mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-13 23:34:05 +08:00
ARM: OMAP2+: Remove legacy serial.c
We can now initialize the UARTs using device tree. Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit is contained in:
Tony Lindgren
parent
195c7a52b7
commit
f3b78f7289
@ -6,7 +6,7 @@ ccflags-y := -I$(srctree)/$(src)/include \
|
||||
-I$(srctree)/arch/arm/plat-omap/include
|
||||
|
||||
# Common support
|
||||
obj-y := id.o io.o control.o mux.o devices.o fb.o serial.o timer.o pm.o \
|
||||
obj-y := id.o io.o control.o mux.o devices.o fb.o timer.o pm.o \
|
||||
common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o omap_hwmod.o \
|
||||
omap_device.o omap-headsmp.o sram.o drm.o
|
||||
|
||||
|
||||
@ -1,332 +0,0 @@
|
||||
/*
|
||||
* arch/arm/mach-omap2/serial.c
|
||||
*
|
||||
* OMAP2 serial support.
|
||||
*
|
||||
* Copyright (C) 2005-2008 Nokia Corporation
|
||||
* Author: Paul Mundt <paul.mundt@nokia.com>
|
||||
*
|
||||
* Major rework for PM support by Kevin Hilman
|
||||
*
|
||||
* Based off of arch/arm/mach-omap/omap1/serial.c
|
||||
*
|
||||
* Copyright (C) 2009 Texas Instruments
|
||||
* Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com
|
||||
*
|
||||
* This file is subject to the terms and conditions of the GNU General Public
|
||||
* License. See the file "COPYING" in the main directory of this archive
|
||||
* for more details.
|
||||
*/
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/clk.h>
|
||||
#include <linux/io.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/slab.h>
|
||||
#include <linux/pm_runtime.h>
|
||||
#include <linux/console.h>
|
||||
#include <linux/omap-dma.h>
|
||||
#include <linux/platform_data/serial-omap.h>
|
||||
|
||||
#include "common.h"
|
||||
#include "omap_hwmod.h"
|
||||
#include "omap_device.h"
|
||||
#include "omap-pm.h"
|
||||
#include "soc.h"
|
||||
#include "prm2xxx_3xxx.h"
|
||||
#include "pm.h"
|
||||
#include "cm2xxx_3xxx.h"
|
||||
#include "prm-regbits-34xx.h"
|
||||
#include "control.h"
|
||||
#include "mux.h"
|
||||
#include "serial.h"
|
||||
|
||||
/*
|
||||
* NOTE: By default the serial auto_suspend timeout is disabled as it causes
|
||||
* lost characters over the serial ports. This means that the UART clocks will
|
||||
* stay on until power/autosuspend_delay is set for the uart from sysfs.
|
||||
* This also causes that any deeper omap sleep states are blocked.
|
||||
*/
|
||||
#define DEFAULT_AUTOSUSPEND_DELAY -1
|
||||
|
||||
#define MAX_UART_HWMOD_NAME_LEN 16
|
||||
|
||||
struct omap_uart_state {
|
||||
int num;
|
||||
|
||||
struct list_head node;
|
||||
struct omap_hwmod *oh;
|
||||
struct omap_device_pad default_omap_uart_pads[2];
|
||||
};
|
||||
|
||||
static LIST_HEAD(uart_list);
|
||||
static u8 num_uarts;
|
||||
static u8 console_uart_id = -1;
|
||||
static u8 uart_debug;
|
||||
|
||||
#define DEFAULT_RXDMA_POLLRATE 1 /* RX DMA polling rate (us) */
|
||||
#define DEFAULT_RXDMA_BUFSIZE 4096 /* RX DMA buffer size */
|
||||
#define DEFAULT_RXDMA_TIMEOUT (3 * HZ)/* RX DMA timeout (jiffies) */
|
||||
|
||||
static struct omap_uart_port_info omap_serial_default_info[] __initdata = {
|
||||
{
|
||||
.dma_enabled = false,
|
||||
.dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
|
||||
.dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
|
||||
.dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
|
||||
.autosuspend_timeout = DEFAULT_AUTOSUSPEND_DELAY,
|
||||
},
|
||||
};
|
||||
|
||||
#ifdef CONFIG_PM
|
||||
static void omap_uart_enable_wakeup(struct device *dev, bool enable)
|
||||
{
|
||||
struct platform_device *pdev = to_platform_device(dev);
|
||||
struct omap_device *od = to_omap_device(pdev);
|
||||
|
||||
if (!od)
|
||||
return;
|
||||
|
||||
if (enable)
|
||||
omap_hwmod_enable_wakeup(od->hwmods[0]);
|
||||
else
|
||||
omap_hwmod_disable_wakeup(od->hwmods[0]);
|
||||
}
|
||||
|
||||
#else
|
||||
static void omap_uart_enable_wakeup(struct device *dev, bool enable)
|
||||
{}
|
||||
#endif /* CONFIG_PM */
|
||||
|
||||
#ifdef CONFIG_OMAP_MUX
|
||||
|
||||
#define OMAP_UART_DEFAULT_PAD_NAME_LEN 28
|
||||
static char rx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN],
|
||||
tx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN] __initdata;
|
||||
|
||||
static void __init
|
||||
omap_serial_fill_uart_tx_rx_pads(struct omap_board_data *bdata,
|
||||
struct omap_uart_state *uart)
|
||||
{
|
||||
uart->default_omap_uart_pads[0].name = rx_pad_name;
|
||||
uart->default_omap_uart_pads[0].flags = OMAP_DEVICE_PAD_REMUX |
|
||||
OMAP_DEVICE_PAD_WAKEUP;
|
||||
uart->default_omap_uart_pads[0].enable = OMAP_PIN_INPUT |
|
||||
OMAP_MUX_MODE0;
|
||||
uart->default_omap_uart_pads[0].idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0;
|
||||
uart->default_omap_uart_pads[1].name = tx_pad_name;
|
||||
uart->default_omap_uart_pads[1].enable = OMAP_PIN_OUTPUT |
|
||||
OMAP_MUX_MODE0;
|
||||
bdata->pads = uart->default_omap_uart_pads;
|
||||
bdata->pads_cnt = ARRAY_SIZE(uart->default_omap_uart_pads);
|
||||
}
|
||||
|
||||
static void __init omap_serial_check_wakeup(struct omap_board_data *bdata,
|
||||
struct omap_uart_state *uart)
|
||||
{
|
||||
struct omap_mux_partition *tx_partition = NULL, *rx_partition = NULL;
|
||||
struct omap_mux *rx_mux = NULL, *tx_mux = NULL;
|
||||
char *rx_fmt, *tx_fmt;
|
||||
int uart_nr = bdata->id + 1;
|
||||
|
||||
if (bdata->id != 2) {
|
||||
rx_fmt = "uart%d_rx.uart%d_rx";
|
||||
tx_fmt = "uart%d_tx.uart%d_tx";
|
||||
} else {
|
||||
rx_fmt = "uart%d_rx_irrx.uart%d_rx_irrx";
|
||||
tx_fmt = "uart%d_tx_irtx.uart%d_tx_irtx";
|
||||
}
|
||||
|
||||
snprintf(rx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, rx_fmt,
|
||||
uart_nr, uart_nr);
|
||||
snprintf(tx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, tx_fmt,
|
||||
uart_nr, uart_nr);
|
||||
|
||||
if (omap_mux_get_by_name(rx_pad_name, &rx_partition, &rx_mux) >= 0 &&
|
||||
omap_mux_get_by_name
|
||||
(tx_pad_name, &tx_partition, &tx_mux) >= 0) {
|
||||
u16 tx_mode, rx_mode;
|
||||
|
||||
tx_mode = omap_mux_read(tx_partition, tx_mux->reg_offset);
|
||||
rx_mode = omap_mux_read(rx_partition, rx_mux->reg_offset);
|
||||
|
||||
/*
|
||||
* Check if uart is used in default tx/rx mode i.e. in mux mode0
|
||||
* if yes then configure rx pin for wake up capability
|
||||
*/
|
||||
if (OMAP_MODE_UART(rx_mode) && OMAP_MODE_UART(tx_mode))
|
||||
omap_serial_fill_uart_tx_rx_pads(bdata, uart);
|
||||
}
|
||||
}
|
||||
#else
|
||||
static void __init omap_serial_check_wakeup(struct omap_board_data *bdata,
|
||||
struct omap_uart_state *uart)
|
||||
{
|
||||
}
|
||||
#endif
|
||||
|
||||
static char *cmdline_find_option(char *str)
|
||||
{
|
||||
extern char *saved_command_line;
|
||||
|
||||
return strstr(saved_command_line, str);
|
||||
}
|
||||
|
||||
static int __init omap_serial_early_init(void)
|
||||
{
|
||||
if (of_have_populated_dt())
|
||||
return -ENODEV;
|
||||
|
||||
do {
|
||||
char oh_name[MAX_UART_HWMOD_NAME_LEN];
|
||||
struct omap_hwmod *oh;
|
||||
struct omap_uart_state *uart;
|
||||
char uart_name[MAX_UART_HWMOD_NAME_LEN];
|
||||
|
||||
snprintf(oh_name, MAX_UART_HWMOD_NAME_LEN,
|
||||
"uart%d", num_uarts + 1);
|
||||
oh = omap_hwmod_lookup(oh_name);
|
||||
if (!oh)
|
||||
break;
|
||||
|
||||
uart = kzalloc(sizeof(struct omap_uart_state), GFP_KERNEL);
|
||||
if (WARN_ON(!uart))
|
||||
return -ENODEV;
|
||||
|
||||
uart->oh = oh;
|
||||
uart->num = num_uarts++;
|
||||
list_add_tail(&uart->node, &uart_list);
|
||||
snprintf(uart_name, MAX_UART_HWMOD_NAME_LEN,
|
||||
"%s%d", OMAP_SERIAL_NAME, uart->num);
|
||||
|
||||
if (cmdline_find_option(uart_name)) {
|
||||
console_uart_id = uart->num;
|
||||
|
||||
if (console_loglevel >= CONSOLE_LOGLEVEL_DEBUG) {
|
||||
uart_debug = true;
|
||||
pr_info("%s used as console in debug mode: uart%d clocks will not be gated",
|
||||
uart_name, uart->num);
|
||||
}
|
||||
}
|
||||
} while (1);
|
||||
|
||||
return 0;
|
||||
}
|
||||
omap_postcore_initcall(omap_serial_early_init);
|
||||
|
||||
/**
|
||||
* omap_serial_init_port() - initialize single serial port
|
||||
* @bdata: port specific board data pointer
|
||||
* @info: platform specific data pointer
|
||||
*
|
||||
* This function initialies serial driver for given port only.
|
||||
* Platforms can call this function instead of omap_serial_init()
|
||||
* if they don't plan to use all available UARTs as serial ports.
|
||||
*
|
||||
* Don't mix calls to omap_serial_init_port() and omap_serial_init(),
|
||||
* use only one of the two.
|
||||
*/
|
||||
void __init omap_serial_init_port(struct omap_board_data *bdata,
|
||||
struct omap_uart_port_info *info)
|
||||
{
|
||||
struct omap_uart_state *uart;
|
||||
struct omap_hwmod *oh;
|
||||
struct platform_device *pdev;
|
||||
void *pdata = NULL;
|
||||
u32 pdata_size = 0;
|
||||
char *name;
|
||||
struct omap_uart_port_info omap_up;
|
||||
|
||||
if (WARN_ON(!bdata))
|
||||
return;
|
||||
if (WARN_ON(bdata->id < 0))
|
||||
return;
|
||||
if (WARN_ON(bdata->id >= num_uarts))
|
||||
return;
|
||||
|
||||
list_for_each_entry(uart, &uart_list, node)
|
||||
if (bdata->id == uart->num)
|
||||
break;
|
||||
if (!info)
|
||||
info = omap_serial_default_info;
|
||||
|
||||
oh = uart->oh;
|
||||
name = OMAP_SERIAL_DRIVER_NAME;
|
||||
|
||||
omap_up.dma_enabled = info->dma_enabled;
|
||||
omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
|
||||
omap_up.flags = UPF_BOOT_AUTOCONF;
|
||||
omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
|
||||
omap_up.enable_wakeup = omap_uart_enable_wakeup;
|
||||
omap_up.dma_rx_buf_size = info->dma_rx_buf_size;
|
||||
omap_up.dma_rx_timeout = info->dma_rx_timeout;
|
||||
omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
|
||||
omap_up.autosuspend_timeout = info->autosuspend_timeout;
|
||||
|
||||
pdata = &omap_up;
|
||||
pdata_size = sizeof(struct omap_uart_port_info);
|
||||
|
||||
if (WARN_ON(!oh))
|
||||
return;
|
||||
|
||||
pdev = omap_device_build(name, uart->num, oh, pdata, pdata_size);
|
||||
if (IS_ERR(pdev)) {
|
||||
WARN(1, "Could not build omap_device for %s: %s.\n", name,
|
||||
oh->name);
|
||||
return;
|
||||
}
|
||||
|
||||
oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt);
|
||||
|
||||
if (console_uart_id == bdata->id) {
|
||||
omap_device_enable(pdev);
|
||||
pm_runtime_set_active(&pdev->dev);
|
||||
}
|
||||
|
||||
oh->dev_attr = uart;
|
||||
|
||||
if (((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads)
|
||||
&& !uart_debug)
|
||||
device_init_wakeup(&pdev->dev, true);
|
||||
}
|
||||
|
||||
/**
|
||||
* omap_serial_board_init() - initialize all supported serial ports
|
||||
* @info: platform specific data pointer
|
||||
*
|
||||
* Initializes all available UARTs as serial ports. Platforms
|
||||
* can call this function when they want to have default behaviour
|
||||
* for serial ports (e.g initialize them all as serial ports).
|
||||
*/
|
||||
void __init omap_serial_board_init(struct omap_uart_port_info *info)
|
||||
{
|
||||
struct omap_uart_state *uart;
|
||||
struct omap_board_data bdata;
|
||||
|
||||
list_for_each_entry(uart, &uart_list, node) {
|
||||
bdata.id = uart->num;
|
||||
bdata.flags = 0;
|
||||
bdata.pads = NULL;
|
||||
bdata.pads_cnt = 0;
|
||||
|
||||
omap_serial_check_wakeup(&bdata, uart);
|
||||
|
||||
if (!info)
|
||||
omap_serial_init_port(&bdata, NULL);
|
||||
else
|
||||
omap_serial_init_port(&bdata, &info[uart->num]);
|
||||
}
|
||||
}
|
||||
|
||||
/**
|
||||
* omap_serial_init() - initialize all supported serial ports
|
||||
*
|
||||
* Initializes all available UARTs.
|
||||
* Platforms can call this function when they want to have default behaviour
|
||||
* for serial ports (e.g initialize them all as serial ports).
|
||||
*/
|
||||
void __init omap_serial_init(void)
|
||||
{
|
||||
omap_serial_board_init(NULL);
|
||||
}
|
||||
Loading…
Reference in New Issue
Block a user