Documentation: spi: Update documentation for renaming "master" to "controller"

In commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
some functions and struct members were renamed. Adapt the documentation
accordingly.

Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/3d643e22cacff12d3918ad5224baa1d01813d03b.1707324794.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit is contained in:
Uwe Kleine-König 2024-02-07 19:40:46 +01:00 committed by Mark Brown
parent 620d269f29
commit 76b31eb4c2
No known key found for this signature in database
GPG Key ID: 24D68B725D5487D0

View File

@ -9,7 +9,7 @@ What is SPI?
The "Serial Peripheral Interface" (SPI) is a synchronous four wire serial
link used to connect microcontrollers to sensors, memory, and peripherals.
It's a simple "de facto" standard, not complicated enough to acquire a
standardization body. SPI uses a master/slave configuration.
standardization body. SPI uses a host/target configuration.
The three signal wires hold a clock (SCK, often on the order of 10 MHz),
and parallel data lines with "Master Out, Slave In" (MOSI) or "Master In,
@ -19,11 +19,11 @@ commonly used. Each clock cycle shifts data out and data in; the clock
doesn't cycle except when there is a data bit to shift. Not all data bits
are used though; not every protocol uses those full duplex capabilities.
SPI masters use a fourth "chip select" line to activate a given SPI slave
SPI hosts use a fourth "chip select" line to activate a given SPI slave
device, so those three signal wires may be connected to several chips
in parallel. All SPI slaves support chipselects; they are usually active
low signals, labeled nCSx for slave 'x' (e.g. nCS0). Some devices have
other signals, often including an interrupt to the master.
other signals, often including an interrupt to the host.
Unlike serial busses like USB or SMBus, even low level protocols for
SPI slave functions are usually not interoperable between vendors
@ -45,8 +45,8 @@ SPI slave functions are usually not interoperable between vendors
In the same way, SPI slaves will only rarely support any kind of automatic
discovery/enumeration protocol. The tree of slave devices accessible from
a given SPI master will normally be set up manually, with configuration
tables.
a given SPI host controller will normally be set up manually, with
configuration tables.
SPI is only one of the names used by such four-wire protocols, and
most controllers have no problem handling "MicroWire" (think of it as
@ -62,8 +62,8 @@ course they won't handle full duplex transfers. You may find such
chips described as using "three wire" signaling: SCK, data, nCSx.
(That data line is sometimes called MOMI or SISO.)
Microcontrollers often support both master and slave sides of the SPI
protocol. This document (and Linux) supports both the master and slave
Microcontrollers often support both host and target sides of the SPI
protocol. This document (and Linux) supports both the host and target
sides of SPI interactions.
@ -118,7 +118,7 @@ starting low (CPOL=0) and data stabilized for sampling during the
trailing clock edge (CPHA=1), that's SPI mode 1.
Note that the clock mode is relevant as soon as the chipselect goes
active. So the master must set the clock to inactive before selecting
active. So the host must set the clock to inactive before selecting
a slave, and the slave can tell the chosen polarity by sampling the
clock level when its select line goes active. That's why many devices
support for example both modes 0 and 3: they don't care about polarity,
@ -179,7 +179,7 @@ shows up in sysfs in several locations::
/sys/bus/spi/drivers/D ... driver for one or more spi*.* devices
/sys/class/spi_master/spiB ... symlink to a logical node which could hold
class related state for the SPI master controller managing bus "B".
class related state for the SPI host controller managing bus "B".
All spiB.* devices share one physical SPI bus segment, with SCLK,
MOSI, and MISO.
@ -316,7 +316,7 @@ sharing a bus with a device that interprets chipselect "backwards" is
not possible until the infrastructure knows how to deselect it.
Then your board initialization code would register that table with the SPI
infrastructure, so that it's available later when the SPI master controller
infrastructure, so that it's available later when the SPI host controller
driver is registered::
spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
@ -474,34 +474,34 @@ How do I write an "SPI Master Controller Driver"?
An SPI controller will probably be registered on the platform_bus; write
a driver to bind to the device, whichever bus is involved.
The main task of this type of driver is to provide an "spi_master".
Use spi_alloc_master() to allocate the master, and spi_master_get_devdata()
to get the driver-private data allocated for that device.
The main task of this type of driver is to provide an "spi_controller".
Use spi_alloc_host() to allocate the host controller, and
spi_controller_get_devdata() to get the driver-private data allocated for that
device.
::
struct spi_master *master;
struct spi_controller *ctlr;
struct CONTROLLER *c;
master = spi_alloc_master(dev, sizeof *c);
if (!master)
ctlr = spi_alloc_host(dev, sizeof *c);
if (!ctlr)
return -ENODEV;
c = spi_master_get_devdata(master);
c = spi_controller_get_devdata(ctlr);
The driver will initialize the fields of that spi_master, including the
bus number (maybe the same as the platform device ID) and three methods
used to interact with the SPI core and SPI protocol drivers. It will
also initialize its own internal state. (See below about bus numbering
and those methods.)
The driver will initialize the fields of that spi_controller, including the bus
number (maybe the same as the platform device ID) and three methods used to
interact with the SPI core and SPI protocol drivers. It will also initialize
its own internal state. (See below about bus numbering and those methods.)
After you initialize the spi_master, then use spi_register_master() to
After you initialize the spi_controller, then use spi_register_controller() to
publish it to the rest of the system. At that time, device nodes for the
controller and any predeclared spi devices will be made available, and
the driver model core will take care of binding them to drivers.
If you need to remove your SPI controller driver, spi_unregister_master()
will reverse the effect of spi_register_master().
If you need to remove your SPI controller driver, spi_unregister_controller()
will reverse the effect of spi_register_controller().
Bus Numbering
@ -519,10 +519,10 @@ then be replaced by a dynamically assigned number. You'd then need to treat
this as a non-static configuration (see above).
SPI Master Methods
^^^^^^^^^^^^^^^^^^
SPI Host Controller Methods
^^^^^^^^^^^^^^^^^^^^^^^^^^^
``master->setup(struct spi_device *spi)``
``ctlr->setup(struct spi_device *spi)``
This sets up the device clock rate, SPI mode, and word sizes.
Drivers may change the defaults provided by board_info, and then
call spi_setup(spi) to invoke this routine. It may sleep.
@ -534,34 +534,34 @@ SPI Master Methods
.. note::
BUG ALERT: for some reason the first version of
many spi_master drivers seems to get this wrong.
many spi_controller drivers seems to get this wrong.
When you code setup(), ASSUME that the controller
is actively processing transfers for another device.
``master->cleanup(struct spi_device *spi)``
``ctlr->cleanup(struct spi_device *spi)``
Your controller driver may use spi_device.controller_state to hold
state it dynamically associates with that device. If you do that,
be sure to provide the cleanup() method to free that state.
``master->prepare_transfer_hardware(struct spi_master *master)``
``ctlr->prepare_transfer_hardware(struct spi_controller *ctlr)``
This will be called by the queue mechanism to signal to the driver
that a message is coming in soon, so the subsystem requests the
driver to prepare the transfer hardware by issuing this call.
This may sleep.
``master->unprepare_transfer_hardware(struct spi_master *master)``
``ctlr->unprepare_transfer_hardware(struct spi_controller *ctlr)``
This will be called by the queue mechanism to signal to the driver
that there are no more messages pending in the queue and it may
relax the hardware (e.g. by power management calls). This may sleep.
``master->transfer_one_message(struct spi_master *master, struct spi_message *mesg)``
``ctlr->transfer_one_message(struct spi_controller *ctlr, struct spi_message *mesg)``
The subsystem calls the driver to transfer a single message while
queuing transfers that arrive in the meantime. When the driver is
finished with this message, it must call
spi_finalize_current_message() so the subsystem can issue the next
message. This may sleep.
``master->transfer_one(struct spi_master *master, struct spi_device *spi, struct spi_transfer *transfer)``
``ctrl->transfer_one(struct spi_controller *ctlr, struct spi_device *spi, struct spi_transfer *transfer)``
The subsystem calls the driver to transfer a single transfer while
queuing transfers that arrive in the meantime. When the driver is
finished with this transfer, it must call
@ -576,15 +576,15 @@ SPI Master Methods
* 0: transfer is finished
* 1: transfer is still in progress
``master->set_cs_timing(struct spi_device *spi, u8 setup_clk_cycles, u8 hold_clk_cycles, u8 inactive_clk_cycles)``
This method allows SPI client drivers to request SPI master controller
``ctrl->set_cs_timing(struct spi_device *spi, u8 setup_clk_cycles, u8 hold_clk_cycles, u8 inactive_clk_cycles)``
This method allows SPI client drivers to request SPI host controller
for configuring device specific CS setup, hold and inactive timing
requirements.
Deprecated Methods
^^^^^^^^^^^^^^^^^^
``master->transfer(struct spi_device *spi, struct spi_message *message)``
``ctrl->transfer(struct spi_device *spi, struct spi_message *message)``
This must not sleep. Its responsibility is to arrange that the
transfer happens and its complete() callback is issued. The two
will normally happen later, after other transfers complete, and