diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index f53e2ee65e35..6cf680ed8290 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -175,6 +175,9 @@ Boards: - AM5728 IDK compatible = "ti,am5728-idk", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" +- AM5718 IDK + compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index f61c48704f2d..6447abce6fde 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -605,6 +605,7 @@ dtb-$(CONFIG_SOC_DRA7XX) += \ am57xx-cl-som-am57x.dtb \ am57xx-sbc-am57x.dtb \ am572x-idk.dtb \ + am571x-idk.dtb \ dra7-evm.dtb \ dra72-evm.dtb \ dra72-evm-revc.dtb \ diff --git a/arch/arm/boot/dts/am335x-baltos-ir2110.dts b/arch/arm/boot/dts/am335x-baltos-ir2110.dts index a9a97307d66c..501c7527121b 100644 --- a/arch/arm/boot/dts/am335x-baltos-ir2110.dts +++ b/arch/arm/boot/dts/am335x-baltos-ir2110.dts @@ -54,16 +54,22 @@ dr_mode = "host"; }; +&davinci_mdio { + phy0: ethernet-phy@0 { + reg = <1>; + }; +}; + &cpsw_emac0 { - phy_id = <&davinci_mdio>, <1>; phy-mode = "rmii"; dual_emac_res_vlan = <1>; + phy-handle = <&phy0>; }; &cpsw_emac1 { - phy_id = <&davinci_mdio>, <7>; phy-mode = "rgmii-txid"; dual_emac_res_vlan = <2>; + phy-handle = <&phy1>; }; &phy_sel { diff --git a/arch/arm/boot/dts/am335x-baltos-ir3220.dts b/arch/arm/boot/dts/am335x-baltos-ir3220.dts index fe002a17c04b..19f53b8569e1 100644 --- a/arch/arm/boot/dts/am335x-baltos-ir3220.dts +++ b/arch/arm/boot/dts/am335x-baltos-ir3220.dts @@ -109,9 +109,9 @@ }; &cpsw_emac1 { - phy_id = <&davinci_mdio>, <7>; phy-mode = "rgmii-txid"; dual_emac_res_vlan = <2>; + phy-handle = <&phy1>; }; &phy_sel { diff --git a/arch/arm/boot/dts/am335x-baltos-ir5221.dts b/arch/arm/boot/dts/am335x-baltos-ir5221.dts index f599350dd305..2b9d7f4db23f 100644 --- a/arch/arm/boot/dts/am335x-baltos-ir5221.dts +++ b/arch/arm/boot/dts/am335x-baltos-ir5221.dts @@ -127,9 +127,9 @@ }; &cpsw_emac1 { - phy_id = <&davinci_mdio>, <7>; phy-mode = "rgmii-txid"; dual_emac_res_vlan = <2>; + phy-handle = <&phy1>; }; &phy_sel { diff --git a/arch/arm/boot/dts/am335x-baltos.dtsi b/arch/arm/boot/dts/am335x-baltos.dtsi index 09b954154e6b..efb5eae290a8 100644 --- a/arch/arm/boot/dts/am335x-baltos.dtsi +++ b/arch/arm/boot/dts/am335x-baltos.dtsi @@ -364,11 +364,14 @@ }; &davinci_mdio { + status = "okay"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&davinci_mdio_default>; pinctrl-1 = <&davinci_mdio_sleep>; - status = "okay"; + phy1: ethernet-phy@1 { + reg = <7>; + }; }; &mmc1 { diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index 6bbb1fee0868..db00d8ef7b19 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -79,6 +79,14 @@ &lcdc { status = "okay"; + + /* If you want to get 24 bit RGB and 16 BGR mode instead of + * current 16 bit RGB and 24 BGR modes, set the propety + * below to "crossed" and uncomment the video-ports -property + * in tda19988 node. + */ + blue-and-red-wiring = "straight"; + port { lcdc_0: endpoint@0 { remote-endpoint = <&hdmi_0>; @@ -95,6 +103,9 @@ pinctrl-0 = <&nxp_hdmi_bonelt_pins>; pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */ + /* video-ports = <0x234501>; */ + #sound-dai-cells = <0>; audio-ports = < TDA998x_I2S 0x03>; diff --git a/arch/arm/boot/dts/am335x-icev2.dts b/arch/arm/boot/dts/am335x-icev2.dts index 85e04c205542..1463df3b5b19 100644 --- a/arch/arm/boot/dts/am335x-icev2.dts +++ b/arch/arm/boot/dts/am335x-icev2.dts @@ -43,52 +43,52 @@ enable-active-high; }; - leds0 { + leds-iio { + status = "disabled"; compatible = "gpio-leds"; - - led0 { + led-out0 { label = "out0"; gpios = <&tpic2810 0 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led1 { + led-out1 { label = "out1"; gpios = <&tpic2810 1 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led2 { + led-out2 { label = "out2"; gpios = <&tpic2810 2 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led3 { + led-out3 { label = "out3"; gpios = <&tpic2810 3 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led4 { + led-out4 { label = "out4"; gpios = <&tpic2810 4 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led5 { + led-out5 { label = "out5"; gpios = <&tpic2810 5 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led6 { + led-out6 { label = "out6"; gpios = <&tpic2810 6 GPIO_ACTIVE_HIGH>; default-state = "off"; }; - led7 { + led-out7 { label = "out7"; gpios = <&tpic2810 7 GPIO_ACTIVE_HIGH>; default-state = "off"; @@ -187,6 +187,8 @@ AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0) /* (B17) spi0_d0.spi0_d0 */ AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* (B16) spi0_d1.spi0_d1 */ AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0) /* (A16) spi0_cs0.spi0_cs0 */ + AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE0) /* (C15) spi0_cs1.spi0_cs1 */ + AM33XX_IOPAD(0x9a0, PIN_INPUT_PULLUP | MUX_MODE7) /* (B12) mcasp0_aclkr.gpio3[18] */ >; }; @@ -224,6 +226,31 @@ }; }; +&spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_default>; + + sn65hvs882@1 { + compatible = "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + load-gpios = <&gpio3 18 GPIO_ACTIVE_LOW>; + + reg = <1>; + spi-max-frequency = <1000000>; + spi-cpol; + }; +}; + +&tscadc { + status = "okay"; + adc { + ti,adc-channels = <1 2 3 4 5 6 7>; + }; +}; + #include "tps65910.dtsi" &tps { diff --git a/arch/arm/boot/dts/am437x-idk-evm.dts b/arch/arm/boot/dts/am437x-idk-evm.dts index 25ce611c6568..b76a7c0264a5 100644 --- a/arch/arm/boot/dts/am437x-idk-evm.dts +++ b/arch/arm/boot/dts/am437x-idk-evm.dts @@ -117,6 +117,58 @@ compatible = "fixed-clock"; clock-frequency = <32768>; }; + + leds-iio { + status = "disabled"; + compatible = "gpio-leds"; + led-out0 { + label = "out0"; + gpios = <&tpic2810 0 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out1 { + label = "out1"; + gpios = <&tpic2810 1 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out2 { + label = "out2"; + gpios = <&tpic2810 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out3 { + label = "out3"; + gpios = <&tpic2810 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out4 { + label = "out4"; + gpios = <&tpic2810 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out5 { + label = "out5"; + gpios = <&tpic2810 5 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out6 { + label = "out6"; + gpios = <&tpic2810 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out7 { + label = "out7"; + gpios = <&tpic2810 7 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; }; &am43xx_pinmux { @@ -178,6 +230,24 @@ >; }; + spi1_pins_default: spi1_pins_default { + pinctrl-single,pins = < + AM4372_IOPAD(0x908, PIN_INPUT | MUX_MODE2) /* mii1_col.spi1_sclk */ + AM4372_IOPAD(0x910, PIN_INPUT | MUX_MODE2) /* mii1_rx_er.spi1_d1 */ + AM4372_IOPAD(0x944, PIN_OUTPUT | MUX_MODE2) /* rmii1_ref_clk.spi1_cs0 */ + AM4372_IOPAD(0x90c, PIN_OUTPUT | MUX_MODE7) /* mii1_crs.gpio3_1 */ + >; + }; + + spi1_pins_sleep: spi1_pins_sleep { + pinctrl-single,pins = < + AM4372_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) + AM4372_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + ecap0_pins_default: backlight_pins_default { pinctrl-single,pins = < AM4372_IOPAD(0x964, PIN_OUTPUT | MUX_MODE0) /* ecap0_in_pwm0_out.ecap0_in_pwm0_out */ @@ -290,6 +360,33 @@ pinctrl-0 = <&i2c2_pins_default>; pinctrl-1 = <&i2c2_pins_sleep>; clock-frequency = <100000>; + + tpic2810: tpic2810@60 { + compatible = "ti,tpic2810"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&spi1_pins_default>; + pinctrl-1 = <&spi1_pins_sleep>; + ti,pindir-d0-out-d1-in; + + sn65hvs882: sn65hvs882@0 { + compatible = "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + load-gpios = <&gpio3 1 GPIO_ACTIVE_LOW>; + + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + }; }; &epwmss0 { @@ -310,6 +407,10 @@ status = "okay"; }; +&gpio3 { + status = "okay"; +}; + &gpio4 { status = "okay"; }; diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts new file mode 100644 index 000000000000..d6e43e5184c1 --- /dev/null +++ b/arch/arm/boot/dts/am571x-idk.dts @@ -0,0 +1,81 @@ +/* + * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "dra72x.dtsi" +#include +#include +#include "am57xx-idk-common.dtsi" + +/ { + model = "TI AM5718 IDK"; + compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7"; + + memory@80000000 { + device_type = "memory"; + reg = <0x0 0x80000000 0x0 0x40000000>; + }; + + leds { + compatible = "gpio-leds"; + cpu0-led { + label = "status0:red:cpu0"; + gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "cpu0"; + }; + + usr0-led { + label = "status0:green:usr"; + gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + heartbeat-led { + label = "status0:blue:heartbeat"; + gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + usr1-led { + label = "status1:red:usr"; + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + usr2-led { + label = "status1:green:usr"; + gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + mmc0-led { + label = "status1:blue:mmc0"; + gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "mmc0"; + }; + }; + + extcon_usb2: extcon_usb2 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>; + }; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&ldo1_reg>; + bus-width = <4>; + cd-gpios = <&gpio6 27 0>; /* gpio 219 */ +}; + +&omap_dwc3_2 { + extcon = <&extcon_usb2>; +}; diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts index 87bbc66f0f21..27d9149cedba 100644 --- a/arch/arm/boot/dts/am572x-idk.dts +++ b/arch/arm/boot/dts/am572x-idk.dts @@ -83,3 +83,7 @@ bus-width = <4>; cd-gpios = <&gpio6 27 0>; /* gpio 219 */ }; + +&sn65hvs882 { + load-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; +}; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index 6df7829a2c15..78bee26361f1 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -204,6 +204,7 @@ interrupt-controller; ti,system-power-controller; + ti,palmas-override-powerhold; tps659038_pmic { compatible = "ti,tps659038-pmic"; diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi index 03cec62260e1..555ae21f2b9a 100644 --- a/arch/arm/boot/dts/am57xx-idk-common.dtsi +++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi @@ -43,6 +43,58 @@ regulator-always-on; regulator-boot-on; }; + + leds-iio { + status = "disabled"; + compatible = "gpio-leds"; + led-out0 { + label = "out0"; + gpios = <&tpic2810 0 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out1 { + label = "out1"; + gpios = <&tpic2810 1 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out2 { + label = "out2"; + gpios = <&tpic2810 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out3 { + label = "out3"; + gpios = <&tpic2810 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out4 { + label = "out4"; + gpios = <&tpic2810 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out5 { + label = "out5"; + gpios = <&tpic2810 5 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out6 { + label = "out6"; + gpios = <&tpic2810 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out7 { + label = "out7"; + gpios = <&tpic2810 7 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; }; &i2c1 { @@ -57,6 +109,7 @@ #interrupt-cells = <2>; interrupt-controller; ti,system-power-controller; + ti,palmas-override-powerhold; tps659038_pmic { compatible = "ti,tps659038-pmic"; @@ -253,6 +306,28 @@ }; }; +&mcspi3 { + status = "okay"; + ti,pindir-d0-out-d1-in; + + sn65hvs882: sn65hvs882@0 { + compatible = "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + }; + + tpic2810: tpic2810@60 { + compatible = "ti,tpic2810"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + &uart3 { status = "okay"; interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 2fcdc516da45..a8c72611fbe3 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -41,7 +41,7 @@ label = "BTN1"; linux,code = <169>; gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 */ - gpio-key,wakeup; + wakeup-source; autorepeat; debounce_interval = <50>; };