br_set_lockdep_class() is missing many details.
Use generic netdev_lockdep_set_classes() to not worry anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240212140700.2795436-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_vlan_flush() and nbp_vlan_flush() should use synchronize_net()
instead of syncronize_rcu() to release RTNL sooner.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
exit_batch_rtnl() is called while RTNL is held,
and devices to be unregistered can be queued in the dev_kill_list.
This saves one rtnl_lock()/rtnl_unlock() pair per netns
and one unregister_netdevice_many() call.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-16-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 0a31bd5f2b ("KMEM_CACHE(): simplify slab cache creation")
introduces a new macro.
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240130092536.73623-1-chentao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The original idea of the delay_time check was to not apply multicast
snooping too early when an MLD querier appears. And to instead wait at
least for MLD reports to arrive before switching from flooding to group
based, MLD snooped forwarding, to avoid temporary packet loss.
However in a batman-adv mesh network it was noticed that after 248 days of
uptime 32bit MIPS based devices would start to signal that they had
stopped applying multicast snooping due to missing queriers - even though
they were the elected querier and still sending MLD queries themselves.
While time_is_before_jiffies() generally is safe against jiffies
wrap-arounds, like the code comments in jiffies.h explain, it won't
be able to track a difference larger than ULONG_MAX/2. With a 32bit
large jiffies and one jiffies tick every 10ms (CONFIG_HZ=100) on these MIPS
devices running OpenWrt this would result in a difference larger than
ULONG_MAX/2 after 248 (= 2^32/100/60/60/24/2) days and
time_is_before_jiffies() would then start to return false instead of
true. Leading to multicast snooping not being applied to multicast
packets anymore.
Fix this issue by using a proper timer_list object which won't have this
ULONG_MAX/2 difference limitation.
Fixes: b00589af3b ("bridge: disable snooping if there is no querier")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20240127175033.9640-1-linus.luessing@c0d3.blue
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Same patch as previous one, but for ebtables.
To build a kernel that only supports ebtables-nft, the builtin tables
need to be disabled, i.e.:
CONFIG_BRIDGE_EBT_BROUTE=n
CONFIG_BRIDGE_EBT_T_FILTER=n
CONFIG_BRIDGE_EBT_T_NAT=n
The ebtables specific extensions can then be used nftables'
NFT_COMPAT interface.
Signed-off-by: Florian Westphal <fw@strlen.de>
An skb can be added to a neigh->arp_queue while waiting for an arp
reply. Where original skb's skb->dev can be different to neigh's
neigh->dev. For instance in case of bridging dnated skb from one veth to
another, the skb would be added to a neigh->arp_queue of the bridge.
As skb->dev can be reset back to nf_bridge->physindev and used, and as
there is no explicit mechanism that prevents this physindev from been
freed under us (for instance neigh_flush_dev doesn't cleanup skbs from
different device's neigh queue) we can crash on e.g. this stack:
arp_process
neigh_update
skb = __skb_dequeue(&neigh->arp_queue)
neigh_resolve_output(..., skb)
...
br_nf_dev_xmit
br_nf_pre_routing_finish_bridge_slow
skb->dev = nf_bridge->physindev
br_handle_frame_finish
Let's use plain ifindex instead of net_device link. To peek into the
original net_device we will use dev_get_by_index_rcu(). Thus either we
get device and are safe to use it or we don't get it and drop skb.
Fixes: c4e70a87d9 ("netfilter: bridge: rename br_netfilter.c to br_netfilter_hooks.c")
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It appears that there is a typo in the code where the nlattr array is
being parsed with policy br_cfm_cc_ccm_tx_policy, but the instance is
being accessed via IFLA_BRIDGE_CFM_CC_RDI_INSTANCE, which is associated
with the policy br_cfm_cc_rdi_policy.
This problem was introduced by commit 2be665c394 ("bridge: cfm: Netlink
SET configuration Interface.").
Though it seems like a harmless typo since these two enum owns the exact
same value (1 here), it is quite misleading hence fix it by using the
correct enum IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE here.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement MDB bulk deletion support in the bridge driver, allowing MDB
entries to be deleted in bulk according to provided parameters.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill in bridge's module description.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for MDB get operation by looking up a matching MDB
entry, allocating the skb according to the entry's size and then filling
in the response. The operation is performed under the bridge multicast
lock to ensure that the entry does not change between the time the reply
size is determined and when the reply is filled in.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current name is going to conflict with the upcoming net device
operation for the MDB get operation.
Rename the function to br_mdb_entry_skb_get(). No functional changes
intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, netlink notifications are sent for individual port group
entries and not for the entire MDB entry itself.
Subsequent patches are going to add MDB get support which will require
the bridge driver to reply with an entire MDB entry.
Therefore, as a preparation, factor out an helper to calculate the size
of an individual port group entry. When determining the size of the
reply this helper will be invoked for each port group entry in the MDB
entry.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'MDBA_MDB' and 'MDBA_MDB_ENTRY' nest attributes are not accounted
for when calculating the size of MDB notifications. Add them along with
comments for existing attributes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the bridge driver does not dump MDB entries when multicast
snooping is disabled although the entries are present in the kernel:
# bridge mdb add dev br0 port swp1 grp 239.1.1.1 permanent
# bridge mdb show dev br0
dev br0 port swp1 grp 239.1.1.1 permanent
dev br0 port br0 grp ff02::6a temp
dev br0 port br0 grp ff02::1:ff9d:e61b temp
# ip link set dev br0 type bridge mcast_snooping 0
# bridge mdb show dev br0
# ip link set dev br0 type bridge mcast_snooping 1
# bridge mdb show dev br0
dev br0 port swp1 grp 239.1.1.1 permanent
dev br0 port br0 grp ff02::6a temp
dev br0 port br0 grp ff02::1:ff9d:e61b temp
This behavior differs from other netlink dump interfaces that dump
entries regardless if they are used or not. For example, VLANs are
dumped even when VLAN filtering is disabled:
# ip link set dev br0 type bridge vlan_filtering 0
# bridge vlan show dev swp1
port vlan-id
swp1 1 PVID Egress Untagged
Remove the check and always dump MDB entries:
# bridge mdb add dev br0 port swp1 grp 239.1.1.1 permanent
# bridge mdb show dev br0
dev br0 port swp1 grp 239.1.1.1 permanent
dev br0 port br0 grp ff02::6a temp
dev br0 port br0 grp ff02::1:ffeb:1a4d temp
# ip link set dev br0 type bridge mcast_snooping 0
# bridge mdb show dev br0
dev br0 port swp1 grp 239.1.1.1 permanent
dev br0 port br0 grp ff02::6a temp
dev br0 port br0 grp ff02::1:ffeb:1a4d temp
# ip link set dev br0 type bridge mcast_snooping 1
# bridge mdb show dev br0
dev br0 port swp1 grp 239.1.1.1 permanent
dev br0 port br0 grp ff02::6a temp
dev br0 port br0 grp ff02::1:ffeb:1a4d temp
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_netfilter registers two forward hooks, one for ip and one for arp.
Just use a common function for both and then call the arp/ip helper
as needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
errno is 0 because these hooks are called from prerouting and forward.
There is no socket that the errno would ever be propagated to.
Other netfilter modules (e.g. nf_nat, conntrack, ...) can be converted
in a similar way.
Signed-off-by: Florian Westphal <fw@strlen.de>
Set any new attributes added to br_policy to be parsed strictly, to
prevent userspace from passing garbage.
Signed-off-by: Johannes Nixdorf <jnixdorf-oss@avm.de>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20231016-fdb_limit-v5-4-32cddff87758@avm.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch added accounting and a limit for the number of
dynamically learned FDB entries per bridge. However it did not provide
means to actually configure those bounds or read back the count. This
patch does that.
Two new netlink attributes are added for the accounting and limit of
dynamically learned FDB entries:
- IFLA_BR_FDB_N_LEARNED (RO) for the number of entries accounted for
a single bridge.
- IFLA_BR_FDB_MAX_LEARNED (RW) for the configured limit of entries for
the bridge.
The new attributes are used like this:
# ip link add name br up type bridge fdb_max_learned 256
# ip link add name v1 up master br type veth peer v2
# ip link set up dev v2
# mausezahn -a rand -c 1024 v2
0.01 seconds (90877 packets per second
# bridge fdb | grep -v permanent | wc -l
256
# ip -d link show dev br
13: br: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 [...]
[...] fdb_n_learned 256 fdb_max_learned 256
Signed-off-by: Johannes Nixdorf <jnixdorf-oss@avm.de>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20231016-fdb_limit-v5-3-32cddff87758@avm.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A malicious actor behind one bridge port may spam the kernel with packets
with a random source MAC address, each of which will create an FDB entry,
each of which is a dynamic allocation in the kernel.
There are roughly 2^48 different MAC addresses, further limited by the
rhashtable they are stored in to 2^31. Each entry is of the type struct
net_bridge_fdb_entry, which is currently 128 bytes big. This means the
maximum amount of memory allocated for FDB entries is 2^31 * 128B =
256GiB, which is too much for most computers.
Mitigate this by maintaining a per bridge count of those automatically
generated entries in fdb_n_learned, and a limit in fdb_max_learned. If
the limit is hit new entries are not learned anymore.
For backwards compatibility the default setting of 0 disables the limit.
User-added entries by netlink or from bridge or bridge port addresses
are never blocked and do not count towards that limit.
Introduce a new fdb entry flag BR_FDB_DYNAMIC_LEARNED to keep track of
whether an FDB entry is included in the count. The flag is enabled for
dynamically learned entries, and disabled for all other entries. This
should be equivalent to BR_FDB_ADDED_BY_USER and BR_FDB_LOCAL being unset,
but contrary to the two flags it can be toggled atomically.
Atomicity is required here, as there are multiple callers that modify the
flags, but are not under a common lock (br_fdb_update is the exception
for br->hash_lock, br_fdb_external_learn_add for RTNL).
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Johannes Nixdorf <jnixdorf-oss@avm.de>
Link: https://lore.kernel.org/r/20231016-fdb_limit-v5-2-32cddff87758@avm.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of the following fdb limit for dynamically learned entries,
allow fdb_create to detect that the entry was added by the user. This
way it can skip applying the limit in this case.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Johannes Nixdorf <jnixdorf-oss@avm.de>
Link: https://lore.kernel.org/r/20231016-fdb_limit-v5-1-32cddff87758@avm.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The merge commit 9271686937 ("Merge branch 'br-flush-filtering'")
added support for FDB flushing in bridge driver. The following patches
will extend VXLAN driver to support FDB flushing as well. The netlink
message for bulk delete is shared between the drivers. With the existing
implementation, there is no way to prevent user from flushing with
attributes that are not supported per driver. For example, when VNI will
be added, user will not get an error for flush FDB entries in bridge
with VNI, although this attribute is not relevant for bridge.
As preparation for support of FDB flush in VXLAN driver, move the policy
to be handled in bridge driver, later a new policy for VXLAN will be
added in VXLAN driver. Do not pass 'vid' as part of ndo_fdb_del_bulk(),
as this field is relevant only for bridge.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
n->output field can be read locklessly, while a writer
might change the pointer concurrently.
Add missing annotations to prevent load-store tearing.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long ago we set out to remove the kitchen sink on kernel/sysctl.c arrays and
placings sysctls to their own sybsystem or file to help avoid merge conflicts.
Matthew Wilcox pointed out though that if we're going to do that we might as
well also *save* space while at it and try to remove the extra last sysctl
entry added at the end of each array, a sentintel, instead of bloating the
kernel by adding a new sentinel with each array moved.
Doing that was not so trivial, and has required slowing down the moves of
kernel/sysctl.c arrays and measuring the impact on size by each new move.
The complex part of the effort to help reduce the size of each sysctl is being
done by the patient work of el señor Don Joel Granados. A lot of this is truly
painful code refactoring and testing and then trying to measure the savings of
each move and removing the sentinels. Although Joel already has code which does
most of this work, experience with sysctl moves in the past shows is we need to
be careful due to the slew of odd build failures that are possible due to the
amount of random Kconfig options sysctls use.
To that end Joel's work is split by first addressing the major housekeeping
needed to remove the sentinels, which is part of this merge request. The rest
of the work to actually remove the sentinels will be done later in future
kernel releases.
At first I was only going to send his first 7 patches of his patch series,
posted 1 month ago, but in retrospect due to the testing the changes have
received in linux-next and the minor changes they make this goes with the
entire set of patches Joel had planned: just sysctl house keeping. There are
networking changes but these are part of the house keeping too.
The preliminary math is showing this will all help reduce the overall build
time size of the kernel and run time memory consumed by the kernel by about
~64 bytes per array where we are able to remove each sentinel in the future.
That also means there is no more bloating the kernel with the extra ~64 bytes
per array moved as no new sentinels are created.
Most of this has been in linux-next for about a month, the last 7 patches took
a minor refresh 2 week ago based on feedback.
-----BEGIN PGP SIGNATURE-----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=sq2p
-----END PGP SIGNATURE-----
Merge tag 'sysctl-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull sysctl updates from Luis Chamberlain:
"Long ago we set out to remove the kitchen sink on kernel/sysctl.c
arrays and placings sysctls to their own sybsystem or file to help
avoid merge conflicts. Matthew Wilcox pointed out though that if we're
going to do that we might as well also *save* space while at it and
try to remove the extra last sysctl entry added at the end of each
array, a sentintel, instead of bloating the kernel by adding a new
sentinel with each array moved.
Doing that was not so trivial, and has required slowing down the moves
of kernel/sysctl.c arrays and measuring the impact on size by each new
move.
The complex part of the effort to help reduce the size of each sysctl
is being done by the patient work of el señor Don Joel Granados. A lot
of this is truly painful code refactoring and testing and then trying
to measure the savings of each move and removing the sentinels.
Although Joel already has code which does most of this work,
experience with sysctl moves in the past shows is we need to be
careful due to the slew of odd build failures that are possible due to
the amount of random Kconfig options sysctls use.
To that end Joel's work is split by first addressing the major
housekeeping needed to remove the sentinels, which is part of this
merge request. The rest of the work to actually remove the sentinels
will be done later in future kernel releases.
The preliminary math is showing this will all help reduce the overall
build time size of the kernel and run time memory consumed by the
kernel by about ~64 bytes per array where we are able to remove each
sentinel in the future. That also means there is no more bloating the
kernel with the extra ~64 bytes per array moved as no new sentinels
are created"
* tag 'sysctl-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
sysctl: Use ctl_table_size as stopping criteria for list macro
sysctl: SIZE_MAX->ARRAY_SIZE in register_net_sysctl
vrf: Update to register_net_sysctl_sz
networking: Update to register_net_sysctl_sz
netfilter: Update to register_net_sysctl_sz
ax.25: Update to register_net_sysctl_sz
sysctl: Add size to register_net_sysctl function
sysctl: Add size arg to __register_sysctl_init
sysctl: Add size to register_sysctl
sysctl: Add a size arg to __register_sysctl_table
sysctl: Add size argument to init_header
sysctl: Add ctl_table_size to ctl_table_header
sysctl: Use ctl_table_header in list_for_each_table_entry
sysctl: Prefer ctl_table_header in proc_sysctl
When compiling with gcc 13 and CONFIG_FORTIFY_SOURCE=y, the following
warning appears:
In function ‘fortify_memcpy_chk’,
inlined from ‘size_entry_mwt’ at net/bridge/netfilter/ebtables.c:2118:2:
./include/linux/fortify-string.h:592:25: error: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field (2nd parameter);
maybe use struct_group()? [-Werror=attribute-warning]
592 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The compiler is complaining:
memcpy(&offsets[1], &entry->watchers_offset,
sizeof(offsets) - sizeof(offsets[0]));
where memcpy reads beyong &entry->watchers_offset to copy
{watchers,target,next}_offset altogether into offsets[]. Silence the
warning by wrapping these three up via struct_group().
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Move from register_net_sysctl to register_net_sysctl_sz for all the
netfilter related files. Do this while making sure to mirror the NULL
assignments with a table_size of zero for the unprivileged users.
We need to move to the new function in preparation for when we change
SIZE_MAX to ARRAY_SIZE() in the register_net_sysctl macro. Failing to do
so would erroneously allow ARRAY_SIZE() to be called on a pointer. We
hold off the SIZE_MAX to ARRAY_SIZE change until we have migrated all
the relevant net sysctl registering functions to register_net_sysctl_sz
in subsequent commits.
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Since commit 19e3a9c90c ("net: bridge: convert multicast to generic rhashtable")
this is not used, so can remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230726143141.11704-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a front panel joins a bridge via another netdevice (typically a LAG),
the driver needs to learn about the objects configured on the bridge port.
When the bridge port is offloaded by the driver for the first time, this
can be achieved by passing a notifier to switchdev_bridge_port_offload().
The notifier is then invoked for the individual objects (such as VLANs)
configured on the bridge, and can look for the interesting ones.
Calling switchdev_bridge_port_offload() when the second port joins the
bridge lower is unnecessary, but the replay is still needed. To that end,
add a new function, switchdev_bridge_port_replay(), which does only the
replay part of the _offload() function in exactly the same way as that
function.
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two kinds of MDB entries to be replayed: port MDB entries, and
host MDB entries. They are both replayed by br_switchdev_mdb_replay(). If
the driver supports one kind, but lacks the other, the first -EOPNOTSUPP
returned terminates the whole replay, including any further still-supported
objects in the list.
For this to cause issues, there must be MDB entries for both the host and
the port being replayed. In that case, if the driver bails out from
handling the host entry, the port entries are never replayed. However, the
replay is currently only done when a switchdev port joins a bridge. There
would be no port memberships at that point. Thus despite being erroneous,
the code does not cause observable bugs.
This is not an issue with other object kinds either, because there, each
function replays one object kind. If a driver does not support that kind,
it makes sense to bail out early. -EOPNOTSUPP is then ignored in
nbp_switchdev_sync_objs().
For MDB, suppress the -EOPNOTSUPP error code in br_switchdev_mdb_replay()
already, so that the whole list gets replayed.
The reason we need this patch is that a future patch will introduce a
replay that should be used when a front-panel port netdevice is enslaved to
a bridge lower, in particular a LAG. The LAG netdevice can already have
both host and port MDB entries. The port entries need to be replayed so
that they are offloaded on the port that joins the LAG.
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new bridge port attribute that allows attaching a nexthop object
ID to an skb that is redirected to a backup bridge port with VLAN
tunneling enabled.
Specifically, when redirecting a known unicast packet, read the backup
nexthop ID from the bridge port that lost its carrier and set it in the
bridge control block of the skb before forwarding it via the backup
port. Note that reading the ID from the bridge port should not result in
a cache miss as the ID is added next to the 'backup_port' field that was
already accessed. After this change, the 'state' field still stays on
the first cache line, together with other data path related fields such
as 'flags and 'vlgrp':
struct net_bridge_port {
struct net_bridge * br; /* 0 8 */
struct net_device * dev; /* 8 8 */
netdevice_tracker dev_tracker; /* 16 0 */
struct list_head list; /* 16 16 */
long unsigned int flags; /* 32 8 */
struct net_bridge_vlan_group * vlgrp; /* 40 8 */
struct net_bridge_port * backup_port; /* 48 8 */
u32 backup_nhid; /* 56 4 */
u8 priority; /* 60 1 */
u8 state; /* 61 1 */
u16 port_no; /* 62 2 */
/* --- cacheline 1 boundary (64 bytes) --- */
[...]
} __attribute__((__aligned__(8)));
When forwarding an skb via a bridge port that has VLAN tunneling
enabled, check if the backup nexthop ID stored in the bridge control
block is valid (i.e., not zero). If so, instead of attaching the
pre-allocated metadata (that only has the tunnel key set), allocate a
new metadata, set both the tunnel key and the nexthop object ID and
attach it to the skb.
By default, do not dump the new attribute to user space as a value of
zero is an invalid nexthop object ID.
The above is useful for EVPN multihoming. When one of the links
composing an Ethernet Segment (ES) fails, traffic needs to be redirected
towards the host via one of the other ES peers. For example, if a host
is multihomed to three different VTEPs, the backup port of each ES link
needs to be set to the VXLAN device and the backup nexthop ID needs to
point to an FDB nexthop group that includes the IP addresses of the
other two VTEPs. The VXLAN driver will extract the ID from the metadata
of the redirected skb, calculate its flow hash and forward it towards
one of the other VTEPs. If the ID does not exist, or represents an
invalid nexthop object, the VXLAN driver will drop the skb. This
relieves the bridge driver from the need to validate the ID.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the synchronization rules for .ndo_get_stats() as seen in
Documentation/networking/netdevices.rst, acquiring a plain spin_lock()
should not be illegal, but the bridge driver implementation makes it so.
After running these commands, I am being faced with the following
lockdep splat:
$ ip link add link swp0 name macsec0 type macsec encrypt on && ip link set swp0 up
$ ip link add dev br0 type bridge vlan_filtering 1 && ip link set br0 up
$ ip link set macsec0 master br0 && ip link set macsec0 up
========================================================
WARNING: possible irq lock inversion dependency detected
6.4.0-04295-g31b577b4bd4a #603 Not tainted
--------------------------------------------------------
swapper/1/0 just changed the state of lock:
ffff6bd348724cd8 (&br->lock){+.-.}-{3:3}, at: br_forward_delay_timer_expired+0x34/0x198
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&ocelot->stats_lock){+.+.}-{3:3}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Chain exists of:
&br->lock --> &br->hash_lock --> &ocelot->stats_lock
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ocelot->stats_lock);
local_irq_disable();
lock(&br->lock);
lock(&br->hash_lock);
<Interrupt>
lock(&br->lock);
*** DEADLOCK ***
(details about the 3 locks skipped)
swp0 is instantiated by drivers/net/dsa/ocelot/felix.c, and this
only matters to the extent that its .ndo_get_stats64() method calls
spin_lock(&ocelot->stats_lock).
Documentation/locking/lockdep-design.rst says:
| A lock is irq-safe means it was ever used in an irq context, while a lock
| is irq-unsafe means it was ever acquired with irq enabled.
(...)
| Furthermore, the following usage based lock dependencies are not allowed
| between any two lock-classes::
|
| <hardirq-safe> -> <hardirq-unsafe>
| <softirq-safe> -> <softirq-unsafe>
Lockdep marks br->hash_lock as softirq-safe, because it is sometimes
taken in softirq context (for example br_fdb_update() which runs in
NET_RX softirq), and when it's not in softirq context it blocks softirqs
by using spin_lock_bh().
Lockdep marks ocelot->stats_lock as softirq-unsafe, because it never
blocks softirqs from running, and it is never taken from softirq
context. So it can always be interrupted by softirqs.
There is a call path through which a function that holds br->hash_lock:
fdb_add_hw_addr() will call a function that acquires ocelot->stats_lock:
ocelot_port_get_stats64(). This can be seen below:
ocelot_port_get_stats64+0x3c/0x1e0
felix_get_stats64+0x20/0x38
dsa_slave_get_stats64+0x3c/0x60
dev_get_stats+0x74/0x2c8
rtnl_fill_stats+0x4c/0x150
rtnl_fill_ifinfo+0x5cc/0x7b8
rtmsg_ifinfo_build_skb+0xe4/0x150
rtmsg_ifinfo+0x5c/0xb0
__dev_notify_flags+0x58/0x200
__dev_set_promiscuity+0xa0/0x1f8
dev_set_promiscuity+0x30/0x70
macsec_dev_change_rx_flags+0x68/0x88
__dev_set_promiscuity+0x1a8/0x1f8
__dev_set_rx_mode+0x74/0xa8
dev_uc_add+0x74/0xa0
fdb_add_hw_addr+0x68/0xd8
fdb_add_local+0xc4/0x110
br_fdb_add_local+0x54/0x88
br_add_if+0x338/0x4a0
br_add_slave+0x20/0x38
do_setlink+0x3a4/0xcb8
rtnl_newlink+0x758/0x9d0
rtnetlink_rcv_msg+0x2f0/0x550
netlink_rcv_skb+0x128/0x148
rtnetlink_rcv+0x24/0x38
the plain English explanation for it is:
The macsec0 bridge port is created without p->flags & BR_PROMISC,
because it is what br_manage_promisc() decides for a VLAN filtering
bridge with a single auto port.
As part of the br_add_if() procedure, br_fdb_add_local() is called for
the MAC address of the device, and this results in a call to
dev_uc_add() for macsec0 while the softirq-safe br->hash_lock is taken.
Because macsec0 does not have IFF_UNICAST_FLT, dev_uc_add() ends up
calling __dev_set_promiscuity() for macsec0, which is propagated by its
implementation, macsec_dev_change_rx_flags(), to the lower device: swp0.
This triggers the call path:
dev_set_promiscuity(swp0)
-> rtmsg_ifinfo()
-> dev_get_stats()
-> ocelot_port_get_stats64()
with a calling context that lockdep doesn't like (br->hash_lock held).
Normally we don't see this, because even though many drivers that can be
bridge ports don't support IFF_UNICAST_FLT, we need a driver that
(a) doesn't support IFF_UNICAST_FLT, *and*
(b) it forwards the IFF_PROMISC flag to another driver, and
(c) *that* driver implements ndo_get_stats64() using a softirq-unsafe
spinlock.
Condition (b) is necessary because the first __dev_set_rx_mode() calls
__dev_set_promiscuity() with "bool notify=false", and thus, the
rtmsg_ifinfo() code path won't be entered.
The same criteria also hold true for DSA switches which don't report
IFF_UNICAST_FLT. When the DSA master uses a spin_lock() in its
ndo_get_stats64() method, the same lockdep splat can be seen.
I think the deadlock possibility is real, even though I didn't reproduce
it, and I'm thinking of the following situation to support that claim:
fdb_add_hw_addr() runs on a CPU A, in a context with softirqs locally
disabled and br->hash_lock held, and may end up attempting to acquire
ocelot->stats_lock.
In parallel, ocelot->stats_lock is currently held by a thread B (say,
ocelot_check_stats_work()), which is interrupted while holding it by a
softirq which attempts to lock br->hash_lock.
Thread B cannot make progress because br->hash_lock is held by A. Whereas
thread A cannot make progress because ocelot->stats_lock is held by B.
When taking the issue at face value, the bridge can avoid that problem
by simply making the ports promiscuous from a code path with a saner
calling context (br->hash_lock not held). A bridge port without
IFF_UNICAST_FLT is going to become promiscuous as soon as we call
dev_uc_add() on it (which we do unconditionally), so why not be
preemptive and make it promiscuous right from the beginning, so as to
not be taken by surprise.
With this, we've broken the links between code that holds br->hash_lock
or br->lock and code that calls into the ndo_change_rx_flags() or
ndo_get_stats64() ops of the bridge port.
Fixes: 2796d0c648 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For EVPN non-DF (Designated Forwarder) filtering we need to be able to
prevent decapsulated traffic from being flooded to a multi-homed host.
Filtering of multicast and broadcast traffic can be achieved using the
following flower filter:
# tc filter add dev bond0 egress pref 1 proto all flower indev vxlan0 dst_mac 01:00:00:00:00:00/01:00:00:00:00:00 action drop
Unlike broadcast and multicast traffic, it is not currently possible to
filter unknown unicast traffic. The classification into unknown unicast
is performed by the bridge driver, but is not visible to other layers
such as tc.
Solve this by adding a new 'l2_miss' bit to the tc skb extension. Clear
the bit whenever a packet enters the bridge (received from a bridge port
or transmitted via the bridge) and set it if the packet did not match an
FDB or MDB entry. If there is no skb extension and the bit needs to be
cleared, then do not allocate one as no extension is equivalent to the
bit being cleared. The bit is not set for broadcast packets as they
never perform a lookup and therefore never incur a miss.
A bit that is set for every flooded packet would also work for the
current use case, but it does not allow us to differentiate between
registered and unregistered multicast traffic, which might be useful in
the future.
To keep the performance impact to a minimum, the marking of packets is
guarded by the 'tc_skb_ext_tc' static key. When 'false', the skb is not
touched and an skb extension is not allocated. Instead, only a
5 bytes nop is executed, as demonstrated below for the call site in
br_handle_frame().
Before the patch:
```
memset(skb->cb, 0, sizeof(struct br_input_skb_cb));
c37b09: 49 c7 44 24 28 00 00 movq $0x0,0x28(%r12)
c37b10: 00 00
p = br_port_get_rcu(skb->dev);
c37b12: 49 8b 44 24 10 mov 0x10(%r12),%rax
memset(skb->cb, 0, sizeof(struct br_input_skb_cb));
c37b17: 49 c7 44 24 30 00 00 movq $0x0,0x30(%r12)
c37b1e: 00 00
c37b20: 49 c7 44 24 38 00 00 movq $0x0,0x38(%r12)
c37b27: 00 00
```
After the patch (when static key is disabled):
```
memset(skb->cb, 0, sizeof(struct br_input_skb_cb));
c37c29: 49 c7 44 24 28 00 00 movq $0x0,0x28(%r12)
c37c30: 00 00
c37c32: 49 8d 44 24 28 lea 0x28(%r12),%rax
c37c37: 48 c7 40 08 00 00 00 movq $0x0,0x8(%rax)
c37c3e: 00
c37c3f: 48 c7 40 10 00 00 00 movq $0x0,0x10(%rax)
c37c46: 00
#ifdef CONFIG_HAVE_JUMP_LABEL_HACK
static __always_inline bool arch_static_branch(struct static_key *key, bool branch)
{
asm_volatile_goto("1:"
c37c47: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1)
br_tc_skb_miss_set(skb, false);
p = br_port_get_rcu(skb->dev);
c37c4c: 49 8b 44 24 10 mov 0x10(%r12),%rax
```
Subsequent patches will extend the flower classifier to be able to match
on the new 'l2_miss' bit and enable / disable the static key when
filters that match on it are added / deleted.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, two functions are still
defined but have no prototype or caller. This causes a W=1 warning for
the missing prototypes:
net/bridge/br_netlink_tunnel.c:29:6: error: no previous prototype for 'vlan_tunid_inrange' [-Werror=missing-prototypes]
net/bridge/br_netlink_tunnel.c:199:5: error: no previous prototype for 'br_vlan_tunnel_info' [-Werror=missing-prototypes]
The functions are already contitional on CONFIG_BRIDGE_VLAN_FILTERING,
and I coulnd't easily figure out the right set of #ifdefs, so just
move the declarations out of the #ifdef to avoid the warning,
at a small cost in code size over a more elaborate fix.
Fixes: 188c67dd19 ("net: bridge: vlan options: add support for tunnel id dumping")
Fixes: 569da08228 ("net: bridge: vlan options: add support for tunnel mapping set/del")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230516194625.549249-3-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new bridge port attribute that allows user space to enable
per-{Port, VLAN} neighbor suppression. Example:
# bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]'
false
# bridge link set dev swp1 neigh_vlan_suppress on
# bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]'
true
# bridge link set dev swp1 neigh_vlan_suppress off
# bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]'
false
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new VLAN attribute that allows user space to set the neighbor
suppression state of the port VLAN. Example:
# bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]'
false
# bridge vlan set vid 10 dev swp1 neigh_suppress on
# bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]'
true
# bridge vlan set vid 10 dev swp1 neigh_suppress off
# bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]'
false
# bridge vlan set vid 10 dev br0 neigh_suppress on
Error: bridge: Can't set neigh_suppress for non-port vlans.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge is not VLAN-aware (i.e., VLAN ID is 0), determine if
neighbor suppression is enabled on a given bridge port solely based on
the existing 'BR_NEIGH_SUPPRESS' flag.
Otherwise, if the bridge is VLAN-aware, first check if per-{Port, VLAN}
neighbor suppression is enabled on the given bridge port using the
'BR_NEIGH_VLAN_SUPPRESS' flag. If so, look up the VLAN and check whether
it has neighbor suppression enabled based on the per-VLAN
'BR_VLFLAG_NEIGH_SUPPRESS_ENABLED' flag.
If the bridge is VLAN-aware, but the bridge port does not have
per-{Port, VLAN} neighbor suppression enabled, then fallback to
determine neighbor suppression based on the 'BR_NEIGH_SUPPRESS' flag.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are various places in the bridge data path that check
whether neighbor suppression is enabled on a given bridge port.
As a preparation for per-{Port, VLAN} neighbor suppression, encapsulate
this logic in a function and pass the VLAN ID of the packet as an
argument.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge driver gates the neighbor suppression code behind an internal
per-bridge flag called 'BROPT_NEIGH_SUPPRESS_ENABLED'. The flag is set
when at least one bridge port has neighbor suppression enabled.
As a preparation for per-{Port, VLAN} neighbor suppression, make sure
the global flag is also set if per-{Port, VLAN} neighbor suppression is
enabled. That is, when the 'BR_NEIGH_VLAN_SUPPRESS' flag is set on at
least one bridge port.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two internal flags that will be used to enable / disable per-{Port,
VLAN} neighbor suppression:
1. 'BR_NEIGH_VLAN_SUPPRESS': A per-port flag used to indicate that
per-{Port, VLAN} neighbor suppression is enabled on the bridge port.
When set, 'BR_NEIGH_SUPPRESS' has no effect.
2. 'BR_VLFLAG_NEIGH_SUPPRESS_ENABLED': A per-VLAN flag used to indicate
that neighbor suppression is enabled on the given VLAN.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to add per-{Port, VLAN} neighbor
suppression, which will require br_flood() to potentially suppress ARP /
NS packets on a per-{Port, VLAN} basis.
As a preparation, pass the VLAN ID of the packet as another argument to
br_flood().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge does not flood ARP / NS packets for which a reply was sent to
bridge ports that have neighbor suppression enabled.
Subsequent patches are going to add per-{Port, VLAN} neighbor
suppression, which is going to make it more expensive to check whether
neighbor suppression is enabled since a VLAN lookup will be required.
Therefore, instead of unnecessarily performing this lookup for every
packet, only perform it for ARP / NS packets for which a reply was sent.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a structural problem in switchdev, where the flag bits in
struct switchdev_notifier_fdb_info (added_by_user, is_local etc) only
represent a simplified / denatured view of what's in struct
net_bridge_fdb_entry :: flags (BR_FDB_ADDED_BY_USER, BR_FDB_LOCAL etc).
Each time we want to pass more information about struct
net_bridge_fdb_entry :: flags to struct switchdev_notifier_fdb_info
(here, BR_FDB_STATIC), we find that FDB entries were already notified to
switchdev with no regard to this flag, and thus, switchdev drivers had
no indication whether the notified entries were static or not.
For example, this command:
ip link add br0 type bridge && ip link set swp0 master br0
bridge fdb add dev swp0 00:01:02:03:04:05 master dynamic
has never worked as intended with switchdev. It causes a struct
net_bridge_fdb_entry to be passed to br_switchdev_fdb_notify() which has
a single flag set: BR_FDB_ADDED_BY_USER.
This is further passed to the switchdev notifier chain, where interested
drivers have no choice but to assume this is a static (does not age) and
sticky (does not migrate) FDB entry. So currently, all drivers offload
it to hardware as such, as can be seen below ("offload" is set).
bridge fdb get 00:01:02:03:04:05 dev swp0 master
00:01:02:03:04:05 dev swp0 offload master br0
The software FDB entry expires $ageing_time centiseconds after the
kernel last sees a packet with this MAC SA, and the bridge notifies its
deletion as well, so it eventually disappears from hardware too.
This is a problem, because it is actually desirable to start offloading
"master dynamic" FDB entries correctly - they should expire $ageing_time
centiseconds after the *hardware* port last sees a packet with this
MAC SA - and this is how the current incorrect behavior was discovered.
With an offloaded data plane, it can be expected that software only sees
exception path packets, so an otherwise active dynamic FDB entry would
be aged out by software sooner than it should.
With the change in place, these FDB entries are no longer offloaded:
bridge fdb get 00:01:02:03:04:05 dev swp0 master
00:01:02:03:04:05 dev swp0 master br0
and this also constitutes a better way (assuming a backport to stable
kernels) for user space to determine whether the kernel has the
capability of doing something sane with these or not.
As opposed to "master dynamic" FDB entries, on the current behavior of
which no one currently depends on (which can be deduced from the lack of
kselftests), Ido Schimmel explains that entries with the "extern_learn"
flag (BR_FDB_ADDED_BY_EXT_LEARN) should still be notified to switchdev,
since the spectrum driver listens to them (and this is kind of okay,
because although they are treated identically to "static", they are
expected to not age, and to roam).
Fixes: 6b26b51b1d ("net: bridge: Add support for notifying devices about FDB add/del")
Link: https://lore.kernel.org/netdev/20230327115206.jk5q5l753aoelwus@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230418155902.898627-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recent attempt to ensure PREROUTING hook is executed again when a
decrypted ipsec packet received on a bridge passes through the network
stack a second time broke the physdev match in INPUT hook.
We can't discard the nf_bridge info strct from sabotage_in hook, as
this is needed by the physdev match.
Keep the struct around and handle this with another conditional instead.
Fixes: 2b272bb558 ("netfilter: br_netfilter: disable sabotage_in hook after first suppression")
Reported-and-tested-by: Farid BENAMROUCHE <fariouche@yahoo.fr>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Under high contention dst_entry::__refcnt becomes a significant bottleneck.
atomic_inc_not_zero() is implemented with a cmpxchg() loop, which goes into
high retry rates on contention.
Switch the reference count to rcuref_t which results in a significant
performance gain. Rename the reference count member to __rcuref to reflect
the change.
The gain depends on the micro-architecture and the number of concurrent
operations and has been measured in the range of +25% to +130% with a
localhost memtier/memcached benchmark which amplifies the problem
massively.
Running the memtier/memcached benchmark over a real (1Gb) network
connection the conversion on top of the false sharing fix for struct
dst_entry::__refcnt results in a total gain in the 2%-5% range over the
upstream baseline.
Reported-by: Wangyang Guo <wangyang.guo@intel.com>
Reported-by: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230307125538.989175656@linutronix.de
Link: https://lore.kernel.org/r/20230323102800.215027837@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the upcoming VXLAN MDB implementation, the 0.0.0.0 and :: MDB entries
will act as catchall entries for unregistered IP multicast traffic in a
similar fashion to the 00:00:00:00:00:00 VXLAN FDB entry that is used to
transmit BUM traffic.
In deployments where inter-subnet multicast forwarding is used, not all
the VTEPs in a tenant domain are members in all the broadcast domains.
It is therefore advantageous to transmit BULL (broadcast, unknown
unicast and link-local multicast) and unregistered IP multicast traffic
on different tunnels. If the same tunnel was used, a VTEP only
interested in IP multicast traffic would also pull all the BULL traffic
and drop it as it is not a member in the originating broadcast domain
[1].
Prepare for this change by allowing the 0.0.0.0 group address in the
common rtnetlink MDB code and forbid it in the bridge driver. A similar
change is not needed for IPv6 because the common code only validates
that the group address is not the all-nodes address.
[1] https://datatracker.ietf.org/doc/html/draft-ietf-bess-evpn-irb-mcast#section-2.6
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the bridge driver registers handlers for MDB netlink
messages, making it impossible for other drivers to implement MDB
support.
As a preparation for VXLAN MDB support, move the MDB handlers out of the
bridge driver to the core rtnetlink code. The rtnetlink code will call
into individual drivers by invoking their previously added MDB net
device operations.
Note that while the diffstat is large, the change is mechanical. It
moves code out of the bridge driver to rtnetlink code. Also note that a
similar change was made in 2012 with commit 77162022ab ("net: add
generic PF_BRIDGE:RTM_ FDB hooks") that moved FDB handlers out of the
bridge driver to the core rtnetlink code.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the previously added MDB net device operations in the bridge
driver so that they could be invoked by core rtnetlink code in the next
patch.
The operations are identical to the existing br_mdb_{dump,add,del}
functions. The '_new' suffix will be removed in the next patch. The
functions are re-implemented in this patch to make the conversion in the
next patch easier to review.
Add dummy implementations when 'CONFIG_BRIDGE_IGMP_SNOOPING' is
disabled, so that an error will be returned to user space when it is
trying to add or delete an MDB entry. This is consistent with existing
behavior where the bridge driver does not even register rtnetlink
handlers for RTM_{NEW,DEL,GET}MDB messages when this Kconfig option is
disabled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have many lockless accesses to n->nud_state.
Before adding another one in the following patch,
add annotations to readers and writers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename br_nf_check_hbh_len() to nf_ip6_check_hbh_len() and move it
to netfilter utils, so that it can be used by other modules, like
ovs and tc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
br_nf_check_hbh_len() is a function to check the Hop-by-hop option
header, and shouldn't do pskb_trim_rcsum() there. This patch is to
pass pkt_len out to br_validate_ipv6() and do pskb_trim_rcsum()
after calling br_validate_ipv6() instead.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
In the while loop of br_nf_check_hbh_len(), similar to ip6_parse_tlv(),
before accessing 'nh[off + 1]', it should add a check 'len < 2'; and
before parsing IPV6_TLV_JUMBO, it should add a check 'optlen > len',
in case of overflows.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
When checking Hop-by-hop option header, if the option data is in
nonlinear area, it should do pskb_may_pull instead of discarding
the skb as a bad IPv6 packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
nftables equivalent for ebtables -t broute.
Implement broute meta statement to set br_netfilter_broute flag
in skb to force a packet to be routed instead of being bridged.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Florian Westphal <fw@strlen.de>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Fix broken listing of set elements when table has an owner.
2) Fix conntrack refcount leak in ctnetlink with related conntrack
entries, from Hangyu Hua.
3) Fix use-after-free/double-free in ctnetlink conntrack insert path,
from Florian Westphal.
4) Fix ip6t_rpfilter with VRF, from Phil Sutter.
5) Fix use-after-free in ebtables reported by syzbot, also from Florian.
6) Use skb->len in xt_length to deal with IPv6 jumbo packets,
from Xin Long.
7) Fix NETLINK_LISTEN_ALL_NSID with ctnetlink, from Florian Westphal.
8) Fix memleak in {ip_,ip6_,arp_}tables in ENOMEM error case,
from Pavel Tikhomirov.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: x_tables: fix percpu counter block leak on error path when creating new netns
netfilter: ctnetlink: make event listener tracking global
netfilter: xt_length: use skb len to match in length_mt6
netfilter: ebtables: fix table blob use-after-free
netfilter: ip6t_rpfilter: Fix regression with VRF interfaces
netfilter: conntrack: fix rmmod double-free race
netfilter: ctnetlink: fix possible refcount leak in ctnetlink_create_conntrack()
netfilter: nf_tables: allow to fetch set elements when table has an owner
====================
Link: https://lore.kernel.org/r/20230222092137.88637-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are not allowed to return an error at this point.
Looking at the code it looks like ret is always 0 at this
point, but its not.
t = find_table_lock(net, repl->name, &ret, &ebt_mutex);
... this can return a valid table, with ret != 0.
This bug causes update of table->private with the new
blob, but then frees the blob right away in the caller.
Syzbot report:
BUG: KASAN: vmalloc-out-of-bounds in __ebt_unregister_table+0xc00/0xcd0 net/bridge/netfilter/ebtables.c:1168
Read of size 4 at addr ffffc90005425000 by task kworker/u4:4/74
Workqueue: netns cleanup_net
Call Trace:
kasan_report+0xbf/0x1f0 mm/kasan/report.c:517
__ebt_unregister_table+0xc00/0xcd0 net/bridge/netfilter/ebtables.c:1168
ebt_unregister_table+0x35/0x40 net/bridge/netfilter/ebtables.c:1372
ops_exit_list+0xb0/0x170 net/core/net_namespace.c:169
cleanup_net+0x4ee/0xb10 net/core/net_namespace.c:613
...
ip(6)tables appears to be ok (ret should be 0 at this point) but make
this more obvious.
Fixes: c58dd2dd44 ("netfilter: Can't fail and free after table replacement")
Reported-by: syzbot+f61594de72d6705aea03@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definition to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Future patches are going to move parts of the bridge MDB code to the
common rtnetlink code in preparation for VXLAN MDB support. To
facilitate code sharing between both drivers, move the validation of the
top level attributes in RTM_{NEW,DEL}MDB messages to a policy that will
eventually be moved to the rtnetlink code.
Use 'NLA_NESTED' for 'MDBA_SET_ENTRY_ATTRS' instead of
NLA_POLICY_NESTED() as this attribute is going to be validated using
different policies in the underlying drivers.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The purpose of the sequence generation counter in the netlink callback
is to identify if a multipart dump is consistent or not by calling
nl_dump_check_consistent() whenever a message is generated.
The function is not invoked by the MDB code, rendering the sequence
generation counter assignment pointless. Remove it.
Note that even if the function was invoked, we still could not
accurately determine if the dump is consistent or not, as there is no
sequence generation counter for MDB entries, unlike nexthop objects, for
example.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'MDB_PG_FLAGS_PERMANENT' and 'MDB_PERMANENT' happen to have the same
value, but the latter is uAPI and cannot change, so use it when dumping
an MDB entry.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch added accounting for number of MDB entries per port and
per port-VLAN, and the logic to verify that these values stay within
configured bounds. However it didn't provide means to actually configure
those bounds or read the occupancy. This patch does that.
Two new netlink attributes are added for the MDB occupancy:
IFLA_BRPORT_MCAST_N_GROUPS for the per-port occupancy and
BRIDGE_VLANDB_ENTRY_MCAST_N_GROUPS for the per-port-VLAN occupancy.
And another two for the maximum number of MDB entries:
IFLA_BRPORT_MCAST_MAX_GROUPS for the per-port maximum, and
BRIDGE_VLANDB_ENTRY_MCAST_MAX_GROUPS for the per-port-VLAN one.
Note that the two new IFLA_BRPORT_ attributes prompt bumping of
RTNL_SLAVE_MAX_TYPE to size the slave attribute tables large enough.
The new attributes are used like this:
# ip link add name br up type bridge vlan_filtering 1 mcast_snooping 1 \
mcast_vlan_snooping 1 mcast_querier 1
# ip link set dev v1 master br
# bridge vlan add dev v1 vid 2
# bridge vlan set dev v1 vid 1 mcast_max_groups 1
# bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 1
# bridge mdb add dev br port v1 grp 230.1.2.4 temp vid 1
Error: bridge: Port-VLAN is already in 1 groups, and mcast_max_groups=1.
# bridge link set dev v1 mcast_max_groups 1
# bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 2
Error: bridge: Port is already in 1 groups, and mcast_max_groups=1.
# bridge -d link show
5: v1@v2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master br [...]
[...] mcast_n_groups 1 mcast_max_groups 1
# bridge -d vlan show
port vlan-id
br 1 PVID Egress Untagged
state forwarding mcast_router 1
v1 1 PVID Egress Untagged
[...] mcast_n_groups 1 mcast_max_groups 1
2
[...] mcast_n_groups 0 mcast_max_groups 0
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDB maintained by the bridge is limited. When the bridge is configured
for IGMP / MLD snooping, a buggy or malicious client can easily exhaust its
capacity. In SW datapath, the capacity is configurable through the
IFLA_BR_MCAST_HASH_MAX parameter, but ultimately is finite. Obviously a
similar limit exists in the HW datapath for purposes of offloading.
In order to prevent the issue of unilateral exhaustion of MDB resources,
introduce two parameters in each of two contexts:
- Per-port and per-port-VLAN number of MDB entries that the port
is member in.
- Per-port and (when BROPT_MCAST_VLAN_SNOOPING_ENABLED is enabled)
per-port-VLAN maximum permitted number of MDB entries, or 0 for
no limit.
The per-port multicast context is used for tracking of MDB entries for the
port as a whole. This is available for all bridges.
The per-port-VLAN multicast context is then only available on
VLAN-filtering bridges on VLANs that have multicast snooping on.
With these changes in place, it will be possible to configure MDB limit for
bridge as a whole, or any one port as a whole, or any single port-VLAN.
Note that unlike the global limit, exhaustion of the per-port and
per-port-VLAN maximums does not cause disablement of multicast snooping.
It is also permitted to configure the local limit larger than hash_max,
even though that is not useful.
In this patch, introduce only the accounting for number of entries, and the
max field itself, but not the means to toggle the max. The next patch
introduces the netlink APIs to toggle and read the values.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is getting more to clean up in the following patches.
Structuring the cleanups in one labeled block will allow reusing the same
cleanup from several places.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since cleaning up the effects of br_multicast_new_port_group() just
consists of delisting and freeing the memory, the function
br_mdb_add_group_star_g() inlines the corresponding code. In the following
patches, number of per-port and per-port-VLAN MDB entries is going to be
maintained, and that counter will have to be updated. Because that logic
is going to be hidden in the br_multicast module, introduce a new hook
intended to again remove a newly-created group.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that br_multicast_new_port_group() takes an extack argument, move
setting the extack there. The downside is that the error messages end
up being less specific (the function cannot distinguish between (S,G)
and (*,G) groups). However, the alternative is to check in the caller
whether the callee set the extack, and if it didn't, set it. But that
is only done when the callee is not exactly known. (E.g. in case of a
notifier invocation.)
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to set an extack in br_multicast_new_port_group().
Eventually, this function will check for per-port and per-port-vlan
MDB maximums, and will use the extack to communicate the reason for
the bounce.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make any attributes newly-added to br_port_policy or vlan_tunnel_policy
parsed strictly, to prevent userspace from passing garbage. Note that this
patchset only touches the former policy. The latter was adjusted for
completeness' sake. There do not appear to be other _deprecated calls
with non-NULL policies.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdev common pattern, extack pointer is forwarded to the drivers
to be filled with error message. However, the caller can easily
overwrite the filled message.
Instead of adding multiple "if (!extack->_msg)" checks before any
NL_SET_ERR_MSG() call, which appears after call to the driver, let's
add new macro to common code.
[1] https://lore.kernel.org/all/Y9Irgrgf3uxOjwUm@unreal
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/6993fac557a40a1973dfa0095107c3d03d40bec1.1675171790.git.leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These 3 places in bridge netfilter are called on RX path after GRO
and IPv4 TCP GSO packets may come through, so replace iph tot_len
accessing with skb_ip_totlen() in there.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using a xfrm interface in a bridged setup (the outgoing device is
bridged), the incoming packets in the xfrm interface are only tracked
in the outgoing direction.
$ brctl show
bridge name interfaces
br_eth1 eth1
$ conntrack -L
tcp 115 SYN_SENT src=192... dst=192... [UNREPLIED] ...
If br_netfilter is enabled, the first (encrypted) packet is received onR
eth1, conntrack hooks are called from br_netfilter emulation which
allocates nf_bridge info for this skb.
If the packet is for local machine, skb gets passed up the ip stack.
The skb passes through ip prerouting a second time. br_netfilter
ip_sabotage_in supresses the re-invocation of the hooks.
After this, skb gets decrypted in xfrm layer and appears in
network stack a second time (after decryption).
Then, ip_sabotage_in is called again and suppresses netfilter
hook invocation, even though the bridge layer never called them
for the plaintext incarnation of the packet.
Free the bridge info after the first suppression to avoid this.
I was unable to figure out where the regression comes from, as far as i
can see br_netfilter always had this problem; i did not expect that skb
is looped again with different headers.
Fixes: c4b0e771f9 ("netfilter: avoid using skb->nf_bridge directly")
Reported-and-tested-by: Wolfgang Nothdurft <wolfgang@linogate.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
Now that user space can specify additional attributes of port group
entries such as filter mode and source list, it makes sense to allow
user space to atomically modify these attributes by replacing entries
instead of forcing user space to delete the entries and add them back.
Replace MDB port group entries when the 'NLM_F_REPLACE' flag is
specified in the netlink message header.
When a (*, G) entry is replaced, update the following attributes: Source
list, state, filter mode, protocol and flags. If the entry is temporary
and in EXCLUDE mode, reset the group timer to the group membership
interval. If the entry is temporary and in INCLUDE mode, reset the
source timers of associated sources to the group membership interval.
Examples:
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.2 filter_mode include
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.2 permanent filter_mode include proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode include source_list 192.0.2.2/0.00,192.0.2.1/0.00 proto static 0.00
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.3 filter_mode exclude proto zebra
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 permanent filter_mode include proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude source_list 192.0.2.3/0.00,192.0.2.1/0.00 proto zebra 0.00
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 temp source_list 192.0.2.4,192.0.2.3 filter_mode include proto bgp
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.4 temp filter_mode include proto bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 temp filter_mode include proto bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 temp filter_mode include source_list 192.0.2.4/259.44,192.0.2.3/259.44 proto bgp 0.00
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the 'MDBE_ATTR_RTPORT' attribute to allow user space to specify the
routing protocol of the MDB port group entry. Enforce a minimum value of
'RTPROT_STATIC' to prevent user space from using protocol values that
should only be set by the kernel (e.g., 'RTPROT_KERNEL'). Maintain
backward compatibility by defaulting to 'RTPROT_STATIC'.
The protocol is already visible to user space in RTM_NEWMDB responses
and notifications via the 'MDBA_MDB_EATTR_RTPROT' attribute.
The routing protocol allows a routing daemon to distinguish between
entries configured by it and those configured by the administrator. Once
MDB flush is supported, the protocol can be used as a criterion
according to which the flush is performed.
Examples:
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto kernel
Error: integer out of range.
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto static
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent proto zebra
# bridge mdb add dev br0 port dummy10 grp 239.1.1.2 permanent source_list 198.51.100.1,198.51.100.2 filter_mode include proto 250
# bridge -d mdb show
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.2 permanent filter_mode include proto 250
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.1 permanent filter_mode include proto 250
dev br0 port dummy10 grp 239.1.1.2 permanent filter_mode include source_list 198.51.100.2/0.00,198.51.100.1/0.00 proto 250
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude proto static
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new netlink attributes to the RTM_NEWMDB request that allow user
space to add (*, G) with a source list and filter mode.
The RTM_NEWMDB message can already dump such entries (created by the
kernel) so there is no need to add dump support. However, the message
contains a different set of attributes depending if it is a request or a
response. The naming and structure of the new attributes try to follow
the existing ones used in the response.
Request:
[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_SET_ENTRY ]
struct br_mdb_entry
[ MDBA_SET_ENTRY_ATTRS ]
[ MDBE_ATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBE_ATTR_SRC_LIST ] // new
[ MDBE_SRC_LIST_ENTRY ]
[ MDBE_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ ...]
[ MDBE_ATTR_GROUP_MODE ] // new
u8
Response:
[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_MDB ]
[ MDBA_MDB_ENTRY ]
[ MDBA_MDB_ENTRY_INFO ]
struct br_mdb_entry
[ MDBA_MDB_EATTR_TIMER ]
u32
[ MDBA_MDB_EATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBA_MDB_EATTR_RTPROT ]
u8
[ MDBA_MDB_EATTR_SRC_LIST ]
[ MDBA_MDB_SRCLIST_ENTRY ]
[ MDBA_MDB_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ MDBA_MDB_SRCATTR_TIMER ]
u8
[...]
[ MDBA_MDB_EATTR_GROUP_MODE ]
u8
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for allowing user space to add (*, G) entries with a
source list and associated filter mode, add the necessary plumbing to
handle such requests.
Extend the MDB configuration structure with a currently empty source
array and filter mode that is currently hard coded to EXCLUDE.
Add the source entries and the corresponding (S, G) entries before
making the new (*, G) port group entry visible to the data path.
Handle the creation of each source entry in a similar fashion to how it
is created from the data path in response to received Membership
Reports: Create the source entry, arm the source timer (if needed), add
a corresponding (S, G) forwarding entry and finally mark the source
entry as installed (by user space).
Add the (S, G) entry by populating an MDB configuration structure and
calling br_mdb_add_group_sg() as if a new entry is created by user
space, with the sole difference that the 'src_entry' field is set to
make sure that the group timer of such entries is never armed.
Note that it is not currently possible to add more than 32 source
entries to a port group entry. If this proves to be a problem we can
either increase 'PG_SRC_ENT_LIMIT' or avoid forcing a limit on entries
created by user space.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
User space will soon be able to install a (*, G) with a source list,
prompting the creation of a (S, G) entry for each source.
In this case, the group timer of the (S, G) entry should never be set.
Solve this by adding a new field to the MDB configuration structure that
denotes whether the (S, G) corresponds to a source or not.
The field will be set in a subsequent patch where br_mdb_add_group_sg()
is called in order to create a (S, G) entry for each user provided
source.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few places where the bridge driver differentiates between
(S, G) entries installed by the kernel (in response to Membership
Reports) and those installed by user space. One of them is when deleting
an (S, G) entry corresponding to a source entry that is being deleted.
While user space cannot currently add a source entry to a (*, G), it can
add an (S, G) entry that later corresponds to a source entry created by
the reception of a Membership Report. If this source entry is later
deleted because its source timer expired or because the (*, G) entry is
being deleted, the bridge driver will not delete the corresponding (S,
G) entry if it was added by user space as permanent.
This is going to be a problem when the ability to install a (*, G) with
a source list is exposed to user space. In this case, when user space
installs the (*, G) as permanent, then all the (S, G) entries
corresponding to its source list will also be installed as permanent.
When user space deletes the (*, G), all the source entries will be
deleted and the expectation is that the corresponding (S, G) entries
will be deleted as well.
Solve this by introducing a new source entry flag denoting that the
entry was installed by user space. When the entry is deleted, delete the
corresponding (S, G) entry even if it was installed by user space as
permanent, as the flag tells us that it was installed in response to the
source entry being created.
The flag will be set in a subsequent patch where source entries are
created in response to user requests.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose __br_multicast_del_group_src() which is symmetric to
br_multicast_new_group_src() and does not remove the installed {S, G}
forwarding entry, unlike br_multicast_del_group_src().
The function will be used in the error path when user space was able to
add a new source entry, but failed to install a corresponding forwarding
entry.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, new group source entries are only created in response to
received Membership Reports. Subsequent patches are going to allow user
space to install (*, G) entries with a source list.
As a preparatory step, expose br_multicast_new_group_src() so that it
could later be invoked from the MDB code (i.e., br_mdb.c) that handles
RTM_NEWMDB messages.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subsequent patches will add memory allocations in br_mdb_config_init()
as the MDB configuration structure will include a linked list of source
entries. This memory will need to be freed regardless if br_mdb_add()
succeeded or failed.
As a preparation for this change, add a centralized error path where the
memory will be freed.
Note that br_mdb_del() already has one error path and therefore does not
require any changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subsequent patches are going to add additional validation functions and
netlink policies. Some of these functions will need to perform parsing
using nla_parse_nested() and the new policies.
In order to keep all the policies next to each other, move the current
policy to before the validation functions.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the bridge is using IGMP version 3 or MLD version 2, it handles the
addition of (*, G) and (S, G) entries differently.
When a new (S, G) port group entry is added, all the (*, G) EXCLUDE
ports need to be added to the port group of the new entry. Similarly,
when a new (*, G) EXCLUDE port group entry is added, the port needs to
be added to the port group of all the matching (S, G) entries.
Subsequent patches will create more differences between both entry
types. Namely, filter mode and source list can only be specified for (*,
G) entries.
Given the current and future differences between both entry types,
handle the addition of each entry type in a different function, thereby
avoiding the creation of one complex function.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the filter mode (i.e., INCLUDE / EXCLUDE) of MDB entries
cannot be set from user space. Instead, it is set by the kernel
according to the entry type: (*, G) entries are treated as EXCLUDE and
(S, G) entries are treated as INCLUDE. This allows the kernel to derive
the entry type from its filter mode.
Subsequent patches will allow user space to set the filter mode of (*,
G) entries, making the current assumption incorrect.
As a preparation, remove the current assumption and instead determine
the entry type from its key, which is a more direct way.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
1) Incorrect error check in nft_expr_inner_parse(), from Dan Carpenter.
2) Add DATA_SENT state to SCTP connection tracking helper, from
Sriram Yagnaraman.
3) Consolidate nf_confirm for ipv4 and ipv6, from Florian Westphal.
4) Add bitmask support for ipset, from Vishwanath Pai.
5) Handle icmpv6 redirects as RELATED, from Florian Westphal.
6) Add WARN_ON_ONCE() to impossible case in flowtable datapath,
from Li Qiong.
7) A large batch of IPVS updates to replace timer-based estimators by
kthreads to scale up wrt. CPUs and workload (millions of estimators).
Julian Anastasov says:
This patchset implements stats estimation in kthread context.
It replaces the code that runs on single CPU in timer context every 2
seconds and causing latency splats as shown in reports [1], [2], [3].
The solution targets setups with thousands of IPVS services,
destinations and multi-CPU boxes.
Spread the estimation on multiple (configured) CPUs and multiple
time slots (timer ticks) by using multiple chains organized under RCU
rules. When stats are not needed, it is recommended to use
run_estimation=0 as already implemented before this change.
RCU Locking:
- As stats are now RCU-locked, tot_stats, svc and dest which
hold estimator structures are now always freed from RCU
callback. This ensures RCU grace period after the
ip_vs_stop_estimator() call.
Kthread data:
- every kthread works over its own data structure and all
such structures are attached to array. For now we limit
kthreads depending on the number of CPUs.
- even while there can be a kthread structure, its task
may not be running, eg. before first service is added or
while the sysctl var is set to an empty cpulist or
when run_estimation is set to 0 to disable the estimation.
- the allocated kthread context may grow from 1 to 50
allocated structures for timer ticks which saves memory for
setups with small number of estimators
- a task and its structure may be released if all
estimators are unlinked from its chains, leaving the
slot in the array empty
- every kthread data structure allows limited number
of estimators. Kthread 0 is also used to initially
calculate the max number of estimators to allow in every
chain considering a sub-100 microsecond cond_resched
rate. This number can be from 1 to hundreds.
- kthread 0 has an additional job of optimizing the
adding of estimators: they are first added in
temp list (est_temp_list) and later kthread 0
distributes them to other kthreads. The optimization
is based on the fact that newly added estimator
should be estimated after 2 seconds, so we have the
time to offload the adding to chain from controlling
process to kthread 0.
- to add new estimators we use the last added kthread
context (est_add_ktid). The new estimators are linked to
the chains just before the estimated one, based on add_row.
This ensures their estimation will start after 2 seconds.
If estimators are added in bursts, common case if all
services and dests are initially configured, we may
spread the estimators to more chains and as result,
reducing the initial delay below 2 seconds.
Many thanks to Jiri Wiesner for his valuable comments
and for spending a lot of time reviewing and testing
the changes on different platforms with 48-256 CPUs and
1-8 NUMA nodes under different cpufreq governors.
The new IPVS estimators do not use workqueue infrastructure
because:
- The estimation can take long time when using multiple IPVS rules (eg.
millions estimator structures) and especially when box has multiple
CPUs due to the for_each_possible_cpu usage that expects packets from
any CPU. With est_nice sysctl we have more control how to prioritize the
estimation kthreads compared to other processes/kthreads that have
latency requirements (such as servers). As a benefit, we can see these
kthreads in top and decide if we will need some further control to limit
their CPU usage (max number of structure to estimate per kthread).
- with kthreads we run code that is read-mostly, no write/lock
operations to process the estimators in 2-second intervals.
- work items are one-shot: as estimators are processed every
2 seconds, they need to be re-added every time. This again
loads the timers (add_timer) if we use delayed works, as there are
no kthreads to do the timings.
[1] Report from Yunhong Jiang:
https://lore.kernel.org/netdev/D25792C1-1B89-45DE-9F10-EC350DC04ADC@gmail.com/
[2] https://marc.info/?l=linux-virtual-server&m=159679809118027&w=2
[3] Report from Dust:
https://archive.linuxvirtualserver.org/html/lvs-devel/2020-12/msg00000.html
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
ipvs: run_estimation should control the kthread tasks
ipvs: add est_cpulist and est_nice sysctl vars
ipvs: use kthreads for stats estimation
ipvs: use u64_stats_t for the per-cpu counters
ipvs: use common functions for stats allocation
ipvs: add rcu protection to stats
netfilter: flowtable: add a 'default' case to flowtable datapath
netfilter: conntrack: set icmpv6 redirects as RELATED
netfilter: ipset: Add support for new bitmask parameter
netfilter: conntrack: merge ipv4+ipv6 confirm functions
netfilter: conntrack: add sctp DATA_SENT state
netfilter: nft_inner: fix IS_ERR() vs NULL check
====================
Link: https://lore.kernel.org/r/20221211101204.1751-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'group' argument is not modified, so mark it as 'const'. It will
allow us to constify arguments of the callers of this function in future
patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop the first three arguments and instead extract them from the MDB
configuration structure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The checks only require information parsed from the RTM_NEWMDB netlink
message and do not rely on any state stored in the bridge driver.
Therefore, there is no need to perform the checks in the critical
section under the multicast lock.
Move the checks out of the critical section.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The parsing of the netlink messages and the validity checks are now
performed in br_mdb_config_init() so we can remove br_mdb_parse().
This finally allows us to stop passing netlink attributes deep in the
MDB control path and only use the MDB configuration structure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDB group key (i.e., {source, destination, protocol, VID}) is
currently determined under the multicast lock from the netlink
attributes. Instead, use the group key from the MDB configuration
structure that was prepared before acquiring the lock.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As an intermediate step towards only using the new MDB configuration
structure, pass it further in the control path instead of passing
individual attributes.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDB configuration structure (i.e., struct br_mdb_config) now
includes all the necessary information from the parsed RTM_{NEW,DEL}MDB
netlink messages, so use it.
This will later allow us to delete the calls to br_mdb_parse() from
br_mdb_add() and br_mdb_del().
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These checks are now redundant as they are performed by
br_mdb_config_init() while parsing the RTM_{NEW,DEL}MDB messages.
Remove them.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
