mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-11 12:28:41 +08:00
dt-bindings: Add Tegra PMC pad configuration bindings
Document the PMC pinctrl bindings for pad power state and signaling voltage configuration. Both nvidia,tegra186-pmc.txt and nvidia,tegra20-pmc.txt are modified as they both cover SoC generations for which these bindings apply. Add a header defining Tegra PMC pad voltage configurations. Signed-off-by: Aapo Vienamo <avienamo@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit is contained in:
Aapo Vienamo
Thierry Reding
parent
5b394b2ddf
commit
d9be10edf7
@ -34,3 +34,96 @@ Board DTS:
|
||||
pmc@c360000 {
|
||||
nvidia,invert-interrupt;
|
||||
};
|
||||
|
||||
== Pad Control ==
|
||||
|
||||
On Tegra SoCs a pad is a set of pins which are configured as a group.
|
||||
The pin grouping is a fixed attribute of the hardware. The PMC can be
|
||||
used to set pad power state and signaling voltage. A pad can be either
|
||||
in active or power down mode. The support for power state and signaling
|
||||
voltage configuration varies depending on the pad in question. 3.3 V and
|
||||
1.8 V signaling voltages are supported on pins where software
|
||||
controllable signaling voltage switching is available.
|
||||
|
||||
Pad configurations are described with pin configuration nodes which
|
||||
are placed under the pmc node and they are referred to by the pinctrl
|
||||
client properties. For more information see
|
||||
Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
|
||||
|
||||
The following pads are present on Tegra186:
|
||||
csia csib dsi mipi-bias
|
||||
pex-clk-bias pex-clk3 pex-clk2 pex-clk1
|
||||
usb0 usb1 usb2 usb-bias
|
||||
uart audio hsic dbg
|
||||
hdmi-dp0 hdmi-dp1 pex-cntrl sdmmc2-hv
|
||||
sdmmc4 cam dsib dsic
|
||||
dsid csic csid csie
|
||||
dsif spi ufs dmic-hv
|
||||
edp sdmmc1-hv sdmmc3-hv conn
|
||||
audio-hv ao-hv
|
||||
|
||||
Required pin configuration properties:
|
||||
- pins: A list of strings, each of which contains the name of a pad
|
||||
to be configured.
|
||||
|
||||
Optional pin configuration properties:
|
||||
- low-power-enable: Configure the pad into power down mode
|
||||
- low-power-disable: Configure the pad into active mode
|
||||
- power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
|
||||
TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
|
||||
The values are defined in
|
||||
include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
|
||||
|
||||
Note: The power state can be configured on all of the above pads except
|
||||
for ao-hv. Following pads have software configurable signaling
|
||||
voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
|
||||
ao-hv.
|
||||
|
||||
Pad configuration state example:
|
||||
pmc: pmc@7000e400 {
|
||||
compatible = "nvidia,tegra186-pmc";
|
||||
reg = <0 0x0c360000 0 0x10000>,
|
||||
<0 0x0c370000 0 0x10000>,
|
||||
<0 0x0c380000 0 0x10000>,
|
||||
<0 0x0c390000 0 0x10000>;
|
||||
reg-names = "pmc", "wake", "aotag", "scratch";
|
||||
|
||||
...
|
||||
|
||||
sdmmc1_3v3: sdmmc1-3v3 {
|
||||
pins = "sdmmc1-hv";
|
||||
power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
|
||||
};
|
||||
|
||||
sdmmc1_1v8: sdmmc1-1v8 {
|
||||
pins = "sdmmc1-hv";
|
||||
power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
|
||||
};
|
||||
|
||||
hdmi_off: hdmi-off {
|
||||
pins = "hdmi";
|
||||
low-power-enable;
|
||||
}
|
||||
|
||||
hdmi_on: hdmi-on {
|
||||
pins = "hdmi";
|
||||
low-power-disable;
|
||||
}
|
||||
};
|
||||
|
||||
Pinctrl client example:
|
||||
sdmmc1: sdhci@3400000 {
|
||||
...
|
||||
pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
|
||||
pinctrl-0 = <&sdmmc1_3v3>;
|
||||
pinctrl-1 = <&sdmmc1_1v8>;
|
||||
};
|
||||
|
||||
...
|
||||
|
||||
sor0: sor@15540000 {
|
||||
...
|
||||
pinctrl-0 = <&hdmi_off>;
|
||||
pinctrl-1 = <&hdmi_on>;
|
||||
pinctrl-names = "hdmi-on", "hdmi-off";
|
||||
};
|
||||
|
||||
@ -195,3 +195,106 @@ Example:
|
||||
power-domains = <&pd_audio>;
|
||||
...
|
||||
};
|
||||
|
||||
== Pad Control ==
|
||||
|
||||
On Tegra SoCs a pad is a set of pins which are configured as a group.
|
||||
The pin grouping is a fixed attribute of the hardware. The PMC can be
|
||||
used to set pad power state and signaling voltage. A pad can be either
|
||||
in active or power down mode. The support for power state and signaling
|
||||
voltage configuration varies depending on the pad in question. 3.3 V and
|
||||
1.8 V signaling voltages are supported on pins where software
|
||||
controllable signaling voltage switching is available.
|
||||
|
||||
The pad configuration state nodes are placed under the pmc node and they
|
||||
are referred to by the pinctrl client properties. For more information
|
||||
see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
|
||||
The pad name should be used as the value of the pins property in pin
|
||||
configuration nodes.
|
||||
|
||||
The following pads are present on Tegra124 and Tegra132:
|
||||
audio bb cam comp
|
||||
csia csb cse dsi
|
||||
dsib dsic dsid hdmi
|
||||
hsic hv lvds mipi-bias
|
||||
nand pex-bias pex-clk1 pex-clk2
|
||||
pex-cntrl sdmmc1 sdmmc3 sdmmc4
|
||||
sys_ddc uart usb0 usb1
|
||||
usb2 usb_bias
|
||||
|
||||
The following pads are present on Tegra210:
|
||||
audio audio-hv cam csia
|
||||
csib csic csid csie
|
||||
csif dbg debug-nonao dmic
|
||||
dp dsi dsib dsic
|
||||
dsid emmc emmc2 gpio
|
||||
hdmi hsic lvds mipi-bias
|
||||
pex-bias pex-clk1 pex-clk2 pex-cntrl
|
||||
sdmmc1 sdmmc3 spi spi-hv
|
||||
uart usb0 usb1 usb2
|
||||
usb3 usb-bias
|
||||
|
||||
Required pin configuration properties:
|
||||
- pins: Must contain name of the pad(s) to be configured.
|
||||
|
||||
Optional pin configuration properties:
|
||||
- low-power-enable: Configure the pad into power down mode
|
||||
- low-power-disable: Configure the pad into active mode
|
||||
- power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8
|
||||
or TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
|
||||
The values are defined in
|
||||
include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
|
||||
|
||||
Note: The power state can be configured on all of the Tegra124 and
|
||||
Tegra132 pads. None of the Tegra124 or Tegra132 pads support
|
||||
signaling voltage switching.
|
||||
|
||||
Note: All of the listed Tegra210 pads except pex-cntrl support power
|
||||
state configuration. Signaling voltage switching is supported on
|
||||
following Tegra210 pads: audio, audio-hv, cam, dbg, dmic, gpio,
|
||||
pex-cntrl, sdmmc1, sdmmc3, spi, spi-hv, and uart.
|
||||
|
||||
Pad configuration state example:
|
||||
pmc: pmc@7000e400 {
|
||||
compatible = "nvidia,tegra210-pmc";
|
||||
reg = <0x0 0x7000e400 0x0 0x400>;
|
||||
clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
|
||||
clock-names = "pclk", "clk32k_in";
|
||||
|
||||
...
|
||||
|
||||
sdmmc1_3v3: sdmmc1-3v3 {
|
||||
pins = "sdmmc1";
|
||||
power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
|
||||
};
|
||||
|
||||
sdmmc1_1v8: sdmmc1-1v8 {
|
||||
pins = "sdmmc1";
|
||||
power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
|
||||
};
|
||||
|
||||
hdmi_off: hdmi-off {
|
||||
pins = "hdmi";
|
||||
low-power-enable;
|
||||
}
|
||||
|
||||
hdmi_on: hdmi-on {
|
||||
pins = "hdmi";
|
||||
low-power-disable;
|
||||
}
|
||||
};
|
||||
|
||||
Pinctrl client example:
|
||||
sdmmc1: sdhci@700b0000 {
|
||||
...
|
||||
pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
|
||||
pinctrl-0 = <&sdmmc1_3v3>;
|
||||
pinctrl-1 = <&sdmmc1_1v8>;
|
||||
};
|
||||
...
|
||||
sor@54540000 {
|
||||
...
|
||||
pinctrl-0 = <&hdmi_off>;
|
||||
pinctrl-1 = <&hdmi_on>;
|
||||
pinctrl-names = "hdmi-on", "hdmi-off";
|
||||
};
|
||||
|
||||
18
include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
Normal file
18
include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
Normal file
@ -0,0 +1,18 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0 */
|
||||
/*
|
||||
* pinctrl-tegra-io-pad.h: Tegra I/O pad source voltage configuration constants
|
||||
* pinctrl bindings.
|
||||
*
|
||||
* Copyright (c) 2018, NVIDIA CORPORATION. All rights reserved.
|
||||
*
|
||||
* Author: Aapo Vienamo <avienamo@nvidia.com>
|
||||
*/
|
||||
|
||||
#ifndef _DT_BINDINGS_PINCTRL_TEGRA_IO_PAD_H
|
||||
#define _DT_BINDINGS_PINCTRL_TEGRA_IO_PAD_H
|
||||
|
||||
/* Voltage levels of the I/O pad's source rail */
|
||||
#define TEGRA_IO_PAD_VOLTAGE_1V8 0
|
||||
#define TEGRA_IO_PAD_VOLTAGE_3V3 1
|
||||
|
||||
#endif
|
||||
Loading…
Reference in New Issue
Block a user