From 800d595151bbd8b42667c69d62af793290454817 Mon Sep 17 00:00:00 2001 From: Stefan Riedmueller Date: Tue, 9 Jan 2018 17:09:56 +0100 Subject: [PATCH] ARM: dts: imx6: Add initial support for phyBOARD-Mira This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board for PHYTEC phyCORE-i.MX 6. Signed-off-by: Christian Hemp Signed-off-by: Stefan Christ Signed-off-by: Christoph Fritz Signed-off-by: Stefan Riedmueller Reviewed-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 +++++++++++++++++++++ 1 file changed, 390 insertions(+) create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi new file mode 100644 index 000000000000..9ebd438dce7d --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi @@ -0,0 +1,390 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2018 PHYTEC Messtechnik GmbH + * Author: Christian Hemp + */ + + +/ { + aliases { + rtc0 = &i2c_rtc; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_backlight>; + pwms = <&pwm1 0 5000000>; + status = "okay"; + }; + + gpio_leds: leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpioleds>; + status = "disabled"; + + red { + label = "phyboard-mira:red"; + gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; + }; + + green { + label = "phyboard-mira:green"; + gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>; + }; + + blue { + label = "phyboard-mira:blue"; + gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + }; + }; + + reg_backlight: regulator-backlight { + compatible = "regulator-fixed"; + regulator-name = "backlight_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_en_switch: regulator-en-switch { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_en_switch>; + regulator-name = "Enable Switch"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>; + regulator-always-on; + }; + + reg_flexcan1: regulator-flexcan1 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1_en>; + regulator-name = "flexcan1-reg"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_panel: regulator-panel { + compatible = "regulator-fixed"; + regulator-name = "panel-power-supply"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + reg_pcie: regulator-pcie { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie_reg>; + regulator-name = "mPCIe_1V5"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + gpio = <&gpio3 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_h1_vbus: usb-h1-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_vbus>; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio2 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usbotg_vbus: usbotg-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_vbus>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + panel { + compatible = "auo,g104sn02"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_panel_en>; + power-supply = <®_panel>; + enable-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; + backlight = <&backlight>; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_flexcan1>; + status = "disabled"; +}; + +&hdmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hdmicec>; + ddc-i2c-bus = <&i2c2>; + status = "disabled"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clock-frequency = <400000>; + status = "disabled"; + + stmpe: touchctrl@44 { + compatible = "st,stmpe811"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_stmpe>; + reg = <0x44>; + interrupt-parent = <&gpio7>; + interrupts = <12 IRQ_TYPE_NONE>; + status = "disabled"; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; + }; + + i2c_rtc: rtc@68 { + compatible = "microcrystal,rv4162"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc_int>; + reg = <0x68>; + interrupt-parent = <&gpio7>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <100000>; + status = "disabled"; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + status = "disabled"; + + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio2 25 GPIO_ACTIVE_LOW>; + vpcie-supply = <®_pcie>; + status = "disabled"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + uart-has-rtscts; + status = "disabled"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + disable-over-current; + status = "disabled"; +}; + +&usbotg { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + vbus-supply = <®_usbotg_vbus>; + disable-over-current; + status = "disabled"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>; + no-1-8-v; + status = "disabled"; +}; + +&iomuxc { + pinctrl_panel_en: panelen1grp { + fsl,pins = < + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0xb0b1 + >; + }; + + pinctrl_en_switch: enswitchgrp { + fsl,pins = < + MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0xb0b1 + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0 + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0 + >; + }; + + pinctrl_flexcan1_en: flexcan1engrp { + fsl,pins = < + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0xb0b1 + >; + }; + + pinctrl_gpioleds: gpioledsgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0 + MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0 + MX6QDL_PAD_CSI0_DAT6__GPIO5_IO24 0x1b0b0 + >; + }; + + pinctrl_hdmicec: hdmicecgrp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_pcie: pciegrp { + fsl,pins = < + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0xb0b1 + >; + }; + + pinctrl_pcie_reg: pciereggrp { + fsl,pins = < + MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0xb0b1 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_rtc_int: rtcintgrp { + fsl,pins = < + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0 + >; + }; + + pinctrl_stmpe: stmpegrp { + fsl,pins = < + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_EB3__UART3_CTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D23__UART3_RTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbh1_vbus: usbh1vbusgrp { + fsl,pins = < + MX6QDL_PAD_EIM_A20__GPIO2_IO18 0xb0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usbotg_vbus: usbotgvbusgrp { + fsl,pins = < + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0xb0b1 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb0b1 /* CD */ + >; + }; +};