diff --git a/Documentation/media/v4l-drivers/bttv.rst b/Documentation/media/v4l-drivers/bttv.rst new file mode 100644 index 000000000000..d7d956835e38 --- /dev/null +++ b/Documentation/media/v4l-drivers/bttv.rst @@ -0,0 +1,1881 @@ +The bttv driver +=============== + + +Release notes for bttv +---------------------- + +You'll need at least these config options for bttv: + CONFIG_I2C=m + CONFIG_I2C_ALGOBIT=m + CONFIG_VIDEO_DEV=m + +The latest bttv version is available from http://bytesex.org/bttv/ + + +Make bttv work with your card +----------------------------- + +Just try "modprobe bttv" and see if that works. + +If it doesn't bttv likely could not autodetect your card and needs some +insmod options. The most important insmod option for bttv is "card=n" +to select the correct card type. If you get video but no sound you've +very likely specified the wrong (or no) card type. A list of supported +cards is in CARDLIST.bttv + +If bttv takes very long to load (happens sometimes with the cheap +cards which have no tuner), try adding this to your modules.conf: + options i2c-algo-bit bit_test=1 + +For the WinTV/PVR you need one firmware file from the driver CD: +hcwamc.rbf. The file is in the pvr45xxx.exe archive (self-extracting +zip file, unzip can unpack it). Put it into the /etc/pvr directory or +use the firm_altera= insmod option to point the driver to the +location of the file. + +If your card isn't listed in CARDLIST.bttv or if you have trouble making +audio work, you should read the Sound-FAQ. + + +Autodetecting cards +------------------- + +bttv uses the PCI Subsystem ID to autodetect the card type. lspci lists +the Subsystem ID in the second line, looks like this: + +00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02) + Subsystem: Hauppauge computer works Inc. WinTV/GO + Flags: bus master, medium devsel, latency 32, IRQ 5 + Memory at e2000000 (32-bit, prefetchable) [size=4K] + +only bt878-based cards can have a subsystem ID (which does not mean +that every card really has one). bt848 cards can't have a Subsystem +ID and therefore can't be autodetected. There is a list with the ID's +in bttv-cards.c (in case you are intrested or want to mail patches +with updates). + + +Still doesn't work? +------------------- + +I do NOT have a lab with 30+ different grabber boards and a +PAL/NTSC/SECAM test signal generator at home, so I often can't +reproduce your problems. This makes debugging very difficult for me. +If you have some knowledge and spare time, please try to fix this +yourself (patches very welcome of course...) You know: The linux +slogan is "Do it yourself". + +There is a mailing list: linux-media@vger.kernel.org +http://vger.kernel.org/vger-lists.html#linux-media + +If you have trouble with some specific TV card, try to ask there +instead of mailing me directly. The chance that someone with the +same card listens there is much higher... + +For problems with sound: There are a lot of different systems used +for TV sound all over the world. And there are also different chips +which decode the audio signal. Reports about sound problems ("stereo +does'nt work") are pretty useless unless you include some details +about your hardware and the TV sound scheme used in your country (or +at least the country you are living in). + +Modprobe options +---------------- + +Note: "modinfo " prints various information about a kernel +module, among them a complete and up-to-date list of insmod options. +This list tends to be outdated because it is updated manually ... + +========================================================================== + +bttv.o + +:: + + the bt848/878 (grabber chip) driver + + insmod args: + card=n card type, see CARDLIST for a list. + tuner=n tuner type, see CARDLIST for a list. + radio=0/1 card supports radio + pll=0/1/2 pll settings + 0: don't use PLL + 1: 28 MHz crystal installed + 2: 35 MHz crystal installed + + triton1=0/1 for Triton1 (+others) compatibility + vsfx=0/1 yet another chipset bug compatibility bit + see README.quirks for details on these two. + + bigendian=n Set the endianness of the gfx framebuffer. + Default is native endian. + fieldnr=0/1 Count fields. Some TV descrambling software + needs this, for others it only generates + 50 useless IRQs/sec. default is 0 (off). + autoload=0/1 autoload helper modules (tuner, audio). + default is 1 (on). + bttv_verbose=0/1/2 verbose level (at insmod time, while + looking at the hardware). default is 1. + bttv_debug=0/1 debug messages (for capture). + default is 0 (off). + irq_debug=0/1 irq handler debug messages. + default is 0 (off). + gbuffers=2-32 number of capture buffers for mmap'ed capture. + default is 4. + gbufsize= size of capture buffers. default and + maximum value is 0x208000 (~2MB) + no_overlay=0 Enable overlay on broken hardware. There + are some chipsets (SIS for example) which + are known to have problems with the PCI DMA + push used by bttv. bttv will disable overlay + by default on this hardware to avoid crashes. + With this insmod option you can override this. + no_overlay=1 Disable overlay. It should be used by broken + hardware that doesn't support PCI2PCI direct + transfers. + automute=0/1 Automatically mutes the sound if there is + no TV signal, on by default. You might try + to disable this if you have bad input signal + quality which leading to unwanted sound + dropouts. + chroma_agc=0/1 AGC of chroma signal, off by default. + adc_crush=0/1 Luminance ADC crush, on by default. + i2c_udelay= Allow reduce I2C speed. Default is 5 usecs + (meaning 66,67 Kbps). The default is the + maximum supported speed by kernel bitbang + algorithm. You may use lower numbers, if I2C + messages are lost (16 is known to work on + all supported cards). + + bttv_gpio=0/1 + gpiomask= + audioall= + audiomux= + See Sound-FAQ for a detailed description. + + remap, card, radio and pll accept up to four comma-separated arguments + (for multiple boards). + +tuner.o + +:: + + The tuner driver. You need this unless you want to use only + with a camera or external tuner ... + + insmod args: + debug=1 print some debug info to the syslog + type=n type of the tuner chip. n as follows: + see CARDLIST for a complete list. + pal=[bdgil] select PAL variant (used for some tuners + only, important for the audio carrier). + +tvaudio.o + +:: + + new, experimental module which is supported to provide a single + driver for all simple i2c audio control chips (tda/tea*). + + insmod args: + tda8425 = 1 enable/disable the support for the + tda9840 = 1 various chips. + tda9850 = 1 The tea6300 can't be autodetected and is + tda9855 = 1 therefore off by default, if you have + tda9873 = 1 this one on your card (STB uses these) + tda9874a = 1 you have to enable it explicitly. + tea6300 = 0 The two tda985x chips use the same i2c + tea6420 = 1 address and can't be disturgished from + pic16c54 = 1 each other, you might have to disable + the wrong one. + debug = 1 print debug messages + + insmod args for tda9874a: + tda9874a_SIF=1/2 select sound IF input pin (1 or 2) + (default is pin 1) + tda9874a_AMSEL=0/1 auto-mute select for NICAM (default=0) + Please read note 3 below! + tda9874a_STD=n select TV sound standard (0..8): + 0 - A2, B/G + 1 - A2, M (Korea) + 2 - A2, D/K (1) + 3 - A2, D/K (2) + 4 - A2, D/K (3) + 5 - NICAM, I + 6 - NICAM, B/G + 7 - NICAM, D/K (default) + 8 - NICAM, L + + Note 1: tda9874a supports both tda9874h (old) and tda9874a (new) chips. + Note 2: tda9874h/a and tda9875 (which is supported separately by + tda9875.o) use the same i2c address so both modules should not be + used at the same time. + Note 3: Using tda9874a_AMSEL option depends on your TV card design! + AMSEL=0: auto-mute will switch between NICAM sound + and the sound on 1st carrier (i.e. FM mono or AM). + AMSEL=1: auto-mute will switch between NICAM sound + and the analog mono input (MONOIN pin). + If tda9874a decoder on your card has MONOIN pin not connected, then + use only tda9874_AMSEL=0 or don't specify this option at all. + For example: + card=65 (FlyVideo 2000S) - set AMSEL=1 or AMSEL=0 + card=72 (Prolink PV-BT878P rev.9B) - set AMSEL=0 only + +msp3400.o + +:: + + + The driver for the msp34xx sound processor chips. If you have a + stereo card, you probably want to insmod this one. + + insmod args: + debug=1/2 print some debug info to the syslog, + 2 is more verbose. + simple=1 Use the "short programming" method. Newer + msp34xx versions support this. You need this + for dbx stereo. Default is on if supported by + the chip. + once=1 Don't check the TV-stations Audio mode + every few seconds, but only once after + channel switches. + amsound=1 Audio carrier is AM/NICAM at 6.5 Mhz. This + should improve things for french people, the + carrier autoscan seems to work with FM only... + +tea6300.o - OBSOLETE (use tvaudio instead) + +:: + + The driver for the tea6300 fader chip. If you have a stereo + card and the msp3400.o doesn't work, you might want to try this + one. This chip is seen on most STB TV/FM cards (usually from + Gateway OEM sold surplus on auction sites). + + insmod args: + debug=1 print some debug info to the syslog. + +tda8425.o - OBSOLETE (use tvaudio instead) + +:: + + The driver for the tda8425 fader chip. This driver used to be + part of bttv.c, so if your sound used to work but does not + anymore, try loading this module. + + insmod args: + debug=1 print some debug info to the syslog. + +tda985x.o - OBSOLETE (use tvaudio instead) + +:: + + The driver for the tda9850/55 audio chips. + + insmod args: + debug=1 print some debug info to the syslog. + chip=9850/9855 set the chip type. + + +If the box freezes hard with bttv +--------------------------------- + +It might be a bttv driver bug. It also might be bad hardware. It also +might be something else ... + +Just mailing me "bttv freezes" isn't going to help much. This README +has a few hints how you can help to pin down the problem. + + +bttv bugs +~~~~~~~~~ + +If some version works and another doesn't it is likely to be a driver +bug. It is very helpful if you can tell where exactly it broke +(i.e. the last working and the first broken version). + +With a hard freeze you probably doesn't find anything in the logfiles. +The only way to capture any kernel messages is to hook up a serial +console and let some terminal application log the messages. /me uses +screen. See Documentation/serial-console.txt for details on setting +up a serial console. + +Read Documentation/oops-tracing.txt to learn how to get any useful +information out of a register+stack dump printed by the kernel on +protection faults (so-called "kernel oops"). + +If you run into some kind of deadlock, you can try to dump a call trace +for each process using sysrq-t (see Documentation/sysrq.txt). +This way it is possible to figure where *exactly* some process in "D" +state is stuck. + +I've seen reports that bttv 0.7.x crashes whereas 0.8.x works rock solid +for some people. Thus probably a small buglet left somewhere in bttv +0.7.x. I have no idea where exactly, it works stable for me and a lot of +other people. But in case you have problems with the 0.7.x versions you +can give 0.8.x a try ... + + +hardware bugs +~~~~~~~~~~~~~ + +Some hardware can't deal with PCI-PCI transfers (i.e. grabber => vga). +Sometimes problems show up with bttv just because of the high load on +the PCI bus. The bt848/878 chips have a few workarounds for known +incompatibilities, see README.quirks. + +Some folks report that increasing the pci latency helps too, +althrought I'm not sure whenever this really fixes the problems or +only makes it less likely to happen. Both bttv and btaudio have a +insmod option to set the PCI latency of the device. + +Some mainboard have problems to deal correctly with multiple devices +doing DMA at the same time. bttv + ide seems to cause this sometimes, +if this is the case you likely see freezes only with video and hard disk +access at the same time. Updating the IDE driver to get the latest and +greatest workarounds for hardware bugs might fix these problems. + + +other +~~~~~ + +If you use some binary-only yunk (like nvidia module) try to reproduce +the problem without. + +IRQ sharing is known to cause problems in some cases. It works just +fine in theory and many configurations. Neverless it might be worth a +try to shuffle around the PCI cards to give bttv another IRQ or make +it share the IRQ with some other piece of hardware. IRQ sharing with +VGA cards seems to cause trouble sometimes. I've also seen funny +effects with bttv sharing the IRQ with the ACPI bridge (and +apci-enabled kernel). + +Bttv quirks +----------- + +Below is what the bt878 data book says about the PCI bug compatibility +modes of the bt878 chip. + +The triton1 insmod option sets the EN_TBFX bit in the control register. +The vsfx insmod option does the same for EN_VSFX bit. If you have +stability problems you can try if one of these options makes your box +work solid. + +drivers/pci/quirks.c knows about these issues, this way these bits are +enabled automagically for known-buggy chipsets (look at the kernel +messages, bttv tells you). + +Normal PCI Mode +~~~~~~~~~~~~~~~ + +The PCI REQ signal is the logical-or of the incoming function requests. +The inter-nal GNT[0:1] signals are gated asynchronously with GNT and +demultiplexed by the audio request signal. Thus the arbiter defaults to +the video function at power-up and parks there during no requests for +bus access. This is desirable since the video will request the bus more +often. However, the audio will have highest bus access priority. Thus +the audio will have first access to the bus even when issuing a request +after the video request but before the PCI external arbiter has granted +access to the Bt879. Neither function can preempt the other once on the +bus. The duration to empty the entire video PCI FIFO onto the PCI bus is +very short compared to the bus access latency the audio PCI FIFO can +tolerate. + + +430FX Compatibility Mode +~~~~~~~~~~~~~~~~~~~~~~~~ + +When using the 430FX PCI, the following rules will ensure +compatibility: + + (1) Deassert REQ at the same time as asserting FRAME. + (2) Do not reassert REQ to request another bus transaction until after + finish-ing the previous transaction. + +Since the individual bus masters do not have direct control of REQ, a +simple logical-or of video and audio requests would violate the rules. +Thus, both the arbiter and the initiator contain 430FX compatibility +mode logic. To enable 430FX mode, set the EN_TBFX bit as indicated in +Device Control Register on page 104. + +When EN_TBFX is enabled, the arbiter ensures that the two compatibility +rules are satisfied. Before GNT is asserted by the PCI arbiter, this +internal arbiter may still logical-or the two requests. However, once +the GNT is issued, this arbiter must lock in its decision and now route +only the granted request to the REQ pin. The arbiter decision lock +happens regardless of the state of FRAME because it does not know when +FRAME will be asserted (typically - each initiator will assert FRAME on +the cycle following GNT). When FRAME is asserted, it is the initiator s +responsibility to remove its request at the same time. It is the +arbiters responsibility to allow this request to flow through to REQ and +not allow the other request to hold REQ asserted. The decision lock may +be removed at the end of the transaction: for example, when the bus is +idle (FRAME and IRDY). The arbiter decision may then continue +asynchronously until GNT is again asserted. + + +Interfacing with Non-PCI 2.1 Compliant Core Logic +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +A small percentage of core logic devices may start a bus transaction +during the same cycle that GNT is de-asserted. This is non PCI 2.1 +compliant. To ensure compatibility when using PCs with these PCI +controllers, the EN_VSFX bit must be enabled (refer to Device Control +Register on page 104). When in this mode, the arbiter does not pass GNT +to the internal functions unless REQ is asserted. This prevents a bus +transaction from starting the same cycle as GNT is de-asserted. This +also has the side effect of not being able to take advantage of bus +parking, thus lowering arbitration performance. The Bt879 drivers must +query for these non-compliant devices, and set the EN_VSFX bit only if +required. + +bttv and sound mini howto +------------------------- + +There are a lot of different bt848/849/878/879 based boards available. +Making video work often is not a big deal, because this is handled +completely by the bt8xx chip, which is common on all boards. But +sound is handled in slightly different ways on each board. + +To handle the grabber boards correctly, there is a array tvcards[] in +bttv-cards.c, which holds the information required for each board. +Sound will work only, if the correct entry is used (for video it often +makes no difference). The bttv driver prints a line to the kernel +log, telling which card type is used. Like this one: + + bttv0: model: BT848(Hauppauge old) [autodetected] + +You should verify this is correct. If it isn't, you have to pass the +correct board type as insmod argument, "insmod bttv card=2" for +example. The file CARDLIST has a list of valid arguments for card. +If your card isn't listed there, you might check the source code for +new entries which are not listed yet. If there isn't one for your +card, you can check if one of the existing entries does work for you +(just trial and error...). + +Some boards have an extra processor for sound to do stereo decoding +and other nice features. The msp34xx chips are used by Hauppauge for +example. If your board has one, you might have to load a helper +module like msp3400.o to make sound work. If there isn't one for the +chip used on your board: Bad luck. Start writing a new one. Well, +you might want to check the video4linux mailing list archive first... + +Of course you need a correctly installed soundcard unless you have the +speakers connected directly to the grabber board. Hint: check the +mixer settings too. ALSA for example has everything muted by default. + + +How sound works in detail +~~~~~~~~~~~~~~~~~~~~~~~~~ + +Still doesn't work? Looks like some driver hacking is required. +Below is a do-it-yourself description for you. + +The bt8xx chips have 32 general purpose pins, and registers to control +these pins. One register is the output enable register +(BT848_GPIO_OUT_EN), it says which pins are actively driven by the +bt848 chip. Another one is the data register (BT848_GPIO_DATA), where +you can get/set the status if these pins. They can be used for input +and output. + +Most grabber board vendors use these pins to control an external chip +which does the sound routing. But every board is a little different. +These pins are also used by some companies to drive remote control +receiver chips. Some boards use the i2c bus instead of the gpio pins +to connect the mux chip. + +As mentioned above, there is a array which holds the required +information for each known board. You basically have to create a new +line for your board. The important fields are these two: + +struct tvcard +{ + [ ... ] + u32 gpiomask; + u32 audiomux[6]; /* Tuner, Radio, external, internal, mute, stereo */ +}; + +gpiomask specifies which pins are used to control the audio mux chip. +The corresponding bits in the output enable register +(BT848_GPIO_OUT_EN) will be set as these pins must be driven by the +bt848 chip. + +The audiomux[] array holds the data values for the different inputs +(i.e. which pins must be high/low for tuner/mute/...). This will be +written to the data register (BT848_GPIO_DATA) to switch the audio +mux. + + +What you have to do is figure out the correct values for gpiomask and +the audiomux array. If you have Windows and the drivers four your +card installed, you might to check out if you can read these registers +values used by the windows driver. A tool to do this is available +from ftp://telepresence.dmem.strath.ac.uk/pub/bt848/winutil, but it +does'nt work with bt878 boards according to some reports I received. +Another one with bt878 support is available from +http://btwincap.sourceforge.net/Files/btspy2.00.zip + +You might also dig around in the *.ini files of the Windows applications. +You can have a look at the board to see which of the gpio pins are +connected at all and then start trial-and-error ... + + +Starting with release 0.7.41 bttv has a number of insmod options to +make the gpio debugging easier: + +bttv_gpio=0/1 enable/disable gpio debug messages +gpiomask=n set the gpiomask value +audiomux=i,j,... set the values of the audiomux array +audioall=a set the values of the audiomux array (one + value for all array elements, useful to check + out which effect the particular value has). + +The messages printed with bttv_gpio=1 look like this: + + bttv0: gpio: en=00000027, out=00000024 in=00ffffd8 [audio: off] + +en = output _en_able register (BT848_GPIO_OUT_EN) +out = _out_put bits of the data register (BT848_GPIO_DATA), + i.e. BT848_GPIO_DATA & BT848_GPIO_OUT_EN +in = _in_put bits of the data register, + i.e. BT848_GPIO_DATA & ~BT848_GPIO_OUT_EN + + + +Other elements of the tvcards array +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +If you are trying to make a new card work you might find it useful to +know what the other elements in the tvcards array are good for: + +video_inputs - # of video inputs the card has +audio_inputs - historical cruft, not used any more. +tuner - which input is the tuner +svhs - which input is svhs (all others are labeled composite) +muxsel - video mux, input->registervalue mapping +pll - same as pll= insmod option +tuner_type - same as tuner= insmod option +*_modulename - hint whenever some card needs this or that audio + module loaded to work properly. +has_radio - whenever this TV card has a radio tuner. +no_msp34xx - "1" disables loading of msp3400.o module +no_tda9875 - "1" disables loading of tda9875.o module +needs_tvaudio - set to "1" to load tvaudio.o module + +If some config item is specified both from the tvcards array and as +insmod option, the insmod option takes precedence. + +Cards +----- + +.. note:: + For a more updated list, please check + https://linuxtv.org/wiki/index.php/Hardware_Device_Information + +Supported cards: Bt848/Bt848a/Bt849/Bt878/Bt879 cards +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +All cards with Bt848/Bt848a/Bt849/Bt878/Bt879 and normal +Composite/S-VHS inputs are supported. Teletext and Intercast support +(PAL only) for ALL cards via VBI sample decoding in software. + +Some cards with additional multiplexing of inputs or other additional +fancy chips are only partially supported (unless specifications by the +card manufacturer are given). When a card is listed here it isn't +necessarily fully supported. + +All other cards only differ by additional components as tuners, sound +decoders, EEPROMs, teletext decoders ... + + +MATRIX Vision +~~~~~~~~~~~~~ + +MV-Delta +- Bt848A +- 4 Composite inputs, 1 S-VHS input (shared with 4th composite) +- EEPROM + +http://www.matrix-vision.de/ + +This card has no tuner but supports all 4 composite (1 shared with an +S-VHS input) of the Bt848A. +Very nice card if you only have satellite TV but several tuners connected +to the card via composite. + +Many thanks to Matrix-Vision for giving us 2 cards for free which made +Bt848a/Bt849 single crystal operation support possible!!! + + + +Miro/Pinnacle PCTV +~~~~~~~~~~~~~~~~~~ + +- Bt848 + some (all??) come with 2 crystals for PAL/SECAM and NTSC +- PAL, SECAM or NTSC TV tuner (Philips or TEMIC) +- MSP34xx sound decoder on add on board + decoder is supported but AFAIK does not yet work + (other sound MUX setting in GPIO port needed??? somebody who fixed this???) +- 1 tuner, 1 composite and 1 S-VHS input +- tuner type is autodetected + +http://www.miro.de/ +http://www.miro.com/ + + +Many thanks for the free card which made first NTSC support possible back +in 1997! + + +Hauppauge Win/TV pci +~~~~~~~~~~~~~~~~~~~~ + +There are many different versions of the Hauppauge cards with different +tuners (TV+Radio ...), teletext decoders. +Note that even cards with same model numbers have (depending on the revision) +different chips on it. + +- Bt848 (and others but always in 2 crystal operation???) + newer cards have a Bt878 + +- PAL, SECAM, NTSC or tuner with or without Radio support + +e.g.: + +- PAL: + + - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners + - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3 + +- NTSC: + + - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners + - TSA5518: no datasheet available on Philips site + +- Philips SAA5246 or SAA5284 ( or no) Teletext decoder chip + with buffer RAM (e.g. Winbond W24257AS-35: 32Kx8 CMOS static RAM) + SAA5246 (I2C 0x22) is supported + +- 256 bytes EEPROM: Microchip 24LC02B or Philips 8582E2Y + with configuration information + I2C address 0xa0 (24LC02B also responds to 0xa2-0xaf) + +- 1 tuner, 1 composite and (depending on model) 1 S-VHS input + +- 14052B: mux for selection of sound source + +- sound decoder: TDA9800, MSP34xx (stereo cards) + + +Askey CPH-Series +~~~~~~~~~~~~~~~~ +Developed by TelSignal(?), OEMed by many vendors (Typhoon, Anubis, Dynalink) + +- Card series: + - CPH01x: BT848 capture only + - CPH03x: BT848 + - CPH05x: BT878 with FM + - CPH06x: BT878 (w/o FM) + - CPH07x: BT878 capture only + +- TV standards: + - CPH0x0: NTSC-M/M + - CPH0x1: PAL-B/G + - CPH0x2: PAL-I/I + - CPH0x3: PAL-D/K + - CPH0x4: SECAM-L/L + - CPH0x5: SECAM-B/G + - CPH0x6: SECAM-D/K + - CPH0x7: PAL-N/N + - CPH0x8: PAL-B/H + - CPH0x9: PAL-M/M + +- CPH03x was often sold as "TV capturer". + +Identifying: + + #) 878 cards can be identified by PCI Subsystem-ID: + - 144f:3000 = CPH06x + - 144F:3002 = CPH05x w/ FM + - 144F:3005 = CPH06x_LC (w/o remote control) + #) The cards have a sticker with "CPH"-model on the back. + #) These cards have a number printed on the PCB just above the tuner metal box: + - "80-CP2000300-x" = CPH03X + - "80-CP2000500-x" = CPH05X + - "80-CP2000600-x" = CPH06X / CPH06x_LC + + Askey sells these cards as "Magic TView series", Brand "MagicXpress". + Other OEM often call these "Tview", "TView99" or else. + +Lifeview Flyvideo Series: +~~~~~~~~~~~~~~~~~~~~~~~~~ + +The naming of these series differs in time and space. + +Identifying: + #) Some models can be identified by PCI subsystem ID: + + - 1852:1852 = Flyvideo 98 FM + - 1851:1850 = Flyvideo 98 + - 1851:1851 = Flyvideo 98 EZ (capture only) + + #) There is a print on the PCB: + + - LR25 = Flyvideo (Zoran ZR36120, SAA7110A) + - LR26 Rev.N = Flyvideo II (Bt848) + - LR26 Rev.O = Flyvideo II (Bt878) + - LR37 Rev.C = Flyvideo EZ (Capture only, ZR36120 + SAA7110) + - LR38 Rev.A1= Flyvideo II EZ (Bt848 capture only) + - LR50 Rev.Q = Flyvideo 98 (w/eeprom and PCI subsystem ID) + - LR50 Rev.W = Flyvideo 98 (no eeprom) + - LR51 Rev.E = Flyvideo 98 EZ (capture only) + - LR90 = Flyvideo 2000 (Bt878) + - LR90 Flyvideo 2000S (Bt878) w/Stereo TV (Package incl. LR91 daughterboard) + - LR91 = Stereo daughter card for LR90 + - LR97 = Flyvideo DVBS + - LR99 Rev.E = Low profile card for OEM integration (only internal audio!) bt878 + - LR136 = Flyvideo 2100/3100 (Low profile, SAA7130/SAA7134) + - LR137 = Flyvideo DV2000/DV3000 (SAA7130/SAA7134 + IEEE1394) + - LR138 Rev.C= Flyvideo 2000 (SAA7130) + - LR138 Flyvideo 3000 (SAA7134) w/Stereo TV + - These exist in variations w/FM and w/Remote sometimes denoted + by suffixes "FM" and "R". + + #) You have a laptop (miniPCI card): + - Product = FlyTV Platinum Mini + - Model/Chip = LR212/saa7135 + + - Lifeview.com.tw states (Feb. 2002): + "The FlyVideo2000 and FlyVideo2000s product name have renamed to FlyVideo98." + Their Bt8x8 cards are listed as discontinued. + - Flyvideo 2000S was probably sold as Flyvideo 3000 in some contries(Europe?). + The new Flyvideo 2000/3000 are SAA7130/SAA7134 based. + +"Flyvideo II" had been the name for the 848 cards, nowadays (in Germany) +this name is re-used for LR50 Rev.W. + +The Lifeview website mentioned Flyvideo III at some time, but such a card +has not yet been seen (perhaps it was the german name for LR90 [stereo]). +These cards are sold by many OEMs too. + +FlyVideo A2 (Elta 8680)= LR90 Rev.F (w/Remote, w/o FM, stereo TV by tda9821) {Germany} + +Lifeview 3000 (Elta 8681) as sold by Plus(April 2002), Germany = LR138 w/ saa7134 + + +Typhoon TV card series: +~~~~~~~~~~~~~~~~~~~~~~~ + +These can be CPH, Flyvideo, Pixelview or KNC1 series. +Typhoon is the brand of Anubis. +Model 50680 got re-used, some model no. had different contents over time. + +Models: + + - 50680 "TV Tuner PCI Pal BG"(old,red package)=can be CPH03x(bt848) or CPH06x(bt878) + - 50680 "TV Tuner Pal BG" (blue package)= Pixelview PV-BT878P+ (Rev 9B) + - 50681 "TV Tuner PCI Pal I" (variant of 50680) + - 50682 "TView TV/FM Tuner Pal BG" = Flyvideo 98FM (LR50 Rev.Q) + + .. note:: + + The package has a picture of CPH05x (which would be a real TView) + + - 50683 "TV Tuner PCI SECAM" (variant of 50680) + - 50684 "TV Tuner Pal BG" = Pixelview 878TV(Rev.3D) + - 50686 "TV Tuner" = KNC1 TV Station + - 50687 "TV Tuner stereo" = KNC1 TV Station pro + - 50688 "TV Tuner RDS" (black package) = KNC1 TV Station RDS + - 50689 TV SAT DVB-S CARD CI PCI (SAA7146AH, SU1278?) = "KNC1 TV Station DVB-S" + - 50692 "TV/FM Tuner" (small PCB) + - 50694 TV TUNER CARD RDS (PHILIPS CHIPSET SAA7134HL) + - 50696 TV TUNER STEREO (PHILIPS CHIPSET SAA7134HL, MK3ME Tuner) + - 50804 PC-SAT TV/Audio Karte = Techni-PC-Sat (ZORAN 36120PQC, Tuner:Alps) + - 50866 TVIEW SAT RECEIVER+ADR + - 50868 "TV/FM Tuner Pal I" (variant of 50682) + - 50999 "TV/FM Tuner Secam" (variant of 50682) + +Guillemot +~~~~~~~~~ + +Models: + +- Maxi-TV PCI (ZR36120) +- Maxi TV Video 2 = LR50 Rev.Q (FI1216MF, PAL BG+SECAM) +- Maxi TV Video 3 = CPH064 (PAL BG + SECAM) + +Mentor +~~~~~~ + +Mentor TV card ("55-878TV-U1") = Pixelview 878TV(Rev.3F) (w/FM w/Remote) + +Prolink +~~~~~~~ + +- TV cards: + + - PixelView Play TV pro - (Model: PV-BT878P+ REV 8E) + - PixelView Play TV pro - (Model: PV-BT878P+ REV 9D) + - PixelView Play TV pro - (Model: PV-BT878P+ REV 4C / 8D / 10A ) + - PixelView Play TV - (Model: PV-BT848P+) + - 878TV - (Model: PV-BT878TV) + +- Multimedia TV packages (card + software pack): + + - PixelView Play TV Theater - (Model: PV-M4200) = PixelView Play TV pro + Software + - PixelView Play TV PAK - (Model: PV-BT878P+ REV 4E) + - PixelView Play TV/VCR - (Model: PV-M3200 REV 4C / 8D / 10A ) + - PixelView Studio PAK - (Model: M2200 REV 4C / 8D / 10A ) + - PixelView PowerStudio PAK - (Model: PV-M3600 REV 4E) + - PixelView DigitalVCR PAK - (Model: PV-M2400 REV 4C / 8D / 10A ) + - PixelView PlayTV PAK II (TV/FM card + usb camera) PV-M3800 + - PixelView PlayTV XP PV-M4700,PV-M4700(w/FM) + - PixelView PlayTV DVR PV-M4600 package contents:PixelView PlayTV pro, windvr & videoMail s/w + +- Further Cards: + + - PV-BT878P+rev.9B (Play TV Pro, opt. w/FM w/NICAM) + - PV-BT878P+rev.2F + - PV-BT878P Rev.1D (bt878, capture only) + + - XCapture PV-CX881P (cx23881) + - PlayTV HD PV-CX881PL+, PV-CX881PL+(w/FM) (cx23881) + + - DTV3000 PV-DTV3000P+ DVB-S CI = Twinhan VP-1030 + - DTV2000 DVB-S = Twinhan VP-1020 + +- Video Conferencing: + + - PixelView Meeting PAK - (Model: PV-BT878P) + - PixelView Meeting PAK Lite - (Model: PV-BT878P) + - PixelView Meeting PAK plus - (Model: PV-BT878P+rev 4C/8D/10A) + - PixelView Capture - (Model: PV-BT848P) + - PixelView PlayTV USB pro + - Model No. PV-NT1004+, PV-NT1004+ (w/FM) = NT1004 USB decoder chip + SAA7113 video decoder chip + +Dynalink +~~~~~~~~ + +These are CPH series. + +Phoebemicro +~~~~~~~~~~~ + +- TV Master = CPH030 or CPH060 +- TV Master FM = CPH050 + +Genius/Kye +~~~~~~~~~~ + +- Video Wonder/Genius Internet Video Kit = LR37 Rev.C +- Video Wonder Pro II (848 or 878) = LR26 + +Tekram +~~~~~~ + +- VideoCap C205 (Bt848) +- VideoCap C210 (zr36120 +Philips) +- CaptureTV M200 (ISA) +- CaptureTV M205 (Bt848) + +Lucky Star +~~~~~~~~~~ + +- Image World Conference TV = LR50 Rev. Q + +Leadtek +~~~~~~~ + +- WinView 601 (Bt848) +- WinView 610 (Zoran) +- WinFast2000 +- WinFast2000 XP + +Support for the Leadtek WinView 601 TV/FM +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Author of this section: Jon Tombs + +This card is basically the same as all the rest (Bt484A, Philips tuner), +the main difference is that they have attached a programmable attenuator to 3 +GPIO lines in order to give some volume control. They have also stuck an +infra-red remote control decoded on the board, I will add support for this +when I get time (it simple generates an interrupt for each key press, with +the key code is placed in the GPIO port). + +I don't yet have any application to test the radio support. The tuner +frequency setting should work but it is possible that the audio multiplexer +is wrong. If it doesn't work, send me email. + + +- No Thanks to Leadtek they refused to answer any questions about their +hardware. The driver was written by visual inspection of the card. If you +use this driver, send an email insult to them, and tell them you won't +continue buying their hardware unless they support Linux. + +- Little thanks to Princeton Technology Corp (http://www.princeton.com.tw) +who make the audio attenuator. Their publicly available data-sheet available +on their web site doesn't include the chip programming information! Hidden +on their server are the full data-sheets, but don't ask how I found it. + +To use the driver I use the following options, the tuner and pll settings might +be different in your country + +insmod videodev +insmod i2c scan=1 i2c_debug=0 verbose=0 +insmod tuner type=1 debug=0 +insmod bttv pll=1 radio=1 card=17 + + +KNC One +~~~~~~~ + +- TV-Station +- TV-Station SE (+Software Bundle) +- TV-Station pro (+TV stereo) +- TV-Station FM (+Radio) +- TV-Station RDS (+RDS) +- TV Station SAT (analog satellite) +- TV-Station DVB-S + +.. note:: newer Cards have saa7134, but model name stayed the same? + +Provideo +~~~~~~~~ + +- PV951 or PV-951 (also are sold as: + Boeder TV-FM Video Capture Card, + Titanmedia Supervision TV-2400, + Provideo PV951 TF, + 3DeMon PV951, + MediaForte TV-Vision PV951, + Yoko PV951, + Vivanco Tuner Card PCI Art.-Nr.: 68404, + ) now named PV-951T + +- Surveillance Series: + + - PV-141 + - PV-143 + - PV-147 + - PV-148 (capture only) + - PV-150 + - PV-151 + +- TV-FM Tuner Series: + + - PV-951TDV (tv tuner + 1394) + - PV-951T/TF + - PV-951PT/TF + - PV-956T/TF Low Profile + - PV-911 + +Highscreen +~~~~~~~~~~ + +Models: + +- TV Karte = LR50 Rev.S +- TV-Boostar = Terratec Terra TV+ Version 1.0 (Bt848, tda9821) "ceb105.pcb" + +Zoltrix +~~~~~~~ + +Models: + +- Face to Face Capture (Bt848 capture only) (PCB "VP-2848") +- Face To Face TV MAX (Bt848) (PCB "VP-8482 Rev1.3") +- Genie TV (Bt878) (PCB "VP-8790 Rev 2.1") +- Genie Wonder Pro + +AVerMedia +~~~~~~~~~ + +- AVer FunTV Lite (ISA, AV3001 chipset) "M101.C" +- AVerTV +- AVerTV Stereo +- AVerTV Studio (w/FM) +- AVerMedia TV98 with Remote +- AVerMedia TV/FM98 Stereo +- AVerMedia TVCAM98 +- TVCapture (Bt848) +- TVPhone (Bt848) +- TVCapture98 (="AVerMedia TV98" in USA) (Bt878) +- TVPhone98 (Bt878, w/FM) + +======== =========== =============== ======= ====== ======== ======================= +PCB PCI-ID Model-Name Eeprom Tuner Sound Country +======== =========== =============== ======= ====== ======== ======================= +M101.C ISA ! +M108-B Bt848 -- FR1236 US [#f2]_,[#f3]_ +M1A8-A Bt848 AVer TV-Phone FM1216 -- +M168-T 1461:0003 AVerTV Studio 48:17 FM1216 TDA9840T D [#f1]_ w/FM w/Remote +M168-U 1461:0004 TVCapture98 40:11 FI1216 -- D w/Remote +M168II-B 1461:0003 Medion MD9592 48:16 FM1216 TDA9873H D w/FM +======== =========== =============== ======= ====== ======== ======================= + +.. [#f1] Daughterboard MB68-A with TDA9820T and TDA9840T +.. [#f2] Sony NE41S soldered (stereo sound?) +.. [#f3] Daughterboard M118-A w/ pic 16c54 and 4 MHz quartz + +- US site has different drivers for (as of 09/2002): + + - EZ Capture/InterCam PCI (BT-848 chip) + - EZ Capture/InterCam PCI (BT-878 chip) + - TV-Phone (BT-848 chip) + - TV98 (BT-848 chip) + - TV98 With Remote (BT-848 chip) + - TV98 (BT-878 chip) + - TV98 With Remote (BT-878) + - TV/FM98 (BT-878 chip) + - AVerTV + - AverTV Stereo + - AVerTV Studio + +DE hat diverse Treiber fuer diese Modelle (Stand 09/2002): + + - TVPhone (848) mit Philips tuner FR12X6 (w/ FM radio) + - TVPhone (848) mit Philips tuner FM12X6 (w/ FM radio) + - TVCapture (848) w/Philips tuner FI12X6 + - TVCapture (848) non-Philips tuner + - TVCapture98 (Bt878) + - TVPhone98 (Bt878) + - AVerTV und TVCapture98 w/VCR (Bt 878) + - AVerTVStudio und TVPhone98 w/VCR (Bt878) + - AVerTV GO Serie (Kein SVideo Input) + - AVerTV98 (BT-878 chip) + - AVerTV98 mit Fernbedienung (BT-878 chip) + - AVerTV/FM98 (BT-878 chip) + + - VDOmate (www.averm.com.cn) = M168U ? + +Aimslab +~~~~~~~ + +Models: + +- Video Highway or "Video Highway TR200" (ISA) +- Video Highway Xtreme (aka "VHX") (Bt848, FM w/ TEA5757) + +IXMicro (former: IMS=Integrated Micro Solutions) +~~~~~~~ + +Models: + +- IXTV BT848 (=TurboTV) +- IXTV BT878 +- IMS TurboTV (Bt848) + +Lifetec/Medion/Tevion/Aldi +~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- LT9306/MD9306 = CPH061 +- LT9415/MD9415 = LR90 Rev.F or Rev.G +- MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H) +- MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner) +- MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner) + +Modular Technologies (www.modulartech.com) UK +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- MM100 PCTV (Bt848) +- MM201 PCTV (Bt878, Bt832) w/ Quartzsight camera +- MM202 PCTV (Bt878, Bt832, tda9874) +- MM205 PCTV (Bt878) +- MM210 PCTV (Bt878) (Galaxy TV, Galaxymedia ?) + +Terratec +~~~~~~~~ + +Models: + +- Terra TV+ Version 1.0 (Bt848), "ceb105.PCB" printed on the PCB, TDA9821 +- Terra TV+ Version 1.1 (Bt878), "LR74 Rev.E" printed on the PCB, TDA9821 +- Terra TValueRadio, "LR102 Rev.C" printed on the PCB +- Terra TV/Radio+ Version 1.0, "80-CP2830100-0" TTTV3 printed on the PCB, + "CPH010-E83" on the back, SAA6588T, TDA9873H +- Terra TValue Version BT878, "80-CP2830110-0 TTTV4" printed on the PCB, + "CPH011-D83" on back +- Terra TValue Version 1.0 "ceb105.PCB" (really identical to Terra TV+ Version 1.0) +- Terra TValue New Revision "LR102 Rec.C" +- Terra Active Radio Upgrade (tea5757h, saa6588t) + +- LR74 is a newer PCB revision of ceb105 (both incl. connector for Active Radio Upgrade) + +- Cinergy 400 (saa7134), "E877 11(S)", "PM820092D" printed on PCB +- Cinergy 600 (saa7134) + +Technisat +~~~~~~~~~ + +Models: + +- Discos ADR PC-Karte ISA (no TV!) +- Discos ADR PC-Karte PCI (probably no TV?) +- Techni-PC-Sat (Sat. analog) + Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A) +- Mediafocus I (zr36120/zr36125, drp3510, Sat. analog + ADR Radio) +- Mediafocus II (saa7146, Sat. analog) +- SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A) +- SkyStar 1 DVB (AV7110) = Technotrend Premium +- SkyStar 2 DVB (B2C2) (=Sky2PC) + +Siemens +~~~~~~~ + +Multimedia eXtension Board (MXB) (SAA7146, SAA7111) + +Powercolor +~~~~~~~~~~ + +Models: + +- MTV878 + Package comes with different contents: + a) pcb "MTV878" (CARD=75) + b) Pixelview Rev. 4_ +- MTV878R w/Remote Control +- MTV878F w/Remote Control w/FM radio + +Pinnacle +~~~~~~~~ + +PCTV models: + +- Mirovideo PCTV (Bt848) +- Mirovideo PCTV SE (Bt848) +- Mirovideo PCTV Pro (Bt848 + Daughterboard for TV Stereo and FM) +- Studio PCTV Rave (Bt848 Version = Mirovideo PCTV) +- Studio PCTV Rave (Bt878 package w/o infrared) +- Studio PCTV (Bt878) +- Studio PCTV Pro (Bt878 stereo w/ FM) +- Pinnacle PCTV (Bt878, MT2032) +- Pinnacle PCTV Pro (Bt878, MT2032) +- Pinncale PCTV Sat (bt878a, HM1821/1221) ["Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811"] +- Pinnacle PCTV Sat XE + +M(J)PEG capture and playback models: + +- DC1+ (ISA) +- DC10 (zr36057, zr36060, saa7110, adv7176) +- DC10+ (zr36067, zr36060, saa7110, adv7176) +- DC20 (ql16x24b,zr36050, zr36016, saa7110, saa7187 ...) +- DC30 (zr36057, zr36050, zr36016, vpx3220, adv7176, ad1843, tea6415, miro FST97A1) +- DC30+ (zr36067, zr36050, zr36016, vpx3220, adv7176) +- DC50 (zr36067, zr36050, zr36016, saa7112, adv7176 (2 pcs.?), ad1843, miro FST97A1, Lattice ???) + +Lenco +~~~~~ + +Models: + +- MXR-9565 (=Technisat Mediafocus?) +- MXR-9571 (Bt848) (=CPH031?) +- MXR-9575 +- MXR-9577 (Bt878) (=Prolink 878TV Rev.3x) +- MXTV-9578CP (Bt878) (= Prolink PV-BT878P+4E) + +Iomega +~~~~~~ + +Buz (zr36067, zr36060, saa7111, saa7185) + +LML +~~~ + LML33 (zr36067, zr36060, bt819, bt856) + +Grandtec +~~~~~~~~ + +Models: + +- Grand Video Capture (Bt848) +- Multi Capture Card (Bt878) + +Koutech +~~~~~~~ + +Models: + +- KW-606 (Bt848) +- KW-607 (Bt848 capture only) +- KW-606RSF +- KW-607A (capture only) +- KW-608 (Zoran capture only) + +IODATA (jp) +~~~~~~~~~~~ + +Models: + +- GV-BCTV/PCI +- GV-BCTV2/PCI +- GV-BCTV3/PCI +- GV-BCTV4/PCI +- GV-VCP/PCI (capture only) +- GV-VCP2/PCI (capture only) + +Canopus (jp) +~~~~~~~~~~~~ + +WinDVR = Kworld "KW-TVL878RF" + +www.sigmacom.co.kr +~~~~~~~~~~~~~~~~~~ + +Sigma Cyber TV II + +www.sasem.co.kr +~~~~~~~~~~~~~~~ + +Litte OnAir TV + +hama +~~~~ + +TV/Radio-Tuner Card, PCI (Model 44677) = CPH051 + +Sigma Designs +~~~~~~~~~~~~~ + +Hollywood plus (em8300, em9010, adv7175), (PCB "M340-10") MPEG DVD decoder + +Formac +~~~~~~ + +Models: + +- iProTV (Card for iMac Mezzanine slot, Bt848+SCSI) +- ProTV (Bt848) +- ProTV II = ProTV Stereo (Bt878) ["stereo" means FM stereo, tv is still mono] + +ATI +~~~ + +Models: + +- TV-Wonder +- TV-Wonder VE + +Diamond Multimedia +~~~~~~~~~~~~~~~~~~ + +DTV2000 (Bt848, tda9875) + +Aopen +~~~~~ + +- VA1000 Plus (w/ Stereo) +- VA1000 Lite +- VA1000 (=LR90) + +Intel +~~~~~ + +Models: + +- Smart Video Recorder (ISA full-length) +- Smart Video Recorder pro (ISA half-length) +- Smart Video Recorder III (Bt848) + +STB +~~~ + +Models: + +- STB Gateway 6000704 (bt878) +- STB Gateway 6000699 (bt848) +- STB Gateway 6000402 (bt848) +- STB TV130 PCI + +Videologic +~~~~~~~~~~ + +Models: + +- Captivator Pro/TV (ISA?) +- Captivator PCI/VC (Bt848 bundled with camera) (capture only) + +Technotrend +~~~~~~~~~~~~ + +Models: + +- TT-SAT PCI (PCB "Sat-PCI Rev.:1.3.1"; zr36125, vpx3225d, stc0056a, Tuner:BSKE6-155A +- TT-DVB-Sat + - revisions 1.1, 1.3, 1.5, 1.6 and 2.1 + - This card is sold as OEM from: + - Siemens DVB-s Card + - Hauppauge WinTV DVB-S + - Technisat SkyStar 1 DVB + - Galaxis DVB Sat + - Now this card is called TT-PCline Premium Family + - TT-Budget (saa7146, bsru6-701a) + This card is sold as OEM from: + - Hauppauge WinTV Nova + - Satelco Standard PCI (DVB-S) + - TT-DVB-C PCI + +Teles +~~~~~ + + DVB-s (Rev. 2.2, BSRV2-301A, data only?) + +Remote Vision +~~~~~~~~~~~~~ + +MX RV605 (Bt848 capture only) + +Boeder +~~~~~~ + +Models: + +- PC ChatCam (Model 68252) (Bt848 capture only) +- Tv/Fm Capture Card (Model 68404) = PV951 + +Media-Surfer (esc-kathrein.de) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- Sat-Surfer (ISA) +- Sat-Surfer PCI = Techni-PC-Sat +- Cable-Surfer 1 +- Cable-Surfer 2 +- Cable-Surfer PCI (zr36120) +- Audio-Surfer (ISA Radio card) + +Jetway (www.jetway.com.tw) +~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- JW-TV 878M +- JW-TV 878 = KWorld KW-TV878RF + +Galaxis +~~~~~~~ + +Models: + +- Galaxis DVB Card S CI +- Galaxis DVB Card C CI +- Galaxis DVB Card S +- Galaxis DVB Card C +- Galaxis plug.in S [neuer Name: Galaxis DVB Card S CI + +Hauppauge +~~~~~~~~~ + +Models: + +- many many WinTV models ... +- WinTV DVBs = Technotrend Premium 1.3 +- WinTV NOVA = Technotrend Budget 1.1 "S-DVB DATA" +- WinTV NOVA-CI "SDVBACI" +- WinTV Nova USB (=Technotrend USB 1.0) +- WinTV-Nexus-s (=Technotrend Premium 2.1 or 2.2) +- WinTV PVR +- WinTV PVR 250 +- WinTV PVR 450 + +US models + +-990 WinTV-PVR-350 (249USD) (iTVC15 chipset + radio) +-980 WinTV-PVR-250 (149USD) (iTVC15 chipset) +-880 WinTV-PVR-PCI (199USD) (KFIR chipset + bt878) +-881 WinTV-PVR-USB +-190 WinTV-GO +-191 WinTV-GO-FM +-404 WinTV +-401 WinTV-radio +-495 WinTV-Theater +-602 WinTV-USB +-621 WinTV-USB-FM +-600 USB-Live +-698 WinTV-HD +-697 WinTV-D +-564 WinTV-Nexus-S + +Deutsche Modelle: + +-603 WinTV GO +-719 WinTV Primio-FM +-718 WinTV PCI-FM +-497 WinTV Theater +-569 WinTV USB +-568 WinTV USB-FM +-882 WinTV PVR +-981 WinTV PVR 250 +-891 WinTV-PVR-USB +-541 WinTV Nova +-488 WinTV Nova-Ci +-564 WinTV-Nexus-s +-727 WinTV-DVB-c +-545 Common Interface +-898 WinTV-Nova-USB + +UK models: + +-607 WinTV Go +-693,793 WinTV Primio FM +-647,747 WinTV PCI FM +-498 WinTV Theater +-883 WinTV PVR +-893 WinTV PVR USB (Duplicate entry) +-566 WinTV USB (UK) +-573 WinTV USB FM +-429 Impact VCB (bt848) +-600 USB Live (Video-In 1x Comp, 1xSVHS) +-542 WinTV Nova +-717 WinTV DVB-S +-909 Nova-t PCI +-893 Nova-t USB (Duplicate entry) +-802 MyTV +-804 MyView +-809 MyVideo +-872 MyTV2Go FM +-546 WinTV Nova-S CI +-543 WinTV Nova +-907 Nova-S USB +-908 Nova-T USB +-717 WinTV Nexus-S +-157 DEC3000-s Standalone + USB + +Spain: + +-685 WinTV-Go +-690 WinTV-PrimioFM +-416 WinTV-PCI Nicam Estereo +-677 WinTV-PCI-FM +-699 WinTV-Theater +-683 WinTV-USB +-678 WinTV-USB-FM +-983 WinTV-PVR-250 +-883 WinTV-PVR-PCI +-993 WinTV-PVR-350 +-893 WinTV-PVR-USB +-728 WinTV-DVB-C PCI +-832 MyTV2Go +-869 MyTV2Go-FM +-805 MyVideo (USB) + + +Matrix-Vision +~~~~~~~~~~~~~ + +Models: + +- MATRIX-Vision MV-Delta +- MATRIX-Vision MV-Delta 2 +- MVsigma-SLC (Bt848) + +Conceptronic (.net) +~~~~~~~~~~~~~~~~~~~ + +Models: + +- TVCON FM, TV card w/ FM = CPH05x +- TVCON = CPH06x + +BestData +~~~~~~~~ + +Models: + +- HCC100 = VCC100rev1 + camera +- VCC100 rev1 (bt848) +- VCC100 rev2 (bt878) + +Gallant (www.gallantcom.com) www.minton.com.tw +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- Intervision IV-510 (capture only bt8x8) +- Intervision IV-550 (bt8x8) +- Intervision IV-100 (zoran) +- Intervision IV-1000 (bt8x8) + +Asonic (www.asonic.com.cn) (website down) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +SkyEye tv 878 + +Hoontech +~~~~~~~~ + +878TV/FM + +Teppro (www.itcteppro.com.tw) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- ITC PCITV (Card Ver 1.0) "Teppro TV1/TVFM1 Card" +- ITC PCITV (Card Ver 2.0) +- ITC PCITV (Card Ver 3.0) = "PV-BT878P+ (REV.9D)" +- ITC PCITV (Card Ver 4.0) +- TEPPRO IV-550 (For BT848 Main Chip) +- ITC DSTTV (bt878, satellite) +- ITC VideoMaker (saa7146, StreamMachine sm2110, tvtuner) "PV-SM2210P+ (REV:1C)" + +Kworld (www.kworld.com.tw) +~~~~~~~~~~~~~~~~~~~~~~~~~~ + +PC TV Station: + +- KWORLD KW-TV878R TV (no radio) +- KWORLD KW-TV878RF TV (w/ radio) +- KWORLD KW-TVL878RF (low profile) +- KWORLD KW-TV713XRF (saa7134) + + + MPEG TV Station (same cards as above plus WinDVR Software MPEG en/decoder) + +- KWORLD KW-TV878R -Pro TV (no Radio) +- KWORLD KW-TV878RF-Pro TV (w/ Radio) +- KWORLD KW-TV878R -Ultra TV (no Radio) +- KWORLD KW-TV878RF-Ultra TV (w/ Radio) + +JTT/ Justy Corp.(http://www.jtt.ne.jp/) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +JTT-02 (JTT TV) "TV watchmate pro" (bt848) + +ADS www.adstech.com +~~~~~~~~~~~~~~~~~~~ + +Models: + +- Channel Surfer TV ( CHX-950 ) +- Channel Surfer TV+FM ( CHX-960FM ) + +AVEC www.prochips.com +~~~~~~~~~~~~~~~~~~~~~ + +AVEC Intercapture (bt848, tea6320) + +NoBrand +~~~~~~~ + +TV Excel = Australian Name for "PV-BT878P+ 8E" or "878TV Rev.3_" + +Mach www.machspeed.com +~~~~~~~~~~~~~~~~~~~~~~ + +Mach TV 878 + +Eline www.eline-net.com/ +~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- Eline Vision TVMaster / TVMaster FM (ELV-TVM/ ELV-TVM-FM) = LR26 (bt878) +- Eline Vision TVMaster-2000 (ELV-TVM-2000, ELV-TVM-2000-FM)= LR138 (saa713x) + +Spirit +~~~~~~ + +- Spirit TV Tuner/Video Capture Card (bt848) + +Boser www.boser.com.tw +~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- HS-878 Mini PCI Capture Add-on Card +- HS-879 Mini PCI 3D Audio and Capture Add-on Card (w/ ES1938 Solo-1) + +Satelco www.citycom-gmbh.de, www.satelco.de +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- TV-FM =KNC1 saa7134 +- Standard PCI (DVB-S) = Technotrend Budget +- Standard PCI (DVB-S) w/ CI +- Satelco Highend PCI (DVB-S) = Technotrend Premium + + +Sensoray www.sensoray.com +~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- Sensoray 311 (PC/104 bus) +- Sensoray 611 (PCI) + +CEI (Chartered Electronics Industries Pte Ltd [CEI] [FCC ID HBY]) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- TV Tuner - HBY-33A-RAFFLES Brooktree Bt848KPF + Philips +- TV Tuner MG9910 - HBY33A-TVO CEI + Philips SAA7110 + OKI M548262 + ST STV8438CV +- Primetime TV (ISA) + - acquired by Singapore Technologies + - now operating as Chartered Semiconductor Manufacturing + - Manufacturer of video cards is listed as: + - Cogent Electronics Industries [CEI] + +AITech +~~~~~~ + +Models: + +- Wavewatcher TV (ISA) +- AITech WaveWatcher TV-PCI = can be LR26 (Bt848) or LR50 (BT878) +- WaveWatcher TVR-202 TV/FM Radio Card (ISA) + +MAXRON +~~~~~~ + +Maxron MaxTV/FM Radio (KW-TV878-FNT) = Kworld or JW-TV878-FBK + +www.ids-imaging.de +~~~~~~~~~~~~~~~~~~ + +Models: + +- Falcon Series (capture only) + In USA: http://www.theimagingsource.com/ +- DFG/LC1 + +www.sknet-web.co.jp +~~~~~~~~~~~~~~~~~~~ + +SKnet Monster TV (saa7134) + +A-Max www.amaxhk.com (Colormax, Amax, Napa) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +APAC Viewcomp 878 + +Cybertainment +~~~~~~~~~~~~~ + +Models: + +- CyberMail AV Video Email Kit w/ PCI Capture Card (capture only) +- CyberMail Xtreme + +These are Flyvideo + +VCR (http://www.vcrinc.com/) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Video Catcher 16 + +Twinhan +~~~~~~~ + +Models: + +- DST Card/DST-IP (bt878, twinhan asic) VP-1020 + - Sold as: + - KWorld DVBS Satellite TV-Card + - Powercolor DSTV Satellite Tuner Card + - Prolink Pixelview DTV2000 + - Provideo PV-911 Digital Satellite TV Tuner Card With Common Interface ? +- DST-CI Card (DVB Satellite) VP-1030 +- DCT Card (DVB cable) + +MSI +~~~ + +Models: + +- MSI TV@nywhere Tuner Card (MS-8876) (CX23881/883) Not Bt878 compatible. +- MS-8401 DVB-S + +Focus www.focusinfo.com +~~~~~~~~~~~~~~~~~~~~~~~ + +InVideo PCI (bt878) + +Sdisilk www.sdisilk.com/ +~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- SDI Silk 100 +- SDI Silk 200 SDI Input Card + +www.euresys.com +~~~~~~~~~~~~~~~ + +PICOLO series + +PMC/Pace +~~~~~~~~ + +www.pacecom.co.uk website closed + +Mercury www.kobian.com (UK and FR) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Models: + +- LR50 +- LR138RBG-Rx == LR138 + +TEC sound +~~~~~~~~~ + +TV-Mate = Zoltrix VP-8482 + +Though educated googling found: www.techmakers.com + +(package and manuals don't have any other manufacturer info) TecSound + +Lorenzen www.lorenzen.de +~~~~~~~~~~~~~~~~~~~~~~~~ + +SL DVB-S PCI = Technotrend Budget PCI (su1278 or bsru version) + +Origo (.uk) www.origo2000.com +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +PC TV Card = LR50 + +I/O Magic www.iomagic.com +~~~~~~~~~~~~~~~~~~~~~~~~~ + +PC PVR - Desktop TV Personal Video Recorder DR-PCTV100 = Pinnacle ROB2D-51009464 4.0 + Cyberlink PowerVCR II + +Arowana +~~~~~~~ + +TV-Karte / Poso Power TV (?) = Zoltrix VP-8482 (?) + +iTVC15 boards: +~~~~~~~~~~~~~ + +kuroutoshikou.com ITVC15 +yuan.com MPG160 PCI TV (Internal PCI MPEG2 encoder card plus TV-tuner) + +Asus www.asuscom.com +~~~~~~~~~~~~~~~~~~~~ + +Models: + +- Asus TV Tuner Card 880 NTSC (low profile, cx23880) +- Asus TV (saa7134) + +Hoontech +~~~~~~~~ + +http://www.hoontech.de/ + +- HART Vision 848 (H-ART Vision 848) +- HART Vision 878 (H-Art Vision 878) + + + +Chips used at bttv devices +-------------------------- + +- all boards: + + - Brooktree Bt848/848A/849/878/879: video capture chip + +- Board specific + + - Miro PCTV: + + - Philips or Temic Tuner + + - Hauppauge Win/TV pci (version 405): + + - Microchip 24LC02B or Philips 8582E2Y: + - 256 Byte EEPROM with configuration information + - I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf) + - Philips SAA5246AGP/E: Videotext decoder chip, I2C 0x22-0x23 + + - TDA9800: sound decoder + + - Winbond W24257AS-35: 32Kx8 CMOS static RAM (Videotext buffer mem) + + - 14052B: analog switch for selection of sound source + +- PAL: + + - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners + - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3 + +- NTSC: + + - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners + - TSA5518: no datasheet available on Philips site + +- STB TV pci: + + - ??? + - if you want better support for STB cards send me info! + Look at the board! What chips are on it? + + + + +Specs +----- +Philips http://www.Semiconductors.COM/pip/ +Conexant http://www.conexant.com/ +Micronas http://www.micronas.com/en/home/index.html + +Thanks +------ + +Many thanks to: + +- Markus Schroeder for information on the Bt848 + and tuner programming and his control program xtvc. + +- Martin Buck for his great Videotext + package. + +- Gerd Hoffmann for the MSP3400 support and the modular + I2C, tuner, ... support. + + +- MATRIX Vision for giving us 2 cards for free, which made support of + single crystal operation possible. + +- MIRO for providing a free PCTV card and detailed information about the + components on their cards. (E.g. how the tuner type is detected) + Without their card I could not have debugged the NTSC mode. + +- Hauppauge for telling how the sound input is selected and what components + they do and will use on their radio cards. + Also many thanks for faxing me the FM1216 data sheet. + +Contributors +------------ + +Michael Chu + AverMedia fix and more flexible card recognition + +Alan Cox + Video4Linux interface and 2.1.x kernel adaptation + +Chris Kleitsch + Hardware I2C + +Gerd Hoffmann + Radio card (ITT sound processor) + +bigfoot +Ragnar Hojland Espinosa + ConferenceTV card + + ++ many more (please mail me if you are missing in this list and would + like to be mentioned) diff --git a/Documentation/video4linux/bttv/Tuners b/Documentation/media/v4l-drivers/tuners.rst similarity index 100% rename from Documentation/video4linux/bttv/Tuners rename to Documentation/media/v4l-drivers/tuners.rst diff --git a/Documentation/video4linux/bttv/CONTRIBUTORS b/Documentation/video4linux/bttv/CONTRIBUTORS deleted file mode 100644 index eb41b2650860..000000000000 --- a/Documentation/video4linux/bttv/CONTRIBUTORS +++ /dev/null @@ -1,25 +0,0 @@ -Contributors to bttv: - -Michael Chu - AverMedia fix and more flexible card recognition - -Alan Cox - Video4Linux interface and 2.1.x kernel adaptation - -Chris Kleitsch - Hardware I2C - -Gerd Knorr - Radio card (ITT sound processor) - -bigfoot -Ragnar Hojland Espinosa - ConferenceTV card - - -+ many more (please mail me if you are missing in this list and would - like to be mentioned) - - - - diff --git a/Documentation/video4linux/bttv/Cards b/Documentation/video4linux/bttv/Cards deleted file mode 100644 index a8fb6e2d3c8b..000000000000 --- a/Documentation/video4linux/bttv/Cards +++ /dev/null @@ -1,960 +0,0 @@ - -Gunther Mayer's bttv card gallery (graphical version of this text file :-) -is available at: http://www.bttv-gallery.de/ - - -Supported cards: -Bt848/Bt848a/Bt849/Bt878/Bt879 cards ------------------------------------- - -All cards with Bt848/Bt848a/Bt849/Bt878/Bt879 and normal -Composite/S-VHS inputs are supported. Teletext and Intercast support -(PAL only) for ALL cards via VBI sample decoding in software. - -Some cards with additional multiplexing of inputs or other additional -fancy chips are only partially supported (unless specifications by the -card manufacturer are given). When a card is listed here it isn't -necessarily fully supported. - -All other cards only differ by additional components as tuners, sound -decoders, EEPROMs, teletext decoders ... - - -Unsupported Cards: ------------------- - -Cards with Zoran (ZR) or Philips (SAA) or ISA are not supported by -this driver. - - -MATRIX Vision -------------- - -MV-Delta -- Bt848A -- 4 Composite inputs, 1 S-VHS input (shared with 4th composite) -- EEPROM - -http://www.matrix-vision.de/ - -This card has no tuner but supports all 4 composite (1 shared with an -S-VHS input) of the Bt848A. -Very nice card if you only have satellite TV but several tuners connected -to the card via composite. - -Many thanks to Matrix-Vision for giving us 2 cards for free which made -Bt848a/Bt849 single crystal operation support possible!!! - - - -Miro/Pinnacle PCTV ------------------- - -- Bt848 - some (all??) come with 2 crystals for PAL/SECAM and NTSC -- PAL, SECAM or NTSC TV tuner (Philips or TEMIC) -- MSP34xx sound decoder on add on board - decoder is supported but AFAIK does not yet work - (other sound MUX setting in GPIO port needed??? somebody who fixed this???) -- 1 tuner, 1 composite and 1 S-VHS input -- tuner type is autodetected - -http://www.miro.de/ -http://www.miro.com/ - - -Many thanks for the free card which made first NTSC support possible back -in 1997! - - -Hauppauge Win/TV pci --------------------- - -There are many different versions of the Hauppauge cards with different -tuners (TV+Radio ...), teletext decoders. -Note that even cards with same model numbers have (depending on the revision) -different chips on it. - -- Bt848 (and others but always in 2 crystal operation???) - newer cards have a Bt878 -- PAL, SECAM, NTSC or tuner with or without Radio support - -e.g.: - PAL: - TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners - TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3 - - NTSC: - TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners - TSA5518: no datasheet available on Philips site -- Philips SAA5246 or SAA5284 ( or no) Teletext decoder chip - with buffer RAM (e.g. Winbond W24257AS-35: 32Kx8 CMOS static RAM) - SAA5246 (I2C 0x22) is supported -- 256 bytes EEPROM: Microchip 24LC02B or Philips 8582E2Y - with configuration information - I2C address 0xa0 (24LC02B also responds to 0xa2-0xaf) -- 1 tuner, 1 composite and (depending on model) 1 S-VHS input -- 14052B: mux for selection of sound source -- sound decoder: TDA9800, MSP34xx (stereo cards) - - -Askey CPH-Series ----------------- -Developed by TelSignal(?), OEMed by many vendors (Typhoon, Anubis, Dynalink) - - Card series: - CPH01x: BT848 capture only - CPH03x: BT848 - CPH05x: BT878 with FM - CPH06x: BT878 (w/o FM) - CPH07x: BT878 capture only - - TV standards: - CPH0x0: NTSC-M/M - CPH0x1: PAL-B/G - CPH0x2: PAL-I/I - CPH0x3: PAL-D/K - CPH0x4: SECAM-L/L - CPH0x5: SECAM-B/G - CPH0x6: SECAM-D/K - CPH0x7: PAL-N/N - CPH0x8: PAL-B/H - CPH0x9: PAL-M/M - - CPH03x was often sold as "TV capturer". - - Identifying: - 1) 878 cards can be identified by PCI Subsystem-ID: - 144f:3000 = CPH06x - 144F:3002 = CPH05x w/ FM - 144F:3005 = CPH06x_LC (w/o remote control) - 1) The cards have a sticker with "CPH"-model on the back. - 2) These cards have a number printed on the PCB just above the tuner metal box: - "80-CP2000300-x" = CPH03X - "80-CP2000500-x" = CPH05X - "80-CP2000600-x" = CPH06X / CPH06x_LC - - Askey sells these cards as "Magic TView series", Brand "MagicXpress". - Other OEM often call these "Tview", "TView99" or else. - -Lifeview Flyvideo Series: -------------------------- - The naming of these series differs in time and space. - - Identifying: - 1) Some models can be identified by PCI subsystem ID: - 1852:1852 = Flyvideo 98 FM - 1851:1850 = Flyvideo 98 - 1851:1851 = Flyvideo 98 EZ (capture only) - 2) There is a print on the PCB: - LR25 = Flyvideo (Zoran ZR36120, SAA7110A) - LR26 Rev.N = Flyvideo II (Bt848) - Rev.O = Flyvideo II (Bt878) - LR37 Rev.C = Flyvideo EZ (Capture only, ZR36120 + SAA7110) - LR38 Rev.A1= Flyvideo II EZ (Bt848 capture only) - LR50 Rev.Q = Flyvideo 98 (w/eeprom and PCI subsystem ID) - Rev.W = Flyvideo 98 (no eeprom) - LR51 Rev.E = Flyvideo 98 EZ (capture only) - LR90 = Flyvideo 2000 (Bt878) - Flyvideo 2000S (Bt878) w/Stereo TV (Package incl. LR91 daughterboard) - LR91 = Stereo daughter card for LR90 - LR97 = Flyvideo DVBS - LR99 Rev.E = Low profile card for OEM integration (only internal audio!) bt878 - LR136 = Flyvideo 2100/3100 (Low profile, SAA7130/SAA7134) - LR137 = Flyvideo DV2000/DV3000 (SAA7130/SAA7134 + IEEE1394) - LR138 Rev.C= Flyvideo 2000 (SAA7130) - or Flyvideo 3000 (SAA7134) w/Stereo TV - These exist in variations w/FM and w/Remote sometimes denoted - by suffixes "FM" and "R". - 3) You have a laptop (miniPCI card): - Product = FlyTV Platinum Mini - Model/Chip = LR212/saa7135 - - Lifeview.com.tw states (Feb. 2002): - "The FlyVideo2000 and FlyVideo2000s product name have renamed to FlyVideo98." - Their Bt8x8 cards are listed as discontinued. - Flyvideo 2000S was probably sold as Flyvideo 3000 in some contries(Europe?). - The new Flyvideo 2000/3000 are SAA7130/SAA7134 based. - - "Flyvideo II" had been the name for the 848 cards, nowadays (in Germany) - this name is re-used for LR50 Rev.W. - The Lifeview website mentioned Flyvideo III at some time, but such a card - has not yet been seen (perhaps it was the german name for LR90 [stereo]). - These cards are sold by many OEMs too. - - FlyVideo A2 (Elta 8680)= LR90 Rev.F (w/Remote, w/o FM, stereo TV by tda9821) {Germany} - Lifeview 3000 (Elta 8681) as sold by Plus(April 2002), Germany = LR138 w/ saa7134 - - -Typhoon TV card series: ------------------------ - These can be CPH, Flyvideo, Pixelview or KNC1 series. - Typhoon is the brand of Anubis. - Model 50680 got re-used, some model no. had different contents over time. - - Models: - 50680 "TV Tuner PCI Pal BG"(old,red package)=can be CPH03x(bt848) or CPH06x(bt878) - 50680 "TV Tuner Pal BG" (blue package)= Pixelview PV-BT878P+ (Rev 9B) - 50681 "TV Tuner PCI Pal I" (variant of 50680) - 50682 "TView TV/FM Tuner Pal BG" = Flyvideo 98FM (LR50 Rev.Q) - Note: The package has a picture of CPH05x (which would be a real TView) - 50683 "TV Tuner PCI SECAM" (variant of 50680) - 50684 "TV Tuner Pal BG" = Pixelview 878TV(Rev.3D) - 50686 "TV Tuner" = KNC1 TV Station - 50687 "TV Tuner stereo" = KNC1 TV Station pro - 50688 "TV Tuner RDS" (black package) = KNC1 TV Station RDS - 50689 TV SAT DVB-S CARD CI PCI (SAA7146AH, SU1278?) = "KNC1 TV Station DVB-S" - 50692 "TV/FM Tuner" (small PCB) - 50694 TV TUNER CARD RDS (PHILIPS CHIPSET SAA7134HL) - 50696 TV TUNER STEREO (PHILIPS CHIPSET SAA7134HL, MK3ME Tuner) - 50804 PC-SAT TV/Audio Karte = Techni-PC-Sat (ZORAN 36120PQC, Tuner:Alps) - 50866 TVIEW SAT RECEIVER+ADR - 50868 "TV/FM Tuner Pal I" (variant of 50682) - 50999 "TV/FM Tuner Secam" (variant of 50682) - - -Guillemot ---------- - Maxi-TV PCI (ZR36120) - Maxi TV Video 2 = LR50 Rev.Q (FI1216MF, PAL BG+SECAM) - Maxi TV Video 3 = CPH064 (PAL BG + SECAM) - -Mentor ------- - Mentor TV card ("55-878TV-U1") = Pixelview 878TV(Rev.3F) (w/FM w/Remote) - -Prolink -------- - TV cards: - PixelView Play TV pro - (Model: PV-BT878P+ REV 8E) - PixelView Play TV pro - (Model: PV-BT878P+ REV 9D) - PixelView Play TV pro - (Model: PV-BT878P+ REV 4C / 8D / 10A ) - PixelView Play TV - (Model: PV-BT848P+) - 878TV - (Model: PV-BT878TV) - - Multimedia TV packages (card + software pack): - PixelView Play TV Theater - (Model: PV-M4200) = PixelView Play TV pro + Software - PixelView Play TV PAK - (Model: PV-BT878P+ REV 4E) - PixelView Play TV/VCR - (Model: PV-M3200 REV 4C / 8D / 10A ) - PixelView Studio PAK - (Model: M2200 REV 4C / 8D / 10A ) - PixelView PowerStudio PAK - (Model: PV-M3600 REV 4E) - PixelView DigitalVCR PAK - (Model: PV-M2400 REV 4C / 8D / 10A ) - - PixelView PlayTV PAK II (TV/FM card + usb camera) PV-M3800 - PixelView PlayTV XP PV-M4700,PV-M4700(w/FM) - PixelView PlayTV DVR PV-M4600 package contents:PixelView PlayTV pro, windvr & videoMail s/w - - Further Cards: - PV-BT878P+rev.9B (Play TV Pro, opt. w/FM w/NICAM) - PV-BT878P+rev.2F - PV-BT878P Rev.1D (bt878, capture only) - - XCapture PV-CX881P (cx23881) - PlayTV HD PV-CX881PL+, PV-CX881PL+(w/FM) (cx23881) - - DTV3000 PV-DTV3000P+ DVB-S CI = Twinhan VP-1030 - DTV2000 DVB-S = Twinhan VP-1020 - - Video Conferencing: - PixelView Meeting PAK - (Model: PV-BT878P) - PixelView Meeting PAK Lite - (Model: PV-BT878P) - PixelView Meeting PAK plus - (Model: PV-BT878P+rev 4C/8D/10A) - PixelView Capture - (Model: PV-BT848P) - - PixelView PlayTV USB pro - Model No. PV-NT1004+, PV-NT1004+ (w/FM) = NT1004 USB decoder chip + SAA7113 video decoder chip - -Dynalink --------- - These are CPH series. - -Phoebemicro ------------ - TV Master = CPH030 or CPH060 - TV Master FM = CPH050 - -Genius/Kye ----------- - Video Wonder/Genius Internet Video Kit = LR37 Rev.C - Video Wonder Pro II (848 or 878) = LR26 - -Tekram ------- - VideoCap C205 (Bt848) - VideoCap C210 (zr36120 +Philips) - CaptureTV M200 (ISA) - CaptureTV M205 (Bt848) - -Lucky Star ----------- - Image World Conference TV = LR50 Rev. Q - -Leadtek -------- - WinView 601 (Bt848) - WinView 610 (Zoran) - WinFast2000 - WinFast2000 XP - -KNC One -------- - TV-Station - TV-Station SE (+Software Bundle) - TV-Station pro (+TV stereo) - TV-Station FM (+Radio) - TV-Station RDS (+RDS) - TV Station SAT (analog satellite) - TV-Station DVB-S - - newer Cards have saa7134, but model name stayed the same? - -Provideo --------- - PV951 or PV-951 (also are sold as: - Boeder TV-FM Video Capture Card - Titanmedia Supervision TV-2400 - Provideo PV951 TF - 3DeMon PV951 - MediaForte TV-Vision PV951 - Yoko PV951 - Vivanco Tuner Card PCI Art.-Nr.: 68404 - ) now named PV-951T - - Surveillance Series - PV-141 - PV-143 - PV-147 - PV-148 (capture only) - PV-150 - PV-151 - - TV-FM Tuner Series - PV-951TDV (tv tuner + 1394) - PV-951T/TF - PV-951PT/TF - PV-956T/TF Low Profile - PV-911 - -Highscreen ----------- - TV Karte = LR50 Rev.S - TV-Boostar = Terratec Terra TV+ Version 1.0 (Bt848, tda9821) "ceb105.pcb" - -Zoltrix -------- - Face to Face Capture (Bt848 capture only) (PCB "VP-2848") - Face To Face TV MAX (Bt848) (PCB "VP-8482 Rev1.3") - Genie TV (Bt878) (PCB "VP-8790 Rev 2.1") - Genie Wonder Pro - -AVerMedia ---------- - AVer FunTV Lite (ISA, AV3001 chipset) "M101.C" - AVerTV - AVerTV Stereo - AVerTV Studio (w/FM) - AVerMedia TV98 with Remote - AVerMedia TV/FM98 Stereo - AVerMedia TVCAM98 - TVCapture (Bt848) - TVPhone (Bt848) - TVCapture98 (="AVerMedia TV98" in USA) (Bt878) - TVPhone98 (Bt878, w/FM) - - PCB PCI-ID Model-Name Eeprom Tuner Sound Country - -------------------------------------------------------------------- - M101.C ISA ! - M108-B Bt848 -- FR1236 US (2),(3) - M1A8-A Bt848 AVer TV-Phone FM1216 -- - M168-T 1461:0003 AVerTV Studio 48:17 FM1216 TDA9840T D (1) w/FM w/Remote - M168-U 1461:0004 TVCapture98 40:11 FI1216 -- D w/Remote - M168II-B 1461:0003 Medion MD9592 48:16 FM1216 TDA9873H D w/FM - - (1) Daughterboard MB68-A with TDA9820T and TDA9840T - (2) Sony NE41S soldered (stereo sound?) - (3) Daughterboard M118-A w/ pic 16c54 and 4 MHz quartz - - US site has different drivers for (as of 09/2002): - EZ Capture/InterCam PCI (BT-848 chip) - EZ Capture/InterCam PCI (BT-878 chip) - TV-Phone (BT-848 chip) - TV98 (BT-848 chip) - TV98 With Remote (BT-848 chip) - TV98 (BT-878 chip) - TV98 With Remote (BT-878) - TV/FM98 (BT-878 chip) - AVerTV - AverTV Stereo - AVerTV Studio - - DE hat diverse Treiber fuer diese Modelle (Stand 09/2002): - TVPhone (848) mit Philips tuner FR12X6 (w/ FM radio) - TVPhone (848) mit Philips tuner FM12X6 (w/ FM radio) - TVCapture (848) w/Philips tuner FI12X6 - TVCapture (848) non-Philips tuner - TVCapture98 (Bt878) - TVPhone98 (Bt878) - AVerTV und TVCapture98 w/VCR (Bt 878) - AVerTVStudio und TVPhone98 w/VCR (Bt878) - AVerTV GO Serie (Kein SVideo Input) - AVerTV98 (BT-878 chip) - AVerTV98 mit Fernbedienung (BT-878 chip) - AVerTV/FM98 (BT-878 chip) - - VDOmate (www.averm.com.cn) = M168U ? - -Aimslab -------- - Video Highway or "Video Highway TR200" (ISA) - Video Highway Xtreme (aka "VHX") (Bt848, FM w/ TEA5757) - -IXMicro (former: IMS=Integrated Micro Solutions) -------- - IXTV BT848 (=TurboTV) - IXTV BT878 - IMS TurboTV (Bt848) - -Lifetec/Medion/Tevion/Aldi --------------------------- - LT9306/MD9306 = CPH061 - LT9415/MD9415 = LR90 Rev.F or Rev.G - MD9592 = Avermedia TVphone98 (PCI_ID=1461:0003), PCB-Rev=M168II-B (w/TDA9873H) - MD9717 = KNC One (Rev D4, saa7134, FM1216 MK2 tuner) - MD5044 = KNC One (Rev D4, saa7134, FM1216ME MK3 tuner) - -Modular Technologies (www.modulartech.com) UK ---------------------------------------------- - MM100 PCTV (Bt848) - MM201 PCTV (Bt878, Bt832) w/ Quartzsight camera - MM202 PCTV (Bt878, Bt832, tda9874) - MM205 PCTV (Bt878) - MM210 PCTV (Bt878) (Galaxy TV, Galaxymedia ?) - -Terratec --------- - Terra TV+ Version 1.0 (Bt848), "ceb105.PCB" printed on the PCB, TDA9821 - Terra TV+ Version 1.1 (Bt878), "LR74 Rev.E" printed on the PCB, TDA9821 - Terra TValueRadio, "LR102 Rev.C" printed on the PCB - Terra TV/Radio+ Version 1.0, "80-CP2830100-0" TTTV3 printed on the PCB, - "CPH010-E83" on the back, SAA6588T, TDA9873H - Terra TValue Version BT878, "80-CP2830110-0 TTTV4" printed on the PCB, - "CPH011-D83" on back - Terra TValue Version 1.0 "ceb105.PCB" (really identical to Terra TV+ Version 1.0) - Terra TValue New Revision "LR102 Rec.C" - Terra Active Radio Upgrade (tea5757h, saa6588t) - - LR74 is a newer PCB revision of ceb105 (both incl. connector for Active Radio Upgrade) - - Cinergy 400 (saa7134), "E877 11(S)", "PM820092D" printed on PCB - Cinergy 600 (saa7134) - -Technisat ---------- - Discos ADR PC-Karte ISA (no TV!) - Discos ADR PC-Karte PCI (probably no TV?) - Techni-PC-Sat (Sat. analog) - Rev 1.2 (zr36120, vpx3220, stv0030, saa5246, BSJE3-494A) - Mediafocus I (zr36120/zr36125, drp3510, Sat. analog + ADR Radio) - Mediafocus II (saa7146, Sat. analog) - SatADR Rev 2.1 (saa7146a, saa7113h, stv0056a, msp3400c, drp3510a, BSKE3-307A) - SkyStar 1 DVB (AV7110) = Technotrend Premium - SkyStar 2 DVB (B2C2) (=Sky2PC) - -Siemens -------- - Multimedia eXtension Board (MXB) (SAA7146, SAA7111) - -Powercolor ----------- - MTV878 - Package comes with different contents: - a) pcb "MTV878" (CARD=75) - b) Pixelview Rev. 4_ - MTV878R w/Remote Control - MTV878F w/Remote Control w/FM radio - -Pinnacle --------- - Mirovideo PCTV (Bt848) - Mirovideo PCTV SE (Bt848) - Mirovideo PCTV Pro (Bt848 + Daughterboard for TV Stereo and FM) - Studio PCTV Rave (Bt848 Version = Mirovideo PCTV) - Studio PCTV Rave (Bt878 package w/o infrared) - Studio PCTV (Bt878) - Studio PCTV Pro (Bt878 stereo w/ FM) - Pinnacle PCTV (Bt878, MT2032) - Pinnacle PCTV Pro (Bt878, MT2032) - Pinncale PCTV Sat (bt878a, HM1821/1221) ["Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811"] - Pinnacle PCTV Sat XE - - M(J)PEG capture and playback: - DC1+ (ISA) - DC10 (zr36057, zr36060, saa7110, adv7176) - DC10+ (zr36067, zr36060, saa7110, adv7176) - DC20 (ql16x24b,zr36050, zr36016, saa7110, saa7187 ...) - DC30 (zr36057, zr36050, zr36016, vpx3220, adv7176, ad1843, tea6415, miro FST97A1) - DC30+ (zr36067, zr36050, zr36016, vpx3220, adv7176) - DC50 (zr36067, zr36050, zr36016, saa7112, adv7176 (2 pcs.?), ad1843, miro FST97A1, Lattice ???) - -Lenco ------ - MXR-9565 (=Technisat Mediafocus?) - MXR-9571 (Bt848) (=CPH031?) - MXR-9575 - MXR-9577 (Bt878) (=Prolink 878TV Rev.3x) - MXTV-9578CP (Bt878) (= Prolink PV-BT878P+4E) - -Iomega ------- - Buz (zr36067, zr36060, saa7111, saa7185) - -LML ---- - LML33 (zr36067, zr36060, bt819, bt856) - -Grandtec --------- - Grand Video Capture (Bt848) - Multi Capture Card (Bt878) - -Koutech -------- - KW-606 (Bt848) - KW-607 (Bt848 capture only) - KW-606RSF - KW-607A (capture only) - KW-608 (Zoran capture only) - -IODATA (jp) ------- - GV-BCTV/PCI - GV-BCTV2/PCI - GV-BCTV3/PCI - GV-BCTV4/PCI - GV-VCP/PCI (capture only) - GV-VCP2/PCI (capture only) - -Canopus (jp) -------- - WinDVR = Kworld "KW-TVL878RF" - -www.sigmacom.co.kr ------------------- - Sigma Cyber TV II - -www.sasem.co.kr ---------------- - Litte OnAir TV - -hama ----- - TV/Radio-Tuner Card, PCI (Model 44677) = CPH051 - -Sigma Designs -------------- - Hollywood plus (em8300, em9010, adv7175), (PCB "M340-10") MPEG DVD decoder - -Formac ------- - iProTV (Card for iMac Mezzanine slot, Bt848+SCSI) - ProTV (Bt848) - ProTV II = ProTV Stereo (Bt878) ["stereo" means FM stereo, tv is still mono] - -ATI ---- - TV-Wonder - TV-Wonder VE - -Diamond Multimedia ------------------- - DTV2000 (Bt848, tda9875) - -Aopen ------ - VA1000 Plus (w/ Stereo) - VA1000 Lite - VA1000 (=LR90) - -Intel ------ - Smart Video Recorder (ISA full-length) - Smart Video Recorder pro (ISA half-length) - Smart Video Recorder III (Bt848) - -STB ---- - STB Gateway 6000704 (bt878) - STB Gateway 6000699 (bt848) - STB Gateway 6000402 (bt848) - STB TV130 PCI - -Videologic ----------- - Captivator Pro/TV (ISA?) - Captivator PCI/VC (Bt848 bundled with camera) (capture only) - -Technotrend ------------- - TT-SAT PCI (PCB "Sat-PCI Rev.:1.3.1"; zr36125, vpx3225d, stc0056a, Tuner:BSKE6-155A - TT-DVB-Sat - revisions 1.1, 1.3, 1.5, 1.6 and 2.1 - This card is sold as OEM from: - Siemens DVB-s Card - Hauppauge WinTV DVB-S - Technisat SkyStar 1 DVB - Galaxis DVB Sat - Now this card is called TT-PCline Premium Family - TT-Budget (saa7146, bsru6-701a) - This card is sold as OEM from: - Hauppauge WinTV Nova - Satelco Standard PCI (DVB-S) - TT-DVB-C PCI - -Teles ------ - DVB-s (Rev. 2.2, BSRV2-301A, data only?) - -Remote Vision -------------- - MX RV605 (Bt848 capture only) - -Boeder ------- - PC ChatCam (Model 68252) (Bt848 capture only) - Tv/Fm Capture Card (Model 68404) = PV951 - -Media-Surfer (esc-kathrein.de) -------------------------------- - Sat-Surfer (ISA) - Sat-Surfer PCI = Techni-PC-Sat - Cable-Surfer 1 - Cable-Surfer 2 - Cable-Surfer PCI (zr36120) - Audio-Surfer (ISA Radio card) - -Jetway (www.jetway.com.tw) --------------------------- - JW-TV 878M - JW-TV 878 = KWorld KW-TV878RF - -Galaxis -------- - Galaxis DVB Card S CI - Galaxis DVB Card C CI - Galaxis DVB Card S - Galaxis DVB Card C - Galaxis plug.in S [neuer Name: Galaxis DVB Card S CI - -Hauppauge ---------- - many many WinTV models ... - WinTV DVBs = Technotrend Premium 1.3 - WinTV NOVA = Technotrend Budget 1.1 "S-DVB DATA" - WinTV NOVA-CI "SDVBACI" - WinTV Nova USB (=Technotrend USB 1.0) - WinTV-Nexus-s (=Technotrend Premium 2.1 or 2.2) - WinTV PVR - WinTV PVR 250 - WinTV PVR 450 - - US models - 990 WinTV-PVR-350 (249USD) (iTVC15 chipset + radio) - 980 WinTV-PVR-250 (149USD) (iTVC15 chipset) - 880 WinTV-PVR-PCI (199USD) (KFIR chipset + bt878) - 881 WinTV-PVR-USB - 190 WinTV-GO - 191 WinTV-GO-FM - 404 WinTV - 401 WinTV-radio - 495 WinTV-Theater - 602 WinTV-USB - 621 WinTV-USB-FM - 600 USB-Live - 698 WinTV-HD - 697 WinTV-D - 564 WinTV-Nexus-S - - Deutsche Modelle - 603 WinTV GO - 719 WinTV Primio-FM - 718 WinTV PCI-FM - 497 WinTV Theater - 569 WinTV USB - 568 WinTV USB-FM - 882 WinTV PVR - 981 WinTV PVR 250 - 891 WinTV-PVR-USB - 541 WinTV Nova - 488 WinTV Nova-Ci - 564 WinTV-Nexus-s - 727 WinTV-DVB-c - 545 Common Interface - 898 WinTV-Nova-USB - - UK models - 607 WinTV Go - 693,793 WinTV Primio FM - 647,747 WinTV PCI FM - 498 WinTV Theater - 883 WinTV PVR - 893 WinTV PVR USB (Duplicate entry) - 566 WinTV USB (UK) - 573 WinTV USB FM - 429 Impact VCB (bt848) - 600 USB Live (Video-In 1x Comp, 1xSVHS) - 542 WinTV Nova - 717 WinTV DVB-S - 909 Nova-t PCI - 893 Nova-t USB (Duplicate entry) - 802 MyTV - 804 MyView - 809 MyVideo - 872 MyTV2Go FM - - - 546 WinTV Nova-S CI - 543 WinTV Nova - 907 Nova-S USB - 908 Nova-T USB - 717 WinTV Nexus-S - 157 DEC3000-s Standalone + USB - - Spain - 685 WinTV-Go - 690 WinTV-PrimioFM - 416 WinTV-PCI Nicam Estereo - 677 WinTV-PCI-FM - 699 WinTV-Theater - 683 WinTV-USB - 678 WinTV-USB-FM - 983 WinTV-PVR-250 - 883 WinTV-PVR-PCI - 993 WinTV-PVR-350 - 893 WinTV-PVR-USB - 728 WinTV-DVB-C PCI - 832 MyTV2Go - 869 MyTV2Go-FM - 805 MyVideo (USB) - - -Matrix-Vision -------------- - MATRIX-Vision MV-Delta - MATRIX-Vision MV-Delta 2 - MVsigma-SLC (Bt848) - -Conceptronic (.net) ------------- - TVCON FM, TV card w/ FM = CPH05x - TVCON = CPH06x - -BestData --------- - HCC100 = VCC100rev1 + camera - VCC100 rev1 (bt848) - VCC100 rev2 (bt878) - -Gallant (www.gallantcom.com) www.minton.com.tw ------------------------------------------------ - Intervision IV-510 (capture only bt8x8) - Intervision IV-550 (bt8x8) - Intervision IV-100 (zoran) - Intervision IV-1000 (bt8x8) - -Asonic (www.asonic.com.cn) (website down) ------------------------------------------ - SkyEye tv 878 - -Hoontech --------- - 878TV/FM - -Teppro (www.itcteppro.com.tw) ------------------------------ - ITC PCITV (Card Ver 1.0) "Teppro TV1/TVFM1 Card" - ITC PCITV (Card Ver 2.0) - ITC PCITV (Card Ver 3.0) = "PV-BT878P+ (REV.9D)" - ITC PCITV (Card Ver 4.0) - TEPPRO IV-550 (For BT848 Main Chip) - ITC DSTTV (bt878, satellite) - ITC VideoMaker (saa7146, StreamMachine sm2110, tvtuner) "PV-SM2210P+ (REV:1C)" - -Kworld (www.kworld.com.tw) --------------------------- - PC TV Station - KWORLD KW-TV878R TV (no radio) - KWORLD KW-TV878RF TV (w/ radio) - - KWORLD KW-TVL878RF (low profile) - - KWORLD KW-TV713XRF (saa7134) - - - MPEG TV Station (same cards as above plus WinDVR Software MPEG en/decoder) - KWORLD KW-TV878R -Pro TV (no Radio) - KWORLD KW-TV878RF-Pro TV (w/ Radio) - KWORLD KW-TV878R -Ultra TV (no Radio) - KWORLD KW-TV878RF-Ultra TV (w/ Radio) - - - -JTT/ Justy Corp.(http://www.jtt.ne.jp/) ---------------------------------------------------------------------- - JTT-02 (JTT TV) "TV watchmate pro" (bt848) - -ADS www.adstech.com -------------------- - Channel Surfer TV ( CHX-950 ) - Channel Surfer TV+FM ( CHX-960FM ) - -AVEC www.prochips.com ---------------------- - AVEC Intercapture (bt848, tea6320) - -NoBrand -------- - TV Excel = Australian Name for "PV-BT878P+ 8E" or "878TV Rev.3_" - -Mach www.machspeed.com ----- - Mach TV 878 - -Eline www.eline-net.com/ ------ - Eline Vision TVMaster / TVMaster FM (ELV-TVM/ ELV-TVM-FM) = LR26 (bt878) - Eline Vision TVMaster-2000 (ELV-TVM-2000, ELV-TVM-2000-FM)= LR138 (saa713x) - -Spirit ------- - Spirit TV Tuner/Video Capture Card (bt848) - -Boser www.boser.com.tw ------ - HS-878 Mini PCI Capture Add-on Card - HS-879 Mini PCI 3D Audio and Capture Add-on Card (w/ ES1938 Solo-1) - -Satelco www.citycom-gmbh.de, www.satelco.de -------- - TV-FM =KNC1 saa7134 - Standard PCI (DVB-S) = Technotrend Budget - Standard PCI (DVB-S) w/ CI - Satelco Highend PCI (DVB-S) = Technotrend Premium - - -Sensoray www.sensoray.com --------- - Sensoray 311 (PC/104 bus) - Sensoray 611 (PCI) - -CEI (Chartered Electronics Industries Pte Ltd [CEI] [FCC ID HBY]) ---- - TV Tuner - HBY-33A-RAFFLES Brooktree Bt848KPF + Philips - TV Tuner MG9910 - HBY33A-TVO CEI + Philips SAA7110 + OKI M548262 + ST STV8438CV - Primetime TV (ISA) - acquired by Singapore Technologies - now operating as Chartered Semiconductor Manufacturing - Manufacturer of video cards is listed as: - Cogent Electronics Industries [CEI] - -AITech ------- - Wavewatcher TV (ISA) - AITech WaveWatcher TV-PCI = can be LR26 (Bt848) or LR50 (BT878) - WaveWatcher TVR-202 TV/FM Radio Card (ISA) - -MAXRON ------- - Maxron MaxTV/FM Radio (KW-TV878-FNT) = Kworld or JW-TV878-FBK - -www.ids-imaging.de ------------------- - Falcon Series (capture only) - In USA: http://www.theimagingsource.com/ - DFG/LC1 - -www.sknet-web.co.jp -------------------- - SKnet Monster TV (saa7134) - -A-Max www.amaxhk.com (Colormax, Amax, Napa) -------------------- - APAC Viewcomp 878 - -Cybertainment -------------- - CyberMail AV Video Email Kit w/ PCI Capture Card (capture only) - CyberMail Xtreme - These are Flyvideo - -VCR (http://www.vcrinc.com/) ---- - Video Catcher 16 - -Twinhan -------- - DST Card/DST-IP (bt878, twinhan asic) VP-1020 - Sold as: - KWorld DVBS Satellite TV-Card - Powercolor DSTV Satellite Tuner Card - Prolink Pixelview DTV2000 - Provideo PV-911 Digital Satellite TV Tuner Card With Common Interface ? - DST-CI Card (DVB Satellite) VP-1030 - DCT Card (DVB cable) - -MSI ---- - MSI TV@nywhere Tuner Card (MS-8876) (CX23881/883) Not Bt878 compatible. - MS-8401 DVB-S - -Focus www.focusinfo.com ------ - InVideo PCI (bt878) - -Sdisilk www.sdisilk.com/ -------- - SDI Silk 100 - SDI Silk 200 SDI Input Card - -www.euresys.com - PICOLO series - -PMC/Pace -www.pacecom.co.uk website closed - -Mercury www.kobian.com (UK and FR) - LR50 - LR138RBG-Rx == LR138 - -TEC sound (package and manuals don't have any other manufacturer info) TecSound - Though educated googling found: www.techmakers.com - TV-Mate = Zoltrix VP-8482 - -Lorenzen www.lorenzen.de --------- - SL DVB-S PCI = Technotrend Budget PCI (su1278 or bsru version) - -Origo (.uk) www.origo2000.com - PC TV Card = LR50 - -I/O Magic www.iomagic.com ---------- - PC PVR - Desktop TV Personal Video Recorder DR-PCTV100 = Pinnacle ROB2D-51009464 4.0 + Cyberlink PowerVCR II - -Arowana -------- - TV-Karte / Poso Power TV (?) = Zoltrix VP-8482 (?) - -iTVC15 boards: -------------- -kuroutoshikou.com ITVC15 -yuan.com MPG160 PCI TV (Internal PCI MPEG2 encoder card plus TV-tuner) - -Asus www.asuscom.com - Asus TV Tuner Card 880 NTSC (low profile, cx23880) - Asus TV (saa7134) - -Hoontech --------- -http://www.hoontech.de/ - HART Vision 848 (H-ART Vision 848) - HART Vision 878 (H-Art Vision 878) diff --git a/Documentation/video4linux/bttv/ICs b/Documentation/video4linux/bttv/ICs deleted file mode 100644 index 611315f87c3e..000000000000 --- a/Documentation/video4linux/bttv/ICs +++ /dev/null @@ -1,37 +0,0 @@ -all boards: - -Brooktree Bt848/848A/849/878/879: video capture chip - - - -Miro PCTV: - -Philips or Temic Tuner - - - -Hauppauge Win/TV pci (version 405): - -Microchip 24LC02B or -Philips 8582E2Y: 256 Byte EEPROM with configuration information - I2C 0xa0-0xa1, (24LC02B also responds to 0xa2-0xaf) -Philips SAA5246AGP/E: Videotext decoder chip, I2C 0x22-0x23 -TDA9800: sound decoder -Winbond W24257AS-35: 32Kx8 CMOS static RAM (Videotext buffer mem) -14052B: analog switch for selection of sound source - -PAL: -TDA5737: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners -TSA5522: 1.4 GHz I2C-bus controlled synthesizer, I2C 0xc2-0xc3 - -NTSC: -TDA5731: VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners -TSA5518: no datasheet available on Philips site - - - -STB TV pci: - -??? -if you want better support for STB cards send me info! -Look at the board! What chips are on it? diff --git a/Documentation/video4linux/bttv/Insmod-options b/Documentation/video4linux/bttv/Insmod-options deleted file mode 100644 index 14c065fa23ef..000000000000 --- a/Documentation/video4linux/bttv/Insmod-options +++ /dev/null @@ -1,172 +0,0 @@ - -Note: "modinfo " prints various information about a kernel -module, among them a complete and up-to-date list of insmod options. -This list tends to be outdated because it is updated manually ... - -========================================================================== - -bttv.o - the bt848/878 (grabber chip) driver - - insmod args: - card=n card type, see CARDLIST for a list. - tuner=n tuner type, see CARDLIST for a list. - radio=0/1 card supports radio - pll=0/1/2 pll settings - 0: don't use PLL - 1: 28 MHz crystal installed - 2: 35 MHz crystal installed - - triton1=0/1 for Triton1 (+others) compatibility - vsfx=0/1 yet another chipset bug compatibility bit - see README.quirks for details on these two. - - bigendian=n Set the endianness of the gfx framebuffer. - Default is native endian. - fieldnr=0/1 Count fields. Some TV descrambling software - needs this, for others it only generates - 50 useless IRQs/sec. default is 0 (off). - autoload=0/1 autoload helper modules (tuner, audio). - default is 1 (on). - bttv_verbose=0/1/2 verbose level (at insmod time, while - looking at the hardware). default is 1. - bttv_debug=0/1 debug messages (for capture). - default is 0 (off). - irq_debug=0/1 irq handler debug messages. - default is 0 (off). - gbuffers=2-32 number of capture buffers for mmap'ed capture. - default is 4. - gbufsize= size of capture buffers. default and - maximum value is 0x208000 (~2MB) - no_overlay=0 Enable overlay on broken hardware. There - are some chipsets (SIS for example) which - are known to have problems with the PCI DMA - push used by bttv. bttv will disable overlay - by default on this hardware to avoid crashes. - With this insmod option you can override this. - no_overlay=1 Disable overlay. It should be used by broken - hardware that doesn't support PCI2PCI direct - transfers. - automute=0/1 Automatically mutes the sound if there is - no TV signal, on by default. You might try - to disable this if you have bad input signal - quality which leading to unwanted sound - dropouts. - chroma_agc=0/1 AGC of chroma signal, off by default. - adc_crush=0/1 Luminance ADC crush, on by default. - i2c_udelay= Allow reduce I2C speed. Default is 5 usecs - (meaning 66,67 Kbps). The default is the - maximum supported speed by kernel bitbang - algorithm. You may use lower numbers, if I2C - messages are lost (16 is known to work on - all supported cards). - - bttv_gpio=0/1 - gpiomask= - audioall= - audiomux= - See Sound-FAQ for a detailed description. - - remap, card, radio and pll accept up to four comma-separated arguments - (for multiple boards). - -tuner.o - The tuner driver. You need this unless you want to use only - with a camera or external tuner ... - - insmod args: - debug=1 print some debug info to the syslog - type=n type of the tuner chip. n as follows: - see CARDLIST for a complete list. - pal=[bdgil] select PAL variant (used for some tuners - only, important for the audio carrier). - -tvaudio.o - new, experimental module which is supported to provide a single - driver for all simple i2c audio control chips (tda/tea*). - - insmod args: - tda8425 = 1 enable/disable the support for the - tda9840 = 1 various chips. - tda9850 = 1 The tea6300 can't be autodetected and is - tda9855 = 1 therefore off by default, if you have - tda9873 = 1 this one on your card (STB uses these) - tda9874a = 1 you have to enable it explicitly. - tea6300 = 0 The two tda985x chips use the same i2c - tea6420 = 1 address and can't be disturgished from - pic16c54 = 1 each other, you might have to disable - the wrong one. - debug = 1 print debug messages - - insmod args for tda9874a: - tda9874a_SIF=1/2 select sound IF input pin (1 or 2) - (default is pin 1) - tda9874a_AMSEL=0/1 auto-mute select for NICAM (default=0) - Please read note 3 below! - tda9874a_STD=n select TV sound standard (0..8): - 0 - A2, B/G - 1 - A2, M (Korea) - 2 - A2, D/K (1) - 3 - A2, D/K (2) - 4 - A2, D/K (3) - 5 - NICAM, I - 6 - NICAM, B/G - 7 - NICAM, D/K (default) - 8 - NICAM, L - - Note 1: tda9874a supports both tda9874h (old) and tda9874a (new) chips. - Note 2: tda9874h/a and tda9875 (which is supported separately by - tda9875.o) use the same i2c address so both modules should not be - used at the same time. - Note 3: Using tda9874a_AMSEL option depends on your TV card design! - AMSEL=0: auto-mute will switch between NICAM sound - and the sound on 1st carrier (i.e. FM mono or AM). - AMSEL=1: auto-mute will switch between NICAM sound - and the analog mono input (MONOIN pin). - If tda9874a decoder on your card has MONOIN pin not connected, then - use only tda9874_AMSEL=0 or don't specify this option at all. - For example: - card=65 (FlyVideo 2000S) - set AMSEL=1 or AMSEL=0 - card=72 (Prolink PV-BT878P rev.9B) - set AMSEL=0 only - -msp3400.o - The driver for the msp34xx sound processor chips. If you have a - stereo card, you probably want to insmod this one. - - insmod args: - debug=1/2 print some debug info to the syslog, - 2 is more verbose. - simple=1 Use the "short programming" method. Newer - msp34xx versions support this. You need this - for dbx stereo. Default is on if supported by - the chip. - once=1 Don't check the TV-stations Audio mode - every few seconds, but only once after - channel switches. - amsound=1 Audio carrier is AM/NICAM at 6.5 Mhz. This - should improve things for french people, the - carrier autoscan seems to work with FM only... - -tea6300.o - OBSOLETE (use tvaudio instead) - The driver for the tea6300 fader chip. If you have a stereo - card and the msp3400.o doesn't work, you might want to try this - one. This chip is seen on most STB TV/FM cards (usually from - Gateway OEM sold surplus on auction sites). - - insmod args: - debug=1 print some debug info to the syslog. - -tda8425.o - OBSOLETE (use tvaudio instead) - The driver for the tda8425 fader chip. This driver used to be - part of bttv.c, so if your sound used to work but does not - anymore, try loading this module. - - insmod args: - debug=1 print some debug info to the syslog. - -tda985x.o - OBSOLETE (use tvaudio instead) - The driver for the tda9850/55 audio chips. - - insmod args: - debug=1 print some debug info to the syslog. - chip=9850/9855 set the chip type. diff --git a/Documentation/video4linux/bttv/MAKEDEV b/Documentation/video4linux/bttv/MAKEDEV deleted file mode 100644 index 093c0cd18042..000000000000 --- a/Documentation/video4linux/bttv/MAKEDEV +++ /dev/null @@ -1,27 +0,0 @@ -#!/bin/bash - -function makedev () { - - for dev in 0 1 2 3; do - echo "/dev/$1$dev: char 81 $[ $2 + $dev ]" - rm -f /dev/$1$dev - mknod /dev/$1$dev c 81 $[ $2 + $dev ] - chmod 666 /dev/$1$dev - done - - # symlink for default device - rm -f /dev/$1 - ln -s /dev/${1}0 /dev/$1 -} - -# see http://linux.bytesex.org/v4l2/API.html - -echo "*** new device names ***" -makedev video 0 -makedev radio 64 -makedev vbi 224 - -#echo "*** old device names (for compatibility only) ***" -#makedev bttv 0 -#makedev bttv-fm 64 -#makedev bttv-vbi 224 diff --git a/Documentation/video4linux/bttv/Modprobe.conf b/Documentation/video4linux/bttv/Modprobe.conf deleted file mode 100644 index 55f14650d8cd..000000000000 --- a/Documentation/video4linux/bttv/Modprobe.conf +++ /dev/null @@ -1,11 +0,0 @@ -# i2c -alias char-major-89 i2c-dev -options i2c-core i2c_debug=1 -options i2c-algo-bit bit_test=1 - -# bttv -alias char-major-81 videodev -alias char-major-81-0 bttv -options bttv card=2 radio=1 -options tuner debug=1 - diff --git a/Documentation/video4linux/bttv/Modules.conf b/Documentation/video4linux/bttv/Modules.conf deleted file mode 100644 index 8f258faf18f1..000000000000 --- a/Documentation/video4linux/bttv/Modules.conf +++ /dev/null @@ -1,14 +0,0 @@ -# For modern kernels (2.6 or above), this belongs in /etc/modprobe.d/*.conf -# For for 2.4 kernels or earlier, this belongs in /etc/modules.conf. - -# i2c -alias char-major-89 i2c-dev -options i2c-core i2c_debug=1 -options i2c-algo-bit bit_test=1 - -# bttv -alias char-major-81 videodev -alias char-major-81-0 bttv -options bttv card=2 radio=1 -options tuner debug=1 - diff --git a/Documentation/video4linux/bttv/PROBLEMS b/Documentation/video4linux/bttv/PROBLEMS deleted file mode 100644 index 2b8b0079f7c7..000000000000 --- a/Documentation/video4linux/bttv/PROBLEMS +++ /dev/null @@ -1,62 +0,0 @@ -- Start capturing by pressing "c" or by selecting it via a menu! - -- Start capturing by pressing "c" or by selecting it via a menu!!! - -- The memory of some S3 cards is not recognized right: - - First of all, if you are not using XFree-3.2 or newer, upgrade AT LEAST to - XFree-3.2A! This solved the problem for most people. - - Start up X11 like this: "XF86_S3 -probeonly" and write down where the - linear frame buffer is. - If it is different to the address found by bttv install bttv like this: - "insmod bttv vidmem=0xfb0" - if the linear frame buffer is at 0xfb000000 (i.e. omit the last 5 zeros!) - - Some S3 cards even take up 64MB of memory but only report 32MB to the BIOS. - If this 64MB area overlaps the IO memory of the Bt848 you also have to - remap this. E.g.: insmod bttv vidmem=0xfb0 remap=0xfa0 - - If the video memory is found at the right place and there are no address - conflicts but still no picture (or the computer even crashes), - try disabling features of your PCI chipset in the BIOS setup. - - Frank Kapahnke also reported that problems - with his S3 868 went away when he upgraded to XFree 3.2. - - -- I still only get a black picture with my S3 card! - - Even with XFree-3.2A some people have problems with their S3 cards - (mostly with Trio 64 but also with some others) - Get the free demo version of Accelerated X from www.xinside.com and try - bttv with it. bttv seems to work with most S3 cards with Accelerated X. - - Since I do not know much (better make that almost nothing) about VGA card - programming I do not know the reason for this. - Looks like XFree does something different when setting up the video memory? - Maybe somebody can enlighten me? - Would be nice if somebody could get this to work with XFree since - Accelerated X costs more than some of the grabber cards ... - - Better linear frame buffer support for S3 cards will probably be in - XFree 4.0. - -- Grabbing is not switched off when changing consoles with XFree. - That's because XFree and some AcceleratedX versions do not send unmap - events. - -- Some popup windows (e.g. of the window manager) are not refreshed. - - Disable backing store by starting X with the option "-bs" - -- When using 32 bpp in XFree or 24+8bpp mode in AccelX 3.1 the system - can sometimes lock up if you use more than 1 bt848 card at the same time. - You will always get pixel errors when e.g. using more than 1 card in full - screen mode. Maybe we need something faster than the PCI bus ... - - -- Some S3 cards and the Matrox Mystique will produce pixel errors with - full resolution in 32-bit mode. - -- Some video cards have problems with Accelerated X 4.1 diff --git a/Documentation/video4linux/bttv/README b/Documentation/video4linux/bttv/README deleted file mode 100644 index 7cbf4fb6cf31..000000000000 --- a/Documentation/video4linux/bttv/README +++ /dev/null @@ -1,90 +0,0 @@ - -Release notes for bttv -====================== - -You'll need at least these config options for bttv: - CONFIG_I2C=m - CONFIG_I2C_ALGOBIT=m - CONFIG_VIDEO_DEV=m - -The latest bttv version is available from http://bytesex.org/bttv/ - - -Make bttv work with your card ------------------------------ - -Just try "modprobe bttv" and see if that works. - -If it doesn't bttv likely could not autodetect your card and needs some -insmod options. The most important insmod option for bttv is "card=n" -to select the correct card type. If you get video but no sound you've -very likely specified the wrong (or no) card type. A list of supported -cards is in CARDLIST.bttv - -If bttv takes very long to load (happens sometimes with the cheap -cards which have no tuner), try adding this to your modules.conf: - options i2c-algo-bit bit_test=1 - -For the WinTV/PVR you need one firmware file from the driver CD: -hcwamc.rbf. The file is in the pvr45xxx.exe archive (self-extracting -zip file, unzip can unpack it). Put it into the /etc/pvr directory or -use the firm_altera= insmod option to point the driver to the -location of the file. - -If your card isn't listed in CARDLIST.bttv or if you have trouble making -audio work, you should read the Sound-FAQ. - - -Autodetecting cards -------------------- - -bttv uses the PCI Subsystem ID to autodetect the card type. lspci lists -the Subsystem ID in the second line, looks like this: - -00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02) - Subsystem: Hauppauge computer works Inc. WinTV/GO - Flags: bus master, medium devsel, latency 32, IRQ 5 - Memory at e2000000 (32-bit, prefetchable) [size=4K] - -only bt878-based cards can have a subsystem ID (which does not mean -that every card really has one). bt848 cards can't have a Subsystem -ID and therefore can't be autodetected. There is a list with the ID's -in bttv-cards.c (in case you are intrested or want to mail patches -with updates). - - -Still doesn't work? -------------------- - -I do NOT have a lab with 30+ different grabber boards and a -PAL/NTSC/SECAM test signal generator at home, so I often can't -reproduce your problems. This makes debugging very difficult for me. -If you have some knowledge and spare time, please try to fix this -yourself (patches very welcome of course...) You know: The linux -slogan is "Do it yourself". - -There is a mailing list: linux-media@vger.kernel.org -http://vger.kernel.org/vger-lists.html#linux-media - -If you have trouble with some specific TV card, try to ask there -instead of mailing me directly. The chance that someone with the -same card listens there is much higher... - -For problems with sound: There are a lot of different systems used -for TV sound all over the world. And there are also different chips -which decode the audio signal. Reports about sound problems ("stereo -does'nt work") are pretty useless unless you include some details -about your hardware and the TV sound scheme used in your country (or -at least the country you are living in). - - -Finally: If you mail some patches for bttv around the world (to -linux-kernel/Alan/Linus/...), please Cc: me. - - -Have fun with bttv, - - Gerd - --- -Gerd Knorr diff --git a/Documentation/video4linux/bttv/README.WINVIEW b/Documentation/video4linux/bttv/README.WINVIEW deleted file mode 100644 index c61cf2864287..000000000000 --- a/Documentation/video4linux/bttv/README.WINVIEW +++ /dev/null @@ -1,33 +0,0 @@ - -Support for the Leadtek WinView 601 TV/FM by Jon Tombs - -This card is basically the same as all the rest (Bt484A, Philips tuner), -the main difference is that they have attached a programmable attenuator to 3 -GPIO lines in order to give some volume control. They have also stuck an -infra-red remote control decoded on the board, I will add support for this -when I get time (it simple generates an interrupt for each key press, with -the key code is placed in the GPIO port). - -I don't yet have any application to test the radio support. The tuner -frequency setting should work but it is possible that the audio multiplexer -is wrong. If it doesn't work, send me email. - - -- No Thanks to Leadtek they refused to answer any questions about their -hardware. The driver was written by visual inspection of the card. If you -use this driver, send an email insult to them, and tell them you won't -continue buying their hardware unless they support Linux. - -- Little thanks to Princeton Technology Corp (http://www.princeton.com.tw) -who make the audio attenuator. Their publicly available data-sheet available -on their web site doesn't include the chip programming information! Hidden -on their server are the full data-sheets, but don't ask how I found it. - -To use the driver I use the following options, the tuner and pll settings might -be different in your country - -insmod videodev -insmod i2c scan=1 i2c_debug=0 verbose=0 -insmod tuner type=1 debug=0 -insmod bttv pll=1 radio=1 card=17 - diff --git a/Documentation/video4linux/bttv/README.freeze b/Documentation/video4linux/bttv/README.freeze deleted file mode 100644 index 5eddfa076cfb..000000000000 --- a/Documentation/video4linux/bttv/README.freeze +++ /dev/null @@ -1,74 +0,0 @@ - -If the box freezes hard with bttv ... -===================================== - -It might be a bttv driver bug. It also might be bad hardware. It also -might be something else ... - -Just mailing me "bttv freezes" isn't going to help much. This README -has a few hints how you can help to pin down the problem. - - -bttv bugs ---------- - -If some version works and another doesn't it is likely to be a driver -bug. It is very helpful if you can tell where exactly it broke -(i.e. the last working and the first broken version). - -With a hard freeze you probably doesn't find anything in the logfiles. -The only way to capture any kernel messages is to hook up a serial -console and let some terminal application log the messages. /me uses -screen. See Documentation/serial-console.txt for details on setting -up a serial console. - -Read Documentation/oops-tracing.txt to learn how to get any useful -information out of a register+stack dump printed by the kernel on -protection faults (so-called "kernel oops"). - -If you run into some kind of deadlock, you can try to dump a call trace -for each process using sysrq-t (see Documentation/sysrq.txt). -This way it is possible to figure where *exactly* some process in "D" -state is stuck. - -I've seen reports that bttv 0.7.x crashes whereas 0.8.x works rock solid -for some people. Thus probably a small buglet left somewhere in bttv -0.7.x. I have no idea where exactly, it works stable for me and a lot of -other people. But in case you have problems with the 0.7.x versions you -can give 0.8.x a try ... - - -hardware bugs -------------- - -Some hardware can't deal with PCI-PCI transfers (i.e. grabber => vga). -Sometimes problems show up with bttv just because of the high load on -the PCI bus. The bt848/878 chips have a few workarounds for known -incompatibilities, see README.quirks. - -Some folks report that increasing the pci latency helps too, -althrought I'm not sure whenever this really fixes the problems or -only makes it less likely to happen. Both bttv and btaudio have a -insmod option to set the PCI latency of the device. - -Some mainboard have problems to deal correctly with multiple devices -doing DMA at the same time. bttv + ide seems to cause this sometimes, -if this is the case you likely see freezes only with video and hard disk -access at the same time. Updating the IDE driver to get the latest and -greatest workarounds for hardware bugs might fix these problems. - - -other ------ - -If you use some binary-only yunk (like nvidia module) try to reproduce -the problem without. - -IRQ sharing is known to cause problems in some cases. It works just -fine in theory and many configurations. Neverless it might be worth a -try to shuffle around the PCI cards to give bttv another IRQ or make -it share the IRQ with some other piece of hardware. IRQ sharing with -VGA cards seems to cause trouble sometimes. I've also seen funny -effects with bttv sharing the IRQ with the ACPI bridge (and -apci-enabled kernel). - diff --git a/Documentation/video4linux/bttv/README.quirks b/Documentation/video4linux/bttv/README.quirks deleted file mode 100644 index 92e03929a6b2..000000000000 --- a/Documentation/video4linux/bttv/README.quirks +++ /dev/null @@ -1,83 +0,0 @@ - -Below is what the bt878 data book says about the PCI bug compatibility -modes of the bt878 chip. - -The triton1 insmod option sets the EN_TBFX bit in the control register. -The vsfx insmod option does the same for EN_VSFX bit. If you have -stability problems you can try if one of these options makes your box -work solid. - -drivers/pci/quirks.c knows about these issues, this way these bits are -enabled automagically for known-buggy chipsets (look at the kernel -messages, bttv tells you). - -HTH, - - Gerd - ----------------------------- cut here -------------------------- - -Normal PCI Mode ---------------- - -The PCI REQ signal is the logical-or of the incoming function requests. -The inter-nal GNT[0:1] signals are gated asynchronously with GNT and -demultiplexed by the audio request signal. Thus the arbiter defaults to -the video function at power-up and parks there during no requests for -bus access. This is desirable since the video will request the bus more -often. However, the audio will have highest bus access priority. Thus -the audio will have first access to the bus even when issuing a request -after the video request but before the PCI external arbiter has granted -access to the Bt879. Neither function can preempt the other once on the -bus. The duration to empty the entire video PCI FIFO onto the PCI bus is -very short compared to the bus access latency the audio PCI FIFO can -tolerate. - - -430FX Compatibility Mode ------------------------- - -When using the 430FX PCI, the following rules will ensure -compatibility: - - (1) Deassert REQ at the same time as asserting FRAME. - (2) Do not reassert REQ to request another bus transaction until after - finish-ing the previous transaction. - -Since the individual bus masters do not have direct control of REQ, a -simple logical-or of video and audio requests would violate the rules. -Thus, both the arbiter and the initiator contain 430FX compatibility -mode logic. To enable 430FX mode, set the EN_TBFX bit as indicated in -Device Control Register on page 104. - -When EN_TBFX is enabled, the arbiter ensures that the two compatibility -rules are satisfied. Before GNT is asserted by the PCI arbiter, this -internal arbiter may still logical-or the two requests. However, once -the GNT is issued, this arbiter must lock in its decision and now route -only the granted request to the REQ pin. The arbiter decision lock -happens regardless of the state of FRAME because it does not know when -FRAME will be asserted (typically - each initiator will assert FRAME on -the cycle following GNT). When FRAME is asserted, it is the initiator s -responsibility to remove its request at the same time. It is the -arbiters responsibility to allow this request to flow through to REQ and -not allow the other request to hold REQ asserted. The decision lock may -be removed at the end of the transaction: for example, when the bus is -idle (FRAME and IRDY). The arbiter decision may then continue -asynchronously until GNT is again asserted. - - -Interfacing with Non-PCI 2.1 Compliant Core Logic -------------------------------------------------- - -A small percentage of core logic devices may start a bus transaction -during the same cycle that GNT is de-asserted. This is non PCI 2.1 -compliant. To ensure compatibility when using PCs with these PCI -controllers, the EN_VSFX bit must be enabled (refer to Device Control -Register on page 104). When in this mode, the arbiter does not pass GNT -to the internal functions unless REQ is asserted. This prevents a bus -transaction from starting the same cycle as GNT is de-asserted. This -also has the side effect of not being able to take advantage of bus -parking, thus lowering arbitration performance. The Bt879 drivers must -query for these non-compliant devices, and set the EN_VSFX bit only if -required. - diff --git a/Documentation/video4linux/bttv/Sound-FAQ b/Documentation/video4linux/bttv/Sound-FAQ deleted file mode 100644 index 646a47de0016..000000000000 --- a/Documentation/video4linux/bttv/Sound-FAQ +++ /dev/null @@ -1,148 +0,0 @@ - -bttv and sound mini howto -========================= - -There are a lot of different bt848/849/878/879 based boards available. -Making video work often is not a big deal, because this is handled -completely by the bt8xx chip, which is common on all boards. But -sound is handled in slightly different ways on each board. - -To handle the grabber boards correctly, there is a array tvcards[] in -bttv-cards.c, which holds the information required for each board. -Sound will work only, if the correct entry is used (for video it often -makes no difference). The bttv driver prints a line to the kernel -log, telling which card type is used. Like this one: - - bttv0: model: BT848(Hauppauge old) [autodetected] - -You should verify this is correct. If it isn't, you have to pass the -correct board type as insmod argument, "insmod bttv card=2" for -example. The file CARDLIST has a list of valid arguments for card. -If your card isn't listed there, you might check the source code for -new entries which are not listed yet. If there isn't one for your -card, you can check if one of the existing entries does work for you -(just trial and error...). - -Some boards have an extra processor for sound to do stereo decoding -and other nice features. The msp34xx chips are used by Hauppauge for -example. If your board has one, you might have to load a helper -module like msp3400.o to make sound work. If there isn't one for the -chip used on your board: Bad luck. Start writing a new one. Well, -you might want to check the video4linux mailing list archive first... - -Of course you need a correctly installed soundcard unless you have the -speakers connected directly to the grabber board. Hint: check the -mixer settings too. ALSA for example has everything muted by default. - - -How sound works in detail -========================= - -Still doesn't work? Looks like some driver hacking is required. -Below is a do-it-yourself description for you. - -The bt8xx chips have 32 general purpose pins, and registers to control -these pins. One register is the output enable register -(BT848_GPIO_OUT_EN), it says which pins are actively driven by the -bt848 chip. Another one is the data register (BT848_GPIO_DATA), where -you can get/set the status if these pins. They can be used for input -and output. - -Most grabber board vendors use these pins to control an external chip -which does the sound routing. But every board is a little different. -These pins are also used by some companies to drive remote control -receiver chips. Some boards use the i2c bus instead of the gpio pins -to connect the mux chip. - -As mentioned above, there is a array which holds the required -information for each known board. You basically have to create a new -line for your board. The important fields are these two: - -struct tvcard -{ - [ ... ] - u32 gpiomask; - u32 audiomux[6]; /* Tuner, Radio, external, internal, mute, stereo */ -}; - -gpiomask specifies which pins are used to control the audio mux chip. -The corresponding bits in the output enable register -(BT848_GPIO_OUT_EN) will be set as these pins must be driven by the -bt848 chip. - -The audiomux[] array holds the data values for the different inputs -(i.e. which pins must be high/low for tuner/mute/...). This will be -written to the data register (BT848_GPIO_DATA) to switch the audio -mux. - - -What you have to do is figure out the correct values for gpiomask and -the audiomux array. If you have Windows and the drivers four your -card installed, you might to check out if you can read these registers -values used by the windows driver. A tool to do this is available -from ftp://telepresence.dmem.strath.ac.uk/pub/bt848/winutil, but it -does'nt work with bt878 boards according to some reports I received. -Another one with bt878 support is available from -http://btwincap.sourceforge.net/Files/btspy2.00.zip - -You might also dig around in the *.ini files of the Windows applications. -You can have a look at the board to see which of the gpio pins are -connected at all and then start trial-and-error ... - - -Starting with release 0.7.41 bttv has a number of insmod options to -make the gpio debugging easier: - -bttv_gpio=0/1 enable/disable gpio debug messages -gpiomask=n set the gpiomask value -audiomux=i,j,... set the values of the audiomux array -audioall=a set the values of the audiomux array (one - value for all array elements, useful to check - out which effect the particular value has). - -The messages printed with bttv_gpio=1 look like this: - - bttv0: gpio: en=00000027, out=00000024 in=00ffffd8 [audio: off] - -en = output _en_able register (BT848_GPIO_OUT_EN) -out = _out_put bits of the data register (BT848_GPIO_DATA), - i.e. BT848_GPIO_DATA & BT848_GPIO_OUT_EN -in = _in_put bits of the data register, - i.e. BT848_GPIO_DATA & ~BT848_GPIO_OUT_EN - - - -Other elements of the tvcards array -=================================== - -If you are trying to make a new card work you might find it useful to -know what the other elements in the tvcards array are good for: - -video_inputs - # of video inputs the card has -audio_inputs - historical cruft, not used any more. -tuner - which input is the tuner -svhs - which input is svhs (all others are labeled composite) -muxsel - video mux, input->registervalue mapping -pll - same as pll= insmod option -tuner_type - same as tuner= insmod option -*_modulename - hint whenever some card needs this or that audio - module loaded to work properly. -has_radio - whenever this TV card has a radio tuner. -no_msp34xx - "1" disables loading of msp3400.o module -no_tda9875 - "1" disables loading of tda9875.o module -needs_tvaudio - set to "1" to load tvaudio.o module - -If some config item is specified both from the tvcards array and as -insmod option, the insmod option takes precedence. - - - -Good luck, - - Gerd - - -PS: If you have a new working entry, mail it to me. - --- -Gerd Knorr diff --git a/Documentation/video4linux/bttv/Specs b/Documentation/video4linux/bttv/Specs deleted file mode 100644 index f32466cdae05..000000000000 --- a/Documentation/video4linux/bttv/Specs +++ /dev/null @@ -1,3 +0,0 @@ -Philips http://www.Semiconductors.COM/pip/ -Conexant http://www.conexant.com/ -Micronas http://www.micronas.com/en/home/index.html diff --git a/Documentation/video4linux/bttv/THANKS b/Documentation/video4linux/bttv/THANKS deleted file mode 100644 index 950aa781c2e9..000000000000 --- a/Documentation/video4linux/bttv/THANKS +++ /dev/null @@ -1,24 +0,0 @@ -Many thanks to: - -- Markus Schroeder for information on the Bt848 - and tuner programming and his control program xtvc. - -- Martin Buck for his great Videotext - package. - -- Gerd Knorr for the MSP3400 support and the modular - I2C, tuner, ... support. - - -- MATRIX Vision for giving us 2 cards for free, which made support of - single crystal operation possible. - -- MIRO for providing a free PCTV card and detailed information about the - components on their cards. (E.g. how the tuner type is detected) - Without their card I could not have debugged the NTSC mode. - -- Hauppauge for telling how the sound input is selected and what components - they do and will use on their radio cards. - Also many thanks for faxing me the FM1216 data sheet. - -