This fixes the tx timeout issue seen while running a stress test on
btnxpuart for couple of hours, such that the interval between two HCI
commands coincide with the power save timeout value of 2 seconds.
Test procedure using bash script:
<load btnxpuart.ko>
hciconfig hci0 up
//Enable Power Save feature
hcitool -i hci0 cmd 3f 23 02 00 00
while (true)
do
hciconfig hci0 leadv
sleep 2
hciconfig hci0 noleadv
sleep 2
done
Error log, after adding few more debug prints:
Bluetooth: btnxpuart_queue_skb(): 01 0A 20 01 00
Bluetooth: hci0: Set UART break: on, status=0
Bluetooth: hci0: btnxpuart_tx_wakeup() tx_work scheduled
Bluetooth: hci0: btnxpuart_tx_work() dequeue: 01 0A 20 01 00
Can't set advertise mode on hci0: Connection timed out (110)
Bluetooth: hci0: command 0x200a tx timeout
When the power save mechanism turns on UART break, and btnxpuart_tx_work()
is scheduled simultaneously, psdata->ps_state is read as PS_STATE_AWAKE,
which prevents the psdata->work from being scheduled, which is responsible
to turn OFF UART break.
This issue is fixed by adding a ps_lock mutex around UART break on/off as
well as around ps_state read/write.
btnxpuart_tx_wakeup() will now read updated ps_state value. If ps_state is
PS_STATE_SLEEP, it will first schedule psdata->work, and then it will
reschedule itself once UART break has been turned off and ps_state is
PS_STATE_AWAKE.
Tested above script for 50,000 iterations and TX timeout error was not
observed anymore.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific command
to trigger firmware coredump, but the command does not have any event as
its sync response, so it is not suitable to use __hci_cmd_sync(), fixed by
using __hci_cmd_send().
Fixes: 06d3fdfcdf ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.
Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.
When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom BCM4377 driver has so far been
setting this flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag, which can simply be replaced
with HCI_QUIRK_USE_BDADDR_PROPERTY to indicate that the default address
is invalid but can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Reported-by: Felix Zhang <mrman@mrman314.tech>
Link: https://lore.kernel.org/r/77419ffacc5b4875e920e038332575a2a5bff29f.camel@mrman314.tech/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Felix Zhang <mrman@mrman314.tech>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
receive_buf() is called from ttyport_receive_buf() that expects values
">= 0" from serdev_controller_receive_buf(), change its return type from
ssize_t to size_t.
The need for this clean-up was noticed while fixing a warning, see
commit 94d0539425 ("Bluetooth: btnxpuart: fix recv_buf() return value").
Changing the callback prototype to return an unsigned seems the best way
to document the API and ensure that is properly used.
GNSS drivers implementation of serdev receive_buf() callback return
directly the return value of gnss_insert_raw(). gnss_insert_raw()
returns a signed int, however this is not an issue since the value
returned is always positive, because of the kfifo_in() implementation.
gnss_insert_raw() could be changed to return also an unsigned, however
this is not implemented here as request by the GNSS maintainer Johan
Hovold.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com> # for platform/surface
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240122180551.34429-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty core
and drivers in here, along with the usual set of rs485 updates (someday
this might work properly...) Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeUaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyOgCgp1uhP/b9iW6qM7qL6OYEG6idI0kAnj0VASNm
vSI69HmdKKwo69YLOSBp
=14n1
-----END PGP SIGNATURE-----
Merge tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove useless assignment of rx_skb to NULL in case the skb is in error,
this is already done in h4_recv_buf() that is executed a few lines
before.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return negative number in case of issue, just print an error and
return count. This fixes a WARN in ttyport_receive_buf().
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return a negative number in case of issue, just print an error
and return count. Before this change, in case of error, the returned
negative number was internally converted to 0 in ttyport_receive_buf,
now when the receive buffer is corrupted we return the size of the whole
received data (`count`). This should allow for better recovery in case
receiver/transmitter get out of sync if some data is lost.
This fixes a WARN in ttyport_receive_buf().
Bluetooth: hci0: Frame reassembly failed (-84)
------------[ cut here ]------------
serial serial0: receive_buf returns -84 (count = 6)
WARNING: CPU: 0 PID: 37 at drivers/tty/serdev/serdev-ttyport.c:37 ttyport_receive_buf+0xd8/0xf8
Modules linked in: mwifiex_sdio(+) ...
CPU: 0 PID: 37 Comm: kworker/u4:2 Not tainted 6.7.0-rc2-00147-gf1a09972a45a #1
Hardware name: Toradex Verdin AM62 WB on Verdin Development Board (DT)
Workqueue: events_unbound flush_to_ldisc
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ttyport_receive_buf+0xd8/0xf8
lr : ttyport_receive_buf+0xd8/0xf8
...
Call trace:
ttyport_receive_buf+0xd8/0xf8
flush_to_ldisc+0xbc/0x1a4
process_scheduled_works+0x16c/0x28c
Closes: https://lore.kernel.org/all/ZWEIhcUXfutb5SY6@francesco-nb.int.toradex.com/
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For QCA2066 HFP offload, HCI_Configure_Data_Path is not required since
present HCI_Enhanced_Setup_Synchronous_Connection is enough to configure
non-HCI data transport path when set both Input_Data_Path and
Output_Data_Path parameters as 0x01, as is implemented by this change.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Intel Read Version event contains a TLV(0x32) having firmware sha1 in
operational image.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This checks if there are connections before suspending since that may
disrupt the connections making it stop receiving any data if remote
wakeup is not enabled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks
for QCA2066.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Switch character types to u8 and sizes to size_t. To conform to
characters/sizes in the rest of the tty layer.
This patch converts struct serdev_device_ops hooks and its
instantiations.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20231206073712.17776-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BTMTKSDIO_BT_WAKE_ENABLED flag is set for bluetooth interrupt
during system suspend and increases wakeup count for bluetooth event.
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds support for QCA2066 firmware patch and NVM downloading.
as the RF performance of QCA2066 SOC chip from different foundries may
vary. Therefore we use different NVM to configure them based on board ID.
Changes in v2
- optimize the function qca_generate_hsp_nvm_name
- remove redundant debug code for function qca_read_fw_board_id
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If CONFIG_DEV_COREDUMP was not set, it would return -EOPNOTSUPP for
hci_devcd_register().
In this commit, ignore error return for hci_devcd_register().
Otherwise Bluetooth initialization will be failed.
Fixes: 044014ce85 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Cc: stable@vger.kernel.org
Reported-by: Kirill A. Shutemov <kirill@shutemov.name>
Closes: https://lore.kernel.org/all/ZRyqIn0_qqEFBPdy@debian.me/T/
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When the vhci device is opened in the two-step way, i.e.: open device
then write a vendor packet with requested controller type, the device
shall respond with a vendor packet which includes HCI index of created
interface.
When the virtual HCI is created, the host sends a reset request to the
controller. This request is processed by the vhci_send_frame() function.
However, this request is send by a different thread, so it might happen
that this HCI request will be received before the vendor response is
queued in the read queue. This results in the HCI vendor response and
HCI reset request inversion in the read queue which leads to improper
behavior of btvirt:
> dmesg
[1754256.640122] Bluetooth: MGMT ver 1.22
[1754263.023806] Bluetooth: MGMT ver 1.22
[1754265.043775] Bluetooth: hci1: Opcode 0x c03 failed: -110
In order to synchronize vhci two-step open/setup process with virtual
HCI initialization, this patch adds internal lock when queuing data in
the vhci_send_frame() function.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We should send hci reset command before bt turn off, which can reset bt
firmware status.
Signed-off-by: Rocky Liao <quic_rjliao@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
It is not allowed to call kfree_skb() from hardware interrupt
context or with hardware interrupts being disabled.
So replace kfree_skb() with dev_kfree_skb_irq() under
spin_lock_irqsave(). Compile tested only.
Fixes: baac6276c0 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The quirks table was named "blacklist_table" which isn't a good
description for that table as devices detected using it weren't ignored
by the driver.
Rename the table to match what it actually does.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the WCN7850 Bluetooth chipset.
Tested on the SM8550 QRD platform.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use switch/case to handle soc type specific behaviour,
the permit dropping the qca_is_xxx() inline functions
and make the code clearer and easier to update for new
SoCs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This improves the inband IR command handling for NXP BT chipsets.
When the IR vendor command is received, the driver injects a HW
error event, which causes a reset sequence in hci_error_reset().
The vendor IR command is sent to the controller while hci dev
is been closed, and FW is re-downloaded when nxp_setup() is
called during hci_dev_do_open().
The HCI_SETUP flag is set in nxp_hw_err() to make sure that
nxp_setup() is been called during hci_dev_do_open().
This also makes the nxp_setup() and power save functions more
generic.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for NXP IW624 chipset in btnxpuart driver
by adding FW name and bootloader signature. Based on the
loader version bits 7:6 of the bootloader signature, the
driver can choose between selecting secure and non-secure
FW files.
For cmd5 payload during FW download, this chip has addresses
of few registers offset by 1, so added boot_reg_offset to
handle the chip specific offset.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the unnecessary check for CTS low after FW download.
After FW download is complete, the CTS line is already seen low.
It becomes high after 2 msec, and low again after FW initialization
is complete.
This makes the current check for CTS low redundant.
This removes the wait for CTS low section and increase delay to
1200msec instead, which is sufficiant for all NXP chipsets to
initialize FW.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some hooks in struct tty_ldisc_ops still reference buffers by 'unsigned
char'. Unify to 'u8' as the rest of the tty layer does.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810091510.13006-32-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes all those 'char's an explicit 'u8'. This is part of the
continuing unification of chars and flags to be consistent u8.
This approaches tty_port_default_receive_buf().
Note that we do not change signedness as we compile with
-funsigned-char.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-18-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Count passed to tty_ldisc_ops::receive_buf*(), ::lookahead_buf(), and
returned from ::receive_buf2() is expected to be size_t. So set it to
size_t to unify with the rest of the code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_ops::poll() is optional and needs not be provided. It is equal
to returning 0. So remove all those from the code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810091510.13006-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this commit, prefer to load FW v2 if available. Fallback to FW v1
otherwise. This behavior is only for RTL8852C.
Fixes: 9a24ce5e29 ("Bluetooth: btrtl: Firmware format v2 support")
Cc: stable@vger.kernel.org
Suggested-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btusb_recv_event_intel is specific to Intel controllers therefore it
shall be placed inside btintel.c so btusb don't have a mix of vendor
specific code with the generic parts.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the Bluetooth chip codenamed APACHE which is part of
WCN3988.
The firmware for this chip has a slightly different naming scheme
compared to most others. For ROM Version 0x0200 we need to use
apbtfw10.tlv + apnv10.bin and for ROM version 0x201 apbtfw11.tlv +
apnv11.bin
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for NXP AW693 chipset in btnxpuart driver
by adding FW name and bootloader signature. Based on the
loader version bits 7:6 of the bootloader signature, the
driver can choose between selecting secure and non-secure
FW files.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
in nokia_bluetooth_serdev_probe(), check the return value of
clk_prepare_enable() and return the error code if
clk_prepare_enable() returns an unexpected value.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The BCM43430A1 has a default MAC address of AA:AA:AA:AA:AA:AA.
Although, unlike some other entries, this does not include the
chip name, it is clearly not a real address. This was found in
AzureWave AW-NB197SM and AW-NM372SM modules.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implement function .coredump() and dmp_hdr() in btusb
driver for MediaTek controller. FW core dump was triggered by FW
specific event to show something unexpected happened in the controller.
The driver would be responsible for collecting and uploading the device
core dump pieces in hci driver using core dump API. Once we finished
the whole process, the driver would reset the controller to recover the
kind of fatal error.
Co-developed-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Introduce btmtk_reset_work which can be called whenever the firmware abort,
HCI command timeout, other fatal error happen.
Co-developed-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use readx_poll_timeout instead of open coding to poll the hardware reset
status until it is done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add printing firmware information part when driver loading firmware that
user can get mediatek bluetooth information.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add hardware variant(0x1c) for Gale Peak core (CNVi).
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
New Intel platforms supports reset of Bluetooth device via ACPI DSM
methods. The legacy reset mechanism via GPIO will be deprecated in
future. This patch checks the platform support for reset methods and if
supported uses the same instead of legacy GPIO toggling method.
ACPI firmware supports two types of reset method based on NIC card.
(Discrete or Integrated).
1. VSEC Type - Vendor Specific Extended Capability. Here BT_EN and
BT_IF_SELECT lines are driven by a register in PCH cluster. This
interface is supported on discrete BT solution.
2. WDISABLE2 - In this soluton, W_DISABLE2 pin in M.2 is connected to
physical GPIO from PCH. The DSM interface shall toggle this to recover
from error.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Intercept debug exception events from QCA controller and put them into
a devcoredump using hci devcoredump APIs of hci_core
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
V2 -> V3:
---------
changed hci_coredump_qca function
V1 -> V2:
---------
Updated to work with the updated HCI devcoredump API.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implements the hci_qca driver side .coredump() callback to
trigger a devcoredump via sysfs.
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
v2 -> V3:
--------
Updated commit text
v1 -> V2:
--------
Updated to work with the updated HCI devcoredump API.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The original code did not determine the length value of the HCI command
for drop fw even there's no parameter needed. In this commit, use struct
hci_command_hdr to manage opcode and length. It would be more regular and
more readable.
Suggested-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Catch debug exception from controller and driver, and trigger a
devcoredump using hci devcoredump APIs. The debug exception data
will be parsed in userspace.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit c13380a555 ("Bluetooth: btusb: Do not require hardcoded
interface numbers") inadvertedly broke bluetooth on Intel Macbook 2014.
The intention was to keep behavior intact when BTUSB_IFNUM_2 is set and
otherwise allow any interface numbers. The problem is that the new logic
condition omits the case where bInterfaceNumber is 0.
Fix BTUSB_IFNUM_2 handling by allowing both interface number 0 and 2
when the flag is set.
Fixes: c13380a555 ("Bluetooth: btusb: Do not require hardcoded interface numbers")
Reported-by: John Holland <johnbholland@icloud.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217651
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Tested-by: John Holland<johnbholland@icloud.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9yzk
-----END PGP SIGNATURE-----
Merge tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and wireguard.
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind"
* tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
nfp: clean mc addresses in application firmware when closing port
selftests: mptcp: pm_nl_ctl: fix 32-bit support
selftests: mptcp: depend on SYN_COOKIES
selftests: mptcp: userspace_pm: report errors with 'remove' tests
selftests: mptcp: userspace_pm: use correct server port
selftests: mptcp: sockopt: return error if wrong mark
selftests: mptcp: sockopt: use 'iptables-legacy' if available
selftests: mptcp: connect: fail if nft supposed to work
mptcp: do not rely on implicit state check in mptcp_listen()
mptcp: ensure subflow is unhashed before cleaning the backlog
s390/qeth: Fix vipa deletion
octeontx-af: fix hardware timestamp configuration
net: dsa: sja1105: always enable the send_meta options
net: dsa: tag_sja1105: fix MAC DA patching from meta frames
net: Replace strlcpy with strscpy
pptp: Fix fib lookup calls.
mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check
net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
xsk: Honor SO_BINDTODEVICE on bind
ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported
...
For virtio-net we were getting CPU stall warnings, and fixed it by
calling the scheduler: see f8bb510439 ("virtio_net: suppress cpu stall
when free_unused_bufs").
This driver is similar so theoretically the same logic applies.
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Message-Id: <20230609131817.712867-4-xianting.tian@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Adding the device ID from the Asus Ally gets the bluetooth working
on the device.
Signed-off-by: Matthew Anderson <ruinairas1992@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom driver has so far been setting this
flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag. Use this flag to indicate
when the address can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/lkml/ecef83c8-497f-4011-607b-a63c24764867@samsung.com
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use le32_to_cpu for ver.soc_id to fix the following
sparse warning.
drivers/bluetooth/btqca.c:640:24: sparse: warning: restricted
__le32 degrades to integer
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing MODULE_FIRMWARE declarations for firmware referenced in
btrtl.c.
Signed-off-by: Dan Gora <dan.gora@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support
during hci down for wcn3990"), the setup callback which registers the
debugfs interface can be called multiple times.
This specifically leads to the following error when powering on the
controller:
debugfs: Directory 'ibs' with parent 'hci0' already present!
Add a driver flag to avoid trying to register the debugfs interface more
than once.
Fixes: 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Cc: stable@vger.kernel.org # 4.20
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the follwing compiler warning reported by kernel test robot:
drivers/bluetooth/btnxpuart.c:1332:34: warning: unused variable
'nxpuart_of_match_table' [-Wunused-const-variable]
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305161345.eClvTYQ9-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
WCN6855 will report memdump via ACL data or HCI event when
it get crashed, so we collect memdump to debug firmware.
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables flow control before checking for bootloader signature and
deciding whether FW download is needed or not. In case of V1 bootloader
chips w8987 and w8997, it is observed that if WLAN FW is downloaded first
and power save is enabled in wlan core, bootloader signatures are not
emitted by the BT core when the chip is put to sleep. As a result, the
driver skips FW download and subsequent HCI commands get timeout errors
in dmesg as shown below:
[ 112.898867] Bluetooth: hci0: Opcode 0x c03 failed: -110
[ 114.914865] Bluetooth: hci0: Setting baudrate failed (-110)
[ 116.930856] Bluetooth: hci0: Setting wake-up method failed (-110)
By enabling the flow control, the host enables its RTS pin, and an
interrupt in chip's UART peripheral causes the bootloader to wake up,
enabling the bootloader signatures, which then helps in downloading
the bluetooth FW file.
This changes all instances of 0/1 for serdev_device_set_flow_control()
to false/true.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Realtek changed the format of the firmware file as v2. The driver
should implement the patch to extract the firmware data from the
firmware file. The future chips must apply this patch for firmware loading.
This patch is compatible with the both previous format and v2 as well.
Signed-off-by: Allen Chen <allen_chen@realsil.com.cn>
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 1e9ac114c4.
This patch introduces a possible null-ptr-def problem. Revert it. And the
fixed bug by this patch have resolved by commit 73f7b171b7 ("Bluetooth:
btsdio: fix use after free bug in btsdio_remove due to race condition").
Fixes: 1e9ac114c4 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The ATS2851 based controller advertises support for command "LE Set Random
Private Address Timeout" but does not actually implement it, impeding the
controller initialization.
Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller
initialization.
< HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Status (0x0f) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1
Status: Unknown HCI Command (0x01)
Co-developed-by: imoc <wzj9912@gmail.com>
Signed-off-by: imoc <wzj9912@gmail.com>
Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There are a number of bugs here:
1) If "count" is less than sizeof(dump_data.data) then it copies
uninitialized data.
2) If simple_write_to_buffer() returns -EFAULT then we run into a
problem "ret < count" comparison. "count" is an unsigned long so the
comparison is type promoted to unsigned long and the negative returns
become high positive values. That also results in copying
uninitialized data.
3) If "*ppos" is non-zero then the first part of the dump_data
buffer is uninitialized. Using copy_from_user() instead of
simple_write_to_buffer() is more appropriate here.
Fixes: d5d5df6da0aa ("Bluetooth: Add vhci devcoredump support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We can never assume the uart will deliver a complete packet to the BT
layer at once, the expected packet may be divided into several parts by
uart as uart doesn't know the received packet size, the received data
count may mismatch with the expected packet size, so here
is_valid_bootloader_signature() check may always return false.
Even we remove the count check in is_valid_bootloader_signature(), then
the first part of the data which includes the packet type can pass the
is_valid_bootloader_signature() check, but the remaining parts don't
have the packet type data still cannot pass the check, here return
directly will cause the data loss.
So need to remove the received bootloader signature check here, the
h4_recv_buf() can help us combine the different data received into one
packet. If any out-of-sync or incomplete bootloader signature is received,
it is safe to ignore and discard it, and process the next bootloader
signature.
Co-developed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This sets the default power save mode setting to disabled.
With this setting, this driver will behave like a normal h4 driver.
If user needs to use the power save feature, it can be enabled
using the following vendor command:
hcitool cmd 3f 23 02 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a call to ps_wakeup() before closing the serdev device, to
de-assert UART break.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support to download helper FW file for the legacy NXP chipset
88w8997 for the btnxpuart driver. This helper FW file is necessary to
set the bootloader baudrate to 3000000 after which the actual BT FW file
can be downloaded. This change helps bring the FW download time from
around 10 sec to less than 2 sec for 88w8997 chip. For newer chipsets,
both V1 and V3 bootloader, driver sends the cmd5 and cmd7 to the chip
bootloader, and does not need a helper FW file.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The DSDT for the Acer Iconia One 7 B1-750 models (which share
the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but
this is not correct.
Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO
controller for the IRQ and this pin is _not_ configured in direct IRQ
mode by the firmware.
Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table,
to fix bluetooth not working on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The DSDT for the Lenovo Yoga Tablet 2 830 / 1050 models (which share
the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but
this is not correct.
Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO
controller for the IRQ and this pin is _not_ configured in direct IRQ
mode by the firmware.
Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table,
to fix bluetooth not working on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The bcm43430a0 and bcm43430a1 BT does not support the 0xfc45 command
to set the UART clock to 48 MHz and it also does not work at 4000000
baud without this command as some newer models do.
These chips are found on ACPI/x86 devices where the operating baudrate
does not come from the firmware but is hardcoded at 4000000, which does
not work.
Add a max_baudrate value to struct bcm_device_data and set this
to 2000000 on all known ACPI hardware-ids for the bcm43430a0
and the bcm43430a1.
Note this also adds the BCM2E9F ACPI HID which was missing until now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On some devices the BCM Bluetooth adapter does not have a valid bdaddr set.
btbcm.c currently sets HCI_QUIRK_INVALID_BDADDR to indicate when this is
the case. But this requires users to manual setup a btaddr, by doing e.g.:
btmgmt -i hci0 public-addr 'B0:F1:EC:82:1D:B3'
Which means that Bluetooth will not work out of the box on such devices.
To avoid this (where possible) hci_bcm sets: HCI_QUIRK_USE_BDADDR_PROPERTY
which tries to get the bdaddr from devicetree.
But this only works on devicetree platforms. On UEFI based platforms
there is a special Broadcom UEFI variable which when present contains
the devices bdaddr, just like how there is another UEFI variable which
contains wifi nvram contents including the wifi MAC address.
Add support for getting the bdaddr from this Broadcom UEFI variable,
so that Bluetooth will work OOTB for users on devices where this
UEFI variable is present.
This fixes Bluetooth not working on for example Asus T100HA 2-in-1s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
As shown in the schematic diagram below.There may be a critical
scenario in the current code. If the device does not receive an
pure ack sent by the host due to insufficient receive buffer or
other reasons and triggers a retransmission, the host will always
be in an 'out-of-order' state.The state machine will get stuck.
host device
SEQ3,ACK4 --------->
<--------- SEQ4,ACK4
pure ACK ---------> (not received)
(out-of-order) <--------- SEQ4,ACK4(retransmission)
........
(out-of-order) <--------- SEQ4,ACK4(retransmission)
According to the description in the core specification: "whenever
a reliable packet is received, an acknowledgment shall be generated."
So set H5_TX_ACK_REQ bit to trigger retransmission of pure ack packet
when "out-of-order" occurs.
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Intercept debug exception events from the controller and put them into
a devcoredump using hci devcoredump APIs. The debug exception contains
data in a TLV format and it will be parsed in userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implements the btusb driver side .coredump() callback to
trigger a devcoredump via sysfs.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add devcoredump support for vhci that creates forcce_devcoredump debugfs
entry. This is used for mgmt-tester tests.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Basically all Intel controllers support both Central/Peripheral
LE states.
This patch enables the LE States quirk by default on all
Solar and Magnertor Intel controllers.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add regulators, GPIOs and changes required to power on/off wcn6855.
Add support for firmware download for wcn6855 which is in the
linux-firmware repository as hpbtfw21.tlv and hpnv21.bin.
Based on the assumption that this is similar to the wcn6750
Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The btrtl_set_quirks() has accessed btrtl_dev->ic_info->lmp_subver since
b8e482d02513. However, if installing a Realtek Bluetooth controller
without the driver supported, it will hit the NULL point accessed.
Add a check for NULL to avoid the Kernel Oops.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver needs both CRC32 and CRC8 to link correctly:
ld: drivers/bluetooth/btnxpuart.o: in function `nxp_serdev_probe':
drivers/bluetooth/btnxpuart.c:1214: undefined reference to
`crc8_populate_msb'
ld: drivers/bluetooth/btnxpuart.o: in function `nxp_send_ack':
drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'
ld: drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'
Fixes: 3e662aa4453a ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a driver based on serdev driver for the NXP BT serial protocol
based on running H:4, which can enable the built-in Bluetooth device
inside an NXP BT chip.
This driver has Power Save feature that will put the chip into sleep state
whenever there is no activity for 2000ms, and will be woken up when any
activity is to be initiated over UART.
This driver enables the power save feature by default by sending the vendor
specific commands to the chip during setup.
During setup, the driver checks if a FW is already running on the chip
by waiting for the bootloader signature, and downloads device specific FW
file into the chip over UART if bootloader signature is received..
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
tty_set_termios() never returns anything else than 0. Make the debug
prints to look directly into the new termios instead to check CRTSCTS
state.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add two more quirks to resume the device initialization and basic
operation as the device seems not to support "Read Transmit Power"
and "Set Extended Scan Parameters".
< HCI Command: LE Read Transmit Power (0x08|0x004b) plen 0
> HCI Event: Command Status (0x0f) plen 4
LE Read Transmit Power (0x08|0x004b) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Status (0x0f) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Raul Cheleguini <rcheleguini@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth
module which is connected via UART to the host.
It shares lmp subversion with 8703B, so Realtek's userspace
initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS
(CG, VF, XX) with RTL8703B using vendor's command to read chip type.
Also this chip declares support for some features it doesn't support
so add a quirk to indicate that these features are broken.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/btmtkuart.c:971:36: error: ‘mt7668_data’ defined
but not used [-Werror=unused-const-variable=]
drivers/bluetooth/btmtkuart.c:966:36: error: ‘mt7663_data’ defined
but not used [-Werror=unused-const-variable=]
drivers/bluetooth/btmtkuart.c:962:36: error: ‘mt7622_data’ defined
but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’
defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/btmrvl_sdio.c:43:34: error:
‘btmrvl_sdio_of_match_table’ defined but not used
[-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/bluetooth/hci_ll.c:769:34: error: ‘hci_ti_of_match’ defined
but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
RTL8821CS is a WiFi + Bluetooth combo chip from Realtek that provides
WiFi A/B/G/N/AC over an SDIO interface and Bluetooth 4.2 over a UART
interface.
Note that the firmware this was tested with was firmware version
0x75b8f098.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the support for RTL8852BS BT controller on UART interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Victor Hassan <victor@allwinnertech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add serdev support for the 88W8997 from NXP (previously Marvell). It
includes support for changing the baud rate. The command to change the
baud rate is taken from the user manual UM11483 Rev. 9 in section 7
(Bring-up of Bluetooth interfaces) from NXP.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use the maybe_unused macro for the device tree ids instead of #ifdef
CONFIG_OF. This makes it easier to add support for new devices.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove hardcoded interface number check because Bluetooth specification
since version 4.0 only recommends and no longer requires specific
interface numbers.
While earlier Bluetooth versions, i.e. 2.1 + EDR and 3.0 + HS, contain
required configuration table in Volume 4 - Host Controller Interface
Part B - USB Transport Layer, Bluetooth Core Specification Addendum 2
changes the table from required to recommended configuration.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch fixes an incorrect loop exit condition in code that replaces
'/' symbols in the board name. There might also be a memory corruption
issue here, but it is unlikely to be a real problem.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Finkelstein <fnkl.kernel@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In btsdio_probe, the data->work is bound with btsdio_work. It will be
started in btsdio_send_frame.
If the btsdio_remove runs with a unfinished work, there may be a race
condition that hdev is freed but used in btsdio_work. Fix it by
canceling the work before do cleanup in btsdio_remove.
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In btsdio_probe, &data->work was bound with btsdio_work.In
btsdio_send_frame, it was started by schedule_work.
If we call btsdio_remove with an unfinished job, there may
be a race condition and cause UAF bug on hdev.
Fixes: ddbaf13e36 ("[Bluetooth] Add generic driver for Bluetooth SDIO devices")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On most devices using the btqcomsmd driver (e.g. the DragonBoard 410c
and other devices based on the Qualcomm MSM8916/MSM8909/... SoCs)
the Bluetooth firmware seems to become unresponsive for a while after
setting the BD address. On recent kernel versions (at least 5.17+)
this often causes timeouts for subsequent commands, e.g. the HCI reset
sent by the Bluetooth core during initialization:
Bluetooth: hci0: Opcode 0x c03 failed: -110
Unfortunately this behavior does not seem to be documented anywhere.
Experimentation suggests that the minimum necessary delay to avoid
the problem is ~150us. However, to be sure add a sleep for > 1ms
in case it is a bit longer on other firmware versions.
Older kernel versions are likely also affected, although perhaps with
slightly different errors or less probability. Side effects can easily
hide the issue in most cases, e.g. unrelated incoming interrupts that
cause the necessary delay.
Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current flow interates over entire ACPI table entries looking for
Bluetooth Per Platform Antenna Gain(PPAG) entry. This patch iterates
over ACPI entries relvant to Bluetooth device only.
Fixes: c585a92b2f ("Bluetooth: btintel: Set Per Platform Antenna Gain(PPAG)")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the code introduced by
14202eff21 as hci_recv_frame is now able
to detect ACL packets that are in fact ISO packets.
Fixes: 14202eff21 ("Bluetooth: btusb: Detect if an ACL packet is in fact an ISO packet")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Antenna gain is defined as the antenna’s ability to
increase the Tx power in a given direction. Intel
is certifying its products with fixed reference
antenna peak gain values (3/5dBi). The feature takes
into account the actual antenna gain, and increases
output power values, which results in a performance
improvement.
After firmware download is completed, driver reads from
ACPI table and configures PPAG as required. ACPI table
entry for PPAG is defined as below.
Name (PPAG, Package (0x02)
{
0x00000001,
Package (0x02)
{
0x00000012, /* Bluetooth Domain */
0x00000001 /* 1 - Enable PPAG, 0 - Disable PPAG */
}
})
btmon log:
< HCI Command: Intel Configure Per Platform Antenna Gain (0x3f|0x0219) plen 12
Mcc: 0x00000000
Selector: Enable
Delta: 0x00000000
> HCI Event: Command Complete (0x0e) plen 4
Intel Configure Per Platform Antenna Gain (0x3f|0x0219) ncmd 1
Status: Success (0x00)
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Seema Sreemantha <seema.sreemantha@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth controller attached via the UART is handled by the serdev driver.
Get the wakeup status from the device handle through serdev, instead of the
parent path.
Fixes: c1a74160ea ("Bluetooth: hci_qca: Add device_may_wakeup support")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following warnings:
drivers/bluetooth/hci_qca.c:1014:26: warning: cast to restricted __le16
drivers/bluetooth/hci_qca.c:1028:37: warning: cast to restricted __le32
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver shutdown callback (which sends EDL_SOC_RESET to the device
over serdev) should not be invoked when HCI device is not open (e.g. if
hci_dev_open_sync() failed), because the serdev and its TTY are not open
either. Also skip this step if device is powered off
(qca_power_shutdown()).
The shutdown callback causes use-after-free during system reboot with
Qualcomm Atheros Bluetooth:
Unable to handle kernel paging request at virtual address
0072662f67726fd7
...
CPU: 6 PID: 1 Comm: systemd-shutdow Tainted: G W
6.1.0-rt5-00325-g8a5f56bcfcca #8
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
tty_driver_flush_buffer+0x4/0x30
serdev_device_write_flush+0x24/0x34
qca_serdev_shutdown+0x80/0x130 [hci_uart]
device_shutdown+0x15c/0x260
kernel_restart+0x48/0xac
KASAN report:
BUG: KASAN: use-after-free in tty_driver_flush_buffer+0x1c/0x50
Read of size 8 at addr ffff16270c2e0018 by task systemd-shutdow/1
CPU: 7 PID: 1 Comm: systemd-shutdow Not tainted
6.1.0-next-20221220-00014-gb85aaf97fb01-dirty #28
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xdc/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x68/0x84
print_report+0x188/0x488
kasan_report+0xa4/0xf0
__asan_load8+0x80/0xac
tty_driver_flush_buffer+0x1c/0x50
ttyport_write_flush+0x34/0x44
serdev_device_write_flush+0x48/0x60
qca_serdev_shutdown+0x124/0x274
device_shutdown+0x1e8/0x350
kernel_restart+0x48/0xb0
__do_sys_reboot+0x244/0x2d0
__arm64_sys_reboot+0x54/0x70
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x44/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xbc/0x140
el0t_64_sync+0x190/0x194
Fixes: 7e7bbddd02 ("Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 43eb12d789 ("Bluetooth: Fix/implement Three-wire reliable packet sending")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 166d2f6a43 ("[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chips")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 0ff252c197 ("Bluetooth: hciuart: Add support QCA chipset for UART")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 803b58367f ("Bluetooth: btusb: Implement driver internal packet reassembly")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
skb allocated by __hci_cmd_sync would not be used whether in checking
for supported iBT hardware variants or after, we should free it in all
error branches, this patch makes the case read version failed or default
error case free skb before return.
Fixes: c86c7285bb ("Bluetooth: btintel: Fix the legacy bootloader returns tlv based version")
Fixes: 019a1caa7f ("Bluetooth: btintel: Refactoring setup routine for bootloader devices")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btintel.c:1041:38: warning: cast to restricted __le32
drivers/bluetooth/btintel.c:1786:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1795:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1796:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1797:25: warning: cast to restricted __le16
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btusb.c:3426:28: warning: cast to restricted __le32
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2245:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2249:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2253:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2257:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2261:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2267:18: warning: cast to restricted __le16
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
after probe() failure.
Fixes: ab80b2cec05f ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom BCM4377/4378/4387 are dual WiFi/Bluetooth boards found in Apple
machines. This driver adds support for the Bluetooth function which
exposes a shared memory IPC protocol over PCIe to tunnel HCI traffic.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress.
This chip is present e.g. on muRata 2AE module.
This chip has additional quirk where the HCI command 0xfc45, used on
older chips to switch UART clock from 24 MHz to 48 MHz, to support
baudrates over 3 Mbdps, is no longer recognized by this newer chip.
This newer chip can configure the 4 Mbdps baudrate without the need
to issue HCI command 0xfc45, so add flag to indicate this and do not
issue the command on this chip to avoid failure to set 4 Mbdps baud
rate.
It is not clear whether there is a way to determine which chip does
and which chip does not support the HCI command 0xfc45, other than
trial and error.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add IDs to usb_device_id table for WCN6855. IDs are extracted from Windows
driver of Lenovo Thinkpad T14 Gen 2(Driver version 1.0.0.1205 Windows 10)
Windows driver download address:
https://pcsupport.lenovo.com/us/en/products/laptops-and-netbooks/
thinkpad-t-series-laptops/thinkpad-t14-gen-2-type-20xk-20xl/downloads
/driver-list/
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
poll_sync has been proven to fix races of USB data and event endpoints
so this enables it by default.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
This adds CONFIG_BT_HCIBTUSB_POLL_SYNC which can be used to set the
default behavior of Bluetooth USB controller with respect to poll
synchronization of its endpoits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
The current version of the configuration structure has unaligned
16-bit fields, but according to the specification [1], access to
the configuration space must be aligned.
Add a second, aligned version of the configuration structure
and a new feature bit indicating that this version is being used.
[1] https://docs.oasis-open.org/virtio/virtio/v1.1/virtio-v1.1.pdf
Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Only assign hdev->wakeup if the serial port supports wakeup. Otherwise
it will fall back to the hci_uart_wakeup or the behavior that can be
overridden before calling the hci_uart_register_device().
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For USB ALT 6 settings some Realtek chips need to transmit mSBC data
continuously without the zero length of USB packets.
In this commit, create BTUSB_ALT6_CONTINUOUS_TX to manage the behavior.
Therefore, create REALTEK_ALT6_CONTINUOUS_TX_CHIP to manage the specific
chip model for the behavior.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds a data structure for btrealtek object, and the
definition of vendor behavior flags. It also adds macros to set/test/get
the flags.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device removal is clearly out of virtio spec: it attempts to remove
unused buffers from a VQ before invoking device reset. To fix, make
open/close NOPs and do all cleanup/setup in probe/remove.
NB: This is a hacky way to handle this - virtbt_{open,close} as NOP is
not really what a driver is supposed to be doing. These are transport
enable/disable callbacks from the BT core towards the driver. It maps to
a device being enabled/disabled by something like bluetoothd for
example. So if disabled, users expect that no resources/queues are in
use. It does work with all other transports like USB, SDIO, UART etc.
There should be no buffer used if the device is powered off. We also
don’t have any USB URBs in-flight if the transport is not active.
The way to implement a proper fix would be using vq reset if supported,
or even using a full device reset.
The cost of the hack is a single skb wasted on an unused bt device.
NB2: with this fix in place driver still suffers from a race condition
if an interrupt triggers while device is being reset. To fix, in the
virtbt_close() callback we should deactivate all interrupts. To be
fixed.
squashed fixup: bluetooth: virtio_bt: fix an error code in probe()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220811080943.198245-1-mst@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
The USB interface between the host and the bluetooth adapter used for
SCO packets uses an USB isochronous endpoint with a fragmentation scheme
that does not tolerate errors. Except USB isochronous transfers do
not provide a reliable stream with guaranteed delivery. (There is no
retry on error, see USB spec v2.0 5.6 and 8.5.5.)
To fragment a packet, the bluetooth HCI simply splits it in parts and
transfer them as-is. The receiver is expected to reconstruct the packet
by assuming the first fragment contains the header and parsing its size
field. There is no error detection either.
If a fragment is lost, the end result is that the kernel is no longer
synchronized and will pass malformed data to the upper layers, since it
has no way to tell if the first fragment is an actual first fragment or
a continuation fragment. Resynchronization can only happen by luck and
requires an unbounded amount of time.
The typical symptom for a HSP/HFP bluetooth headset is that the
microphone stops working and dmesg contains piles of rate-limited
"Bluetooth: hci0: SCO packet for unknown connection handle XXXX"
errors for an indeterminate amount of time, until the kernel accidentally
resynchronize.
A workaround is to ask the upper layer to prevalidate the first fragment
header. This is not possible with user channels so this workaround is
disabled in this case.
This problem is the most severe when using an ath3k adapter on an i.MX 6
board, where packet loss occur regularly, possibly because it is an USB1
device connected on an USB2 hub and this is a special case requiring
split transactions.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On cmd_timeout with no reset_gpio, reset the USB port as a last
resort.
This patch changes the behavior of btusb_intel_cmd_timeout and
btusb_rtl_cmd_timeout.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In case of suspend/resume and HCI_RESET (BT On and Off),
ISOC endpoint set to alt setting 0 when no SCO connection exists.
This patch shall avoid resetting of ISOC endpoint to alt setting to 0.
Signed-off-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
- Core:
- The timer_shutdown[_sync]() infrastructure:
Tearing down timers can be tedious when there are circular
dependencies to other things which need to be torn down. A prime
example is timer and workqueue where the timer schedules work and the
work arms the timer.
What needs to prevented is that pending work which is drained via
destroy_workqueue() does not rearm the previously shutdown
timer. Nothing in that shutdown sequence relies on the timer being
functional.
The conclusion was that the semantics of timer_shutdown_sync() should
be:
- timer is not enqueued
- timer callback is not running
- timer cannot be rearmed
Preventing the rearming of shutdown timers is done by discarding rearm
attempts silently. A warning for the case that a rearm attempt of a
shutdown timer is detected would not be really helpful because it's
entirely unclear how it should be acted upon. The only way to address
such a case is to add 'if (in_shutdown)' conditionals all over the
place. This is error prone and in most cases of teardown not required
all.
- The real fix for the bluetooth HCI teardown based on
timer_shutdown_sync().
A larger scale conversion to timer_shutdown_sync() is work in
progress.
- Consolidation of VDSO time namespace helper functions
- Small fixes for timer and timerqueue
- Drivers:
- Prevent integer overflow on the XGene-1 TVAL register which causes
an never ending interrupt storm.
- The usual set of new device tree bindings
- Small fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=JlDe
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2022-12-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for timers, timekeeping and drivers:
Core:
- The timer_shutdown[_sync]() infrastructure:
Tearing down timers can be tedious when there are circular
dependencies to other things which need to be torn down. A prime
example is timer and workqueue where the timer schedules work and
the work arms the timer.
What needs to prevented is that pending work which is drained via
destroy_workqueue() does not rearm the previously shutdown timer.
Nothing in that shutdown sequence relies on the timer being
functional.
The conclusion was that the semantics of timer_shutdown_sync()
should be:
- timer is not enqueued
- timer callback is not running
- timer cannot be rearmed
Preventing the rearming of shutdown timers is done by discarding
rearm attempts silently.
A warning for the case that a rearm attempt of a shutdown timer is
detected would not be really helpful because it's entirely unclear
how it should be acted upon. The only way to address such a case is
to add 'if (in_shutdown)' conditionals all over the place. This is
error prone and in most cases of teardown not required all.
- The real fix for the bluetooth HCI teardown based on
timer_shutdown_sync().
A larger scale conversion to timer_shutdown_sync() is work in
progress.
- Consolidation of VDSO time namespace helper functions
- Small fixes for timer and timerqueue
Drivers:
- Prevent integer overflow on the XGene-1 TVAL register which causes
an never ending interrupt storm.
- The usual set of new device tree bindings
- Small fixes and improvements all over the place"
* tag 'timers-core-2022-12-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
dt-bindings: timer: renesas,cmt: Add r8a779g0 CMT support
dt-bindings: timer: renesas,tmu: Add r8a779g0 support
clocksource/drivers/arm_arch_timer: Use kstrtobool() instead of strtobool()
clocksource/drivers/timer-ti-dm: Fix missing clk_disable_unprepare in dmtimer_systimer_init_clock()
clocksource/drivers/timer-ti-dm: Clear settings on probe and free
clocksource/drivers/timer-ti-dm: Make timer_get_irq static
clocksource/drivers/timer-ti-dm: Fix warning for omap_timer_match
clocksource/drivers/arm_arch_timer: Fix XGene-1 TVAL register math error
clocksource/drivers/timer-npcm7xx: Enable timer 1 clock before use
dt-bindings: timer: nuvoton,npcm7xx-timer: Allow specifying all clocks
dt-bindings: timer: rockchip: Add rockchip,rk3128-timer
clockevents: Repair kernel-doc for clockevent_delta2ns()
clocksource/drivers/ingenic-ost: Define pm functions properly in platform_driver struct
clocksource/drivers/sh_cmt: Access registers according to spec
vdso/timens: Refactor copy-pasted find_timens_vvar_page() helper into one copy
Bluetooth: hci_qca: Fix the teardown problem for real
timers: Update the documentation to reflect on the new timer_shutdown() API
timers: Provide timer_shutdown[_sync]()
timers: Add shutdown mechanism to the internal functions
timers: Split [try_to_]del_timer[_sync]() to prepare for shutdown mode
...
The rationale of showing this is that it's potentially critical
information to diagnose and find more CSR compatibility bugs in the
future and it will save a lot of headaches.
Given that clones come from a wide array of vendors (some are actually
Barrot, some are something else) and these numbers are what let us find
differences between actual and fake ones, it will be immensely helpful
to scour the Internet looking for this pattern and building an actual
database to find correlations and improve the checks.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A patch series by a Qualcomm engineer essentially removed my
quirk/workaround because they thought it was unnecessary.
It wasn't, and it broke everything again:
https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=*
He argues that the quirk is not necessary because the code should check
if the dongle says if it's supported or not. The problem is that for
these Chinese CSR clones they say that it would work:
= New Index: 00:00:00:00:00:00 (Primary,USB,hci0)
= Open Index: 00:00:00:00:00:00
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
> [hci0] 11.276039
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810)
LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312)
Manufacturer: Cambridge Silicon Radio (10)
...
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 68
> [hci0] 11.668030
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 163 entries
...
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
...
...
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
= Close Index: 00:1A:7D:DA:71:XX
So bring it back wholesale.
Fixes: 63b1a7dd38 ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING")
Fixes: e168f69008 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR")
Fixes: 766ae2422b ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk")
Cc: stable@vger.kernel.org
Cc: Zijun Hu <quic_zijuhu@quicinc.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
While discussing solutions for the teardown problem which results from
circular dependencies between timers and workqueues, where timers schedule
work from their timer callback and workqueues arm the timers from work
items, it was discovered that the recent fix to the QCA code is incorrect.
That commit fixes the obvious problem of using del_timer() instead of
del_timer_sync() and reorders the teardown calls to
destroy_workqueue(wq);
del_timer_sync(t);
This makes it less likely to explode, but it's still broken:
destroy_workqueue(wq);
/* After this point @wq cannot be touched anymore */
---> timer expires
queue_work(wq) <---- Results in a NULL pointer dereference
deep in the work queue core code.
del_timer_sync(t);
Use the new timer_shutdown_sync() function to ensure that the timers are
disarmed, no timer callbacks are running and the timers cannot be armed
again. This restores the original teardown sequence:
timer_shutdown_sync(t);
destroy_workqueue(wq);
which is now correct because the timer core silently ignores potential
rearming attempts which can happen when destroy_workqueue() drains pending
work before mopping up the workqueue.
Fixes: 72ef98445a ("Bluetooth: hci_qca: Use del_timer_sync() before freeing")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Acked-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/all/87iljhsftt.ffs@tglx
Link: https://lore.kernel.org/r/20221123201625.435907114@linutronix.de
By using skb_put we ensure that skb->tail is set
correctly. Currently, skb->tail is always zero, which
leads to errors, such as the following page fault in
rfcomm_recv_frame:
BUG: unable to handle page fault for address: ffffed1021de29ff
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751)
Fixes: afd2daa26c ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
syzbot is reporting NULL pointer dereference at hci_uart_tty_close() [1],
for rcu_sync_enter() is called without rcu_sync_init() due to
hci_uart_tty_open() ignoring percpu_init_rwsem() failure.
While we are at it, fix that hci_uart_register_device() ignores
percpu_init_rwsem() failure and hci_uart_unregister_device() does not
call percpu_free_rwsem().
Link: https://syzkaller.appspot.com/bug?extid=576dfca25381fb6fbc5f [1]
Reported-by: syzbot <syzbot+576dfca25381fb6fbc5f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 67d2f8781b ("Bluetooth: hci_ldisc: Allow sleeping while proto locks are held.")
Fixes: d73e172816 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
HarrrisonPeak, CyclonePeak, SnowFieldPeak and SandyPeak controllers
are marked to support HCI_QUIRK_LE_STATES.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hardware variant for Magnetor core (CNVi) is added.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it
needs constantly polling control pipe until the host received the WMT
event, thus, we should require to specifically acquire PM counter on the
USB to prevent the interface from entering auto suspended while WMT
cmd/event in progress.
Fixes: a1c49c434e ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Based on photos available from the FCC, all currently supported RTL8761B
series USB dongles have the same chip: RTL8761BUV.
rtl8761bu is often used to refer to this chip.
rtl8761b sometimes refers to this chip, and other times to its
UART variant (RTL8761BTV).
+----------------+---------+---------+---------------+
| Dongle | USB VID | USB PID | FCC ID |
+----------------+---------+---------+---------------+
| ASUS USB-BT500 | 0x0b05 | 0x190e | MSQ-USBBTJB00 |
| TP-Link UB500 | 0x2357 | 0x0604 | 2AXJ4UB500 |
| EDUP EP-B3519 | | | 2AHRD-EPB3519 |
| EDUP EP-B3536 | | | 2AHRDEP-B3536 |
| UGREEN CM390 | | | 2AQI5-CM390 |
+----------------+---------+---------+---------------+
Signed-off-by: Szabolcs Sipos <labuwx@balfug.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Fix up the packet type if ISO packets are sent over the bulk endpoint.
Note: This is a stopgap since the Bluetooth specification currently
doesn't define any endpoint to transport ISO packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Delete the repeated word "that" in comments.
Signed-off-by: shaomin Deng <dengshaomin@cdjrlc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk for fake CSR controllers.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTK controllers
since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576
Signed-off-by: Yuri D'Elia <wavexx@thregr.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add device specific data for max baudrate in autobaud mode. This allows the
host to use a baudrate higher than "init speed" when loading FW in autobaud
mode.
The device specific max baudrate in autobaud mode for CYW55572 is set to
921600 bps. Devices without device specific max baudrate in autobaud mode
will use init speed as before. If no device specific init speed has been
specified, it will default to the bcm_proto default 115200 bps.
The increased baud rate improves FW load time. The exact load time will
depend on the specific system and FW being used. As a rough indication,
the FW load time dropped from ~9s @ 115.2kbps to ~1.7s @ 921.6kbps in one
test.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Always prevent trying to set device baudrate before calling setup() when
using autobaud mode.
This was previously happening for devices which had device specific data
with member no_early_set_baudrate set to 0.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
