commit 4241665e6e upstream.
A read operation is happening as follows:
a) Set sensor to forced mode
b) Sensor measures values and update data registers and sleeps again
c) Read data registers
In the current implementation the read operation happens immediately
after the sensor is set to forced mode so the sensor does not have
the time to update properly the registers. This leads to the following
2 problems:
1) The first ever value which is read by the register is always wrong
2) Every read operation, puts the register into forced mode and reads
the data that were calculated in the previous conversion.
This behaviour was tested in 2 ways:
1) The internal meas_status_0 register was read before and after every
read operation in order to verify that the data were ready even before
the register was set to forced mode and also to check that after the
forced mode was set the new data were not yet ready.
2) Physically changing the temperature and measuring the temperature
This commit adds the waiting time in between the set of the forced mode
and the read of the data. The function is taken from the Bosch BME68x
Sensor API [1].
[1]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L490
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor")
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://lore.kernel.org/r/20240606212313.207550-5-vassilisamir@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdd478c3ae upstream.
There are cases in the compensate functions of the driver that
there could be overflows of variables due to bit shifting ops.
These implications were initially discussed here [1] and they
were mentioned in log message of Commit 1b3bd85927 ("iio:
chemical: Add support for Bosch BME680 sensor").
[1]: https://lore.kernel.org/linux-iio/20180728114028.3c1bbe81@archlinux/
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor")
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://lore.kernel.org/r/20240606212313.207550-4-vassilisamir@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2b8613295 upstream.
The ret variable was not checked after iio_device_release_direct_mode(),
which could possibly cause errors
Fixes: c70df20e31 ("iio: adc: ad7266: claim direct mode during sensor read")
Signed-off-by: Fernando Yang <hagisf@usp.br>
Link: https://lore.kernel.org/r/20240603180757.8560-1-hagisf@usp.br
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 279428df88 ]
The scale value for the temperature channel is (assuming Vref=2.5 and
the datasheet):
376.7897513
When calculating both val and val2 for the temperature scale we
use (3767897513/25) and multiply it by Vref (here I assume 2500mV) to
obtain:
2500 * (3767897513/25) ==> 376789751300
Finally we divide with remainder by 10^9 to get:
val = 376
val2 = 789751300
However, we return IIO_VAL_INT_PLUS_MICRO (should have been NANO) as
the scale type. So when converting the raw temperature value to the
'processed' temperature value we will get (assuming raw=810,
offset=-753):
processed = (raw + offset) * scale_val
= (810 + -753) * 376
= 21432
processed += div((raw + offset) * scale_val2, 10^6)
+= div((810 + -753) * 789751300, 10^6)
+= 45015
==> 66447
==> 66.4 Celcius
instead of the expected 21.5 Celsius.
Fix this issue by changing IIO_VAL_INT_PLUS_MICRO to
IIO_VAL_INT_PLUS_NANO.
Fixes: 56ca9db862 ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Link: https://lore.kernel.org/r/20240501150554.1871390-1-marc.ferland@sonatest.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b004fe3303 ]
The next rework may require an unindentation of a code block in
ad5592r_read_raw(), which would make review a bit more difficult.
This change unindents the code block for reading the scale of the
non-temperature channels.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200706110259.23947-2-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 279428df88 ("iio: dac: ad5592r: fix temperature channel scaling value")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33c53cbf8f ]
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
This also removes unused iio_dev pointers.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 279428df88 ("iio: dac: ad5592r: fix temperature channel scaling value")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dd6b32e76 ]
The current implementation interprets negative values returned from
`dps310_calculate_temp` as error codes.
This has a side effect that when negative temperature values are
calculated, they are interpreted as error.
Fix this by using the return value only for error handling and passing a
pointer for the value.
Fixes: ba6ec48e76 ("iio: Add driver for Infineon DPS310")
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Link: https://lore.kernel.org/r/20240415105030.1161770-2-thomas.haemmerle@leica-geosystems.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 792595bab4 upstream.
Recently, we encounter kernel crash in function rm3100_common_probe
caused by out of bound access of array rm3100_samp_rates (because of
underlying hardware failures). Add boundary check to prevent out of
bound access.
Fixes: 121354b2ec ("iio: magnetometer: Add driver support for PNI RM3100")
Suggested-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: zhili.liu <zhili.liu@ucas.com.cn>
Link: https://lore.kernel.org/r/1704157631-3814-1-git-send-email-zhouzhouyi@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60576e84c1 upstream.
Fix wrong handling of a DMA request where the probing only failed
if -EPROPE_DEFER was returned. Instead, let us fail if a non -ENODEV
value is returned. This makes DMAs explicitly optional. Even if the
DMA request is unsuccessfully, the ADC can still work properly.
We do also handle the defer probe case by making use of dev_err_probe().
Fixes: f438b9da75 ("drivers: iio: ti_am335x_adc: add dma support")
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230925134427.214556-1-w.egorov@phytec.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54cf39ec16 upstream.
The HTU21 offers 4 sampling frequencies: 20, 40, 70 and 120, which are
associated to an index that is used to select the right measurement
resolution and its corresponding measurement time. The current
implementation selects the measurement resolution and the temperature
measurement time properly, but it does not select the right humidity
measurement time in all cases.
In summary, the 40 and 70 humidity measurement times are swapped.
The reason for that is probably the unusual coding for the measurement
resolution. According to the datasheet, the bits [7,0] of the "user
register" are used as follows to select the bit resolution:
--------------------------------------------------
| Bit 7 | Bit 0 | RH | Temp | Trh (us) | Tt (us) |
--------------------------------------------------
| 0 | 0 | 12 | 14 | 16000 | 50000 |
--------------------------------------------------
| 0 | 1 | 8 | 12 | 3000 | 13000 |
--------------------------------------------------
| 1 | 0 | 10 | 13 | 5000 | 25000 |
--------------------------------------------------
| 1 | 1 | 11 | 11 | 8000 | 7000 |
--------------------------------------------------
*This table is available in the official datasheet, page 13/21. I have
just appended the times provided in the humidity/temperature tables,
pages 3/21, 5/21. Note that always a pair of resolutions is selected.
The sampling frequencies [20, 40, 70, 120] are assigned to a linear
index [0..3] which is then coded as follows [1]:
Index [7,0]
--------------
idx 0 0,0
idx 1 1,0
idx 2 0,1
idx 3 1,1
That is done that way because the temperature measurements are being
used as the reference for the sampling frequency (the frequencies and
the temperature measurement times are correlated), so increasing the
index always reduces the temperature measurement time and its
resolution. Therefore, the temperature measurement time array is as
simple as [50000, 25000, 13000, 7000]
On the other hand, the humidity resolution cannot follow the same
pattern because of the way it is coded in the "user register", where
both resolutions are selected at the same time. The humidity measurement
time array is the following: [16000, 3000, 5000, 8000], which defines
the following assignments:
Index [7,0] Trh
-----------------------
idx 0 0,0 16000 -> right, [0,0] selects 12 bits (Trh = 16000)
idx 1 1,0 3000 -> wrong! [1,0] selects 10 bits (Trh = 5000)
idx 2 0,1 5000 -> wrong! [0,1] selects 8 bits (Trh = 3000)
idx 3 1,1 8000 -> right, [1,1] selects 11 bits (Trh = 8000)
The times have been ordered as if idx = 1 -> [0,1] and idx = 2 -> [1,0],
which is not the case for the reason explained above.
So a simple modification is required to obtain the right humidity
measurement time array, swapping the values in the positions 1 and 2.
The right table should be the following: [16000, 5000, 3000, 8000]
Fix the humidity measurement time array with the right idex/value
coding.
[1] The actual code that makes this coding and assigns it to the current
value of the "user register" is the following:
config_reg &= 0x7E;
config_reg |= ((i & 1) << 7) + ((i & 2) >> 1);
Fixes: d574a87cc3 ("Add meas-spec sensors common part")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20231026-topic-htu21_conversion_time-v1-1-bd257dc44209@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3df0e29fb ]
inv_mpu6050_sensor_show() can return -EINVAL or IIO_VAL_INT. Return the
true value rather than only return IIO_VAL_INT.
Fixes: d509844714 ("iio: imu: mpu6050: add calibration offset support")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231030020218.65728-1-suhui@nfschina.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 865b080e32 upstream.
Second interrupt is needed only when touchscreen mode is used, so don't
request it unconditionally. This removes the following annoying warning
during boot:
exynos-adc 14d10000.adc: error -ENXIO: IRQ index 1 not found
Fixes: 2bb8ad9b44 ("iio: exynos-adc: add experimental touchscreen support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20231009101412.916922-1-m.szyprowski@samsung.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd39d9668f upstream.
The ms5611 driver falsely rejects lots of MS5607-02BA03-50 chips
with "PROM integrity check failed" because it doesn't accept a prom crc
value of zero as legitimate.
According to the datasheet for this chip (and the manufacturer's
application note about the PROM CRC), none of the possible values for the
CRC are excluded - but the current code in ms5611_prom_is_valid() ends with
return crc_orig != 0x0000 && crc == crc_orig
Discussed with the driver author (Tomasz Duszynski) and he indicated that
at that time (2015) he was dealing with some faulty chip samples which
returned blank data under some circumstances and/or followed example code
which indicated CRC zero being bad.
As far as I can tell this exception should not be applied anymore; We've
got a few hundred custom boards here with this chip where large numbers
of the prom have a legitimate CRC value 0, and do work fine, but which the
current driver code wrongly rejects.
Signed-off-by: Alexander Zangerl <az@breathe-safe.com>
Fixes: c0644160a8 ("iio: pressure: add support for MS5611 pressure and temperature sensor")
Link: https://lore.kernel.org/r/2535-1695168070.831792@Ze3y.dhYT.s3fx
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 901a293fd9 upstream.
The DPS310 sensor chip has been encountering intermittent errors while
reading the sensor device across various system designs. This issue causes
the chip to become "stuck," preventing the indication of "ready" status
for pressure and temperature measurements in the MEAS_CFG register.
To address this issue, this commit fixes the timeout settings to improve
sensor stability:
- After sending a reset command to the chip, the timeout has been extended
from 2.5 ms to 15 ms, aligning with the DPS310 specification.
- The read timeout value of the MEAS_CFG register has been adjusted from
20ms to 30ms to match the specification.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Fixes: 7b4ab4abce ("iio: pressure: dps310: Reset chip after timeout")
Link: https://lore.kernel.org/r/20230829180222.3431926-2-lakshmiy@us.ibm.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85dfb43bf6 upstream.
The bmp085 EOC IRQ support is optional, but the driver's common probe
function queries the IRQ properties whether or not it exists, which
can trigger a NULL pointer exception. Avoid any exception by making
the query conditional on the possession of a valid IRQ.
Fixes: aae9539496 ("iio: pressure: bmp280: add support for BMP085 EOC interrupt")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230811155829.51208-1-phil@raspberrypi.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f9b80aefb ]
The ADC conversion procedure requires several device I/O operations
performed in a particular sequence. If stx104_read_raw() is called
concurrently, the ADC conversion procedure could be clobbered. Prevent
such a race condition by utilizing a mutex.
Fixes: 4075a283ae ("iio: stx104: Add IIO support for the ADC channels")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/2ae5e40eed5006ca735e4c12181a9ff5ced65547.1680790580.git.william.gray@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9740827468 ]
The priv->chan_out_states array and actual DAC value can become
mismatched if stx104_write_raw() is called concurrently. Prevent such a
race condition by utilizing a mutex.
Fixes: 97a445dad3 ("iio: Add IIO support for the DAC on the Apex Embedded Systems STX104")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/c95c9a77fcef36b2a052282146950f23bbc1ebdc.1680790580.git.william.gray@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 4f9b80aefb ("iio: addac: stx104: Fix race condition when converting analog-to-digital")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73b8390cc2 ]
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/64673797df382c52fc32fce24348b25a0b05e73a.1652201921.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 4f9b80aefb ("iio: addac: stx104: Fix race condition when converting analog-to-digital")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8a4629055e upstream.
The struct cros_ec_command contains several integer fields and a
trailing array. An allocation size neglecting the integer fields can
lead to buffer overrun.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Yiyuan Guo <yguoaz@gmail.com>
Fixes: 974e6f02e2 ("iio: cros_ec_sensors_core: Add common functions for the ChromeOS EC Sensor Hub.")
Link: https://lore.kernel.org/r/20230630143719.1513906-1-yguoaz@gmail.com
Cc: <Stable@vger.kerenl.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c57fa00370 upstream.
According to the datasheets of supported meson SoCs length of ADC_CLK_DIV
field is 6-bit. Although all supported SoCs have the register
with that field documented later SoCs use external clock rather than
ADC internal clock so this patch affects only meson8 family (S8* SoCs).
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230606165357.42417-1-gnstark@sberdevices.ru
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a146eccb68 upstream.
Commit 28d1a7ac2a ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.
Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.
Fixes: 28d1a7ac2a ("iio: dac: Add AD5758 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230508040208.12033-1-lukas.bulwahn@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09d3bec700 upstream.
The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.
Fixes: cf35ad61ac ("iio: add mcp4725 I2C DAC driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230511004330.206942-1-marex@denx.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b2ed5b6d upstream.
Smatch reports:
drivers/iio/adc/mxs-lradc-adc.c:766 mxs_lradc_adc_probe() warn:
missing unwind goto?
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f8 ("iio: adc: mxs-lradc: Add support for ADC driver")
Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b29c49026c ]
The driver currently matches only via i2c_device_id, but also has
of_device_id table:
drivers/iio/light/max44009.c:545:34: error: ‘max44009_of_match’ defined but not used [-Werror=unused-const-variable=]
Fixes: 6aef699a7d ("iio: light: add driver for MAX44009")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312153429.371702-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49f76c499d ]
Calling dev_to_iio_dev() on a platform device pointer is undefined and
will make adc NULL.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230313205029.1881745-1-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 73a428b37b upstream.
The at91_adc_allocate_trigger() function is supposed to return error
pointers. Returning a NULL will cause an Oops.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/5d728f9d-31d1-410d-a0b3-df6a63a2c8ba@kili.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1cb00d51e upstream.
tsl2772_read_prox_diodes() will correctly parse the properties from
device tree to determine which proximity diode(s) to read from, however
it didn't actually set this value on the struct tsl2772_settings. Let's
go ahead and fix that.
Reported-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/lkml/20230327120823.1369700-1-trix@redhat.com/
Fixes: 94cd1113aa ("iio: tsl2772: add support for reading proximity led settings from device tree")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20230404011455.339454-1-bmasney@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3701185ee upstream.
The CIO-DAC series of devices only supports DAC values up to 12-bit
rather than 16-bit. Trying to write a 16-bit value results in only the
lower 12 bits affecting the DAC output which is not what the user
expects. Instead, adjust the DAC write value check to reject values
larger than 12-bit so that they fail explicitly as invalid for the user.
Fixes: 3b8df5fd52 ("iio: Add IIO support for the Measurement Computing CIO-DAC family")
Cc: stable@vger.kernel.org
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230311002248.8548-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 363c7dc72f upstream.
The ads7950 uses a mutex as well as SPI transfers in its GPIO callbacks.
This means these callbacks can sleep and the `can_sleep` flag should be
set.
Having the flag set will make sure that warnings are generated when calling
any of the callbacks from a potentially non-sleeping context.
Fixes: c97dce792d ("iio: adc: ti-ads7950: add GPIO support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20230312210933.2275376-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64a6815873 ]
Smatch Warns:
drivers/iio/accel/mma9551_core.c:299
mma9551_read_config_word() error: uninitialized symbol 'v'.
When (offset >= 1 << 12) is true mma9551_transfer() will return -EINVAL
without 'v' being initialized, so check for the error and return.
Note: No actual bug as caller checks the return value and does not
use the parameter in the problem case.
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230126153610.3586243-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e56d2c34ce ]
Smatch Warns: drivers/iio/accel/mma9551_core.c:357
mma9551_read_status_word() error: uninitialized symbol 'v'.
When (offset >= 1 << 12) is true mma9551_transfer() will return -EINVAL
without 'v' being initialized, so check for the error and return.
Note: Not a bug as such because the caller checks return value and
doesn't not use this parameter in the problem case.
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230126152147.3585874-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bffb7d9d1a ]
VAC needs to be wired up to produce proper measurements,
without this change only near zero values are reported.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 1696f36482 ("iio: twl6030-gpadc: TWL6030, TWL6032 GPADC driver")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221217221305.671117-1-andreas@kemnade.info
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f804bd0dc2 upstream.
Some inputs need to be wired up to produce proper measurements,
without this change only near zero values are reported.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 1696f36482 ("iio: twl6030-gpadc: TWL6030, TWL6032 GPADC driver")
Link: https://lore.kernel.org/r/20221201181635.3522962-1-andreas@kemnade.info
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbd3a0153c upstream.
of_get_parent() will return a device_node pointer with refcount
incremented. We need to use of_node_put() on it when done. Add the
missing of_node_put() in the error path of berlin2_adc_probe();
Fixes: 70f1937911 ("iio: adc: add support for Berlin")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221129020316.191731-1-wangxiongfeng2@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7b23d1c35 upstream.
Return value should be zero for success. This was forgotten for timestamp
feature. Verified on RealSense cameras.
Fixes: a96cd0f901 ("iio: accel: hid-sensor-accel-3d: Add timestamp")
Signed-off-by: Dmitry Perchanov <dmitry.perchanov@intel.com>
Link: https://lore.kernel.org/r/a6dc426498221c81fa71045b41adf782ebd42136.camel@intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc3304052a ]
When STM32 DFSDM driver is built as module, no modalias information
is available. This prevents module to be loaded by udev.
Add MODULE_DEVICE_TABLE() to fill module aliases.
Fixes: e2e6771c64 ("IIO: ADC: add STM32 DFSDM sigma delta ADC support")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20221202152848.45585-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e2af60f590 upstream.
Prior to commit bd5d54e4d4 ("iio: adc128s052: add ACPI _HID
AANT1280"), the driver unconditionally used spi_get_device_id() to get
the index into the adc128_config array.
However, with that commit, OF-based boards now incorrectly treat all
supported sensors as if they are an adc128s052, because all the .data
members of the adc128_of_match table are implicitly 0. Our board,
which has an adc122s021, thus exposes 8 channels whereas it really
only has two.
Fixes: bd5d54e4d4 ("iio: adc128s052: add ACPI _HID AANT1280")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221115132324.1078169-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20228a1d5a upstream.
Drop 'mlock' usage by making use of iio_device_claim_direct_mode().
This change actually makes sure we cannot do a single conversion while
buffering is enable. Note there was a potential race in the previous
code since we were only acquiring the lock after checking if the bus is
enabled.
Fixes: af3008485e ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: <Stable@vger.kernel.org> #No rush as race is very old.
Link: https://lore.kernel.org/r/20220920112821.975359-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ac1230357 ]
Fix an implicit declaration of function error for rpr0521 under some configs
When CONFIG_RPR0521 is enabled without CONFIG_IIO_TRIGGERED_BUFFER,
the build results in "implicit declaration of function" errors, e.g.,
drivers/iio/light/rpr0521.c:434:3: error: implicit declaration of function
'iio_trigger_poll_chained' [-Werror=implicit-function-declaration]
434 | iio_trigger_poll_chained(data->drdy_trigger0);
| ^~~~~~~~~~~~~~~~~~~~~~~~
This fix adds select dependencies to RPR0521's configuration declaration.
Fixes: e12ffd241c ("iio: light: rpr0521 triggered buffer")
Signed-off-by: Paul Gazzillo <paul@pgazz.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216678
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221110214729.ls5ixav5kxpeftk7@device
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc92d9e3de ]
KASAN report out-of-bounds read as follows:
BUG: KASAN: global-out-of-bounds in afe4404_read_raw+0x2ce/0x380
Read of size 4 at addr ffffffffc00e4658 by task cat/278
Call Trace:
afe4404_read_raw
iio_read_channel_info
dev_attr_show
The buggy address belongs to the variable:
afe4404_channel_leds+0x18/0xffffffffffffe9c0
This issue can be reproduce by singe command:
$ cat /sys/bus/i2c/devices/0-0058/iio\:device0/in_intensity6_raw
The array size of afe4404_channel_leds and afe4404_channel_offdacs
are less than channels, so access with chan->address cause OOB read
in afe4404_[read|write]_raw. Fix it by moving access before use them.
Fixes: b36e825764 ("iio: health/afe440x: Use regmap fields")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20221107152010.95937-1-weiyongjun@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58143c1ed5 ]
KASAN report out-of-bounds read as follows:
BUG: KASAN: global-out-of-bounds in afe4403_read_raw+0x42e/0x4c0
Read of size 4 at addr ffffffffc02ac638 by task cat/279
Call Trace:
afe4403_read_raw
iio_read_channel_info
dev_attr_show
The buggy address belongs to the variable:
afe4403_channel_leds+0x18/0xffffffffffffe9e0
This issue can be reproduced by singe command:
$ cat /sys/bus/spi/devices/spi0.0/iio\:device0/in_intensity6_raw
The array size of afe4403_channel_leds is less than channels, so access
with chan->address cause OOB read in afe4403_read_raw. Fix it by moving
access before use it.
Fixes: b36e825764 ("iio: health/afe440x: Use regmap fields")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20221107151946.89260-1-weiyongjun@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17f442e7e4 ]
When using multiple instances of this driver the compensation PROM was
overwritten by the last initialized sensor. Now each sensor has own PROM
storage.
Signed-off-by: Mitja Spes <mitja@lxnav.com>
Fixes: 9690d81a02 ("iio: pressure: ms5611: add support for MS5607 temperature and pressure sensor")
Link: https://lore.kernel.org/r/20221021135827.1444793-2-mitja@lxnav.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc19fa63ad ]
The ms5611 passes &indio_dev->dev as a parameter to all its IO callbacks
only to directly cast the struct device back to struct iio_dev. And the
struct iio_dev is then only used to get the drivers state struct.
Simplify this a bit by passing the state struct directly. This makes it a
bit easier to follow what the code is doing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211020142110.7060-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 17f442e7e4 ("iio: pressure: ms5611: fixed value compensation bug")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4ad09d956f upstream.
In iio_register_sw_trigger_type(), configfs_register_default_group() is
possible to fail, but the entry add to iio_trigger_types_list is not
deleted.
This leaves wild in iio_trigger_types_list, which can cause page fault
when module is loading again. So fix this by list_del(&t->list) in error
path.
BUG: unable to handle page fault for address: fffffbfff81d7400
Call Trace:
<TASK>
iio_register_sw_trigger_type
do_one_initcall
do_init_module
load_module
...
Fixes: b662f809d4 ("iio: core: Introduce IIO software triggers")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221108032802.168623-1-chenzhongjin@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
