This handles the timeout error codes sent by the chip as part of the
bootloader signatures during firmware download process.
When the bootloader does not receive a response packet from the host
within a specific time, it adds an error code to the bootloader
signature while requesting for the FW chunk from the same offset.
The host is expected to clear this error code with a NAK, and reply to
only those bootloader signatures which have error code 0.
However, the driver was ignoring this error code and replying with the
firmware chunks instead, which is apparently ignored by the chip and the
chip resends the same bootloader signature with the error code again. This
happens in a loop until the error code self clears and firmware download
proceeds ahead, adding a couple of milliseconds to the total firmware
download time.
Commit 689ca16e52 was an initial implementation which simply printed
the following line during driver debug:
- FW Download received err 0x04 from chip
This commit adds the expected handling to the error codes.
This error handling is valid for data_req bootloader signatures for V3
and future bootloader versions.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This updates the firmware names of 3 chipsets: w8987, w8997, w9098.
These changes are been done to standardize chip specific firmware
file names to be in sync with firmware names of newer chipsets.
The naming convention for BT-only files would be as follows:
For dual-radio WiFi+BT chipsets:
- <protocol-BT><chip-name>_bt_v<HW-version>.bin
For tri-radio WiFi+BT+15.4 chipsets:
- <protocol-BT><protocol-15.4><chip-name>_bt_v<HW-version>.bin
To maintain backward compatibility, this commit adds a provision to
request older firmware file name, if new firmware file name not found in
/lib/firmware/nxp/.
A new device tree property has been introduced called firmware-name, to
override the hardcoded firmware names (old and new) in the driver.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This new variant needs a different core2_window1 and always uses
beamforming.
The BAR2 also has an offset (RAM start, presumably), so add that.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
[sven: rebased, updated some comments, mentioned 4388 in Kconfig]
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When HCI raw sockets are opened, the Bluetooth kernel module doesn't
track CIS/BIS connections. User-space applications have to identify
ISO data by maintaining connection information and look up the mapping
for each ACL data packet received. Besides, btsnoop log captured in
kernel couldn't tell ISO data from ACL data in this case.
To avoid additional lookups, this patch introduces vendor-specific
packet classification for Intel BT controllers to distinguish
ISO data packets from ACL data packets.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove memset(0) after dma_alloc_coherent(), which already zeroes out
the memory, and fix the following two Coccinelle/coccicheck warnings
reported by zalloc-simple.cocci:
btintel_pcie.c:837:19-37: WARNING: dma_alloc_coherent used in
/* Allocate full chunk of data buffer for DMA first and do indexing and
* initialization next, so it can be freed easily
*/
rxq->buf_v_addr already zeroes out memory, so memset is not needed
btintel_pcie.c:792:19-37: WARNING: dma_alloc_coherent used in
/* Allocate full chunk of data buffer for DMA first and do indexing and
* initialization next, so it can be freed easily
*/
txq->buf_v_addr already zeroes out memory, so memset is not needed
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not
change the former (unlike the latter). This patch has no effect
on runtime behavior.
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
'hci_nokia_radio_hdr' looks like it was unused since it's
initial commit.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Free irq before releasing irq vector.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Firmware sequencer (FSEQ) is a common code shared across Bluetooth
and Wifi. Printing FSEQ will help to debug if there is any mismatch
between Bluetooth and Wifi FSEQ.
Make 'btintel_print_fseq_info' public and use it in btintel_pcie.c.
dmesg:
....
[ 5335.695740] Bluetooth: hci0: Device booted in 33872 usecs
[ 5335.695918] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0190-0291.ddc
[ 5335.697011] Bluetooth: hci0: Applying Intel DDC parameters completed
[ 5335.697837] Bluetooth: hci0: Firmware timestamp 2024.20 buildtype 0 build 62871
[ 5335.697848] Bluetooth: hci0: Firmware SHA1: 0xeffdce06
[ 5335.698655] Bluetooth: hci0: Fseq status: Success (0x00)
[ 5335.698666] Bluetooth: hci0: Fseq executed: 00.00.04.176
[ 5335.698670] Bluetooth: hci0: Fseq BT Top: 00.00.04.176
[ 5335.750204] Bluetooth: MGMT ver 1.22
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the support of MT7922 bluetooth subsystem reset that was called the
auto revert to self-recover from the fatal error in the controller like
the host encounters HCI cmd timeout or the controller crashes.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reset the controller before downloading the firmware to improve its
reliability. This includes situations like cold or warm reboots, ensuring
the controller is in its initial state before starting the firmware
download.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Extract the function btusb_mtk_subsys_reset from the btusb_mtk_reset
for the future handling of resetting bluetooth controller without
the USB reset.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Apply the common btmtk_fw_get_filename to avoid the similar coding in each
driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Include a shared function to get the firmware name, to prevent repeating
code for similar chipsets.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current flow iterates the ACPI table associated with Bluetooth
controller looking for PPAG method. Method name can be directly passed
to acpi_evaluate_object function instead of iterating the table.
Fixes: c585a92b2f ("Bluetooth: btintel: Set Per Platform Antenna Gain(PPAG)")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a new flag BTNXPUART_FW_DOWNLOAD_ABORT which handles the
situation where driver is removed while firmware download is in
progress.
logs:
modprobe btnxpuart
[65239.230431] Bluetooth: hci0: ChipID: 7601, Version: 0
[65239.236670] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se
rmmod btnxpuart
[65241.425300] Bluetooth: hci0: FW Download Aborted
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Tested-by: Guillaume Legoupil <guillaume.legoupil@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BCM4388 takes over 2 seconds to boot, so increase the timeout.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BCM4377_TIMEOUT is always used to wait for completitions and their API
expects a timeout in jiffies instead of msecs.
Fixes: 8a06127602 ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This sets the default power save mode setting to enabled.
The power save feature is now stable and stress test issues, such as the
TX timeout error, have been resolved.
commit c7ee0bc8db32 ("Bluetooth: btnxpuart: Resolve TX timeout error in
power save stress test")
With this setting, the driver will send the vendor command to FW at
startup, to enable power save feature.
User can disable this feature using the following vendor command:
hcitool cmd 3f 23 03 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed
serdev") will cause below regression issue:
BT can't be enabled after below steps:
cold boot -> enable BT -> disable BT -> warm reboot -> BT enable failure
if property enable-gpios is not configured within DT|ACPI for QCA6390.
The commit is to fix a use-after-free issue within qca_serdev_shutdown()
by adding condition to avoid the serdev is flushed or wrote after closed
but also introduces this regression issue regarding above steps since the
VSC is not sent to reset controller during warm reboot.
Fixed by sending the VSC to reset controller within qca_serdev_shutdown()
once BT was ever enabled, and the use-after-free issue is also fixed by
this change since the serdev is still opened before it is flushed or wrote.
Verified by the reported machine Dell XPS 13 9310 laptop over below two
kernel commits:
commit e00fc2700a ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of bluetooth-next tree.
commit b23d98d46d ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of linus mainline tree.
Fixes: 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev")
Cc: stable@vger.kernel.org
Reported-by: Wren Turkal <wt@penguintechs.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218726
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Wren Turkal <wt@penguintechs.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
check pdata return of skb_pull_data, instead of data.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We are releasing a single msgid, so the order argument to
bitmap_release_region must be zero.
Fixes: 8a06127602 ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Cc: stable@vger.kernel.org
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some Broadcom controllers found on Apple Silicon machines abuse the
reserved bits inside the PHY fields of LE Extended Advertising Report
events for additional flags. Add a quirk to drop these and correctly
extract the Primary/Secondary_PHY field.
The following excerpt from a btmon trace shows a report received with
"Reserved" for "Primary PHY" on a 4388 controller:
> HCI Event: LE Meta Event (0x3e) plen 26
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x2515
Props: 0x0015
Connectable
Directed
Use legacy advertising PDUs
Data status: Complete
Reserved (0x2500)
Legacy PDU Type: Reserved (0x2515)
Address type: Random (0x01)
Address: 00:00:00:00:00:00 (Static)
Primary PHY: Reserved
Secondary PHY: No packets
SID: no ADI field (0xff)
TX power: 127 dBm
RSSI: -60 dBm (0xc4)
Periodic advertising interval: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (Apple, Inc.)
Data length: 0x00
Cc: stable@vger.kernel.org
Fixes: 2e7ed5f5e6 ("Bluetooth: hci_sync: Use advertised PHYs on hci_le_ext_create_conn_sync")
Reported-by: Janne Grunau <j@jannau.net>
Closes: https://lore.kernel.org/all/Zjz0atzRhFykROM9@robin
Tested-by: Janne Grunau <j@jannau.net>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Several new features here:
- virtio-net is finally supported in vduse.
- Virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmZN570PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp2JUH/1K3fZOHymop6Y5Z3USFS7YdlF+dniedY/vg
TKyWERkXOlxq1d9DVxC0mN7tk72DweuWI0YJjLXofrEW1VuW29ecSbyFXxpeWJls
b7ErffxDAFRas5jkMCngD8TuFnbEegU0mGP5kbiHpEndBydQ2hH99Gg0x7swW+cE
xsvU5zonCCLwLGIP2DrVrn9qGOHtV6o8eZfVKDVXfvicn3lFBkUSxlwEYsO9RMup
aKxV4FT2Pb1yBicwBK4TH1oeEXqEGy1YLEn+kAHRbgoC/5L0/LaiqrkzwzwwOIPj
uPGkacf8CIbX0qZo5EzD8kvfcYL1xhU3eT9WBmpp2ZwD+4bINd4=
=nax1
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
virtio core already sets the .owner, so driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20240331-module-owner-virtio-v2-7-98f04bfaf46a@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi: Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- renesas_sdhi: Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
- sdhci-acpi: Disable write protect detection on Toshiba WT10-A
- sdhci-acpi: Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654: Re-work and fix the tuning support for multiple speed-modes
- sdhci_am654: Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
- sdhci-of-dwcmshc: Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of PMCSR writes
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback
-----BEGIN PGP SIGNATURE-----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=I2JP
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi:
- Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi:
- Add quirk to enable pull-up on the card-detect GPIO on Asus
T100TA
- Disable write protect detection on Toshiba WT10-A
- Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654:
- Re-work and fix the tuning support for multiple speed-modes
- Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc:
- Add tuning support for Sophgo CV1800B and SG200X
- Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of
PMCSR writes"
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback"
* tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits)
mmc: renesas_sdhi: Add compatible string for RZ/G2L family, RZ/G3S, and RZ/V2M SoCs
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L family compatibility
dt-bindings: mmc: renesas,sdhi: Group single const value items into an enum list
mmc: renesas_sdhi: Set the SDBUF after reset
mmc: core: Increase the timeout period of the ACMD41 command
mmc: core: Convert to use __mmc_poll_for_busy() SD_APP_OP_COND too
mmc: atmel-mci: Switch to use dev_err_probe()
mmc: atmel-mci: Incapsulate used to be a platform data into host structure
mmc: atmel-mci: Replace platform device pointer by generic one
mmc: atmel-mci: Use temporary variable for struct device
mmc: atmel-mci: Get rid of platform data leftovers
mmc: sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
mmc: sdhci-of-dwcmshc: Remove useless "&" of th1520_execute_tuning
mmc: sdhci-s3c: Choose sdhci_ops based on variant
mmc: sdhci_am654: Constify struct sdhci_ops
mmc: sdhci-sprd: Constify struct sdhci_ops
mmc: sdhci-omap: Constify struct sdhci_ops
mmc: sdhci-esdhc-mcf: Constify struct sdhci_ops
mmc: slot-gpio: Use irq_handler_t type
mmc: sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
...
Minor refactor and s/TX_WAIT_TIMEOUT_MS/BTINTEL_PCIE_TX_WAIT_TIMEOUT_MS/g.
Fixes: 6e65a09f92 ("Bluetooth: btintel_pcie: Add *setup* function to download firmware")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix the following compiler warning reported for ARCH=arm
multi_v7_defconfig.
In file included from drivers/bluetooth/hci_ldisc.c:34:
drivers/bluetooth/btintel.h:373:13: warning: 'btintel_hw_error' defined
but not used [-Wunused-function]
373 | static void btintel_hw_error(struct hci_dev *hdev, u8 code)
| ^~~~~~~~~~~~~~~~
cc: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 67d4dbac3b ("Bluetooth: btintel: Export few static functions")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix compiler warnings reported by kernel bot.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202405080647.VRBej6fA-lkp@intel.com/
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add initial code to support Intel bluetooth devices based on PCIe
transport. Allocate memory for TX & RX buffers, internal structures,
initialize interrupts for TX & RX and PCIe device.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some of the functions used in btintel.c is made global so that they can
be reused in other transport drivers apart from USB.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since BT_HS has been remove HCI_AMP controllers no longer has any use so
remove it along with the capability of creating AMP controllers.
Since we no longer need to differentiate between AMP and Primary
controllers, as only HCI_PRIMARY is left, this also remove
hdev->dev_type altogether.
Fixes: e7b02296fb ("Bluetooth: Remove BT_HS")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Return -ENOMEM on allocation failure. Don't return success.
Fixes: cda0d6a198 ("Bluetooth: qca: fix info leak when fetching fw build id")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for BlazarI (cnvi) bluetooth core.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Clean up the QCA driver defines by dropping redundant parentheses around
values and making sure they are aligned (using tabs only).
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Random module versions serves no purpose, what matters is the kernel
version.
Drop the bogus module version which has never been updated.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The skb->data pointer is never NULL so drop the bogus sanity checks when
initialising the EDL header pointer.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Sort usb device id table for enhanced readability.
Signed-off-by: Jiande Lu <jiande.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add HW IDs for wireless module specific to Acer/ASUS
notebook models to ensure proper recognition and functionality.
These HW IDs are extracted from Windows driver inf file.
Note some HW IDs without official drivers, still in testing phase.
Thus, we update module HW ID and test ensure consistent boot success.
Signed-off-by: Jiande Lu <jiande.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Download board id specific NVM instead of default for WCN7850 if board id
is available.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The hardware information surfaced via debugfs might be usable by the
userspace to set some configuration knobs. This patch sets the hw_info
for Intel and Realtek chipsets.
Below are some possible output of the hardware_info debugfs file.
INTEL platform=55 variant=24
RTL lmp_subver=34898 hci_rev=10 hci_ver=11 hci_bus=1
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
USB driver defines macro @USB_CTRL_SET_TIMEOUT for sending control message
timeout and @USB_CTRL_GET_TIMEOUT for receiving, but usb_control_msg()
uses wrong macro @USB_CTRL_SET_TIMEOUT as argument to receive control
message, fixed by using @USB_CTRL_GET_TIMEOUT to receive message.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Because both MT7920 and MT7921 use the same chip ID.
We use the 8th bit of fw_flavor to distingush MT7920.
The original patch made a mistake to check whole fw_flavor,
that makes the condition both true (dev_id == 0x7961 && fw_flavor),
and makes MT7921 flow wrong.
In this patch, we correct the flow to get the 8th bit value for MT7920.
And the patch is verified pass with both MT7920 and MT7921.
Signed-off-by: Peter Tsao <peter.tsao@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes some CHECKs reported by the checkpatch script.
Issues reported in ath3k.c:
-------
ath3k.c
-------
CHECK: Please don't use multiple blank lines
+
+
CHECK: Blank lines aren't necessary after an open brace '{'
+static const struct usb_device_id ath3k_blist_tbl[] = {
+
CHECK: Alignment should match open parenthesis
+static int ath3k_load_firmware(struct usb_device *udev,
+ const struct firmware *firmware)
CHECK: Alignment should match open parenthesis
+ err = usb_bulk_msg(udev, pipe, send_buf, size,
+ &len, 3000);
CHECK: Unnecessary parentheses around 'len != size'
+ if (err || (len != size)) {
CHECK: Alignment should match open parenthesis
+static int ath3k_get_version(struct usb_device *udev,
+ struct ath3k_version *version)
CHECK: Alignment should match open parenthesis
+static int ath3k_load_fwfile(struct usb_device *udev,
+ const struct firmware *firmware)
CHECK: Alignment should match open parenthesis
+ err = usb_bulk_msg(udev, pipe, send_buf, size,
+ &len, 3000);
CHECK: Unnecessary parentheses around 'len != size'
+ if (err || (len != size)) {
CHECK: Blank lines aren't necessary after an open brace '{'
+ switch (fw_version.ref_clock) {
+
CHECK: Alignment should match open parenthesis
+ snprintf(filename, ATH3K_NAME_LEN, "ar3k/ramps_0x%08x_%d%s",
+ le32_to_cpu(fw_version.rom_version), clk_value, ".dfu");
CHECK: Alignment should match open parenthesis
+static int ath3k_probe(struct usb_interface *intf,
+ const struct usb_device_id *id)
CHECK: Alignment should match open parenthesis
+ BT_ERR("Firmware file \"%s\" not found",
+ ATH3K_FIRMWARE);
CHECK: Alignment should match open parenthesis
+ BT_ERR("Firmware file \"%s\" request failed (err=%d)",
+ ATH3K_FIRMWARE, ret);
total: 0 errors, 0 warnings, 14 checks, 540 lines checked
Signed-off-by: Uri Arev <me@wantyapps.xyz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Like the bcm43430a0 the bcm43455 BT does not support the 0xfc45 command
to set the UART clock to 48 MHz and because of this it does not work
at 4000000 baud.
These chips are found on ACPI/x86 devices where the operating baudrate
does not come from the firmware but is hardcoded at 4000000, which does
not work.
Make the driver_data for the "BCM2EA4" ACPI HID which is used for
the bcm43455 BT point to bcm43430_device_data which limits the baudrate
to 2000000.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following CHECKs, WARNINGs, and ERRORs reported in
hci_intel.c
Reported by checkpatch.pl:
-----------
hci_intel.c
-----------
WARNING: Prefer using '"%s...", __func__' to using 'intel_setup', this
function's name, in a string
+ bt_dev_dbg(hdev, "start intel_setup");
ERROR: code indent should use tabs where possible
+ /* Check for supported iBT hardware variants of this firmware$
ERROR: code indent should use tabs where possible
+ * loading method.$
ERROR: code indent should use tabs where possible
+ *$
ERROR: code indent should use tabs where possible
+ * This check has been put in place to ensure correct forward$
ERROR: code indent should use tabs where possible
+ * compatibility options when newer hardware variants come along.$
ERROR: code indent should use tabs where possible
+ */$
CHECK: No space is necessary after a cast
+ duration = (unsigned long long) ktime_to_ns(delta) >> 10;
CHECK: No space is necessary after a cast
+ duration = (unsigned long long) ktime_to_ns(delta) >> 10;
WARNING: Missing a blank line after declarations
+ int err = PTR_ERR(intel->rx_skb);
+ bt_dev_err(hu->hdev, "Frame reassembly failed (%d)", err);
Signed-off-by: Uri Arev <me@wantyapps.xyz>
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use macro for image type instead of using hard code number.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A recent commit fixed the code that parses the firmware files before
downloading them to the controller but introduced a memory leak in case
the sanity checks ever fail.
Make sure to free the firmware buffer before returning on errors.
Fixes: f905ae0be4 ("Bluetooth: qca: add missing firmware sanity checks")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the missing sanity check when fetching the board id to avoid leaking
slab data when later requesting the firmware.
Fixes: a7f8dedb4b ("Bluetooth: qca: add support for QCA2066")
Cc: stable@vger.kernel.org # 6.7
Cc: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the missing sanity checks and move the 255-byte build-id buffer off
the stack to avoid leaking stack data through debugfs in case the
build-info reply is malformed.
Fixes: c0187b0bd3 ("Bluetooth: btqca: Add support to read FW build version for WCN3991 BTSoC")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The default device address apparently comes from the NVM configuration
file and can differ quite a bit between controllers.
Store the default address when parsing the configuration file and use it
to determine whether the controller has been provisioned with an
address.
This makes sure that devices without a unique address start as
unconfigured unless a valid address has been provided in the devicetree.
Fixes: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The NVM configuration files used by WCN3988 and WCN3990/1/8 have two
sets of configuration tags that are enclosed by a type-length header of
type four which the current parser fails to account for.
Instead the driver happily parses random data as if it were valid tags,
something which can lead to the configuration data being corrupted if it
ever encounters the words 0x0011 or 0x001b.
As is clear from commit b63882549b ("Bluetooth: btqca: Fix the NVM
baudrate tag offcet for wcn3991") the intention has always been to
process the configuration data also for WCN3991 and WCN3998 which
encodes the baud rate at a different offset.
Fix the parser so that it can handle the WCN3xxx configuration files,
which has an enclosing type-length header of type four and two sets of
TLV tags enclosed by a type-length header of type two and three,
respectively.
Note that only the first set, which contains the tags the driver is
currently looking for, will be parsed for now.
With the parser fixed, the software in-band sleep bit will now be set
for WCN3991 and WCN3998 (as it is for later controllers) and the default
baud rate 3200000 may be updated by the driver also for WCN3xxx
controllers.
Notably the deep-sleep feature bit is already set by default in all
configuration files in linux-firmware.
Fixes: 4219d46868 ("Bluetooth: btqca: Add wcn3990 firmware download support.")
Cc: stable@vger.kernel.org # 4.19
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the missing sanity checks when parsing the firmware files before
downloading them to avoid accessing and corrupting memory beyond the
vmalloced buffer.
Fixes: 83e81961ff ("Bluetooth: btqca: Introduce generic QCA ROME support")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This address is now used to determine if a controller has a valid
address or if one needs to be provided through devicetree or by user
space before the controller can be used.
It turns out that the WCN3991 controllers used in Chromium Trogdor
machines use a different default address, 39:98:00:00:5a:ad, which also
needs to be marked as invalid so that the correct address is fetched
from the devicetree.
Qualcomm has unfortunately not yet provided any answers as to whether
the 39:98 encodes a hardware id and if there are other variants of the
default address that needs to be handled by the driver.
For now, add the Trogdor WCN3991 default address to the device address
check to avoid having these controllers start with the default address
instead of their assigned addresses.
Fixes: 32868e126c ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Any return value from gpiod_get_optional() other than a pointer to a
GPIO descriptor or a NULL-pointer is an error and the driver should
abort probing. That being said: commit 56d074d26c ("Bluetooth: hci_qca:
don't use IS_ERR_OR_NULL() with gpiod_get_optional()") no longer sets
power_ctrl_enabled on NULL-pointer returned by
devm_gpiod_get_optional(). Restore this behavior but bail-out on errors.
While at it: also bail-out on error returned when trying to get the
"swctrl" GPIO.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Closes: https://lore.kernel.org/linux-bluetooth/1713449192-25926-2-git-send-email-quic_zijuhu@quicinc.com/
Fixes: 56d074d26c ("Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Wren Turkal" <wt@penguintechs.org>
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Krzysztof Kozlowski<krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
setup() is called for a non-serdev controller.
Fixes: e9b3e5b8c6 ("Bluetooth: hci_qca: only assign wakeup with serial port support")
Cc: stable@vger.kernel.org # 6.2
Cc: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
wakeup() is called for a non-serdev controller during suspend.
Just return true for now to restore the original behaviour and address
the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c6
("Bluetooth: hci_qca: only assign wakeup with serial port support") that
causes the crash to happen already at setup() time.
Fixes: c1a74160ea ("Bluetooth: hci_qca: Add device_may_wakeup support")
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_devcd_append() would free the skb on error so the caller don't
have to free it again otherwise it would cause the double free of skb.
Fixes: 0b70151328 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Reported-by : Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This was previously believed to be due to lack of persistent storage for
the address but it may also be due to integrators opting to not use the
on-chip OTP memory and instead store the address elsewhere (e.g. in
storage managed by secure world firmware).
According to Qualcomm, at least WCN6750, WCN6855 and WCN7850 have
on-chip OTP storage for the address.
As the device type alone cannot be used to determine when the address is
valid, instead read back the address during setup() and only set the
HCI_QUIRK_USE_BDADDR_PROPERTY flag when needed.
This specifically makes sure that controllers that have been provisioned
with an address do not start as unconfigured.
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/124a7d54-5a18-4be7-9a76-a12017f6cce5@quicinc.com/
Fixes: 5971752de4 ("Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990")
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btusb_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific
command to trigger firmware coredump, but the command does not
have any event as its sync response, so it is not suitable to use
__hci_cmd_sync(), fixed by using __hci_cmd_send().
Fixes: 20981ce2d5 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 7dcd3e014a.
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc8 ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZfwqow8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNegCffxTbsnbMGjWhVrQ326IJx/DFvNMAoI9csigv
m+G3RzefzZLRx8nAma0c
=GMfc
-----END PGP SIGNATURE-----
Merge tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
dt-bindings: serial: stm32: add power-domains property
serial: 8250_dw: Replace ACPI device check by a quirk
serial: Lock console when calling into driver before registration
serial: 8250_uniphier: Switch to use uart_read_port_properties()
serial: 8250_tegra: Switch to use uart_read_port_properties()
serial: 8250_pxa: Switch to use uart_read_port_properties()
serial: 8250_omap: Switch to use uart_read_port_properties()
serial: 8250_of: Switch to use uart_read_port_properties()
serial: 8250_lpc18xx: Switch to use uart_read_port_properties()
serial: 8250_ingenic: Switch to use uart_read_port_properties()
serial: 8250_dw: Switch to use uart_read_port_properties()
serial: 8250_bcm7271: Switch to use uart_read_port_properties()
serial: 8250_bcm2835aux: Switch to use uart_read_port_properties()
serial: 8250_aspeed_vuart: Switch to use uart_read_port_properties()
serial: port: Introduce a common helper to read properties
serial: core: Add UPIO_UNKNOWN constant for unknown port type
serial: core: Move struct uart_port::quirks closer to possible values
serial: sh-sci: Call sci_serial_{in,out}() directly
serial: core: only stop transmit when HW fifo is empty
serial: pch: Use uart_prepare_sysrq_char().
...
The ATS2851 controller erroneously reports support for the "Read
Encryption Key Length" HCI command. This makes it unable to connect
to any devices, since this command is issued by the kernel during the
connection process in response to an "Encryption Change" HCI event.
Add a new quirk (HCI_QUIRK_BROKEN_ENC_KEY_SIZE) to hint that the command
is unsupported, preventing it from interrupting the connection process.
This is the error log from btmon before this patch:
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 2048 Address: ...
Encryption: Enabled with E0 (0x01)
< HCI Command: Read Encryption Key Size (0x05|0x0008) plen 2
Handle: 2048 Address: ...
> HCI Event: Command Status (0x0f) plen 4
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Vinicius Peixoto <nukelet64@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since dracut refers to the module info for defining the required
firmware files and btmtk driver doesn't provide the firmware info for
MT7922, the generate initrd misses the firmware, resulting in the
broken Bluetooth.
This patch simply adds the MODULE_FIRMWARE() for the missing entry
for covering that.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1214133
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This checks if CONFIG_DEV_COREDUMP is enabled before attempting to clone
the skb and also make sure btmtk_process_coredump frees the skb passed
following the same logic.
Fixes: 0b70151328 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In some cases uart-base drivers may need to use priv data. For
example, to store information needed for devcoredump.
Fixes: 044014ce85 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following build regression:
drivers-bluetooth-btintel.c-btintel_read_version()-warn:
passing-zero-to-PTR_ERR
Fixes: b79e040910 ("Bluetooth: btintel: Fix null ptr deref in btintel_read_version")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The optional variants for the gpiod_get() family of functions return NULL
if the GPIO in question is not associated with this device. They return
ERR_PTR() on any other error. NULL descriptors are graciously handled by
GPIOLIB and can be safely passed to any of the GPIO consumer interfaces
as they will return 0 and act as if the function succeeded. If one is
using the optional variant, then there's no point in checking for NULL.
Fixes: 6845667146 ("Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Firmware sequencer (FSEQ) is a common code shared across Bluetooth
and Wifi. Printing FSEQ will help to debug if there is any mismatch
between Bluetooth and Wifi FSEQ.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use devm_kstrdup() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use strreplace() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If hci_cmd_sync_complete() is triggered and skb is NULL, then
hdev->req_skb is NULL, which will cause this issue.
Reported-and-tested-by: syzbot+830d9e3fa61968246abd@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the tx timeout issue seen while running a stress test on
btnxpuart for couple of hours, such that the interval between two HCI
commands coincide with the power save timeout value of 2 seconds.
Test procedure using bash script:
<load btnxpuart.ko>
hciconfig hci0 up
//Enable Power Save feature
hcitool -i hci0 cmd 3f 23 02 00 00
while (true)
do
hciconfig hci0 leadv
sleep 2
hciconfig hci0 noleadv
sleep 2
done
Error log, after adding few more debug prints:
Bluetooth: btnxpuart_queue_skb(): 01 0A 20 01 00
Bluetooth: hci0: Set UART break: on, status=0
Bluetooth: hci0: btnxpuart_tx_wakeup() tx_work scheduled
Bluetooth: hci0: btnxpuart_tx_work() dequeue: 01 0A 20 01 00
Can't set advertise mode on hci0: Connection timed out (110)
Bluetooth: hci0: command 0x200a tx timeout
When the power save mechanism turns on UART break, and btnxpuart_tx_work()
is scheduled simultaneously, psdata->ps_state is read as PS_STATE_AWAKE,
which prevents the psdata->work from being scheduled, which is responsible
to turn OFF UART break.
This issue is fixed by adding a ps_lock mutex around UART break on/off as
well as around ps_state read/write.
btnxpuart_tx_wakeup() will now read updated ps_state value. If ps_state is
PS_STATE_SLEEP, it will first schedule psdata->work, and then it will
reschedule itself once UART break has been turned off and ps_state is
PS_STATE_AWAKE.
Tested above script for 50,000 iterations and TX timeout error was not
observed anymore.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific command
to trigger firmware coredump, but the command does not have any event as
its sync response, so it is not suitable to use __hci_cmd_sync(), fixed by
using __hci_cmd_send().
Fixes: 06d3fdfcdf ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.
Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.
When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom BCM4377 driver has so far been
setting this flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag, which can simply be replaced
with HCI_QUIRK_USE_BDADDR_PROPERTY to indicate that the default address
is invalid but can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Reported-by: Felix Zhang <mrman@mrman314.tech>
Link: https://lore.kernel.org/r/77419ffacc5b4875e920e038332575a2a5bff29f.camel@mrman314.tech/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Felix Zhang <mrman@mrman314.tech>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
receive_buf() is called from ttyport_receive_buf() that expects values
">= 0" from serdev_controller_receive_buf(), change its return type from
ssize_t to size_t.
The need for this clean-up was noticed while fixing a warning, see
commit 94d0539425 ("Bluetooth: btnxpuart: fix recv_buf() return value").
Changing the callback prototype to return an unsigned seems the best way
to document the API and ensure that is properly used.
GNSS drivers implementation of serdev receive_buf() callback return
directly the return value of gnss_insert_raw(). gnss_insert_raw()
returns a signed int, however this is not an issue since the value
returned is always positive, because of the kfifo_in() implementation.
gnss_insert_raw() could be changed to return also an unsigned, however
this is not implemented here as request by the GNSS maintainer Johan
Hovold.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com> # for platform/surface
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240122180551.34429-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty core
and drivers in here, along with the usual set of rs485 updates (someday
this might work properly...) Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeUaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyOgCgp1uhP/b9iW6qM7qL6OYEG6idI0kAnj0VASNm
vSI69HmdKKwo69YLOSBp
=14n1
-----END PGP SIGNATURE-----
Merge tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove useless assignment of rx_skb to NULL in case the skb is in error,
this is already done in h4_recv_buf() that is executed a few lines
before.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return negative number in case of issue, just print an error and
return count. This fixes a WARN in ttyport_receive_buf().
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return a negative number in case of issue, just print an error
and return count. Before this change, in case of error, the returned
negative number was internally converted to 0 in ttyport_receive_buf,
now when the receive buffer is corrupted we return the size of the whole
received data (`count`). This should allow for better recovery in case
receiver/transmitter get out of sync if some data is lost.
This fixes a WARN in ttyport_receive_buf().
Bluetooth: hci0: Frame reassembly failed (-84)
------------[ cut here ]------------
serial serial0: receive_buf returns -84 (count = 6)
WARNING: CPU: 0 PID: 37 at drivers/tty/serdev/serdev-ttyport.c:37 ttyport_receive_buf+0xd8/0xf8
Modules linked in: mwifiex_sdio(+) ...
CPU: 0 PID: 37 Comm: kworker/u4:2 Not tainted 6.7.0-rc2-00147-gf1a09972a45a #1
Hardware name: Toradex Verdin AM62 WB on Verdin Development Board (DT)
Workqueue: events_unbound flush_to_ldisc
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ttyport_receive_buf+0xd8/0xf8
lr : ttyport_receive_buf+0xd8/0xf8
...
Call trace:
ttyport_receive_buf+0xd8/0xf8
flush_to_ldisc+0xbc/0x1a4
process_scheduled_works+0x16c/0x28c
Closes: https://lore.kernel.org/all/ZWEIhcUXfutb5SY6@francesco-nb.int.toradex.com/
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For QCA2066 HFP offload, HCI_Configure_Data_Path is not required since
present HCI_Enhanced_Setup_Synchronous_Connection is enough to configure
non-HCI data transport path when set both Input_Data_Path and
Output_Data_Path parameters as 0x01, as is implemented by this change.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Intel Read Version event contains a TLV(0x32) having firmware sha1 in
operational image.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This checks if there are connections before suspending since that may
disrupt the connections making it stop receiving any data if remote
wakeup is not enabled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks
for QCA2066.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Switch character types to u8 and sizes to size_t. To conform to
characters/sizes in the rest of the tty layer.
This patch converts struct serdev_device_ops hooks and its
instantiations.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20231206073712.17776-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BTMTKSDIO_BT_WAKE_ENABLED flag is set for bluetooth interrupt
during system suspend and increases wakeup count for bluetooth event.
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds support for QCA2066 firmware patch and NVM downloading.
as the RF performance of QCA2066 SOC chip from different foundries may
vary. Therefore we use different NVM to configure them based on board ID.
Changes in v2
- optimize the function qca_generate_hsp_nvm_name
- remove redundant debug code for function qca_read_fw_board_id
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If CONFIG_DEV_COREDUMP was not set, it would return -EOPNOTSUPP for
hci_devcd_register().
In this commit, ignore error return for hci_devcd_register().
Otherwise Bluetooth initialization will be failed.
Fixes: 044014ce85 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Cc: stable@vger.kernel.org
Reported-by: Kirill A. Shutemov <kirill@shutemov.name>
Closes: https://lore.kernel.org/all/ZRyqIn0_qqEFBPdy@debian.me/T/
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When the vhci device is opened in the two-step way, i.e.: open device
then write a vendor packet with requested controller type, the device
shall respond with a vendor packet which includes HCI index of created
interface.
When the virtual HCI is created, the host sends a reset request to the
controller. This request is processed by the vhci_send_frame() function.
However, this request is send by a different thread, so it might happen
that this HCI request will be received before the vendor response is
queued in the read queue. This results in the HCI vendor response and
HCI reset request inversion in the read queue which leads to improper
behavior of btvirt:
> dmesg
[1754256.640122] Bluetooth: MGMT ver 1.22
[1754263.023806] Bluetooth: MGMT ver 1.22
[1754265.043775] Bluetooth: hci1: Opcode 0x c03 failed: -110
In order to synchronize vhci two-step open/setup process with virtual
HCI initialization, this patch adds internal lock when queuing data in
the vhci_send_frame() function.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We should send hci reset command before bt turn off, which can reset bt
firmware status.
Signed-off-by: Rocky Liao <quic_rjliao@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
It is not allowed to call kfree_skb() from hardware interrupt
context or with hardware interrupts being disabled.
So replace kfree_skb() with dev_kfree_skb_irq() under
spin_lock_irqsave(). Compile tested only.
Fixes: baac6276c0 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The quirks table was named "blacklist_table" which isn't a good
description for that table as devices detected using it weren't ignored
by the driver.
Rename the table to match what it actually does.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the WCN7850 Bluetooth chipset.
Tested on the SM8550 QRD platform.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use switch/case to handle soc type specific behaviour,
the permit dropping the qca_is_xxx() inline functions
and make the code clearer and easier to update for new
SoCs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This improves the inband IR command handling for NXP BT chipsets.
When the IR vendor command is received, the driver injects a HW
error event, which causes a reset sequence in hci_error_reset().
The vendor IR command is sent to the controller while hci dev
is been closed, and FW is re-downloaded when nxp_setup() is
called during hci_dev_do_open().
The HCI_SETUP flag is set in nxp_hw_err() to make sure that
nxp_setup() is been called during hci_dev_do_open().
This also makes the nxp_setup() and power save functions more
generic.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for NXP IW624 chipset in btnxpuart driver
by adding FW name and bootloader signature. Based on the
loader version bits 7:6 of the bootloader signature, the
driver can choose between selecting secure and non-secure
FW files.
For cmd5 payload during FW download, this chip has addresses
of few registers offset by 1, so added boot_reg_offset to
handle the chip specific offset.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the unnecessary check for CTS low after FW download.
After FW download is complete, the CTS line is already seen low.
It becomes high after 2 msec, and low again after FW initialization
is complete.
This makes the current check for CTS low redundant.
This removes the wait for CTS low section and increase delay to
1200msec instead, which is sufficiant for all NXP chipsets to
initialize FW.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some hooks in struct tty_ldisc_ops still reference buffers by 'unsigned
char'. Unify to 'u8' as the rest of the tty layer does.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810091510.13006-32-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes all those 'char's an explicit 'u8'. This is part of the
continuing unification of chars and flags to be consistent u8.
This approaches tty_port_default_receive_buf().
Note that we do not change signedness as we compile with
-funsigned-char.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-18-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Count passed to tty_ldisc_ops::receive_buf*(), ::lookahead_buf(), and
returned from ::receive_buf2() is expected to be size_t. So set it to
size_t to unify with the rest of the code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_ops::poll() is optional and needs not be provided. It is equal
to returning 0. So remove all those from the code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810091510.13006-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this commit, prefer to load FW v2 if available. Fallback to FW v1
otherwise. This behavior is only for RTL8852C.
Fixes: 9a24ce5e29 ("Bluetooth: btrtl: Firmware format v2 support")
Cc: stable@vger.kernel.org
Suggested-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btusb_recv_event_intel is specific to Intel controllers therefore it
shall be placed inside btintel.c so btusb don't have a mix of vendor
specific code with the generic parts.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the Bluetooth chip codenamed APACHE which is part of
WCN3988.
The firmware for this chip has a slightly different naming scheme
compared to most others. For ROM Version 0x0200 we need to use
apbtfw10.tlv + apnv10.bin and for ROM version 0x201 apbtfw11.tlv +
apnv11.bin
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for NXP AW693 chipset in btnxpuart driver
by adding FW name and bootloader signature. Based on the
loader version bits 7:6 of the bootloader signature, the
driver can choose between selecting secure and non-secure
FW files.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
in nokia_bluetooth_serdev_probe(), check the return value of
clk_prepare_enable() and return the error code if
clk_prepare_enable() returns an unexpected value.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The BCM43430A1 has a default MAC address of AA:AA:AA:AA:AA:AA.
Although, unlike some other entries, this does not include the
chip name, it is clearly not a real address. This was found in
AzureWave AW-NB197SM and AW-NM372SM modules.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
