mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-11 12:28:41 +08:00
x86: multi pci root bus with different io resource range, on 64-bit
scan AMD opteron io/mmio routing to make sure every pci root bus get correct resource range. Thus later pci scan could assign correct resource to device with unassigned resource. this can fix a system without _CRS for multi pci root bus. Signed-off-by: Yinghai Lu <yinghai.lu@sun.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This commit is contained in:
Yinghai Lu
Ingo Molnar
parent
35ddd068fb
commit
30a18d6c3f
@ -13,5 +13,5 @@ obj-y += legacy.o irq.o common.o early.o
|
||||
# mmconfig has a 64bit special
|
||||
obj-$(CONFIG_PCI_MMCONFIG) += mmconfig_64.o direct.o mmconfig-shared.o
|
||||
|
||||
obj-$(CONFIG_NUMA) += k8-bus_64.o
|
||||
obj-y += k8-bus_64.o
|
||||
|
||||
|
||||
@ -7,23 +7,29 @@
|
||||
|
||||
/*
|
||||
* This discovers the pcibus <-> node mapping on AMD K8.
|
||||
*
|
||||
* RED-PEN need to call this again on PCI hotplug
|
||||
* RED-PEN empty cpus get reported wrong
|
||||
* also get peer root bus resource for io,mmio
|
||||
*/
|
||||
|
||||
#define NODE_ID(dword) ((dword>>4) & 0x07)
|
||||
#define LDT_BUS_NUMBER_REGISTER_0 0xE0
|
||||
#define LDT_BUS_NUMBER_REGISTER_1 0xE4
|
||||
#define LDT_BUS_NUMBER_REGISTER_2 0xE8
|
||||
#define LDT_BUS_NUMBER_REGISTER_3 0xEC
|
||||
#define NR_LDT_BUS_NUMBER_REGISTERS 4
|
||||
#define SECONDARY_LDT_BUS_NUMBER(dword) ((dword >> 16) & 0xFF)
|
||||
#define SUBORDINATE_LDT_BUS_NUMBER(dword) ((dword >> 24) & 0xFF)
|
||||
|
||||
#define PCI_DEVICE_ID_K8HTCONFIG 0x1100
|
||||
#define PCI_DEVICE_ID_K8_10H_HTCONFIG 0x1200
|
||||
#define PCI_DEVICE_ID_K8_11H_HTCONFIG 0x1300
|
||||
/*
|
||||
* sub bus (transparent) will use entres from 3 to store extra from root,
|
||||
* so need to make sure have enought slot there, increase PCI_BUS_NUM_RESOURCES?
|
||||
*/
|
||||
#define RES_NUM 16
|
||||
struct pci_root_info {
|
||||
char name[12];
|
||||
unsigned int res_num;
|
||||
struct resource res[RES_NUM];
|
||||
int bus_min;
|
||||
int bus_max;
|
||||
int node;
|
||||
int link;
|
||||
};
|
||||
|
||||
/* 4 at this time, it may become to 32 */
|
||||
#define PCI_ROOT_NR 4
|
||||
static int pci_root_num;
|
||||
static struct pci_root_info pci_root_info[PCI_ROOT_NR];
|
||||
|
||||
#ifdef CONFIG_NUMA
|
||||
|
||||
@ -55,77 +61,375 @@ int get_mp_bus_to_node(int busnum)
|
||||
|
||||
return node;
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
void set_pci_bus_resources_arch_default(struct pci_bus *b)
|
||||
{
|
||||
int i;
|
||||
int j;
|
||||
struct pci_root_info *info;
|
||||
|
||||
if (!pci_root_num)
|
||||
return;
|
||||
|
||||
for (i = 0; i < pci_root_num; i++) {
|
||||
if (pci_root_info[i].bus_min == b->number)
|
||||
break;
|
||||
}
|
||||
|
||||
if (i == pci_root_num)
|
||||
return;
|
||||
|
||||
info = &pci_root_info[i];
|
||||
for (j = 0; j < info->res_num; j++) {
|
||||
struct resource *res;
|
||||
struct resource *root;
|
||||
|
||||
res = &info->res[j];
|
||||
b->resource[j] = res;
|
||||
if (res->flags & IORESOURCE_IO)
|
||||
root = &ioport_resource;
|
||||
else
|
||||
root = &iomem_resource;
|
||||
insert_resource(root, res);
|
||||
}
|
||||
}
|
||||
|
||||
#define RANGE_NUM 16
|
||||
|
||||
struct res_range {
|
||||
size_t start;
|
||||
size_t end;
|
||||
};
|
||||
|
||||
static void __init update_range(struct res_range *range, size_t start,
|
||||
size_t end)
|
||||
{
|
||||
int i;
|
||||
int j;
|
||||
|
||||
for (j = 0; j < RANGE_NUM; j++) {
|
||||
if (!range[j].end)
|
||||
continue;
|
||||
if (start == range[j].start && end < range[j].end) {
|
||||
range[j].start = end + 1;
|
||||
break;
|
||||
} else if (start == range[j].start && end == range[j].end) {
|
||||
range[j].start = 0;
|
||||
range[j].end = 0;
|
||||
break;
|
||||
} else if (start > range[j].start && end == range[j].end) {
|
||||
range[j].end = start - 1;
|
||||
break;
|
||||
} else if (start > range[j].start && end < range[j].end) {
|
||||
/* find the new spare */
|
||||
for (i = 0; i < RANGE_NUM; i++) {
|
||||
if (range[i].end == 0)
|
||||
break;
|
||||
}
|
||||
if (i < RANGE_NUM) {
|
||||
range[i].end = range[j].end;
|
||||
range[i].start = end + 1;
|
||||
} else {
|
||||
printk(KERN_ERR "run of slot in ranges\n");
|
||||
}
|
||||
range[j].end = start - 1;
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
static void __init update_res(struct pci_root_info *info, size_t start,
|
||||
size_t end, unsigned long flags, int merge)
|
||||
{
|
||||
int i;
|
||||
struct resource *res;
|
||||
|
||||
if (!merge)
|
||||
goto addit;
|
||||
|
||||
/* try to merge it with old one */
|
||||
for (i = 0; i < info->res_num; i++) {
|
||||
res = &info->res[i];
|
||||
if (res->flags != flags)
|
||||
continue;
|
||||
if (res->end + 1 == start) {
|
||||
res->end = end;
|
||||
return;
|
||||
} else if (end + 1 == res->start) {
|
||||
res->start = start;
|
||||
return;
|
||||
}
|
||||
}
|
||||
|
||||
addit:
|
||||
|
||||
/* need to add that */
|
||||
if (info->res_num >= RES_NUM)
|
||||
return;
|
||||
|
||||
res = &info->res[info->res_num];
|
||||
res->name = info->name;
|
||||
res->flags = flags;
|
||||
res->start = start;
|
||||
res->end = end;
|
||||
res->child = NULL;
|
||||
info->res_num++;
|
||||
}
|
||||
|
||||
struct pci_hostbridge_probe {
|
||||
u32 bus;
|
||||
u32 slot;
|
||||
u32 vendor;
|
||||
u32 device;
|
||||
};
|
||||
|
||||
static struct pci_hostbridge_probe pci_probes[] __initdata = {
|
||||
{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1100 },
|
||||
{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
|
||||
{ 0xff, 0, PCI_VENDOR_ID_AMD, 0x1200 },
|
||||
{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1300 },
|
||||
};
|
||||
|
||||
/**
|
||||
* early_fill_mp_bus_to_node()
|
||||
* called before pcibios_scan_root and pci_scan_bus
|
||||
* fills the mp_bus_to_cpumask array based according to the LDT Bus Number
|
||||
* Registers found in the K8 northbridge
|
||||
*/
|
||||
__init static int
|
||||
early_fill_mp_bus_to_node(void)
|
||||
static int __init early_fill_mp_bus_info(void)
|
||||
{
|
||||
#ifdef CONFIG_NUMA
|
||||
int i, j;
|
||||
int i;
|
||||
int j;
|
||||
unsigned bus;
|
||||
unsigned slot;
|
||||
u32 ldtbus;
|
||||
u32 id;
|
||||
int found;
|
||||
int node;
|
||||
u16 deviceid;
|
||||
u16 vendorid;
|
||||
int min_bus;
|
||||
int max_bus;
|
||||
|
||||
static int lbnr[NR_LDT_BUS_NUMBER_REGISTERS] = {
|
||||
LDT_BUS_NUMBER_REGISTER_0,
|
||||
LDT_BUS_NUMBER_REGISTER_1,
|
||||
LDT_BUS_NUMBER_REGISTER_2,
|
||||
LDT_BUS_NUMBER_REGISTER_3
|
||||
};
|
||||
int link;
|
||||
int def_node;
|
||||
int def_link;
|
||||
struct pci_root_info *info;
|
||||
u32 reg;
|
||||
struct resource *res;
|
||||
size_t start;
|
||||
size_t end;
|
||||
struct res_range range[RANGE_NUM];
|
||||
u64 val;
|
||||
u32 address;
|
||||
|
||||
#ifdef CONFIG_NUMA
|
||||
for (i = 0; i < BUS_NR; i++)
|
||||
mp_bus_to_node[i] = -1;
|
||||
#endif
|
||||
|
||||
if (!early_pci_allowed())
|
||||
return -1;
|
||||
|
||||
slot = 0x18;
|
||||
id = read_pci_config(0, slot, 0, PCI_VENDOR_ID);
|
||||
found = 0;
|
||||
for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
|
||||
u32 id;
|
||||
u16 device;
|
||||
u16 vendor;
|
||||
|
||||
vendorid = id & 0xffff;
|
||||
if (vendorid != PCI_VENDOR_ID_AMD)
|
||||
goto out;
|
||||
bus = pci_probes[i].bus;
|
||||
slot = pci_probes[i].slot;
|
||||
id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
|
||||
|
||||
deviceid = (id>>16) & 0xffff;
|
||||
if ((deviceid != PCI_DEVICE_ID_K8HTCONFIG) &&
|
||||
(deviceid != PCI_DEVICE_ID_K8_10H_HTCONFIG) &&
|
||||
(deviceid != PCI_DEVICE_ID_K8_11H_HTCONFIG))
|
||||
goto out;
|
||||
|
||||
for (i = 0; i < NR_LDT_BUS_NUMBER_REGISTERS; i++) {
|
||||
ldtbus = read_pci_config(0, slot, 1, lbnr[i]);
|
||||
|
||||
/* Check if that register is enabled for bus range */
|
||||
if ((ldtbus & 7) != 3)
|
||||
continue;
|
||||
|
||||
min_bus = SECONDARY_LDT_BUS_NUMBER(ldtbus);
|
||||
max_bus = SUBORDINATE_LDT_BUS_NUMBER(ldtbus);
|
||||
node = NODE_ID(ldtbus);
|
||||
for (j = min_bus; j <= max_bus; j++)
|
||||
mp_bus_to_node[j] = (unsigned char) node;
|
||||
vendor = id & 0xffff;
|
||||
device = (id>>16) & 0xffff;
|
||||
if (pci_probes[i].vendor == vendor &&
|
||||
pci_probes[i].device == device) {
|
||||
found = 1;
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
out:
|
||||
if (!found)
|
||||
return 0;
|
||||
|
||||
pci_root_num = 0;
|
||||
for (i = 0; i < 4; i++) {
|
||||
int min_bus;
|
||||
int max_bus;
|
||||
reg = read_pci_config(bus, slot, 1, 0xe0 + (i << 2));
|
||||
|
||||
/* Check if that register is enabled for bus range */
|
||||
if ((reg & 7) != 3)
|
||||
continue;
|
||||
|
||||
min_bus = (reg >> 16) & 0xff;
|
||||
max_bus = (reg >> 24) & 0xff;
|
||||
node = (reg >> 4) & 0x07;
|
||||
#ifdef CONFIG_NUMA
|
||||
for (j = min_bus; j <= max_bus; j++)
|
||||
mp_bus_to_node[j] = (unsigned char) node;
|
||||
#endif
|
||||
link = (reg >> 8) & 0x03;
|
||||
|
||||
info = &pci_root_info[pci_root_num];
|
||||
info->bus_min = min_bus;
|
||||
info->bus_max = max_bus;
|
||||
info->node = node;
|
||||
info->link = link;
|
||||
sprintf(info->name, "PCI Bus #%02x", min_bus);
|
||||
pci_root_num++;
|
||||
}
|
||||
|
||||
/* get the default node and link for left over res */
|
||||
reg = read_pci_config(bus, slot, 0, 0x60);
|
||||
def_node = (reg >> 8) & 0x07;
|
||||
reg = read_pci_config(bus, slot, 0, 0x64);
|
||||
def_link = (reg >> 8) & 0x03;
|
||||
|
||||
memset(range, 0, sizeof(range));
|
||||
range[0].end = 0xffff;
|
||||
/* io port resource */
|
||||
for (i = 0; i < 4; i++) {
|
||||
reg = read_pci_config(bus, slot, 1, 0xc0 + (i << 3));
|
||||
if (!(reg & 3))
|
||||
continue;
|
||||
|
||||
start = reg & 0xfff000;
|
||||
reg = read_pci_config(bus, slot, 1, 0xc4 + (i << 3));
|
||||
node = reg & 0x07;
|
||||
link = (reg >> 4) & 0x03;
|
||||
end = (reg & 0xfff000) | 0xfff;
|
||||
|
||||
/* find the position */
|
||||
for (j = 0; j < pci_root_num; j++) {
|
||||
info = &pci_root_info[j];
|
||||
if (info->node == node && info->link == link)
|
||||
break;
|
||||
}
|
||||
if (j == pci_root_num)
|
||||
continue; /* not found */
|
||||
|
||||
info = &pci_root_info[j];
|
||||
update_res(info, start, end, IORESOURCE_IO, 0);
|
||||
update_range(range, start, end);
|
||||
}
|
||||
/* add left over io port range to def node/link, [0, 0xffff] */
|
||||
/* find the position */
|
||||
for (j = 0; j < pci_root_num; j++) {
|
||||
info = &pci_root_info[j];
|
||||
if (info->node == def_node && info->link == def_link)
|
||||
break;
|
||||
}
|
||||
if (j < pci_root_num) {
|
||||
info = &pci_root_info[j];
|
||||
for (i = 0; i < RANGE_NUM; i++) {
|
||||
if (!range[i].end)
|
||||
continue;
|
||||
|
||||
update_res(info, range[i].start, range[i].end,
|
||||
IORESOURCE_IO, 1);
|
||||
}
|
||||
}
|
||||
|
||||
memset(range, 0, sizeof(range));
|
||||
/* 0xfd00000000-0xffffffffff for HT */
|
||||
/* 0xfc00000000-0xfcffffffff for Family 10h mmconfig*/
|
||||
range[0].end = 0xfbffffffffULL;
|
||||
|
||||
/* need to take out [0, TOM) for RAM*/
|
||||
address = MSR_K8_TOP_MEM1;
|
||||
rdmsrl(address, val);
|
||||
end = (val & 0xffffff8000000ULL);
|
||||
printk(KERN_INFO "TOM: %016lx aka %ldM\n", end, end>>20);
|
||||
if (end < (1ULL<<32))
|
||||
update_range(range, 0, end - 1);
|
||||
|
||||
/* mmio resource */
|
||||
for (i = 0; i < 8; i++) {
|
||||
reg = read_pci_config(bus, slot, 1, 0x80 + (i << 3));
|
||||
if (!(reg & 3))
|
||||
continue;
|
||||
|
||||
start = reg & 0xffffff00; /* 39:16 on 31:8*/
|
||||
start <<= 8;
|
||||
reg = read_pci_config(bus, slot, 1, 0x84 + (i << 3));
|
||||
node = reg & 0x07;
|
||||
link = (reg >> 4) & 0x03;
|
||||
end = (reg & 0xffffff00);
|
||||
end <<= 8;
|
||||
end |= 0xffff;
|
||||
|
||||
/* find the position */
|
||||
for (j = 0; j < pci_root_num; j++) {
|
||||
info = &pci_root_info[j];
|
||||
if (info->node == node && info->link == link)
|
||||
break;
|
||||
}
|
||||
if (j == pci_root_num)
|
||||
continue; /* not found */
|
||||
|
||||
info = &pci_root_info[j];
|
||||
update_res(info, start, end, IORESOURCE_MEM, 0);
|
||||
update_range(range, start, end);
|
||||
}
|
||||
|
||||
/* need to take out [4G, TOM2) for RAM*/
|
||||
/* SYS_CFG */
|
||||
address = MSR_K8_SYSCFG;
|
||||
rdmsrl(address, val);
|
||||
/* TOP_MEM2 is enabled? */
|
||||
if (val & (1<<21)) {
|
||||
/* TOP_MEM2 */
|
||||
address = MSR_K8_TOP_MEM2;
|
||||
rdmsrl(address, val);
|
||||
end = (val & 0xffffff8000000ULL);
|
||||
printk(KERN_INFO "TOM2: %016lx aka %ldM\n", end, end>>20);
|
||||
update_range(range, 1ULL<<32, end - 1);
|
||||
}
|
||||
|
||||
/*
|
||||
* add left over mmio range to def node/link ?
|
||||
* that is tricky, just record range in from start_min to 4G
|
||||
*/
|
||||
for (j = 0; j < pci_root_num; j++) {
|
||||
info = &pci_root_info[j];
|
||||
if (info->node == def_node && info->link == def_link)
|
||||
break;
|
||||
}
|
||||
if (j < pci_root_num) {
|
||||
info = &pci_root_info[j];
|
||||
|
||||
for (i = 0; i < RANGE_NUM; i++) {
|
||||
if (!range[i].end)
|
||||
continue;
|
||||
|
||||
update_res(info, range[i].start, range[i].end,
|
||||
IORESOURCE_MEM, 1);
|
||||
}
|
||||
}
|
||||
|
||||
#ifdef CONFIG_NUMA
|
||||
for (i = 0; i < BUS_NR; i++) {
|
||||
node = mp_bus_to_node[i];
|
||||
if (node >= 0)
|
||||
printk(KERN_DEBUG "bus: %02x to node: %02x\n", i, node);
|
||||
}
|
||||
#endif
|
||||
|
||||
for (i = 0; i < pci_root_num; i++) {
|
||||
int res_num;
|
||||
int busnum;
|
||||
|
||||
info = &pci_root_info[i];
|
||||
res_num = info->res_num;
|
||||
busnum = info->bus_min;
|
||||
printk(KERN_DEBUG "bus: [%02x,%02x] on node %x link %x\n",
|
||||
info->bus_min, info->bus_max, info->node, info->link);
|
||||
for (j = 0; j < res_num; j++) {
|
||||
res = &info->res[j];
|
||||
printk(KERN_DEBUG "bus: %02x index %x %s: [%llx, %llx]\n",
|
||||
busnum, j,
|
||||
(res->flags & IORESOURCE_IO)?"io port":"mmio",
|
||||
res->start, res->end);
|
||||
}
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
postcore_initcall(early_fill_mp_bus_to_node);
|
||||
postcore_initcall(early_fill_mp_bus_info);
|
||||
|
||||
@ -1088,6 +1088,10 @@ unsigned int __devinit pci_scan_child_bus(struct pci_bus *bus)
|
||||
return max;
|
||||
}
|
||||
|
||||
void __attribute__((weak)) set_pci_bus_resources_arch_default(struct pci_bus *b)
|
||||
{
|
||||
}
|
||||
|
||||
struct pci_bus * pci_create_bus(struct device *parent,
|
||||
int bus, struct pci_ops *ops, void *sysdata)
|
||||
{
|
||||
@ -1147,6 +1151,8 @@ struct pci_bus * pci_create_bus(struct device *parent,
|
||||
b->resource[0] = &ioport_resource;
|
||||
b->resource[1] = &iomem_resource;
|
||||
|
||||
set_pci_bus_resources_arch_default(b);
|
||||
|
||||
return b;
|
||||
|
||||
dev_create_file_err:
|
||||
|
||||
@ -193,6 +193,9 @@ extern cpumask_t cpu_coregroup_map(int cpu);
|
||||
#define topology_thread_siblings(cpu) (per_cpu(cpu_sibling_map, cpu))
|
||||
#endif
|
||||
|
||||
struct pci_bus;
|
||||
void set_pci_bus_resources_arch_default(struct pci_bus *b);
|
||||
|
||||
#ifdef CONFIG_SMP
|
||||
#define mc_capable() (boot_cpu_data.x86_max_cores > 1)
|
||||
#define smt_capable() (smp_num_siblings > 1)
|
||||
|
||||
@ -254,7 +254,7 @@ static inline void pci_add_saved_cap(struct pci_dev *pci_dev,
|
||||
#define PCI_NUM_RESOURCES 11
|
||||
|
||||
#ifndef PCI_BUS_NUM_RESOURCES
|
||||
#define PCI_BUS_NUM_RESOURCES 8
|
||||
#define PCI_BUS_NUM_RESOURCES 16
|
||||
#endif
|
||||
|
||||
#define PCI_REGION_FLAG_MASK 0x0fU /* These bits of resource flags tell us the PCI region flags */
|
||||
|
||||
Loading…
Reference in New Issue
Block a user