commit 4241665e6e upstream.
A read operation is happening as follows:
a) Set sensor to forced mode
b) Sensor measures values and update data registers and sleeps again
c) Read data registers
In the current implementation the read operation happens immediately
after the sensor is set to forced mode so the sensor does not have
the time to update properly the registers. This leads to the following
2 problems:
1) The first ever value which is read by the register is always wrong
2) Every read operation, puts the register into forced mode and reads
the data that were calculated in the previous conversion.
This behaviour was tested in 2 ways:
1) The internal meas_status_0 register was read before and after every
read operation in order to verify that the data were ready even before
the register was set to forced mode and also to check that after the
forced mode was set the new data were not yet ready.
2) Physically changing the temperature and measuring the temperature
This commit adds the waiting time in between the set of the forced mode
and the read of the data. The function is taken from the Bosch BME68x
Sensor API [1].
[1]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L490
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor")
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://lore.kernel.org/r/20240606212313.207550-5-vassilisamir@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdd478c3ae upstream.
There are cases in the compensate functions of the driver that
there could be overflows of variables due to bit shifting ops.
These implications were initially discussed here [1] and they
were mentioned in log message of Commit 1b3bd85927 ("iio:
chemical: Add support for Bosch BME680 sensor").
[1]: https://lore.kernel.org/linux-iio/20180728114028.3c1bbe81@archlinux/
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor")
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Link: https://lore.kernel.org/r/20240606212313.207550-4-vassilisamir@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2b8613295 upstream.
The ret variable was not checked after iio_device_release_direct_mode(),
which could possibly cause errors
Fixes: c70df20e31 ("iio: adc: ad7266: claim direct mode during sensor read")
Signed-off-by: Fernando Yang <hagisf@usp.br>
Link: https://lore.kernel.org/r/20240603180757.8560-1-hagisf@usp.br
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 245f3b149e upstream.
Update watermark will be done inside the hwfifo_set_watermark callback
just after the update_scan_mode. It is useless to do it here.
Fixes: 7f85e42a6c ("iio: imu: inv_icm42600: add buffer support in iio devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240527210008.612932-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 279428df88 upstream.
The scale value for the temperature channel is (assuming Vref=2.5 and
the datasheet):
376.7897513
When calculating both val and val2 for the temperature scale we
use (3767897513/25) and multiply it by Vref (here I assume 2500mV) to
obtain:
2500 * (3767897513/25) ==> 376789751300
Finally we divide with remainder by 10^9 to get:
val = 376
val2 = 789751300
However, we return IIO_VAL_INT_PLUS_MICRO (should have been NANO) as
the scale type. So when converting the raw temperature value to the
'processed' temperature value we will get (assuming raw=810,
offset=-753):
processed = (raw + offset) * scale_val
= (810 + -753) * 376
= 21432
processed += div((raw + offset) * scale_val2, 10^6)
+= div((810 + -753) * 789751300, 10^6)
+= 45015
==> 66447
==> 66.4 Celcius
instead of the expected 21.5 Celsius.
Fix this issue by changing IIO_VAL_INT_PLUS_MICRO to
IIO_VAL_INT_PLUS_NANO.
Fixes: 56ca9db862 ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Link: https://lore.kernel.org/r/20240501150554.1871390-1-marc.ferland@sonatest.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a01ef749b upstream.
According to the IIO documentation, the sign in the scan type should be
lower case. The ad9467 driver was incorrectly using upper case.
Fix by changing to lower case.
Fixes: 4606d0f4b0 ("iio: adc: ad9467: add support for AD9434 high-speed ADC")
Fixes: ad67971202 ("iio: adc: ad9467: add support AD9467 ADC")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240503-ad9467-fix-scan-type-sign-v1-1-c7a1a066ebb9@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9dd6b32e76 ]
The current implementation interprets negative values returned from
`dps310_calculate_temp` as error codes.
This has a side effect that when negative temperature values are
calculated, they are interpreted as error.
Fix this by using the return value only for error handling and passing a
pointer for the value.
Fixes: ba6ec48e76 ("iio: Add driver for Infineon DPS310")
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Link: https://lore.kernel.org/r/20240415105030.1161770-2-thomas.haemmerle@leica-geosystems.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 57a1592784 upstream.
There are 2 issues with interrupt handling in the mxc4005 driver:
1. mxc4005_set_trigger_state() writes MXC4005_REG_INT_MASK1_BIT_DRDYE
(0x01) to INT_MASK1 to enable the interrupt, but to disable the interrupt
it writes ~MXC4005_REG_INT_MASK1_BIT_DRDYE which is 0xfe, so it enables
all other interrupt sources in the INT_SRC1 register. On the MXC4005 this
is not an issue because only bit 0 of the register is used. On the MXC6655
OTOH this is a problem since bit7 is used as TC (Temperature Compensation)
disable bit and writing 1 to this disables Temperature Compensation which
should only be done when running self-tests on the chip.
Write 0 instead of ~MXC4005_REG_INT_MASK1_BIT_DRDYE to disable
the interrupts to fix this.
2. The datasheets for the MXC4005 / MXC6655 do not state what the reset
value for the INT_MASK0 and INT_MASK1 registers is and since these are
write only we also cannot learn this from the hw. Presumably the reset
value for both is all 0, which means all interrupts disabled.
Explicitly set both registers to 0 from mxc4005_chip_init() to ensure
both masks are actually set to 0.
Fixes: 79846e33aa ("iio: accel: mxc4005: add support for mxc6655")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240326113700.56725-2-hdegoede@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cb81840d8 upstream.
The kernel fails when compiling without `CONFIG_REGMAP_I2C` but with
`CONFIG_BMA400`.
```
ld: drivers/iio/accel/bma400_i2c.o: in function `bma400_i2c_probe':
bma400_i2c.c:(.text+0x23): undefined reference to `__devm_regmap_init_i2c'
```
Link: https://download.01.org/0day-ci/archive/20240131/202401311634.FE5CBVwe-lkp@intel.com/config
Fixes: 465c811f1f ("iio: accel: Add driver for the BMA400")
Fixes: 9bea106423 ("iio: accel: bma400: add support for bma400 spi")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240131225246.14169-1-mario.limonciello@amd.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 792595bab4 upstream.
Recently, we encounter kernel crash in function rm3100_common_probe
caused by out of bound access of array rm3100_samp_rates (because of
underlying hardware failures). Add boundary check to prevent out of
bound access.
Fixes: 121354b2ec ("iio: magnetometer: Add driver support for PNI RM3100")
Suggested-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: zhili.liu <zhili.liu@ucas.com.cn>
Link: https://lore.kernel.org/r/1704157631-3814-1-git-send-email-zhouzhouyi@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0080af84 upstream.
In order to avoid unnecessary pollution of the global symbol namespace
move the core/library functions into a specific namespace and import
that into the various specific device drivers that use them.
For more information see https://lwn.net/Articles/760045/
An alternative here would be to conclude that we are unlikely to see
support for the other ad7091r parts in the near future and just merge
the two modules into one supporting just the i2c -5 variant.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-3-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e71c5c89bc ]
The ADC needs a voltage reference to work correctly.
Users can provide an external voltage reference or use the chip internal
reference to operate the ADC.
The availability of an in chip reference for the ADC saves the user from
having to supply an external voltage reference, which makes the external
reference an optional property as described in the device tree
documentation.
Though, to use the internal reference, it must be enabled by writing to
the configuration register.
Enable AD7091R internal voltage reference if no external vref is supplied.
Fixes: 260442cc5b ("iio: adc: ad7091r5: Add scale and external VREF support")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/b865033fa6a4fc4bf2b4a98ec51a6144e0f64f77.1703013352.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020e71c7ff ]
AD7091R-5 devices are supported by the ad7091r-5 driver together with
the ad7091r-base driver. Those drivers declared iio events for notifying
user space when ADC readings fall bellow the thresholds of low limit
registers or above the values set in high limit registers.
However, to configure iio events and their thresholds, a set of callback
functions must be implemented and those were not present until now.
The consequence of trying to configure ad7091r-5 events without the
proper callback functions was a null pointer dereference in the kernel
because the pointers to the callback functions were not set.
Implement event configuration callbacks allowing users to read/write
event thresholds and enable/disable event generation.
Since the event spec structs are generic to AD7091R devices, also move
those from the ad7091r-5 driver the base driver so they can be reused
when support for ad7091r-2/-4/-8 be added.
Fixes: ca69300173 ("iio: adc: Add support for AD7091R5 ADC")
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/59552d3548dabd56adc3107b7b4869afee2b0c3c.1703013352.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 149694f5e7 ]
The ad7091r-base driver sets up an interrupt handler for firing events
when inputs are either above or below a certain threshold.
However, for the interrupt signal to come from the device it must be
configured to enable the ALERT/BUSY/GPO pin to be used as ALERT, which
was not being done until now.
Enable interrupt signals on the ALERT/BUSY/GPO pin by setting the proper
bit in the configuration register.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/e8da2ee98d6df88318b14baf3dc9630e20218418.1702746240.git.marcelo.schmitt1@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 020e71c7ff ("iio: adc: ad7091r: Allow users to configure device events")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b73f08bb7f ]
When reading in_voltage_scale we can get something like:
root@analog:/sys/bus/iio/devices/iio:device2# cat in_voltage_scale
0.038146
However, when reading the available options:
root@analog:/sys/bus/iio/devices/iio:device2# cat
in_voltage_scale_available
2000.000000 2100.000006 2200.000007 2300.000008 2400.000009 2500.000010
which does not make sense. Moreover, when trying to set a new scale we
get an error because there's no call to __ad9467_get_scale() to give us
values as given when reading in_voltage_scale. Fix it by computing the
available scales during probe and properly pass the list when
.read_available() is called.
While at it, change to use .read_available() from iio_info. Also note
that to properly fix this, adi-axi-adc.c has to be changed accordingly.
Fixes: ad67971202 ("iio: adc: ad9467: add support AD9467 ADC")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-4-a4a33bc4d70e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76f028539c ]
The reset gpio was being handled with inverted polarity. This means that
as far as gpiolib is concerned we were actually leaving the pin asserted
(in theory, this would mean reset). However, inverting the polarity in
devicetree made things work. Fix it by doing it the proper way and how
gpiolib expects it to be done.
While at it, moved the handling to it's own function and dropped
'reset_gpio' from the 'struct ad9467_state' as we only need it during
probe. On top of that, refactored things so that we now request the gpio
asserted (i.e in reset) and then de-assert it. Also note that we now use
gpiod_set_value_cansleep() instead of gpiod_direction_output() as we
already request the pin as output.
Fixes: ad67971202 ("iio: adc: ad9467: add support AD9467 ADC")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-1-a4a33bc4d70e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdd07b3ab9 ]
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 76f028539c ("iio: adc: ad9467: fix reset gpio handling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a25a7df518 upstream.
Previous version of ad7091r event handler received the ADC state pointer
and retrieved the iio device from driver data field with dev_get_drvdata().
However, no driver data have ever been set, which led to null pointer
dereference when running the event handler.
Pass the iio device to the event handler and retrieve the ADC state struct
from it so we avoid the null pointer dereference and save the driver from
filling the driver data field.
Fixes: ca69300173 ("iio: adc: Add support for AD7091R5 ADC")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/5024b764107463de9578d5b3b0a3d5678e307b1a.1702746240.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60576e84c1 upstream.
Fix wrong handling of a DMA request where the probing only failed
if -EPROPE_DEFER was returned. Instead, let us fail if a non -ENODEV
value is returned. This makes DMAs explicitly optional. Even if the
DMA request is unsuccessfully, the ADC can still work properly.
We do also handle the defer probe case by making use of dev_err_probe().
Fixes: f438b9da75 ("drivers: iio: ti_am335x_adc: add dma support")
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230925134427.214556-1-w.egorov@phytec.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54cf39ec16 upstream.
The HTU21 offers 4 sampling frequencies: 20, 40, 70 and 120, which are
associated to an index that is used to select the right measurement
resolution and its corresponding measurement time. The current
implementation selects the measurement resolution and the temperature
measurement time properly, but it does not select the right humidity
measurement time in all cases.
In summary, the 40 and 70 humidity measurement times are swapped.
The reason for that is probably the unusual coding for the measurement
resolution. According to the datasheet, the bits [7,0] of the "user
register" are used as follows to select the bit resolution:
--------------------------------------------------
| Bit 7 | Bit 0 | RH | Temp | Trh (us) | Tt (us) |
--------------------------------------------------
| 0 | 0 | 12 | 14 | 16000 | 50000 |
--------------------------------------------------
| 0 | 1 | 8 | 12 | 3000 | 13000 |
--------------------------------------------------
| 1 | 0 | 10 | 13 | 5000 | 25000 |
--------------------------------------------------
| 1 | 1 | 11 | 11 | 8000 | 7000 |
--------------------------------------------------
*This table is available in the official datasheet, page 13/21. I have
just appended the times provided in the humidity/temperature tables,
pages 3/21, 5/21. Note that always a pair of resolutions is selected.
The sampling frequencies [20, 40, 70, 120] are assigned to a linear
index [0..3] which is then coded as follows [1]:
Index [7,0]
--------------
idx 0 0,0
idx 1 1,0
idx 2 0,1
idx 3 1,1
That is done that way because the temperature measurements are being
used as the reference for the sampling frequency (the frequencies and
the temperature measurement times are correlated), so increasing the
index always reduces the temperature measurement time and its
resolution. Therefore, the temperature measurement time array is as
simple as [50000, 25000, 13000, 7000]
On the other hand, the humidity resolution cannot follow the same
pattern because of the way it is coded in the "user register", where
both resolutions are selected at the same time. The humidity measurement
time array is the following: [16000, 3000, 5000, 8000], which defines
the following assignments:
Index [7,0] Trh
-----------------------
idx 0 0,0 16000 -> right, [0,0] selects 12 bits (Trh = 16000)
idx 1 1,0 3000 -> wrong! [1,0] selects 10 bits (Trh = 5000)
idx 2 0,1 5000 -> wrong! [0,1] selects 8 bits (Trh = 3000)
idx 3 1,1 8000 -> right, [1,1] selects 11 bits (Trh = 8000)
The times have been ordered as if idx = 1 -> [0,1] and idx = 2 -> [1,0],
which is not the case for the reason explained above.
So a simple modification is required to obtain the right humidity
measurement time array, swapping the values in the positions 1 and 2.
The right table should be the following: [16000, 5000, 3000, 8000]
Fix the humidity measurement time array with the right idex/value
coding.
[1] The actual code that makes this coding and assigns it to the current
value of the "user register" is the following:
config_reg &= 0x7E;
config_reg |= ((i & 1) << 7) + ((i & 2) >> 1);
Fixes: d574a87cc3 ("Add meas-spec sensors common part")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20231026-topic-htu21_conversion_time-v1-1-bd257dc44209@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3df0e29fb ]
inv_mpu6050_sensor_show() can return -EINVAL or IIO_VAL_INT. Return the
true value rather than only return IIO_VAL_INT.
Fixes: d509844714 ("iio: imu: mpu6050: add calibration offset support")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231030020218.65728-1-suhui@nfschina.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d6b3ea4d9 ]
In the probe function, the driver was reading out the thresholds already
set in the core, which can be configured by the user in the Vivado tools
when the FPGA image is built. However, it later clobbered those values
with zero or maximum values. In particular, the overtemperature shutdown
threshold register was overwritten with the max value, which effectively
prevents the FPGA from shutting down when the desired threshold was
eached, potentially risking hardware damage in that case.
Remove this code to leave the preconfigured default threshold values
intact.
The code was also disabling all alarms regardless of what enable state
they were left in by the FPGA image, including the overtemperature
shutdown feature. Leave these bits in their original state so they are
not unconditionally disabled.
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Link: https://lore.kernel.org/r/20230915001019.2862964-2-robert.hancock@calian.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a9685d1a3 ]
In order to simplify resource management and error paths in probe() and
entirely drop the remove() callback - use devres helpers wherever
possible. Define devm actions for cancelling the delayed work and
disabling the clock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Anand Ashok Dumbre <anandash@xilinx.com>
Reviewed-by: Anand Ashok Dumbre <anandash@xilinx.com>
Link: https://lore.kernel.org/r/20201130142759.28216-4-brgl@bgdev.pl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 8d6b3ea4d9 ("iio: adc: xilinx-xadc: Don't clobber preset voltage/temperature thresholds")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d8fd2a06a ]
It's more elegant to use a helper local variable to store the address
of the underlying struct device than to dereference pdev everywhere.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Anand Ashok Dumbre <anandash@xilinx.com>
Reviewed-by: Anand Ashok Dumbre <anandash@xilinx.com>
Link: https://lore.kernel.org/r/20201130142759.28216-2-brgl@bgdev.pl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 8d6b3ea4d9 ("iio: adc: xilinx-xadc: Don't clobber preset voltage/temperature thresholds")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 865b080e32 upstream.
Second interrupt is needed only when touchscreen mode is used, so don't
request it unconditionally. This removes the following annoying warning
during boot:
exynos-adc 14d10000.adc: error -ENXIO: IRQ index 1 not found
Fixes: 2bb8ad9b44 ("iio: exynos-adc: add experimental touchscreen support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20231009101412.916922-1-m.szyprowski@samsung.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd39d9668f upstream.
The ms5611 driver falsely rejects lots of MS5607-02BA03-50 chips
with "PROM integrity check failed" because it doesn't accept a prom crc
value of zero as legitimate.
According to the datasheet for this chip (and the manufacturer's
application note about the PROM CRC), none of the possible values for the
CRC are excluded - but the current code in ms5611_prom_is_valid() ends with
return crc_orig != 0x0000 && crc == crc_orig
Discussed with the driver author (Tomasz Duszynski) and he indicated that
at that time (2015) he was dealing with some faulty chip samples which
returned blank data under some circumstances and/or followed example code
which indicated CRC zero being bad.
As far as I can tell this exception should not be applied anymore; We've
got a few hundred custom boards here with this chip where large numbers
of the prom have a legitimate CRC value 0, and do work fine, but which the
current driver code wrongly rejects.
Signed-off-by: Alexander Zangerl <az@breathe-safe.com>
Fixes: c0644160a8 ("iio: pressure: add support for MS5611 pressure and temperature sensor")
Link: https://lore.kernel.org/r/2535-1695168070.831792@Ze3y.dhYT.s3fx
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 901a293fd9 upstream.
The DPS310 sensor chip has been encountering intermittent errors while
reading the sensor device across various system designs. This issue causes
the chip to become "stuck," preventing the indication of "ready" status
for pressure and temperature measurements in the MEAS_CFG register.
To address this issue, this commit fixes the timeout settings to improve
sensor stability:
- After sending a reset command to the chip, the timeout has been extended
from 2.5 ms to 15 ms, aligning with the DPS310 specification.
- The read timeout value of the MEAS_CFG register has been adjusted from
20ms to 30ms to match the specification.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Fixes: 7b4ab4abce ("iio: pressure: dps310: Reset chip after timeout")
Link: https://lore.kernel.org/r/20230829180222.3431926-2-lakshmiy@us.ibm.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85dfb43bf6 upstream.
The bmp085 EOC IRQ support is optional, but the driver's common probe
function queries the IRQ properties whether or not it exists, which
can trigger a NULL pointer exception. Avoid any exception by making
the query conditional on the possession of a valid IRQ.
Fixes: aae9539496 ("iio: pressure: bmp280: add support for BMP085 EOC interrupt")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230811155829.51208-1-phil@raspberrypi.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f9b80aefb ]
The ADC conversion procedure requires several device I/O operations
performed in a particular sequence. If stx104_read_raw() is called
concurrently, the ADC conversion procedure could be clobbered. Prevent
such a race condition by utilizing a mutex.
Fixes: 4075a283ae ("iio: stx104: Add IIO support for the ADC channels")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/2ae5e40eed5006ca735e4c12181a9ff5ced65547.1680790580.git.william.gray@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9740827468 ]
The priv->chan_out_states array and actual DAC value can become
mismatched if stx104_write_raw() is called concurrently. Prevent such a
race condition by utilizing a mutex.
Fixes: 97a445dad3 ("iio: Add IIO support for the DAC on the Apex Embedded Systems STX104")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/c95c9a77fcef36b2a052282146950f23bbc1ebdc.1680790580.git.william.gray@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 4f9b80aefb ("iio: addac: stx104: Fix race condition when converting analog-to-digital")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73b8390cc2 ]
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/64673797df382c52fc32fce24348b25a0b05e73a.1652201921.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 4f9b80aefb ("iio: addac: stx104: Fix race condition when converting analog-to-digital")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8a4629055e upstream.
The struct cros_ec_command contains several integer fields and a
trailing array. An allocation size neglecting the integer fields can
lead to buffer overrun.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Yiyuan Guo <yguoaz@gmail.com>
Fixes: 974e6f02e2 ("iio: cros_ec_sensors_core: Add common functions for the ChromeOS EC Sensor Hub.")
Link: https://lore.kernel.org/r/20230630143719.1513906-1-yguoaz@gmail.com
Cc: <Stable@vger.kerenl.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c57fa00370 upstream.
According to the datasheets of supported meson SoCs length of ADC_CLK_DIV
field is 6-bit. Although all supported SoCs have the register
with that field documented later SoCs use external clock rather than
ADC internal clock so this patch affects only meson8 family (S8* SoCs).
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230606165357.42417-1-gnstark@sberdevices.ru
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a146eccb68 upstream.
Commit 28d1a7ac2a ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.
Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.
Fixes: 28d1a7ac2a ("iio: dac: Add AD5758 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230508040208.12033-1-lukas.bulwahn@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e55245d115 upstream.
The AD7192 provides a specific channel configuration where both negative
and positive inputs are connected to AIN2. This was represented in the
ad7192 driver as a IIO channel with .channel = 2 and .extended_name set
to "shorted".
The problem with this approach, is that the driver provided two IIO
channels with the identifier .channel = 2; one "shorted" and the other
not. This goes against the IIO ABI, as a channel identifier should be
unique.
Address this issue by changing "shorted" channels to being differential
instead, with channel 2 vs. itself, as we're actually measuring AIN2 vs.
itself.
Note that the fix tag is for the commit that moved the driver out of
staging. The bug existed before that, but backporting would become very
complex further down and unlikely to happen.
Fixes: b581f748cc ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Co-developed-by: Alisa Roman <alisa.roman@analog.com>
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230330102100.17590-1-paul@crapouillou.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09d3bec700 upstream.
The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.
Fixes: cf35ad61ac ("iio: add mcp4725 I2C DAC driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230511004330.206942-1-marex@denx.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbaae0c79e upstream.
Timestamp reset is not done in the correct place. It must be done
before enabling buffer. The reason is that interrupt timestamping
is always happening when the chip is on, even if the
corresponding sensor is off. When the sensor restarts, timestamp
is wrong if you don't do a reset first.
Fixes: ec74ae9fd3 ("iio: imu: inv_icm42600: add accurate timestamping")
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230509152202.245444-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b2ed5b6d upstream.
Smatch reports:
drivers/iio/adc/mxs-lradc-adc.c:766 mxs_lradc_adc_probe() warn:
missing unwind goto?
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f8 ("iio: adc: mxs-lradc: Add support for ADC driver")
Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b29c49026c ]
The driver currently matches only via i2c_device_id, but also has
of_device_id table:
drivers/iio/light/max44009.c:545:34: error: ‘max44009_of_match’ defined but not used [-Werror=unused-const-variable=]
Fixes: 6aef699a7d ("iio: light: add driver for MAX44009")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312153429.371702-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49f76c499d ]
Calling dev_to_iio_dev() on a platform device pointer is undefined and
will make adc NULL.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230313205029.1881745-1-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 73a428b37b upstream.
The at91_adc_allocate_trigger() function is supposed to return error
pointers. Returning a NULL will cause an Oops.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/5d728f9d-31d1-410d-a0b3-df6a63a2c8ba@kili.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1cb00d51e upstream.
tsl2772_read_prox_diodes() will correctly parse the properties from
device tree to determine which proximity diode(s) to read from, however
it didn't actually set this value on the struct tsl2772_settings. Let's
go ahead and fix that.
Reported-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/lkml/20230327120823.1369700-1-trix@redhat.com/
Fixes: 94cd1113aa ("iio: tsl2772: add support for reading proximity led settings from device tree")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20230404011455.339454-1-bmasney@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
