mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-12 05:48:39 +08:00
[MIPS] IP27: Convert to clock_event_device.
This separates the tick timer stuff from the generic MIPS time.c. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This commit is contained in:
Ralf Baechle
parent
832348ff0b
commit
e887b24592
@ -374,14 +374,13 @@ int __devinit request_bridge_irq(struct bridge_controller *bc)
|
||||
return irq;
|
||||
}
|
||||
|
||||
extern void ip27_rt_timer_interrupt(void);
|
||||
|
||||
asmlinkage void plat_irq_dispatch(void)
|
||||
{
|
||||
unsigned long pending = read_c0_cause() & read_c0_status();
|
||||
extern unsigned int rt_timer_irq;
|
||||
|
||||
if (pending & CAUSEF_IP4)
|
||||
ip27_rt_timer_interrupt();
|
||||
do_IRQ(rt_timer_irq);
|
||||
else if (pending & CAUSEF_IP2) /* PI_INT_PEND_0 or CC_PEND_{A|B} */
|
||||
ip27_do_irq_mask0();
|
||||
else if (pending & CAUSEF_IP3) /* PI_INT_PEND_1 */
|
||||
|
||||
@ -3,6 +3,7 @@
|
||||
* Copytight (C) 1999, 2000 Silicon Graphics, Inc.
|
||||
*/
|
||||
#include <linux/bcd.h>
|
||||
#include <linux/clockchips.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/sched.h>
|
||||
@ -25,22 +26,8 @@
|
||||
#include <asm/sn/sn0/ip27.h>
|
||||
#include <asm/sn/sn0/hub.h>
|
||||
|
||||
/*
|
||||
* This is a hack; we really need to figure these values out dynamically
|
||||
*
|
||||
* Since 800 ns works very well with various HUB frequencies, such as
|
||||
* 360, 380, 390 and 400 MHZ, we use 800 ns rtc cycle time.
|
||||
*
|
||||
* Ralf: which clock rate is used to feed the counter?
|
||||
*/
|
||||
#define NSEC_PER_CYCLE 800
|
||||
#define CYCLES_PER_SEC (NSEC_PER_SEC/NSEC_PER_CYCLE)
|
||||
#define CYCLES_PER_JIFFY (CYCLES_PER_SEC/HZ)
|
||||
|
||||
#define TICK_SIZE (tick_nsec / 1000)
|
||||
|
||||
static unsigned long ct_cur[NR_CPUS]; /* What counter should be at next timer irq */
|
||||
|
||||
#if 0
|
||||
static int set_rtc_mmss(unsigned long nowtime)
|
||||
{
|
||||
@ -86,36 +73,6 @@ static int set_rtc_mmss(unsigned long nowtime)
|
||||
}
|
||||
#endif
|
||||
|
||||
static unsigned int rt_timer_irq;
|
||||
|
||||
void ip27_rt_timer_interrupt(void)
|
||||
{
|
||||
int cpu = smp_processor_id();
|
||||
int cpuA = cputoslice(cpu) == 0;
|
||||
unsigned int irq = rt_timer_irq;
|
||||
|
||||
irq_enter();
|
||||
write_seqlock(&xtime_lock);
|
||||
|
||||
again:
|
||||
LOCAL_HUB_S(cpuA ? PI_RT_PEND_A : PI_RT_PEND_B, 0); /* Ack */
|
||||
ct_cur[cpu] += CYCLES_PER_JIFFY;
|
||||
LOCAL_HUB_S(cpuA ? PI_RT_COMPARE_A : PI_RT_COMPARE_B, ct_cur[cpu]);
|
||||
|
||||
if (LOCAL_HUB_L(PI_RT_COUNT) >= ct_cur[cpu])
|
||||
goto again;
|
||||
|
||||
kstat_this_cpu.irqs[irq]++; /* kstat only for bootcpu? */
|
||||
|
||||
if (cpu == 0)
|
||||
do_timer(1);
|
||||
|
||||
update_process_times(user_mode(get_irq_regs()));
|
||||
|
||||
write_sequnlock(&xtime_lock);
|
||||
irq_exit();
|
||||
}
|
||||
|
||||
/* Includes for ioc3_init(). */
|
||||
#include <asm/sn/types.h>
|
||||
#include <asm/sn/sn0/addrs.h>
|
||||
@ -154,6 +111,46 @@ unsigned long read_persistent_clock(void)
|
||||
return mktime(year, month, date, hour, min, sec);
|
||||
}
|
||||
|
||||
static int rt_set_next_event(unsigned long delta,
|
||||
struct clock_event_device *evt)
|
||||
{
|
||||
unsigned int cpu = smp_processor_id();
|
||||
int slice = cputoslice(cpu) == 0;
|
||||
unsigned long cnt;
|
||||
|
||||
cnt = LOCAL_HUB_L(PI_RT_COUNT);
|
||||
cnt += delta;
|
||||
LOCAL_HUB_S(slice ? PI_RT_COMPARE_A : PI_RT_COMPARE_B, cnt);
|
||||
|
||||
return LOCAL_HUB_L(PI_RT_COUNT) >= cnt ? -ETIME : 0;
|
||||
}
|
||||
|
||||
static void rt_set_mode(enum clock_event_mode mode,
|
||||
struct clock_event_device *evt)
|
||||
{
|
||||
switch (mode) {
|
||||
case CLOCK_EVT_MODE_PERIODIC:
|
||||
/* The only mode supported */
|
||||
break;
|
||||
|
||||
case CLOCK_EVT_MODE_UNUSED:
|
||||
case CLOCK_EVT_MODE_SHUTDOWN:
|
||||
case CLOCK_EVT_MODE_ONESHOT:
|
||||
case CLOCK_EVT_MODE_RESUME:
|
||||
/* Nothing to do */
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
struct clock_event_device rt_clock_event_device = {
|
||||
.name = "HUB-RT",
|
||||
.features = CLOCK_EVT_FEAT_ONESHOT,
|
||||
|
||||
.rating = 300,
|
||||
.set_next_event = rt_set_next_event,
|
||||
.set_mode = rt_set_mode,
|
||||
};
|
||||
|
||||
static void enable_rt_irq(unsigned int irq)
|
||||
{
|
||||
}
|
||||
@ -171,6 +168,20 @@ static struct irq_chip rt_irq_type = {
|
||||
.eoi = enable_rt_irq,
|
||||
};
|
||||
|
||||
unsigned int rt_timer_irq;
|
||||
|
||||
static irqreturn_t ip27_rt_timer_interrupt(int irq, void *dev_id)
|
||||
{
|
||||
struct clock_event_device *cd = &rt_clock_event_device;
|
||||
unsigned int cpu = smp_processor_id();
|
||||
int slice = cputoslice(cpu) == 0;
|
||||
|
||||
LOCAL_HUB_S(slice ? PI_RT_PEND_A : PI_RT_PEND_B, 0); /* Ack */
|
||||
cd->event_handler(cd);
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static struct irqaction rt_irqaction = {
|
||||
.handler = (irq_handler_t) ip27_rt_timer_interrupt,
|
||||
.flags = IRQF_DISABLED,
|
||||
@ -178,26 +189,43 @@ static struct irqaction rt_irqaction = {
|
||||
.name = "timer"
|
||||
};
|
||||
|
||||
void __init plat_timer_setup(struct irqaction *irq)
|
||||
{
|
||||
int irqno = allocate_irqno();
|
||||
/*
|
||||
* This is a hack; we really need to figure these values out dynamically
|
||||
*
|
||||
* Since 800 ns works very well with various HUB frequencies, such as
|
||||
* 360, 380, 390 and 400 MHZ, we use 800 ns rtc cycle time.
|
||||
*
|
||||
* Ralf: which clock rate is used to feed the counter?
|
||||
*/
|
||||
#define NSEC_PER_CYCLE 800
|
||||
#define CYCLES_PER_SEC (NSEC_PER_SEC / NSEC_PER_CYCLE)
|
||||
|
||||
if (irqno < 0)
|
||||
static void __init ip27_rt_clock_event_init(void)
|
||||
{
|
||||
struct clock_event_device *cd = &rt_clock_event_device;
|
||||
unsigned int cpu = smp_processor_id();
|
||||
int irq = allocate_irqno();
|
||||
|
||||
if (irq < 0)
|
||||
panic("Can't allocate interrupt number for timer interrupt");
|
||||
|
||||
set_irq_chip_and_handler(irqno, &rt_irq_type, handle_percpu_irq);
|
||||
rt_timer_irq = irq;
|
||||
|
||||
/* over-write the handler, we use our own way */
|
||||
irq->handler = no_action;
|
||||
cd->irq = irq,
|
||||
cd->cpumask = cpumask_of_cpu(cpu),
|
||||
|
||||
/* setup irqaction */
|
||||
irq_desc[irqno].status |= IRQ_PER_CPU;
|
||||
|
||||
rt_timer_irq = irqno;
|
||||
/*
|
||||
* Only needed to get /proc/interrupt to display timer irq stats
|
||||
* Calculate the min / max delta
|
||||
*/
|
||||
setup_irq(irqno, &rt_irqaction);
|
||||
cd->mult =
|
||||
div_sc((unsigned long) CYCLES_PER_SEC, NSEC_PER_SEC, 32);
|
||||
cd->shift = 32;
|
||||
cd->max_delta_ns = clockevent_delta2ns(0x7fffffff, cd);
|
||||
cd->min_delta_ns = clockevent_delta2ns(0x300, cd);
|
||||
clockevents_register_device(cd);
|
||||
|
||||
set_irq_chip_and_handler(irq, &rt_irq_type, handle_percpu_irq);
|
||||
setup_irq(irq, &rt_irqaction);
|
||||
}
|
||||
|
||||
static cycle_t hub_rt_read(void)
|
||||
@ -206,7 +234,7 @@ static cycle_t hub_rt_read(void)
|
||||
}
|
||||
|
||||
struct clocksource ht_rt_clocksource = {
|
||||
.name = "HUB",
|
||||
.name = "HUB-RT",
|
||||
.rating = 200,
|
||||
.read = hub_rt_read,
|
||||
.mask = CLOCKSOURCE_MASK(52),
|
||||
@ -214,11 +242,17 @@ struct clocksource ht_rt_clocksource = {
|
||||
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
|
||||
};
|
||||
|
||||
void __init plat_time_init(void)
|
||||
static void __init ip27_rt_clocksource_init(void)
|
||||
{
|
||||
clocksource_register(&ht_rt_clocksource);
|
||||
}
|
||||
|
||||
void __init plat_time_init(void)
|
||||
{
|
||||
ip27_rt_clock_event_init();
|
||||
ip27_rt_clocksource_init();
|
||||
}
|
||||
|
||||
void __init cpu_time_init(void)
|
||||
{
|
||||
lboard_t *board;
|
||||
@ -248,17 +282,12 @@ void __init hub_rtc_init(cnodeid_t cnode)
|
||||
* node and timeouts will not happen there.
|
||||
*/
|
||||
if (get_compact_nodeid() == cnode) {
|
||||
int cpu = smp_processor_id();
|
||||
LOCAL_HUB_S(PI_RT_EN_A, 1);
|
||||
LOCAL_HUB_S(PI_RT_EN_B, 1);
|
||||
LOCAL_HUB_S(PI_PROF_EN_A, 0);
|
||||
LOCAL_HUB_S(PI_PROF_EN_B, 0);
|
||||
ct_cur[cpu] = CYCLES_PER_JIFFY;
|
||||
LOCAL_HUB_S(PI_RT_COMPARE_A, ct_cur[cpu]);
|
||||
LOCAL_HUB_S(PI_RT_COUNT, 0);
|
||||
LOCAL_HUB_S(PI_RT_PEND_A, 0);
|
||||
LOCAL_HUB_S(PI_RT_COMPARE_B, ct_cur[cpu]);
|
||||
LOCAL_HUB_S(PI_RT_COUNT, 0);
|
||||
LOCAL_HUB_S(PI_RT_PEND_B, 0);
|
||||
}
|
||||
}
|
||||
|
||||
Loading…
Reference in New Issue
Block a user