Merge branch '3.15/dss-dt-dts' into 3.15/fbdev

OMAP DSS related .dts changes

Documentation/devicetree/bindings/arm/omap/dmm.txt

@@ -0,0 +1,22 @@
+OMAP Dynamic Memory Manager (DMM) bindings
+
+The dynamic memory manager (DMM) is a module located immediately in front of the
+SDRAM controllers (called EMIFs on OMAP). DMM manages various aspects of memory
+accesses such as priority generation amongst initiators, configuration of SDRAM
+interleaving, optimizing transfer of 2D block objects, and provide MMU-like page
+translation for initiators which need contiguous dma bus addresses.
+
+Required properties:
+- compatible:	Should contain "ti,omap4-dmm" for OMAP4 family
+		Should contain "ti,omap5-dmm" for OMAP5 and DRA7x family
+- reg:		Contains DMM register address range (base address and length)
+- interrupts:	Should contain an interrupt-specifier for DMM_IRQ.
+- ti,hwmods:	Name of the hwmod associated to DMM, which is typically "dmm"
+
+Example:
+
+dmm@4e000000 {
+	compatible = "ti,omap4-dmm";
+	reg = <0x4e000000 0x800>;
+	ti,hwmods = "dmm";
+};

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -99,6 +99,9 @@ Boards:
 - OMAP4 PandaBoard : Low cost community board
   compatible = "ti,omap4-panda", "ti,omap4430"
 
+- OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board
+  compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
+
 - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x
   compatible = "ti,omap3-evm", "ti,omap3"
 
@@ -114,5 +117,8 @@ Boards:
 - AM43x EPOS EVM
   compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43"
 
+- AM437x GP EVM
+  compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43"
+
 - DRA7 EVM:  Software Developement Board for DRA7XX
   compatible = "ti,dra7-evm", "ti,dra7"

Documentation/devicetree/bindings/usb/ehci-omap.txt

@@ -21,7 +21,7 @@ Documentation/devicetree/bindings/mfd/omap-usb-host.txt
 Example for OMAP4:
 
 usbhsehci: ehci@4a064c00 {
-	compatible = "ti,ehci-omap", "usb-ehci";
+	compatible = "ti,ehci-omap";
 	reg = <0x4a064c00 0x400>;
 	interrupts = <0 77 0x4>;
 };

Documentation/devicetree/bindings/usb/ohci-omap3.txt

@@ -9,7 +9,7 @@ Required properties:
 Example for OMAP4:
 
 usbhsohci: ohci@4a064800 {
-	compatible = "ti,ohci-omap3", "usb-ohci";
+	compatible = "ti,ohci-omap3";
 	reg = <0x4a064800 0x400>;
 	interrupts = <0 76 0x4>;
 };

arch/arm/boot/dts/Makefile

@@ -199,6 +199,10 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap2420-n810-wimax.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-cm-t3517.dtb \
+	omap3-sbc-t3517.dtb \
+	omap3-cm-t3530.dtb \
+	omap3-sbc-t3530.dtb \
 	omap3-cm-t3730.dtb \
 	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
@@ -214,7 +218,9 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-gta04.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \
+	omap3-lilly-dbb056.dtb \
 	omap3-zoom3.dtb \
+	omap4-duovero-parlor.dtb \
 	omap4-panda.dtb \
 	omap4-panda-a4.dtb \
 	omap4-panda-es.dtb \
@@ -228,9 +234,11 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-boneblack.dtb \
 	am335x-nano.dtb \
 	am335x-base0033.dtb \
+	am3517-craneboard.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
 	am43x-epos-evm.dtb \
+	am437x-gp-evm.dtb \
 	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb

arch/arm/boot/dts/am335x-evm.dts

@@ -260,6 +260,12 @@
 		>;
 	};
 
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
 	lcd_pins_s0: lcd_pins_s0 {
 		pinctrl-single,pins = <
 			0x20 0x01	/* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
@@ -434,9 +440,9 @@
 	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
 	nand@0,0 {
 		reg = <0 0 0>; /* CS0, offset 0 */
-		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		gpmc,device-nand = "true";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
@@ -460,50 +466,51 @@
 		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
-
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
 		#address-cells = <1>;
 		#size-cells = <1>;
-		elm_id = <&elm>;
-
-		/* MTD partition table */
 		partition@0 {
-			label = "SPL1";
+			label = "NAND.SPL";
 			reg = <0x00000000 0x000020000>;
 		};
-
 		partition@1 {
-			label = "SPL2";
+			label = "NAND.SPL.backup1";
 			reg = <0x00020000 0x00020000>;
 		};
-
 		partition@2 {
-			label = "SPL3";
+			label = "NAND.SPL.backup2";
 			reg = <0x00040000 0x00020000>;
 		};
-
 		partition@3 {
-			label = "SPL4";
+			label = "NAND.SPL.backup3";
 			reg = <0x00060000 0x00020000>;
 		};
-
 		partition@4 {
-			label = "U-boot";
+			label = "NAND.u-boot-spl";
-			reg = <0x00080000 0x001e0000>;
+			reg = <0x00080000 0x00040000>;
 		};
-
 		partition@5 {
-			label = "environment";
+			label = "NAND.u-boot";
-			reg = <0x00260000 0x00020000>;
+			reg = <0x000C0000 0x00100000>;
 		};
-
 		partition@6 {
-			label = "Kernel";
+			label = "NAND.u-boot-env";
-			reg = <0x00280000 0x00500000>;
+			reg = <0x001C0000 0x00020000>;
 		};
-
 		partition@7 {
-			label = "File-System";
+			label = "NAND.u-boot-env.backup1";
-			reg = <0x00780000 0x0F880000>;
+			reg = <0x001E0000 0x00020000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00200000 0x00800000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00A00000 0x0F600000>;
 		};
 	};
 };
@@ -643,6 +650,9 @@
 	status = "okay";
 	vmmc-supply = <&vmmc_reg>;
 	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 };
 
 &sham {

arch/arm/boot/dts/am335x-evmsk.dts

@@ -45,6 +45,18 @@
 		regulator-boot-on;
 	};
 
+	wl12xx_vmmc: fixedregulator@2 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_gpio>;
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 29 0>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
 	leds {
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_leds_s0>;
@@ -270,6 +282,24 @@
 			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
 		>;
 	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */
+			0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+			0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+			0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+			0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+			0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+			0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+		>;
+	};
+
+	wl12xx_gpio: pinmux_wl12xx_gpio {
+		pinctrl-single,pins = <
+			0x7c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 */
+		>;
+	};
 };
 
 &uart0 {
@@ -342,9 +372,22 @@
 		status = "okay";
 	};
 
+	usb-phy@47401b00 {
+		status = "okay";
+	};
+
 	usb@47401000 {
 		status = "okay";
 	};
+
+	usb@47401800 {
+		status = "okay";
+		dr_mode = "host";
+	};
+
+	dma-controller@07402000  {
+		status = "okay";
+	};
 };
 
 &epwmss2 {
@@ -440,6 +483,7 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
+	dual_emac = <1>;
 };
 
 &davinci_mdio {
@@ -451,11 +495,13 @@
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
 	phy-mode = "rgmii-txid";
+	dual_emac_res_vlan = <1>;
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
 	phy-mode = "rgmii-txid";
+	dual_emac_res_vlan = <2>;
 };
 
 &mmc1 {
@@ -479,6 +525,16 @@
 	ti,no-reset-on-init;
 };
 
+&mmc2 {
+	status = "okay";
+	vmmc-supply = <&wl12xx_vmmc>;
+	ti,non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+};
+
 &mcasp1 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcasp1_pins>;

arch/arm/boot/dts/am33xx.dtsi

@@ -58,6 +58,10 @@
 				275000  1125000
 			>;
 			voltage-tolerance = <2>; /* 2 percentage */
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
 			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
@@ -318,6 +322,7 @@
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x480ca000 0x1000>;
 			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
 		};
 
 		wdt2: wdt@44e35000 {
@@ -399,7 +404,7 @@
 			ti,timer-pwm;
 		};
 
-		rtc@44e3e000 {
+		rtc: rtc@44e3e000 {
 			compatible = "ti,da830-rtc";
 			reg = <0x44e3e000 0x1000>;
 			interrupts = <75
@@ -582,6 +587,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
+				interrupts = <31>;
+				interrupt-names = "ecap0";
 				ti,hwmods = "ecap0";
 				status = "disabled";
 			};
@@ -610,6 +617,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
+				interrupts = <47>;
+				interrupt-names = "ecap1";
 				ti,hwmods = "ecap1";
 				status = "disabled";
 			};
@@ -638,6 +647,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				interrupts = <61>;
+				interrupt-names = "ecap2";
 				ti,hwmods = "ecap2";
 				status = "disabled";
 			};

arch/arm/boot/dts/am3517-craneboard.dts

@@ -0,0 +1,174 @@
+/*
+ * See craneboard.org for more details
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am3517.dtsi"
+
+/ {
+	model = "TI AM3517 CraneBoard (TMDSEVM3517)";
+	compatible = "ti,am3517-craneboard", "ti,am3517", "ti,omap3";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;	/* 256 MB */
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+};
+
+&davinci_emac {
+	status = "okay";
+};
+
+&davinci_mdio {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&mmc1 {
+	vmmc-supply = <&vdd2_reg>;
+	bus-width = <8>;
+};
+
+&mmc2 {
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&mmc3 {
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+#include "tps65910.dtsi"
+
+&omap3_pmx_core {
+	tps_pins: pinmux_tps_pins {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq.sys_nirq */
+		>;
+	};
+};
+
+&tps {
+	pinctrl-names = "default";
+	pinctrl-0 = <&tps_pins>;
+
+	interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+	interrupt-parent = <&intc>;
+
+	ti,en-ck32k-xtal;
+
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		/*
+		 * Unused:
+		 * VDIG1=2.7V,300mA max
+		 * VDIG2=1.8V,300mA max
+		 */
+
+		vpll_reg: regulator@7 {
+			/* VDDS_DPLL_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			/* VDDS_SRAM_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			/* VDDA1P8V_USBPHY */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		/* VAUX33 unused */
+
+		vdac_reg: regulator@8 {
+			/* VDDA_DAC_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			/* VDDA3P3V_USBPHY */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_CORE */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDDSHV_3V3 */
+			regulator-name = "vdd_shv";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		/* VDD3 unused */
+	};
+};

arch/arm/boot/dts/am4372.dtsi

@@ -8,6 +8,7 @@
  * kind, whether express or implied.
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 #include "skeleton.dtsi"
@@ -33,6 +34,11 @@
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
 
@@ -351,6 +357,13 @@
 			status = "disabled";
 		};
 
+		hwspinlock: spinlock@480ca000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x480ca000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
 		i2c0: i2c@44e0b000 {
 			compatible = "ti,am4372-i2c","ti,omap4-i2c";
 			reg = <0x44e0b000 0x1000>;
@@ -521,6 +534,7 @@
 
 			ecap0: ecap@48300100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
 				ti,hwmods = "ecap0";
 				status = "disabled";
@@ -528,6 +542,7 @@
 
 			ehrpwm0: ehrpwm@48300200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
 				ti,hwmods = "ehrpwm0";
 				status = "disabled";
@@ -545,6 +560,7 @@
 
 			ecap1: ecap@48302100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
 				ti,hwmods = "ecap1";
 				status = "disabled";
@@ -552,6 +568,7 @@
 
 			ehrpwm1: ehrpwm@48302200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
 				ti,hwmods = "ehrpwm1";
 				status = "disabled";
@@ -569,6 +586,7 @@
 
 			ecap2: ecap@48304100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
 				ti,hwmods = "ecap2";
 				status = "disabled";
@@ -576,6 +594,7 @@
 
 			ehrpwm2: ehrpwm@48304200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
 				ti,hwmods = "ehrpwm2";
 				status = "disabled";
@@ -593,6 +612,7 @@
 
 			ehrpwm3: ehrpwm@48306200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48306200 0x80>;
 				ti,hwmods = "ehrpwm3";
 				status = "disabled";
@@ -610,6 +630,7 @@
 
 			ehrpwm4: ehrpwm@48308200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48308200 0x80>;
 				ti,hwmods = "ehrpwm4";
 				status = "disabled";
@@ -627,6 +648,7 @@
 
 			ehrpwm5: ehrpwm@4830a200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x4830a200 0x80>;
 				ti,hwmods = "ehrpwm5";
 				status = "disabled";
@@ -689,6 +711,30 @@
 			       <&edma 11>;
 			dma-names = "tx", "rx";
 		};
+
+		elm: elm@48080000 {
+			compatible = "ti,am3352-elm";
+			reg = <0x48080000 0x2000>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "elm";
+			clocks = <&l4ls_gclk>;
+			clock-names = "fck";
+			status = "disabled";
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,am3352-gpmc";
+			ti,hwmods = "gpmc";
+			clocks = <&l3s_gclk>;
+			clock-names = "fck";
+			reg = <0x50000000 0x2000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			gpmc,num-cs = <7>;
+			gpmc,num-waitpins = <2>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -0,0 +1,127 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* AM437x GP EVM */
+
+/dts-v1/;
+
+#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "TI AM437x GP EVM";
+	compatible = "ti,am437x-gp-evm","ti,am4372","ti,am43";
+
+	vmmcsd_fixed: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH /* Bank3, pin21 */
+				&gpio4 3 GPIO_ACTIVE_HIGH /* Bank4, pin3 */
+				&gpio4 2 GPIO_ACTIVE_HIGH>; /* Bank4, pin2 */
+
+		col-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH /* Bank3, pin19 */
+				&gpio3 20 GPIO_ACTIVE_HIGH>; /* Bank3, pin20 */
+
+		linux,keymap = <0x00000201      /* P1 */
+				0x00010202      /* P2 */
+				0x01000067      /* UP */
+				0x0101006a      /* RIGHT */
+				0x02000069      /* LEFT */
+				0x0201006c>;      /* DOWN */
+		};
+};
+
+&am43xx_pinmux {
+	i2c0_pins: i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	i2c1_pins: i2c1_pins {
+		pinctrl-single,pins = <
+			0x15c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_cs0.i2c1_scl */
+			0x158 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_d1.i2c1_sda  */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
+	ecap0_pins: backlight_pins {
+		pinctrl-single,pins = <
+			0x164 MUX_MODE0       /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+		>;
+	};
+};
+
+&i2c0 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c1_pins>;
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ecap0_pins>;
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
+};
+
+&gpio4 {
+	status = "okay";
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -13,6 +13,7 @@
 #include "am4372.dtsi"
 #include <dt-bindings/pinctrl/am43xx.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
@@ -79,6 +80,64 @@
 				0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 			>;
 		};
+
+		nand_flash_x8: nand_flash_x8 {
+			pinctrl-single,pins = <
+				0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.SELQSPIorNAND/GPIO */
+				0x0  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+				0x4  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+				0x8  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+				0xc  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+				0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+				0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+				0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+				0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+				0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+				0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpmc_wpn */
+				0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+				0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+				0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+				0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+				0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+			>;
+		};
+
+		ecap0_pins: backlight_pins {
+			pinctrl-single,pins = <
+				0x164 MUX_MODE0         /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+			>;
+		};
+
+		i2c2_pins: pinmux_i2c2_pins {
+			pinctrl-single,pins = <
+				0x1c0 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_sda.i2c2_sda */
+				0x1c4 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_scl.i2c2_scl */
+			>;
+		};
+
+		spi0_pins: pinmux_spi0_pins {
+			pinctrl-single,pins = <
+				0x150 (PIN_INPUT | MUX_MODE0)           /* spi0_clk.spi0_clk */
+				0x154 (PIN_OUTPUT | MUX_MODE0)           /* spi0_d0.spi0_d0 */
+				0x158 (PIN_INPUT | MUX_MODE0)           /* spi0_d1.spi0_d1 */
+				0x15c (PIN_OUTPUT | MUX_MODE0)          /* spi0_cs0.spi0_cs0 */
+			>;
+		};
+
+		spi1_pins: pinmux_spi1_pins {
+			pinctrl-single,pins = <
+				0x190 (PIN_INPUT | MUX_MODE3)           /* mcasp0_aclkx.spi1_clk */
+				0x194 (PIN_OUTPUT | MUX_MODE3)           /* mcasp0_fsx.spi1_d0 */
+				0x198 (PIN_INPUT | MUX_MODE3)           /* mcasp0_axr0.spi1_d1 */
+				0x19c (PIN_OUTPUT | MUX_MODE3)          /* mcasp0_ahclkr.spi1_cs0 */
+			>;
+		};
+
+		mmc1_pins: pinmux_mmc1_pins {
+			pinctrl-single,pins = <
+				0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+			>;
+		};
 	};
 
 	matrix_keypad: matrix_keypad@0 {
@@ -113,12 +172,22 @@
 				0x0203006c	/* DOWN */
 				0x03030069>;	/* LEFT */
 		};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
 };
 
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 };
 
 &mac {
@@ -169,6 +238,12 @@
 	};
 };
 
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
 &gpio0 {
 	status = "okay";
 };
@@ -184,3 +259,111 @@
 &gpio3 {
 	status = "okay";
 };
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_flash_x8>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <40>; /* tCEA + tCHZ + 1 */
+		gpmc,cs-wr-off-ns = <40>;
+		gpmc,adv-on-ns = <0>;  /* cs-on-ns */
+		gpmc,adv-rd-off-ns = <25>; /* min( tALH + tALS + 1) */
+		gpmc,adv-wr-off-ns = <25>; /* min( tALH + tALS + 1) */
+		gpmc,we-on-ns = <0>;   /* cs-on-ns */
+		gpmc,we-off-ns = <20>; /* we-on-time + tWP + 2 */
+		gpmc,oe-on-ns = <3>;  /* cs-on-ns + tRR + 2 */
+		gpmc,oe-off-ns = <30>; /* oe-on-ns + tRP + 2 */
+		gpmc,access-ns = <30>; /* tCEA + 4*/
+		gpmc,rd-cycle-ns = <40>;
+		gpmc,wr-cycle-ns = <40>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x00040000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00040000 0x00040000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x000C0000 0x00040000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00100000 0x00080000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x00180000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x00280000 0x00040000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x002C0000 0x00040000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00300000 0x00700000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00800000 0x1F600000>;
+		};
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ecap0_pins>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+	status = "okay";
+};

arch/arm/boot/dts/dra7.dtsi

@@ -47,6 +47,11 @@
 				1000000	1060000
 				1176000	1160000
 				>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 		cpu@1 {
 			device_type = "cpu";
@@ -464,6 +469,20 @@
 			ti,hwmods = "wd_timer2";
 		};
 
+		hwspinlock: spinlock@4a0f6000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x4a0f6000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
+		dmm@4e000000 {
+			compatible = "ti,omap5-dmm";
+			reg = <0x4e000000 0x800>;
+			interrupts = <0 113 0x4>;
+			ti,hwmods = "dmm";
+		};
+
 		i2c1: i2c@48070000 {
 			compatible = "ti,omap4-i2c";
 			reg = <0x48070000 0x100>;
@@ -559,6 +578,138 @@
 			status = "disabled";
 		};
 
+		abb_mpu: regulator-abb-mpu {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_mpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
+			      <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+			      <0x4ae0c158 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x80>;
+			/* LDOVBBMPU_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBMPU_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1060000		0	0x0	0 0x02000000 0x01F00000
+			1160000		0	0x4	0 0x02000000 0x01F00000
+			1210000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_ivahd: regulator-abb-ivahd {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_ivahd";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
+			      <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+			      <0x4a002470 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x40000000>;
+			/* LDOVBBIVA_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBIVA_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1055000		0	0x0	0 0x02000000 0x01F00000
+			1150000		0	0x4	0 0x02000000 0x01F00000
+			1250000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_dspeve: regulator-abb-dspeve {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_dspeve";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
+			      <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+			      <0x4a00246c 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x20000000>;
+			/* LDOVBBDSPEVE_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBDSPEVE_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1055000		0	0x0	0 0x02000000 0x01F00000
+			1150000		0	0x4	0 0x02000000 0x01F00000
+			1250000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_gpu: regulator-abb-gpu {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_gpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
+			      <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+			      <0x4ae0c154 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x10000000>;
+			/* LDOVBBGPU_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBGPU_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1090000		0	0x0	0 0x02000000 0x01F00000
+			1210000		0	0x4	0 0x02000000 0x01F00000
+			1280000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
 		mcspi1: spi@48098000 {
 			compatible = "ti,omap4-mcspi";
 			reg = <0x48098000 0x200>;

arch/arm/boot/dts/omap2.dtsi

@@ -271,5 +271,36 @@
 			ti,hwmods = "timer12";
 			ti,timer-pwm;
 		};
+
+		dss: dss@48050000 {
+			compatible = "ti,omap2-dss";
+			reg = <0x48050000 0x400>;
+			status = "disabled";
+			ti,hwmods = "dss_core";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			dispc@48050400 {
+				compatible = "ti,omap2-dispc";
+				reg = <0x48050400 0x400>;
+				interrupts = <25>;
+				ti,hwmods = "dss_dispc";
+			};
+
+			rfbi: encoder@48050800 {
+				compatible = "ti,omap2-rfbi";
+				reg = <0x48050800 0x400>;
+				status = "disabled";
+				ti,hwmods = "dss_rfbi";
+			};
+
+			venc: encoder@48050c00 {
+				compatible = "ti,omap2-venc";
+				reg = <0x48050c00 0x400>;
+				status = "disabled";
+				ti,hwmods = "dss_venc";
+			};
+		};
 	};
 };

arch/arm/boot/dts/omap2420.dtsi

@@ -99,6 +99,7 @@
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@48076000 {
@@ -112,6 +113,7 @@
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		msdi1: mmc@4809c000 {

arch/arm/boot/dts/omap2430.dtsi

@@ -113,6 +113,7 @@
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@48076000 {
@@ -128,6 +129,7 @@
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@4808c000 {
@@ -143,6 +145,7 @@
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp4: mcbsp@4808e000 {
@@ -158,6 +161,7 @@
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp5: mcbsp@48096000 {
@@ -173,6 +177,7 @@
 			dmas = <&sdma 21>,
 			       <&sdma 22>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mmc1: mmc@4809c000 {

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -24,6 +24,11 @@
 		reg = <0x80000000 0x20000000>; /* 512 MB */
 	};
 
+	aliases {
+		display0 = &dvi0;
+		display1 = &tv0;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -86,6 +91,60 @@
 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
 	};
+
+	tfp410: encoder@0 {
+		compatible = "ti,tfp410";
+		powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
+
+		/* XXX pinctrl from twl */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tfp410_in: endpoint@0 {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tfp410_out: endpoint@0 {
+					remote-endpoint = <&dvi_connector_in>;
+				};
+			};
+		};
+	};
+
+	dvi0: connector@0 {
+		compatible = "dvi-connector";
+		label = "dvi";
+
+		digital;
+
+		ddc-i2c-bus = <&i2c3>;
+
+		port {
+			dvi_connector_in: endpoint {
+				remote-endpoint = <&tfp410_out>;
+			};
+		};
+	};
+
+	tv0: connector@1 {
+		compatible = "svideo-connector";
+		label = "tv";
+
+		port {
+			tv_connector_in: endpoint {
+				remote-endpoint = <&venc_out>;
+			};
+		};
+	};
 };
 
 &omap3_pmx_wkup {
@@ -94,6 +153,17 @@
 			0x0e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot2.gpio_4 */
 		>;
 	};
+
+	dss_dpi_pins2: pinmux_dss_dpi_pins1 {
+		pinctrl-single,pins = <
+			0x0a (PIN_OUTPUT | MUX_MODE3)   /* sys_boot0.dss_data18 */
+			0x0c (PIN_OUTPUT | MUX_MODE3)   /* sys_boot1.dss_data19 */
+			0x10 (PIN_OUTPUT | MUX_MODE3)   /* sys_boot3.dss_data20 */
+			0x12 (PIN_OUTPUT | MUX_MODE3)   /* sys_boot4.dss_data21 */
+			0x14 (PIN_OUTPUT | MUX_MODE3)   /* sys_boot5.dss_data22 */
+			0x16 (PIN_OUTPUT | MUX_MODE3)   /* sys_boot6.dss_data23 */
+		>;
+	};
 };
 
 &omap3_pmx_core {
@@ -119,6 +189,35 @@
 			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
 		>;
 	};
+
+	dss_dpi_pins1: pinmux_dss_dpi_pins2 {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
+
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
+
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3)   /* dss_data18.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3)   /* dss_data19.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3)   /* dss_data20.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3)   /* dss_data21.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3)   /* dss_data22.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3)   /* dss_data23.dss_data5 */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {
@@ -164,15 +263,6 @@
 
 &i2c3 {
 	clock-frequency = <100000>;
-
-	/*
-	 * Display monitor features are burnt in the EEPROM
-	 * as EDID data.
-	 */
-	eeprom@50 {
-		compatible = "ti,eeprom";
-		reg = <0x50>;
-	};
 };
 
 &mmc1 {
@@ -234,3 +324,37 @@
 	regulator-max-microvolt = <1800000>;
 	regulator-always-on;
 };
+
+&mcbsp2 {
+	status = "okay";
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&dss_dpi_pins1
+		&dss_dpi_pins2
+	>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&tfp410_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+&venc {
+	status = "ok";
+
+	vdda-supply = <&vdac>;
+
+	port {
+		venc_out: endpoint {
+			remote-endpoint = <&tv_connector_in>;
+			ti,channels = <2>;
+		};
+	};
+};

arch/arm/boot/dts/omap3-beagle.dts

@@ -24,6 +24,11 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
+	aliases {
+		display0 = &dvi0;
+		display1 = &tv0;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pmu_stat {
@@ -80,6 +85,61 @@
 		};
 
 	};
+
+	tfp410: encoder@0 {
+		compatible = "ti,tfp410";
+		powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;	/* gpio_170 */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tfp410_pins>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tfp410_in: endpoint@0 {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tfp410_out: endpoint@0 {
+					remote-endpoint = <&dvi_connector_in>;
+				};
+			};
+		};
+	};
+
+	dvi0: connector@0 {
+		compatible = "dvi-connector";
+		label = "dvi";
+
+		digital;
+
+		ddc-i2c-bus = <&i2c3>;
+
+		port {
+			dvi_connector_in: endpoint {
+				remote-endpoint = <&tfp410_out>;
+			};
+		};
+	};
+
+	tv0: connector@1 {
+		compatible = "svideo-connector";
+		label = "tv";
+
+		port {
+			tv_connector_in: endpoint {
+				remote-endpoint = <&venc_out>;
+			};
+		};
+	};
 };
 
 &omap3_pmx_wkup {
@@ -113,6 +173,45 @@
 			0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
+
+	tfp410_pins: pinmux_tfp410_pins {
+		pinctrl-single,pins = <
+			0x194 (PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
+		>;
+	};
+
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			0x0a4 (PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			0x0a6 (PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			0x0a8 (PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			0x0aa (PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
+			0x0ac (PIN_OUTPUT | MUX_MODE0)   /* dss_data0.dss_data0 */
+			0x0ae (PIN_OUTPUT | MUX_MODE0)   /* dss_data1.dss_data1 */
+			0x0b0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data2.dss_data2 */
+			0x0b2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data3.dss_data3 */
+			0x0b4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data4.dss_data4 */
+			0x0b6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data5.dss_data5 */
+			0x0b8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
+			0x0ba (PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
+			0x0bc (PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
+			0x0be (PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
+			0x0c0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
+			0x0c2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
+			0x0c4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
+			0x0c6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
+			0x0c8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
+			0x0ca (PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
+			0x0cc (PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
+			0x0ce (PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
+			0x0d0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data18.dss_data18 */
+			0x0d2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data19.dss_data19 */
+			0x0d4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data20.dss_data20 */
+			0x0d6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data21.dss_data21 */
+			0x0d8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data22.dss_data22 */
+			0x0da (PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {
@@ -152,6 +251,10 @@
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
 
+&i2c3 {
+	clock-frequency = <100000>;
+};
+
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
 	vmmc_aux-supply = <&vsim>;
@@ -211,3 +314,39 @@
 	regulator-max-microvolt = <1800000>;
 	regulator-always-on;
 };
+
+&mcbsp2 {
+	status = "okay";
+};
+
+/* Needed to power the DPI pins */
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&tfp410_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+&venc {
+	status = "ok";
+
+	vdda-supply = <&vdac>;
+
+	port {
+		venc_out: endpoint {
+			remote-endpoint = <&tv_connector_in>;
+			ti,channels = <2>;
+		};
+	};
+};

arch/arm/boot/dts/omap3-cm-t3517.dts

@@ -0,0 +1,136 @@
+/*
+ * Support for CompuLab CM-T3517
+ */
+/dts-v1/;
+
+#include "am3517.dtsi"
+#include "omap3-cm-t3x.dtsi"
+
+/ {
+	model = "CompuLab CM-T3517";
+	compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+
+	vmmc:  regulator-vmmc {
+                compatible = "regulator-fixed";
+                regulator-name = "vmmc";
+                regulator-min-microvolt = <3300000>;
+                regulator-max-microvolt = <3300000>;
+        };
+
+	wl12xx_vmmc2: wl12xx_vmmc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vw1271";
+		pinctrl-names = "default";
+		pinctrl-0 = <
+				&wl12xx_wkup_pins
+				&wl12xx_core_pins
+			    >;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */
+		startup-delay-us = <20000>;
+		enable-active-high;
+	};
+
+	wl12xx_vaux2: wl12xx_vaux2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271_vaux2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+};
+
+&omap3_pmx_wkup {
+
+	wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
+			OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4)	/* sys_boot4.gpio_6 */
+		>;
+	};
+};
+
+&omap3_pmx_core {
+
+	phy1_reset_pins: pinmux_hsusb1_phy_reset_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4)	/* uart2_tx.gpio_146 */
+		>;
+	};
+
+	phy2_reset_pins: pinmux_hsusb2_phy_reset_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4)	/* uart2_rx.gpio_147 */
+		>;
+	};
+
+	otg_drv_vbus: pinmux_otg_drv_vbus {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
+		>;
+	};
+
+	wl12xx_core_pins: pinmux_wl12xx_core_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs5.gpio_56 */
+			OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart2_rts.gpio_145 */
+		>;
+	};
+
+	usb_hub_pins: pinmux_usb_hub_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 - USB HUB RST */
+		>;
+	};
+};
+
+&hsusb1_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&phy1_reset_pins>;
+	reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
+};
+
+&hsusb2_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&phy2_reset_pins>;
+	reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;
+};
+
+&davinci_emac {
+	status = "okay";
+};
+
+&davinci_mdio {
+	status = "okay";
+};
+
+&am35x_otg_hs {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&otg_drv_vbus>;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc>;
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&wl12xx_vmmc2>;
+	vmmc_aux-supply = <&wl12xx_vaux2>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+};

arch/arm/boot/dts/omap3-cm-t3530.dts

@@ -0,0 +1,48 @@
+/*
+ * Support for CompuLab CM-T3530
+ */
+/dts-v1/;
+
+#include "omap34xx.dtsi"
+#include "omap3-cm-t3x30.dtsi"
+
+/ {
+	model = "CompuLab CM-T3530";
+	compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+
+	/* Regulator to trigger the reset signal of the Wifi module */
+	mmc2_sdio_reset: regulator-mmc2-sdio-reset {
+		compatible = "regulator-fixed";
+		regulator-name = "regulator-mmc2-sdio-reset";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&omap3_pmx_core {
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat3.sdmmc2_dat3 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat4.sdmmc2_dir_dat0 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat5.sdmmc2_dir_dat1 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat6.sdmmc2_dir_cmd */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1)		/* sdmmc2_dat7.sdmmc2_clkin */
+		>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&mmc2_sdio_reset>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+};

arch/arm/boot/dts/omap3-cm-t3730.dts

@@ -32,57 +32,26 @@
 };
 
 &omap3_pmx_core {
-	mmc1_pins: pinmux_mmc1_pins {
-		pinctrl-single,pins = <
-			0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
-			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
-			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0.sdmmc1_dat0 */
-			0x11a (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat1.sdmmc1_dat1 */
-			0x11c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat2.sdmmc1_dat2 */
-			0x11e (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat3.sdmmc1_dat3 */
-		>;
-	};
 
 	mmc2_pins: pinmux_mmc2_pins {
 		pinctrl-single,pins = <
-			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
-			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
-			0x12c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
-			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
-			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
-			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
-		>;
-	};
-
-	smsc1_pins: pinmux_smsc1_pins {
-		pinctrl-single,pins = <
-			0x88 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs5.gpmc_ncs5 */
-			0x16a (PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
-		>;
-	};
-
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
-			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
 	wl12xx_gpio: pinmux_wl12xx_gpio {
 		pinctrl-single,pins = <
-			0xb2 (PIN_OUTPUT | MUX_MODE4)		/* dss_data3.gpio_73 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4)	/* dss_data3.gpio_73 */
-			0x134 (PIN_INPUT | MUX_MODE4)		/* sdmmc2_dat4.gpio_136 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4)	/* sdmmc2_dat4.gpio_136 */
 		>;
 	};
 };
 
-&mmc1 {
-	vmmc-supply = <&vmmc1>;
-	bus-width = <4>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
-};
-
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
@@ -92,13 +61,3 @@
 	bus-width = <4>;
 	cap-power-off-card;
 };
-
-&smsc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&smsc1_pins>;
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins>;
-};

arch/arm/boot/dts/omap3-cm-t3x.dtsi

@@ -0,0 +1,110 @@
+/*
+ * Common support for CompuLab CM-T3x CoMs
+ */
+
+/ {
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&green_led_pins>;
+		ledb {
+			label = "cm-t3x:green";
+			gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>;  /* gpio186 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	/* HS USB Port 1 Power */
+	hsusb1_power: hsusb1_power_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <70000>;
+	};
+
+	/* HS USB Port 2 Power */
+	hsusb2_power: hsusb2_power_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb2_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <70000>;
+	};
+
+	/* HS USB Host PHY on PORT 1 */
+	hsusb1_phy: hsusb1_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&hsusb1_power>;
+	};
+
+	/* HS USB Host PHY on PORT 2 */
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&hsusb2_power>;
+	};
+};
+
+&omap3_pmx_core {
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT  | MUX_MODE0)	/* uart3_rx_irrx.uart3_rx_irrx */
+			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx_irtx.uart3_tx_irtx */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	green_led_pins: pinmux_green_led_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21e2, PIN_OUTPUT | MUX_MODE4)	/* sys_clkout2.gpio_186 */
+		>;
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	bus-width = <4>;
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+};
+&usbhshost {
+	port1-mode = "ehci-phy";
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy &hsusb2_phy>;
+};

arch/arm/boot/dts/omap3-cm-t3x30.dtsi

@@ -1,28 +1,16 @@
 /*
- * Common support for CompuLab CM-T3530 and  CM-T3730
+ * Common support for CompuLab CM-T3x30 CoMs
  */
 
-/ {
+#include "omap3-cm-t3x.dtsi"
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x10000000>; /* 256 MB */
-	};
 
+/ {
 	cpus {
 		cpu@0 {
 			cpu0-supply = <&vcc>;
 		};
 	};
 
-	leds {
-		compatible = "gpio-leds";
-		ledb {
-			label = "cm-t35:green";
-			gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>;  /* gpio186 */
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
 	vddvario: regulator-vddvario {
 		compatible = "regulator-fixed";
 		regulator-name = "vddvario";
@@ -36,11 +24,40 @@
 	};
 };
 
+&omap3_pmx_core {
+
+	smsc1_pins: pinmux_smsc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs5.gpmc_ncs5 */
+			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
+		>;
+	};
+
+ 	hsusb0_pins: pinmux_hsusb0_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */
+			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */
+			OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
+			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
+			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data0.hsusb2_data0 */
+			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
+			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
+			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data3 */
+			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data4 */
+			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data5 */
+			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data6 */
+			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
+		>;
+	};
+};
+
 &gpmc {
 	ranges = <5 0 0x2c000000 0x01000000>;
 
 	smsc1: ethernet@5,0 {
 		compatible = "smsc,lan9221", "smsc,lan9115";
+		pinctrl-names = "default";
+		pinctrl-0 = <&smsc1_pins>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		reg = <5 0 0xff>;
@@ -74,8 +91,6 @@
 };
 
 &i2c1 {
-	clock-frequency = <400000>;
-
 	twl: twl@48 {
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
@@ -86,10 +101,31 @@
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
 
-&i2c3 {
+&mmc1 {
-	clock-frequency = <400000>;
+	vmmc-supply = <&vmmc1>;
 };
 
 &twl_gpio {
 	ti,use-leds;
+	/* pullups: BIT(0) */
+	ti,pullups = <0x000001>;
+};
+
+&hsusb1_phy {
+	reset-gpios = <&twl_gpio 6 GPIO_ACTIVE_LOW>;
+};
+
+&hsusb2_phy {
+	reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>;
+};
+
+&usb_otg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb0_pins>;
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
 };

arch/arm/boot/dts/omap3-devkit8000.dts

@@ -101,20 +101,8 @@
 	status = "disabled";
 };
 
-&mcbsp1 {
+&mcbsp2 {
-	status = "disabled";
+	status = "okay";
-};
-
-&mcbsp3 {
-	status = "disabled";
-};
-
-&mcbsp4 {
-	status = "disabled";
-};
-
-&mcbsp5 {
-	status = "disabled";
 };
 
 &gpmc {

arch/arm/boot/dts/omap3-gta04.dts

@@ -36,6 +36,14 @@
 			gpio-key,wakeup;
 		};
 	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "gta04";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
 };
 
 &omap3_pmx_core {
@@ -80,6 +88,12 @@
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
 	};
+
+	twl_audio: audio {
+		compatible = "ti,twl4030-audio";
+		codec {
+		};
+	};
 };
 
 #include "twl4030.dtsi"
@@ -96,6 +110,14 @@
 		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
 	};
 
+	/* accelerometer */
+	bma180@41 {
+		compatible = "bosch,bma180";
+		reg = <0x41>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
 	/* leds */
 	tca6507@45 {
 		compatible = "ti,tca6507";
@@ -124,6 +146,22 @@
 			reg = <0x4>;
 		};
 	};
+
+	/* compass aka magnetometer */
+	hmc5843@1e {
+		compatible = "honeywell,hmc5843";
+		reg = <0x1e>;
+	};
+
+	/* touchscreen */
+	tsc2007@48 {
+		compatible = "ti,tsc2007";
+		reg = <0x48>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		gpios = <&gpio6 0 GPIO_ACTIVE_LOW>;
+		ti,x-plate-ohms = <600>;
+	};
 };
 
 &i2c3 {
@@ -148,7 +186,9 @@
 };
 
 &mmc2 {
-	status = "disabled";
+	vmmc-supply = <&vaux4>;
+	bus-width = <4>;
+	ti,non-removable;
 };
 
 &mmc3 {
@@ -170,3 +210,12 @@
 	pinctrl-0 = <&uart3_pins>;
 };
 
+&charger {
+	bb_uvolt = <3200000>;
+	bb_uamp = <150>;
+};
+
+&vaux4 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <3150000>;
+};

arch/arm/boot/dts/omap3-igep.dtsi

@@ -170,6 +170,7 @@
 &mcbsp2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp2_pins>;
+	status = "okay";
 };
 
 &mmc1 {

arch/arm/boot/dts/omap3-igep0020.dts

@@ -61,22 +61,63 @@
 		reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
 		vcc-supply = <&hsusb1_power>;
 	};
+
+	tfp410: encoder@0 {
+		compatible = "ti,tfp410";
+		powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* gpio_170 */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tfp410_in: endpoint@0 {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tfp410_out: endpoint@0 {
+					remote-endpoint = <&dvi_connector_in>;
+				};
+			};
+		};
+	};
+
+	dvi0: connector@0 {
+		compatible = "dvi-connector";
+		label = "dvi";
+
+		digital;
+
+		ddc-i2c-bus = <&i2c3>;
+
+		port {
+			dvi_connector_in: endpoint {
+				remote-endpoint = <&tfp410_out>;
+			};
+		};
+	};
 };
 
 &omap3_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
 		&tfp410_pins
-		&dss_pins
+		&dss_dpi_pins
 	>;
 
-	tfp410_pins: tfp410_dvi_pins {
+	tfp410_pins: pinmux_tfp410_pins {
 		pinctrl-single,pins = <
 			0x196 (PIN_OUTPUT | MUX_MODE4)   /* hdq_sio.gpio_170 */
 		>;
 	};
 
-	dss_pins: pinmux_dss_dvi_pins {
+	dss_dpi_pins: pinmux_dss_dpi_pins {
 		pinctrl-single,pins = <
 			0x0a4 (PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
 			0x0a6 (PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
@@ -226,3 +267,14 @@
         /* Needed for DSS */
         regulator-name = "vdds_dsi";
 };
+
+&dss {
+	status = "ok";
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&tfp410_in>;
+			data-lines = <24>;
+		};
+	};
+};

arch/arm/boot/dts/omap3-lilly-a83x.dtsi

@@ -0,0 +1,459 @@
+/*
+ * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include "omap36xx.dtsi"
+
+/ {
+	model = "INCOstartec LILLY-A83X module (DM3730)";
+	compatible = "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3";
+
+	chosen {
+			bootargs = "console=ttyO0,115200n8 vt.global_cursor_default=0 consoleblank=0";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x8000000>;   /* 128 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "lilly-a83x::led1";
+			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "lilly-a83x";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
+
+	reg_vcc3: vcc3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	hsusb1_phy: hsusb1_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_vcc3>;
+	};
+};
+
+&omap3_pmx_wkup {
+	pinctrl-names = "default";
+
+	lan9221_pins: pinmux_lan9221_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4)   /* reserved.gpio_129 */
+		>;
+	};
+
+	tsc2048_pins: pinmux_tsc2048_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a16, PIN_INPUT_PULLUP | MUX_MODE4)   /* sys_boot6.gpio_8 */
+		>;
+	};
+
+	mmc1cd_pins: pinmux_mmc1cd_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4)   /* reserved.gpio_126 */
+		>;
+	};
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0)   /* uart1_tx.uart1_tx */
+			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0)   /* uart1_rts.uart1_rts */
+			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0)    /* uart1_cts.uart1_cts */
+			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0)    /* uart1_rx.uart1_rx */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1)   /* mcbsp3_clkx.uart2_tx */
+			OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1)    /* mcbsp3_fsx.uart2_rx */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)    /* uart3_rx_irrx.uart3_rx_irrx */
+			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)   /* uart3_tx_irtx.uart3_tx_irtx */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21ba ,PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_scl.i2c1_scl */
+			OMAP3_CORE1_IOPAD(0x21bc ,PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_sda.i2c1_sda */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)   /* i2c2_scl.i2c2_scl */
+			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)   /* i2c2_sda.i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)   /* i2c3_scl.i2c3_scl */
+			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)   /* i2c3_sda.i2c3_sda */
+		>;
+	};
+
+	hsusb1_pins: pinmux_hsusb1_pins {
+		pinctrl-single,pins = <
+
+			/* GPIO 182 controls USB-Hub reset. But USB-Phy its
+			 * reset can't be controlled. So we clamp this GPIO to
+			 * high (PIN_OFF_OUTPUT_HIGH) to always enable USB-Hub.
+			 */
+
+			OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT_PULLUP | PIN_OFF_OUTPUT_HIGH | MUX_MODE4)   /* mcspi2_cs1.gpio_182 */
+		>;
+	};
+
+	hsusb_otg_pins: pinmux_hsusb_otg_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)   /* hsusb0_clk.hsusb0_clk */
+			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)  /* hsusb0_stp.hsusb0_stp */
+			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0)   /* hsusb0_dir.hsusb0_dir */
+			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0)   /* hsusb0_nxt.hsusb0_nxt */
+			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0)   /* hsusb0_data0.hsusb0_data0 */
+			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0)   /* hsusb0_data1.hsusb0_data1 */
+			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0)   /* hsusb0_data2.hsusb0_data2 */
+			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0)   /* hsusb0_data3.hsusb0_data3 */
+			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0)   /* hsusb0_data4.hsusb0_data4 */
+			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0)   /* hsusb0_data5.hsusb0_data5 */
+			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0)   /* hsusb0_data6.hsusb0_data6 */
+			OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0)   /* hsusb0_data7.hsusb0_data7 */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	spi2_pins: pinmux_spi2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_clk.mcspi2_clk */
+			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_simo.mcspi2_simo */
+			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_somi.mcspi2_somi */
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE0)   /* mcspi2_cs0.mcspi2_cs0 */
+		>;
+	};
+};
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb1_2_pins
+	>;
+
+	hsusb1_2_pins: pinmux_hsusb1_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3)  /* etk_clk.hsusb1_stp */
+			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT | MUX_MODE3)   /* etk_ctl.hsusb1_clk */
+			OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE3)   /* etk_d0.hsusb1_data0 */
+			OMAP3630_CORE2_IOPAD(0x25de, PIN_INPUT | MUX_MODE3)   /* etk_d1.hsusb1_data1 */
+			OMAP3630_CORE2_IOPAD(0x25e0, PIN_INPUT | MUX_MODE3)   /* etk_d2.hsusb1_data2 */
+			OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT | MUX_MODE3)   /* etk_d3.hsusb1_data7 */
+			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT | MUX_MODE3)   /* etk_d4.hsusb1_data4 */
+			OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT | MUX_MODE3)   /* etk_d5.hsusb1_data5 */
+			OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT | MUX_MODE3)   /* etk_d6.hsusb1_data6 */
+			OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE3)   /* etk_d7.hsusb1_data3 */
+			OMAP3630_CORE2_IOPAD(0x25ec, PIN_INPUT | MUX_MODE3)   /* etk_d8.hsusb1_dir */
+			OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE3)   /* etk_d9.hsusb1_nxt */
+		>;
+	};
+
+	gpio1_pins: pinmux_gpio1_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_OUTPUT_PULLDOWN | MUX_MODE4)   /* etk_d15.gpio_29 */
+		>;
+	};
+
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio1_pins>;
+};
+
+&gpio6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb1_pins>;
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>;   /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
+	};
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&twl {
+	vmmc1: regulator-vmmc1 {
+		regulator-always-on;
+	};
+
+	vdd1: regulator-vdd1 {
+		regulator-always-on;
+	};
+
+	vdd2: regulator-vdd2 {
+		regulator-always-on;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <2600000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+};
+
+&i2c3 {
+	clock-frequency = <2600000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+		gpiom1: gpio@20 {
+			compatible = "mcp,mcp23017";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x20>;
+		};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&mmc1 {
+	cd-gpios = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+	cd-inverted;
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins &mmc1cd_pins>;
+	cap-sdio-irq;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&mcspi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins>;
+
+	tsc2046@0 {
+		reg = <0>;   /* CS0 */
+		compatible = "ti,tsc2046";
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 0>;   /* boot6 / gpio_8 */
+		spi-max-frequency = <1000000>;
+		pendown-gpio = <&gpio1 8 0>;
+		vcc-supply = <&reg_vcc3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsc2048_pins>;
+
+		ti,x-min = <300>;
+		ti,x-max = <3000>;
+		ti,y-min = <600>;
+		ti,y-max = <3600>;
+		ti,x-plate-ohms = <80>;
+		ti,pressure-max = <255>;
+		ti,swap-xy;
+
+		linux,wakeup;
+	};
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy>;
+};
+
+&usbhshost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb1_2_pins>;
+	num-ports = <2>;
+	port1-mode = "ehci-phy";
+};
+
+&usb_otg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb_otg_pins>;
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
+};
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x1000000>,
+		<7 0 0x15000000 0x01000000>;
+
+	nand@0,0 {
+		reg = <0 0 0x1000000>;
+		nand-bus-width = <16>;
+		ti,nand-ecc-opt = "bch8";
+		/* no elm on omap3 */
+
+		gpmc,mux-add-data = <0>;
+		gpmc,device-nand;
+		gpmc,device-width = <2>;
+		gpmc,wait-pin = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,burst-length= <4>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <100>;
+		gpmc,cs-wr-off-ns = <100>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <100>;
+		gpmc,adv-wr-off-ns = <100>;
+		gpmc,oe-on-ns = <5>;
+		gpmc,oe-off-ns = <75>;
+		gpmc,we-on-ns = <5>;
+		gpmc,we-off-ns = <75>;
+		gpmc,rd-cycle-ns = <100>;
+		gpmc,wr-cycle-ns = <100>;
+		gpmc,access-ns = <60>;
+		gpmc,page-burst-access-ns = <5>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-delay-ns = <50>;
+		gpmc,wr-data-mux-bus-ns = <75>;
+		gpmc,wr-access-ns = <155>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "MLO";
+			reg = <0 0x80000>;
+		};
+
+		partition@0x80000 {
+			label = "u-boot";
+			reg = <0x80000 0x1e0000>;
+		};
+
+		partition@0x260000 {
+			label = "u-boot-environment";
+			reg = <0x260000 0x20000>;
+		};
+
+		partition@0x280000 {
+			label = "kernel";
+			reg = <0x280000 0x500000>;
+		};
+
+		partition@0x780000 {
+			label = "filesystem";
+			reg = <0x780000 0xf880000>;
+		};
+	};
+
+	ethernet@7,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		bank-width = <2>;
+		gpmc,mux-add-data = <2>;
+		gpmc,cs-on-ns = <10>;
+		gpmc,cs-rd-off-ns = <60>;
+		gpmc,cs-wr-off-ns = <60>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <10>;
+		gpmc,adv-wr-off-ns = <10>;
+		gpmc,oe-on-ns = <10>;
+		gpmc,oe-off-ns = <60>;
+		gpmc,we-on-ns = <10>;
+		gpmc,we-off-ns = <60>;
+		gpmc,rd-cycle-ns = <100>;
+		gpmc,wr-cycle-ns = <100>;
+		gpmc,access-ns = <50>;
+		gpmc,page-burst-access-ns = <5>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <75>;
+		gpmc,wr-data-mux-bus-ns = <15>;
+		gpmc,wr-access-ns = <75>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&reg_vcc3>;
+		vdd33a-supply = <&reg_vcc3>;
+		reg-io-width = <4>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 0x2>;
+		reg = <7 0 0xff>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lan9221_pins>;
+		phy-mode = "mii";
+	};
+};

arch/arm/boot/dts/omap3-lilly-dbb056.dts

@@ -0,0 +1,170 @@
+/*
+ * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+/dts-v1/;
+
+#include "omap3-lilly-a83x.dtsi"
+
+/ {
+	model = "INCOstartec LILLY-DBB056 (DM3730)";
+	compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3";
+};
+
+&twl {
+	vaux2: regulator-vaux2 {
+		compatible = "ti,twl4030-vaux2";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_pins>;
+
+	lan9117_pins: pinmux_lan9117_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE4)   /* cam_fld.gpio_98 */
+		>;
+	};
+
+	gpio4_pins: pinmux_gpio4_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT | MUX_MODE4)   /* cam_xclkb.gpio_111 -> sja1000 IRQ */
+		>;
+	};
+
+	gpio5_pins: pinmux_gpio5_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x218c, PIN_OUTPUT | PIN_OFF_OUTPUT_HIGH | MUX_MODE4)   /* mcbsp1_clk.gpio_156 -> enable DSS */
+		>;
+	};
+
+	lcd_pins: pinmux_lcd_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)   /* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)   /* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)   /* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)   /* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)   /* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)   /* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_dat3.sdmmc2_dat3 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1)   /* sdmmc2_dat4.sdmmc2_dir_dat0 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1)   /* sdmmc2_dat5.sdmmc2_dir_dat1 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1)   /* sdmmc2_dat6.sdmmc2_dir_cmd */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1)    /* sdmmc2_dat7.sdmmc2_clkin */
+			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4)   /* uart3_cts_rctx.gpio_163 -> wp */
+			OMAP3_CORE1_IOPAD(0x219c, PIN_INPUT_PULLUP | MUX_MODE4)   /* uart3_rts_sd.gpio_164 -> cd */
+		>;
+	};
+
+	spi1_pins: pinmux_spi1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)   /* mcspi1_clk.mcspi1_clk */
+			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)   /* mcspi1_simo.mcspi1_simo */
+			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0)   /* mcspi1_somi.mcspi1_somi */
+			OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi1_cs0.mcspi1_cs0 */
+		>;
+	};
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio4_pins>;
+};
+
+&gpio5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio5_pins>;
+};
+
+&mmc2 {
+	status = "okay";
+	bus-width = <4>;
+	vmmc-supply = <&vmmc1>;
+	cd-gpios = <&gpio6 4 0>;   /* gpio_164 */
+	wp-gpios = <&gpio6 3 0>;   /* gpio_163 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	ti,dual-volt;
+};
+
+&mcspi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+};
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x1000000>,   /* nand assigned by COM a83x */
+		<4 0 0x20000000 0x01000000>,
+		<7 0 0x15000000 0x01000000>;   /* eth assigend by COM a83x */
+
+	ethernet@4,0 {
+		compatible = "smsc,lan9117", "smsc,lan9115";
+		bank-width = <2>;
+		gpmc,mux-add-data = <2>;
+		gpmc,cs-on-ns = <10>;
+		gpmc,cs-rd-off-ns = <65>;
+		gpmc,cs-wr-off-ns = <65>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <10>;
+		gpmc,adv-wr-off-ns = <10>;
+		gpmc,oe-on-ns = <10>;
+		gpmc,oe-off-ns = <65>;
+		gpmc,we-on-ns = <10>;
+		gpmc,we-off-ns = <65>;
+		gpmc,rd-cycle-ns = <100>;
+		gpmc,wr-cycle-ns = <100>;
+		gpmc,access-ns = <60>;
+		gpmc,page-burst-access-ns = <5>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <75>;
+		gpmc,wr-data-mux-bus-ns = <15>;
+		gpmc,wr-access-ns = <75>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&reg_vcc3>;
+		vdd33a-supply = <&reg_vcc3>;
+		reg-io-width = <4>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <2 0x2>;
+		reg = <4 0 0xff>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lan9117_pins>;
+		phy-mode = "mii";
+		smsc,force-internal-phy;
+	};
+};

arch/arm/boot/dts/omap3-n900.dts

@@ -74,6 +74,22 @@
 		};
 	};
 
+	isp1704: isp1704 {
+		compatible = "nxp,isp1704";
+		nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+		usb-phy = <&usb2_phy>;
+	};
+
+	tv: connector {
+		compatible = "composite-connector";
+		label = "tv";
+
+		port {
+			tv_connector_in: endpoint {
+				remote-endpoint = <&venc_out>;
+			};
+		};
+	};
 };
 
 &omap3_pmx_core {
@@ -140,11 +156,23 @@
 		>;
 	};
 
-	display_pins: pinmux_display_pins {
+	acx565akm_pins: pinmux_acx565akm_pins {
 		pinctrl-single,pins = <
 			0x0d4 (PIN_OUTPUT | MUX_MODE4)		/* RX51_LCD_RESET_GPIO */
 		>;
 	};
+
+	dss_sdi_pins: pinmux_dss_sdi_pins {
+		pinctrl-single,pins = <
+			0x0c0 (PIN_OUTPUT | MUX_MODE1)   /* dss_data10.sdi_dat1n */
+			0x0c2 (PIN_OUTPUT | MUX_MODE1)   /* dss_data11.sdi_dat1p */
+			0x0c4 (PIN_OUTPUT | MUX_MODE1)   /* dss_data12.sdi_dat2n */
+			0x0c6 (PIN_OUTPUT | MUX_MODE1)   /* dss_data13.sdi_dat2p */
+
+			0x0d8 (PIN_OUTPUT | MUX_MODE1)   /* dss_data22.sdi_clkp */
+			0x0da (PIN_OUTPUT | MUX_MODE1)   /* dss_data23.sdi_clkn */
+		>;
+	};
 };
 
 &i2c1 {
@@ -254,6 +282,61 @@
 	};
 };
 
+&twl_keypad {
+	linux,keymap = < 0x00000010 /* KEY_Q */
+			 0x00010018 /* KEY_O */
+			 0x00020019 /* KEY_P */
+			 0x00030033 /* KEY_COMMA */
+			 0x0004000e /* KEY_BACKSPACE */
+			 0x0006001e /* KEY_A */
+			 0x0007001f /* KEY_S */
+
+			 0x01000011 /* KEY_W */
+			 0x01010020 /* KEY_D */
+			 0x01020021 /* KEY_F */
+			 0x01030022 /* KEY_G */
+			 0x01040023 /* KEY_H */
+			 0x01050024 /* KEY_J */
+			 0x01060025 /* KEY_K */
+			 0x01070026 /* KEY_L */
+
+			 0x02000012 /* KEY_E */
+			 0x02010034 /* KEY_DOT */
+			 0x02020067 /* KEY_UP */
+			 0x0203001c /* KEY_ENTER */
+			 0x0205002c /* KEY_Z */
+			 0x0206002d /* KEY_X */
+			 0x0207002e /* KEY_C */
+			 0x02080043 /* KEY_F9 */
+
+			 0x03000013 /* KEY_R */
+			 0x0301002f /* KEY_V */
+			 0x03020030 /* KEY_B */
+			 0x03030031 /* KEY_N */
+			 0x03040032 /* KEY_M */
+			 0x03050039 /* KEY_SPACE */
+			 0x03060039 /* KEY_SPACE */
+			 0x03070069 /* KEY_LEFT */
+
+			 0x04000014 /* KEY_T */
+			 0x0401006c /* KEY_DOWN */
+			 0x0402006a /* KEY_RIGHT */
+			 0x0404001d /* KEY_LEFTCTRL */
+			 0x04050064 /* KEY_RIGHTALT */
+			 0x0406002a /* KEY_LEFTSHIFT */
+			 0x04080044 /* KEY_F10 */
+
+			 0x05000015 /* KEY_Y */
+			 0x05080057 /* KEY_F11 */
+
+			 0x06000016 /* KEY_U */
+
+			 0x07000017 /* KEY_I */
+			 0x07010041 /* KEY_F7 */
+			 0x07020042 /* KEY_F8 */
+			 >;
+};
+
 &twl_gpio {
 	ti,pullups	= <0x0>;
 	ti,pulldowns	= <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
@@ -291,6 +374,13 @@
 		DVDD-supply = <&vio>;
 	};
 
+	tsl2563: tsl2563@29 {
+		compatible = "amstaos,tsl2563";
+		reg = <0x29>;
+
+		amstaos,cover-comp-gain = <16>;
+	};
+
 	lp5523: lp5523@32 {
 		compatible = "national,lp5523";
 		reg = <0x32>;
@@ -356,6 +446,29 @@
 		compatible = "ti,bq27200";
 		reg = <0x55>;
 	};
+
+	tpa6130a2: tpa6130a2@60 {
+		compatible = "ti,tpa6130a2";
+		reg = <0x60>;
+
+		Vdd-supply = <&vmmc2>;
+
+		power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
+	};
+
+	bq24150a: bq24150a@6b {
+		compatible = "ti,bq24150a";
+		reg = <0x6b>;
+
+		ti,current-limit = <100>;
+		ti,weak-battery-voltage = <3400>;
+		ti,battery-regulation-voltage = <4200>;
+		ti,charge-current = <650>;
+		ti,termination-current = <100>;
+		ti,resistor-sense = <68>;
+
+		ti,usb-charger-detection = <&isp1704>;
+	};
 };
 
 &i2c3 {
@@ -471,13 +584,23 @@
 		spi-max-frequency = <6000000>;
 		reg = <0>;
 	};
-	mipid@2 {
+
-		compatible = "acx565akm";
+	acx565akm@2 {
+		compatible = "sony,acx565akm";
 		spi-max-frequency = <6000000>;
 		reg = <2>;
 
 		pinctrl-names = "default";
-		pinctrl-0 = <&display_pins>;
+		pinctrl-0 = <&acx565akm_pins>;
+
+		label = "lcd";
+		reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&sdi_out>;
+			};
+		};
 	};
 };
 
@@ -503,3 +626,39 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;
 };
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_sdi_pins>;
+
+	vdds_sdi-supply = <&vaux1>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			reg = <1>;
+
+			sdi_out: endpoint {
+				remote-endpoint = <&lcd_in>;
+				datapairs = <2>;
+			};
+		};
+	};
+};
+
+&venc {
+	status = "ok";
+
+	vdda-supply = <&vdac>;
+
+	port {
+		venc_out: endpoint {
+			remote-endpoint = <&tv_connector_in>;
+			ti,channels = <1>;
+		};
+	};
+};

arch/arm/boot/dts/omap3-overo.dtsi

@@ -92,3 +92,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;
 };
+
+&mcbsp2 {
+	status = "okay";
+};

arch/arm/boot/dts/omap3-sb-t35.dtsi

@@ -2,11 +2,36 @@
  * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
  */
 
+/ {
+	vddvario_sb_t35: regulator-vddvario-sb-t35 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
+	};
+
+	vdd33a_sb_t35: regulator-vdd33a-sb-t35 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33a";
+		regulator-always-on;
+	};
+};
+
+&omap3_pmx_core {
+	smsc2_pins: pinmux_smsc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs4.gpmc_ncs4 */
+			OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
+		>;
+	};
+};
+
 &gpmc {
 	ranges = <4 0 0x2d000000 0x01000000>;
 
 	smsc2: ethernet@4,0 {
 		compatible = "smsc,lan9221", "smsc,lan9115";
+		pinctrl-names = "default";
+		pinctrl-0 = <&smsc2_pins>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 		reg = <4 0 0xff>;
@@ -32,8 +57,8 @@
 		gpmc,wr-access-ns = <186>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
-		vddvario-supply = <&vddvario>;
+		vddvario-supply = <&vddvario_sb_t35>;
-		vdd33a-supply = <&vdd33a>;
+		vdd33a-supply = <&vdd33a_sb_t35>;
 		reg-io-width = <4>;
 		smsc,save-mac-address;
 	};

arch/arm/boot/dts/omap3-sbc-t3517.dts

@@ -0,0 +1,43 @@
+/*
+ * Suppport for CompuLab SBC-T3517 with CM-T3517
+ */
+
+#include "omap3-cm-t3517.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+	model = "CompuLab SBC-T3517 with CM-T3517";
+	compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&sb_t35_usb_hub_pins
+			&usb_hub_pins
+		    >;
+
+	mmc1_aux_pins: pinmux_mmc1_aux_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20c0, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_clk.gpio_59   */
+			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_cts.gpio_144 */
+		>;
+	};
+
+	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21ec, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_98 - SB-T35 USB HUB RST */
+		>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&mmc1_pins
+		&mmc1_aux_pins
+	>;
+
+	wp-gpios =  <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio_59  */
+	cd-gpios =  <&gpio5 16 GPIO_ACTIVE_HIGH>; /* gpio_144 */
+};

arch/arm/boot/dts/omap3-sbc-t3530.dts

@@ -0,0 +1,36 @@
+/*
+ * Suppport for CompuLab SBC-T3530 with CM-T3530
+ */
+
+#include "omap3-cm-t3530.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+	model = "CompuLab SBC-T3530 with CM-T3530";
+	compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sb_t35_usb_hub_pins>;
+
+	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
+		>;
+	};
+};
+
+/*
+ * The following ranges correspond to SMSC9x eth chips on CM-T3530 CoM and
+ * SB-T35 baseboard respectively.
+ * This setting includes both chips in SBC-T3530 board device tree.
+ */
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>,
+		 <4 0 0x2d000000 0x01000000>;
+};
+
+&mmc1 {
+	cd-gpios =  <&twl_gpio 0 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/omap3-sbc-t3730.dts

@@ -10,21 +10,18 @@
 	compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
 };
 
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sb_t35_usb_hub_pins>;
+
+	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
+		>;
+	};
+};
+
 &gpmc {
 	ranges = <5 0 0x2c000000 0x01000000>,
 		 <4 0 0x2d000000 0x01000000>;
 };
-
-&smsc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&smsc2_pins>;
-};
-
-&omap3_pmx_core {
-	smsc2_pins: pinmux_smsc2_pins {
-		pinctrl-single,pins = <
-			0x86 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs4.gpmc_ncs4 */
-			0xa2 (PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
-		>;
-	};
-};

arch/arm/boot/dts/omap3.dtsi

@@ -35,6 +35,11 @@
 			compatible = "arm,cortex-a8";
 			device_type = "cpu";
 			reg = <0x0>;
+
+			clocks = <&dpll1_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
 
@@ -411,10 +416,19 @@
 		};
 
 		mmu_isp: mmu@480bd400 {
-			compatible = "ti,omap3-mmu-isp";
+			compatible = "ti,omap2-iommu";
-			ti,hwmods = "mmu_isp";
 			reg = <0x480bd400 0x80>;
-			interrupts = <8>;
+			interrupts = <24>;
+			ti,hwmods = "mmu_isp";
+			ti,#tlb-entries = <8>;
+		};
+
+		mmu_iva: mmu@5d000000 {
+			compatible = "ti,omap2-iommu";
+			reg = <0x5d000000 0x80>;
+			interrupts = <28>;
+			ti,hwmods = "mmu_iva";
+			status = "disabled";
 		};
 
 		wdt2: wdt@48314000 {
@@ -436,6 +450,7 @@
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@49022000 {
@@ -453,6 +468,7 @@
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@49024000 {
@@ -470,6 +486,7 @@
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp4: mcbsp@49026000 {
@@ -485,6 +502,7 @@
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp5: mcbsp@48096000 {
@@ -500,6 +518,7 @@
 			dmas = <&sdma 21>,
 			       <&sdma 22>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		sham: sham@480c3000 {
@@ -634,14 +653,14 @@
 			ranges;
 
 			usbhsohci: ohci@48064400 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x48064400 0x400>;
 				interrupt-parent = <&intc>;
 				interrupts = <76>;
 			};
 
 			usbhsehci: ehci@48064800 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x48064800 0x400>;
 				interrupt-parent = <&intc>;
 				interrupts = <77>;
@@ -669,6 +688,58 @@
 			num-eps = <16>;
 			ram-bits = <12>;
 		};
+
+		dss: dss@48050000 {
+			compatible = "ti,omap3-dss";
+			reg = <0x48050000 0x200>;
+			status = "disabled";
+			ti,hwmods = "dss_core";
+			clocks = <&dss1_alwon_fck>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			dispc@48050400 {
+				compatible = "ti,omap3-dispc";
+				reg = <0x48050400 0x400>;
+				interrupts = <25>;
+				ti,hwmods = "dss_dispc";
+				clocks = <&dss1_alwon_fck>;
+				clock-names = "fck";
+			};
+
+			dsi: encoder@4804fc00 {
+				compatible = "ti,omap3-dsi";
+				reg = <0x4804fc00 0x200>,
+				      <0x4804fe00 0x40>,
+				      <0x4804ff00 0x20>;
+				reg-names = "proto", "phy", "pll";
+				interrupts = <25>;
+				status = "disabled";
+				ti,hwmods = "dss_dsi1";
+				clocks = <&dss1_alwon_fck>, <&dss2_alwon_fck>;
+				clock-names = "fck", "sys_clk";
+			};
+
+			rfbi: encoder@48050800 {
+				compatible = "ti,omap3-rfbi";
+				reg = <0x48050800 0x100>;
+				status = "disabled";
+				ti,hwmods = "dss_rfbi";
+				clocks = <&dss1_alwon_fck>, <&dss_ick>;
+				clock-names = "fck", "ick";
+			};
+
+			venc: encoder@48050c00 {
+				compatible = "ti,omap3-venc";
+				reg = <0x48050c00 0x100>;
+				status = "disabled";
+				ti,hwmods = "dss_venc";
+				clocks = <&dss_tv_fck>;
+				clock-names = "fck";
+			};
+		};
 	};
 };
 

arch/arm/boot/dts/omap3430-sdp.dts

@@ -34,6 +34,10 @@
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
 	vmmc_aux-supply = <&vsim>;
+	/*
+	 * S6-3 must be in ON position for 8 bit mode to function
+	 * Else, use 4 bit mode
+	 */
 	bus-width = <8>;
 };
 
@@ -103,9 +107,8 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <1 0 0x08000000>;
+		ti,nand-ecc-opt = "ham1";
 		nand-bus-width = <8>;
-
-		ti,nand-ecc-opt = "sw";
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <36>;
 		gpmc,cs-wr-off-ns = <36>;

arch/arm/boot/dts/omap3430es1-clocks.dtsi

@@ -82,16 +82,16 @@
 		ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
 	};
 
-	ssi_ssr_fck_3430es1: ssi_ssr_fck_3430es1 {
+	ssi_ssr_fck: ssi_ssr_fck_3430es1 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&ssi_ssr_gate_fck_3430es1>, <&ssi_ssr_div_fck_3430es1>;
 	};
 
-	ssi_sst_fck_3430es1: ssi_sst_fck_3430es1 {
+	ssi_sst_fck: ssi_sst_fck_3430es1 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
-		clocks = <&ssi_ssr_fck_3430es1>;
+		clocks = <&ssi_ssr_fck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
@@ -120,7 +120,7 @@
 		clock-div = <1>;
 	};
 
-	ssi_ick_3430es1: ssi_ick_3430es1 {
+	ssi_ick: ssi_ick_3430es1 {
 		#clock-cells = <0>;
 		compatible = "ti,omap3-no-wait-interface-clock";
 		clocks = <&ssi_l4_ick>;
@@ -152,7 +152,7 @@
 		clocks = <&usb_l4_gate_ick>, <&usb_l4_div_ick>;
 	};
 
-	dss1_alwon_fck_3430es1: dss1_alwon_fck_3430es1 {
+	dss1_alwon_fck: dss1_alwon_fck_3430es1 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
 		clocks = <&dpll4_m4x2_ck>;
@@ -161,7 +161,7 @@
 		ti,set-rate-parent;
 	};
 
-	dss_ick_3430es1: dss_ick_3430es1 {
+	dss_ick: dss_ick_3430es1 {
 		#clock-cells = <0>;
 		compatible = "ti,omap3-no-wait-interface-clock";
 		clocks = <&l4_ick>;
@@ -184,7 +184,7 @@
 	dss_clkdm: dss_clkdm {
 		compatible = "ti,clockdomain";
 		clocks = <&dss_tv_fck>, <&dss_96m_fck>, <&dss2_alwon_fck>,
-			 <&dss1_alwon_fck_3430es1>, <&dss_ick_3430es1>;
+			 <&dss1_alwon_fck>, <&dss_ick>;
 	};
 
 	d2d_clkdm: d2d_clkdm {
@@ -203,6 +203,6 @@
 			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
 			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
 			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>,
-			 <&fshostusb_fck>, <&fac_ick>, <&ssi_ick_3430es1>;
+			 <&fshostusb_fck>, <&fac_ick>, <&ssi_ick>;
 	};
 };

arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi

@@ -160,7 +160,7 @@
 		ti,bit-shift = <30>;
 	};
 
-	dss1_alwon_fck_3430es2: dss1_alwon_fck_3430es2 {
+	dss1_alwon_fck: dss1_alwon_fck_3430es2 {
 		#clock-cells = <0>;
 		compatible = "ti,dss-gate-clock";
 		clocks = <&dpll4_m4x2_ck>;
@@ -169,7 +169,7 @@
 		ti,set-rate-parent;
 	};
 
-	dss_ick_3430es2: dss_ick_3430es2 {
+	dss_ick: dss_ick_3430es2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap3-dss-interface-clock";
 		clocks = <&l4_ick>;
@@ -216,7 +216,7 @@
 	dss_clkdm: dss_clkdm {
 		compatible = "ti,clockdomain";
 		clocks = <&dss_tv_fck>, <&dss_96m_fck>, <&dss2_alwon_fck>,
-			 <&dss1_alwon_fck_3430es2>, <&dss_ick_3430es2>;
+			 <&dss1_alwon_fck>, <&dss_ick>;
 	};
 
 	core_l4_clkdm: core_l4_clkdm {

arch/arm/boot/dts/omap36xx-clocks.dtsi

@@ -70,6 +70,26 @@
 	};
 };
 
+&dpll4_m2x2_mul_ck {
+	clock-mult = <1>;
+};
+
+&dpll4_m3x2_mul_ck {
+	clock-mult = <1>;
+};
+
+&dpll4_m4x2_mul_ck {
+	ti,clock-mult = <1>;
+};
+
+&dpll4_m5x2_mul_ck {
+	clock-mult = <1>;
+};
+
+&dpll4_m6x2_mul_ck {
+	clock-mult = <1>;
+};
+
 &cm_clockdomains {
 	dpll4_clkdm: dpll4_clkdm {
 		compatible = "ti,clockdomain";

arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi

@@ -25,16 +25,16 @@
 		ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
 	};
 
-	ssi_ssr_fck_3430es2: ssi_ssr_fck_3430es2 {
+	ssi_ssr_fck: ssi_ssr_fck_3430es2 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&ssi_ssr_gate_fck_3430es2>, <&ssi_ssr_div_fck_3430es2>;
 	};
 
-	ssi_sst_fck_3430es2: ssi_sst_fck_3430es2 {
+	ssi_sst_fck: ssi_sst_fck_3430es2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
-		clocks = <&ssi_ssr_fck_3430es2>;
+		clocks = <&ssi_ssr_fck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
@@ -55,7 +55,7 @@
 		clock-div = <1>;
 	};
 
-	ssi_ick_3430es2: ssi_ick_3430es2 {
+	ssi_ick: ssi_ick_3430es2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap3-ssi-interface-clock";
 		clocks = <&ssi_l4_ick>;
@@ -193,6 +193,6 @@
 			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
 			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
 			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>,
-			 <&ssi_ick_3430es2>;
+			 <&ssi_ick>;
 	};
 };

arch/arm/boot/dts/omap36xx.dtsi

@@ -39,6 +39,26 @@
 			clock-frequency = <48000000>;
 		};
 
+		abb_mpu_iva: regulator-abb-mpu {
+			compatible = "ti,abb-v1";
+			regulator-name = "abb_mpu_iva";
+			#address-cell = <0>;
+			#size-cells = <0>;
+			reg = <0x483072f0 0x8>, <0x48306818 0x4>;
+			reg-names = "base-address", "int-address";
+			ti,tranxdone-status-mask = <0x4000000>;
+			clocks = <&sys_ck>;
+			ti,settling-time = <30>;
+			ti,clock-cycles = <8>;
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m	fbb_m	vset_m*/
+			1012500		0	0	0	0	0
+			1200000		0	0	0	0	0
+			1325000		0	0	0	0	0
+			1375000		1	0	0	0	0
+			>;
+		};
+
 		omap3_pmx_core2: pinmux@480025a0 {
 			compatible = "ti,omap3-padconf", "pinctrl-single";
 			reg = <0x480025a0 0x5c>;
@@ -52,7 +72,13 @@
 	};
 };
 
-/include/ "omap36xx-clocks.dtsi"
+/* OMAP3630 needs dss_96m_fck for VENC */
+&venc {
+	clocks = <&dss_tv_fck>, <&dss_96m_fck>;
+	clock-names = "fck", "tv_dac_clk";
+};
+
 /include/ "omap34xx-omap36xx-clocks.dtsi"
 /include/ "omap36xx-omap3430es2plus-clocks.dtsi"
 /include/ "omap36xx-am35xx-omap3430es2plus-clocks.dtsi"
+/include/ "omap36xx-clocks.dtsi"

arch/arm/boot/dts/omap3xxx-clocks.dtsi

@@ -425,10 +425,11 @@
 
 	dpll4_m4x2_mul_ck: dpll4_m4x2_mul_ck {
 		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
+		compatible = "ti,fixed-factor-clock";
 		clocks = <&dpll4_m4_ck>;
-		clock-mult = <2>;
+		ti,clock-mult = <2>;
-		clock-div = <1>;
+		ti,clock-div = <1>;
+		ti,set-rate-parent;
 	};
 
 	dpll4_m4x2_ck: dpll4_m4x2_ck {
@@ -438,6 +439,7 @@
 		ti,bit-shift = <0x1d>;
 		reg = <0x0d00>;
 		ti,set-bit-to-disable;
+		ti,set-rate-parent;
 	};
 
 	dpll4_m5_ck: dpll4_m5_ck {

arch/arm/boot/dts/omap4-duovero-parlor.dts

@@ -0,0 +1,146 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap4-duovero.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "OMAP4430 Gumstix Duovero on Parlor";
+	compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
+
+	leds {
+		compatible = "gpio-leds";
+		led0 {
+			label = "duovero:blue:led0";
+			gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;	/* gpio_122 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		button0@121 {
+			label = "button0";
+			linux,code = <BTN_0>;
+			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;	/* gpio_121 */
+			gpio-key,wakeup;
+		};
+	};
+};
+
+&omap4_pmx_core {
+	pinctrl-0 = <
+			&led_pins
+			&button_pins
+			&smsc_pins
+	>;
+
+	led_pins: pinmux_led_pins {
+		pinctrl-single,pins = <
+			0xd6 (PIN_OUTPUT | MUX_MODE3)		/* abe_dmic_din3.gpio_122 */
+		>;
+	};
+
+	button_pins: pinmux_button_pins {
+		pinctrl-single,pins = <
+			0xd4 (PIN_INPUT_PULLUP | MUX_MODE3)	/* abe_dmic_din2.gpio_121 */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0xe6 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_scl */
+			0xe8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0xea (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
+			0xec (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
+		>;
+	};
+
+	smsc_pins: pinmux_smsc_pins {
+		pinctrl-single,pins = <
+			0x28 (PIN_INPUT | MUX_MODE3)		/* gpmc_a20.gpio_44: IRQ */
+			0x2a (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a21.gpio_45: nReset */
+			0x30 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a24.gpio_48: amdix enabled */
+		>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
+	clock-frequency = <100000>;
+
+	/* optional 1K EEPROM with revision information */
+	eeprom@51 {
+		compatible = "atmel,24c01";
+		reg = <0x51>;
+		pagesize = <8>;
+	};
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+#include "omap-gpmc-smsc911x.dtsi"
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x1000000>;			/* CS5 */
+
+	ethernet@gpmc {
+		reg = <5 0 0xff>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;		/* gpio_44 */
+
+		phy-mode = "mii";
+
+		gpmc,cs-on-ns = <10>;
+		gpmc,cs-rd-off-ns = <50>;
+		gpmc,cs-wr-off-ns = <50>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <10>;
+		gpmc,adv-wr-off-ns = <10>;
+		gpmc,oe-on-ns = <15>;
+		gpmc,oe-off-ns = <50>;
+		gpmc,we-on-ns = <15>;
+		gpmc,we-off-ns = <50>;
+		gpmc,rd-cycle-ns = <50>;
+		gpmc,wr-cycle-ns = <50>;
+		gpmc,access-ns = <50>;
+		gpmc,page-burst-access-ns = <0>;
+		gpmc,bus-turnaround-ns = <35>;
+		gpmc,cycle2cycle-delay-ns = <35>;
+		gpmc,wr-data-mux-bus-ns = <35>;
+		gpmc,wr-access-ns = <50>;
+
+		gpmc,mux-add-data = <2>;
+		gpmc,sync-read;
+		gpmc,sync-write;
+		gpmc,clk-activation-ns = <5>;
+		gpmc,sync-clk-ps = <20000>;
+	};
+};
+
+

arch/arm/boot/dts/omap4-duovero.dtsi

@@ -0,0 +1,252 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "omap443x.dtsi"
+
+/ {
+	model = "Gumstix Duovero";
+	compatible = "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+
+	sound {
+		compatible = "ti,abe-twl6040";
+		ti,model = "DuoVero";
+
+		ti,mclk-freq = <38400000>;
+
+		ti,mcpdm = <&mcpdm>;
+
+		ti,twl6040 = <&twl6040>;
+
+		/* Audio routing */
+		ti,audio-routing =
+			"Headset Stereophone", "HSOL",
+			"Headset Stereophone", "HSOR",
+			"HSMIC", "Headset Mic",
+			"Headset Mic", "Headset Mic Bias";
+	};
+
+	/* HS USB Host PHY on PORT 1 */
+	hsusb1_phy: hsusb1_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;	/* gpio_62 */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hsusb1phy_pins>;
+
+		clocks = <&auxclk3_ck>;
+		clock-names = "main_clk";
+		clock-frequency = <19200000>;
+	};
+
+	/* regulator for w2cbw0015 on sdio5 */
+	w2cbw0015_vmmc: w2cbw0015_vmmc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&w2cbw0015_pins>;
+		compatible = "regulator-fixed";
+		regulator-name = "w2cbw0015";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio2 11 GPIO_ACTIVE_LOW>;		/* gpio_43 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&omap4_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&twl6040_pins
+			&mcpdm_pins
+			&mcbsp1_pins
+			&hsusbb1_pins
+	>;
+
+	twl6040_pins: pinmux_twl6040_pins {
+		pinctrl-single,pins = <
+			0x126 (PIN_OUTPUT | MUX_MODE3)		/* usbb2_ulpitll_nxt.gpio_160 */
+			0x160 (PIN_INPUT | MUX_MODE0)		/* sys_nirq2.sys_nirq2 */
+		>;
+	};
+
+	mcpdm_pins: pinmux_mcpdm_pins {
+		pinctrl-single,pins = <
+			0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_pdm_ul_data.abe_pdm_ul_data */
+			0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_pdm_dl_data.abe_pdm_dl_data */
+			0xca (PIN_INPUT_PULLUP   | MUX_MODE0)	/* abe_pdm_frame.abe_pdm_frame */
+			0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_pdm_lb_clk.abe_pdm_lb_clk */
+			0xce (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_clks.abe_clks */
+		>;
+	};
+
+	mcbsp1_pins: pinmux_mcbsp1_pins {
+		pinctrl-single,pins = <
+			0xbe (PIN_INPUT | MUX_MODE0)		/* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
+			0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_mcbsp1_dr.abe_mcbsp1_dr */
+			0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* abe_mcbsp1_dx.abe_mcbsp1_dx */
+			0xc4 (PIN_INPUT | MUX_MODE0)		/* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
+		>;
+	};
+
+	hsusbb1_pins: pinmux_hsusbb1_pins {
+		pinctrl-single,pins = <
+			0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
+			0x84 (PIN_OUTPUT | MUX_MODE4)		/* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
+			0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
+			0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
+			0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
+			0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
+			0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
+			0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
+			0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
+			0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
+			0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
+			0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
+		>;
+	};
+
+	hsusb1phy_pins: pinmux_hsusb1phy_pins {
+		pinctrl-single,pins = <
+			0x4c (PIN_OUTPUT | MUX_MODE3)		/* gpmc_wait1.gpio_62 */
+		>;
+	};
+
+	w2cbw0015_pins: pinmux_w2cbw0015_pins {
+		pinctrl-single,pins = <
+			0x26 (PIN_OUTPUT | MUX_MODE3)		/* gpmc_a19.gpio_43 */
+			0x3a (PIN_INPUT | MUX_MODE3)		/* gpmc_ncs3.gpio_53 */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0xe2 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
+			0xe4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
+		>;
+	};
+
+	i2c4_pins: pinmux_i2c4_pins {
+		pinctrl-single,pins = <
+			0xee (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_scl */
+			0xf0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0xa2 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk */
+			0xa4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmcc1_cmd */
+			0xa6 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmcc1_dat0 */
+			0xa8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1 */
+			0xaa (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2 */
+			0xac (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3 */
+		>;
+	};
+
+	mmc5_pins: pinmux_mmc5_pins {
+		pinctrl-single,pins = <
+			0x108 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_clk */
+			0x10a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmcc5_cmd */
+			0x10c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmcc5_dat0 */
+			0x10e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat1 */
+			0x110 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat2 */
+			0x112 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat3 */
+		>;
+	};
+};
+
+/* PMIC */
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	clock-frequency = <400000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;		/* IRQ_SYS_1N cascaded to gic */
+		interrupt-parent = <&gic>;
+	};
+
+	twl6040: twl@4b {
+		compatible = "ti,twl6040";
+		reg = <0x4b>;
+		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;		/* IRQ_SYS_2N cascaded to gic */
+		interrupt-parent = <&gic>;
+		ti,audpwron-gpio = <&gpio6 0 GPIO_ACTIVE_HIGH>;		/* gpio_160 */
+
+		vio-supply = <&v1v8>;
+		v2v1-supply = <&v2v1>;
+		enable-active-high;
+	};
+};
+
+#include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
+
+/* on-board bluetooth / WiFi module */
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+
+	clock-frequency = <400000>;
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+
+	vmmc-supply = <&vmmc>;
+	ti,bus-width = <4>;
+	ti,non-removable;		/* FIXME: use PMIC_MMC detect */
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+/* mmc3 is available to the expansion board */
+
+&mmc4 {
+	status = "disabled";
+};
+
+/* on-board WiFi module */
+&mmc5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc5_pins>;
+
+	vmmc-supply = <&w2cbw0015_vmmc>;
+	ti,bus-width = <4>;
+	ti,non-removable;
+	cap-power-off-card;
+};
+
+&twl_usb_comparator {
+	usb-supply = <&vusb>;
+};
+
+&usb_otg_hs {
+	interface-type = <1>;
+	mode = <3>;
+	power = <50>;
+};
+
+&usbhshost {
+	port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy>;
+};
+

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -16,6 +16,11 @@
 		reg = <0x80000000 0x40000000>; /* 1 GB */
 	};
 
+	aliases {
+		display0 = &dvi0;
+		display1 = &hdmi0;
+	};
+
 	leds: leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -83,12 +88,8 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
 		vcc-supply = <&hsusb1_power>;
-	/**
+		clocks = <&auxclk3_ck>;
-	 * FIXME:
+		clock-names = "main_clk";
-	 * put the right clock phandle here when available
-	 *	clocks = <&auxclk3>;
-	 *	clock-names = "main_clk";
-	 */
 		clock-frequency = <19200000>;
 	};
 
@@ -104,14 +105,94 @@
 		startup-delay-us = <70000>;
 		enable-active-high;
 	};
+
+	tfp410: encoder@0 {
+		compatible = "ti,tfp410";
+		powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;	/* gpio_0 */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tfp410_in: endpoint@0 {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tfp410_out: endpoint@0 {
+					remote-endpoint = <&dvi_connector_in>;
+				};
+			};
+		};
+	};
+
+	dvi0: connector@0 {
+		compatible = "dvi-connector";
+		label = "dvi";
+
+		digital;
+
+		ddc-i2c-bus = <&i2c3>;
+
+		port {
+			dvi_connector_in: endpoint {
+				remote-endpoint = <&tfp410_out>;
+			};
+		};
+	};
+
+	tpd12s015: encoder@1 {
+		compatible = "ti,tpd12s015";
+
+		gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>,	/* 60, CT CP HPD */
+			<&gpio2 9 GPIO_ACTIVE_HIGH>,	/* 41, LS OE */
+			<&gpio2 31 GPIO_ACTIVE_HIGH>;	/* 63, HPD */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tpd12s015_in: endpoint@0 {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tpd12s015_out: endpoint@0 {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
+	hdmi0: connector@1 {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tpd12s015_out>;
+			};
+		};
+	};
 };
 
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&twl6040_pins
-			&mcpdm_pins
-			&mcbsp1_pins
 			&dss_dpi_pins
 			&tfp410_pins
 			&dss_hdmi_pins
@@ -300,6 +381,10 @@
 	twl6040: twl@4b {
 		compatible = "ti,twl6040";
 		reg = <0x4b>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&twl6040_pins>;
+
 		/* IRQ# = 119 */
 		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
 		interrupt-parent = <&gic>;
@@ -380,16 +465,16 @@
 	device-handle = <&elpida_ECB240ABACN>;
 };
 
-&mcbsp2 {
+&mcbsp1 {
-	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp1_pins>;
+	status = "okay";
 };
 
-&mcbsp3 {
+&mcpdm {
-	status = "disabled";
+	pinctrl-names = "default";
-};
+	pinctrl-0 = <&mcpdm_pins>;
-
+	status = "okay";
-&dmic {
-	status = "disabled";
 };
 
 &twl_usb_comparator {
@@ -409,3 +494,30 @@
 &usbhsehci {
 	phys = <&hsusb1_phy>;
 };
+
+&dss {
+	status = "ok";
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&tfp410_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+&dsi2 {
+	status = "ok";
+	vdd-supply = <&vcxio>;
+};
+
+&hdmi {
+	status = "ok";
+	vdda-supply = <&vdac>;
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&tpd12s015_in>;
+		};
+	};
+};

arch/arm/boot/dts/omap4-sdp.dts

@@ -19,6 +19,12 @@
 		reg = <0x80000000 0x40000000>; /* 1 GB */
 	};
 
+	aliases {
+		display0 = &lcd0;
+		display1 = &lcd1;
+		display2 = &hdmi0;
+	};
+
 	vdd_eth: fixedregulator-vdd-eth {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_ETH";
@@ -153,16 +159,53 @@
 		startup-delay-us = <70000>;
 		enable-active-high;
 	};
+
+	tpd12s015: encoder@0 {
+		compatible = "ti,tpd12s015";
+
+		gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>,	/* 60, CT CP HPD */
+			<&gpio2 9 GPIO_ACTIVE_HIGH>,	/* 41, LS OE */
+			<&gpio2 31 GPIO_ACTIVE_HIGH>;	/* 63, HPD */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tpd12s015_in: endpoint@0 {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tpd12s015_out: endpoint@0 {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
+	hdmi0: connector@0 {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "c";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tpd12s015_out>;
+			};
+		};
+	};
 };
 
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&twl6040_pins
-			&mcpdm_pins
-			&dmic_pins
-			&mcbsp1_pins
-			&mcbsp2_pins
 			&dss_hdmi_pins
 			&tpd12s015_pins
 	>;
@@ -326,6 +369,10 @@
 	twl6040: twl@4b {
 		compatible = "ti,twl6040";
 		reg = <0x4b>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&twl6040_pins>;
+
 		/* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
 		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
 		interrupt-parent = <&gic>;
@@ -537,8 +584,28 @@
 	pinctrl-0 = <&uart4_pins>;
 };
 
-&mcbsp3 {
+&mcbsp1 {
-	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp1_pins>;
+	status = "okay";
+};
+
+&mcbsp2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
+	status = "okay";
+};
+
+&dmic {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dmic_pins>;
+	status = "okay";
+};
+
+&mcpdm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcpdm_pins>;
+	status = "okay";
 };
 
 &twl_usb_comparator {
@@ -550,3 +617,68 @@
 	mode = <3>;
 	power = <50>;
 };
+
+&dss {
+	status = "ok";
+};
+
+&dsi1 {
+	status = "ok";
+	vdd-supply = <&vcxio>;
+
+	port {
+		dsi1_out_ep: endpoint {
+			remote-endpoint = <&lcd0_in>;
+			lanes = <0 1 2 3 4 5>;
+		};
+	};
+
+	lcd0: display {
+		compatible = "tpo,taal", "panel-dsi-cm";
+		label = "lcd0";
+
+		reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;	/* 102 */
+
+		port {
+			lcd0_in: endpoint {
+				remote-endpoint = <&dsi1_out_ep>;
+			};
+		};
+	};
+};
+
+&dsi2 {
+	status = "ok";
+	vdd-supply = <&vcxio>;
+
+	port {
+		dsi2_out_ep: endpoint {
+			remote-endpoint = <&lcd1_in>;
+			lanes = <0 1 2 3 4 5>;
+		};
+	};
+
+	lcd1: display {
+		compatible = "tpo,taal", "panel-dsi-cm";
+		label = "lcd1";
+
+		reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;	/* 104 */
+
+		port {
+			lcd1_in: endpoint {
+				remote-endpoint = <&dsi2_out_ep>;
+			};
+		};
+	};
+};
+
+&hdmi {
+	status = "ok";
+	vdda-supply = <&vdac>;
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&tpd12s015_in>;
+		};
+	};
+};

arch/arm/boot/dts/omap4.dtsi

@@ -36,6 +36,11 @@
 			device_type = "cpu";
 			next-level-cache = <&L2>;
 			reg = <0x0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 		cpu@1 {
 			compatible = "arm,cortex-a9";
@@ -313,6 +318,7 @@
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x4a0f6000 0x1000>;
 			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
 		};
 
 		i2c1: i2c@48070000 {
@@ -461,6 +467,21 @@
 			dma-names = "tx", "rx";
 		};
 
+		mmu_dsp: mmu@4a066000 {
+			compatible = "ti,omap4-iommu";
+			reg = <0x4a066000 0x100>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmu_dsp";
+		};
+
+		mmu_ipu: mmu@55082000 {
+			compatible = "ti,omap4-iommu";
+			reg = <0x55082000 0x100>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmu_ipu";
+			ti,iommu-bus-err-back;
+		};
+
 		wdt2: wdt@4a314000 {
 			compatible = "ti,omap4-wdt", "ti,omap3-wdt";
 			reg = <0x4a314000 0x80>;
@@ -478,6 +499,7 @@
 			dmas = <&sdma 65>,
 			       <&sdma 66>;
 			dma-names = "up_link", "dn_link";
+			status = "disabled";
 		};
 
 		dmic: dmic@4012e000 {
@@ -489,6 +511,7 @@
 			ti,hwmods = "dmic";
 			dmas = <&sdma 67>;
 			dma-names = "up_link";
+			status = "disabled";
 		};
 
 		mcbsp1: mcbsp@40122000 {
@@ -503,6 +526,7 @@
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@40124000 {
@@ -517,6 +541,7 @@
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@40126000 {
@@ -531,6 +556,7 @@
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp4: mcbsp@48096000 {
@@ -544,6 +570,7 @@
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		keypad: keypad@4a31c000 {
@@ -554,6 +581,13 @@
 			ti,hwmods = "kbd";
 		};
 
+		dmm@4e000000 {
+			compatible = "ti,omap4-dmm";
+			reg = <0x4e000000 0x800>;
+			interrupts = <0 113 0x4>;
+			ti,hwmods = "dmm";
+		};
+
 		emif1: emif@4c000000 {
 			compatible = "ti,emif-4d";
 			reg = <0x4c000000 0x100>;
@@ -699,14 +733,14 @@
 			ranges;
 
 			usbhsohci: ohci@4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci@4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
@@ -757,6 +791,111 @@
 			dmas = <&sdma 117>, <&sdma 116>;
 			dma-names = "tx", "rx";
 		};
+
+		abb_mpu: regulator-abb-mpu {
+			compatible = "ti,abb-v2";
+			regulator-name = "abb_mpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			ti,tranxdone-status-mask = <0x80>;
+			clocks = <&sys_clkin_ck>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			status = "disabled";
+		};
+
+		abb_iva: regulator-abb-iva {
+			compatible = "ti,abb-v2";
+			regulator-name = "abb_iva";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			ti,tranxdone-status-mask = <0x80000000>;
+			clocks = <&sys_clkin_ck>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			status = "disabled";
+		};
+
+		dss: dss@58000000 {
+			compatible = "ti,omap4-dss";
+			reg = <0x58000000 0x80>;
+			status = "disabled";
+			ti,hwmods = "dss_core";
+			clocks = <&dss_dss_clk>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			dispc@58001000 {
+				compatible = "ti,omap4-dispc";
+				reg = <0x58001000 0x1000>;
+				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+				ti,hwmods = "dss_dispc";
+				clocks = <&dss_dss_clk>;
+				clock-names = "fck";
+			};
+
+			rfbi: encoder@58002000  {
+				compatible = "ti,omap4-rfbi";
+				reg = <0x58002000 0x1000>;
+				status = "disabled";
+				ti,hwmods = "dss_rfbi";
+				clocks = <&dss_dss_clk>, <&dss_fck>;
+				clock-names = "fck", "ick";
+			};
+
+			venc: encoder@58003000 {
+				compatible = "ti,omap4-venc";
+				reg = <0x58003000 0x1000>;
+				status = "disabled";
+				ti,hwmods = "dss_venc";
+				clocks = <&dss_tv_clk>;
+				clock-names = "fck";
+			};
+
+			dsi1: encoder@58004000 {
+				compatible = "ti,omap4-dsi";
+				reg = <0x58004000 0x200>,
+				      <0x58004200 0x40>,
+				      <0x58004300 0x20>;
+				reg-names = "proto", "phy", "pll";
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+				ti,hwmods = "dss_dsi1";
+				clocks = <&dss_dss_clk>, <&dss_sys_clk>;
+				clock-names = "fck", "sys_clk";
+			};
+
+			dsi2: encoder@58005000 {
+				compatible = "ti,omap4-dsi";
+				reg = <0x58005000 0x200>,
+				      <0x58005200 0x40>,
+				      <0x58005300 0x20>;
+				reg-names = "proto", "phy", "pll";
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+				ti,hwmods = "dss_dsi2";
+				clocks = <&dss_dss_clk>, <&dss_sys_clk>;
+				clock-names = "fck", "sys_clk";
+			};
+
+			hdmi: encoder@58006000 {
+				compatible = "ti,omap4-hdmi";
+				reg = <0x58006000 0x200>,
+				      <0x58006200 0x100>,
+				      <0x58006300 0x100>,
+				      <0x58006400 0x1000>;
+				reg-names = "wp", "pll", "phy", "core";
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+				ti,hwmods = "dss_hdmi";
+				clocks = <&dss_48mhz_clk>, <&dss_sys_clk>;
+				clock-names = "fck", "sys_clk";
+			};
+		};
 	};
 };
 

arch/arm/boot/dts/omap443x.dtsi

@@ -43,6 +43,32 @@
 			#thermal-sensor-cells = <0>;
 		};
 	};
+
+	ocp {
+		abb_mpu: regulator-abb-mpu {
+			status = "okay";
+
+			reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>;
+			reg-names = "base-address", "int-address";
+
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m	fbb_m	vset_m*/
+			1025000		0	0	0	0	0
+			1200000		0	0	0	0	0
+			1313000		0	0	0	0	0
+			1375000		1	0	0	0	0
+			1389000		1	0	0	0	0
+			>;
+		};
+
+		/* Default unused, just provide register info for record */
+		abb_iva: regulator-abb-iva {
+			reg = <0x4a307bd8 0x8>, <0x4a306010 0x4>;
+			reg-names = "base-address", "int-address";
+		};
+
+	};
+
 };
 
 /include/ "omap443x-clocks.dtsi"

arch/arm/boot/dts/omap4460.dtsi

@@ -50,7 +50,44 @@
 
 			#thermal-sensor-cells = <0>;
 		};
+
+		abb_mpu: regulator-abb-mpu {
+			status = "okay";
+
+			reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>,
+			      <0x4A002268 0x4>;
+			reg-names = "base-address", "int-address",
+				    "efuse-address";
+
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m	fbb_m	vset_m*/
+			1025000		0	0	0	0	0
+			1200000		0	0	0	0	0
+			1313000		0	0	0x100000 0x40000 0
+			1375000		1	0	0	0	0
+			1389000		1	0	0	0	0
+			>;
+		};
+
+		abb_iva: regulator-abb-iva {
+			status = "okay";
+
+			reg = <0x4a307bd8 0x8>, <0x4a306010 0x4>,
+			      <0x4A002268 0x4>;
+			reg-names = "base-address", "int-address",
+				    "efuse-address";
+
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m	fbb_m	vset_m*/
+			950000		0	0	0	0	0
+			1140000		0	0	0	0	0
+			1291000		0	0	0x200000 0	0
+			1375000		1	0	0	0	0
+			1376000		1	0	0	0	0
+			>;
+		};
 	};
+
 };
 
 /include/ "omap446x-clocks.dtsi"

arch/arm/boot/dts/omap5-uevm.dts

@@ -31,12 +31,8 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
-	/**
+		clocks = <&auxclk1_ck>;
-	  * FIXME
+		clock-names = "main_clk";
-	  * Put the right clock phandle here when available
-	  *	clocks = <&auxclk1>;
-	  *	clock-names = "main_clk";
-	  */
 		clock-frequency = <19200000>;
 	};
 

arch/arm/boot/dts/omap5.dtsi

@@ -49,6 +49,12 @@
 				1000000 1060000
 				1500000 1250000
 			>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+
 			/* cooling options */
 			cooling-min-level = <0>;
 			cooling-max-level = <2>;
@@ -353,6 +359,7 @@
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x4a0f6000 0x1000>;
 			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
 		};
 
 		mcspi1: spi@48098000 {
@@ -513,6 +520,21 @@
 			dma-names = "tx", "rx";
 		};
 
+		mmu_dsp: mmu@4a066000 {
+			compatible = "ti,omap4-iommu";
+			reg = <0x4a066000 0x100>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmu_dsp";
+		};
+
+		mmu_ipu: mmu@55082000 {
+			compatible = "ti,omap4-iommu";
+			reg = <0x55082000 0x100>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmu_ipu";
+			ti,iommu-bus-err-back;
+		};
+
 		keypad: keypad@4ae1c000 {
 			compatible = "ti,omap4-keypad";
 			reg = <0x4ae1c000 0x400>;
@@ -529,6 +551,7 @@
 			dmas = <&sdma 65>,
 			       <&sdma 66>;
 			dma-names = "up_link", "dn_link";
+			status = "disabled";
 		};
 
 		dmic: dmic@4012e000 {
@@ -540,6 +563,7 @@
 			ti,hwmods = "dmic";
 			dmas = <&sdma 67>;
 			dma-names = "up_link";
+			status = "disabled";
 		};
 
 		mcbsp1: mcbsp@40122000 {
@@ -554,6 +578,7 @@
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@40124000 {
@@ -568,6 +593,7 @@
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@40126000 {
@@ -582,6 +608,7 @@
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		timer1: timer@4ae18000 {
@@ -683,6 +710,13 @@
 			ti,hwmods = "wd_timer2";
 		};
 
+		dmm@4e000000 {
+			compatible = "ti,omap5-dmm";
+			reg = <0x4e000000 0x800>;
+			interrupts = <0 113 0x4>;
+			ti,hwmods = "dmm";
+		};
+
 		emif1: emif@4c000000 {
 			compatible	= "ti,emif-4d5";
 			ti,hwmods	= "emif1";
@@ -732,7 +766,8 @@
 				compatible = "snps,dwc3";
 				reg = <0x4a030000 0x10000>;
 				interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
-				usb-phy = <&usb2_phy>, <&usb3_phy>;
+				phys = <&usb2_phy>, <&usb3_phy>;
+				phy-names = "usb2-phy", "usb3-phy";
 				dr_mode = "peripheral";
 				tx-fifo-resize;
 			};
@@ -749,6 +784,7 @@
 				compatible = "ti,omap-usb2";
 				reg = <0x4a084000 0x7c>;
 				ctrl-module = <&omap_control_usb2phy>;
+				#phy-cells = <0>;
 			};
 
 			usb3_phy: usb3phy@4a084400 {
@@ -758,6 +794,7 @@
 				      <0x4a084c00 0x40>;
 				reg-names = "phy_rx", "phy_tx", "pll_ctrl";
 				ctrl-module = <&omap_control_usb3phy>;
+				#phy-cells = <0>;
 			};
 		};
 
@@ -777,14 +814,14 @@
 			ranges;
 
 			usbhsohci: ohci@4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci@4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/boot/dts/tps65910.dtsi

@@ -82,5 +82,10 @@
 			reg = <12>;
 			regulator-compatible = "vmmc";
 		};
+
+		vbb_reg: regulator@13 {
+			reg = <13>;
+			regulator-compatible = "vbb";
+		};
 	};
 };

arch/arm/boot/dts/twl4030.dtsi

@@ -145,4 +145,11 @@
 		compatible = "ti,twl4030-pwrbutton";
 		interrupts = <8>;
 	};
+
+	twl_keypad: keypad {
+		compatible = "ti,twl4030-keypad";
+		interrupts = <1>;
+		keypad,num-rows = <8>;
+		keypad,num-columns = <8>;
+	};
 };

arch/arm/mach-omap2/clockdomains3xxx_data.c

@@ -247,7 +247,7 @@ static struct clockdomain neon_clkdm = {
 static struct clockdomain iva2_clkdm = {
 	.name		= "iva2_clkdm",
 	.pwrdm		= { .name = "iva2_pwrdm" },
-	.flags		= CLKDM_CAN_HWSUP_SWSUP,
+	.flags		= CLKDM_CAN_SWSUP,
 	.dep_bit	= OMAP3430_PM_WKDEP_MPU_EN_IVA2_SHIFT,
 	.wkdep_srcs	= iva2_wkdeps,
 	.clktrctrl_mask = OMAP3430_CLKTRCTRL_IVA2_MASK,

arch/arm/mach-omap2/devices.c

@@ -229,6 +229,9 @@ static struct omap_iommu_arch_data omap3_isp_iommu = {
 
 int omap3_init_camera(struct isp_platform_data *pdata)
 {
+	if (of_have_populated_dt())
+		omap3_isp_iommu.name = "480bd400.mmu";
+
 	omap3isp_device.dev.platform_data = pdata;
 	omap3isp_device.dev.archdata.iommu = &omap3_isp_iommu;
 

arch/arm/mach-omap2/gpmc-nand.c

@@ -45,24 +45,31 @@ static struct platform_device gpmc_nand_device = {
 
 static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
 {
-	/* support only OMAP3 class */
+	/* platforms which support all ECC schemes */
-	if (!cpu_is_omap34xx() && !soc_is_am33xx()) {
+	if (soc_is_am33xx() || cpu_is_omap44xx() ||
-		pr_err("BCH ecc is not supported on this CPU\n");
+		 soc_is_omap54xx() || soc_is_dra7xx())
+		return 1;
+
+	/* OMAP3xxx do not have ELM engine, so cannot support ECC schemes
+	 * which require H/W based ECC error detection */
+	if ((cpu_is_omap34xx() || cpu_is_omap3630()) &&
+	    ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) ||
+		 (ecc_opt == OMAP_ECC_BCH8_CODE_HW)))
 		return 0;
-	}
 
 	/*
 	 * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1
 	 * and AM33xx derivates. Other chips may be added if confirmed to work.
 	 */
-	if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) &&
+	if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW_DETECTION_SW) &&
-	    (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)) &&
+	    (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)))
-	    (!soc_is_am33xx())) {
-		pr_err("BCH 4-bit mode is not supported on this CPU\n");
 		return 0;
-	}
 
-	return 1;
+	/* legacy platforms support only HAM1 (1-bit Hamming) ECC scheme */
+	if (ecc_opt == OMAP_ECC_HAM1_CODE_HW)
+		return 1;
+	else
+		return 0;
 }
 
 /* This function will go away once the device-tree convertion is complete */
@@ -133,8 +140,10 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 
 	gpmc_update_nand_reg(&gpmc_nand_data->reg, gpmc_nand_data->cs);
 
-	if (!gpmc_hwecc_bch_capable(gpmc_nand_data->ecc_opt))
+	if (!gpmc_hwecc_bch_capable(gpmc_nand_data->ecc_opt)) {
+		dev_err(dev, "Unsupported NAND ECC scheme selected\n");
 		return -EINVAL;
+	}
 
 	err = platform_device_register(&gpmc_nand_device);
 	if (err < 0) {

arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

@@ -3029,8 +3029,6 @@ static struct omap_hwmod omap3xxx_mmu_isp_hwmod = {
 	.flags		= HWMOD_NO_IDLEST,
 };
 
-#ifdef CONFIG_OMAP_IOMMU_IVA2
-
 /* mmu iva */
 
 static struct omap_mmu_dev_attr mmu_iva_dev_attr = {
@@ -3070,20 +3068,22 @@ static struct omap_hwmod omap3xxx_mmu_iva_hwmod = {
 	.name		= "mmu_iva",
 	.class		= &omap3xxx_mmu_hwmod_class,
 	.mpu_irqs	= omap3xxx_mmu_iva_irqs,
+	.clkdm_name	= "iva2_clkdm",
 	.rst_lines	= omap3xxx_mmu_iva_resets,
 	.rst_lines_cnt	= ARRAY_SIZE(omap3xxx_mmu_iva_resets),
 	.main_clk	= "iva2_ck",
 	.prcm = {
 		.omap2 = {
 			.module_offs = OMAP3430_IVA2_MOD,
+			.module_bit = OMAP3430_CM_FCLKEN_IVA2_EN_IVA2_SHIFT,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP3430_ST_IVA2_SHIFT,
 		},
 	},
 	.dev_attr	= &mmu_iva_dev_attr,
 	.flags		= HWMOD_NO_IDLEST,
 };
 
-#endif
-
 /* l4_per -> gpio4 */
 static struct omap_hwmod_addr_space omap3xxx_gpio4_addrs[] = {
 	{
@@ -3855,9 +3855,7 @@ static struct omap_hwmod_ocp_if *omap34xx_hwmod_ocp_ifs[] __initdata = {
 	&omap3xxx_l4_core__hdq1w,
 	&omap3xxx_sad2d__l3,
 	&omap3xxx_l4_core__mmu_isp,
-#ifdef CONFIG_OMAP_IOMMU_IVA2
 	&omap3xxx_l3_main__mmu_iva,
-#endif
 	&omap34xx_l4_core__ssi,
 	NULL
 };
@@ -3881,9 +3879,7 @@ static struct omap_hwmod_ocp_if *omap36xx_hwmod_ocp_ifs[] __initdata = {
 	&omap3xxx_l4_core__hdq1w,
 	&omap3xxx_sad2d__l3,
 	&omap3xxx_l4_core__mmu_isp,
-#ifdef CONFIG_OMAP_IOMMU_IVA2
 	&omap3xxx_l3_main__mmu_iva,
-#endif
 	NULL
 };
 

arch/arm/mach-omap2/omap_hwmod_54xx_data.c

@@ -1121,6 +1121,71 @@ static struct omap_hwmod omap54xx_mmc5_hwmod = {
 	},
 };
 
+/*
+ * 'mmu' class
+ * The memory management unit performs virtual to physical address translation
+ * for its requestors.
+ */
+
+static struct omap_hwmod_class_sysconfig omap54xx_mmu_sysc = {
+	.rev_offs	= 0x0000,
+	.sysc_offs	= 0x0010,
+	.syss_offs	= 0x0014,
+	.sysc_flags	= (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY |
+			   SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET |
+			   SYSS_HAS_RESET_STATUS),
+	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
+	.sysc_fields	= &omap_hwmod_sysc_type1,
+};
+
+static struct omap_hwmod_class omap54xx_mmu_hwmod_class = {
+	.name = "mmu",
+	.sysc = &omap54xx_mmu_sysc,
+};
+
+static struct omap_hwmod_rst_info omap54xx_mmu_dsp_resets[] = {
+	{ .name = "mmu_cache", .rst_shift = 1 },
+};
+
+static struct omap_hwmod omap54xx_mmu_dsp_hwmod = {
+	.name		= "mmu_dsp",
+	.class		= &omap54xx_mmu_hwmod_class,
+	.clkdm_name	= "dsp_clkdm",
+	.rst_lines	= omap54xx_mmu_dsp_resets,
+	.rst_lines_cnt	= ARRAY_SIZE(omap54xx_mmu_dsp_resets),
+	.main_clk	= "dpll_iva_h11x2_ck",
+	.prcm = {
+		.omap4 = {
+			.clkctrl_offs = OMAP54XX_CM_DSP_DSP_CLKCTRL_OFFSET,
+			.rstctrl_offs = OMAP54XX_RM_DSP_RSTCTRL_OFFSET,
+			.context_offs = OMAP54XX_RM_DSP_DSP_CONTEXT_OFFSET,
+			.modulemode   = MODULEMODE_HWCTRL,
+		},
+	},
+};
+
+/* mmu ipu */
+static struct omap_hwmod_rst_info omap54xx_mmu_ipu_resets[] = {
+	{ .name = "mmu_cache", .rst_shift = 2 },
+};
+
+static struct omap_hwmod omap54xx_mmu_ipu_hwmod = {
+	.name		= "mmu_ipu",
+	.class		= &omap54xx_mmu_hwmod_class,
+	.clkdm_name	= "ipu_clkdm",
+	.rst_lines	= omap54xx_mmu_ipu_resets,
+	.rst_lines_cnt	= ARRAY_SIZE(omap54xx_mmu_ipu_resets),
+	.main_clk	= "dpll_core_h22x2_ck",
+	.prcm = {
+		.omap4 = {
+			.clkctrl_offs = OMAP54XX_CM_IPU_IPU_CLKCTRL_OFFSET,
+			.rstctrl_offs = OMAP54XX_RM_IPU_RSTCTRL_OFFSET,
+			.context_offs = OMAP54XX_RM_IPU_IPU_CONTEXT_OFFSET,
+			.modulemode   = MODULEMODE_HWCTRL,
+		},
+	},
+};
+
 /*
  * 'mpu' class
  * mpu sub-system
@@ -1763,6 +1828,14 @@ static struct omap_hwmod_ocp_if omap54xx_l4_cfg__l3_main_1 = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
+/* l4_cfg -> mmu_dsp */
+static struct omap_hwmod_ocp_if omap54xx_l4_cfg__mmu_dsp = {
+	.master		= &omap54xx_l4_cfg_hwmod,
+	.slave		= &omap54xx_mmu_dsp_hwmod,
+	.clk		= "l4_root_clk_div",
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
 /* mpu -> l3_main_1 */
 static struct omap_hwmod_ocp_if omap54xx_mpu__l3_main_1 = {
 	.master		= &omap54xx_mpu_hwmod,
@@ -1787,6 +1860,14 @@ static struct omap_hwmod_ocp_if omap54xx_l4_cfg__l3_main_2 = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
+/* l3_main_2 -> mmu_ipu */
+static struct omap_hwmod_ocp_if omap54xx_l3_main_2__mmu_ipu = {
+	.master		= &omap54xx_l3_main_2_hwmod,
+	.slave		= &omap54xx_mmu_ipu_hwmod,
+	.clk		= "l3_iclk_div",
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
 /* l3_main_1 -> l3_main_3 */
 static struct omap_hwmod_ocp_if omap54xx_l3_main_1__l3_main_3 = {
 	.master		= &omap54xx_l3_main_1_hwmod,
@@ -2345,6 +2426,7 @@ static struct omap_hwmod_ocp_if *omap54xx_hwmod_ocp_ifs[] __initdata = {
 	&omap54xx_l4_wkup__counter_32k,
 	&omap54xx_l4_cfg__dma_system,
 	&omap54xx_l4_abe__dmic,
+	&omap54xx_l4_cfg__mmu_dsp,
 	&omap54xx_mpu__emif1,
 	&omap54xx_mpu__emif2,
 	&omap54xx_l4_wkup__gpio1,
@@ -2360,6 +2442,7 @@ static struct omap_hwmod_ocp_if *omap54xx_hwmod_ocp_ifs[] __initdata = {
 	&omap54xx_l4_per__i2c3,
 	&omap54xx_l4_per__i2c4,
 	&omap54xx_l4_per__i2c5,
+	&omap54xx_l3_main_2__mmu_ipu,
 	&omap54xx_l4_wkup__kbd,
 	&omap54xx_l4_cfg__mailbox,
 	&omap54xx_l4_abe__mcbsp1,

arch/arm/mach-omap2/pdata-quirks.c

@@ -16,12 +16,14 @@
 #include <linux/wl12xx.h>
 
 #include <linux/platform_data/pinctrl-single.h>
+#include <linux/platform_data/iommu-omap.h>
 
 #include "am35xx.h"
 #include "common.h"
 #include "common-board-devices.h"
 #include "dss-common.h"
 #include "control.h"
+#include "omap_device.h"
 
 struct pdata_init {
 	const char *compatible;
@@ -31,20 +33,6 @@ struct pdata_init {
 struct of_dev_auxdata omap_auxdata_lookup[];
 static struct twl4030_gpio_platform_data twl_gpio_auxdata;
 
-/*
- * Create alias for USB host PHY clock.
- * Remove this when clock phandle can be provided via DT
- */
-static void __init __used legacy_init_ehci_clk(char *clkname)
-{
-	int ret;
-
-	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
-	if (ret)
-		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
-		       __func__, clkname, ret);
-}
-
 #if IS_ENABLED(CONFIG_WL12XX)
 
 static struct wl12xx_platform_data wl12xx __initdata;
@@ -92,6 +80,12 @@ static void __init hsmmc2_internal_input_clk(void)
 	omap_ctrl_writel(reg, OMAP343X_CONTROL_DEVCONF1);
 }
 
+static struct iommu_platform_data omap3_iommu_pdata = {
+	.reset_name = "mmu",
+	.assert_reset = omap_device_assert_hardreset,
+	.deassert_reset = omap_device_deassert_hardreset,
+};
+
 static int omap3_sbc_t3730_twl_callback(struct device *dev,
 					   unsigned gpio,
 					   unsigned ngpio)
@@ -99,7 +93,7 @@ static int omap3_sbc_t3730_twl_callback(struct device *dev,
 	int res;
 
 	res = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
-			       "wlan rst");
+			       "wlan pwr");
 	if (res)
 		return res;
 
@@ -108,6 +102,23 @@ static int omap3_sbc_t3730_twl_callback(struct device *dev,
 	return 0;
 }
 
+static void __init omap3_sbc_t3x_usb_hub_init(int gpio, char *hub_name)
+{
+	int err = gpio_request_one(gpio, GPIOF_OUT_INIT_LOW, hub_name);
+
+	if (err) {
+		pr_err("SBC-T3x: %s reset gpio request failed: %d\n",
+			hub_name, err);
+		return;
+	}
+
+	gpio_export(gpio, 0);
+
+	udelay(10);
+	gpio_set_value(gpio, 1);
+	msleep(1);
+}
+
 static void __init omap3_sbc_t3730_twl_init(void)
 {
 	twl_gpio_auxdata.setup = omap3_sbc_t3730_twl_callback;
@@ -115,10 +126,17 @@ static void __init omap3_sbc_t3730_twl_init(void)
 
 static void __init omap3_sbc_t3730_legacy_init(void)
 {
+	omap3_sbc_t3x_usb_hub_init(167, "sb-t35 usb hub");
 	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 136);
 	omap_ads7846_init(1, 57, 0, NULL);
 }
 
+static void __init omap3_sbc_t3530_legacy_init(void)
+{
+	omap3_sbc_t3x_usb_hub_init(167, "sb-t35 usb hub");
+	omap_ads7846_init(1, 57, 0, NULL);
+}
+
 static void __init omap3_igep0020_legacy_init(void)
 {
 	omap3_igep2_display_init_of();
@@ -160,7 +178,7 @@ static struct emac_platform_data am35xx_emac_pdata = {
 	.interrupt_disable	= am35xx_disable_emac_int,
 };
 
-static void __init am3517_evm_legacy_init(void)
+static void __init am35xx_emac_reset(void)
 {
 	u32 v;
 
@@ -169,6 +187,43 @@ static void __init am3517_evm_legacy_init(void)
 	omap_ctrl_writel(v, AM35XX_CONTROL_IP_SW_RESET);
 	omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); /* OCP barrier */
 }
+
+static struct gpio cm_t3517_wlan_gpios[] __initdata = {
+	{ 56,	GPIOF_OUT_INIT_HIGH,	"wlan pwr" },
+	{ 4,	GPIOF_OUT_INIT_HIGH,	"xcvr noe" },
+};
+
+static void __init omap3_sbc_t3517_wifi_init(void)
+{
+	int err = gpio_request_array(cm_t3517_wlan_gpios,
+				ARRAY_SIZE(cm_t3517_wlan_gpios));
+	if (err) {
+		pr_err("SBC-T3517: wl12xx gpios request failed: %d\n", err);
+		return;
+	}
+
+	gpio_export(cm_t3517_wlan_gpios[0].gpio, 0);
+	gpio_export(cm_t3517_wlan_gpios[1].gpio, 0);
+
+	msleep(100);
+	gpio_set_value(cm_t3517_wlan_gpios[1].gpio, 0);
+}
+
+static void __init omap3_sbc_t3517_legacy_init(void)
+{
+	omap3_sbc_t3x_usb_hub_init(152, "cm-t3517 usb hub");
+	omap3_sbc_t3x_usb_hub_init(98, "sb-t35 usb hub");
+	am35xx_emac_reset();
+	hsmmc2_internal_input_clk();
+	omap3_sbc_t3517_wifi_init();
+	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 145);
+	omap_ads7846_init(1, 57, 0, NULL);
+}
+
+static void __init am3517_evm_legacy_init(void)
+{
+	am35xx_emac_reset();
+}
 #endif /* CONFIG_ARCH_OMAP3 */
 
 #ifdef CONFIG_ARCH_OMAP4
@@ -182,15 +237,28 @@ static void __init omap4_sdp_legacy_init(void)
 static void __init omap4_panda_legacy_init(void)
 {
 	omap4_panda_display_init_of();
-	legacy_init_ehci_clk("auxclk3_ck");
 	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
 }
 #endif
 
+#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
+static struct iommu_platform_data omap4_iommu_pdata = {
+	.reset_name = "mmu_cache",
+	.assert_reset = omap_device_assert_hardreset,
+	.deassert_reset = omap_device_deassert_hardreset,
+};
+#endif
+
+#ifdef CONFIG_SOC_AM33XX
+static void __init am335x_evmsk_legacy_init(void)
+{
+	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 31);
+}
+#endif
+
 #ifdef CONFIG_SOC_OMAP5
 static void __init omap5_uevm_legacy_init(void)
 {
-	legacy_init_ehci_clk("auxclk1_ck");
 }
 #endif
 
@@ -240,6 +308,8 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
 #ifdef CONFIG_ARCH_OMAP3
 	OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002030, "48002030.pinmux", &pcs_pdata),
 	OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002a00, "48002a00.pinmux", &pcs_pdata),
+	OF_DEV_AUXDATA("ti,omap2-iommu", 0x5d000000, "5d000000.mmu",
+		       &omap3_iommu_pdata),
 	/* Only on am3517 */
 	OF_DEV_AUXDATA("ti,davinci_mdio", 0x5c030000, "davinci_mdio.0", NULL),
 	OF_DEV_AUXDATA("ti,am3517-emac", 0x5c000000, "davinci_emac.0",
@@ -248,6 +318,12 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
 #ifdef CONFIG_ARCH_OMAP4
 	OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a100040, "4a100040.pinmux", &pcs_pdata),
 	OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a31e040, "4a31e040.pinmux", &pcs_pdata),
+#endif
+#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
+	OF_DEV_AUXDATA("ti,omap4-iommu", 0x4a066000, "4a066000.mmu",
+		       &omap4_iommu_pdata),
+	OF_DEV_AUXDATA("ti,omap4-iommu", 0x55082000, "55082000.mmu",
+		       &omap4_iommu_pdata),
 #endif
 	{ /* sentinel */ },
 };
@@ -258,6 +334,8 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
  */
 static struct pdata_init pdata_quirks[] __initdata = {
 #ifdef CONFIG_ARCH_OMAP3
+	{ "compulab,omap3-sbc-t3517", omap3_sbc_t3517_legacy_init, },
+	{ "compulab,omap3-sbc-t3530", omap3_sbc_t3530_legacy_init, },
 	{ "compulab,omap3-sbc-t3730", omap3_sbc_t3730_legacy_init, },
 	{ "nokia,omap3-n900", hsmmc2_internal_input_clk, },
 	{ "nokia,omap3-n9", hsmmc2_internal_input_clk, },
@@ -271,6 +349,9 @@ static struct pdata_init pdata_quirks[] __initdata = {
 	{ "ti,omap4-sdp", omap4_sdp_legacy_init, },
 	{ "ti,omap4-panda", omap4_panda_legacy_init, },
 #endif
+#ifdef CONFIG_SOC_AM33XX
+	{ "ti,am335x-evmsk", am335x_evmsk_legacy_init, },
+#endif
 #ifdef CONFIG_SOC_OMAP5
 	{ "ti,omap5-uevm", omap5_uevm_legacy_init, },
 #endif

arch/arm/plat-omap/Kconfig

@@ -86,9 +86,6 @@ config OMAP_MUX_WARNINGS
 	  to change the pin multiplexing setup.	 When there are no warnings
 	  printed, it's safe to deselect OMAP_MUX for your product.
 
-config OMAP_IOMMU_IVA2
-	bool
-
 config OMAP_MPU_TIMER
 	bool "Use mpu timer"
 	depends on ARCH_OMAP1

include/dt-bindings/pinctrl/am43xx.h

@@ -13,6 +13,7 @@
 #define MUX_MODE5	5
 #define MUX_MODE6	6
 #define MUX_MODE7	7
+#define MUX_MODE8	8
 
 #define PULL_DISABLE		(1 << 16)
 #define PULL_UP			(1 << 17)