mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-06 02:24:14 +08:00
media: i2c: ov5640: Configure HVP lines in s_power callback
Configure HVP lines in s_power callback instead of configuring everytime in ov5640_set_stream_dvp(). Alongside also disable MIPI in DVP mode. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Tested-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This commit is contained in:
parent
576f5d4ba8
commit
311a6408f8
@ -1217,71 +1217,6 @@ static int ov5640_set_autogain(struct ov5640_dev *sensor, bool on)
|
||||
|
||||
static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on)
|
||||
{
|
||||
int ret;
|
||||
unsigned int flags = sensor->ep.bus.parallel.flags;
|
||||
u8 pclk_pol = 0;
|
||||
u8 hsync_pol = 0;
|
||||
u8 vsync_pol = 0;
|
||||
|
||||
/*
|
||||
* Note about parallel port configuration.
|
||||
*
|
||||
* When configured in parallel mode, the OV5640 will
|
||||
* output 10 bits data on DVP data lines [9:0].
|
||||
* If only 8 bits data are wanted, the 8 bits data lines
|
||||
* of the camera interface must be physically connected
|
||||
* on the DVP data lines [9:2].
|
||||
*
|
||||
* Control lines polarity can be configured through
|
||||
* devicetree endpoint control lines properties.
|
||||
* If no endpoint control lines properties are set,
|
||||
* polarity will be as below:
|
||||
* - VSYNC: active high
|
||||
* - HREF: active low
|
||||
* - PCLK: active low
|
||||
*/
|
||||
|
||||
if (on) {
|
||||
/*
|
||||
* configure parallel port control lines polarity
|
||||
*
|
||||
* POLARITY CTRL0
|
||||
* - [5]: PCLK polarity (0: active low, 1: active high)
|
||||
* - [1]: HREF polarity (0: active low, 1: active high)
|
||||
* - [0]: VSYNC polarity (mismatch here between
|
||||
* datasheet and hardware, 0 is active high
|
||||
* and 1 is active low...)
|
||||
*/
|
||||
if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
|
||||
pclk_pol = 1;
|
||||
if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
|
||||
hsync_pol = 1;
|
||||
if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
|
||||
vsync_pol = 1;
|
||||
|
||||
ret = ov5640_write_reg(sensor,
|
||||
OV5640_REG_POLARITY_CTRL00,
|
||||
(pclk_pol << 5) |
|
||||
(hsync_pol << 1) |
|
||||
vsync_pol);
|
||||
|
||||
if (ret)
|
||||
return ret;
|
||||
}
|
||||
|
||||
/*
|
||||
* powerdown MIPI TX/RX PHY & disable MIPI
|
||||
*
|
||||
* MIPI CONTROL 00
|
||||
* 4: PWDN PHY TX
|
||||
* 3: PWDN PHY RX
|
||||
* 2: MIPI enable
|
||||
*/
|
||||
ret = ov5640_write_reg(sensor,
|
||||
OV5640_REG_IO_MIPI_CTRL00, on ? 0x18 : 0);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
return ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, on ?
|
||||
OV5640_REG_SYS_CTRL0_SW_PWUP :
|
||||
OV5640_REG_SYS_CTRL0_SW_PWDN);
|
||||
@ -2043,15 +1978,73 @@ static int ov5640_set_power_mipi(struct ov5640_dev *sensor, bool on)
|
||||
|
||||
static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on)
|
||||
{
|
||||
unsigned int flags = sensor->ep.bus.parallel.flags;
|
||||
u8 pclk_pol = 0;
|
||||
u8 hsync_pol = 0;
|
||||
u8 vsync_pol = 0;
|
||||
int ret;
|
||||
|
||||
if (!on) {
|
||||
/* Reset settings to their default values. */
|
||||
ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x58);
|
||||
ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00, 0x20);
|
||||
ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE01, 0x00);
|
||||
ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE02, 0x00);
|
||||
return 0;
|
||||
}
|
||||
|
||||
/*
|
||||
* Note about parallel port configuration.
|
||||
*
|
||||
* When configured in parallel mode, the OV5640 will
|
||||
* output 10 bits data on DVP data lines [9:0].
|
||||
* If only 8 bits data are wanted, the 8 bits data lines
|
||||
* of the camera interface must be physically connected
|
||||
* on the DVP data lines [9:2].
|
||||
*
|
||||
* Control lines polarity can be configured through
|
||||
* devicetree endpoint control lines properties.
|
||||
* If no endpoint control lines properties are set,
|
||||
* polarity will be as below:
|
||||
* - VSYNC: active high
|
||||
* - HREF: active low
|
||||
* - PCLK: active low
|
||||
*/
|
||||
/*
|
||||
* configure parallel port control lines polarity
|
||||
*
|
||||
* POLARITY CTRL0
|
||||
* - [5]: PCLK polarity (0: active low, 1: active high)
|
||||
* - [1]: HREF polarity (0: active low, 1: active high)
|
||||
* - [0]: VSYNC polarity (mismatch here between
|
||||
* datasheet and hardware, 0 is active high
|
||||
* and 1 is active low...)
|
||||
*/
|
||||
if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
|
||||
pclk_pol = 1;
|
||||
if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
|
||||
hsync_pol = 1;
|
||||
if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
|
||||
vsync_pol = 1;
|
||||
|
||||
ret = ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00,
|
||||
(pclk_pol << 5) | (hsync_pol << 1) | vsync_pol);
|
||||
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
/*
|
||||
* powerdown MIPI TX/RX PHY & disable MIPI
|
||||
*
|
||||
* MIPI CONTROL 00
|
||||
* 4: PWDN PHY TX
|
||||
* 3: PWDN PHY RX
|
||||
* 2: MIPI enable
|
||||
*/
|
||||
ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x18);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
/*
|
||||
* enable VSYNC/HREF/PCLK DVP control lines
|
||||
* & D[9:6] DVP data lines
|
||||
|
Loading…
Reference in New Issue
Block a user