[ Upstream commit 7868ed0144 ]
Pins 83-86 and 158-160 are NC, so there's no point in keeping them
reserved. Take care of that.
Fixes: 32c231385e ("arm64: dts: qcom: sc8280xp: add Lenovo Thinkpad X13s devicetree")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230803-topic-x13s_pin-v1-1-fae792274e89@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f828f3207 ]
The MMSS SMMU has its own power domain. Attach it so that we can drop
the "keep it always-on" hack.
Fixes: 05ce21b544 ("arm64: dts: qcom: msm8998: Configure the multimedia subsystem iommu")
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230531-topic-8998_mmssclk-v3-2-ba1b1fd9ee75@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4facccb44a ]
There are two control lines controlled by GPIO going into ov5640
- Reset
- Powerdown
The driver and yaml expect "reset-gpios" and "powerdown-gpios" there has
never been an "enable-gpios".
Fixes: 39e0ce6cd1 ("arm64: dts: qcom: apq8016-sbc: Add CCI/Sensor nodes")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811234738.2859417-6-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41e22c2ff3 ]
MSM8916 is the only ARM64 Qualcomm SoC that is still using the old
&msmgpio name. Change this to &tlmm to avoid confusion.
Note that the node ordering does not change because the MSM8916 device
trees have pinctrl separated at the bottom (similar to sc7180).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-1-bec0f5fb46fb@gerhold.net
Stable-dep-of: 4facccb44a ("arm64: dts: qcom: apq8016-sbc: Rename ov5640 enable-gpios to powerdown-gpios")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0a8f16ae4 ]
Right now each MSM8916 device has a huge block of regulator constraints
with allowed voltages for each regulator. For lack of better
documentation these voltages are often copied as-is from the vendor
device tree, without much extra thought.
Unfortunately, the voltages in the vendor device trees are often
misleading or even wrong, e.g. because:
- There is a large voltage range allowed and the actual voltage is
only set somewhere hidden in some messy vendor driver. This is often
the case for pm8916_{l14,l15,l16} because they have a broad range of
1.8-3.3V by default.
- The voltage is actually wrong but thanks to the voltage constraints
in the RPM firmware it still ends up applying the correct voltage.
To have proper regulator constraints it is important to review them in
context of the usage. The current setup in the MSM8916 device trees
makes this quite hard because each device duplicates the standard
voltages for components of the SoC and mixes those with minor
device-specific additions and dummy voltages for completely unused
regulators.
The actual usage of the regulators for the SoC components is in
msm8916-pm8916.dtsi, so it can and should also define the related
voltage constraints. These are not board-specific but defined in the
APQ8016E/PM8916 Device Specification. The board DT can then focus on
describing the actual board-specific regulators, which makes it much
easier to review and spot potential mistakes there.
Note that this commit does not make any functional change. All used
regulators still have the same regulator constraints as before. Unused
regulators do not have regulator constraints anymore because most of
these were too broad or even entirely wrong. They should be added back
with proper voltage constraints when there is an actual usage.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-7-54d4960a05fc@gerhold.net
Stable-dep-of: 4facccb44a ("arm64: dts: qcom: apq8016-sbc: Rename ov5640 enable-gpios to powerdown-gpios")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5cf21b146 ]
Not every device has something connected to the digital audio codec
in MSM8916 and/or the analog audio codec in PM8916. Disable those by
default so the hardware is only powered up when necessary.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-4-54d4960a05fc@gerhold.net
Stable-dep-of: 4facccb44a ("arm64: dts: qcom: apq8016-sbc: Rename ov5640 enable-gpios to powerdown-gpios")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 355750828c ]
The regulator constraints for most MSM8916 devices (except DB410c) were
originally taken from Qualcomm's msm-3.10 vendor device tree (for lack
of better documentation). Unfortunately it turns out that Qualcomm's
voltages are slightly off as well and do not match the voltage
constraints applied by the RPM firmware.
This means that we sometimes request a specific voltage but the RPM
firmware actually applies a much lower or higher voltage. This is
particularly critical for pm8916_l11 which is used as SD card VMMC
regulator: The SD card can choose a voltage from the current range of
1.8 - 2.95V. If it chooses to run at 1.8V we pretend that this is fine
but the RPM firmware will still silently end up configuring 2.95V.
This can be easily reproduced with a multimeter or by checking the
SPMI hardware registers of the regulator.
Fix this by making the voltages match the actual "specified range" in
the PM8916 Device Specification which is enforced by the RPM firmware.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-3-54d4960a05fc@gerhold.net
Stable-dep-of: 4facccb44a ("arm64: dts: qcom: apq8016-sbc: Rename ov5640 enable-gpios to powerdown-gpios")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43a6845808 ]
The ov5640 driver expects DOVDD, AVDD and DVDD as regulator supply names.
The ov5640 has depended on these names since the driver was committed
upstream in 2017. Similarly apq8016-sbc.dtsi has had completely different
regulator names since its own initial commit in 2020.
Perhaps the regulators were left on in previous 410c bootloaders. In any
case today on 6.5 we won't switch on the ov5640 without correctly naming
the regulators.
Fixes: 39e0ce6cd1 ("arm64: dts: qcom: apq8016-sbc: Add CCI/Sensor nodes")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811234738.2859417-3-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73387da70f ]
The Display Data Channel (DDC) transactions between an HDMI transmitter
(SIL9022A in this case) and an HDMI monitor, occur at a maximum of
100KHz. That's the maximum supported frequency within DDC standards.
While the SIL9022A can transact with the core at 400KHz, it needs to
drop the frequency to 100KHz when communicating with the monitor,
otherwise, the i2c controller times out and shows warning like this.
[ 985.773431] omap_i2c 20010000.i2c: controller timed out
That feature, however, has not been enabled in the SIL9022 driver.
Since, dropping the frequency doesn't affect any other devices on the
bus, drop the main-i2c1 frequency from 400KHz to 100KHz.
Fixes: a841581451 ("arm64: dts: ti: Refractor AM625 SK dts")
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20230809084559.17322-2-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574e4099d7 ]
The SoM A uses the EQOS ethernet interface and not the FEC, so drop the
interface pinctrl node from the device tree.
Fixes: c86d350aae ("arm64: dts: Add device tree for the Debix Model A Board")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05a1f13010 ]
This patch fixes the interrupt range for wakeup and main domain gpio
interrupt routers. They were wrongly subtracted by 32 instead of
following what is defined in the interrupt map in the TRM (Table 9-35).
Link: http://www.ti.com/lit/pdf/spruj52
Fixes: 4664ebd834 ("arm64: dts: ti: Add initial support for J784S4 SoC")
Signed-off-by: Apelete Seketeli <aseketeli@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20230810-tps6594-v6-4-2b2e2399e2ef@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9e45dfee ]
Even though currently there is no consumer for L1B, add the supply
for it anyway.
Fixes: 71342fb91e ("arm64: dts: qcom: Add base SM8550 MTP dts")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230801095246.2884770-1-abel.vesa@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9568d22ce ]
I2C6 and I2C7 use the same interrupts, which is incorrect.
In the downstream kernel, I2C7 has interrupts of 608 instead of 607.
Fixes: 81bee6953b ("arm64: dts: qcom: sm8150: add i2c nodes")
Signed-off-by: Zeyan Li <qaz6750@outlook.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/SY7P282MB378712225CBCEA95FE71554DB201A@SY7P282MB3787.AUSP282.PROD.OUTLOOK.COM
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bdfe84fbd ]
The M.2 KEY B port can be used for WWAN USB2 modules or SATA drives.
Enable sata1 node to fix use of SATA drives on the M.2 slot.
Fixes: 2bf2f4d9f6 ("arm64: dts: rockchip: Add Radxa CM3I E25")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230724145213.3833099-1-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a87852e37f ]
Despite its name, the regulator vcc3v3_pcie30x1 has nothing to do with
pcie30x1. Instead, it supply power to VBAT1-5 on the M.2 KEY B port as
seen on page 8 of the schematic [1].
pcie30x1 is used for the mini PCIe slot, and as seen on page 9 the
vcc3v3_minipcie regulator is instead related to pcie30x1.
The M.2 KEY B port can be used for WWAN USB2 modules or SATA drives.
Use correct regulator vcc3v3_minipcie for pcie30x1.
[1] https://dl.radxa.com/cm3p/e25/radxa-e25-v1.4-sch.pdf
Fixes: 2bf2f4d9f6 ("arm64: dts: rockchip: Add Radxa CM3I E25")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230724145213.3833099-1-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21fc24ee9c ]
According to bindings and Linux driver, there is no VDDA but VIO supply.
Fixes: 4ac46b3682 ("arm64: dts: qcom: msm8996: xiaomi-gemini: Add support for Xiaomi Mi 5")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720115335.137354-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b6ea15c0a ]
GCC and it's GDSCs are under the RPMh CX power domain. So let's add the
missing RPMh power domain to the GCC node.
Fixes: 6d4cf750d0 ("arm64: dts: sdm845: Add minimal dts/dtsi files for sdm845 SoC and MTP")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230720054100.9940-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 590bfe5183 ]
After commit 71de0a054d ("arm64: tegra: Drop serial clock-names and
reset-names") was applied, the HSUART failed to probe and the following
error is seen:
serial-tegra 70006300.serial: Couldn't get the reset
serial-tegra: probe of 70006300.serial failed with error -2
Commit 71de0a054d ("arm64: tegra: Drop serial clock-names and
reset-names") is correct because the "reset-names" property is not
needed for 8250 UARTs. However, the "reset-names" is required for the
HSUART and should have been populated as part of commit a63c0cd837
("arm64: dts: tegra: smaug: Add Bluetooth node") that enabled the HSUART
for the Pixel C. Fix this by populating the "reset-names" property for
the HSUART on the Pixel C.
Fixes: a63c0cd837 ("arm64: dts: tegra: smaug: Add Bluetooth node")
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861dbb2b15 ]
After commit 71de0a054d ("arm64: tegra: Drop serial clock-names and
reset-names") was applied, the HSUART failed to probe and the following
error is seen:
serial-tegra 3100000.serial: Couldn't get the reset
serial-tegra: probe of 3100000.serial failed with error -2
Commit 71de0a054d ("arm64: tegra: Drop serial clock-names and
reset-names") is correct because the "reset-names" property is not
needed for 8250 UARTs. However, the "reset-names" is required for the
HSUART and should have been populated as part of commit ff578db7b6
("arm64: tegra: Enable UART instance on 40-pin header") that
enabled the HSUART for Jetson AGX Orin. Fix this by populating the
"reset-names" property for the HSUART on Jetson AGX Orin.
Fixes: ff578db7b6 ("arm64: tegra: Enable UART instance on 40-pin header")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 435a73d737 ]
The commit b2de431360 ("arm64: dts: qcom: pmk8350: Add peripherals for
pmk8350") for the ADC TM (thermal monitoring device) have used the
compatible string from the vendor kernel ("qcom,adc-tm7"). Use the
proper compatible string that is defined in the upstream kernel
("qcom,spmi-adc-tm5-gen2").
Fixes: b2de431360 ("arm64: dts: qcom: pmk8350: Add peripherals for pmk8350")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230707123027.1510723-6-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99f8cf491d ]
The name of the thermal zone in pmr735b.dtsi (pmr735a-thermal) conflicts
with the thermal zone in pmr735a.dtsi. Rename the thermal zone according
to the chip name.
Fixes: 6f3426b3de ("arm64: dts: qcom: pmr735b: add temp sensor and thermal zone config")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230707123027.1510723-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aad41d9e6c ]
The name of the thermal zone in pm8350b.dtsi (pm8350c-thermal) conflicts
with the thermal zone in pm8350c.dtsi. Rename the thermal zone according
to the chip name.
Fixes: 5c1399299d ("arm64: dts: qcom: pm8350b: add temp sensor and thermal zone config")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230707123027.1510723-4-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64f19c06f7 ]
The name of the thermal zone in pm8350.dtsi (pm8350c-thermal) conflicts
with the thermal zone in pm8350c.dtsi. Rename the thermal zone according
to the chip name.
Fixes: 7a79b95f42 ("arm64: dts: qcom: pm8350: add temp sensor and thermal zone config")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230707123027.1510723-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91ce3693e2 ]
The present values look to have been copypasted from 8150 or 8180.
Fix that.
Fixes: 07ddb30281 ("arm64: dts: qcom: sm8350: Add CPU topology and idle-states")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230705-topic-sm8350_fixes-v1-2-0f69f70ccb6a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9acc60c3e2 ]
UART6 is used for debug (routed via uSD pins) and UART9 is connected
to the bluetooth chip.
Set indexed aliases to make the GENI UART driver happy and route serial
traffic through the debug uart by default.
Fixes: 30a7f99bef ("arm64: dts: qcom: Add support for SONY Xperia XZ2 / XZ2C / XZ3 (Tama platform)")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230627-topic-tama_uart-v1-1-0fa790248db8@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36541089c4 ]
The interrupt line was previously not described. Take care of that.
Fixes: 1e39255ed2 ("arm64: dts: msm8996: Add device node for qcom,dwc3")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230627-topic-more_bindings-v1-11-6b4b6cd081e5@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a422c6a91a ]
Set up the corresponding GPIOs properly and add the leftover hardware
buttons to mark this piece of the puzzle complete.
Fixes: 46e14907c7 ("arm64: dts: qcom: sm8250-edo: Add hardware keys")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230614-topic-edo_pinsgpiopmic-v2-4-6f90bba54c53@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b8a633507 ]
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX203&206 DTSIs to better document the hardware.
Diff between 203 and 206:
pm8009_gpios
< "CAM_PWR_LD_EN",
> "NC",
pm8150_gpios
< "NC",
> "G_ASSIST_N",
< "WLC_EN_N", /* GPIO_10 */
> "NC", /* GPIO_10 */
Which is due to 5 II having an additional Google Assistant hardware
button and 1 II having a wireless charger & different camera wiring
to accommodate the additional 3D iToF sensor.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230614-topic-edo_pinsgpiopmic-v2-2-6f90bba54c53@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Stable-dep-of: a422c6a91a ("arm64: dts: qcom: sm8250-edo: Rectify gpio-keys")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40b398beab ]
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX203&206 DTSIs to better document the hardware.
Diff between 203 and 206:
< "CAM_PWR_A_CS",
> "FRONTC_PWR_EN",
< "CAM4_MCLK",
< "TOF_RST_N",
> "NC",
> "NC",
< "WLC_I2C_SDA",
< "WLC_I2C_SCL", /* GPIO_120 */
> "NC",
> "NC",
< "WLC_INT_N",
> "NC",
Which makes sense, as 203 has a 3D iToF, slightly different camera
power wiring and WLC (WireLess Charging).
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230614-topic-edo_pinsgpiopmic-v2-1-6f90bba54c53@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Stable-dep-of: a422c6a91a ("arm64: dts: qcom: sm8250-edo: Rectify gpio-keys")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 775a5283c2 ]
sm8250 faces the same problem with its Energy Model as sdm845. The energy
cost of LITTLE cores is reported to be higher than medium or big cores
EM computes the energy with formula:
energy = OPP's cost / maximum cpu capacity * utilization
On v6.4-rc6 we have:
max capacity of CPU0 = 284
capacity of CPU0's OPP(1612800 Hz) = 253
cost of CPU0's OPP(1612800 Hz) = 191704
max capacity of CPU4 = 871
capacity of CPU4's OPP(710400 Hz) = 255
cost of CPU4's OPP(710400 Hz) = 343217
Both OPPs have almost the same compute capacity but the estimated energy
per unit of utilization will be estimated to:
energy CPU0 = 191704 / 284 * 1 = 675
energy CPU4 = 343217 / 871 * 1 = 394
EM estimates that little CPU0 will consume 71% more than medium CPU4 for
the same compute capacity. According to [1], little consumes 25% less than
medium core for Coremark benchmark at those OPPs for the same duration.
Set the dynamic-power-coefficient of CPU0-3 to 105 to fix the energy model
for little CPUs.
[1] https://github.com/kdrag0n/freqbench/tree/master/results/sm8250/k30s
Fixes: 6aabed5526 ("arm64: dts: qcom: sm8250: Add CPU capacities and energy model")
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20230615154852.130076-1-vincent.guittot@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44bcded2be ]
The previous ZAP region definition was wrong. Fix it.
Note this is not a device-specific fixup, but a fixup to the generic
PIL load address.
Fixes: 5f82b9cda6 ("arm64: dts: qcom: Add SM6350 device tree")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230315-topic-lagoon_gpu-v2-6-afcdfb18bb13@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d6f7e3938 ]
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230707063335.13317-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfa12c32b9 ]
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230707063335.13317-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
