bnx2x: Remove support for emulation/FPGA

Remove unneeded support for emulation/FPGA from the code

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
Yaniv Rosner 2011-01-31 04:22:53 +00:00 committed by David S. Miller
parent 1bef68e3f5
commit 02a23165f8

View File

@ -521,22 +521,6 @@ static u8 bnx2x_emac_enable(struct link_params *params,
/* enable emac and not bmac */
REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 1);
/* for paladium */
if (CHIP_REV_IS_EMUL(bp)) {
/* Use lane 1 (of lanes 0-3) */
REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1);
REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1);
}
/* for fpga */
else
if (CHIP_REV_IS_FPGA(bp)) {
/* Use lane 1 (of lanes 0-3) */
DP(NETIF_MSG_LINK, "bnx2x_emac_enable: Setting FPGA\n");
REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1);
REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0);
} else
/* ASIC */
if (vars->phy_flags & PHY_XGXS_FLAG) {
u32 ser_lane = ((params->lane_config &
@ -654,15 +638,7 @@ static u8 bnx2x_emac_enable(struct link_params *params,
REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, val);
REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x1);
if (CHIP_REV_IS_EMUL(bp)) {
/* take the BigMac out of reset */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
(MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
/* enable access for bmac registers */
REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
} else
REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0);
REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0);
vars->mac_type = MAC_TYPE_EMAC;
return 0;
@ -1086,14 +1062,6 @@ static u8 bnx2x_bmac1_enable(struct link_params *params,
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS,
wb_data, 2);
/* fix for emulation */
if (CHIP_REV_IS_EMUL(bp)) {
wb_data[0] = 0xf000;
wb_data[1] = 0;
REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_PAUSE_THRESHOLD,
wb_data, 2);
}
return 0;
}
@ -7678,57 +7646,6 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars)
set_phy_vars(params);
DP(NETIF_MSG_LINK, "Num of phys on board: %d\n", params->num_phys);
if (CHIP_REV_IS_FPGA(bp)) {
vars->link_up = 1;
vars->line_speed = SPEED_10000;
vars->duplex = DUPLEX_FULL;
vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
vars->link_status = (LINK_STATUS_LINK_UP | LINK_10GTFD);
/* enable on E1.5 FPGA */
if (CHIP_IS_E1H(bp)) {
vars->flow_ctrl |=
(BNX2X_FLOW_CTRL_TX |
BNX2X_FLOW_CTRL_RX);
vars->link_status |=
(LINK_STATUS_TX_FLOW_CONTROL_ENABLED |
LINK_STATUS_RX_FLOW_CONTROL_ENABLED);
}
bnx2x_emac_enable(params, vars, 0);
if (!(CHIP_IS_E2(bp)))
bnx2x_pbf_update(params, vars->flow_ctrl,
vars->line_speed);
/* disable drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
/* update shared memory */
bnx2x_update_mng(params, vars->link_status);
return 0;
} else
if (CHIP_REV_IS_EMUL(bp)) {
vars->link_up = 1;
vars->line_speed = SPEED_10000;
vars->duplex = DUPLEX_FULL;
vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
vars->link_status = (LINK_STATUS_LINK_UP | LINK_10GTFD);
bnx2x_bmac_enable(params, vars, 0);
bnx2x_pbf_update(params, vars->flow_ctrl, vars->line_speed);
/* Disable drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE
+ params->port*4, 0);
/* update shared memory */
bnx2x_update_mng(params, vars->link_status);
return 0;
} else
if (params->loopback_mode == LOOPBACK_BMAC) {
vars->link_up = 1;
@ -8263,9 +8180,6 @@ u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[],
u32 ext_phy_type, ext_phy_config;
DP(NETIF_MSG_LINK, "Begin common phy init\n");
if (CHIP_REV_IS_EMUL(bp))
return 0;
/* Check if common init was already done */
phy_ver = REG_RD(bp, shmem_base_path[0] +
offsetof(struct shmem_region,