From 75d11676dccb643de1e850c8a29f5e9aa58157c0 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Mon, 17 Dec 2018 12:04:43 +0800 Subject: [PATCH] Bluetooth: hci_bcm: Add support for regulator supplies The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO. The former provides overall power for the chip, while the latter powers the I/O pins and buffers. Model these two as regulator supplies, and let the driver manage them in the same way as it does the clock supply. Tested-by: Ondrej Jirman Signed-off-by: Chen-Yu Tsai Signed-off-by: Marcel Holtmann --- drivers/bluetooth/hci_bcm.c | 39 ++++++++++++++++++++++++++++--------- 1 file changed, 30 insertions(+), 9 deletions(-) diff --git a/drivers/bluetooth/hci_bcm.c b/drivers/bluetooth/hci_bcm.c index 345d728a5434..f2101038284e 100644 --- a/drivers/bluetooth/hci_bcm.c +++ b/drivers/bluetooth/hci_bcm.c @@ -31,6 +31,7 @@ #include #include #include +#include #include #include #include @@ -53,6 +54,8 @@ #define BCM_AUTOSUSPEND_DELAY 5000 /* default autosleep delay */ +#define BCM_NUM_SUPPLIES 2 + /** * struct bcm_device - device driver resources * @serdev_hu: HCI UART controller struct @@ -73,7 +76,8 @@ * @btpd: Apple ACPI method to drive BT_REG_ON pin low ("Bluetooth Power Down") * @txco_clk: external reference frequency clock used by Bluetooth device * @lpo_clk: external LPO clock used by Bluetooth device - * @clk_enabled: whether clocks are prepared and enabled + * @supplies: VBAT and VDDIO supplies used by Bluetooth device + * @res_enabled: whether clocks and supplies are prepared and enabled * @init_speed: default baudrate of Bluetooth device; * the host UART is initially set to this baudrate so that * it can configure the Bluetooth device for @oper_speed @@ -105,7 +109,8 @@ struct bcm_device { struct clk *txco_clk; struct clk *lpo_clk; - bool clk_enabled; + struct regulator_bulk_data supplies[BCM_NUM_SUPPLIES]; + bool res_enabled; u32 init_speed; u32 oper_speed; @@ -216,17 +221,21 @@ static int bcm_gpio_set_power(struct bcm_device *dev, bool powered) { int err; - if (powered && !dev->clk_enabled) { + if (powered && !dev->res_enabled) { + err = regulator_bulk_enable(BCM_NUM_SUPPLIES, dev->supplies); + if (err) + return err; + /* LPO clock needs to be 32.768 kHz */ err = clk_set_rate(dev->lpo_clk, 32768); if (err) { dev_err(dev->dev, "Could not set LPO clock rate\n"); - return err; + goto err_regulator_disable; } err = clk_prepare_enable(dev->lpo_clk); if (err) - return err; + goto err_regulator_disable; err = clk_prepare_enable(dev->txco_clk); if (err) @@ -241,23 +250,27 @@ static int bcm_gpio_set_power(struct bcm_device *dev, bool powered) if (err) goto err_revert_shutdown; - if (!powered && dev->clk_enabled) { + if (!powered && dev->res_enabled) { clk_disable_unprepare(dev->txco_clk); clk_disable_unprepare(dev->lpo_clk); + regulator_bulk_disable(BCM_NUM_SUPPLIES, dev->supplies); } - dev->clk_enabled = powered; + dev->res_enabled = powered; return 0; err_revert_shutdown: dev->set_shutdown(dev, !powered); err_txco_clk_disable: - if (powered && !dev->clk_enabled) + if (powered && !dev->res_enabled) clk_disable_unprepare(dev->txco_clk); err_lpo_clk_disable: - if (powered && !dev->clk_enabled) + if (powered && !dev->res_enabled) clk_disable_unprepare(dev->lpo_clk); +err_regulator_disable: + if (powered && !dev->res_enabled) + regulator_bulk_disable(BCM_NUM_SUPPLIES, dev->supplies); return err; } @@ -936,6 +949,7 @@ static struct clk *bcm_get_txco(struct device *dev) static int bcm_get_resources(struct bcm_device *dev) { const struct dmi_system_id *dmi_id; + int err; dev->name = dev_name(dev->dev); @@ -978,6 +992,13 @@ static int bcm_get_resources(struct bcm_device *dev) dev->set_device_wakeup = bcm_gpio_set_device_wakeup; dev->set_shutdown = bcm_gpio_set_shutdown; + dev->supplies[0].supply = "vbat"; + dev->supplies[1].supply = "vddio"; + err = devm_regulator_bulk_get(dev->dev, BCM_NUM_SUPPLIES, + dev->supplies); + if (err) + return err; + /* IRQ can be declared in ACPI table as Interrupt or GpioInt */ if (dev->irq <= 0) { struct gpio_desc *gpio;