mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-18 17:54:13 +08:00
ARM: imx: initial SolidRun HummingBoard support
Add support for the SolidRun HummingBoard. This commit adds support for the following interfaces on this board: - Consumer Ir receiver - S/PDIF output - Both USB interfaces - Gigabit Ethernet using AR8035 - UART port Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This commit is contained in:
Russell King
parent
d8ec26d7f8
commit
208d7baf80
@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
|
||||
imx53-mba53.dtb \
|
||||
imx53-qsb.dtb \
|
||||
imx53-smd.dtb \
|
||||
imx6dl-hummingboard.dtb \
|
||||
imx6dl-sabreauto.dtb \
|
||||
imx6dl-sabresd.dtb \
|
||||
imx6dl-wandboard.dtb \
|
||||
|
||||
167
arch/arm/boot/dts/imx6dl-hummingboard.dts
Normal file
167
arch/arm/boot/dts/imx6dl-hummingboard.dts
Normal file
@ -0,0 +1,167 @@
|
||||
/*
|
||||
* Copyright (C) 2013,2014 Russell King
|
||||
*/
|
||||
/dts-v1/;
|
||||
|
||||
#include "imx6dl.dtsi"
|
||||
#include "imx6qdl-microsom.dtsi"
|
||||
#include "imx6qdl-microsom-ar8035.dtsi"
|
||||
|
||||
/ {
|
||||
model = "SolidRun HummingBoard DL/Solo";
|
||||
compatible = "solidrun,hummingboard", "fsl,imx6dl";
|
||||
|
||||
ir_recv: ir-receiver {
|
||||
compatible = "gpio-ir-receiver";
|
||||
gpios = <&gpio1 2 1>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_hummingboard_gpio1_2>;
|
||||
};
|
||||
|
||||
regulators {
|
||||
compatible = "simple-bus";
|
||||
|
||||
reg_3p3v: 3p3v {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "3P3V";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
reg_usbh1_vbus: usb-h1-vbus {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio1 0 0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_hummingboard_usbh1_vbus>;
|
||||
regulator-name = "usb_h1_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
|
||||
reg_usbotg_vbus: usb-otg-vbus {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio3 22 0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_hummingboard_usbotg_vbus>;
|
||||
regulator-name = "usb_otg_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
};
|
||||
|
||||
codec: spdif-transmitter {
|
||||
compatible = "linux,spdif-dit";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_hummingboard_spdif>;
|
||||
};
|
||||
|
||||
sound-spdif {
|
||||
compatible = "fsl,imx-audio-spdif";
|
||||
model = "imx-spdif";
|
||||
/* IMX6 doesn't implement this yet */
|
||||
spdif-controller = <&spdif>;
|
||||
spdif-out;
|
||||
};
|
||||
};
|
||||
|
||||
&can1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_hummingboard_flexcan1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_hummingboard_i2c1>;
|
||||
|
||||
/*
|
||||
* Not fitted on Carrier-1 board... yet
|
||||
status = "okay";
|
||||
|
||||
rtc: pcf8523@68 {
|
||||
compatible = "nxp,pcf8523";
|
||||
reg = <0x68>;
|
||||
};
|
||||
*/
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
hummingboard {
|
||||
pinctrl_hummingboard_flexcan1: hummingboard-flexcan1 {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
|
||||
MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_hummingboard_gpio1_2: hummingboard-gpio1_2 {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_hummingboard_i2c1: hummingboard-i2c1 {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
|
||||
MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_hummingboard_spdif: hummingboard-spdif {
|
||||
fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0>;
|
||||
};
|
||||
|
||||
pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
|
||||
fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
|
||||
};
|
||||
|
||||
pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
|
||||
fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
|
||||
};
|
||||
|
||||
pinctrl_hummingboard_usdhc2_aux: hummingboard-usdhc2-aux {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_hummingboard_usdhc2: hummingboard-usdhc2 {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
|
||||
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
|
||||
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
|
||||
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
|
||||
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
|
||||
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
|
||||
>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spdif {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh1 {
|
||||
vbus-supply = <®_usbh1_vbus>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbotg {
|
||||
vbus-supply = <®_usbotg_vbus>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usdhc2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <
|
||||
&pinctrl_hummingboard_usdhc2_aux
|
||||
&pinctrl_hummingboard_usdhc2
|
||||
>;
|
||||
vmmc-supply = <®_3p3v>;
|
||||
cd-gpios = <&gpio1 4 0>;
|
||||
status = "okay";
|
||||
};
|
||||
62
arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
Normal file
62
arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
Normal file
@ -0,0 +1,62 @@
|
||||
/*
|
||||
* Copyright (C) 2013,2014 Russell King
|
||||
*
|
||||
* This describes the hookup for an AR8035 to the iMX6 on the SolidRun
|
||||
* MicroSOM.
|
||||
*/
|
||||
&fec {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
|
||||
phy-mode = "rgmii";
|
||||
phy-reset-duration = <2>;
|
||||
phy-reset-gpios = <&gpio4 15 0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
enet {
|
||||
pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
|
||||
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
|
||||
/* AR8035 reset */
|
||||
MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0
|
||||
/* AR8035 interrupt */
|
||||
MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x80000000
|
||||
/* GPIO16 -> AR8035 25MHz */
|
||||
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0xc0000000
|
||||
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x80000000
|
||||
MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
|
||||
MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
|
||||
MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
|
||||
MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
|
||||
MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
|
||||
/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
|
||||
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x0a0b1
|
||||
/* AR8035 pin strapping: IO voltage: pull up */
|
||||
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
|
||||
/* AR8035 pin strapping: PHYADDR#0: pull down */
|
||||
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x130b0
|
||||
/* AR8035 pin strapping: PHYADDR#1: pull down */
|
||||
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x130b0
|
||||
/* AR8035 pin strapping: MODE#1: pull up */
|
||||
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
|
||||
/* AR8035 pin strapping: MODE#3: pull up */
|
||||
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
|
||||
/* AR8035 pin strapping: MODE#0: pull down */
|
||||
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x130b0
|
||||
|
||||
/*
|
||||
* As the RMII pins are also connected to RGMII
|
||||
* so that an AR8030 can be placed, set these
|
||||
* to high-z with the same pulls as above.
|
||||
* Use the GPIO settings to avoid changing the
|
||||
* input select registers.
|
||||
*/
|
||||
MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x03000
|
||||
MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x03000
|
||||
MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x03000
|
||||
>;
|
||||
};
|
||||
};
|
||||
};
|
||||
33
arch/arm/boot/dts/imx6qdl-microsom.dtsi
Normal file
33
arch/arm/boot/dts/imx6qdl-microsom.dtsi
Normal file
@ -0,0 +1,33 @@
|
||||
/*
|
||||
* Copyright (C) 2013,2014 Russell King
|
||||
*/
|
||||
|
||||
&iomuxc {
|
||||
microsom {
|
||||
pinctrl_microsom_uart1: microsom-uart1 {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
|
||||
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_microsom_usbotg: microsom-usbotg {
|
||||
/*
|
||||
* Similar to pinctrl_usbotg_2, but we want it
|
||||
* pulled down for a fixed host connection.
|
||||
*/
|
||||
fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_microsom_uart1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbotg {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_microsom_usbotg>;
|
||||
};
|
||||
@ -103,6 +103,39 @@ static int ar8031_phy_fixup(struct phy_device *dev)
|
||||
|
||||
#define PHY_ID_AR8031 0x004dd074
|
||||
|
||||
static int ar8035_phy_fixup(struct phy_device *dev)
|
||||
{
|
||||
u16 val;
|
||||
|
||||
/* Ar803x phy SmartEEE feature cause link status generates glitch,
|
||||
* which cause ethernet link down/up issue, so disable SmartEEE
|
||||
*/
|
||||
phy_write(dev, 0xd, 0x3);
|
||||
phy_write(dev, 0xe, 0x805d);
|
||||
phy_write(dev, 0xd, 0x4003);
|
||||
|
||||
val = phy_read(dev, 0xe);
|
||||
phy_write(dev, 0xe, val & ~(1 << 8));
|
||||
|
||||
/*
|
||||
* Enable 125MHz clock from CLK_25M on the AR8031. This
|
||||
* is fed in to the IMX6 on the ENET_REF_CLK (V22) pad.
|
||||
* Also, introduce a tx clock delay.
|
||||
*
|
||||
* This is the same as is the AR8031 fixup.
|
||||
*/
|
||||
ar8031_phy_fixup(dev);
|
||||
|
||||
/*check phy power*/
|
||||
val = phy_read(dev, 0x0);
|
||||
if (val & BMCR_PDOWN)
|
||||
phy_write(dev, 0x0, val & ~BMCR_PDOWN);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
#define PHY_ID_AR8035 0x004dd072
|
||||
|
||||
static void __init imx6q_enet_phy_init(void)
|
||||
{
|
||||
if (IS_BUILTIN(CONFIG_PHYLIB)) {
|
||||
@ -112,6 +145,8 @@ static void __init imx6q_enet_phy_init(void)
|
||||
ksz9031rn_phy_fixup);
|
||||
phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffff,
|
||||
ar8031_phy_fixup);
|
||||
phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,
|
||||
ar8035_phy_fixup);
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user