korg/linux
0
0
Fork 0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-12-13 05:54:23 +08:00
Code Issues Packages Projects Releases Wiki Activity

dt-bindings: iio: adc: Add docs for AD7606 ADC

Browse Source 
Document support for AD7606 Analog to Digital Converter.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit is contained in:
Stefan Popa 2018-12-17 14:23:40 +02:00 committed by Jonathan Cameron
parent 2985a5d884
commit 6e33a125df
2 changed files with 66 additions and 0 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

65
Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt Normal file
View File

@ -0,0 +1,65 @@
Analog Devices AD7606 Simultaneous Sampling ADC
Required properties for the AD7606:
- compatible: Must be one of
* "adi,ad7605-4"
* "adi,ad7606-8"
* "adi,ad7606-6"
* "adi,ad7606-4"
- reg: SPI chip select number for the device
- spi-max-frequency: Max SPI frequency to use
see: Documentation/devicetree/bindings/spi/spi-bus.txt
- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
- avcc-supply: phandle to the Avcc power supply
- interrupts: IRQ line for the ADC
see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
This logic input is used to initiate conversions on the analog
input channels. As the line is active high, it should be marked
GPIO_ACTIVE_HIGH.
Optional properties:
- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
it will be asserted during driver probe. As the line is active high,
it should be marked GPIO_ACTIVE_HIGH.
- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
to place the AD7606 into one of two power-down modes, Standby mode or
Shutdown mode. As the line is active low, it should be marked
GPIO_ACTIVE_LOW.
- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
The FRSTDATA output indicates when the first channel, V1, is
being read back on either the parallel, byte or serial interface.
As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
this pin determines the input range of the analog input channels. If
this pin is tied to a logic high, the analog input range is ±10V for
all channels. If this pin is tied to a logic low, the analog input range
is ±5V for all channels. As the line is active high, it should be marked
GPIO_ACTIVE_HIGH.
- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling
mode pins. As the line is active high, it should be marked
GPIO_ACTIVE_HIGH.
Example:
adc@0 {
compatible = "adi,ad7606-8";
reg = <0>;
spi-max-frequency = <1000000>;
spi-cpol;
avcc-supply = <&adc_vref>;
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
interrupt-parent = <&gpio>;
adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
&gpio 23 GPIO_ACTIVE_HIGH
&gpio 26 GPIO_ACTIVE_HIGH>;
standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
};

1
MAINTAINERS
View File

@ -860,6 +860,7 @@ L: linux-iio@vger.kernel.org
W: http://ez.analog.com/community/linux-device-drivers
S: Supported
F: drivers/iio/adc/ad7606.c
F: Documentation/devicetree/bindings/iio/adc/ad7606.txt
ANALOG DEVICES INC AD9389B DRIVER
M: Hans Verkuil <hans.verkuil@cisco.com>