The v4l2_subdev_s_stream_helper() helper can be used by subdevs that
implement the stream-aware .enable_streams() and .disable_streams()
operations to implement .s_stream(). This is limited to subdevs that
have a single source pad.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add two new subdev pad operations, .enable_streams() and
.disable_streams(), to allow control of individual streams per pad. This
is a superset of what the video .s_stream() operation implements.
To help with handling of backward compatibility, add two wrapper
functions around those operations, and require their usage in drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a helper function to translate streams between two pads of a subdev,
using the subdev's internal routing table.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a v4l2_subdev_routing_validate() helper for verifying routing for
common cases like only allowing non-overlapping 1-to-1 streams.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l2_subdev_set_routing_with_fmt() is the same as
v4l2_subdev_set_routing(), but additionally initializes all the streams
with the given format.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add two helper functions to make dealing with streams easier:
v4l2_subdev_routing_find_opposite_end - given a routing table and a pad
+ stream, return the pad + stream on the opposite side of the subdev.
v4l2_subdev_state_get_opposite_stream_format - return a pointer to the
format on the pad + stream on the opposite side from the given pad +
stream.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support to manage configurations (format, crop, compose) per stream,
instead of per pad. This is accomplished with data structures that hold
an array of all subdev's stream configurations.
The number of streams can vary at runtime based on routing. Every time
the routing is changed, the stream configurations need to be
re-initialized.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a for_each_active_route() macro to replace the repeated pattern
of iterating on the active routes of a routing table.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a helper function to set the subdev routing. The helper can be used
from subdev driver's set_routing op to store the routing table.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a v4l2_subdev_has_pad_interdep() helper function which can be used
for media_entity_operations.has_pad_interdep op.
It considers two pads interdependent if there is an active route between
pad0 and pad1.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for subdev internal routing. A route is defined as a single
stream from a sink pad to a source pad.
The userspace can configure the routing via two new ioctls,
VIDIOC_SUBDEV_G_ROUTING and VIDIOC_SUBDEV_S_ROUTING, and subdevs can
implement the functionality with v4l2_subdev_pad_ops.set_routing().
- Add sink and source streams for multiplexed links
- Copy the argument back in case of an error. This is needed to let the
caller know the number of routes.
- Expand and refine documentation.
- Make the 'routes' pointer a __u64 __user pointer so that a compat32
version of the ioctl is not required.
- Add struct v4l2_subdev_krouting to be used for subdevice operations.
- Fix typecasing warnings
- Check sink & source pad types
- Add 'which' field
- Routing to subdev state
- Dropped get_routing subdev op
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add subdev flag V4L2_SUBDEV_FL_STREAMS. It is used to indicate that the
subdev supports the new API with multiplexed streams (routing, stream
configs).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Document the function parameters, the requirements on the pad0 and pad1
arguments, the locking requirements and the return value. Also improve
the documentation of the corresponding .has_pad_interdep() operation,
stating clearly that the operation must be called through the
media_entity_has_pad_interdep() function only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The davinci dm3xx/dm644x platforms are gone now, and the remaining
da8xx platforms do not use the vpbe driver, so the driver can be
removed as well.
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This driver was for the davinci dm644x and dm3xx platforms that are
now removed from the kernel, so there are no more users.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tag branch
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
* tag 'br-v6.2i' of git://linuxtv.org/hverkuil/media_tree: (31 commits)
media: s5c73m3: Switch to GPIO descriptors
media: i2c: s5k5baf: switch to using gpiod API
media: i2c: s5k6a3: switch to using gpiod API
media: imx: remove code for non-existing config IMX_GPT_ICAP
media: si470x: Fix use-after-free in si470x_int_in_callback()
media: staging: stkwebcam: Restore MEDIA_{USB,CAMERA}_SUPPORT dependencies
media: coda: Add check for kmalloc
media: coda: Add check for dcoda_iram_alloc
dt-bindings: media: s5c73m3: Fix reset-gpio descriptor
media: dt-bindings: allwinner: h6-vpu-g2: Add IOMMU reference property
media: s5k4ecgx: Delete driver
media: s5k4ecgx: Switch to GPIO descriptors
media: Switch to use dev_err_probe() helper
headers: Remove some left-over license text in include/uapi/linux/v4l2-*
headers: Remove some left-over license text in include/uapi/linux/dvb/
media: usb: pwc-uncompress: Use flex array destination for memcpy()
media: s5p-mfc: Fix to handle reference queue during finishing
media: s5p-mfc: Clear workbit to handle error condition
media: s5p-mfc: Fix in register read and write for H264
media: imx: Use get_mbus_config instead of parsing upstream DT endpoints
...
The driver has an option to pass in GPIO numbers from platform
data but this is not used in the kernel so delete this. Get
GPIO descriptors using the standard API and simplify the code,
gpiolib will handle any inversions.
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver has an option to pass in GPIO numbers from platform
data but this is not used in the kernel so delete this and the
whole platform data mechanism.
Get GPIO descriptors using the standard API and simplify the code,
gpiolib will handle any inversions.
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Everything is about THS7303, so let the include guard reflect it as well
to avoid potential future conflict.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some devices support sampling of the parallel data at both edges of the
interface pixel clock in order to reduce the pixel clock by two.
Add a mediabus flag that represents this feature.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Previous commit that introduces reference counter does not add proper
comments, which will lead to warning when building htmldocs. Fix them.
Reported-by: "Stephen Rothwell" <sfr@canb.auug.org.au>
Fixes: 0fc044b2b5 ("media: dvbdev: adopts refcnt to avoid UAF")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit 707947247e ("media: videobuf2-vmalloc: get_userptr: buffers are
always writable") caused problems in a corner case (passing read-only
shmem memory as a userptr). So revert this patch.
The original problem for which that commit was originally made is
something that I could not reproduce after reverting it. So just go
back to the way it was for many years, and if problems arise in
the future, then another approach should be taken to resolve it.
This patch is based on a patch from Hirokazu.
Fixes: 707947247e ("media: videobuf2-vmalloc: get_userptr: buffers are always writable")
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
dvb_unregister_device() is known that prone to use-after-free.
That is, the cleanup from dvb_unregister_device() releases the dvb_device
even if there are pointers stored in file->private_data still refer to it.
This patch adds a reference counter into struct dvb_device and delays its
deallocation until no pointer refers to the object.
Link: https://lore.kernel.org/linux-media/20220807145952.10368-1-linma@zju.edu.cn
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Drivers for devices with multiple frontends which cannot be used
concurrently due to hardware limitations which enforce that restriction
by setting the mfe_shared field to 1 exhibit rather unfriendly behavior
towards applications: The unavailable frontend devices cannot be opened
at all, not even for read-only access to query information. Even worse,
any open call is blocked for 5 seconds by default.
Allow drivers for such devices to behave like regular busy frontend
devices instead, i.e. still allowing concurrent read access to the
unavailable frontend and denying concurrent write access with -EBUSY
without delay.
This patch does not alter the behavior of any existing driver to avoid
regressions. Driver developers who wish to take advantage of this must
ensure their driver can handle all read-only accesses to the unavailable
frontend, and indicate the capability by setting the mfe_shared field to
2 instead of 1.
Add a check to dvb-usb-init.c when automatically setting the mfe_shared
field that when a driver has already set the field to 2, it is not
overwritten.
Document the additional capability in the code comment about mfe_shared.
Link: https://lore.kernel.org/linux-media/trinity-22c77578-26b0-4867-9ff7-2668e5d22c64-1642799929896@3c-app-gmx-bap04
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Tested-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When userspace called VIDIOC_STREAMON, then you want to claim any streaming
resources needed and validate the video pipeline. Waiting for
start_streaming to be called is too late, since that can be postponed
until the required minimum of buffers is queued.
So add a prepare_streaming op (optional) that can be used for that
purpose, and a matching unprepare_streaming op (optional) that can
release any claimed resources. The unprepare_streaming op is called
when VIDIOC_STREAMOFF is called and q->streaming is 1, or when the
filehandle is closed while q->streaming is 1.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRSrcquik9wuZrNjXJrQl33mxwedgUCY2U2ZQAKCRBrQl33mxwe
dhaLAP4t7vpFHF6UwPKhUsnBjykDE9cqX5tFY5hV/P4B3dhm3wEAmJFEi38QFQlb
gkISSnYIx5DZGP2iBXT96ftGlPI7qgg=
=wwvs
-----END PGP SIGNATURE-----
Merge tag 'br-v6.2e' of git://linuxtv.org/hverkuil/media_tree into media_stage
Tag branch
* tag 'br-v6.2e' of git://linuxtv.org/hverkuil/media_tree: (29 commits)
media: davinci/vpbe: Fix a typo ("defualt_mode")
media: sun6i-csi: Remove unnecessary print function dev_err()
media: Documentation: Drop deprecated bytesused == 0
media: platform: exynos4-is: fix return value check in fimc_md_probe()
media: dvb-core: remove variable n, turn for-loop to while-loop
media: vivid: fix compose size exceed boundary
media: rkisp1: make const arrays ae_wnd_num and hist_wnd_num static
media: dvb-core: Fix UAF due to refcount races at releasing
media: rkvdec: Add required padding
media: aspeed: Extend debug message
media: aspeed: Support aspeed mode to reduce compressed data
media: Documentation: aspeed-video: Add user documentation for the aspeed-video driver
media: v4l2-ctrls: Reserve controls for ASPEED
media: v4l: Add definition for the Aspeed JPEG format
staging: media: tegra-video: fix device_node use after free
staging: media: tegra-video: fix chan->mipi value on error
media: cedrus: initialize controls a bit later
media: cedrus: prefer untiled capture format
media: cedrus: Remove cedrus_codec enum
media: cedrus: set codec ops immediately
...
Let's spell the variable name correctly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Nothing in the kernel uses the platform data code path.
Drop it, and drop the use of the old legacy <linux/gpio.h>
API in the process.
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Complain in the newly added s_stream video op wrapper if disabling
streaming failed. Also return zero in this case as there's nothing the
caller can do to return the error.
This way drivers also won't need to bother with printing error messages.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Runtime PM has been around for a decade or more, there's hardly a need to
use the V4L2 specific s_power() callback in drivers anymore. Document this
in s_power() callback documentation as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
-----BEGIN PGP SIGNATURE-----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=gJf4
-----END PGP SIGNATURE-----
Merge tag 'media/v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull missed media updates from Mauro Carvalho Chehab:
"It seems I screwed-up my previous pull request: it ends up that only
half of the media patches that were in linux-next got merged in -rc1.
The script which creates the signed tags silently failed due to
5.19->6.0 so it ended generating a tag with incomplete stuff.
So here are the missing parts:
- a DVB core security fix
- lots of fixes and cleanups for atomisp staging driver
- old drivers that are VB1 are being moved to staging to be
deprecated
- several driver updates - mostly for embedded systems, but there are
also some things addressing issues with some PC webcams, in the UVC
video driver"
* tag 'media/v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (163 commits)
media: sun6i-csi: Move csi buffer definition to main header file
media: sun6i-csi: Introduce and use video helper functions
media: sun6i-csi: Add media ops with link notify callback
media: sun6i-csi: Remove controls handler from the driver
media: sun6i-csi: Register the media device after creation
media: sun6i-csi: Pass and store csi device directly in video code
media: sun6i-csi: Tidy up video code
media: sun6i-csi: Tidy up v4l2 code
media: sun6i-csi: Tidy up Kconfig
media: sun6i-csi: Use runtime pm for clocks and reset
media: sun6i-csi: Define and use variant to get module clock rate
media: sun6i-csi: Always set exclusive module clock rate
media: sun6i-csi: Tidy up platform code
media: sun6i-csi: Refactor main driver data structures
media: sun6i-csi: Define and use driver name and (reworked) description
media: cedrus: Add a Kconfig dependency on RESET_CONTROLLER
media: sun8i-rotate: Add a Kconfig dependency on RESET_CONTROLLER
media: sun8i-di: Add a Kconfig dependency on RESET_CONTROLLER
media: sun4i-csi: Add a Kconfig dependency on RESET_CONTROLLER
media: sun6i-csi: Add a Kconfig dependency on RESET_CONTROLLER
...
Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices supported
and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before,
and some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new
chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices
better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different
USB drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BN9g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yljdgCdH4Fev4Nvf2Nokfv0q0krcRB3YpUAn1aZfpb/
EbgxsxhPnTJg+mmXyLms
=IxUy
-----END PGP SIGNATURE-----
Merge tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
-----BEGIN PGP SIGNATURE-----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=MHQ/
-----END PGP SIGNATURE-----
Merge tag 'media/v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New driver for Mediatek MDP V3
- New driver for NXP i.MX DW100 dewarper
- Zoran driver got promoted from staging
- Hantro and related drivers got promoted from staging
- Several VB1 drivers got moved to staging/deprecated (cpia2, fsl-viu,
meye, saa7146, av7110, stkwebcam, tm6000, vpfe_capture, davinci,
zr364xx)
- Usual set of driver fixes, improvements and cleanups
* tag 'media/v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (107 commits)
media: destage Hantro VPU driver
media: platform: mtk-mdp3: add MediaTek MDP3 driver
media: dt-binding: mediatek: add bindings for MediaTek CCORR and WDMA
media: dt-binding: mediatek: add bindings for MediaTek MDP3 components
media: xilinx: vipp: Fix refcount leak in xvip_graph_dma_init
media: xilinx: video: Add 1X12 greyscale format
media: xilinx: csi2rxss: Add 1X12 greyscale format
media: staging: media: imx: imx7-media-csi: Increase video mem limit
media: uvcvideo: Limit power line control for Sonix Technology
media: uvcvideo: Use entity get_cur in uvc_ctrl_set
media: uvcvideo: Fix typo 'the the' in comment
media: uvcvideo: Use indexed loops in uvc_ctrl_init_ctrl()
media: uvcvideo: Fix memory leak in uvc_gpio_parse
media: renesas: vsp1: Add support for RZ/G2L VSPD
media: renesas: vsp1: Add VSP1_HAS_NON_ZERO_LBA feature bit
media: renesas: vsp1: Add support for VSP software version
media: renesas: vsp1: Add support to deassert/assert reset line
media: dt-bindings: media: renesas,vsp1: Document RZ/G2L VSPD bindings
media: meson: vdec: add missing clk_disable_unprepare on error in vdec_hevc_start()
media: amphion: fix a bug that vpu core may not resume after suspend
...
The PCI hybrid card NotOnlyTV LV3H has a built-in IR receiver connected
via I2C bus, currently not supported. This receiver is probably present
in more Geniatech cards. It has no capability for repeating when a key is
held down.
Add support for this built-in IR receiver. Use the existing Total Media
In Hand_02 remote keytable (Geniatech Mygica X8507) which matches exactly
the LV3H remote.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Marek Kidawski <mark_kiddy@wp.pl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that the pipeline is stored into pads instead of entities, we can
change the relevant functions to take pads instead of entities.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a new media entity operation, has_pad_interdep. The optional op is
used to discover the pad interdependencies inside an entity during the
pipeline construction.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
[Note: the code is mostly from Laurent but the patch description is from Tomi]
The media_pipeline_start() and media_pipeline_stop() functions use the
media graph walk API to traverse the graph and validate the pipeline.
The graph walk traverses the media graph following links between the
entities.
Also, while the pipeline can't change between the start and stop calls,
the graph is walked again from scratch at stop time, or any time a
driver needs to inspect the pipeline.
With the upcoming multiplexed streams support we will need a bit more
intelligent pipeline construction, as e.g. two independent streams may
be passing through a single entity via separate pads in which case
those pads should not be part of the same pipeline.
This patch essentially rewrites the media_pipeline_start/stop so that
a pipeline is defined as a set of pads instead of entities and the media
graph traversal considers the pad interdependencies when choosing which
links to follow.
Currently all the entity's pads are considered as interdependent. This
means that the behavior with all the current drivers stays the same, but
in the future we can define a more fine-grained pipeline construction.
Additionally the media pipeline's pads are cached at
media_pipeline_start() time, and re-used at media_pipeline_stop() which
avoid the need to re-walk the whole graph as the previous implementation
did.
Also, caching pads in the pipeline can serve in the future as the
foundation to provide a better API than the media graph walk to drivers
to iterate over pads and entities in the pipeline.
Note that the old media_pipeline_start/stop used the media graph walk
API. The new version does not use the media graph walk API, but instead
a new implementation.
There are two reasons for not changing the graph walk: it proved to be
rather difficult to change the graph walk to have the features
implemented in this patch, and second, this keeps the backward
compatibility of the graph walk as there are users of the graph walk API
The long term plan is that all the existing code would be converted to
use the new cached pipeline, thus allowing us to remove the graph walk.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add new variant of media_pipeline_start(), media_pipeline_alloc_start().
media_pipeline_alloc_start() can be used by drivers that do not need to
extend the media_pipeline. The function will either use the pipeline
already associated with the entity, if such exists, or allocate a new
pipeline.
When media_pipeline_stop() is called and the pipeline's use count drops
to zero, the pipeline is automatically freed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
With the upcoming stream related improvements to the pipelines, the
pipelines are moved from media entities to media pads. As the drivers
currently use the pipelines with the entity based model, moving the
pipelines to pads will cause changes to the drivers.
However, most of the uses of media pipelines are related to a video
device (a DMA engine) with a single pad, and thus there's never a need
to support multiple pads in these use cases. We can avoid pushing the
complexities of the pad based model to the drivers by adding video
device wrappers for the pipeline related functions.
This patch adds a number of wrappers to media_pipeline functions, all of
which take a video_device as a parameter (instead of a media_entity),
and verify that there's just one pad.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace direct access to the pipe field in drivers with a new helper
function. This will allow easier refactoring of media pipeline handling
in the MC core behind the scenes without affecting drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media_entity_enum_init() function is a wrapper around
__media_entity_enum_init() that turns a media_device pointer argument
into the maximum entity ID in the corresponding media graph.
__media_entity_enum_init() is never used outside of
media_entity_enum_init(), so the two functions can be merged together.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add an iterator helper to easily cycle through all pads in an entity and
use it in media-entity and media-device code where appropriate.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
'streaming_count' is a bit misleading name, as the count is increased
with media_pipeline_start(). Let's rename it to 'start_count' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
V4L2_FRAME_DESC_ENTRY_MAX is currently set to 4. In theory it's possible
to have an arbitrary amount of streams in a single pad, so preferably
there should be no hardcoded maximum number.
However, I believe a reasonable max is 8, which would cover a CSI-2 pad
with 4 streams of pixel data and 4 streams of metadata.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
./include/media/media-entity.h:595:34: error: implicit declaration of function ‘min’
Include minmax.h to get the definition for min().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
struct v4l2_fwnode_endpoint was zeroed previously apart from the endpoint
information itself when the endpoint properties were parsed. Now this
hasn't been the case for a few years so remove the comment.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The state argument for the functions for obtaining various parts of the
state is NULL if it is called by drivers for active state. Fail graciously
in that case instead of dereferencing a NULL pointer.
Suggested-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The doc says the I²C device's name is used if devname is NULL, but
actually the I²C device driver's name is used.
Fixes: 0658293012 ("media: v4l: subdev: Add a function to set an I²C sub-device's name")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The type ops for equal, init and validate have an elems argument,
but this can be taken from struct v4l2_ctrl: ctrl->elems for
equal and init, and ctrl->new_elems for validate (since you are
validating a new control value).
So drop this argument and update all callers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The uvc_format_desc, GUID defines and the uvc_format_by_guid helper is
also useful for the uvc gadget stack. This patch moves them to a common
header.
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220909221335.15033-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions uvc_simplify_fraction and uvc_fraction_to_interval are
generic helpers which are also useful for other v4l2 drivers. This patch
moves them to v4l2-common.
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220909221335.15033-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support DRM blend mode in R-Car DU driver, we must be able to pass
a plane with the premultiplied alpha. Adding a new property to
vsp1_du_atomic_config allows the R-Car DU driver to pass the
premultiplied alpha plane.
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that we've transitioned all users to vb2_find_buffer API,
remove the unused vb2_find_timestamp().
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Deprecate the hexium_gemini, hexium_orion, mxb and ttpci saa7146-based
drivers: these drivers do not use the vb2 framework for video streaming,
instead it uses the old videobuf framework.
We want to get rid of these old drivers, so deprecated these for future
removal.
[hverkuil: update MAINTAINERS file]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Deprecate the dm644x_ccdc, dm355_cddc and dm365_isif davinci drivers:
all three depend on the vpfe_capture driver, and that driver does not
use the vb2 framework for video streaming, instead it uses the old
videobuf framework.
We want to get rid of these old drivers, so deprecated these for future
removal.
Note that include/media/davinci/vpfe_capture.h can't be moved to staging
since it is used in arch/arm/mach-davinci/davinci.h.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
These terms typically refer to the old version 1 videobuf framework.
It is confusing to use them for the vb2 framework, so reword these
comments.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It is confusing to refer to vb2 structures with 'videobuf', since
that typically is used to refer to the old videobuf version 1
framework.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It is confusing to use the term 'videobuf' or 'video-buf' since that
usually refers to the old videobuf version 1 framework. Rename to
'videobuf2' or vb2.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Export the callback functions of the default v4l2 control type operations
such as a driver defining its own operations could reuse some of them.
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initializing arrays and validating or checking for equality of arrays
is suboptimal since it does this per element.
Change the ops to operate on the whole payload to speed up array
operations.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a new function to modify the dimensions of an array control.
This is typically used if the array size depends on e.g. the currently
selected video format.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Also allocate space for arrays in struct ctrl_ref.
This is in preparation for allowing to change the array size from
a driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Just like dynamic arrays, also allocate space for regular arrays.
This is in preparation for allowing to change the array size from
a driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
The newly added media_entity_remote_source_pad_unique() helper function
handles use cases where the entity has a link enabled uniqueness
constraint covering all pads. There are use cases where the constraint
covers a specific pad only. Add a new media_pad_remote_pad_unique()
function to handle this. It operates as
media_entity_remote_source_pad_unique(), but on a given pad instead of
on the entity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media_entity_remote_pad_first() helper function returns the first
remote pad it finds connected to a given pad. Beside being possibly
non-deterministic (as it stops at the first enabled link), the fact that
it returns the first match makes it unsuitable for drivers that need to
guarantee that a single link is enabled, for instance when an entity can
process data from one of multiple sources at a time.
For those use cases, add a new helper function,
media_entity_remote_pad_unique(), that operates on an entity and returns
a remote pad, with a guarantee that only one link is enabled. To ease
its use in drivers, also add an inline wrapper that locates source pads
specifically. A wrapper that locates sink pads can easily be added when
needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media_entity_remote_pad() is misnamed, as it operates on a pad and
not an entity. Rename it to media_pad_remote_pad_first() to clarify its
behaviour.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Drivers typically extend the v4l2_async_subdev structure by embedding it
in a driver-specific structure, to store per-subdev custom data. The
v4l2_async_subdev instances are freed by the v4l2-async framework, which
makes this mechanism cumbersome to use safely when custom data needs
special treatment to be destroyed (such as freeing additional memory, or
releasing references to kernel objects).
To ease this, add a .destroy() operation to the
v4l2_async_notifier_operations structure. The operation is called right
before the v4l2_async_subdev is freed, giving drivers a chance to
destroy data if needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
All users of vb2_find_timestamp() combine it with vb2_get_buffer()
to retrieve a videobuf2 buffer, given a u64 timestamp.
Introduce an API for this use-case. Users will be converted to the new
API as follow-up commits.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
HEVC uAPI is used by 2 mainline drivers (Hantro, Cedrus)
and at least 2 out-of-tree drivers (rkvdec, RPi).
The uAPI has been reviewed so it is time to make it 'public' by
un-staging it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
'F.7.3.6.1 General slice segment header syntax' section of HEVC
specification describes that a slice header always end aligned on
byte boundary, therefore we only need to provide the data offset in bytes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The number of bits to skip in the slice header can be computed
in the driver by using sps, pps and decode_params information.
This makes it possible to remove Hantro dedicated control.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move HEVC pixel format since we are ready to stabilize the uAPI
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The number of 'entry point offset' can be very variable.
Instead of using a large static array define a v4l2 dynamic array
of U32 (V4L2_CTRL_TYPE_U32).
The number of entry point offsets is reported by the elems field
and in struct v4l2_ctrl_hevc_slice_params.num_entry_point_offsets
field.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make explicit that V4L2_CID_STATELESS_HEVC_SLICE_PARAMS control is
a dynamic array control type.
Some drivers may be able to receive multiple slices in one control
to improve decoding performance.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The possible values for the field_pic field in the v4l2_hevc_dpb_entry
structure are defined in the table D.2 in HEVC specification section D.3.3.
Add flags and documentation for each of them.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The HEVC specification describes the following:
"PicOrderCntVal is derived as follows:
PicOrderCntVal = PicOrderCntMsb + slice_pic_order_cnt_lsb
The value of PicOrderCntVal shall be in the range of
−2^31 to 2^31 − 1, inclusive."
To match with these definitions change __u16 pic_order_cnt[2]
into __s32 pic_order_cnt_val.
Change v4l2_ctrl_hevc_slice_params->slice_pic_order_cnt to __s32 too.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Complete the HEVC controls with missing fields from H.265 specifications.
Even if these fields aren't used by the current mainlined drivers
they will be required for (at least) the rkvdec driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement support for dynamically allocated arrays.
Most of the changes concern keeping track of the number of elements
of the array and the number of elements allocated for the array and
reallocating memory if needed.
Acked-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Iterating over the links for an entity is a somewhat common need
through the media subsystem, but generally the assumption is that
they will all be data links. To meet that assumption add a new macro
that iterates through an entity's links and skips non-data links.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a helper macro for the situations where a non-MC driver needs to
call a state-operation (operation which takes a subdev state as a
parameter) in try-context in another subdev.
The macro allocates a new subdev state for the called subdev and frees
the state afterwards.
An example use case is a media platform driver testing if a
v4l2_subdev_format would be accepted by a source subdev.
This should not be used in MC drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The helper functions that test validity of colorspace-related fields
use the last value of the corresponding enums. This isn't very
future-proof, as there's a high chance someone adding a new value may
forget to update the helpers. Add new "LAST" entries to the enumerations
to improve this, and keep them private to the kernel.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This inserts 4 pixels of the RGB color 0xab55ab at the left hand side of
the image. This is only done for 3 or 4 byte RGB pixel formats. The HDMI
TMDS encoding of this pixel value equals the Video Guard Band value as
defined by HDMI (see section 5.2.2.1 in the HDMI 1.3 Specification) that
preceeds the first actual pixel of a video line. If an HDMI receiver
doesn't handle this correctly, then it might keep skipping these Video
Guard Band patterns and end up with a shorter video line. So this is a
nice pattern to test with.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Based on the normalized pattern:
this program is free software you may redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 of the license the software is
provided as is without warranty of any kind express or implied
including but not limited to the warranties of merchantability fitness
for a particular purpose and noninfringement in no event shall the
authors or copyright holders be liable for any claim damages or other
liability whether in an action of contract tort or otherwise arising
from out of or in connection with the software or the use or other
dealings in the software
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the reference list builder, frame_num refers to FrameNumWrap
in the spec, which is the same as the pic_num for frame decoding.
The same applies for long_term_pic_num and long_term_frame_idx.
Sort all type of references by frame_num so the sort can be reused
for fields reflist were the sorting is done using frame_num instead.
In short, pic_num is never actually used for building reference
lists.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the current picture is a field, store each field into the
unordered_list and preserve both top and bottom picture order
count.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This information, also called picture structure, is required in field
decoding mode to construct reference lists.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is to accommodate support for field decoding, which splits the top
and the bottom references into the reference list.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In preparation for adding field decoding support, convert the byte arrays
for reflist into array of struct v4l2_h264_reference. That struct will
allow us to mark which field of the reference picture is being referenced.
[hverkuil: top_field_order_cnt -> pic_order_count]
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add CSI-2 data type for 28 bits per pixel data.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add CSI-2 bus specific configuration to the frame descriptors. This allows
obtaining the virtual channel and data type information for each stream
the transmitter is sending.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the media bus type to the frame descriptor. CSI-2 specific
information will be added in next patch to the frame descriptor.
- Make the bus type a named enum
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As V4L2_FWNODE_BUS_TYPE_PARALLEL is not used for DPI interface, this
patch add V4L2_FWNODE_BUS_TYPE_DPI for video DPI interface.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Using an activation counter to decide when the enable or disable the
cec adapter is not the best approach and can lead to race conditions.
Change this to determining the current status of the adapter, and
enable or disable the adapter accordingly.
It now only needs to be called whenever there is a chance that the
state changes, and it can handle enabling/disabling monitoring as
well if needed.
This simplifies the code and it should be a more robust approach as well.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the physical address changes (i.e. becomes invalid, then valid again)
while the adapter is still claiming free logical addresses, then trigger
a reconfiguration since any claimed LAs may now be stale.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
vb2 queue ownership is managed by the ioctl handler helpers
(vb2_ioctl_*). There are however use cases where drivers can benefit
from checking queue ownership, for instance when open-coding an ioctl
handler that needs to perform additional checks before calling the
corresponding vb2 operation.
Expose the vb2_queue_is_busy() function in the videobuf2-v4l2.h header,
and change its first argument to a struct vb2_queue pointer as the
function name implies it operates on a queue, not a video_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The documentation comment was inserted between the return type
and the function name. Reunite the lines.
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Fixes: db7ee32aa1 ("[media] media-device.h: Improve documentation and update it")
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For spdx, remove leading space
Replacements
parametrize to parameterize
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add v4l2_subdev_get_fmt() helper function which implements
v4l2_subdev_pad_ops.get_fmt using active state. Subdev drivers that
support active state and do not need to do anything special in their
get_fmt op can use this helper directly for v4l2_subdev_pad_ops.get_fmt.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The V4L2 subdevs have managed without centralized locking for the state
(previously pad_config), as the try-state is supposedly safe (although I
believe two TRY ioctls for the same fd would race), and the
active-state, and its locking, is managed by the drivers internally.
We now have active-state in a centralized position, and need locking.
Strictly speaking the locking is only needed for new drivers that use
the new state, as the current drivers continue behaving as they used to.
However, active-state locking is complicated by the fact that currently
the real active-state of a subdev is split into multiple parts: the new
v4l2_subdev_state, subdev control state, and subdev's internal state.
In the future all these three states should be combined into one state
(the v4l2_subdev_state), and then a single lock for the state should be
sufficient.
But to solve the current split-state situation we need to share locks
between the three states. This is accomplished by using the same lock
management as the control handler does: we use a pointer to a mutex,
allowing the driver to override the default mutex. Thus the driver can
do e.g.:
sd->state_lock = sd->ctrl_handler->lock;
before calling v4l2_subdev_init_finalize(), resulting in sharing the
same lock between the states and the controls.
The locking model for active-state is such that any subdev op that gets
the state as a parameter expects the state to be already locked by the
caller, and expects the caller to release the lock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The subdev state is now used for both try and active cases. Rename
rename v4l2_subdev_get_try_* helpers to v4l2_subdev_get_pad_*.
Temporary wapper helper macros are added to keep the drivers using
v4l2_subdev_get_try_* compiling. The next step is to change the uses
in th drivers, and then drop the helpers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a new 'active_state' field to struct v4l2_subdev to which we can
store the active state of a subdev. This will place the subdev
configuration into a known place, allowing us to use the state directly
from the v4l2 framework, thus simplifying the drivers.
Also add functions v4l2_subdev_init_finalize() and
v4l2_subdev_cleanup(), which will allocate and free the active state.
The functions are named in a generic way so that they can be also used
for other subdev initialization work.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l2_subdev_alloc_state() and v4l2_subdev_free_state() are not supposed
to be used by the drivers. However, we do have a few drivers that use
those at the moment, so we need to expose these functions for the time
being.
Prefix the functions with __ to mark the functions as internal.
At the same time, rename them to v4l2_subdev_state_alloc and
v4l2_subdev_state_free to match the style used for other functions like
video_device_alloc() and media_request_alloc().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add comments after #endifs to clarify their scope.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set bus_info field based on struct device in media_device_init() and
remove corresponding code from drivers.
Also update media_device_init() documentation: the dev field must be now
initialised before calling it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The bus_info or a similar field exists in a lot of structs, yet drivers
tend to set the value of that field by themselves in a determinable way.
Thus provide a helper for doing this. To be used in subsequent patches.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The documentation for media_device_init() had several references to
(struct) media_entity where it should have referred to struct media_device
instead. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove redundant kerneldoc documentation in mc-device.c. The functions are
already documented in media-device.h, where non-redundant documentation is
also moved.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add functions to create ancillary links, so that they don't need to
be manually created by users.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This new optional callback is called when the adapter is fully configured
or fully unconfigured. Some drivers may have to take action when this
happens.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allow drivers to change the transmit timeout value, i.e. after how
long should a transmit be considered 'lost', i.e. the corresponding
cec_transmit_done_ts was never called.
Some CEC devices have their own timeout, and so this timeout value must be
longer than that hardware timeout value. If it is shorter then the
framework would consider the transmit lost, even though it is effectively
still in progress at the hardware level.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a transmit-in-progress was canceled, then, once the transmit
is done, mark it as aborted and refrain from retrying the transmit.
To signal this situation the new transmit_in_progress_aborted field is
set to true.
The old implementation would just set adap->transmitting to NULL and
set adap->transmit_in_progress to false, but on the hardware level
the transmit was still ongoing. However, the framework would think
the transmit was aborted, and if a new transmit was issued, then
it could overwrite the HW buffer containing the old transmit with the
new transmit, leading to garbled data on the CEC bus.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't enable/disable the adapter if the first fh is opened or the
last fh is closed, instead do this when the adapter is configured
or unconfigured, and also when we enter Monitor All or Monitor Pin
mode for the first time or we exit the Monitor All/Pin mode for the
last time.
However, if needs_hpd is true, then do this when the physical
address is set or cleared: in that case the adapter typically is
powered by the HPD, so it really is disabled when the HPD is low.
This case (needs_hpd is true) was already handled in this way, so
this wasn't changed.
The problem with the old behavior was that if the HPD goes low when
no fh is open, and a transmit was in progress, then the adapter would
be disabled, typically stopping the transmit immediately which
leaves a partial message on the bus, which isn't nice and can confuse
some adapters.
It makes much more sense to disable it only when the adapter is
unconfigured and we're not monitoring the bus, since then you really
won't be using it anymore.
To keep track of this store a CEC activation count and call adap_enable
only when it goes from 0 to 1 or back to 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Fujitsu M5MOLS sensor driver is using a reset GPIO number
passed from platform data.
No machine/board descriptor file in the kernel is using this so
let's replace it with a GPIO descriptor.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The noon010pc30 sensor driver is using legacy gpio numbers passed
through platform data and open coding reverse polarity on the
GPIOs used for reset and standby.
Nothing in the kernel defines any platform data for this driver
so we can just convert the driver to use GPIO descriptors and
requires that these specify the correct polarity instead.
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Being able to call cleanup functions on objects that haven't been
initialized but whose memory has been zeroed simplifies error handling.
The media_entity_cleanup() function documentation doesn't tell whether
this is allowed or not, and inspection of its implementation doesn't
provide any clue as the function is currently empty. Update the
documentation to explicitly allow this usage pattern.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The media_pipeline_start() function has two purposes: it constructs a
pipeline by recording the entities that are part of it, gathered from a
graph walk, and validate the media links. The pipeline pointer is stored
in the media_entity structure as part of this process, and the entity's
stream count is increased, to record that the entity is streaming.
When multiple video nodes are present in a pipeline,
media_pipeline_start() is typically called on all of them, with the same
pipeline pointer. This is taken into account in media_pipeline_start()
by skipping validation for entities that are already part of the
pipeline, while returning an error if an entity is part of a different
pipeline.
It turns out that this process is overly complicated. When
media_pipeline_start() is called for the first time, it constructs the
full pipeline, adding all entities and validating all the links.
Subsequent calls to media_pipeline_start() are then nearly no-ops, they
only increase the stream count on the pipeline and on all entities.
The media_entity stream_count field is used for two purposes: checking
if the entity is streaming, and detecting when a call to
media_pipeline_stop() balances needs to reset the entity pipe pointer to
NULL. The former can easily be replaced by a check of the pipe pointer.
Simplify media_pipeline_start() by avoiding the pipeline walk on all
calls but the first one, and drop the media_entity stream_count field.
media_pipeline_stop() is updated accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Sakari Ailus: Drop redundant '!= NULL' as discussed]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Add a function to test if a pad is part of a pipeline currently
streaming, and use it through drivers to replace direct access to the
stream_count field. This will help reworking pipeline start/stop without
disturbing drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
There are many CSI-2-related drivers in the media subsystem that come
with their own macros to handle the CSI-2 data types (or just hardcode
the numerical values). Provide a shared header with definitions for
those data types that driver can use.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MIPI CSI-2 continuous and non-continuous clock modes are mutually
exclusive. Drop the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag and use
V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The V4L2_MBUS_CSI2_CHANNEL_* flags are a legacy API. Only
V4L2_MBUS_CSI2_CHANNEL_0 is used, set in a single driver, and never
read. Drop those flags. Virtual channel information should be conveyed
through frame descriptors instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The V4L2_MBUS_CSI2_*_LANE flags are a legacy API and are unused. Drop
them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media bus configuration is specified through a set of flags, some of
which being mutually exclusive. This doesn't scale to express more
complex configurations. Improve the API by replacing the single flags
field in v4l2_mbus_config by a union of v4l2_mbus_config_* structures.
The flags themselves are still used in those structures, so they are
kept here. Drivers are however updated to use structure fields instead
of flags when already possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver report a reset event when the hardware reports and overflow.
There is no reason to have a generic "reset" event.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To prepare for usage of the v4l2_fwnode_bus_* data structures to
describe bus configuration in the subdev .get_mbus_config() operation,
rename the structures with a v4l2_mbus_config_ prefix instead of
v4l2_fwnode_bus_, and move them to v4l2_mediabus.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The .set_mbus_config() operation is deprecated, and nothing in the
kernel uses it. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When a driver reports a timeout, no more IR activity will be reported
until the next pulse. A space is inserted between the timeout and the
next pulse, based on ktime.
The timeout reports already a duration, so this duration should not be
added to the gap. Otherwise there is no change to the functionality.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Marking a picture as long-term reference is valid for DPB but not for RPS.
Change flag name to match with the description in HEVC spec chapter
"8.3.2 Decoding process for reference picture set".
PocStCurrBefore, PocStCurrAfter, PocLtCurr lists could be built by the
kernel from the DPB entries struct v4l2_hevc_dpb_entry, using the
information in the rps field. This way RPS flags becomes useless and are
removed.
This patch breaks the staging HEVC API because it introduces a new flag,
changes a field name in v4l2_hevc_dpb_entry structure and removes
V4L2_HEVC_DPB_ENTRY_RPS_* flags.
[hverkuil: fixed some typos]
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Without timeout reports, it is impossible to decode many protocols since
it is not known when the transmission ends. timeout reports are sent by
default, but can be turned off. There is no reason to turn them off, and
I cannot find any software which does this, so we can safely remove it.
This makes the ioctl LIRC_SET_REC_TIMEOUT_REPORTS a no-op.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In function vb2_set_plane_payload, report if the given bytesused is
bigger than the buffer size, and clamp it to the buffer size.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cec_devnode struct has a lock meant to serialize access
to the fields of this struct. This lock is taken during
device node (un)registration and when opening or releasing a
filehandle to the device node. When the last open filehandle
is closed the cec adapter might be disabled by calling the
adap_enable driver callback with the devnode.lock held.
However, if during that callback a message or event arrives
then the driver will call one of the cec_queue_event()
variants in cec-adap.c, and those will take the same devnode.lock
to walk the open filehandle list.
This obviously causes a deadlock.
This is quite easy to reproduce with the cec-gpio driver since that
uses the cec-pin framework which generated lots of events and uses
a kernel thread for the processing, so when adap_enable is called
the thread is still running and can generate events.
But I suspect that it might also happen with other drivers if an
interrupt arrives signaling e.g. a received message before adap_enable
had a chance to disable the interrupts.
This patch adds a new mutex to serialize access to the fhs list.
When adap_enable() is called the devnode.lock mutex is held, but
not devnode.lock_fhs. The event functions in cec-adap.c will now
use devnode.lock_fhs instead of devnode.lock, ensuring that it is
safe to call those functions from the adap_enable callback.
This specific issue only happens if the last open filehandle is closed
and the physical address is invalid. This is not something that
happens during normal operation, but it does happen when monitoring
CEC traffic (e.g. cec-ctl --monitor) with an unconfigured CEC adapter.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v5.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Provide code common to vp9 drivers in one central location.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the VP9 stateless decoder controls plus the documentation that goes
with it.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Co-developed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Co-developed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While dvb_tuner_ops already has dedicated suspend and resume callbacks,
dvb_frontend_ops currently does not have them. Add those callbacks and
use them for suspend and resume. If they are not set, the old behavior
of calling sleep or init is used.
This allows dvb_frontend drivers to handle resume differently from init,
and suspend differently from sleep. No change is required for drivers
not needing this functionality.
Link: https://lore.kernel.org/linux-media/20210418001204.7453-2-kernel@tuxforce.de
Cc: Lukas Middendorf <kernel@tuxforce.de>, Antti Palosaari <crope@iki.fi>, Mauro Carvalho Chehab <mchehab@kernel.org>, Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Lukas Middendorf <kernel@tuxforce.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For platforms without MMU the m2m provides a helper method
v4l2_m2m_get_unmapped_area(), The mmap() routines will call
this to get a proposed address for the mapping.
More detailed information about get_unmapped_area can be found in
Documentation/nommu-mmap.txt
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Merge more updates from Andrew Morton:
"87 patches.
Subsystems affected by this patch series: mm (pagecache and hugetlb),
procfs, misc, MAINTAINERS, lib, checkpatch, binfmt, kallsyms, ramfs,
init, codafs, nilfs2, hfs, crash_dump, signals, seq_file, fork,
sysvfs, kcov, gdb, resource, selftests, and ipc"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (87 commits)
ipc/ipc_sysctl.c: remove fallback for !CONFIG_PROC_SYSCTL
ipc: check checkpoint_restore_ns_capable() to modify C/R proc files
selftests/kselftest/runner/run_one(): allow running non-executable files
virtio-mem: disallow mapping virtio-mem memory via /dev/mem
kernel/resource: disallow access to exclusive system RAM regions
kernel/resource: clean up and optimize iomem_is_exclusive()
scripts/gdb: handle split debug for vmlinux
kcov: replace local_irq_save() with a local_lock_t
kcov: avoid enable+disable interrupts if !in_task()
kcov: allocate per-CPU memory on the relevant node
Documentation/kcov: define `ip' in the example
Documentation/kcov: include types.h in the example
sysv: use BUILD_BUG_ON instead of runtime check
kernel/fork.c: unshare(): use swap() to make code cleaner
seq_file: fix passing wrong private data
seq_file: move seq_escape() to a header
signal: remove duplicate include in signal.h
crash_dump: remove duplicate include in crash_dump.h
crash_dump: fix boolreturn.cocci warning
hfs/hfsplus: use WARN_ON for sanity check
...
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
Link: https://lkml.kernel.org/r/20211013170417.87909-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Brendan Higgins <brendanhiggins@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The open brace should be after a struct of define, that's good
for searching.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Preparations for future V4L2_MEMORY_FLAG_NON_COHERENT support.
Extend the vb2_core_reqbufs() parameters list to accept requests'
->flags, which will be used for memory coherency configuration.
An attempt to allocate a buffer with coherency requirements
that do not match the queue's consistency model will fail.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It would be less error prone if the default cache hints value
(we kzalloc() structs, so it's zeroed out by default) would be
to "always sync/flush" caches. Inverse and rename cache hints
flags.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With the new DMA API we need an extension of the videobuf2 API.
Previously, videobuf2 core would set the non-coherent DMA bit
in the vb2_queue dma_attr field (if user-space would pass a
corresponding memory hint); the vb2 core then would pass the
vb2_queue dma_attrs to the vb2 allocators. The vb2 allocator
would use the queue's dma_attr and the DMA API would allocate
either coherent or non-coherent memory.
But we cannot do this anymore, since there is no corresponding DMA
attr flag and, hence, there is no way for the allocator to become
aware of what type of allocation user-space has requested. So we
need to pass more context from videobuf2 core to the allocators.
Fix this by changing the call_ptr_memop() macro to pass the
vb2 pointer to the corresponding op callbacks.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
HEVC scaling lists are used for the scaling process for transform
coefficients.
V4L2_HEVC_SPS_FLAG_SCALING_LIST_ENABLED has to set when they are
encoded in the bitstream.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Evaluate the desired pixel clock polarity from the device tree.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename V4L2 async notifier functions, replacing "notifier" with "nf" and
removing "_subdev" at the end of the function names adding subdevs as you
can only add subdevs to a notifier. Also wrap and otherwise clean up long
lines.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> (imx7)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add pre_streamon and post_streamoff callbacks that can be used to set a
CSI-2 transmitter to LP-11 or LP-111 mode. This can be used by receiver
drivers to reliably initialise the receiver when its initialisation
requires software involvement.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix kerneldoc syntax in v4l2-async. The references were not produced
correctly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the name of the function that registers the subdev_notifier member
of the v4l2_subdev structure.
[Sakari Ailus: Drop _sensor from the function name.]
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The s_learning_mode() function is called in response to the ioctl
LIRC_SET_WIDEBAND_RECEIVER, so rename it to s_wideband_receiver().
Learning mode is when both the wideband receiver is turned on and
carrier reports are enabled.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Any timeout larger than LIRC_VALUE_MASK cannot work for the lirc uapi.
LIRC_VALUE_MASK is about 16 seconds which is more than enough.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If HEVC frame consists of multiple slices, segment address has to be
known in order to properly decode it.
Add segment address field to slice parameters.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add Geniatech MyGica T230C2_LITE and T230A as many people
are asking support for these devices on forums.
Link: https://lore.kernel.org/linux-media/YMuptIYFLdwSmw//@kali
Signed-off-by: Ján Čáni <pego149@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Smatch static checker warns that "mdev" can be null:
sound/usb/media.c:287 snd_media_device_create()
warn: 'mdev' can also be NULL
If CONFIG_MEDIA_CONTROLLER is disabled, this file should not be included
in the build.
The below conditions in the sound/usb/Makefile are in place to ensure that
media.c isn't included in the build.
sound/usb/Makefile:
snd-usb-audio-$(CONFIG_SND_USB_AUDIO_USE_MEDIA_CONTROLLER) += media.o
select SND_USB_AUDIO_USE_MEDIA_CONTROLLER if MEDIA_CONTROLLER &&
(MEDIA_SUPPORT=y || MEDIA_SUPPORT=SND_USB_AUDIO)
The following config check in include/media/media-dev-allocator.h is
in place to enable the API only when CONFIG_MEDIA_CONTROLLER and
CONFIG_USB are enabled.
#if defined(CONFIG_MEDIA_CONTROLLER) && defined(CONFIG_USB)
This check doesn't work as intended when CONFIG_USB=m. When CONFIG_USB=m,
CONFIG_USB_MODULE is defined and CONFIG_USB is not. The above config check
doesn't catch that CONFIG_USB is defined as a module and disables the API.
This results in sound/usb enabling Media Controller specific ALSA driver
code, while Media disables the Media Controller API.
Fix the problem requires two changes:
1. Change the check to use IS_ENABLED to detect when CONFIG_USB is enabled
as a module or static. Since CONFIG_MEDIA_CONTROLLER is a bool, leave
the check unchanged to be consistent with drivers/media/Makefile.
2. Change the drivers/media/mc/Makefile to include mc-dev-allocator.o
in mc-objs when CONFIG_USB is enabled.
Link: https://lore.kernel.org/alsa-devel/YLeAvT+R22FQ%2FEyw@mwanda/
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The saa6588_ioctl() function expects to get called from other kernel
functions with a 'saa6588_command' pointer, but I found nothing stops it
from getting called from user space instead, which seems rather dangerous.
The same thing happens in the davinci vpbe driver with its VENC_GET_FLD
command.
As a quick fix, add a separate .command() callback pointer for this
driver and change the two callers over to that. This change can easily
get backported to stable kernels if necessary, but since there are only
two drivers, we may want to eventually replace this with a set of more
specialized callbacks in the long run.
Fixes: c3fda7f835 ("V4L/DVB (10537): saa6588: convert to v4l2_subdev.")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.
I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.
This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.
The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:
dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done
Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:
For drivers/media/i2c/s5k5baf.c:
@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;
For drivers/media/platform/s3c-camif/camif-capture.c:
@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;
The semantic patch is:
// <smpl>
// Change function parameter
@@
identifier func;
identifier cfg;
@@
func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}
// Change function declaration parameter
@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);
// Change function return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}
// Change function declaration return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);
// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.
@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };
<+...
(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)
...+>
}
// If the function uses fields from pad_config, access via state->pads
@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}
// If the function accesses the filehandle, use fh->state instead
@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state
@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state
// Start of vsp1 specific
@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};
@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}
@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}
@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}
// End of vsp1 specific
// Start of rcar specific
@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
// End of rcar specific
// Start of rockchip specific
@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}
@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}
@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@
rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}
// End of rockchip specific
// Start of tegra-video specific
@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}
// End of tegra-video specific
// </smpl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HEVC HANTRO driver needs to know the number of bits to skip at
the beginning of the slice header.
That is a hardware specific requirement so create a dedicated control
for this purpose.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add decode params control and the associated structure to group
all the information that are needed to decode a reference frame as
is described in ITU-T Rec. H.265 section "8.3.2 Decoding process
for reference picture set".
Adapt Cedrus driver to these changes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add fields and flags as they are defined in
7.4.3.3.1 "General picture parameter set RBSP semantics of the
H.265 ITU specification.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is an NEC remote control device shipped with some Toshiba TVs.
Signed-off-by: Alexander Voronov <avv.0@ya.ru>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
sps_max_sub_layers_minus1 is needed if the driver wishes to determine
whether or not a frame might be used for reference.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some platforms a video device can capture either video data or
metadata. The driver can implement vidioc functions for both video and
metadata, and use a single vb2_queue for the buffers. However, vb2_queue
requires choosing a single buffer type, which conflicts with the idea of
capturing either video or metadata.
The buffer type of vb2_queue can be changed, but it's not obvious how
this should be done in the drivers. To help this, add a new helper
function vb2_queue_change_type() which ensures the correct checks and
documents how it can be used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Until now, the MPEG-2 V4L2 API was not exported as a public API,
and only defined in a private media header (media/mpeg2-ctrls.h).
After reviewing the MPEG-2 specification in detail, and reworking
the controls so they match the MPEG-2 semantics properly,
we can consider it ready.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the MPEG-2 stateless control types out of staging,
and re-number it to avoid any confusion.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Hantro and Cedrus drivers work in frame-mode,
meaning they expect all the slices in a picture (either frame
or field structure) to be passed in each OUTPUT buffer.
These two are the only V4L2 MPEG-2 stateless decoders currently
supported. Given the VA-API drivers also work per-frame,
coalescing all the MPEG-2 slices in a buffer before the decoding
operation, it makes sense to not expect slice-mode drivers and
therefore remove V4L2_CID_MPEG_VIDEO_MPEG2_SLICE_PARAMS.
This is done to avoid carrying an unused interface. If needed,
this control can be added without breaking backwards compatibility.
Note that this would mean introducing a enumerator control to
specify the decoding mode (see V4L2_CID_STATELESS_H264_DECODE_MODE).
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The forward and backwards references are specified per-picture
and not per-slice. Move it to V4L2_CID_MPEG_VIDEO_MPEG2_PICTURE.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Typically, bitstreams are composed of a sequence header,
followed by a number of picture header and picture coding extension
headers. Each picture can be composed of a number of slices.
Let's split the MPEG-2 uAPI to follow these semantics more closely,
allowing more usage flexibility. Having these controls split up
allows applications to set a sequence control at the beginning
of a sequence, and then set a picture control for each frame.
While here add padding fields where needed, and document
the uAPI header thoroughly.
Note that the V4L2_CTRL_TYPE_{} defines had to be moved because
it clashes with existing ones. This is not really an issue
since they will be re-defined when the controls are moved
out of staging.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Our current MPEG-2 uAPI uses 1-byte fields for MPEG-2
boolean syntax elements. Clean these by adding a 'flags'
field and flag macro for each boolean syntax element.
A follow-up change will refactor this uAPI so we don't need
to add padding fields just yet.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As stated in the MPEG-2 specification, section 6.3.7 "Quant matrix
extension":
Each quantisation matrix has a default set of values. When a
sequence_header_code is decoded all matrices shall be reset to
their default values. User defined matrices may be downloaded
and this can occur in a sequence_header() or in a
quant_matrix_extension().
The load_intra_quantiser_matrix syntax elements are transmitted
in the bitstream headers, signalling that a quantisation matrix
needs to be loaded and used for pictures transmitted afterwards
(until the matrices are reset).
This "load" semantics are implemented in the V4L2 interface
without the need of any "load" flags: passing the control
is effectively a load.
Therefore, rework the V4L2_CID_MPEG_VIDEO_MPEG2_QUANTISATION
semantics to match the MPEG-2 semantics. Quantisation matrices
values are now initialized by the V4L2 control core to their
reset default value, and applications are expected to reset
their values as specified.
The quantisation control is therefore optional, and used to
load bitstream-defined values in the quantisation matrices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MPEG-2 specification refers to the quantisation matrices
using the word "quantisation". Make the V4L2 interface more
ergonomic by matching the MPEG-2 spec.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The tango platform was removed, so the driver is no longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dependent slice segment flag for PPS control is misnamed. It should have
"enabled" at the end. It only tells if this flag is present in slice
header or not and not the actual value.
Fix this by renaming the PPS flag and introduce another flag for slice
control which tells actual value.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When controls are used together with the Request API, then for
each request a v4l2_ctrl_handler struct is allocated. This contains
the controls that can be set in a request. If a control is *not* set in
the request, then the value used in the most recent previous request
must be used, or the current value if it is not found in any outstanding
requests.
The framework tried to find such a previous request and it would set
the 'req' pointer in struct v4l2_ctrl_ref to the v4l2_ctrl_ref of the
control in such a previous request. So far, so good. However, when that
previous request was applied to the hardware, returned to userspace, and
then userspace would re-init or free that request, any 'ref' pointer in
still-queued requests would suddenly point to freed memory.
This was not noticed before since the drivers that use this expected
that each request would always have the controls set, so there was
never any need to find a control in older requests. This requirement
was relaxed, and now this bug surfaced.
It was also made worse by changeset
2fae4d6aab ("media: v4l2-ctrls: v4l2_ctrl_request_complete() should always set ref->req")
which increased the chance of this happening.
The use of the 'req' pointer in v4l2_ctrl_ref was very fragile, so
drop this entirely. Instead add a valid_p_req bool to indicate that
p_req contains a valid value for this control. And if it is false,
then just use the current value of the control.
Note that VIDIOC_G_EXT_CTRLS will always return -EACCES when attempting
to get a control from a request until the request is completed. And in
that case, all controls in the request will have the control value set
(i.e. valid_p_req is true). This means that the whole 'find the most
recent previous request containing a control' idea is pointless, and
the code can be simplified considerably.
The v4l2_g_ext_ctrls_common() function was refactored a bit to make
it more understandable. It also avoids updating volatile controls
in a completed request since that was already done when the request
was completed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 2fae4d6aab ("media: v4l2-ctrls: v4l2_ctrl_request_complete() should always set ref->req")
Fixes: 6fa6f831f0 ("media: v4l2-ctrls: add core request support")
Cc: <stable@vger.kernel.org> # for v5.9 and up
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add keymaps and bindings for the simple IR (NEC) remotes used with
the MeCool KII-Pro and MeCool KIII-Pro Android STB devices.
Tested-by: Drazen Spio <drazsp@gmail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename v4l2_async_register_subdev_sensor_common as
v4l2_async_register_subdev_sensor. This is a part of the effort to make
the long names present in V4L2 fwnode and async frameworks shorter.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
