Export the sleepable kfuncs we have on HID-BPF in tracing bpf programs,
but with the condition of being used in a sleepable context.
This allows to use the bpf_timer when used in a sleepable context
through bpf_timer_set_sleepable_cb() and initiate work from a device event.
Link: https://lore.kernel.org/r/20240315-b4-hid-bpf-new-funcs-v4-7-079c282469d3@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
It can be interesting to inject events from BPF as if the event were
to come from the device.
For example, some multitouch devices do not all the time send a proximity
out event, and we might want to send it for the physical device.
Compared to uhid, we can now inject events on any physical device, not
just uhid virtual ones.
Link: https://lore.kernel.org/r/20240315-b4-hid-bpf-new-funcs-v4-5-079c282469d3@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
We currently only export hid_hw_raw_request() as a BPF kfunc.
However, some devices require an explicit write on the Output Report
instead of the use of the control channel.
So also export hid_hw_output_report to BPF
Link: https://lore.kernel.org/r/20240315-b4-hid-bpf-new-funcs-v4-2-079c282469d3@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Distinguish PS4/PS5 type controllers using .driver_data in
MODULE_DEVICE_TABLE rather than by VID/PID.
This allows adding compatible controllers with different VID/PID.
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some third-party controllers never switch to the full 0x11 report.
They keep sending the short 0x01 report, so let's parse that instead.
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some third-party controllers can't report calibration data for the
gyro/accelerometer.
We can still use the gamepad as-is, so let's do that.
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some third-party controllers can't report firmware/hardware version.
Unlike for the DualSense, the driver does not use these values for
anything in the DualShock 4 case, but merely exposes them via sysfs.
They will simply be 0x0.
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
There was no way to disable blinking once enabled.
Disable it on brightness = 0, as per the Linux LED spec.
The driver reports back the values it sends to the controller, but they
need to be scaled back to milliseconds. Setting the LED blinking via
sysfs works as expected now.
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
You can bind whatever action you want to the mouse's reprogrammable
buttons using Windows application. Allow Linux to receive multimedia keycodes.
Fixes: 3ed224e273 ("HID: logitech-dj: Fix 064d:c52f receiver support")
Signed-off-by: Yaraslau Furman <yaro330@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
In af93a167ed, i2c_hid_parse was changed to continue with reading the
report descriptor before waiting for reset to be acknowledged.
This has lead to two regressions:
1. We fail to handle reset acknowledgment if it happens while reading
the report descriptor. The transfer sets I2C_HID_READ_PENDING, which
causes the IRQ handler to return without doing anything.
This affects both a Wacom touchscreen and a Sensel touchpad.
2. On a Sensel touchpad, reading the report descriptor this quickly
after reset results in all zeroes or partial zeroes.
The issues were observed on the Lenovo Thinkpad Z16 Gen 2.
The change in question was made based on a Microsoft article[0] stating
that Windows 8 *may* read the report descriptor in parallel with
awaiting reset acknowledgment, intended as a slight reset performance
optimization. Perhaps they only do this if reset is not completing
quickly enough for their tastes?
As the code is not currently ready to read registers in parallel with a
pending reset acknowledgment, and as reading quickly breaks the report
descriptor on the Sensel touchpad, revert to waiting for reset
acknowledgment before proceeding to read the report descriptor.
[0]: https://learn.microsoft.com/en-us/windows-hardware/drivers/hid/plug-and-play-support-and-power-management
Fixes: af93a167ed ("HID: i2c-hid: Move i2c_hid_finish_hwreset() to after reading the report-descriptor")
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2271136
Cc: stable@vger.kernel.org
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Link: https://lore.kernel.org/r/20240331182440.14477-1-kl@kl.wtf
[hdegoede@redhat.com Drop no longer necessary abort_reset error exit path]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some vendors reuse the same product ID for different tablets, making it
difficult for userspace to figure out which table is connected.
While matching the device name has been used in the past by userspace to
workaround this limitation, some devices have shown that this is not
always a valid approach [1].
However, if userspace could access the firmware version name, it would
be possible to know which tablet is actually connected by matching it
against a list of known firmware names [2].
This patch exposes the firmware version name in the hid->uniq field.
Link: https://github.com/linuxwacom/libwacom/issues/609 [1]
Link: https://github.com/linuxwacom/libwacom/issues/610 [2]
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Hid-debug's rdesc output for a game controller contained a few question
marks and numeric IDs instead of the expected descriptive names.
This happens because:
1) the mapping data is missing event codes defined in input-event-codes.h
2) HID usages aren't up to date
3) hid_resolv_usage fails to account for the sensor pages' modifiers
Add missing event codes and update HID to HUT 1.5.
Signed-off-by: Thomas Kuehne <thomas.kuehne@gmx.li>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() and scnprintf() will be converted as well if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
CC: Jiri Kosina <jikos@kernel.org>
CC: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: linux-input@vger.kernel.org
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() and scnprintf() will be converted as well if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
CC: Stefan Achatz <erazor_de@users.sourceforge.net>
CC: Jiri Kosina <jikos@kernel.org>
CC: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: linux-input@vger.kernel.org
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() and scnprintf() will be converted as well if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
CC: Jiri Kosina <jikos@kernel.org>
CC: Jonathan Cameron <jic23@kernel.org>
CC: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
CC: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: linux-input@vger.kernel.org
CC: linux-iio@vger.kernel.org
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() and scnprintf() will be converted as well if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
CC: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
CC: "Bruno Prémont" <bonbons@linux-vserver.org>
CC: Jiri Kosina <jikos@kernel.org>
CC: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: linux-input@vger.kernel.org
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some third-party controllers can't change the baud rate.
We can still use the gamepad as-is, so let's do that.
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
WinWing Orion2 throttle works with Linux out of box,
but the kernel sees only 16 of 47 buttons on the throttle base.
This module enables all buttons, and also adds LED controls.
Button numbers 0 .. 63 on Orion2 are reserved for throttle grip;
the throttle base buttons have numbers 64 .. 110.
Linux kernel HID subsystem only supports up to 80 buttons.
Remap throttle base buttons to numbers 32 .. 78,
reserving only numbers 0 .. 31 for buttons on the grip handle.
Changes since v2:
- Fixed automatic line wraps added by mail client
Changes since v1:
- Fixed formatting of descriptor byte array;
- Using product codes of Winwing grips in config.
Signed-off-by: Ivan Gorinov <ivan.gorinov@jobyaviation.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Previously, the leds pattern would just increment with every controller
connected. This wouldn't take into consideration when controllers are
disconnected. The same controller could be connected and disconnected
with the pattern increasing player count each time.
This patch changes it by using an ID allocator in order to assign the
player id, the same way hid-playstation does.
Signed-off-by: Martino Fontana <tinozzo123@gmail.com>
Signed-off-by: Ryan McClelland <rymcclel@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Use PCI_VDEVICE() to simplify the device table, and rename these IDs to
follow the pattern PCI_DEVICE_ID_INTEL_*;
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Zhang, Lixu <lixu.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This patch is regarding the recent addition of support for the NSO
controllers to hid-nintendo. All controllers are working correctly with the
exception of the N64 controller, which is being identified as a mouse by
udev. This results in the joystick controlling the mouse cursor and the
controller not being detected by games.
The reason for this is because the N64's C buttons have been attributed to
BTN_FORWARD, BTN_BACK, BTN_LEFT, BTN_RIGHT, which are buttons typically
attributed to mice.
This patch changes those buttons to controller buttons, making the
controller be correctly identified as such.
Signed-off-by: Nuno Pereira <nf.pereira@outlook.pt>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Update the driver to initialize struct fb_info.bl_dev to its backlight
device, if any. Thus rely on the backlight core code to match backlight
and framebuffer devices, and remove the extra check_fb function from
struct backlight_ops.
v2:
* protect against CONFIG_FB_BACKLIGHT (Javier, kernel test robot)
* reword commit message (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20240305162425.23845-5-tzimmermann@suse.de
Signed-off-by: Lee Jones <lee@kernel.org>
For drivers that support backlight, LCD and fbdev devices, fbdev has
to be initialized last. See documentation for struct fbinfo.bl_dev.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20240305162425.23845-4-tzimmermann@suse.de
Signed-off-by: Lee Jones <lee@kernel.org>
The variable dev->devc in ish_dev_init was utilized by dev_err before it
was properly assigned. To rectify this, the assignment of dev->devc has
been moved to immediately follow memory allocation.
Without this change "(NULL device *)" is printed for device information.
Fixes: 8ae2f2b0a2 ("HID: intel-ish-hid: ipc: Fix potential use-after-free in work function")
Fixes: ae02e5d40d ("HID: intel-ish-hid: ipc layer")
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The flag I2C_HID_READ_PENDING is used to serialize I2C operations.
However, this is not necessary, because I2C core already has its own
locking for that.
More importantly, this flag can cause a lock-up: if the flag is set in
i2c_hid_xfer() and an interrupt happens, the interrupt handler
(i2c_hid_irq) will check this flag and return immediately without doing
anything, then the interrupt handler will be invoked again in an
infinite loop.
Since interrupt handler is an RT task, it takes over the CPU and the
flag-clearing task never gets scheduled, thus we have a lock-up.
Delete this unnecessary flag.
Reported-and-tested-by: Eva Kurchatova <nyandarknessgirl@gmail.com>
Closes: https://lore.kernel.org/r/CA+eeCSPUDpUg76ZO8dszSbAGn+UHjcyv8F1J-CUPVARAzEtW9w@mail.gmail.com
Fixes: 4a200c3b9a ("HID: i2c-hid: introduce HID over i2c specification implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+55b
-----END PGP SIGNATURE-----
Merge tag 'hid-for-linus-2024031301' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- support for the following Bluetooth devices from Samsung: Samsung
wireless {Keyboard, GamePad, Action Mouse, Book Cover, Universal
Keyboard, HOGP Keyboard} (Sandeep C S)
- second version of code for applying proper quirk depending on
firmware version for lenovo/cptkbd (Mikhail Khvainitski)
- lenovo/cptkbd firmware-dependent quirk (Mikhail Khvainitski)
- assorted fixes and optimizations for amd-sfh (Basavaraj Natikar)
- dead code and dead data structures removal (Jiri Slaby, Jiapeng
Chong)
* tag 'hid-for-linus-2024031301' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (25 commits)
HID: amd_sfh: Set the AMD SFH driver to depend on x86
HID: input: avoid polling stylus battery on Chromebook Pompom
HID: amd_sfh: Extend MP2 register access to SFH
HID: amd_sfh: Improve boot time when SFH is available
HID: amd_sfh: Avoid disabling the interrupt
HID: amd_sfh: Update HPD sensor structure elements
HID: amd_sfh: Increase sensor command timeout
HID: intel-ish-hid: ipc: Add Arrow Lake PCI device ID
HID: nintendo: Remove some unused functions
HID: hid-prodikeys: remove struct pk_device
HID: hid-prodikeys: remove unused struct pcmidi_snd members
HID: hid-multitouch: remove unused mt_application::dev_time
HID: hid-lg3ff: remove unused struct lg3ff_device
HID: protect hid_device::bpf by CONFIG_HID_BPF
HID: wacom: remove unused hid_data::pressure
HID: apple: remove unused members from struct apple_sc_backlight
HID: wacom: Clean up use of struct->wacom_wac
HID: samsung: Add Samsung wireless bookcover and universal keyboard support
HID: samsung: Add Samsung wireless action mouse support
HID: samsung: Add Samsung wireless gamepad support
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZeEKVAAKCRDbK58LschI
g7oYAQD5Jlv4fIVTvxvfZrTTZ2tU+OsPa75mc8SDKwpash3YygEA8kvESy8+t6pg
D6QmSf1DIZdFoSp/bV+pfkNWMeR8gwg=
=mTAj
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2024-02-29
We've added 119 non-merge commits during the last 32 day(s) which contain
a total of 150 files changed, 3589 insertions(+), 995 deletions(-).
The main changes are:
1) Extend the BPF verifier to enable static subprog calls in spin lock
critical sections, from Kumar Kartikeya Dwivedi.
2) Fix confusing and incorrect inference of PTR_TO_CTX argument type
in BPF global subprogs, from Andrii Nakryiko.
3) Larger batch of riscv BPF JIT improvements and enabling inlining
of the bpf_kptr_xchg() for RV64, from Pu Lehui.
4) Allow skeleton users to change the values of the fields in struct_ops
maps at runtime, from Kui-Feng Lee.
5) Extend the verifier's capabilities of tracking scalars when they
are spilled to stack, especially when the spill or fill is narrowing,
from Maxim Mikityanskiy & Eduard Zingerman.
6) Various BPF selftest improvements to fix errors under gcc BPF backend,
from Jose E. Marchesi.
7) Avoid module loading failure when the module trying to register
a struct_ops has its BTF section stripped, from Geliang Tang.
8) Annotate all kfuncs in .BTF_ids section which eventually allows
for automatic kfunc prototype generation from bpftool, from Daniel Xu.
9) Several updates to the instruction-set.rst IETF standardization
document, from Dave Thaler.
10) Shrink the size of struct bpf_map resp. bpf_array,
from Alexei Starovoitov.
11) Initial small subset of BPF verifier prepwork for sleepable bpf_timer,
from Benjamin Tissoires.
12) Fix bpftool to be more portable to musl libc by using POSIX's
basename(), from Arnaldo Carvalho de Melo.
13) Add libbpf support to gcc in CORE macro definitions,
from Cupertino Miranda.
14) Remove a duplicate type check in perf_event_bpf_event,
from Florian Lehner.
15) Fix bpf_spin_{un,}lock BPF helpers to actually annotate them
with notrace correctly, from Yonghong Song.
16) Replace the deprecated bpf_lpm_trie_key 0-length array with flexible
array to fix build warnings, from Kees Cook.
17) Fix resolve_btfids cross-compilation to non host-native endianness,
from Viktor Malik.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (119 commits)
selftests/bpf: Test if shadow types work correctly.
bpftool: Add an example for struct_ops map and shadow type.
bpftool: Generated shadow variables for struct_ops maps.
libbpf: Convert st_ops->data to shadow type.
libbpf: Set btf_value_type_id of struct bpf_map for struct_ops.
bpf: Replace bpf_lpm_trie_key 0-length array with flexible array
bpf, arm64: use bpf_prog_pack for memory management
arm64: patching: implement text_poke API
bpf, arm64: support exceptions
arm64: stacktrace: Implement arch_bpf_stack_walk() for the BPF JIT
bpf: add is_async_callback_calling_insn() helper
bpf: introduce in_sleepable() helper
bpf: allow more maps in sleepable bpf programs
selftests/bpf: Test case for lacking CFI stub functions.
bpf: Check cfi_stubs before registering a struct_ops type.
bpf: Clarify batch lookup/lookup_and_delete semantics
bpf, docs: specify which BPF_ABS and BPF_IND fields were zero
bpf, docs: Fix typos in instruction-set.rst
selftests/bpf: update tcp_custom_syncookie to use scalar packet offset
bpf: Shrink size of struct bpf_map/bpf_array.
...
====================
Link: https://lore.kernel.org/r/20240301001625.8800-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Considering that amd_sfh exists only on AMD platforms, set the AMD SFH
driver to depend on x86 to avoid build warnings or errors on other
architectures, as shown below.
drivers/hid/amd-sfh-hid/amd_sfh_pcie.c: In function 'amd_mp2_pci_probe':
drivers/hid/amd-sfh-hid/amd_sfh_pcie.c:413:21: error: 'boot_cpu_data'
undeclared (first use in this function); did you mean 'boot_cpu_hwid'?
413 | if (boot_cpu_data.x86 >= 0x1A)
| ^~~~~~~~~~~~~
| boot_cpu_hwid
Fixes: 6296562f30 ("HID: amd_sfh: Extend MP2 register access to SFH")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/all/20240228145648.41c493ec@canb.auug.org.au/
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Internal touchscreen on Trogdor Pompom (AKA Dynabook Chromebook C1)
supports USI stylus. Unfortunately the HID descriptor for the stylus
interface does not contain "Stylus" physical collection, which makes
the kernel to try and pull battery information, resulting in errors.
Apply HID_BATTERY_QUIRK_AVOID_QUERY to the device.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
AMD SFH load takes longer time in initialization. Hence split and defer
initialization code to improve SFH module load time and boot time of the
system when SFH is available.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
HP ProBook x360 435 G7 using older version of firmware which doesn't
support disabling the interrupt for all commands. Hence avoid disabling
the interrupt for that particular model.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218104
Fixes: b300667b33 ("HID: amd_sfh: Disable the interrupt for all command")
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
HPD sensor data is not populating properly because of wrong order of HPD
sensor structure elements. So update the order of structure elements to
match the HPD sensor data received from the firmware.
Fixes: 24a31ea949 ("HID: amd_sfh: Add initial support for HPD sensor")
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
During the initialization sensors may take some time to respond. Hence,
increase the sensor command timeouts in order to obtain status responses
within a maximum timeout.
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Add device ID of Arrow Lake-S into ishtp support list.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
These functions are defined in the hid-nintendo.c file, but not called
elsewhere, so delete these unused functions.
drivers/hid/hid-nintendo.c:757:20: warning: unused function 'joycon_type_has_left_controls'.
drivers/hid/hid-nintendo.c:763:20: warning: unused function 'joycon_type_has_right_controls'.
Fixes: 94f18bb199 ("HID: nintendo: add support for nso controllers")
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=8060
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
First, quirks was unused in struct pk_device.
And I see no reason for this additional level of indirection. struct
pcmidi_snd is far enough for the driver. Unless I am missing something?
So drop struct pk_device and convert all the users to use struct
pcmidi_snd directly. No need for doubled kmalloc+kfrees now.
Found by https://github.com/jirislaby/clang-struct.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
struct pcmidi_snd contains two unused members: out_substream and
out_active. They were added along the driver in commit 3a370ca1dc
(HID: Prodikeys PC-MIDI HID Driver), but not used.
Drop them.
Found by https://github.com/jirislaby/clang-struct.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
dev_time was moved to struct mt_application in commit f146d1c4d7 (HID:
multitouch: Store per collection multitouch data), but is not used since
then. Remove it.
Found by https://github.com/jirislaby/clang-struct.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
struct lg3ff_device is present in the driver since its addition by
commit 74f292ca8c (HID: add driver for the Logitech Flight System
G940).
But it was never used, remove it.
Found by https://github.com/jirislaby/clang-struct.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Gary Stein <LordCnidarian@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The pressure member in struct hid_data is unused. It was
added in commit 5ae6e89f74 (HID: wacom: implement the finger part of
the HID generic handling), but never used.
As this is not a struct to communicate with the HW, remove that member.
Found by https://github.com/jirislaby/clang-struct.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Ping Cheng <ping.cheng@wacom.com>
Cc: Jason Gerecke <jason.gerecke@wacom.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The backlight members in struct apple_sc_backlight are unused. They were
added in commit 9018eacbe6 (HID: apple: Add support for keyboard
backlight on certain T2 Macs.), but never used.
As this is not a struct to communicate with the HW, remove these.
Found by https://github.com/jirislaby/clang-struct.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Paul Pawlowski <paul@mrarm.io>
Cc: Aun-Ali Zaidi <admin@kodeit.net>
Cc: Aditya Garg <gargaditya08@live.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Replace the indirect accesses to struct->wacom_wac from struct->wacom
to the direct access in order for better code reading.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The xf86-input-wacom driver does not treat '0' as a valid serial
number and will drop any input report which contains an
MSC_SERIAL = 0 event. The kernel driver already takes care to
avoid sending any MSC_SERIAL event if the value of serial[0] == 0
(which is the case for devices that don't actually report a
serial number), but this is not quite sufficient.
Only the lower 32 bits of the serial get reported to userspace,
so if this portion of the serial is zero then there can still
be problems.
This commit allows the driver to report either the lower 32 bits
if they are non-zero or the upper 32 bits otherwise.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
CC: stable@vger.kernel.org # v4.10
Signed-off-by: Jiri Kosina <jkosina@suse.com>
After legacy suspend/resume via ACPI S3, sensor read operation fails
with timeout. Also, it will cause delay in resume operation as there
will be retries on failure.
This is caused by commit f645a90e8f ("HID: intel-ish-hid:
ishtp-hid-client: use helper functions for connection"), which used
helper functions to simplify connect, reset and disconnect process.
Also avoid freeing and allocating client buffers again during reconnect
process.
But there is a case, when ISH firmware resets after ACPI S3 suspend,
ishtp bus driver frees client buffers. Since there is no realloc again
during reconnect, there are no client buffers available to send connection
requests to the firmware. Without successful connection to the firmware,
subsequent sensor reads will timeout.
To address this issue, ishtp bus driver does not free client buffers on
warm reset after S3 resume. Simply add the buffers from the read list
to free list of buffers.
Fixes: f645a90e8f ("HID: intel-ish-hid: ishtp-hid-client: use helper functions for connection")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218442
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Add support for the pointing stick (Accupoint) and 2 mouse buttons.
Present on some Toshiba/dynabook Portege X30 and X40 laptops.
It should close https://bugzilla.kernel.org/show_bug.cgi?id=205817
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
If a input device is opened before hid_hw_start is called, events may
not be received from the hardware. In the case of USB-backed devices,
for example, the hid_hw_start function is responsible for filling in
the URB which is submitted when the input device is opened. If a device
is opened prematurely, polling will never start because the device will
not have been in the correct state to send the URB.
Because the wacom driver registers its input devices before calling
hid_hw_start, there is a window of time where a device can be opened
and end up in an inoperable state. Some ARM-based Chromebooks in particular
reliably trigger this bug.
This commit splits the wacom_register_inputs function into two pieces.
One which is responsible for setting up the allocated inputs (and runs
prior to hid_hw_start so that devices are ready for any input events
they may end up receiving) and another which only registers the devices
(and runs after hid_hw_start to ensure devices can be immediately opened
without issue). Note that the functions to initialize the LEDs and remotes
are also moved after hid_hw_start to maintain their own dependency chains.
Fixes: 7704ac9373 ("HID: wacom: implement generic HID handling for pen generic devices")
Cc: stable@vger.kernel.org # v3.18+
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Since commit 680ee411a9 ("HID: logitech-hidpp: Fix connect event race")
the following messages appear in the kernel log from time to time:
logitech-hidpp-device 0003:046D:408A.0005: HID++ 4.5 device connected.
logitech-hidpp-device 0003:046D:408A.0005: HID++ 4.5 device connected.
logitech-hidpp-device 0003:046D:4051.0006: Disconnected
logitech-hidpp-device 0003:046D:408A.0005: Disconnected
As discussed, print the first per-device "device connected" message
at info level, demoting subsequent messages to debug level. Also,
demote the "Disconnected message" to debug level unconditionally.
Link: https://lore.kernel.org/lkml/3277085.44csPzL39Z@natalenko.name/
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This commit marks kfuncs as such inside the .BTF_ids section. The upshot
of these annotations is that we'll be able to automatically generate
kfunc prototypes for downstream users. The process is as follows:
1. In source, use BTF_KFUNCS_START/END macro pair to mark kfuncs
2. During build, pahole injects into BTF a "bpf_kfunc" BTF_DECL_TAG for
each function inside BTF_KFUNCS sets
3. At runtime, vmlinux or module BTF is made available in sysfs
4. At runtime, bpftool (or similar) can look at provided BTF and
generate appropriate prototypes for functions with "bpf_kfunc" tag
To ensure future kfunc are similarly tagged, we now also return error
inside kfunc registration for untagged kfuncs. For vmlinux kfuncs,
we also WARN(), as initcall machinery does not handle errors.
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/e55150ceecbf0a5d961e608941165c0bee7bc943.1706491398.git.dxu@dxuuu.xyz
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Follow the docs at Documentation/bpf/kfuncs.rst:
- declare the function with `__bpf_kfunc`
- disables missing prototype warnings, which allows to remove them from
include/linux/hid-bpf.h
Removing the prototypes is not an issue because we currently have to
redeclare them when writing the BPF program. They will eventually be
generated by bpftool directly AFAIU.
Link: https://lore.kernel.org/r/20240124-b4-hid-bpf-fixes-v2-3-052520b1e5e6@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Turns out that I got my reference counts wrong and each successful
bus_find_device() actually calls get_device(), and we need to manually
call put_device().
Ensure each bus_find_device() gets a matching put_device() when releasing
the bpf programs and fix all the error paths.
Cc: <stable@vger.kernel.org>
Fixes: f5c27da4e3 ("HID: initial BPF implementation")
Link: https://lore.kernel.org/r/20240124-b4-hid-bpf-fixes-v2-2-052520b1e5e6@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
When the kfunc hid_bpf_attach_prog() is called, we called twice fdget():
one for fetching the type of the bpf program, and one for actually
attaching the program to the device.
The problem is that between those two calls, we have no guarantees that
the prog_fd is still the same file descriptor for the given program.
Solve this by calling bpf_prog_get() earlier, and use this to fetch the
program type.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/bpf/CAO-hwJJ8vh8JD3-P43L-_CLNmPx0hWj44aom0O838vfP4=_1CA@mail.gmail.com/T/#t
Cc: <stable@vger.kernel.org>
Fixes: f5c27da4e3 ("HID: initial BPF implementation")
Link: https://lore.kernel.org/r/20240124-b4-hid-bpf-fixes-v2-1-052520b1e5e6@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
A while back the I2C HID implementation was split in an ACPI and OF
part, but the new OF driver never initialises the client pointer which
is dereferenced on power-up failures.
Fixes: b33752c300 ("HID: i2c-hid: Reorganize so ACPI and OF are separate modules")
Cc: stable@vger.kernel.org # 5.12
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Resolved warnings found by checkpatch.pl script.
Signed-off-by: Sandeep C S <sandeep.cs@samsung.com>
Signed-off-by: Junwan Cho <junwan.cho@samsung.com>
Signed-off-by: Jitender Sajwan <jitender.s21@samsung.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The USB validation check has been moved wherever its required.
Earlier Samsung driver only handles USB HID devices and returns an error if it
encounters a Bluetooth type of HID device. This changes improves driver
compatibility and extends its support for a wide range of devices.
Signed-off-by: Sandeep C S <sandeep.cs@samsung.com>
Signed-off-by: Junwan Cho <junwan.cho@samsung.com>
Signed-off-by: Jitender Sajwan <jitender.s21@samsung.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
'struct hidraw_list' is a circular queue whose head can be smaller than
tail. Using 'list->tail != list->head' to release all memory that should
be released.
Fixes: a5623a203c ("HID: hidraw: fix memory leak in hidraw_release()")
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Previous attempt to autodetect well-behaving patched firmware
introduced in commit 46a0a2c96f ("HID: lenovo: Detect quirk-free fw
on cptkbd and stop applying workaround") has shown that there are
false-positives on original firmware (on both 1st gen and 2nd gen
keyboards) which causes the middle button click workaround to be
mistakenly disabled.
This commit adds explicit parameter to sysfs to control this
workaround.
Fixes: 46a0a2c96f ("HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround")
Fixes: 43527a0094 ("HID: lenovo: Restrict detection of patched firmware only to USB cptkbd")
Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
There's a Cirque touchpad that wakes system up without anything touched
the touchpad. The input report is empty when this happens.
The reason is stated in HID over I2C spec, 7.2.8.2:
"If the DEVICE wishes to wake the HOST from its low power state, it can
issue a wake by asserting the interrupt."
This is fine if OS can put system back to suspend by identifying input
wakeup count stays the same on resume, like Chrome OS Dark Resume [0].
But for regular distro such policy is lacking.
Though the change doesn't bring any impact on power consumption for
touchpad is minimal, other i2c-hid device may depends on SLEEP control
power. So use a quirk to limit the change scope.
[0] https://chromium.googlesource.com/chromiumos/platform2/+/HEAD/power_manager/docs/dark_resume.md
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.
[jkosina@suse.com: tweak changelog a bit]
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
These functions are defined in the hid-nintendo.c file, but not called
elsewhere, so delete these unused functions.
drivers/hid/hid-nintendo.c:670:20: warning: unused function 'joycon_device_is_left_joycon'.
drivers/hid/hid-nintendo.c:674:20: warning: unused function 'joycon_device_is_right_joycon'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7992
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Let logitech-hidpp driver claim Logitech G Pro X Superlight 2.
Reported-by: Marcus Rückert <darix@opensu.se>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
There are a number of issues in this code. First of all if
steam_create_client_hid() fails then it leads to an error pointer
dereference when we call hid_destroy_device(steam->client_hdev).
Also there are a number of leaks. hid_hw_stop() is not called if
hid_hw_open() fails for example. And it doesn't call steam_unregister()
or hid_hw_close().
Fixes: 691ead124a ("HID: hid-steam: Clean up locking")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vicki Pfau <vi@endrift.com>
Link: https://lore.kernel.org/r/1fd87904-dabf-4879-bb89-72d13ebfc91e@moroto.mountain
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
This error message doesn't really add any information. If modprobe
fails then the user will already know what the error code is. In the
case of kmalloc() it's a style violation to print an error message for
that because kmalloc has it's own better error messages built in.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vicki Pfau <vi@endrift.com>
Link: https://lore.kernel.org/r/305898fb-6bd4-4749-806c-05ec51bbeb80@moroto.mountain
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3SCb
-----END PGP SIGNATURE-----
Merge tag 'hid-for-linus-2024010801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- assorted functional fixes for hid-steam ported from SteamOS betas
(Vicki Pfau)
- fix for custom sensor-hub sensors (hinge angle sensor and LISS
sensors) not working (Yauhen Kharuzhy)
- functional fix for handling Confidence in Wacom driver (Jason
Gerecke)
- support for Ilitek ili2901 touchscreen (Zhengqiao Xia)
- power management fix for Wacom userspace battery exporting
(Tatsunosuke Tobita)
- rework of wait-for-reset in order to reduce the need for
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET qurk; the success rate is now 50%
better, but there are still further improvements to be made (Hans de
Goede)
- greatly improved coverage of Tablets in hid-selftests (Benjamin
Tissoires)
- support for Nintendo NSO controllers -- SNES, Genesis and N64 (Ryan
McClelland)
- support for controlling mcp2200 GPIOs (Johannes Roith)
- power management improvement for EHL OOB wakeup in intel-ish
(Kai-Heng Feng)
- other assorted device-specific fixes and code cleanups
* tag 'hid-for-linus-2024010801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (53 commits)
HID: amd_sfh: Add a new interface for exporting ALS data
HID: amd_sfh: Add a new interface for exporting HPD data
HID: amd_sfh: rename float_to_int() to amd_sfh_float_to_int()
HID: i2c-hid: elan: Add ili2901 timing
dt-bindings: HID: i2c-hid: elan: Introduce Ilitek ili2901
HID: bpf: make bus_type const in struct hid_bpf_ops
HID: make ishtp_cl_bus_type const
HID: make hid_bus_type const
HID: hid-steam: Add gamepad-only mode switched to by holding options
HID: hid-steam: Better handling of serial number length
HID: hid-steam: Update list of identifiers from SDL
HID: hid-steam: Make client_opened a counter
HID: hid-steam: Clean up locking
HID: hid-steam: Disable watchdog instead of using a heartbeat
HID: hid-steam: Avoid overwriting smoothing parameter
HID: magicmouse: fix kerneldoc for struct magicmouse_sc
HID: sensor-hub: Enable hid core report processing for all devices
HID: wacom: Add additional tests of confidence behavior
HID: wacom: Correct behavior when processing some confidence == false touches
HID: nintendo: add support for nso controllers
...
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name
-----BEGIN PGP SIGNATURE-----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=nuw0
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This contains two major new drivers:
- imagination is a first driver for Imagination Technologies devices,
it only covers very specific devices, but there is hope to grow it
- xe is a reboot of the i915 GPU (shares display) side using a more
upstream focused development model, and trying to maximise code
sharing. It's not enabled for any hw by default, and will hopefully
get switched on for Intel's Lunarlake.
This also drops a bunch of the old UMS ioctls. It's been dead long
enough.
amdgpu has a bunch of new color management code that is being used in
the Steam Deck.
amdgpu also has a new ACPI WBRF interaction to help avoid radio
interference.
Otherwise it's the usual lots of changes in lots of places.
Detailed summary:
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name"
* tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits)
drm/amd/display: Allow z8/z10 from driver
drm/amd/display: fix bandwidth validation failure on DCN 2.1
drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well
drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm
drm/amd/display: Fix recent checkpatch errors in amdgpu_dm
Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"
drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()
drm/amd/display: Fix power_helpers.c codestyle
drm/amd/display: Fix hdcp_log.h codestyle
drm/amd/display: Fix hdcp2_execution.c codestyle
drm/amd/display: Fix hdcp_psp.h codestyle
drm/amd/display: Fix freesync.c codestyle
drm/amd/display: Fix hdcp_psp.c codestyle
drm/amd/display: Fix hdcp1_execution.c codestyle
drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()'
drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c
drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()'
drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()'
...
- Introduce the param_unknown_fn type and other clean ups (Andy Shevchenko)
- Various __counted_by annotations (Christophe JAILLET, Gustavo A. R. Silva,
Kees Cook)
- Add KFENCE test to LKDTM (Stephen Boyd)
- Various strncpy() refactorings (Justin Stitt)
- Fix qnx4 to avoid writing into the smaller of two overlapping buffers
- Various strlcpy() refactorings
-----BEGIN PGP SIGNATURE-----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=1Wxx
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
- Introduce the param_unknown_fn type and other clean ups (Andy
Shevchenko)
- Various __counted_by annotations (Christophe JAILLET, Gustavo A. R.
Silva, Kees Cook)
- Add KFENCE test to LKDTM (Stephen Boyd)
- Various strncpy() refactorings (Justin Stitt)
- Fix qnx4 to avoid writing into the smaller of two overlapping buffers
- Various strlcpy() refactorings
* tag 'hardening-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
qnx4: Use get_directory_fname() in qnx4_match()
qnx4: Extract dir entry filename processing into helper
atags_proc: Add __counted_by for struct buffer and use struct_size()
tracing/uprobe: Replace strlcpy() with strscpy()
params: Fix multi-line comment style
params: Sort headers
params: Use size_add() for kmalloc()
params: Do not go over the limit when getting the string length
params: Introduce the param_unknown_fn type
lkdtm: Add kfence read after free crash type
nvme-fc: replace deprecated strncpy with strscpy
nvdimm/btt: replace deprecated strncpy with strscpy
nvme-fabrics: replace deprecated strncpy with strscpy
drm/modes: replace deprecated strncpy with strscpy_pad
afs: Add __counted_by for struct afs_acl and use struct_size()
VMCI: Annotate struct vmci_handle_arr with __counted_by
i40e: Annotate struct i40e_qvlist_info with __counted_by
HID: uhid: replace deprecated strncpy with strscpy
samples: Replace strlcpy() with strscpy()
SUNRPC: Replace strlcpy() with strscpy()
- rework of wait-for-reset in order to reduce the need
for I2C_HID_QUIRK_NO_IRQ_AFTER_RESET qurk; the success rate is now
50% better, but there are still further improvements to be made (Hans de Goede)
AMDSFH has information about the Ambient light via the Ambient
Light Sensor (ALS) which is part of the AMD sensor fusion hub.
Add a new interface to export this information, where other drivers like
PMF can use this information to enhance user experiences.
Link: https://lore.kernel.org/all/ad064333-48a4-4cfa-9428-69e8a7c44667@redhat.com/
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
AMDSFH has information about the User presence information via the Human
Presence Detection (HPD) sensor which is part of the AMD sensor fusion hub.
Add a new interface to export this information, where other drivers like
PMF can use this information to enhance user experiences.
Link: https://lore.kernel.org/all/ad064333-48a4-4cfa-9428-69e8a7c44667@redhat.com/
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Current amd_sfh driver has float_to_int() to convert units from
float to int. This is fine until this function gets called outside of
the current scope of file.
Add a prefix "amd_sfh" to float_to_int() so that function represents
the driver name. This function will be called by multiple callers in the
next patch.
Link: https://lore.kernel.org/all/ad064333-48a4-4cfa-9428-69e8a7c44667@redhat.com/
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
ILI2901 requires reset to pull down time greater than 10ms,
so the configuration post_power_delay_ms is 10, and the chipset
initial time is required to be greater than 100ms,
so the post_gpio_reset_on_delay_ms is set to 100.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Zhengqiao Xia <xiazhengqiao@huaqin.corp-partner.google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Now that the driver core can properly handle constant struct bus_type,
move the ishtp_cl_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Now that the driver core can properly handle constant struct bus_type,
move the hid_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This commit adds a hotkey to switch between "gamepad" mode (mouse and keyboard
disabled) and "desktop" mode (gamepad disabled) by holding down the options
button (mapped here as the start button). This mirrors the behavior of the
official Steam client.
This also adds and uses a function for generating haptic pulses, as Steam also
does when engaging this hotkey.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The second byte of the GET_STRING_ATTRIB report is a length, so we should set
the size of the buffer to be the size we're actually requesting, and only
reject the reply if the length out is nonsensical.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
SDL includes a list of settings (formerly called registers in this driver),
reports (formerly cmds), and various other identifiers that were provided by
Valve. This commit imports a significant chunk of that list as well as
replacing most of the guessed names and a handful of magic constants. It also
replaces bitmask definitions that used hex with the BIT macro.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The client_opened variable was used to track if the hidraw was opened by any
clients to silence keyboard/mouse events while opened. However, there was no
counting of how many clients were opened, so opening two at the same time and
then closing one would fool the driver into thinking it had no remaining opened
clients.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This cleans up the locking logic so that the spinlock is consistently used for
access to a small handful of struct variables, and the mutex is exclusively and
consistently used for ensuring that mutliple threads aren't trying to
send/receive reports at the same time. Previously, only some report
transactions were guarded by this mutex, potentially breaking atomicity. The
mutex has been renamed to reflect this usage.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The Steam Deck has a setting that controls whether or not the watchdog is
enabled, so instead of using a heartbeat to keep the watchdog from triggering,
this commit changes the behavior to simply disable the watchdog instead.
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The original implementation of this driver incorrectly guessed the function of
this register. It's not only unnecessary to write to this register for lizard
mode but actually counter-productive since it overwrites whatever previous
value was intentionally set, for example by Steam.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
After the commit 666cf30a58 ("HID: sensor-hub: Allow multi-function
sensor devices") hub devices are claimed by hidraw driver in hid_connect().
This causes stoppping of processing HID reports by hid core due to
optimization.
In such case, the hid-sensor-custom driver cannot match a known custom
sensor in hid_sensor_custom_get_known() because it try to check custom
properties which weren't filled from the report because hid core didn't
parsed it.
As result, custom sensors like hinge angle sensor and LISS sensors
don't work.
Mark the sensor hub devices claimed by some driver to avoid hidraw-related
optimizations.
Fixes: 666cf30a58 ("HID: sensor-hub: Allow multi-function sensor devices")
Cc: stable@vger.kernel.org
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20231219231503.1506801-1-jekhor@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
There appear to be a few different ways that Wacom devices can deal with
confidence:
1. If the device looses confidence in a touch, it will first clear
the tipswitch flag in one report, and then clear the confidence
flag in a second report. This behavior is used by e.g. DTH-2452.
2. If the device looses confidence in a touch, it will clear both
the tipswitch and confidence flags within the same report. This
behavior is used by some AES devices.
3. If the device looses confidence in a touch, it will clear *only*
the confidence bit. The tipswitch bit will remain set so long as
the touch is tracked. This behavior may be used in future devices.
The driver does not currently handle situation 3 properly. Touches that
loose confidence will remain "in prox" and essentially frozen in place
until the tipswitch bit is finally cleared. Not only does this result
in userspace seeing a stuck touch, but it also prevents pen arbitration
from working properly (the pen won't send events until all touches are
up, but we don't currently process events from non-confident touches).
This commit centralizes the checking of the confidence bit in the
wacom_wac_finger_slot() function and has 'prox' depend on it. In the
case where situation 3 is encountered, the treat the touch as though
it was removed, allowing both userspace and the pen arbitration to
act normally.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 7fb0413baa ("HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Z8bG
-----END PGP SIGNATURE-----
Merge tag 'hid-for-linus-2023121901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- fix for division by zero in Nintendo driver when generic joycon is
attached, reported and fixed by SteamOS folks (Guilherme G. Piccoli)
- GCC-7 build fix (which is a good cleanup anyway) for Nintendo driver
(Ryan McClelland)
* tag 'hid-for-linus-2023121901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: nintendo: Prevent divide-by-zero on code
HID: nintendo: fix initializer element is not constant error
It was reported [0] that adding a generic joycon to the system caused
a kernel crash on Steam Deck, with the below panic spew:
divide error: 0000 [#1] PREEMPT SMP NOPTI
[...]
Hardware name: Valve Jupiter/Jupiter, BIOS F7A0119 10/24/2023
RIP: 0010:nintendo_hid_event+0x340/0xcc1 [hid_nintendo]
[...]
Call Trace:
[...]
? exc_divide_error+0x38/0x50
? nintendo_hid_event+0x340/0xcc1 [hid_nintendo]
? asm_exc_divide_error+0x1a/0x20
? nintendo_hid_event+0x307/0xcc1 [hid_nintendo]
hid_input_report+0x143/0x160
hidp_session_run+0x1ce/0x700 [hidp]
Since it's a divide-by-0 error, by tracking the code for potential
denominator issues, we've spotted 2 places in which this could happen;
so let's guard against the possibility and log in the kernel if the
condition happens. This is specially useful since some data that
fills some denominators are read from the joycon HW in some cases,
increasing the potential for flaws.
[0] https://github.com/ValveSoftware/SteamOS/issues/1070
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Tested-by: Sam Lantinga <slouken@libsdl.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
With gcc-7 builds, an error happens with the controller button values being
defined as const. Change to a define.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312141227.C2h1IzfI-lkp@intel.com/
Signed-off-by: Ryan McClelland <rymcclel@gmail.com>
Reviewed-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This adds support for the nintendo switch online controllers which
include the SNES, Genesis, and N64 Controllers.
As each nso controller only implements a subset of what a pro
controller can do. Each of these 'features' were broken up in to
seperate functions which include right stick, left stick, imu, and
dpad and depending on the controller type that it is, it will call
the supported functions appropriately.
Each controller now has a struct which maps the bit within the hid
in report to a button.
The name given to the device now comes directly from the hid
device name rather than looking up a predefined string.
Signed-off-by: Ryan McClelland <rymcclel@gmail.com>
Reviewed-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Tested-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
JingZao(京造) WKB603 keyboard is a rebranded product of Jamesdonkey RS2
keyboard, identified as "hfd.cn WKB603" in wired mode, "WKB603" in bluetooth
mode. Adding them to the list of non-apple keyboards fixes function key.
Signed-off-by: Yan Jun <jerrysteve1101@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Commit 46a0a2c96f ("HID: lenovo: Detect quirk-free fw on cptkbd and
stop applying workaround") introduced a regression for ThinkPad
TrackPoint Keyboard II which has similar quirks to cptkbd (so it uses
the same workarounds) but slightly different so that there are
false-positives during detecting well-behaving firmware. This commit
restricts detecting well-behaving firmware to the only model which
known to have one and have stable enough quirks to not cause
false-positives.
Fixes: 46a0a2c96f ("HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround")
Link: https://lore.kernel.org/linux-input/ZXRiiPsBKNasioqH@jekhomev/
Link: https://bbs.archlinux.org/viewtopic.php?pid=2135468#p2135468
Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Since PCI core and ACPI core already handles PCI PME wake and GPE wake
when the device has wakeup capability, use device_init_wakeup() to let
them do the wakeup setting work.
Also add a shutdown callback which uses pci_prepare_to_sleep() to let
PCI and ACPI set OOB wakeup for S5.
Cc: Jian Hui Lee <jianhui.lee@canonical.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The quirks variable and the I2C_HID_QUIRK_ defines are never used /
exported outside of the i2c-hid code renumber them to start at
BIT(0) again.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Re-trying the power-on command on failure on all devices should
not be a problem, drop the I2C_HID_QUIRK_SET_PWR_WAKEUP_DEV quirk
and simply retry power-on on all devices.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
On all i2c-hid devices seen sofar the reset-ack either works, or the hw is
somehow buggy and does not (always) ack the reset properly, yet it still
works fine.
Lower the very long reset timeout to 1 second which should be plenty
and change the reset not getting acked from an error into a warning.
This results in a bit cleaner code and avoids the need to add more
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET quirks in the future.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
A recent bug made me look at Microsoft's i2c-hid docs again
and I noticed the following:
"""
4. Issue a RESET (Host Initiated Reset) to the Device.
5. Retrieve report descriptor from the device.
Note: Steps 4 and 5 may be done in parallel to optimize for time on I²C.
Since report descriptors are (a) static and (b) quite long, Windows 8 may
issue a request for 5 while it is waiting for a response from the device
on 4.
"""
Which made me think that maybe on some touchpads the reset ack is delayed
till after the report descriptor is read ?
Testing a T-BAO Tbook Air 12.5 with a 0911:5288 (SIPODEV SP1064?) touchpad,
for which the I2C_HID_QUIRK_NO_IRQ_AFTER_RESET quirk was first introduced,
shows that reading the report descriptor before waiting for the reset
helps with the missing reset IRQ. Now the reset does get acked properly,
but the ack sometimes still does not happen unfortunately.
Still moving the wait for ack to after reading the report-descriptor,
is probably a good idea, both to make i2c-hid's behavior closer to
Windows as well as to speed up probing i2c-hid devices.
While at it drop the dbg_hid() for a malloc failure, malloc failures
already get logged extensively by malloc itself.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2247751
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Switch i2c_hid_parse() to goto style error handling.
This is a preparation patch for removing the need for
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET by making i2c-hid behave
more like Windows.
Note this changes the descriptor read error path to propagate
the actual i2c_hid_read_register() error code (which is always
negative) instead of hardcoding a -EIO return.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Split i2c_hid_hwreset() into:
i2c_hid_start_hwreset() which sends the PWR_ON and reset commands; and
i2c_hid_finish_hwreset() which actually waits for the reset to complete.
This is a preparation patch for removing the need for
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET by making i2c-hid behave
more like Windows.
No functional changes intended.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
i2c_hid_hwreset() is the only caller of i2c_hid_execute_reset(),
fold the latter into the former.
This is a preparation patch for removing the need for
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET by making i2c-hid behave
more like Windows.
No functional changes intended.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Use helper functions ishtp_cl_establish_connection() and
ishtp_cl_destroy_connection() to establish and destroy connection
respectively. These functions are used during initialization, reset and
deinitialization flows.
No functional changes are expected.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Use helper functions ishtp_cl_establish_connection() and
ishtp_cl_destroy_connection() to establish and destroy connection
respectively. These functions are used during initialization, reset and
deinitialization flows.
No functional changes are expected.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
For every ishtp client driver during initialization state, the flow is:
1 - Allocate an ISHTP client instance
2 - Reserve a host id and link the client instance
3 - Search a firmware client using UUID and get related
client information
4 - Bind firmware client id to the ISHTP client instance
5 - Set the state the ISHTP client instance to CONNECTING
6 - Send connect request to firmware
7 - Register event callback for messages from the firmware
During deinitizalization state, the flow is:
9 - Set the state the ISHTP client instance to ISHTP_CL_DISCONNECTING
10 - Issue disconnect request to firmware
11 - Unlike the client instance
12 - Flush message queue
13 - Free ISHTP client instance
Step 2-7 are identical to the steps of client driver initialization
and driver reset flow, but reallocation of the RX/TX ring buffers
can be avoided in reset flow.
Also for step 9-12, they are identical to the steps of client driver
failure handling after connect request, driver reset flow and
driver removing.
So, add two helper functions to simplify client driver code.
ishtp_cl_establish_connection()
ishtp_cl_destroy_connection()
No functional changes are expected.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This device needs ALWAYS_POLL quirk, otherwise it keeps reconnecting
indefinitely. It is a handbrake for sim racing detected as joystick.
Reported and tested by GitHub user N0th1ngM4tt3rs.
Link: https://github.com/sriemer/fix-linux-mouse issue 22
Signed-off-by: Sebastian Parschauer <s.parschauer@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Users have reported problems with recent Lenovo laptops that contain
an IDEA5002 I2C HID device. Reports include fans turning on and
running even at idle and spurious wakeups from suspend.
Presumably in the Windows ecosystem there is an application that
uses the HID device. Maybe that puts it into a lower power state so
it doesn't cause spurious events.
This device doesn't serve any functional purpose in Linux as nothing
interacts with it so blacklist it from being probed. This will
prevent the GPIO driver from setting up the GPIO and the spurious
interrupts and wake events will not occur.
Cc: stable@vger.kernel.org # 6.1
Reported-and-tested-by: Marcus Aram <marcus+oss@oxar.nl>
Reported-and-tested-by: Mark Herbert <mark.herbert42@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2812
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Even if a user does not use their AES pen for an extended period,
the battery power supply attributes continue to exist.
This results in the desktop showing battery status for a pen
that is no longer in use and which may in fact be in a different
state (e.g. the user may be charging the pen).
To avoid confusion and ensure userspace has an accurate view
of the battery state, this patch automatically removes
the power_supply after 30 minutes of inactivity.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Reviewed-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Josh Dickens <joshua.dickens@wacom.com>
Link: https://lore.kernel.org/r/20231114235729.6867-1-tatsunosuke.wacom@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The picolcd_fb driver operates on system memory. Mark the framebuffer
accordingly. Helpers operating on the framebuffer memory will test
for the presence of this flag.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127131655.4020-12-tzimmermann@suse.de
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CmgY
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2023112301' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- revert of commit that caused regression to many Logitech unifying
receiver users (Jiri Kosina)
- power management fix for hid-mcp2221 (Hamish Martin)
- fix for race condition between HID core and HID debug (Charles Yi)
- a couple of assorted device-ID-specific quirks
* tag 'for-linus-2023112301' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: multitouch: Add quirk for HONOR GLO-GXXX touchpad
HID: hid-asus: reset the backlight brightness level on resume
HID: hid-asus: add const to read-only outgoing usb buffer
Revert "HID: logitech-dj: Add support for a new lightspeed receiver iteration"
HID: add ALWAYS_POLL quirk for Apple kb
HID: glorious: fix Glorious Model I HID report
HID: fix HID device resource race between HID core and debugging support
HID: apple: add Jamesdonkey and A3R to non-apple keyboards list
HID: mcp2221: Allow IO to start during probe
HID: mcp2221: Set driver data before I2C adapter add
Honor MagicBook 13 2023 has a touchpad which do not switch to the multitouch
mode until the input mode feature is written by the host. The touchpad do
report the input mode at touchpad(3), while itself working under mouse mode. As
a workaround, it is possible to call MT_QUIRE_FORCE_GET_FEATURE to force set
feature in mt_set_input_mode for such device.
The touchpad reports as BLTP7853, which cannot retrive any useful manufacture
information on the internel by this string at present. As the serial number of
the laptop is GLO-G52, while DMI info reports the laptop serial number as
GLO-GXXX, this workaround should applied to all models which has the GLO-GXXX.
Signed-off-by: Aoba K <nexp_0x17@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some devices managed by this driver automatically set brightness to 0
before entering a suspended state and reset it back to a default
brightness level after the resume:
this has the effect of having the kernel report wrong brightness
status after a sleep, and on some devices (like the Asus RC71L) that
brightness is the intensity of LEDs directly facing the user.
Fix the above issue by setting back brightness to the level it had
before entering a sleep state.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the function asus_kbd_set_report the parameter buf is read-only
as it gets copied in a memory portion suitable for USB transfer,
but the parameter is not marked as const: add the missing const and mark
const immutable buffers passed to that function.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 9d1bd93462.
Multiple people reported misbehaving devices and reverting this commit fixes
the problem for them. As soon as the original commit author starts reacting
again, we can try to figure out why he hasn't seen the issues (mismatching
report descriptors?), but for the time being, fix for 6.7 by reverting.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218172
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218094
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices disconnect if suspended without remote wakeup. They can operate
with the standard driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Glorious Model I mouse has a buggy HID report descriptor for its
keyboard endpoint (used for programmable buttons). For report ID 2, there
is a mismatch between Logical Minimum and Usage Minimum in the array that
reports keycodes.
The offending portion of the descriptor: (from hid-decode)
0x95, 0x05, // Report Count (5) 30
0x75, 0x08, // Report Size (8) 32
0x15, 0x00, // Logical Minimum (0) 34
0x25, 0x65, // Logical Maximum (101) 36
0x05, 0x07, // Usage Page (Keyboard) 38
0x19, 0x01, // Usage Minimum (1) 40
0x29, 0x65, // Usage Maximum (101) 42
0x81, 0x00, // Input (Data,Arr,Abs) 44
This bug shifts all programmed keycodes up by 1. Importantly, this causes
"empty" array indexes of 0x00 to be interpreted as 0x01, ErrorRollOver.
The presence of ErrorRollOver causes the system to ignore all keypresses
from the endpoint and breaks the ability to use the programmable buttons.
Setting byte 41 to 0x00 fixes this, and causes keycodes to be interpreted
correctly.
Also, USB_VENDOR_ID_GLORIOUS is changed to USB_VENDOR_ID_SINOWEALTH,
and a new ID for Laview Technology is added. Glorious seems to be
white-labeling controller boards or mice from these vendors. There isn't a
single canonical vendor ID for Glorious products.
Signed-off-by: Brett Raye <braye@fastmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jamesdonkey A3R keyboard is identified as "Jamesdonkey A3R" in wired
mode, "A3R-U" in wireless mode and "A3R" in bluetooth mode. Adding them
to non-apple keyboards fixes function key.
Signed-off-by: Yihong Cao <caoyihong4@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a user requests more than 60 bytes of data the MCP2221 must chunk
the data in chunks up to 60 bytes long (see command/response code 0x40
in the datasheet).
In order to signal that the device has more data the (undocumented) byte
at byte index 2 of the Get I2C Data response uses the value 0x54. This
contrasts with the case for the final data chunk where the value
returned is 0x55 (MCP2221_I2C_READ_COMPL). The fact that 0x55 was not
returned in the response was interpreted by the driver as a failure
meaning that all reads of more than 60 bytes would fail.
Add support for reads that are split over multiple chunks by looking for
the response code indicating that more data is expected and continuing
the read as the code intended. Some timing delays are required to ensure
the chip has time to refill its FIFO as data is read in from the I2C
bus. This timing has been tested in my system when configured for bus
speeds of 50KHz, 100KHz, and 400KHz and operates well.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the initial commit of this driver the I2C bus speed has been
reconfigured for every single transfer. This is despite the fact that we
never change the speed and it is never "lost" by the chip.
Upon investigation we find that what was really happening was that the
setting of the bus speed had the side effect of cancelling a previous
failed command if there was one, thereby freeing the bus. This is the
part that was actually required to keep the bus operational in the face
of failed commands.
Instead of always setting the speed, we now correctly cancel any failed
commands as they are detected. This means we can just set the bus speed
at probe time and remove the previous speed sets on each transfer.
This has the effect of improving performance and reducing the number of
commands required to complete transfers.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In scenarios where an I2C device tree is defined in ACPI and exists off
the MCP2221 I2C bus, the devices could not be instantiated.
Mark the USB port that the MCP2221 is connected to as its ACPI companion
so that the USB device can be bound to the ACPI tree when enumerated.
With this change the downstream I2C tree devices can be instantiated on
ACPI systems.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
During the probe we add an I2C adapter and as soon as we add that adapter
it may be used for a transfer (e.g via the code in i2cdetect()).
Those transfers are not able to complete and time out. This is because the
HID raw_event callback (mcp2221_raw_event) will not be invoked until the
HID device's 'driver_input_lock' is marked up at the completion of the
probe in hid_device_probe(). This starves the driver of the responses it
is waiting for.
In order to allow the I2C transfers to complete while we are still in the
probe, start the IO once we have completed init of the HID device.
This issue seems to have been seen before and a patch was submitted but
it seems it was never accepted. See:
https://lore.kernel.org/all/20221103222714.21566-3-Enrik.Berkhan@inka.de/
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The process of adding an I2C adapter can invoke I2C accesses on that new
adapter (see i2c_detect()).
Ensure we have set the adapter's driver data to avoid null pointer
dereferences in the xfer functions during the adapter add.
This has been noted in the past and the same fix proposed but not
completed. See:
https://lore.kernel.org/lkml/ef597e73-ed71-168e-52af-0d19b03734ac@vigem.de/
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added a gpiochip compatible driver to control the 8 GPIOs of
the MCP2200 by using the HID interface.
Using GPIOs with alternative functions (GP0<->SSPND, GP1<->USBCFG,
GP6<->RXLED, GP7<->TXLED) will reset the functions, if set (unset by
default).
The driver was tested while also using the UART of the chip. Setting
and reading the GPIOs has no effect on the UART communication. However,
a reset is triggered after the CONFIGURE command. If the GPIO Direction
is constantly changed, this will affect the communication at low baud
rates. This is a hardware problem of the MCP2200 and is not caused by
the driver.
Signed-off-by: Johannes Roith <johannes@gnu-linux.rocks>
Reviewed-by: Rahul Rameshbabu <sergeantsagara@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUTSzg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylH3QCfbZuG8MiglEZUd4slRLUNqcRQ5tQAn1yKpDFo
l3KLkxo1UTLMXbJBWe+b
=gafK
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (326 commits)
cdx: add sysfs for subsystem, class and revision
cdx: add sysfs for bus reset
cdx: add support for bus enable and disable
cdx: Register cdx bus as a device on cdx subsystem
cdx: Create symbol namespaces for cdx subsystem
cdx: Introduce lock to protect controller ops
cdx: Remove cdx controller list from cdx bus system
dts: ti: k3-am625-beagleplay: Add beaglecc1352
greybus: Add BeaglePlay Linux Driver
dt-bindings: net: Add ti,cc1352p7
dt-bindings: eeprom: at24: allow NVMEM cells based on old syntax
dt-bindings: nvmem: SID: allow NVMEM cells based on old syntax
Revert "nvmem: add new config option"
MAINTAINERS: coresight: Add missing Coresight files
misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
firmware: xilinx: Move EXPORT_SYMBOL_GPL next to zynqmp_pm_feature definition
uacce: make uacce_class constant
ocxl: make ocxl_class constant
cxl: make cxl_class constant
misc: phantom: make phantom_class constant
...
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver
-----BEGIN PGP SIGNATURE-----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=l79u
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Highlights:
- AMD adds some more upcoming HW platforms
- Intel made Meteorlake stable and started adding Lunarlake
- nouveau has a bunch of display rework in prepartion for the NVIDIA
GSP firmware support
- msm adds a7xx support
- habanalabs has finished migration to accel subsystem
Detail summary:
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver"
* tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm: (1803 commits)
drm/amdgpu: Remove unused variables from amdgpu_show_fdinfo
drm/amdgpu: Remove duplicate fdinfo fields
drm/amd/amdgpu: avoid to disable gfxhub interrupt when driver is unloaded
drm/amdgpu: Add EXT_COHERENT support for APU and NUMA systems
drm/amdgpu: Retrieve CE count from ce_count_lo_chip in EccInfo table
drm/amdgpu: Identify data parity error corrected in replay mode
drm/amdgpu: Fix typo in IP discovery parsing
drm/amd/display: fix S/G display enablement
drm/amdxcp: fix amdxcp unloads incompletely
drm/amd/amdgpu: fix the GPU power print error in pm info
drm/amdgpu: Use pcie domain of xcc acpi objects
drm/amd: check num of link levels when update pcie param
drm/amdgpu: Add a read to GFX v9.4.3 ring test
drm/amd/pm: call smu_cmn_get_smc_version in is_mode1_reset_supported.
drm/amdgpu: get RAS poison status from DF v4_6_2
drm/amdgpu: Use discovery table's subrevision
drm/amd/display: 3.2.256
drm/amd/display: add interface to query SubVP status
drm/amd/display: Read before writing Backlight Mode Set Register
drm/amd/display: Disable SYMCLK32_SE RCO on DCN314
...
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R. Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)
-----BEGIN PGP SIGNATURE-----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=0iVF
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
hid_connect() will call hid_pidff_init() which does
hid_device_io_start() leading to an "io already started" warning.
To fix this call hid_device_io_stop() before calling hid_connect(),
stopping IO means that connect events may be lost while hid_connect()
runs, re-enable IO and move the hidpp_connect_event() work queuing
after the hid_connect().
Note re-enabling IO is also necessary for the g920_get_config()
call later during hidpp_probe().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231025190151.302376-1-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
HIDPP unifying is only checked once in probe() and it is also
set by probe() itself.
Drop the quirk and replace its one check by the condition which is
used to set the quirk in the first place.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-13-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Drop delayed_work_cb() instead make hidpp_connect_event() the workqueue
function itself.
Besides resulting in a small cleanup this will hopefully also make
it clearer that going forward hidpp_connect_event() should only
be run from a workqueue and not be directly invoked.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-12-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
There is a connect event race in hidpp_probe() in these 2 lines:
connected = hidpp_root_get_protocol_version(hidpp) == 0;
atomic_set(&hidpp->connected, connected);
Specifically the following can happen:
1. This line from hidpp_probe() is executed:
connected = hidpp_root_get_protocol_version(hidpp) == 0;
and sets connected to false;
2. A connect-event packet is received and does:
atomic_set(&hidpp->connected, true);
3. The next line from hidpp_probe() is executed:
atomic_set(&hidpp->connected, connected);
and sets the atomic_t back to 0 again.
4. hidpp_connect_event() runs and sees the connected device
as disconnected because of this.
To fix this make hidpp_connect_event() query the connection status
of the device itself instead of having it rely on possibly stale
data cached in struct hidpp_device.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-11-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Remove the unused connected function parameter from wtp_connect(),
m560_send_config_command() and k400_connect().
This is a preparation patch for moving all connected state handling
to hidpp_connect_event().
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-10-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Turn hidpp_overwrite_name() into a hidpp_non_unifying_init() helper
which takes care of setting both the name and the serial for non
unifying devices.
This mirrors the hidpp_unifying_init() helper for unifying devices.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-8-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Move the hidpp_overwrite_name() call to before the connect check, this
puts it at the same place in the probe() order as hidpp_serial_init()
which seems more logical. This should not make a difference since this
is in the non-unifying path and only unifying devices can be probed
in non-connected state.
This is a preparation patch for moving all connected state handling
to hidpp_connect_event().
Doing this before the connect check requires dropping the protocol
version check since protocol_major is not set yet now. Instead
this relies on hidpp_root_get_feature(HIDPP_PAGE_GET_DEVICE_NAME_TYPE)
failing on older devices, just like how hidpp_get_serial() relies on
hidpp_root_get_feature(HIDPP_PAGE_DEVICE_INFORMATION) failing on older
devices. So this again makes the code more consistent.
Also stop printing an error on failure now, since with the proto
version check gone failures are expected to happen on older devices.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-7-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The data retrieved by g920_get_config() is only used by hidpp_ff_init().
Now that the hw is kept open till the end of probe() the g920_get_config()
call can be moved to just before hidpp_ff_init() to have all
the HIDPP_QUIRK_CLASS_G920 together in a single place.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-6-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
For WTP devices which start disconnected (paired with the unifying
receiver, but not connected atm) hidpp_connect_event() takes care
of calling wtp_get_config() when the device later connects.
There is no need to have a separate code path for WTP devices which
are connected at probe() time, these can use the same code-path since
probe() will queue hidpp_connect_event() for those at probe time.
Drop the unnecessary wtp_get_config() call from probe().
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-5-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Calling get_wireless_feature_index() from probe() causes
the wireless_feature_index to only get set for unifying devices which
are already connected at probe() time. It does not get set for devices
which connect later.
Fix this by moving get_wireless_feature_index() to hidpp_connect_event(),
this does not make a difference for devices connected at probe() since
probe() will queue the hidpp_connect_event() for those at probe time.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Fixes: 0da0a63b7c ("HID: logitech-hidpp: Support WirelessDeviceStatus connect events")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-4-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Commit 91cf9a98ae ("HID: logitech-hidpp: make .probe usbhid capable")
makes hidpp_probe() first call hid_hw_start(hdev, 0) to allow IO
without connecting any hid subdrivers (hid-input, hidraw).
This is done to allow to retrieve the device's name and serial number
and store these in hdev->name and hdev->uniq.
Then later on IO was stopped and started again with hid_hw_start(hdev,
HID_CONNECT_DEFAULT) connecting hid-input and hidraw after the name
and serial number have been setup.
Commit 498ba20690 ("HID: logitech-hidpp: Don't restart communication
if not necessary") changed the probe() code to only do the start with
a 0 connect-mask + restart later for unifying devices.
But for non unifying devices hdev->name and hdev->uniq are updated too.
So this change re-introduces the problem for which the start with
a 0 connect-mask + restart later behavior was introduced.
The previous patch in this series changes the unifying path to instead of
restarting IO only call hid_connect() later. This avoids possible issues
with restarting IO seen on non unifying devices.
Revert the change to limit the restart behavior to unifying devices to
fix hdev->name changing after userspace facing devices have already been
registered.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Fixes: 498ba20690 ("HID: logitech-hidpp: Don't restart communication if not necessary")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-3-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Restarting IO causes 2 problems:
1. Some devices do not like IO being restarted this was addressed in
commit 498ba20690 ("HID: logitech-hidpp: Don't restart communication
if not necessary"), but that change has issues of its own and needs to
be reverted.
2. Restarting IO and specifically calling hid_device_io_stop() causes
received packets to be missed, which may cause connect-events to
get missed.
Restarting IO was introduced in commit 91cf9a98ae ("HID: logitech-hidpp:
make .probe usbhid capable") to allow to retrieve the device's name and
serial number and store these in hdev->name and hdev->uniq before
connecting any hid subdrivers (hid-input, hidraw) exporting this info
to userspace.
But this does not require restarting IO, this merely requires deferring
calling hid_connect(). Calling hid_hw_start() with a connect-mask of
0 makes it skip calling hid_connect(), so hidpp_probe() can simply call
hid_connect() later without needing to restart IO.
Remove the stop + restart of IO and instead just call hid_connect() later
to avoid the issues caused by restarting IO.
Now that IO is no longer stopped, hid_hw_close() must be called at the end
of probe() to balance the hid_hw_open() done at the beginning probe().
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Fixes: 498ba20690 ("HID: logitech-hidpp: Don't restart communication if not necessary")
Suggested-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-2-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Through the usage of pm_ptr() the CONFIG_PM-dependent code will always be
compiled, protecting against bitrot.
The linker will then garbage-collect the unused function avoiding any overhead.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20231012-hid-pm_ptr-v1-4-0a71531ca93b@weissschuh.net
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Through the usage of pm_ptr() the CONFIG_PM-dependent code will always be
compiled, protecting against bitrot.
The linker will then garbage-collect the unused function avoiding any overhead.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20231012-hid-pm_ptr-v1-3-0a71531ca93b@weissschuh.net
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Through the usage of pm_ptr() the CONFIG_PM-dependent code will always be
compiled, protecting against bitrot.
The linker will then garbage-collect the unused function avoiding any overhead.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20231012-hid-pm_ptr-v1-2-0a71531ca93b@weissschuh.net
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The USB Compact Keyboard variant requires a reset_resume function to
restore keyboard configuration after a suspend in some situations. Move
configuration normally done on probe to lenovo_features_set_cptkbd(), then
recycle this for use on reset_resume.
Without, the keyboard and driver would end up in an inconsistent state,
breaking middle-button scrolling amongst other problems, and twiddling
sysfs values wouldn't help as the middle-button mode won't be set until
the driver is reloaded.
Tested on a USB and Bluetooth Thinkpad Compact Keyboard.
CC: stable@vger.kernel.org
Fixes: 94eefa2713 ("HID: lenovo: Use native middle-button mode for compact keyboards")
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Link: https://lore.kernel.org/r/20231002150914.22101-1-martink@posteo.de
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Previously cp2112_gpio_irq_shutdown() always cancelled the
gpio_poll_worker, even if other IRQs were still active, and did not set
the gpio_poll flag to false. This resulted in any call to _shutdown()
resulting in interrupts no longer functioning on the chip until a
_remove() occurred (a.e. the cp2112 is unplugged or system rebooted).
Only cancel polling if all IRQs are disabled/masked, and correctly set
the gpio_poll flag, allowing polling to restart when an interrupt is
next enabled.
Signed-off-by: Danny Kaehn <danny.kaehn@plexus.com>
Fixes: 13de9cca51 ("HID: cp2112: add IRQ chip handling")
Link: https://lore.kernel.org/r/20231011182317.1053344-1-danny.kaehn@plexus.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmU1ngkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrsIH/0k/+gdBBYFFdEym
foRhKir9WV3ZX4oIozJjA1f7T+qVYclKs6kaYm3gNepRBb6AoG8pdgv4MMAqhYsf
QMe2XHi0MrO/qKBgfNfivxEa9jq+0QK5uvTbqCRqCAB8LfwVyDqapCmg3EuiZcPW
UbMITmnwLIfXgPxvp9rabmCsTqO6FLbf0GDOVIkNSAIDBXMpcO1iffjrWUbhRa7n
oIoiJmWJLcXLxPWDsRKbpJwzw2cIG08YhfQYAiQnC3YaeRm1FKLDIICRBsmfYzja
rWv9r4dn4TDfV4/AnjggQnsZvz2yPCxNaFSQIT88nIeiLvyuUTJ9j8aidsSfMZQf
xZAbzbA=
=NoQv
-----END PGP SIGNATURE-----
BackMerge tag 'v6.6-rc7' into drm-next
This is needed to add the msm pr which is based on a higher base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
-----BEGIN PGP SIGNATURE-----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=wth0
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 1st set of new device support, features and cleanup for 6.7
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
* tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (201 commits)
iio: Use device_get_match_data()
iio: adc: MCP3564: fix warn: unsigned '__x' is never less than zero.
dt-bindings: trivial-devices: add silabs,si7005
iio: si7005: Add device tree support
drivers: imu: adis16475.c: Remove scan index from delta channels
dt-bindings: iio: imu: st,lsm6dsx: add mount-matrix property
iio: resolver: ad2s1210: remove of_match_ptr()
iio: resolver: ad2s1210: remove DRV_NAME macro
iio: resolver: ad2s1210: move out of staging
staging: iio: resolver: ad2s1210: simplify code with guard(mutex)
staging: iio: resolver: ad2s1210: clear faults after soft reset
staging: iio: resolver: ad2s1210: refactor sample toggle
staging: iio: resolver: ad2s1210: remove fault attribute
staging: iio: resolver: ad2s1210: add label attribute support
staging: iio: resolver: ad2s1210: add register/fault support summary
staging: iio: resolver: ad2s1210: implement fault events
iio: event: add optional event label support
staging: iio: resolver: ad2s1210: rename DOS reset min/max attrs
staging: iio: resolver: ad2s1210: convert DOS mismatch threshold to event attr
staging: iio: resolver: ad2s1210: convert DOS overrange threshold to event attr
...
hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU)
races when it races with itself.
hidpp_connect_event() primarily runs from a workqueue but it also runs
on probe() and if a "device-connected" packet is received by the hw
when the thread running hidpp_connect_event() from probe() is waiting on
the hw, then a second thread running hidpp_connect_event() will be
started from the workqueue.
This opens the following races (note the below code is simplified):
1. Retrieving + printing the protocol (harmless race):
if (!hidpp->protocol_major) {
hidpp_root_get_protocol_version()
hidpp->protocol_major = response.rap.params[0];
}
We can actually see this race hit in the dmesg in the abrt output
attached to rhbz#2227968:
[ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
[ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
Testing with extra logging added has shown that after this the 2 threads
take turn grabbing the hw access mutex (send_mutex) so they ping-pong
through all the other TOCTOU cases managing to hit all of them:
2. Updating the name to the HIDPP name (harmless race):
if (hidpp->name == hdev->name) {
...
hidpp->name = new_name;
}
3. Initializing the power_supply class for the battery (problematic!):
hidpp_initialize_battery()
{
if (hidpp->battery.ps)
return 0;
probe_battery(); /* Blocks, threads take turns executing this */
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
}
4. Creating delayed input_device (potentially problematic):
if (hidpp->delayed_input)
return;
hidpp->delayed_input = hidpp_allocate_input(hdev);
The really big problem here is 3. Hitting the race leads to the following
sequence:
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
...
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
So now we have registered 2 power supplies for the same battery,
which looks a bit weird from userspace's pov but this is not even
the really big problem.
Notice how:
1. This is all devm-maganaged
2. The hidpp->battery.desc struct is shared between the 2 power supplies
3. hidpp->battery.desc.properties points to the result from the second
devm_kmemdup()
This causes a use after free scenario on USB disconnect of the receiver:
1. The last registered power supply class device gets unregistered
2. The memory from the last devm_kmemdup() call gets freed,
hidpp->battery.desc.properties now points to freed memory
3. The first registered power supply class device gets unregistered,
this involves sending a remove uevent to userspace which invokes
power_supply_uevent() to fill the uevent data
4. power_supply_uevent() uses hidpp->battery.desc.properties which
now points to freed memory leading to backtraces like this one:
Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08
...
Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event
Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0
...
Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0
Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0
Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680
Sep 22 20:01:35 eric kernel: power_supply_unregister+0x8e/0xa0
Sep 22 20:01:35 eric kernel: release_nodes+0x3d/0xb0
Sep 22 20:01:35 eric kernel: devres_release_group+0xfc/0x130
Sep 22 20:01:35 eric kernel: hid_device_remove+0x56/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: logi_dj_remove+0x9a/0x100 [hid_logitech_dj 5c91534a0ead2b65e04dd799a0437e3b99b21bc4]
Sep 22 20:01:35 eric kernel: hid_device_remove+0x44/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: usbhid_disconnect+0x47/0x60 [usbhid 727dcc1c0b94e6b4418727a468398ac3bca492f3]
Sep 22 20:01:35 eric kernel: usb_unbind_interface+0x90/0x270
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? kobject_put+0xa0/0x1d0
Sep 22 20:01:35 eric kernel: usb_disable_device+0xcd/0x1e0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xde/0x2c0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xc3/0x2c0
Sep 22 20:01:35 eric kernel: hub_event+0xe80/0x1c10
There have been quite a few bug reports (see Link tags) about this crash.
Fix all the TOCTOU issues, including the really bad power-supply related
system crash on USB disconnect, by making probe() use the workqueue for
running hidpp_connect_event() too, so that it can never run more then once.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227221
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2242189
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412#c58
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231005182638.3776-1-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
A recent commit reordered probe so that the interrupt line is now
requested before making sure that the device exists.
This breaks machines like the Lenovo ThinkPad X13s which rely on the
HID driver to probe second-source devices and only register the variant
that is actually populated. Specifically, the interrupt line may now
already be (temporarily) claimed when doing asynchronous probing of the
touchpad:
genirq: Flags mismatch irq 191. 00082008 (hid-over-i2c) vs. 00082008 (hid-over-i2c)
i2c_hid_of 21-0015: Could not register for hid-over-i2c interrupt, irq = 191, ret = -16
i2c_hid_of: probe of 21-0015 failed with error -16
Fix this by restoring the old behaviour of first making sure the device
exists before requesting the interrupt line.
Note that something like this should probably be implemented also for
"panel followers", whose actual probe is currently effectively deferred
until the DRM panel is probed (e.g. by powering down the device after
making sure it exists and only then register it as a follower).
Fixes: 675cd877c9 ("HID: i2c-hid: Rearrange probe() to power things up later")
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20231002155857.24584-1-johan+linaro@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Like various other devices using similar hardware, this model reports a
perpetually empty battery (0-1%).
Join the others and apply HID_BATTERY_QUIRK_IGNORE.
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
service, which allows to wakup device when the system is in S5 (Soft-Off
state). This OOB service can be enabled/disabled from BIOS settings. When
enabled, the ISH device gets PME wake capability. To enable PME wakeup,
driver also needs to enable ACPI GPE bit.
On resume, BIOS will clear the wakeup bit. So driver need to re-enable it
in resume function to keep the next wakeup capability. But this BIOS
clearing of wakeup bit doesn't decrement internal OS GPE reference count,
so this reenabling on every resume will cause reference count to overflow.
So first disable and reenable ACPI GPE bit using acpi_disable_gpe().
Fixes: 2e23a70eda ("HID: intel-ish-hid: ipc: finish power flow for EHL OOB")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://lore.kernel.org/lkml/CAAd53p4=oLYiH2YbVSmrPNj1zpMcfp=Wxbasb5vhMXOWCArLCg@mail.gmail.com/T/
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usb_free_urb() does the NULL check itself, so there is no need to duplicate
it prior to calling.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1cd4004cd ("HID: sony: Fix a potential memory leak in sony_probe()")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When suspending the computer, a Switch Pro Controller connected via USB will
lose its internal status. However, because the USB connection was technically
never lost, when resuming the computer, the driver will attempt to communicate
with the controller as if nothing happened (and fail).
Because of this, the user was forced to manually disconnect the controller
(or to press the sync button on the controller to power it off), so that it
can be re-initialized.
With this patch, the controller will be automatically re-initialized after
resuming from suspend.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216233
Signed-off-by: Martino Fontana <tinozzo123@gmail.com>
Reviewed-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit in Fixes updated the error handling path of
thunderstrike_create() and the remove function but not the error handling
path of shield_probe(), should an error occur after a successful
thunderstrike_create() call.
Add the missing calls.
Fixes: 3ab196f882 ("HID: nvidia-shield: Add battery support for Thunderstrike")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit in Fixes updated the error handling path of
thunderstrike_create() and the remove function but not the error handling
path of shield_probe(), should an error occur after a successful
thunderstrike_create() call.
Add the missing call. Make sure it is safe to call in the probe error
handling path by preventing the led_classdev from attempting to set the LED
brightness to the off state on unregister.
Fixes: f88af60e74 ("HID: nvidia-shield: Support LED functionality for Thunderstrike")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Register the Synaptics device as a special multitouch device with certain
quirks that may improve usability of the touchpad device.
Reported-by: Rain <rain@sunshowers.io>
Closes: https://lore.kernel.org/linux-input/2bbb8e1d-1793-4df1-810f-cb0137341ff4@app.fastmail.com/
Signed-off-by: Rahul Rameshbabu <sergeantsagara@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously the cp2112 driver called INIT_DELAYED_WORK within
cp2112_gpio_irq_startup, resulting in duplicate initilizations of the
workqueue on subsequent IRQ startups following an initial request. This
resulted in a warning in set_work_data in workqueue.c, as well as a rare
NULL dereference within process_one_work in workqueue.c.
Initialize the workqueue within _probe instead.
Fixes: 13de9cca51 ("HID: cp2112: add IRQ chip handling")
Signed-off-by: Danny Kaehn <danny.kaehn@plexus.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Support player LED patterns up to 8 players.
(Note that the behavior still consinsts in increasing the player number
every time a controller is connected, never decreasing it. It should be
as is described in https://bugzilla.kernel.org/show_bug.cgi?id=216225.
However, any implementation here would stop making sense as soon as a
non-Nintendo controller is connected, which is why I'm not bothering.)
- Split part of `joycon_home_led_brightness_set` (which is called by hid)
into `joycon_set_home_led` (which is what actually sets the LEDs), for
consistency with player LEDs.
- `joycon_player_led_brightness_set` won't try it to "determine which
player led this is" anymore: it's already looking at every LED
brightness value.
- Instead of first registering the `led_classdev`, then attempting to set
the LED and unregistering the `led_classdev` if it fails, first attempt
to set the LED, then register the `led_classdev` only if it succeeds
(the class is still filled up in either case).
- If setting the player LEDs fails, still attempt setting the home LED.
(I don't know there's a third party controller where this may actually
happen, but who knows...)
- Use `JC_NUM_LEDS` where appropriate instead of 4.
- Print return codes in more places.
- Use spinlock instead of mutex for `input_num`. Copy its value to a local
variable, so that it can be unlocked immediately.
- `input_num` starts counting from 0
- Less holding of mutexes in general.
Signed-off-by: Martino Fontana <tinozzo123@gmail.com>
Reviewed-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Built-in firmware of cptkbd handles scrolling by itself (when middle
button is pressed) but with issues: it does not support horizontal and
hi-res scrolling and upon middle button release it sends middle button
click even if there was a scrolling event. Commit 3cb5ff0220 ("HID:
lenovo: Hide middle-button press until release") workarounds last
issue but it's impossible to workaround scrolling-related issues
without firmware modification.
Likely, Dennis Schneider has reverse engineered the firmware and
provided an instruction on how to patch it [1]. However,
aforementioned workaround prevents userspace (libinput) from knowing
exact moment when middle button has been pressed down and performing
"On-Button scrolling". This commit detects correctly-behaving patched
firmware if cursor movement events has been received during middle
button being pressed and stops applying workaround for this device.
Link: https://hohlerde.org/rauch/en/elektronik/projekte/tpkbd-fix/ [1]
Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In order to simplify some error handling paths and avoid code duplication,
introduce thunderstrike_destroy() which undoes thunderstrike_create().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit in Fixes updated the error handling path of
thunderstrike_create() and the remove function but not the error handling
path of shield_probe(), should an error occur after a successful
thunderstrike_create() call.
Add the missing calls.
Fixes: 3ab196f882 ("HID: nvidia-shield: Add battery support for Thunderstrike")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit in Fixes updated the error handling path of
thunderstrike_create() and the remove function but not the error handling
path of shield_probe(), should an error occur after a successful
thunderstrike_create() call.
Add the missing call. Make sure it is safe to call in the probe error
handling path by preventing the led_classdev from attempting to set the LED
brightness to the off state on unregister.
Fixes: f88af60e74 ("HID: nvidia-shield: Support LED functionality for Thunderstrike")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery information reported by the driver depends on the power supply
subsystem. Select the required subsystem when the HID_NVIDIA_SHIELD Kconfig
option is enabled.
Fixes: 3ab196f882 ("HID: nvidia-shield: Add battery support for Thunderstrike")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In most cases, ambient color sensors also support the x and y light
colors, which represent the coordinates on the CIE 1931 chromaticity
diagram. Thus, add light chromaticity x and y for SFH1.1.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/20230919081054.2050714-10-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support the x and y light
colors, which represent the coordinates on the CIE 1931 chromaticity
diagram. Thus, add light chromaticity x and y.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/20230919081054.2050714-9-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support light color temperature.
As a result, add support of light color temperature for SFH1.1.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/20230919081054.2050714-6-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support light color temperature.
As a result, add support of light color temperature.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/20230919081054.2050714-5-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
There is a slab-out-of-bounds Write bug in hid-holtek-kbd driver.
The problem is the driver assumes the device must have an input
but some malicious devices violate this assumption.
Fix this by checking hid_device's input is non-empty before its usage.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid-nvidia-shield driver uses functions that are built
only when LEDS_CLASS is set, so make the driver depend on that
symbol to prevent build errors.
riscv32-linux-ld: drivers/hid/hid-nvidia-shield.o: in function `.L11':
hid-nvidia-shield.c:(.text+0x192): undefined reference to `led_classdev_unregister'
riscv32-linux-ld: drivers/hid/hid-nvidia-shield.o: in function `.L113':
hid-nvidia-shield.c:(.text+0xfa4): undefined reference to `led_classdev_register_ext'
Fixes: 09308562d4 ("HID: nvidia-shield: Initial driver implementation with Thunderstrike support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Using hidpp for the M720 adds battery info reporting and hires
scrolling support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid_hw_raw_request() function returns negative error codes or the
number bytes transferred. The problem is that when it returns negative
error codes and we check if "ret < sizeof(arctis_1_battery_request)",
then the negative values are type promoted from int to high unsigned long
values and treated as success.
This was detected using Smatch:
drivers/hid/hid-steelseries.c:393 steelseries_headset_arctis_1_fetch_battery()
warn: error code type promoted to positive: 'ret'
Fixes: a0c76896c3 ("HID: steelseries: Add support for Arctis 1 XBox")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Generate callback functions for struct fb_ops with the fbdev macro
FB_GEN_DEFAULT_DEFERRED_SYSMEM_OPS(). Initialize struct fb_ops to
the generated functions with an fbdev initializer macro.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230828132131.29295-7-tzimmermann@suse.de
If an error occurs after a successful usb_alloc_urb() call, usb_free_urb()
should be called.
Fixes: fb1a79a6b6 ("HID: sony: fix freeze when inserting ghlive ps3/wii dongles")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----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=24SV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2023083101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Benjamin Tissoires:
- devm fixes for problems that caused use-after-free reports (Rahul
Rameshbabu)
- Some extensive HID docs (Marco Morandini)
- Constification of struct class (Ivan Orlov and Greg Kroah-Hartman)
- Google Stadia Force Feedback support (Fabio Baltieri)
- Various fixes and new device ID support
* tag 'for-linus-2023083101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (42 commits)
HID: logitech-hidpp: rework one more time the retries attempts
HID: nvidia-shield: Reference hid_device devm allocation of input_dev name
HID: multitouch: Correct devm device reference for hidinput input_dev name
HID: uclogic: Correct devm device reference for hidinput input_dev name
HID: logitech-dj: Fix error handling in logi_dj_recv_switch_to_dj_mode()
HID: i2c-hid: elan: Add ili9882t timing
dt-bindings: input: i2c-hid: Introduce Ilitek ili9882t
HID: apple: Add "Hailuck" to the list of non-apple keyboards
HID: steelseries: arctis_1_battery_request[] should be static
MAINTAINERS: update my email address
HID: logitech-hidpp: Add support for Logitech MX Anywhere 3 mouse
HID: wacom: struct name cleanup
HID: wacom: remove unnecessary 'connected' variable from EKR
HID: wacom: remove the battery when the EKR is off
HID: nvidia-shield: Update Thunderstrike LED instance name to use id
HID: nvidia-shield: Add battery support for Thunderstrike
HID: nvidia-shield: Remove led_classdev_unregister in thunderstrike_create
HID: hid-google-stadiaff: add support for Stadia force feedback
HID: logitech-dj: Add support for a new lightspeed receiver iteration
HID: logitech-hidpp: Add support for the Pro X Superlight
...
Here is a small set of driver core updates and additions for 6.6-rc1.
Included in here are:
- stable kernel documentation updates
- class structure const work from Ivan on various subsystems
- kernfs tweaks
- driver core tests!
- kobject sanity cleanups
- kobject structure reordering to save space
- driver core error code handling fixups
- other minor driver core cleanups
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH77Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZMACePk8SitfaJc6FfFf5I7YK7Nq0V8MAn0nUjgsR
i8NcNpu/Yv4HGrDgTdh/
=PJbk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core updates and additions for 6.6-rc1.
Included in here are:
- stable kernel documentation updates
- class structure const work from Ivan on various subsystems
- kernfs tweaks
- driver core tests!
- kobject sanity cleanups
- kobject structure reordering to save space
- driver core error code handling fixups
- other minor driver core cleanups
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
driver core: Call in reversed order in device_platform_notify_remove()
driver core: Return proper error code when dev_set_name() fails
kobject: Remove redundant checks for whether ktype is NULL
kobject: Add sanity check for kset->kobj.ktype in kset_register()
drivers: base: test: Add missing MODULE_* macros to root device tests
drivers: base: test: Add missing MODULE_* macros for platform devices tests
drivers: base: Free devm resources when unregistering a device
drivers: base: Add basic devm tests for platform devices
drivers: base: Add basic devm tests for root devices
kernfs: fix missing kernfs_iattr_rwsem locking
docs: stable-kernel-rules: mention that regressions must be prevented
docs: stable-kernel-rules: fine-tune various details
docs: stable-kernel-rules: make the examples for option 1 a proper list
docs: stable-kernel-rules: move text around to improve flow
docs: stable-kernel-rules: improve structure by changing headlines
base/node: Remove duplicated include
kernfs: attach uuid for every kernfs and report it in fsid
kernfs: add stub helper for kernfs_generic_poll()
x86/resctrl: make pseudo_lock_class a static const structure
x86/MSR: make msr_class a static const structure
...
core:
- fix gfp flags in drmm_kmalloc
gpuva:
- add new generic GPU VA manager (for nouveau initially)
syncobj:
- add new DRM_IOCTL_SYNCOBJ_EVENTFD ioctl
dma-buf:
- acquire resv lock for mmap() in exporters
- support dma-buf self import automatically
- docs fixes
backlight:
- fix fbdev interactions
atomic:
- improve logging
prime:
- remove struct gem_prim_mmap plus driver updates
gem:
- drm_exec: add locking over multiple GEM objects
- fix lockdep checking
fbdev:
- make fbdev userspace interfaces optional
- use linux device instead of fbdev device
- use deferred i/o helper macros in various drivers
- Make FB core selectable without drivers
- Remove obsolete flags FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT
- Add helper macros and Kconfig tokens for DMA-allocated framebuffer
ttm:
- support init_on_free
- swapout fixes
panel:
- panel-edp: Support AUO B116XAB01.4
- Support Visionox R66451 plus DT bindings
- ld9040: Backlight support, magic improved,
Kconfig fix
- Convert to of_device_get_match_data()
- Fix Kconfig dependencies
- simple: Set bpc value to fix warning; Set connector type for AUO T215HVN01;
Support Innolux G156HCE-L01 plus DT bindings
- ili9881: Support TDO TL050HDV35 LCD panel plus DT bindings
- startek: Support KD070FHFID015 MIPI-DSI panel plus DT bindings
- sitronix-st7789v: Support Inanbo T28CP45TN89 plus DT bindings;
Support EDT ET028013DMA plus DT bindings; Various cleanups
- edp: Add timings for N140HCA-EAC
- Allow panels and touchscreens to power sequence together
- Fix Innolux G156HCE-L01 LVDS clock
bridge:
- debugfs for chains support
- dw-hdmi: Improve support for YUV420 bus format
CEC suspend/resume, update EDID on HDMI detect
- dw-mipi-dsi: Fix enable/disable of DSI controller
- lt9611uxc: Use MODULE_FIRMWARE()
- ps8640: Remove broken EDID code
- samsung-dsim: Fix command transfer
- tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
- adv7511: Fix low refresh rate
- anx7625: Switch to macros instead of hardcoded values
locking fixes
- tc358767: fix hardware delays
- sitronix-st7789v: Support panel orientation; Support rotation
property; Add support for Jasonic
JT240MHQS-HWT-EK-E3 plus DT bindings
amdgpu:
- SDMA 6.1.0 support
- HDP 6.1 support
- SMUIO 14.0 support
- PSP 14.0 support
- IH 6.1 support
- Lots of checkpatch cleanups
- GFX 9.4.3 updates
- Add USB PD and IFWI flashing documentation
- GPUVM updates
- RAS fixes
- DRR fixes
- FAMS fixes
- Virtual display fixes
- Soft IH fixes
- SMU13 fixes
- Rework PSP firmware loading for other IPs
- Kernel doc fixes
- DCN 3.0.1 fixes
- LTTPR fixes
- DP MST fixes
- DCN 3.1.6 fixes
- SMU 13.x fixes
- PSP 13.x fixes
- SubVP fixes
- GC 9.4.3 fixes
- Display bandwidth calculation fixes
- VCN4 secure submission fixes
- Allow building DC on RISC-V
- Add visible FB info to bo_print_info
- HBR3 fixes
- GFX9 MCBP fix
- GMC10 vmhub index fix
- GMC11 vmhub index fix
- Create a new doorbell manager
- SR-IOV fixes
- initial freesync panel replay support
- revert zpos properly until igt regression is fixeed
- use TTM to manage doorbell BAR
- Expose both current and average power via hwmon if supported
amdkfd:
- Cleanup CRIU dma-buf handling
- Use KIQ to unmap HIQ
- GFX 9.4.3 debugger updates
- GFX 9.4.2 debugger fixes
- Enable cooperative groups fof gfx11
- SVM fixes
- Convert older APUs to use dGPU path like newer APUs
- Drop IOMMUv2 path as it is no longer used
- TBA fix for aldebaran
i915:
- ICL+ DSI modeset sequence
- HDCP improvements
- MTL display fixes and cleanups
- HSW/BDW PSR1 restored
- Init DDI ports in VBT order
- General display refactors
- Start using plane scale factor for relative data rate
- Use shmem for dpt objects
- Expose RPS thresholds in sysfs
- Apply GuC SLPC min frequency softlimit correctly
- Extend Wa_14015795083 to TGL, RKL, DG1 and ADL
- Fix a VMA UAF for multi-gt platform
- Do not use stolen on MTL due to HW bug
- Check HuC and GuC version compatibility on MTL
- avoid infinite GPU waits due to premature release
of request memory
- Fixes and updates for GSC memory allocation
- Display SDVO fixes
- Take stolen handling out of FBC code
- Make i915_coherent_map_type GT-centric
- Simplify shmem_create_from_object map_type
msm:
- SM6125 MDSS support
- DPU: SM6125 DPU support
- DSI: runtime PM support, burst mode support
- DSI PHY: SM6125 support in 14nm DSI PHY driver
- GPU: prepare for a7xx
- fix a690 firmware
- disable relocs on a6xx and newer
radeon:
- Lots of checkpatch cleanups
ast:
- improve device-model detection
- Represent BMV as virtual connector
- Report DP connection status
nouveau:
- add new exec/bind interface to support Vulkan
- document some getparam ioctls
- improve VRAM detection
- various fixes/cleanups
- workraound DPCD issues
ivpu:
- MMU updates
- debugfs support
- Support vpu4
virtio:
- add sync object support
atmel-hlcdc:
- Support inverted pixclock polarity
etnaviv:
- runtime PM cleanups
- hang handling fixes
exynos:
- use fbdev DMA helpers
- fix possible NULL ptr dereference
komeda:
- always attach encoder
omapdrm:
- use fbdev DMA helpers
ingenic:
- kconfig regmap fixes
loongson:
- support display controller
mediatek:
- Small mtk-dpi cleanups
- DisplayPort: support eDP and aux-bus
- Fix coverity issues
- Fix potential memory leak if vmap() fail
mgag200:
- minor fixes
mxsfb:
- support disabling overlay planes
panfrost:
- fix sync in IRQ handling
ssd130x:
- Support per-controller default resolution plus DT bindings
- Reduce memory-allocation overhead
- Improve intermediate buffer size computation
- Fix allocation of temporary buffers
- Fix pitch computation
- Fix shadow plane allocation
tegra:
- use fbdev DMA helpers
- Convert to devm_platform_ioremap_resource()
- support bridge/connector
- enable PM
tidss:
- Support TI AM625 plus DT bindings
- Implement new connector model plus driver updates
vkms:
- improve write back support
- docs fixes
- support gamma LUT
zynqmp-dpsub:
- misc fixes
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEEKbZHaGwW9KfbeusDHTzWXnEhr4FAmTukSYACgkQDHTzWXnE
hr6vnQ/+J7vBVkBr8JsaEV/twcZwzbNdpivsIagd8U83GQB50nDReVXbNx+Wo0/C
WiGlrC6Sw3NVOGbkigd5IQ7fb5C/7RnBmzMi/iS7Qnk2uEqLqgV00VxfGwdm6wgr
0gNB8zuu2xYphHz2K8LzwnmeQRdN+YUQpUa2wNzLO88IEkTvq5vx2rJEn5p9/3hp
OxbbPBzpDRRPlkNFfVQCN8todbKdsPc4am81Eqgv7BJf21RFgQodPGW5koCYuv0w
3m+PJh1KkfYAL974EsLr/pkY7yhhiZ6SlFLX8ssg4FyZl/Vthmc9bl14jRq/pqt4
GBp8yrPq1XjrwXR8wv3MiwNEdANQ+KD9IoGlzLxqVgmEFRE+g4VzZZXeC3AIrTVP
FPg4iLUrDrmj9RpJmbVqhq9X2jZs+EtRAFkJPrPbq2fItAD2a2dW4X3ISSnnTqDI
6O2dVwuLCU6OfWnvN4bPW9p8CqRgR8Itqv1SI8qXooDy307YZu1eTUf5JAVwG/SW
xbDEFVFlMPyFLm+KN5dv1csJKK21vWi9gLg8phK8mTWYWnqMEtJqbxbRzmdBEFmE
pXKVu01P6ZqgBbaETpCljlOaEDdJnvO4W+o70MgBtpR2IWFMbMNO+iS0EmLZ6Vgj
9zYZctpL+dMuHV0Of1GMkHFRHTMYEzW4tuctLIQfG13y4WzyczY=
=CwV9
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-08-30' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"The drm core grew a new generic gpu virtual address manager, and new
execution locking helpers. These are used by nouveau now to provide
uAPI support for the userspace Vulkan driver. AMD had a bunch of new
IP core support, loads of refactoring around fbdev, but mostly just
the usual amount of stuff across the board.
core:
- fix gfp flags in drmm_kmalloc
gpuva:
- add new generic GPU VA manager (for nouveau initially)
syncobj:
- add new DRM_IOCTL_SYNCOBJ_EVENTFD ioctl
dma-buf:
- acquire resv lock for mmap() in exporters
- support dma-buf self import automatically
- docs fixes
backlight:
- fix fbdev interactions
atomic:
- improve logging
prime:
- remove struct gem_prim_mmap plus driver updates
gem:
- drm_exec: add locking over multiple GEM objects
- fix lockdep checking
fbdev:
- make fbdev userspace interfaces optional
- use linux device instead of fbdev device
- use deferred i/o helper macros in various drivers
- Make FB core selectable without drivers
- Remove obsolete flags FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT
- Add helper macros and Kconfig tokens for DMA-allocated framebuffer
ttm:
- support init_on_free
- swapout fixes
panel:
- panel-edp: Support AUO B116XAB01.4
- Support Visionox R66451 plus DT bindings
- ld9040:
- Backlight support
- magic improved
- Kconfig fix
- Convert to of_device_get_match_data()
- Fix Kconfig dependencies
- simple:
- Set bpc value to fix warning
- Set connector type for AUO T215HVN01
- Support Innolux G156HCE-L01 plus DT bindings
- ili9881: Support TDO TL050HDV35 LCD panel plus DT bindings
- startek: Support KD070FHFID015 MIPI-DSI panel plus DT bindings
- sitronix-st7789v:
- Support Inanbo T28CP45TN89 plus DT bindings
- Support EDT ET028013DMA plus DT bindings
- Various cleanups
- edp: Add timings for N140HCA-EAC
- Allow panels and touchscreens to power sequence together
- Fix Innolux G156HCE-L01 LVDS clock
bridge:
- debugfs for chains support
- dw-hdmi:
- Improve support for YUV420 bus format
- CEC suspend/resume
- update EDID on HDMI detect
- dw-mipi-dsi: Fix enable/disable of DSI controller
- lt9611uxc: Use MODULE_FIRMWARE()
- ps8640: Remove broken EDID code
- samsung-dsim: Fix command transfer
- tc358764:
- Handle HS/VS polarity
- Use BIT() macro
- Various cleanups
- adv7511: Fix low refresh rate
- anx7625:
- Switch to macros instead of hardcoded values
- locking fixes
- tc358767: fix hardware delays
- sitronix-st7789v:
- Support panel orientation
- Support rotation property
- Add support for Jasonic JT240MHQS-HWT-EK-E3 plus DT bindings
amdgpu:
- SDMA 6.1.0 support
- HDP 6.1 support
- SMUIO 14.0 support
- PSP 14.0 support
- IH 6.1 support
- Lots of checkpatch cleanups
- GFX 9.4.3 updates
- Add USB PD and IFWI flashing documentation
- GPUVM updates
- RAS fixes
- DRR fixes
- FAMS fixes
- Virtual display fixes
- Soft IH fixes
- SMU13 fixes
- Rework PSP firmware loading for other IPs
- Kernel doc fixes
- DCN 3.0.1 fixes
- LTTPR fixes
- DP MST fixes
- DCN 3.1.6 fixes
- SMU 13.x fixes
- PSP 13.x fixes
- SubVP fixes
- GC 9.4.3 fixes
- Display bandwidth calculation fixes
- VCN4 secure submission fixes
- Allow building DC on RISC-V
- Add visible FB info to bo_print_info
- HBR3 fixes
- GFX9 MCBP fix
- GMC10 vmhub index fix
- GMC11 vmhub index fix
- Create a new doorbell manager
- SR-IOV fixes
- initial freesync panel replay support
- revert zpos properly until igt regression is fixeed
- use TTM to manage doorbell BAR
- Expose both current and average power via hwmon if supported
amdkfd:
- Cleanup CRIU dma-buf handling
- Use KIQ to unmap HIQ
- GFX 9.4.3 debugger updates
- GFX 9.4.2 debugger fixes
- Enable cooperative groups fof gfx11
- SVM fixes
- Convert older APUs to use dGPU path like newer APUs
- Drop IOMMUv2 path as it is no longer used
- TBA fix for aldebaran
i915:
- ICL+ DSI modeset sequence
- HDCP improvements
- MTL display fixes and cleanups
- HSW/BDW PSR1 restored
- Init DDI ports in VBT order
- General display refactors
- Start using plane scale factor for relative data rate
- Use shmem for dpt objects
- Expose RPS thresholds in sysfs
- Apply GuC SLPC min frequency softlimit correctly
- Extend Wa_14015795083 to TGL, RKL, DG1 and ADL
- Fix a VMA UAF for multi-gt platform
- Do not use stolen on MTL due to HW bug
- Check HuC and GuC version compatibility on MTL
- avoid infinite GPU waits due to premature release of request memory
- Fixes and updates for GSC memory allocation
- Display SDVO fixes
- Take stolen handling out of FBC code
- Make i915_coherent_map_type GT-centric
- Simplify shmem_create_from_object map_type
msm:
- SM6125 MDSS support
- DPU: SM6125 DPU support
- DSI: runtime PM support, burst mode support
- DSI PHY: SM6125 support in 14nm DSI PHY driver
- GPU: prepare for a7xx
- fix a690 firmware
- disable relocs on a6xx and newer
radeon:
- Lots of checkpatch cleanups
ast:
- improve device-model detection
- Represent BMV as virtual connector
- Report DP connection status
nouveau:
- add new exec/bind interface to support Vulkan
- document some getparam ioctls
- improve VRAM detection
- various fixes/cleanups
- workraound DPCD issues
ivpu:
- MMU updates
- debugfs support
- Support vpu4
virtio:
- add sync object support
atmel-hlcdc:
- Support inverted pixclock polarity
etnaviv:
- runtime PM cleanups
- hang handling fixes
exynos:
- use fbdev DMA helpers
- fix possible NULL ptr dereference
komeda:
- always attach encoder
omapdrm:
- use fbdev DMA helpers
ingenic:
- kconfig regmap fixes
loongson:
- support display controller
mediatek:
- Small mtk-dpi cleanups
- DisplayPort: support eDP and aux-bus
- Fix coverity issues
- Fix potential memory leak if vmap() fail
mgag200:
- minor fixes
mxsfb:
- support disabling overlay planes
panfrost:
- fix sync in IRQ handling
ssd130x:
- Support per-controller default resolution plus DT bindings
- Reduce memory-allocation overhead
- Improve intermediate buffer size computation
- Fix allocation of temporary buffers
- Fix pitch computation
- Fix shadow plane allocation
tegra:
- use fbdev DMA helpers
- Convert to devm_platform_ioremap_resource()
- support bridge/connector
- enable PM
tidss:
- Support TI AM625 plus DT bindings
- Implement new connector model plus driver updates
vkms:
- improve write back support
- docs fixes
- support gamma LUT
zynqmp-dpsub:
- misc fixes"
* tag 'drm-next-2023-08-30' of git://anongit.freedesktop.org/drm/drm: (1327 commits)
drm/gpuva_mgr: remove unused prev pointer in __drm_gpuva_sm_map()
drm/tests/drm_kunit_helpers: Place correct function name in the comment header
drm/nouveau: uapi: don't pass NO_PREFETCH flag implicitly
drm/nouveau: uvmm: fix unset region pointer on remap
drm/nouveau: sched: avoid job races between entities
drm/i915: Fix HPD polling, reenabling the output poll work as needed
drm: Add an HPD poll helper to reschedule the poll work
drm/i915: Fix TLB-Invalidation seqno store
drm/ttm/tests: Fix type conversion in ttm_pool_test
drm/msm/a6xx: Bail out early if setting GPU OOB fails
drm/msm/a6xx: Move LLC accessors to the common header
drm/msm/a6xx: Introduce a6xx_llc_read
drm/ttm/tests: Require MMU when testing
drm/panel: simple: Fix Innolux G156HCE-L01 LVDS clock
Revert "Revert "drm/amdgpu/display: change pipe policy for DCN 2.0""
drm/amdgpu: Add memory vendor information
drm/amd: flush any delayed gfxoff on suspend entry
drm/amdgpu: skip fence GFX interrupts disable/enable for S0ix
drm/amdgpu: Remove gfxoff check in GFX v9.4.3
drm/amd/pm: Update pci link speed for smu v13.0.6
...
Extract the internal code inside a helper function, fix the
initialization of the parameters used in the helper function
(`hidpp->answer_available` was not reset and `*response` wasn't either),
and use a `do {...} while();` loop.
Fixes: 586e8fede7 ("HID: logitech-hidpp: Retry commands when device is busy")
Cc: stable@vger.kernel.org
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230621-logitech-fixes-v2-1-3635f7f9c8af@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Use hid_device for devm allocation of the input_dev name to avoid a
use-after-free. input_unregister_device would trigger devres cleanup of all
resources associated with the input_dev, free-ing the name. The name would
subsequently be used in a uevent fired at the end of unregistering the
input_dev.
Reported-by: Maxime Ripard <mripard@kernel.org>
Closes: https://lore.kernel.org/linux-input/ZOZIZCND+L0P1wJc@penguin/T/#m443f3dce92520f74b6cf6ffa8653f9c92643d4ae
Fixes: 09308562d4 ("HID: nvidia-shield: Initial driver implementation with Thunderstrike support")
Suggested-by: Maxime Ripard <mripard@kernel.org>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230824061308.222021-4-sergeantsagara@protonmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Reference the HID device rather than the input device for the devm
allocation of the input_dev name. Referencing the input_dev would lead to a
use-after-free when the input_dev was unregistered and subsequently fires a
uevent that depends on the name. At the point of firing the uevent, the
name would be freed by devres management.
Use devm_kasprintf to simplify the logic for allocating memory and
formatting the input_dev name string.
Reported-by: Maxime Ripard <mripard@kernel.org>
Closes: https://lore.kernel.org/linux-input/ZOZIZCND+L0P1wJc@penguin/T/#m443f3dce92520f74b6cf6ffa8653f9c92643d4ae
Fixes: c08d46aa80 ("HID: multitouch: devm conversion")
Suggested-by: Maxime Ripard <mripard@kernel.org>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rahul Rameshbabu <sergeantsagara@protonmail.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230824061308.222021-3-sergeantsagara@protonmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Presently, if a call to logi_dj_recv_send_report() fails, we do
not learn about the error until after sending short
HID_OUTPUT_REPORT with hid_hw_raw_request().
To handle this somewhat unlikely issue, return on error in
logi_dj_recv_send_report() (minding ugly sleep workaround) and
take into account the result of hid_hw_raw_request().
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 6a9ddc8978 ("HID: logitech-dj: enable notifications on connect/disconnect")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230613101635.77820-1-n.zhandarovich@fintech.ru
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The ili9882t is a TDDI IC (Touch with Display Driver). The
datasheet specifies there should be 60ms between touch SDA
sleep and panel RESX. Doug's series[1] allows panels and
touchscreens to power on/off together, so we can add the 65 ms
delay in i2c_hid_core_suspend before panel_unprepare.
Because ili9882t touchscrgeen is a panel follower, and
needs to use vccio-supply instead of vcc33-supply, so set
it NULL to ili9882t_chip_data, then not use vcc33 regulator.
[1]: https://lore.kernel.org/all/20230727171750.633410-1-dianders@chromium.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20230802071947.1683318-3-yangcong5@huaqin.corp-partner.google.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Powzan keyboards KB750 and KB770 identify as
"Hailuck Co.,Ltd USB Keyboard". Adding "Hailuck" to the list
of non-apple keyboards fixes function keys for these models.
Signed-off-by: Nils Tonnaett <ntonnatt@ccrma.stanford.edu>
Reviewed-by: Rahul Rameshbabu <sergeantsagara@protonmail.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
arctis_1_battery_request[] is not used outside of this module, and as
such should be static.
Fixes: a0c76896c3 ("HID: steelseries: Add support for Arctis 1 XBox")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Logitech MX Anywhere 3 connected over Bluetooth to the device table
to get hidpi scroll supported. USB connection over the Unifying receiver
is already supported by the wildcard entry LDJ_DEVICE(HID_ANY_ID).
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Help differentiate the two remote related "serial" struct variables by
renaming "wacom_remote_data" to "wacom_remote_work_data".
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'connected' variable was poorly named, and this has led to some
confusion. We can get the same information by checking if a serial number
exists in the specified EKR slot.
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the EKR battery remains even after we stop getting information
from the device. This can lead to a stale battery persisting indefinitely
in userspace.
The remote sends a heartbeat every 10 seconds. Delete the battery if we
miss two heartbeats (after 21 seconds). Restore the battery once we see
a heartbeat again.
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 9f1015d45f ("HID: wacom: EKR: attach the power_supply on first connection")
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously would let led_classdev handle renaming when name collision
occurred. Now that an ID allocator is used to uniquely identify multiple
Thunderstrike controllers, generate unique led device names.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use power supply API to expose battery information about connected
Thunderstrike controllers to the system. Provide information on battery
capacity, charge status, charger type, voltage, and temperature.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Avoid calling thunderstrike_led_set_brightness from thunderstrike_create
when led_classdev_unregister is called. led_classdev_unregister was called
from thunderstrike_create in the error path. Calling
thunderstrike_led_set_brightness in this situation is unsafe.
Fixes: f88af60e74 ("HID: nvidia-shield: Support LED functionality for Thunderstrike")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a hid-google-stadiaff module to support rumble based force feedback
on the Google Stadia controller. This works using the HID output
endpoint exposed on both the USB and BLE interface.
Signed-off-by: Fabio Baltieri <fabiobaltieri@chromium.org>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The lightspeed receiver for the Pro X Superlight uses 13 byte mouse reports
without a report id. The workaround for such cases has been adjusted to
handle these larger packets.
The device now reports the status of its battery in wireless mode and
libratbag now recognizes the device and it can be configured with Piper.
https://github.com/libratbag/libratbag/pull/1122
Co-developed-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Mavroudis Chatzilazaridis <mavchatz@protonmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the Pro X Superlight over wired USB.
The device now reports the status of its battery.
Co-developed-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Filipe Laíns <lains@riseup.net>
Signed-off-by: Mavroudis Chatzilazaridis <mavchatz@protonmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the Steelseries Arctis 1 XBox headset. This driver
will export the battery information from the headset, as well as the
"wireless_status" property.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When connecting the Trackpad 1 via any bluetooth adapter, the device
disconnects whenever the battery level is queried. It reconnects
again after a few seconds, but it's an incredibly jarring experience
since it will just cut out in the middle of mouse operations.
This patch ignores querying the battery and avoids disconnects.
This bug is reported here:
- https://bugzilla.kernel.org/show_bug.cgi?id=204589
- https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1834085
It looks like a similar approach (disabling battery checking)
was also suggested for the Apple Magic Mouse before a custom
driver was created:
https://bugzilla.kernel.org/show_bug.cgi?id=103631
Signed-off-by: Nimish Gåtam <nimishg@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that the driver core allows for struct class to be in read-only
memory, making all 'class' structures to be declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that the driver core allows for struct class to be in read-only
memory, making all 'class' structures to be declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: Stefan Achatz <erazor_de@users.sourceforge.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As per the upstream "hidpp" helpers commit:
"
There has been some confusion about error value 5 but feature specs that
refer to it generally use NOT_ALLOWED.
"
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: 80c3fecfcd
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some digitizers (notably XP-Pen Artist 24) do not report the Invert
usage when erasing. This causes the device to be permanently stuck with
the BTN_TOOL_RUBBER tool after sending Eraser, as Invert is the only
usage that can release the tool. In this state, Touch and Inrange are
no longer reported to userspace, rendering the pen unusable.
Prior to commit 87562fcd13 ("HID: input: remove the need for
HID_QUIRK_INVERT"), BTN_TOOL_RUBBER was never set and Eraser events were
simply translated into BTN_TOUCH without causing an inconsistent state.
Introduce HID_QUIRK_NOINVERT for such digitizers and detect them during
hidinput_configure_usage(). This quirk causes the tool to be released
as soon as Eraser is reported as not set. Set BTN_TOOL_RUBBER in
input->keybit when mapping Eraser.
Fixes: 87562fcd13 ("HID: input: remove the need for HID_QUIRK_INVERT")
Co-developed-by: Nils Fuhler <nils@nilsfuhler.de>
Signed-off-by: Nils Fuhler <nils@nilsfuhler.de>
Signed-off-by: Illia Ostapyshyn <ostapyshyn@sra.uni-hannover.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch removes the error checking for debugfs_create_file
in hid-wiimote-debug.c.c. This is because the debugfs_create_file()
does not return NULL but an ERR_PTR after an error.
The DebugFS kernel API is developed in a way that the
caller can safely ignore the errors that occur during
the creation of DebugFS nodes.The debugfs Api handles
it gracefully. The check is unnecessary.
Link to the comment above debugfs_create_file:
https://elixir.bootlin.com/linux/latest/source/fs/debugfs/inode.c#L451
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Reviewed-by: David Rheinsberg <david@readahead.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Lenovo Yoga C630 has a combined keyboard and accelerometer that
interfaces via i2c-hid. Currently this laptop either has a working
keyboard (if CONFIG_HID_SENSOR_HUB is disabled) or a working accelerometer.
only works on kernels. Put another way, most distro kernels enable
CONFIG_HID_SENSOR_HUB and therefore cannot work on this device since the
keyboard doesn't work!
Fix this by providing a richer connect mask during the probe. With this
change both keyboard and screen orientation sensors work correctly.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
