During the aborting of a command, the software receives a command
completion event for the command ring stopped, with the TRB pointing
to the next TRB after the aborted command.
If the command we abort is located just before the Link TRB in the
command ring, then during the 'command ring stopped' completion event,
the xHC gives the Link TRB in the event's cmd DMA, which causes a
mismatch in handling command completion event.
To address this situation, move the 'command ring stopped' completion
event check slightly earlier, since the specific command it stopped
on isn't of significant concern.
Fixes: 7f84eef0da ("USB: xhci: No-op command queueing and irq handler.")
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241022155631.1185-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pm_runtime_put in the remove function and pm_runtime_get to disable
RPM on platforms that don't support runtime D3, as re-enabling it through
sysfs auto power control may cause the controller to malfunction. This
can lead to issues such as hotplug devices not being detected due to
failed interrupt generation.
Fixes: a5d6264b63 ("xhci: Enable RPM on controllers that support low-power states")
Cc: stable <stable@kernel.org>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024133718.723846-1-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Treat each completed full size write to /dev/ttyDBC0 as a separate usb
transfer. Make sure the size of the TRBs matches the size of the tty
write by first queuing as many max packet size TRBs as possible up to
the last TRB which will be cut short to match the size of the tty write.
This solves an issue where userspace writes several transfers back to
back via /dev/ttyDBC0 into a kfifo before dbgtty can find available
request to turn that kfifo data into TRBs on the transfer ring.
The boundary between transfer was lost as xhci-dbgtty then turned
everyting in the kfifo into as many 'max packet size' TRBs as possible.
DbC would then send more data to the host than intended for that
transfer, causing host to issue a babble error.
Refuse to write more data to kfifo until previous tty write data is
turned into properly sized TRBs with data size boundaries matching tty
write size
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers fail to produce the final completion event on an
isochronous TD which experienced an error mid TD. We deal with it by
flagging such TDs and checking if the next event points at the flagged
TD or at the next one, and giving back the flagged TD if the latter.
This is not enough, because the next TD may be missed by the xHC. Or
there may be no next TD but a ring underrun. We also need to get such
TD quickly out of the way, or errors on later TDs may be handled wrong.
If the next TD experiences a Missed Service Error, we will set the skip
flag on the endpoint and then attempt skipping TDs when yet another
event arrives. In such scenario, we ought to report the 'error mid TD'
transfer as such rather than skip it.
Another problem case are Stopped events. If we see one after an error
mid TD, we naively assume that it's a Force Stopped Event because it
doesn't match the pending TD, but in reality it might be an ordinary
Stopped event for the next TD, which we fail to recognize and handle.
Fix this by moving error mid TD handling before the whole TD skipping
loop. Remove unnecessary conditions, always give back the TD if the new
event points to any TRB outside it or if the pointer is NULL, as may be
the case in Ring Underrun and Overrun events on 1st gen hardware. Only
if the pending TD isn't flagged, consider other actions like skipping.
As a side effect of reordering with skip and FSE cases, error mid TD is
reordered with last_td_was_short check. This is harmless, because the
two cases are mutually exclusive - only one can happen in any given run
of handle_tx_event().
Tested on the NEC host and a USB camera with flaky cable. Dynamic debug
confirmed that Transaction Errors are sometimes seen, sometimes mid-TD,
sometimes followed by Missed Service. In such cases, they were finished
properly before skipping began.
[Rebase on 6.12-rc1 -Mathias]
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid xHC host from processing a cancelled URB by always turning
cancelled URB TDs into no-op TRBs before queuing a 'Set TR Deq' command.
If the command fails then xHC will start processing the cancelled TD
instead of skipping it once endpoint is restarted, causing issues like
Babble error.
This is not a complete solution as a failed 'Set TR Deq' command does not
guarantee xHC TRB caches are cleared.
Fixes: 4db356924a ("xhci: turn cancelled td cleanup to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stream contex type (SCT) bitfield is used both in the stream context
data structure, and in the 'Set TR Dequeue pointer' command TRB.
In both cases it uses bits 3:1
The SCT_FOR_TRB(p) macro used to set the stream context type (SCT) field
for the 'Set TR Dequeue pointer' command TRB incorrectly shifts the value
1 bit left before masking the three bits.
Fix this by first masking and rshifting, just like the similar
SCT_FOR_CTX(p) macro does
This issue has not been visibile as the lost bit 3 is only used with
secondary stream arrays (SSA). Xhci driver currently only supports using
a primary stream array with Linear stream addressing.
Fixes: 95241dbdf8 ("xhci: Set SCT field for Set TR dequeue on streams")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If USB virtualizatoin is enabled, USB2 ports are shared between all
Virtual Functions. The USB2 port number owned by an USB2 root hub in
a Virtual Function may be less than total USB2 phy number supported
by the Tegra XUSB controller.
Using total USB2 phy number as port number to check all PORTSC values
would cause invalid memory access.
[ 116.923438] Unable to handle kernel paging request at virtual address 006c622f7665642f
...
[ 117.213640] Call trace:
[ 117.216783] tegra_xusb_enter_elpg+0x23c/0x658
[ 117.222021] tegra_xusb_runtime_suspend+0x40/0x68
[ 117.227260] pm_generic_runtime_suspend+0x30/0x50
[ 117.232847] __rpm_callback+0x84/0x3c0
[ 117.237038] rpm_suspend+0x2dc/0x740
[ 117.241229] pm_runtime_work+0xa0/0xb8
[ 117.245769] process_scheduled_works+0x24c/0x478
[ 117.251007] worker_thread+0x23c/0x328
[ 117.255547] kthread+0x104/0x1b0
[ 117.259389] ret_from_fork+0x10/0x20
[ 117.263582] Code: 54000222 f9461ae8 f8747908 b4ffff48 (f9400100)
Cc: stable@vger.kernel.org # v6.3+
Fixes: a30951d31b ("xhci: tegra: USB2 pad power controls")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20241014042134.27664-1-henryl@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZwu6fw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yly6QCfdXwmKEqG4H7xonERzmEkP9/sYtoAnAsafKV5
5pWgy7Jw+WH1s1L7IzGy
=xrG1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
net/9p/usbg: Fix build error
USB: yurex: kill needless initialization in yurex_read
Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
usb: xhci: Fix problem with xhci resume from suspend
usb: misc: onboard_usb_dev: introduce new config symbol for usb5744 SMBus support
usb: dwc3: core: Stop processing of pending events if controller is halted
usb: dwc3: re-enable runtime PM after failed resume
usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
usb: gadget: core: force synchronous registration
I have a ASUS PN51 S mini pc that has two xhci devices. One from AMD,
and other from ASMEDIA. The one from ASMEDIA have problems when resume
from suspend, and keep broken until unplug the power cord. I use this
kernel parameter: xhci-hcd.quirks=128 and then it works ok. I make a
path to reset only the ASMEDIA xhci.
Signed-off-by: Jose Alberto Reguero <jose.alberto.reguero@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240919184202.22249-1-jose.alberto.reguero@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup of
the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART engine
that that chip seems to have. Hopefully it's in a better state now,
but hardware designers still seem to come up with more ways to make
broken UARTS 40+ years after this all should have finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvUz1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAhwCcCw/6BX3aKGTyx7ZxeMRc/mjbSLIAoMUv6bGT
6H04ZvcSd63ZotAWeZsn
=PWB8
-----END PGP SIGNATURE-----
Merge tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
Don't populate the read-only const arrays fifoaddr, fifosel and fifoctr
on the stack at run time, instead make them static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240912132345.589397-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse software managed property 'xhci-skip-phy-init-quirk' and
'xhci-skip-phy-init-quirk' to apply related quirk. It allows usb glue layer
driver apply these quirk.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-1-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow creators of seconday interrupters to specify the interrupt
moderation interval value in nanoseconds when creating the interrupter.
If not sure what value to use then use the xhci driver default
xhci->imod_interval
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI xHC host should be stopped and xhci driver memory freed before putting
host to PCI D3 state during PCI remove callback.
Hosts with XHCI_SPURIOUS_WAKEUP quirk did this the wrong way around
and set the host to D3 before calling usb_hcd_pci_remove(dev), which will
access the host to stop it, and then free xhci.
Fixes: f1f6d9a8b5 ("xhci: don't dereference a xhci member after removing xhci")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce an initial check for an empty list prior to entering the while
loop. Which enables, the implementation of distinct warnings to
differentiate between scenarios where the list is initially empty and
when it has been emptied during processing skipped isoc TDs.
These adjustments not only simplifies the large while loop, but also
facilitates future enhancements to the handle_tx_event() function.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HCD does not allocate or request interrupt for the xhci driver, but HCD
does free and sync xhci interrupts in some cases. Add comment detailing
in which cases HCD will free/sync xhci interrupts.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'sbrn' is used to store the Serial Bus Release Number, which is
then only used for a debug message. Thus, 'sbrn' can be a local variable
and assigned after the primary HCD check. The SBRN debug message is only
printed when a primary HCD is setup.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Completion codes 'COMP_SUCCESS' and 'COMP_SHORT_PACKET' are the most
frequently encountered completion codes. Typically, these codes do not
trigger a default debug message but rather a warning that indicates a
potential issue. This behavior is consistent across all transfer types
with the exception of Bulk transfers. To reduce unnecessary log clutter,
remove the Bulk 'COMP_SHORT_PACKET' debug message.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removed debug messages trigger each time an isoc frame is handled.
In case of an error, a dedicated debug message exists.
For example, a 60fps USB camera will trigger the debug message every 0.6s.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we move the requests from the read_queue to the end of the
read_pool list, avoiding looping and using the same one request all
the time.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't flush all pending DbC data requests when an endpoint halts.
An endpoint may halt and xHC DbC triggers a STALL error event if there's
an issue with a bulk data transfer. The transfer should restart once xHC
DbC receives a ClearFeature(ENDPOINT_HALT) request from the host.
Once xHC DbC restarts it will start from the TRB pointed to by dequeue
field in the endpoint context, which might be the same TRB we got the
STALL event for. Turn the TRB to a no-op in this case to make sure xHC
DbC doesn't reuse and tries to retransmit this same TRB after we already
handled it, and gave its corresponding data request back.
Other STALL events might be completely bogus.
Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events
if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted
endpoints even without any active bulk transfers.
Assume STALL event is spurious if it reports 0 bytes transferred, and
the endpoint stopped on the STALLED TRB.
Don't give back the data request corresponding to the TRB in this case.
The halted status is per endpoint. Track it with a per endpoint flag
instead of the driver invented DbC wide DS_STALLED state.
DbC remains in DbC-Configured state even if endpoints halt. There is no
Stalled state in the DbC Port state Machine (xhci section 7.6.6)
Reported-by: Łukasz Bartosik <ukaszb@chromium.org>
Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'tunnel_mode' enum to usb device structure to describe if a USB3
link is tunneled over USB4, or connected directly using native USB2/USB3
protocols.
Tunneled devices depend on USB4 NHI host to maintain the tunnel.
Knowledge about tunneled devices is important to ensure correct
suspend and resume order between USB4 hosts and tunneled devices.
i.e. make sure tunnel is up before the USB device using it resumes.
USB hosts such as xHCI may have vendor specific ways to detect tunneled
connections. This 'tunnel_mode' parameter can be set by USB3 host driver
during hcd->driver->update_device(hcd, udev) callback.
tunnel_mode can be set to:
USB_LINK_UNKNOWN = 0
USB_LINK_NATIVE
USB_LINK_TUNNELED
USB_LINK_UNKNOWN is used in case host is not capable of detecting
tunneled links.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Knowledge about tunneled devices is useful in order to correctly describe
the relationship between tunneled USB3 device and USB4 Host Interface,
ensuring proper suspend and resume order, and to be able to power down
Thunderbolt if there is no need for tunneling.
Intel hosts share if a USB3 connection is native or tunneled via vendor
specific "SPR eSS PORT" registers.
These vendor registers are available if host supports a vendor specific
SPR shadow extended capability with ID 206. Registers are per USB3 port
and 0x20 apart.
Knowing the tunneling status of the device connected to roothub is enough
as all its children will have the same status.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_get() and clk_prepare_enable() can be replaced by helper
function devm_clk_get_enabled(). Let's use devm_clk_get_enabled() to
simplify code and avoid calling clk_disable_unprepare().
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240902123020.29267-3-zhangzekun11@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240822130113.164644-5-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240821071752.2335406-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240821071856.2335529-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
re-enumerating full-speed devices after a failed address device command
can trigger a NULL pointer dereference.
Full-speed devices may need to reconfigure the endpoint 0 Max Packet Size
value during enumeration. Usb core calls usb_ep0_reinit() in this case,
which ends up calling xhci_configure_endpoint().
On Panther point xHC the xhci_configure_endpoint() function will
additionally check and reserve bandwidth in software. Other hosts do
this in hardware
If xHC address device command fails then a new xhci_virt_device structure
is allocated as part of re-enabling the slot, but the bandwidth table
pointers are not set up properly here.
This triggers the NULL pointer dereference the next time usb_ep0_reinit()
is called and xhci_configure_endpoint() tries to check and reserve
bandwidth
[46710.713538] usb 3-1: new full-speed USB device number 5 using xhci_hcd
[46710.713699] usb 3-1: Device not responding to setup address.
[46710.917684] usb 3-1: Device not responding to setup address.
[46711.125536] usb 3-1: device not accepting address 5, error -71
[46711.125594] BUG: kernel NULL pointer dereference, address: 0000000000000008
[46711.125600] #PF: supervisor read access in kernel mode
[46711.125603] #PF: error_code(0x0000) - not-present page
[46711.125606] PGD 0 P4D 0
[46711.125610] Oops: Oops: 0000 [#1] PREEMPT SMP PTI
[46711.125615] CPU: 1 PID: 25760 Comm: kworker/1:2 Not tainted 6.10.3_2 #1
[46711.125620] Hardware name: Gigabyte Technology Co., Ltd.
[46711.125623] Workqueue: usb_hub_wq hub_event [usbcore]
[46711.125668] RIP: 0010:xhci_reserve_bandwidth (drivers/usb/host/xhci.c
Fix this by making sure bandwidth table pointers are set up correctly
after a failed address device command, and additionally by avoiding
checking for bandwidth in cases like this where no actual endpoints are
added or removed, i.e. only context for default control endpoint 0 is
evaluated.
Reported-by: Karel Balej <balejk@matfyz.cz>
Closes: https://lore.kernel.org/linux-usb/D3CKQQAETH47.1MUO22RTCH2O3@matfyz.cz/
Cc: stable@vger.kernel.org
Fixes: 651aaf36a7 ("usb: xhci: Handle USB transaction error on address command")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240815141117.2702314-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to define one in a custom structure. The tty_port one
is free to use.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20240808103549.429349-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to check against kfifo_len() before kfifo_out(). Just
ask the latter for data and it tells how much it retrieved. Or returns 0
in case there are no more.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20240808103549.429349-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stall handling is managed in the 'process_*' functions, which are called
right before the 'goto' stall handling code snippet. Thus, there should
be a return after the 'process_*' functions. Otherwise, the stall code may
run twice.
Fixes: 1b349f214a ("usb: xhci: add 'goto' for halted endpoint check in handle_tx_event()")
Reported-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240809124408.505786-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xhci_mem_init() fails, it calls into xhci_mem_cleanup() to mop
up the damage. If it fails early enough, before xhci->interrupters
is allocated but after xhci->max_interrupters has been set, which
happens in most (all?) cases, things get uglier, as xhci_mem_cleanup()
unconditionally derefences xhci->interrupters. With prejudice.
Gate the interrupt freeing loop with a check on xhci->interrupters
being non-NULL.
Found while debugging a DMA allocation issue that led the XHCI driver
on this exact path.
Fixes: c99b38c412 ("xhci: add support to allocate several interrupters")
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # 6.8+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240809124408.505786-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_USB_XHCI_PCI_RENESAS is enabled, xhci-pci conditionally
calls into the xhci-pci-renesas module, which means both modules must
be loaded to use any xHCI PCI controller.
The MODULE_FIRMWARE declaration in the base xhci-pci module causes
initramfs-tools to check for and warn about missing firmware for the
Renesas xHCI controllers, when any xHCI PCI controller is present.
And because of the previous oddity, simply moving this declaration to
xhci-pci-renesas wouldn't help.
To fix this, reverse the relationship between the modules:
- Remove the quirk for the Renesas xHCIs, and the driver_data
structure used only for them
- In xhci-pci:
- Rename xhci_pci_probe() to xhci_pci_common_probe()
- Export xhci_pci_common_probe() and xhci_pci_remove()
- Use a new probe function that rejects the Renesas xHCIs and then
calls the common probe function
- In xhci-pci-renesas:
- Stop exporting renesas_xhci_check_request_fw()
- Add a probe function that calls renesas_xhci_check_request_fw()
followed by xhci_pci_common_probe()
- Add and register a new pci_driver matching only the Renesas xHCIs
and using its own probe function, but with other operations the
same as in xhci-pci
- Make CONFIG_USB_XHCI_PCI_RENESAS depend on CONFIG_USB_XHCI_PCI,
not the other way around
Finally, move the MODULE_FIRMWARE declaration to xhci-pci-renesas.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Cyril Brulebois <cyril@debamax.com>
Link: https://lore.kernel.org/r/ZqqfXYRJf7kGaqus@decadent.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ohci-littledian" compatible has typo (edian->endian) and is not
used in in-kernel DTS. Considering the typo and that it is an very old
driver (~2006), drop the compatible.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240712120947.86181-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities for
thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppaNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXZwCgrEtIAQw0x6EF7w/iTWVS5UJj9AEAoLCj5UwO
WX978uThyUctuYYKbw+8
=Cm7j
-----END PGP SIGNATURE-----
Merge tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities
for thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (112 commits)
kselftest: devices: Add test to detect device error logs
kselftest: Move ksft helper module to common directory
kselftest: devices: Move discoverable devices test to subdirectory
usb: gadget: f_uac2: fix non-newline-terminated function name
USB: uas: Implement the new shutdown callback
USB: core: add 'shutdown' callback to usb_driver
usb: typec: Drop explicit initialization of struct i2c_device_id::driver_data to 0
usb: dwc3: enable CCI support for AMD-xilinx DWC3 controller
usb: dwc2: add support for other Lantiq SoCs
usb: gadget: Use u16 types for 16-bit fields
usb: gadget: midi2: Fix incorrect default MIDI2 protocol setup
usb: dwc3: core: Check all ports when set phy suspend
usb: typec: tcpci: add support to set connector orientation
dt-bindings: usb: Convert fsl-usb to yaml
usb: typec: ucsi: reorder operations in ucsi_run_command()
usb: typec: ucsi: extract common code for command handling
usb: typec: ucsi: inline ucsi_read_message_in
usb: typec: ucsi: rework command execution functions
usb: typec: ucsi: split read operation
usb: typec: ucsi: simplify command sending API
...
Usb device connect may not be detected after runtime resume if
xHC is reset during resume.
In runtime resume cases xhci_resume() will only resume roothubs if there
are pending port events. If the xHC host is reset during runtime resume
due to a Save/Restore Error (SRE) then these pending port events won't be
detected as PORTSC change bits are not immediately set by host after reset.
Unconditionally resume roothubs if xHC is reset during resume to ensure
device connections are detected.
Also return early with error code if starting xHC fails after reset.
Issue was debugged and a similar solution suggested by Remi Pommarel.
Using this instead as it simplifies future refactoring.
Reported-by: Remi Pommarel <repk@triplefau.lt>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218987
Suggested-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240627145523.1453155-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci macros that read and write endpoint ID bitfields of TRBs are mixing
the 1-based Endpoint ID as described in the xHCI specification, and
0-based endpoint index used by driver as an array index.
Sort this out by naming macros that deal with 1 based Endpoint ID fields
to *_EP_ID_*, and 0 based endpoint index values to *_EP_INDEX_*.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TGL systems have the same issue as ADL, where a large boot firmware
delay is seen if USB ports are left in U3 at shutdown. So apply the
XHCI_RESET_TO_DEFAULT quirk to TGL as well.
The issue it fixes is a ~20s boot time delay when booting from S5. It
affects TGL devices, and TGL support was added starting from v5.3.
Cc: stable@vger.kernel.org
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'goto' statement for a halted endpoint, streamlining the error
handling process. In future handle_tx_event() changes this 'goto'
statement will have more uses.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This part is and should only performed once, so it's moved out of the
while loop to improve code readability.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a buggy HW reports some unpredicted event (for example, an overrun event
following a MSE event while the EP ring is actually not empty), the driver
will never find the TD, and it will loop until the TD list is empty.
Before commits [1][2], the spin lock was released when giving back a URB in
the do-while loop. This could cause more TD to be added to TD list, causing
an infinite loop.
Because of commits [1][2] the spin lock is not released any more, thus the
infinite loop prevention is unnecessary and is removed.
[1], commit 0c03d89d0c ("xhci: Giveback urb in finish_td directly")
[2], commit 36dc01657b ("usb: host: xhci: Support running urb giveback in
tasklet context")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function doesn't releases and re-acquires the lock, this was removed
in commit 36dc01657b ("usb: host: xhci: Support running urb giveback in
tasklet context")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
