mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-23 12:14:10 +08:00
i2c: testunit: add SMBusAlert trigger
To test SMBusAlert handlers, let the testunit be able to trigger SMBusAlert interrupts. This new command needs a GPIO connected to the SMBAlert# line. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
This commit is contained in:
Wolfram Sang
parent
06e12ae5f0
commit
3d16973f77
@ -185,3 +185,51 @@ default response::
|
||||
|
||||
# i2cset -y 0 0x30 4 0 0 i; i2cget -y 0 0x30
|
||||
0x00
|
||||
|
||||
0x05 SMBUS_ALERT_REQUEST
|
||||
~~~~~~~~~~~~~~~~~~~~~~~~
|
||||
|
||||
.. list-table::
|
||||
:header-rows: 1
|
||||
|
||||
* - CMD
|
||||
- DATAL
|
||||
- DATAH
|
||||
- DELAY
|
||||
|
||||
* - 0x05
|
||||
- response value (7 MSBs interpreted as I2C address)
|
||||
- currently unused
|
||||
- n * 10ms
|
||||
|
||||
This test raises an interrupt via the SMBAlert pin which the host controller
|
||||
must handle. The pin must be connected to the testunit as a GPIO. GPIO access
|
||||
is not allowed to sleep. Currently, this can only be described using firmware
|
||||
nodes. So, for devicetree, you would add something like this to the testunit
|
||||
node::
|
||||
|
||||
gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
|
||||
|
||||
The following command will trigger the alert with a response of 0xc9 after 1
|
||||
second of delay::
|
||||
|
||||
# i2cset -y 0 0x30 5 0xc9 0x00 100 i
|
||||
|
||||
If the host controller supports SMBusAlert, this message with debug level
|
||||
should appear::
|
||||
|
||||
smbus_alert 0-000c: SMBALERT# from dev 0x64, flag 1
|
||||
|
||||
This message may appear more than once because the testunit is software not
|
||||
hardware and, thus, may not be able to react to the response of the host fast
|
||||
enough. The interrupt count should increase only by one, though::
|
||||
|
||||
# cat /proc/interrupts | grep smbus_alert
|
||||
93: 1 gpio-rcar 26 Edge smbus_alert
|
||||
|
||||
If the host does not respond to the alert within 1 second, the test will be
|
||||
aborted and the testunit will report an error.
|
||||
|
||||
For this test, the testunit will shortly drop its assigned address and listen
|
||||
on the SMBus Alert Response Address (0x0c). It will reassign its original
|
||||
address afterwards.
|
||||
|
||||
@ -8,6 +8,8 @@
|
||||
|
||||
#include <generated/utsrelease.h>
|
||||
#include <linux/bitops.h>
|
||||
#include <linux/completion.h>
|
||||
#include <linux/gpio/consumer.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/module.h>
|
||||
@ -22,6 +24,7 @@ enum testunit_cmds {
|
||||
TU_CMD_SMBUS_HOST_NOTIFY,
|
||||
TU_CMD_SMBUS_BLOCK_PROC_CALL,
|
||||
TU_CMD_GET_VERSION_WITH_REP_START,
|
||||
TU_CMD_SMBUS_ALERT_REQUEST,
|
||||
TU_NUM_CMDS
|
||||
};
|
||||
|
||||
@ -44,10 +47,37 @@ struct testunit_data {
|
||||
u8 read_idx;
|
||||
struct i2c_client *client;
|
||||
struct delayed_work worker;
|
||||
struct gpio_desc *gpio;
|
||||
struct completion alert_done;
|
||||
};
|
||||
|
||||
static char tu_version_info[] = "v" UTS_RELEASE "\n\0";
|
||||
|
||||
static int i2c_slave_testunit_smbalert_cb(struct i2c_client *client,
|
||||
enum i2c_slave_event event, u8 *val)
|
||||
{
|
||||
struct testunit_data *tu = i2c_get_clientdata(client);
|
||||
|
||||
switch (event) {
|
||||
case I2C_SLAVE_READ_PROCESSED:
|
||||
gpiod_set_value(tu->gpio, 0);
|
||||
fallthrough;
|
||||
case I2C_SLAVE_READ_REQUESTED:
|
||||
*val = tu->regs[TU_REG_DATAL];
|
||||
break;
|
||||
|
||||
case I2C_SLAVE_STOP:
|
||||
complete(&tu->alert_done);
|
||||
break;
|
||||
|
||||
case I2C_SLAVE_WRITE_REQUESTED:
|
||||
case I2C_SLAVE_WRITE_RECEIVED:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int i2c_slave_testunit_slave_cb(struct i2c_client *client,
|
||||
enum i2c_slave_event event, u8 *val)
|
||||
{
|
||||
@ -127,8 +157,10 @@ static int i2c_slave_testunit_slave_cb(struct i2c_client *client,
|
||||
static void i2c_slave_testunit_work(struct work_struct *work)
|
||||
{
|
||||
struct testunit_data *tu = container_of(work, struct testunit_data, worker.work);
|
||||
unsigned long time_left;
|
||||
struct i2c_msg msg;
|
||||
u8 msgbuf[256];
|
||||
u16 orig_addr;
|
||||
int ret = 0;
|
||||
|
||||
msg.addr = I2C_CLIENT_END;
|
||||
@ -150,6 +182,26 @@ static void i2c_slave_testunit_work(struct work_struct *work)
|
||||
msgbuf[2] = tu->regs[TU_REG_DATAH];
|
||||
break;
|
||||
|
||||
case TU_CMD_SMBUS_ALERT_REQUEST:
|
||||
i2c_slave_unregister(tu->client);
|
||||
orig_addr = tu->client->addr;
|
||||
tu->client->addr = 0x0c;
|
||||
ret = i2c_slave_register(tu->client, i2c_slave_testunit_smbalert_cb);
|
||||
if (ret)
|
||||
goto out_smbalert;
|
||||
|
||||
reinit_completion(&tu->alert_done);
|
||||
gpiod_set_value(tu->gpio, 1);
|
||||
time_left = wait_for_completion_timeout(&tu->alert_done, HZ);
|
||||
if (!time_left)
|
||||
ret = -ETIMEDOUT;
|
||||
|
||||
i2c_slave_unregister(tu->client);
|
||||
out_smbalert:
|
||||
tu->client->addr = orig_addr;
|
||||
i2c_slave_register(tu->client, i2c_slave_testunit_slave_cb);
|
||||
break;
|
||||
|
||||
default:
|
||||
break;
|
||||
}
|
||||
@ -176,8 +228,15 @@ static int i2c_slave_testunit_probe(struct i2c_client *client)
|
||||
|
||||
tu->client = client;
|
||||
i2c_set_clientdata(client, tu);
|
||||
init_completion(&tu->alert_done);
|
||||
INIT_DELAYED_WORK(&tu->worker, i2c_slave_testunit_work);
|
||||
|
||||
tu->gpio = devm_gpiod_get_index_optional(&client->dev, NULL, 0, GPIOD_OUT_LOW);
|
||||
if (gpiod_cansleep(tu->gpio)) {
|
||||
dev_err(&client->dev, "GPIO access which may sleep is not allowed\n");
|
||||
return -EDEADLK;
|
||||
}
|
||||
|
||||
if (sizeof(tu_version_info) > TU_VERSION_MAX_LENGTH)
|
||||
tu_version_info[TU_VERSION_MAX_LENGTH - 1] = 0;
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user