License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
|
|
|
/* SPDX-License-Identifier: GPL-2.0 */
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
#ifndef _VHOST_H
|
|
|
|
#define _VHOST_H
|
|
|
|
|
|
|
|
#include <linux/eventfd.h>
|
|
|
|
#include <linux/vhost.h>
|
|
|
|
#include <linux/mm.h>
|
|
|
|
#include <linux/mutex.h>
|
|
|
|
#include <linux/poll.h>
|
|
|
|
#include <linux/file.h>
|
|
|
|
#include <linux/uio.h>
|
|
|
|
#include <linux/virtio_config.h>
|
|
|
|
#include <linux/virtio_ring.h>
|
2011-07-27 07:09:06 +08:00
|
|
|
#include <linux/atomic.h>
|
2019-05-24 16:12:18 +08:00
|
|
|
#include <linux/pagemap.h>
|
|
|
|
#include <linux/mmu_notifier.h>
|
|
|
|
#include <asm/cacheflush.h>
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
|
2010-06-03 02:40:00 +08:00
|
|
|
struct vhost_work;
|
|
|
|
typedef void (*vhost_work_fn_t)(struct vhost_work *work);
|
|
|
|
|
2016-04-26 10:14:33 +08:00
|
|
|
#define VHOST_WORK_QUEUED 1
|
2010-06-03 02:40:00 +08:00
|
|
|
struct vhost_work {
|
2016-04-26 10:14:33 +08:00
|
|
|
struct llist_node node;
|
2010-06-03 02:40:00 +08:00
|
|
|
vhost_work_fn_t fn;
|
2016-04-26 10:14:33 +08:00
|
|
|
unsigned long flags;
|
2010-06-03 02:40:00 +08:00
|
|
|
};
|
|
|
|
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
/* Poll a file (eventfd or socket) */
|
|
|
|
/* Note: there's nothing vhost specific about this structure. */
|
|
|
|
struct vhost_poll {
|
|
|
|
poll_table table;
|
|
|
|
wait_queue_head_t *wqh;
|
2017-06-20 18:06:13 +08:00
|
|
|
wait_queue_entry_t wait;
|
2010-06-03 02:40:00 +08:00
|
|
|
struct vhost_work work;
|
2017-07-04 11:50:40 +08:00
|
|
|
__poll_t mask;
|
2010-06-03 02:40:00 +08:00
|
|
|
struct vhost_dev *dev;
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
};
|
|
|
|
|
2012-07-21 14:55:37 +08:00
|
|
|
void vhost_work_init(struct vhost_work *work, vhost_work_fn_t fn);
|
|
|
|
void vhost_work_queue(struct vhost_dev *dev, struct vhost_work *work);
|
2016-03-04 19:24:51 +08:00
|
|
|
bool vhost_has_work(struct vhost_dev *dev);
|
2012-07-21 14:55:37 +08:00
|
|
|
|
2010-06-03 02:40:00 +08:00
|
|
|
void vhost_poll_init(struct vhost_poll *poll, vhost_work_fn_t fn,
|
2017-07-04 11:50:40 +08:00
|
|
|
__poll_t mask, struct vhost_dev *dev);
|
2013-01-28 09:05:18 +08:00
|
|
|
int vhost_poll_start(struct vhost_poll *poll, struct file *file);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
void vhost_poll_stop(struct vhost_poll *poll);
|
|
|
|
void vhost_poll_flush(struct vhost_poll *poll);
|
|
|
|
void vhost_poll_queue(struct vhost_poll *poll);
|
2013-05-06 16:38:21 +08:00
|
|
|
void vhost_work_flush(struct vhost_dev *dev, struct vhost_work *work);
|
2018-03-15 01:05:06 +08:00
|
|
|
long vhost_vring_ioctl(struct vhost_dev *d, unsigned int ioctl, void __user *argp);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
|
|
|
|
struct vhost_log {
|
|
|
|
u64 addr;
|
|
|
|
u64 len;
|
|
|
|
};
|
|
|
|
|
2016-06-23 14:04:31 +08:00
|
|
|
#define START(node) ((node)->start)
|
|
|
|
#define LAST(node) ((node)->last)
|
|
|
|
|
|
|
|
struct vhost_umem_node {
|
|
|
|
struct rb_node rb;
|
|
|
|
struct list_head link;
|
|
|
|
__u64 start;
|
|
|
|
__u64 last;
|
|
|
|
__u64 size;
|
|
|
|
__u64 userspace_addr;
|
2016-06-23 14:04:32 +08:00
|
|
|
__u32 perm;
|
|
|
|
__u32 flags_padding;
|
2016-06-23 14:04:31 +08:00
|
|
|
__u64 __subtree_last;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct vhost_umem {
|
2017-09-09 07:15:08 +08:00
|
|
|
struct rb_root_cached umem_tree;
|
2016-06-23 14:04:31 +08:00
|
|
|
struct list_head umem_list;
|
2016-06-23 14:04:32 +08:00
|
|
|
int numem;
|
2016-06-23 14:04:31 +08:00
|
|
|
};
|
|
|
|
|
2017-02-28 17:56:02 +08:00
|
|
|
enum vhost_uaddr_type {
|
|
|
|
VHOST_ADDR_DESC = 0,
|
|
|
|
VHOST_ADDR_AVAIL = 1,
|
|
|
|
VHOST_ADDR_USED = 2,
|
|
|
|
VHOST_NUM_ADDRS = 3,
|
|
|
|
};
|
|
|
|
|
2019-05-24 16:12:18 +08:00
|
|
|
struct vhost_map {
|
|
|
|
int npages;
|
|
|
|
void *addr;
|
|
|
|
struct page **pages;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct vhost_uaddr {
|
|
|
|
unsigned long uaddr;
|
|
|
|
size_t size;
|
|
|
|
bool write;
|
|
|
|
};
|
|
|
|
|
2019-06-07 05:17:36 +08:00
|
|
|
#if defined(CONFIG_MMU_NOTIFIER) && ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE == 0
|
2019-07-26 19:49:29 +08:00
|
|
|
#define VHOST_ARCH_CAN_ACCEL_UACCESS 0
|
2019-06-07 05:17:36 +08:00
|
|
|
#else
|
|
|
|
#define VHOST_ARCH_CAN_ACCEL_UACCESS 0
|
|
|
|
#endif
|
2019-05-24 16:12:18 +08:00
|
|
|
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
/* The virtqueue structure describes a queue attached to a device. */
|
|
|
|
struct vhost_virtqueue {
|
|
|
|
struct vhost_dev *dev;
|
|
|
|
|
|
|
|
/* The actual ring of buffers. */
|
|
|
|
struct mutex mutex;
|
|
|
|
unsigned int num;
|
|
|
|
struct vring_desc __user *desc;
|
|
|
|
struct vring_avail __user *avail;
|
|
|
|
struct vring_used __user *used;
|
2019-05-24 16:12:18 +08:00
|
|
|
|
|
|
|
#if VHOST_ARCH_CAN_ACCEL_UACCESS
|
|
|
|
/* Read by memory accessors, modified by meta data
|
|
|
|
* prefetching, MMU notifier and vring ioctl().
|
|
|
|
* Synchonrized through mmu_lock (writers) and RCU (writers
|
|
|
|
* and readers).
|
|
|
|
*/
|
|
|
|
struct vhost_map __rcu *maps[VHOST_NUM_ADDRS];
|
|
|
|
/* Read by MMU notifier, modified by vring ioctl(),
|
|
|
|
* synchronized through MMU notifier
|
|
|
|
* registering/unregistering.
|
|
|
|
*/
|
|
|
|
struct vhost_uaddr uaddrs[VHOST_NUM_ADDRS];
|
|
|
|
#endif
|
2017-02-28 17:56:02 +08:00
|
|
|
const struct vhost_umem_node *meta_iotlb[VHOST_NUM_ADDRS];
|
2019-05-24 16:12:18 +08:00
|
|
|
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
struct file *kick;
|
|
|
|
struct eventfd_ctx *call_ctx;
|
|
|
|
struct eventfd_ctx *error_ctx;
|
|
|
|
struct eventfd_ctx *log_ctx;
|
|
|
|
|
|
|
|
struct vhost_poll poll;
|
|
|
|
|
|
|
|
/* The routine to call when the Guest pings us, or timeout. */
|
2010-06-03 02:40:00 +08:00
|
|
|
vhost_work_fn_t handle_kick;
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
|
|
|
|
/* Last available index we saw. */
|
|
|
|
u16 last_avail_idx;
|
|
|
|
|
|
|
|
/* Caches available index value from user. */
|
|
|
|
u16 avail_idx;
|
|
|
|
|
|
|
|
/* Last index we used. */
|
|
|
|
u16 last_used_idx;
|
|
|
|
|
|
|
|
/* Used flags */
|
|
|
|
u16 used_flags;
|
|
|
|
|
2011-05-20 07:10:54 +08:00
|
|
|
/* Last used index value we have signalled on */
|
|
|
|
u16 signalled_used;
|
|
|
|
|
|
|
|
/* Last used index value we have signalled on */
|
|
|
|
bool signalled_used_valid;
|
|
|
|
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
/* Log writes to used structure. */
|
|
|
|
bool log_used;
|
|
|
|
u64 log_addr;
|
|
|
|
|
2010-09-14 23:53:05 +08:00
|
|
|
struct iovec iov[UIO_MAXIOV];
|
2016-06-23 14:04:32 +08:00
|
|
|
struct iovec iotlb_iov[64];
|
2010-09-14 23:53:05 +08:00
|
|
|
struct iovec *indirect;
|
|
|
|
struct vring_used_elem *heads;
|
2013-05-07 14:54:36 +08:00
|
|
|
/* Protected by virtqueue mutex. */
|
2016-06-23 14:04:31 +08:00
|
|
|
struct vhost_umem *umem;
|
2016-06-23 14:04:32 +08:00
|
|
|
struct vhost_umem *iotlb;
|
2013-05-07 14:54:36 +08:00
|
|
|
void *private_data;
|
2014-10-24 19:08:18 +08:00
|
|
|
u64 acked_features;
|
2018-08-06 11:17:47 +08:00
|
|
|
u64 acked_backend_features;
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
/* Log write descriptors */
|
|
|
|
void __user *log_base;
|
2010-09-14 23:53:05 +08:00
|
|
|
struct vhost_log *log;
|
2015-04-24 20:27:24 +08:00
|
|
|
|
|
|
|
/* Ring endianness. Defaults to legacy native endianness.
|
|
|
|
* Set to true when starting a modern virtio device. */
|
|
|
|
bool is_le;
|
|
|
|
#ifdef CONFIG_VHOST_CROSS_ENDIAN_LEGACY
|
|
|
|
/* Ring endianness requested by userspace for cross-endian support. */
|
|
|
|
bool user_be;
|
|
|
|
#endif
|
2016-03-04 19:24:53 +08:00
|
|
|
u32 busyloop_timeout;
|
2019-05-24 16:12:18 +08:00
|
|
|
spinlock_t mmu_lock;
|
|
|
|
int invalidate_count;
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
};
|
|
|
|
|
2016-06-23 14:04:32 +08:00
|
|
|
struct vhost_msg_node {
|
2018-08-06 11:17:47 +08:00
|
|
|
union {
|
|
|
|
struct vhost_msg msg;
|
|
|
|
struct vhost_msg_v2 msg_v2;
|
|
|
|
};
|
2016-06-23 14:04:32 +08:00
|
|
|
struct vhost_virtqueue *vq;
|
|
|
|
struct list_head node;
|
|
|
|
};
|
|
|
|
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
struct vhost_dev {
|
|
|
|
struct mm_struct *mm;
|
2019-05-24 16:12:18 +08:00
|
|
|
#ifdef CONFIG_MMU_NOTIFIER
|
|
|
|
struct mmu_notifier mmu_notifier;
|
|
|
|
#endif
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
struct mutex mutex;
|
2013-04-27 11:16:48 +08:00
|
|
|
struct vhost_virtqueue **vqs;
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
int nvqs;
|
|
|
|
struct eventfd_ctx *log_ctx;
|
2016-04-26 10:14:33 +08:00
|
|
|
struct llist_head work_list;
|
2010-06-03 02:40:00 +08:00
|
|
|
struct task_struct *worker;
|
2016-06-23 14:04:31 +08:00
|
|
|
struct vhost_umem *umem;
|
2016-06-23 14:04:32 +08:00
|
|
|
struct vhost_umem *iotlb;
|
|
|
|
spinlock_t iotlb_lock;
|
|
|
|
struct list_head read_list;
|
|
|
|
struct list_head pending_list;
|
|
|
|
wait_queue_head_t wait;
|
2019-01-28 15:05:05 +08:00
|
|
|
int iov_limit;
|
2019-05-17 12:29:49 +08:00
|
|
|
int weight;
|
|
|
|
int byte_weight;
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
};
|
|
|
|
|
2019-05-17 12:29:49 +08:00
|
|
|
bool vhost_exceeds_weight(struct vhost_virtqueue *vq, int pkts, int total_len);
|
2019-01-28 15:05:05 +08:00
|
|
|
void vhost_dev_init(struct vhost_dev *, struct vhost_virtqueue **vqs,
|
2019-05-17 12:29:49 +08:00
|
|
|
int nvqs, int iov_limit, int weight, int byte_weight);
|
2013-05-06 11:15:59 +08:00
|
|
|
long vhost_dev_set_owner(struct vhost_dev *dev);
|
2013-06-06 20:20:39 +08:00
|
|
|
bool vhost_dev_has_owner(struct vhost_dev *dev);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
long vhost_dev_check_owner(struct vhost_dev *);
|
2016-06-23 14:04:31 +08:00
|
|
|
struct vhost_umem *vhost_dev_reset_owner_prepare(void);
|
|
|
|
void vhost_dev_reset_owner(struct vhost_dev *, struct vhost_umem *);
|
2017-12-25 00:08:58 +08:00
|
|
|
void vhost_dev_cleanup(struct vhost_dev *);
|
2012-11-01 17:16:46 +08:00
|
|
|
void vhost_dev_stop(struct vhost_dev *);
|
2012-12-06 20:03:34 +08:00
|
|
|
long vhost_dev_ioctl(struct vhost_dev *, unsigned int ioctl, void __user *argp);
|
2018-03-15 01:05:06 +08:00
|
|
|
long vhost_vring_ioctl(struct vhost_dev *d, unsigned int ioctl, void __user *argp);
|
2018-04-11 10:35:41 +08:00
|
|
|
bool vhost_vq_access_ok(struct vhost_virtqueue *vq);
|
|
|
|
bool vhost_log_access_ok(struct vhost_dev *);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
|
2014-06-05 20:20:27 +08:00
|
|
|
int vhost_get_vq_desc(struct vhost_virtqueue *,
|
2010-06-24 21:59:59 +08:00
|
|
|
struct iovec iov[], unsigned int iov_count,
|
|
|
|
unsigned int *out_num, unsigned int *in_num,
|
|
|
|
struct vhost_log *log, unsigned int *log_num);
|
2010-07-27 23:52:21 +08:00
|
|
|
void vhost_discard_vq_desc(struct vhost_virtqueue *, int n);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
|
2016-02-16 22:59:44 +08:00
|
|
|
int vhost_vq_init_access(struct vhost_virtqueue *);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
int vhost_add_used(struct vhost_virtqueue *, unsigned int head, int len);
|
2010-07-27 23:52:21 +08:00
|
|
|
int vhost_add_used_n(struct vhost_virtqueue *, struct vring_used_elem *heads,
|
|
|
|
unsigned count);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
void vhost_add_used_and_signal(struct vhost_dev *, struct vhost_virtqueue *,
|
2010-07-27 23:52:21 +08:00
|
|
|
unsigned int id, int len);
|
|
|
|
void vhost_add_used_and_signal_n(struct vhost_dev *, struct vhost_virtqueue *,
|
|
|
|
struct vring_used_elem *heads, unsigned count);
|
|
|
|
void vhost_signal(struct vhost_dev *, struct vhost_virtqueue *);
|
2011-05-20 07:10:54 +08:00
|
|
|
void vhost_disable_notify(struct vhost_dev *, struct vhost_virtqueue *);
|
2016-03-04 19:24:52 +08:00
|
|
|
bool vhost_vq_avail_empty(struct vhost_dev *, struct vhost_virtqueue *);
|
2011-05-20 07:10:54 +08:00
|
|
|
bool vhost_enable_notify(struct vhost_dev *, struct vhost_virtqueue *);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
|
|
|
|
int vhost_log_write(struct vhost_virtqueue *vq, struct vhost_log *log,
|
2019-01-16 16:54:42 +08:00
|
|
|
unsigned int log_num, u64 len,
|
|
|
|
struct iovec *iov, int count);
|
2019-05-24 16:12:15 +08:00
|
|
|
int vq_meta_prefetch(struct vhost_virtqueue *vq);
|
2016-06-23 14:04:32 +08:00
|
|
|
|
|
|
|
struct vhost_msg_node *vhost_new_msg(struct vhost_virtqueue *vq, int type);
|
|
|
|
void vhost_enqueue_msg(struct vhost_dev *dev,
|
|
|
|
struct list_head *head,
|
|
|
|
struct vhost_msg_node *node);
|
|
|
|
struct vhost_msg_node *vhost_dequeue_msg(struct vhost_dev *dev,
|
|
|
|
struct list_head *head);
|
2017-07-03 18:39:46 +08:00
|
|
|
__poll_t vhost_chr_poll(struct file *file, struct vhost_dev *dev,
|
2016-06-23 14:04:32 +08:00
|
|
|
poll_table *wait);
|
|
|
|
ssize_t vhost_chr_read_iter(struct vhost_dev *dev, struct iov_iter *to,
|
|
|
|
int noblock);
|
|
|
|
ssize_t vhost_chr_write_iter(struct vhost_dev *dev,
|
|
|
|
struct iov_iter *from);
|
|
|
|
int vhost_init_device_iotlb(struct vhost_dev *d, bool enabled);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
|
|
|
|
#define vq_err(vq, fmt, ...) do { \
|
|
|
|
pr_debug(pr_fmt(fmt), ##__VA_ARGS__); \
|
|
|
|
if ((vq)->error_ctx) \
|
|
|
|
eventfd_signal((vq)->error_ctx, 1);\
|
|
|
|
} while (0)
|
|
|
|
|
|
|
|
enum {
|
2011-05-20 07:10:54 +08:00
|
|
|
VHOST_FEATURES = (1ULL << VIRTIO_F_NOTIFY_ON_EMPTY) |
|
|
|
|
(1ULL << VIRTIO_RING_F_INDIRECT_DESC) |
|
|
|
|
(1ULL << VIRTIO_RING_F_EVENT_IDX) |
|
2015-09-10 03:24:56 +08:00
|
|
|
(1ULL << VHOST_F_LOG_ALL) |
|
|
|
|
(1ULL << VIRTIO_F_ANY_LAYOUT) |
|
|
|
|
(1ULL << VIRTIO_F_VERSION_1)
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
};
|
|
|
|
|
2014-10-24 19:08:18 +08:00
|
|
|
static inline bool vhost_has_feature(struct vhost_virtqueue *vq, int bit)
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
{
|
2014-10-24 19:08:18 +08:00
|
|
|
return vq->acked_features & (1ULL << bit);
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
}
|
2014-10-24 16:48:17 +08:00
|
|
|
|
2018-08-06 11:17:47 +08:00
|
|
|
static inline bool vhost_backend_has_feature(struct vhost_virtqueue *vq, int bit)
|
|
|
|
{
|
|
|
|
return vq->acked_backend_features & (1ULL << bit);
|
|
|
|
}
|
|
|
|
|
2015-10-27 17:37:39 +08:00
|
|
|
#ifdef CONFIG_VHOST_CROSS_ENDIAN_LEGACY
|
2015-04-24 20:25:12 +08:00
|
|
|
static inline bool vhost_is_little_endian(struct vhost_virtqueue *vq)
|
|
|
|
{
|
2015-04-24 20:27:24 +08:00
|
|
|
return vq->is_le;
|
2015-04-24 20:25:12 +08:00
|
|
|
}
|
2015-10-27 17:37:39 +08:00
|
|
|
#else
|
|
|
|
static inline bool vhost_is_little_endian(struct vhost_virtqueue *vq)
|
|
|
|
{
|
|
|
|
return virtio_legacy_is_little_endian() || vq->is_le;
|
|
|
|
}
|
|
|
|
#endif
|
2015-04-24 20:25:12 +08:00
|
|
|
|
2014-10-24 16:48:17 +08:00
|
|
|
/* Memory accessors */
|
|
|
|
static inline u16 vhost16_to_cpu(struct vhost_virtqueue *vq, __virtio16 val)
|
|
|
|
{
|
2015-04-24 20:25:12 +08:00
|
|
|
return __virtio16_to_cpu(vhost_is_little_endian(vq), val);
|
2014-10-24 16:48:17 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
static inline __virtio16 cpu_to_vhost16(struct vhost_virtqueue *vq, u16 val)
|
|
|
|
{
|
2015-04-24 20:25:12 +08:00
|
|
|
return __cpu_to_virtio16(vhost_is_little_endian(vq), val);
|
2014-10-24 16:48:17 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
static inline u32 vhost32_to_cpu(struct vhost_virtqueue *vq, __virtio32 val)
|
|
|
|
{
|
2015-04-24 20:25:12 +08:00
|
|
|
return __virtio32_to_cpu(vhost_is_little_endian(vq), val);
|
2014-10-24 16:48:17 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
static inline __virtio32 cpu_to_vhost32(struct vhost_virtqueue *vq, u32 val)
|
|
|
|
{
|
2015-04-24 20:25:12 +08:00
|
|
|
return __cpu_to_virtio32(vhost_is_little_endian(vq), val);
|
2014-10-24 16:48:17 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
static inline u64 vhost64_to_cpu(struct vhost_virtqueue *vq, __virtio64 val)
|
|
|
|
{
|
2015-04-24 20:25:12 +08:00
|
|
|
return __virtio64_to_cpu(vhost_is_little_endian(vq), val);
|
2014-10-24 16:48:17 +08:00
|
|
|
}
|
|
|
|
|
|
|
|
static inline __virtio64 cpu_to_vhost64(struct vhost_virtqueue *vq, u64 val)
|
|
|
|
{
|
2015-04-24 20:25:12 +08:00
|
|
|
return __cpu_to_virtio64(vhost_is_little_endian(vq), val);
|
2014-10-24 16:48:17 +08:00
|
|
|
}
|
vhost_net: a kernel-level virtio server
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14 14:17:27 +08:00
|
|
|
#endif
|