miegl.cz>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pass netlink message header and portid to rtnl_configure_link()
All the functions in this call chain need to add the parameters so we can
use them in the last call rtnl_notify(), and notify the userspace about
the new link info if NLM_F_ECHO flag is set.
- rtnl_configure_link()
- __dev_notify_flags()
- rtmsg_ifinfo()
- rtmsg_ifinfo_event()
- rtmsg_ifinfo_build_skb()
- rtmsg_ifinfo_send()
- rtnl_notify()
Also move __dev_notify_flags() declaration to net/core/dev.h, as Jakub
suggested.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce a simple helper function to replace a common pattern.
When accessing the GRO header, we fetch the pointer from frag0,
then test its validity and fetch it from the skb when necessary.
This leads to the pattern
skb_gro_header_fast -> skb_gro_header_hard -> skb_gro_header_slow
recurring many times throughout GRO code.
This patch replaces these patterns with a single inlined function
call, improving code readability.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220823071034.GA56142@debian
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
According to Guillaume Nault RT_TOS should never be used for IPv6.
Quote:
RT_TOS() is an old macro used to interprete IPv4 TOS as described in
the obsolete RFC 1349. It's conceptually wrong to use it even in IPv4
code, although, given the current state of the code, most of the
existing calls have no consequence.
But using RT_TOS() in IPv6 code is always a bug: IPv6 never had a "TOS"
field to be interpreted the RFC 1349 way. There's no historical
compatibility to worry about.
Fixes: 3a56f86f1b ("geneve: handle ipv6 priority like ipv4 tos")
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Matthias May <matthias.may@westermo.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current code retrieves the TOS field after the lookup
on the ipv4 routing table. The routing process currently
only allows routing based on the original 3 TOS bits, and
not on the full 6 DSCP bits.
As a result the retrieved TOS is cut to the 3 bits.
However for inheriting purposes the full 6 bits should be used.
Extract the full 6 bits before the route lookup and use
that instead of the cut off 3 TOS bits.
Fixes: e305ac6cf5 ("geneve: Add support to collect tunnel metadata.")
Signed-off-by: Matthias May <matthias.may@westermo.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Link: https://lore.kernel.org/r/20220805190006.8078-1-matthias.may@westermo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new ip_tunnel_key field with the flow flags in the IPv4 route
lookups for the encapsulated packet. This will be used by the
bpf_skb_set_tunnel_key helper in the subsequent commit.
Signed-off-by: Paul Chaignon <paul@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/fcc2e0eea01e8ea465a180126366ec20596ba530.1658759380.git.paul@isovalent.com
In the most common setups, the geneve tunnels use an inner
ethernet encapsulation. In the GRO path, when such condition is
true, we can call directly the relevant GRO helper and avoid
a few indirect calls.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing netlink attribute policy and size calculation.
Also enable strict validation from this new attribute onwards.
Fixes: 435fe1c0c1 ("net: geneve: support IPv4/IPv6 as inner protocol")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220322043954.3042468-1-eyal.birger@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for encapsulating IPv4/IPv6 within GENEVE.
In order to use this, a new IFLA_GENEVE_INNER_PROTO_INHERIT flag needs
to be provided at device creation. This property cannot be changed for
the time being.
In case IP traffic is received on a non-tun device the drop count is
increased.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220316061557.431872-1-eyal.birger@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Dave suggested a while ago (eleven years by now) "Let's make netif_rx()
work in all contexts and get rid of netif_rx_ni()". Eric agreed and
pointed out that modern devices should use netif_receive_skb() to avoid
the overhead.
In the meantime someone added another variant, netif_rx_any_context(),
which behaves as suggested.
netif_rx() must be invoked with disabled bottom halves to ensure that
pending softirqs, which were raised within the function, are handled.
netif_rx_ni() can be invoked only from process context (bottom halves
must be enabled) because the function handles pending softirqs without
checking if bottom halves were disabled or not.
netif_rx_any_context() invokes on the former functions by checking
in_interrupts().
netif_rx() could be taught to handle both cases (disabled and enabled
bottom halves) by simply disabling bottom halves while invoking
netif_rx_internal(). The local_bh_enable() invocation will then invoke
pending softirqs only if the BH-disable counter drops to zero.
Eric is concerned about the overhead of BH-disable+enable especially in
regard to the loopback driver. As critical as this driver is, it will
receive a shortcut to avoid the additional overhead which is not needed.
Add a local_bh_disable() section in netif_rx() to ensure softirqs are
handled if needed.
Provide __netif_rx() which does not disable BH and has a lockdep assert
to ensure that interrupts are disabled. Use this shortcut in the
loopback driver and in drivers/net/*.c.
Make netif_rx_ni() and netif_rx_any_context() invoke netif_rx() so they
can be removed once they are no more users left.
Link: https://lkml.kernel.org/r/20100415.020246.218622820.davem@davemloft.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All gro_complete() handlers are called from napi_gro_complete()
while rcu_read_lock() has been called.
There is no point stacking more rcu_read_lock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All gro_receive() handlers are called from dev_gro_receive()
while rcu_read_lock() has been called.
There is no point stacking more rcu_read_lock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
include/linux/netdevice.h became too big, move gro stuff
into include/net/gro.h
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the header size check in geneve6_xmit_skb and geneve_xmit_skb
to use pskb_inet_may_pull rather than pskb_network_may_pull. This fixes
two kernel selftest failures introduced by the commit introducing the
checks:
IPv4 over geneve6: PMTU exceptions
IPv4 over geneve6: PMTU exceptions - nexthop objects
It does this by correctly accounting for the fact that IPv4 packets may
transit over geneve IPv6 tunnels (and vice versa), and still fixes the
uninit-value bug fixed by the original commit.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: 6628ddfec7 ("net: geneve: check skb is large enough for IPv4/IPv6 header")
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check within geneve_xmit_skb/geneve6_xmit_skb that sk_buff structure
is large enough to include IPv4 or IPv6 header, and reject if not. The
geneve_xmit_skb portion and overall idea was contributed by Eric Dumazet.
Fixes a KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=abe95dc3e3e9667fc23b8d81f29ecad95c6f106f
Suggested-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+2e406a9ac75bb71d4b7a@syzkaller.appspotmail.com
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to the previous commit, let even geneve
passthrou the L4 GRO packets
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is part of a bridge or an Open vSwitch port and a
packet exceed a PMTU estimate, an ICMP reply is sent to the sender. When
using the external mode (collect metadata) the source and destination
addresses are reversed, so that Open vSwitch can match the packet
against an existing (reverse) flow.
But inverting the source and destination addresses in the shared
ip_tunnel_info will make following packets of the flow to use a wrong
destination address (packets will be tunnelled to itself), if the flow
isn't updated. Which happens with Open vSwitch, until the flow times
out.
Fixes this by uncloning the skb's ip_tunnel_info before inverting its
source and destination addresses, so that the modification will only be
made for the PTMU packet, not the following ones.
Fixes: c1a800e88d ("geneve: Support for PMTU discovery on directly bridged links")
Tested-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some protocol HW GSO requires fraglist supported by the device, like
SCTP. Without NETIF_F_FRAGLIST set in the dev features of geneve, it
would have to do SW GSO before the packets enter the driver, even
when the geneve dev and lower dev (like veth) both have the feature
of NETIF_F_GSO_SCTP.
So this patch is to add it for geneve.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
udp_tunnel_nic handles REGISTER and UNREGISTER event, now that all
drivers use that infra we can drop the event handling in the tunnel
drivers.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace ip_tunnel_get_stats64() with the new identical core function
dev_get_tstats64().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
