mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-08 19:44:10 +08:00
docs: networking: device drivers: convert neterion/s2io.txt to ReST
- add SPDX header; - add a document title; - comment out text-only TOC from html/pdf output; - mark code blocks and literals as such; - adjust identation, whitespaces and blank lines where needed; - add to networking/index.rst. Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
Mauro Carvalho Chehab
David S. Miller
parent
011531f7e5
commit
7762f5c514
@ -42,6 +42,7 @@ Contents:
|
||||
intel/ipw2100
|
||||
intel/ipw2200
|
||||
microsoft/netvsc
|
||||
neterion/s2io
|
||||
|
||||
.. only:: subproject and html
|
||||
|
||||
|
||||
196
Documentation/networking/device_drivers/neterion/s2io.rst
Normal file
196
Documentation/networking/device_drivers/neterion/s2io.rst
Normal file
@ -0,0 +1,196 @@
|
||||
.. SPDX-License-Identifier: GPL-2.0
|
||||
|
||||
=========================================================
|
||||
Neterion's (Formerly S2io) Xframe I/II PCI-X 10GbE driver
|
||||
=========================================================
|
||||
|
||||
Release notes for Neterion's (Formerly S2io) Xframe I/II PCI-X 10GbE driver.
|
||||
|
||||
.. Contents
|
||||
- 1. Introduction
|
||||
- 2. Identifying the adapter/interface
|
||||
- 3. Features supported
|
||||
- 4. Command line parameters
|
||||
- 5. Performance suggestions
|
||||
- 6. Available Downloads
|
||||
|
||||
|
||||
1. Introduction
|
||||
===============
|
||||
This Linux driver supports Neterion's Xframe I PCI-X 1.0 and
|
||||
Xframe II PCI-X 2.0 adapters. It supports several features
|
||||
such as jumbo frames, MSI/MSI-X, checksum offloads, TSO, UFO and so on.
|
||||
See below for complete list of features.
|
||||
|
||||
All features are supported for both IPv4 and IPv6.
|
||||
|
||||
2. Identifying the adapter/interface
|
||||
====================================
|
||||
|
||||
a. Insert the adapter(s) in your system.
|
||||
b. Build and load driver::
|
||||
|
||||
# insmod s2io.ko
|
||||
|
||||
c. View log messages::
|
||||
|
||||
# dmesg | tail -40
|
||||
|
||||
You will see messages similar to::
|
||||
|
||||
eth3: Neterion Xframe I 10GbE adapter (rev 3), Version 2.0.9.1, Intr type INTA
|
||||
eth4: Neterion Xframe II 10GbE adapter (rev 2), Version 2.0.9.1, Intr type INTA
|
||||
eth4: Device is on 64 bit 133MHz PCIX(M1) bus
|
||||
|
||||
The above messages identify the adapter type(Xframe I/II), adapter revision,
|
||||
driver version, interface name(eth3, eth4), Interrupt type(INTA, MSI, MSI-X).
|
||||
In case of Xframe II, the PCI/PCI-X bus width and frequency are displayed
|
||||
as well.
|
||||
|
||||
To associate an interface with a physical adapter use "ethtool -p <ethX>".
|
||||
The corresponding adapter's LED will blink multiple times.
|
||||
|
||||
3. Features supported
|
||||
=====================
|
||||
a. Jumbo frames. Xframe I/II supports MTU up to 9600 bytes,
|
||||
modifiable using ip command.
|
||||
|
||||
b. Offloads. Supports checksum offload(TCP/UDP/IP) on transmit
|
||||
and receive, TSO.
|
||||
|
||||
c. Multi-buffer receive mode. Scattering of packet across multiple
|
||||
buffers. Currently driver supports 2-buffer mode which yields
|
||||
significant performance improvement on certain platforms(SGI Altix,
|
||||
IBM xSeries).
|
||||
|
||||
d. MSI/MSI-X. Can be enabled on platforms which support this feature
|
||||
(IA64, Xeon) resulting in noticeable performance improvement(up to 7%
|
||||
on certain platforms).
|
||||
|
||||
e. Statistics. Comprehensive MAC-level and software statistics displayed
|
||||
using "ethtool -S" option.
|
||||
|
||||
f. Multi-FIFO/Ring. Supports up to 8 transmit queues and receive rings,
|
||||
with multiple steering options.
|
||||
|
||||
4. Command line parameters
|
||||
==========================
|
||||
|
||||
a. tx_fifo_num
|
||||
Number of transmit queues
|
||||
|
||||
Valid range: 1-8
|
||||
|
||||
Default: 1
|
||||
|
||||
b. rx_ring_num
|
||||
Number of receive rings
|
||||
|
||||
Valid range: 1-8
|
||||
|
||||
Default: 1
|
||||
|
||||
c. tx_fifo_len
|
||||
Size of each transmit queue
|
||||
|
||||
Valid range: Total length of all queues should not exceed 8192
|
||||
|
||||
Default: 4096
|
||||
|
||||
d. rx_ring_sz
|
||||
Size of each receive ring(in 4K blocks)
|
||||
|
||||
Valid range: Limited by memory on system
|
||||
|
||||
Default: 30
|
||||
|
||||
e. intr_type
|
||||
Specifies interrupt type. Possible values 0(INTA), 2(MSI-X)
|
||||
|
||||
Valid values: 0, 2
|
||||
|
||||
Default: 2
|
||||
|
||||
5. Performance suggestions
|
||||
==========================
|
||||
|
||||
General:
|
||||
|
||||
a. Set MTU to maximum(9000 for switch setup, 9600 in back-to-back configuration)
|
||||
b. Set TCP windows size to optimal value.
|
||||
|
||||
For instance, for MTU=1500 a value of 210K has been observed to result in
|
||||
good performance::
|
||||
|
||||
# sysctl -w net.ipv4.tcp_rmem="210000 210000 210000"
|
||||
# sysctl -w net.ipv4.tcp_wmem="210000 210000 210000"
|
||||
|
||||
For MTU=9000, TCP window size of 10 MB is recommended::
|
||||
|
||||
# sysctl -w net.ipv4.tcp_rmem="10000000 10000000 10000000"
|
||||
# sysctl -w net.ipv4.tcp_wmem="10000000 10000000 10000000"
|
||||
|
||||
Transmit performance:
|
||||
|
||||
a. By default, the driver respects BIOS settings for PCI bus parameters.
|
||||
However, you may want to experiment with PCI bus parameters
|
||||
max-split-transactions(MOST) and MMRBC (use setpci command).
|
||||
|
||||
A MOST value of 2 has been found optimal for Opterons and 3 for Itanium.
|
||||
|
||||
It could be different for your hardware.
|
||||
|
||||
Set MMRBC to 4K**.
|
||||
|
||||
For example you can set
|
||||
|
||||
For opteron::
|
||||
|
||||
#setpci -d 17d5:* 62=1d
|
||||
|
||||
For Itanium::
|
||||
|
||||
#setpci -d 17d5:* 62=3d
|
||||
|
||||
For detailed description of the PCI registers, please see Xframe User Guide.
|
||||
|
||||
b. Ensure Transmit Checksum offload is enabled. Use ethtool to set/verify this
|
||||
parameter.
|
||||
|
||||
c. Turn on TSO(using "ethtool -K")::
|
||||
|
||||
# ethtool -K <ethX> tso on
|
||||
|
||||
Receive performance:
|
||||
|
||||
a. By default, the driver respects BIOS settings for PCI bus parameters.
|
||||
However, you may want to set PCI latency timer to 248::
|
||||
|
||||
#setpci -d 17d5:* LATENCY_TIMER=f8
|
||||
|
||||
For detailed description of the PCI registers, please see Xframe User Guide.
|
||||
|
||||
b. Use 2-buffer mode. This results in large performance boost on
|
||||
certain platforms(eg. SGI Altix, IBM xSeries).
|
||||
|
||||
c. Ensure Receive Checksum offload is enabled. Use "ethtool -K ethX" command to
|
||||
set/verify this option.
|
||||
|
||||
d. Enable NAPI feature(in kernel configuration Device Drivers ---> Network
|
||||
device support ---> Ethernet (10000 Mbit) ---> S2IO 10Gbe Xframe NIC) to
|
||||
bring down CPU utilization.
|
||||
|
||||
.. note::
|
||||
|
||||
For AMD opteron platforms with 8131 chipset, MMRBC=1 and MOST=1 are
|
||||
recommended as safe parameters.
|
||||
|
||||
For more information, please review the AMD8131 errata at
|
||||
http://vip.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/
|
||||
26310_AMD-8131_HyperTransport_PCI-X_Tunnel_Revision_Guide_rev_3_18.pdf
|
||||
|
||||
6. Support
|
||||
==========
|
||||
|
||||
For further support please contact either your 10GbE Xframe NIC vendor (IBM,
|
||||
HP, SGI etc.)
|
||||
@ -1,141 +0,0 @@
|
||||
Release notes for Neterion's (Formerly S2io) Xframe I/II PCI-X 10GbE driver.
|
||||
|
||||
Contents
|
||||
=======
|
||||
- 1. Introduction
|
||||
- 2. Identifying the adapter/interface
|
||||
- 3. Features supported
|
||||
- 4. Command line parameters
|
||||
- 5. Performance suggestions
|
||||
- 6. Available Downloads
|
||||
|
||||
|
||||
1. Introduction:
|
||||
This Linux driver supports Neterion's Xframe I PCI-X 1.0 and
|
||||
Xframe II PCI-X 2.0 adapters. It supports several features
|
||||
such as jumbo frames, MSI/MSI-X, checksum offloads, TSO, UFO and so on.
|
||||
See below for complete list of features.
|
||||
All features are supported for both IPv4 and IPv6.
|
||||
|
||||
2. Identifying the adapter/interface:
|
||||
a. Insert the adapter(s) in your system.
|
||||
b. Build and load driver
|
||||
# insmod s2io.ko
|
||||
c. View log messages
|
||||
# dmesg | tail -40
|
||||
You will see messages similar to:
|
||||
eth3: Neterion Xframe I 10GbE adapter (rev 3), Version 2.0.9.1, Intr type INTA
|
||||
eth4: Neterion Xframe II 10GbE adapter (rev 2), Version 2.0.9.1, Intr type INTA
|
||||
eth4: Device is on 64 bit 133MHz PCIX(M1) bus
|
||||
|
||||
The above messages identify the adapter type(Xframe I/II), adapter revision,
|
||||
driver version, interface name(eth3, eth4), Interrupt type(INTA, MSI, MSI-X).
|
||||
In case of Xframe II, the PCI/PCI-X bus width and frequency are displayed
|
||||
as well.
|
||||
|
||||
To associate an interface with a physical adapter use "ethtool -p <ethX>".
|
||||
The corresponding adapter's LED will blink multiple times.
|
||||
|
||||
3. Features supported:
|
||||
a. Jumbo frames. Xframe I/II supports MTU up to 9600 bytes,
|
||||
modifiable using ip command.
|
||||
|
||||
b. Offloads. Supports checksum offload(TCP/UDP/IP) on transmit
|
||||
and receive, TSO.
|
||||
|
||||
c. Multi-buffer receive mode. Scattering of packet across multiple
|
||||
buffers. Currently driver supports 2-buffer mode which yields
|
||||
significant performance improvement on certain platforms(SGI Altix,
|
||||
IBM xSeries).
|
||||
|
||||
d. MSI/MSI-X. Can be enabled on platforms which support this feature
|
||||
(IA64, Xeon) resulting in noticeable performance improvement(up to 7%
|
||||
on certain platforms).
|
||||
|
||||
e. Statistics. Comprehensive MAC-level and software statistics displayed
|
||||
using "ethtool -S" option.
|
||||
|
||||
f. Multi-FIFO/Ring. Supports up to 8 transmit queues and receive rings,
|
||||
with multiple steering options.
|
||||
|
||||
4. Command line parameters
|
||||
a. tx_fifo_num
|
||||
Number of transmit queues
|
||||
Valid range: 1-8
|
||||
Default: 1
|
||||
|
||||
b. rx_ring_num
|
||||
Number of receive rings
|
||||
Valid range: 1-8
|
||||
Default: 1
|
||||
|
||||
c. tx_fifo_len
|
||||
Size of each transmit queue
|
||||
Valid range: Total length of all queues should not exceed 8192
|
||||
Default: 4096
|
||||
|
||||
d. rx_ring_sz
|
||||
Size of each receive ring(in 4K blocks)
|
||||
Valid range: Limited by memory on system
|
||||
Default: 30
|
||||
|
||||
e. intr_type
|
||||
Specifies interrupt type. Possible values 0(INTA), 2(MSI-X)
|
||||
Valid values: 0, 2
|
||||
Default: 2
|
||||
|
||||
5. Performance suggestions
|
||||
General:
|
||||
a. Set MTU to maximum(9000 for switch setup, 9600 in back-to-back configuration)
|
||||
b. Set TCP windows size to optimal value.
|
||||
For instance, for MTU=1500 a value of 210K has been observed to result in
|
||||
good performance.
|
||||
# sysctl -w net.ipv4.tcp_rmem="210000 210000 210000"
|
||||
# sysctl -w net.ipv4.tcp_wmem="210000 210000 210000"
|
||||
For MTU=9000, TCP window size of 10 MB is recommended.
|
||||
# sysctl -w net.ipv4.tcp_rmem="10000000 10000000 10000000"
|
||||
# sysctl -w net.ipv4.tcp_wmem="10000000 10000000 10000000"
|
||||
|
||||
Transmit performance:
|
||||
a. By default, the driver respects BIOS settings for PCI bus parameters.
|
||||
However, you may want to experiment with PCI bus parameters
|
||||
max-split-transactions(MOST) and MMRBC (use setpci command).
|
||||
A MOST value of 2 has been found optimal for Opterons and 3 for Itanium.
|
||||
It could be different for your hardware.
|
||||
Set MMRBC to 4K**.
|
||||
|
||||
For example you can set
|
||||
For opteron
|
||||
#setpci -d 17d5:* 62=1d
|
||||
For Itanium
|
||||
#setpci -d 17d5:* 62=3d
|
||||
|
||||
For detailed description of the PCI registers, please see Xframe User Guide.
|
||||
|
||||
b. Ensure Transmit Checksum offload is enabled. Use ethtool to set/verify this
|
||||
parameter.
|
||||
c. Turn on TSO(using "ethtool -K")
|
||||
# ethtool -K <ethX> tso on
|
||||
|
||||
Receive performance:
|
||||
a. By default, the driver respects BIOS settings for PCI bus parameters.
|
||||
However, you may want to set PCI latency timer to 248.
|
||||
#setpci -d 17d5:* LATENCY_TIMER=f8
|
||||
For detailed description of the PCI registers, please see Xframe User Guide.
|
||||
b. Use 2-buffer mode. This results in large performance boost on
|
||||
certain platforms(eg. SGI Altix, IBM xSeries).
|
||||
c. Ensure Receive Checksum offload is enabled. Use "ethtool -K ethX" command to
|
||||
set/verify this option.
|
||||
d. Enable NAPI feature(in kernel configuration Device Drivers ---> Network
|
||||
device support ---> Ethernet (10000 Mbit) ---> S2IO 10Gbe Xframe NIC) to
|
||||
bring down CPU utilization.
|
||||
|
||||
** For AMD opteron platforms with 8131 chipset, MMRBC=1 and MOST=1 are
|
||||
recommended as safe parameters.
|
||||
For more information, please review the AMD8131 errata at
|
||||
http://vip.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/
|
||||
26310_AMD-8131_HyperTransport_PCI-X_Tunnel_Revision_Guide_rev_3_18.pdf
|
||||
|
||||
6. Support
|
||||
For further support please contact either your 10GbE Xframe NIC vendor (IBM,
|
||||
HP, SGI etc.)
|
||||
@ -11656,7 +11656,7 @@ NETERION 10GbE DRIVERS (s2io/vxge)
|
||||
M: Jon Mason <jdmason@kudzu.us>
|
||||
L: netdev@vger.kernel.org
|
||||
S: Supported
|
||||
F: Documentation/networking/device_drivers/neterion/s2io.txt
|
||||
F: Documentation/networking/device_drivers/neterion/s2io.rst
|
||||
F: Documentation/networking/device_drivers/neterion/vxge.txt
|
||||
F: drivers/net/ethernet/neterion/
|
||||
|
||||
|
||||
@ -27,7 +27,7 @@ config S2IO
|
||||
on its age.
|
||||
|
||||
More specific information on configuring the driver is in
|
||||
<file:Documentation/networking/device_drivers/neterion/s2io.txt>.
|
||||
<file:Documentation/networking/device_drivers/neterion/s2io.rst>.
|
||||
|
||||
To compile this driver as a module, choose M here. The module
|
||||
will be called s2io.
|
||||
|
||||
Loading…
Reference in New Issue
Block a user