linux/mm/vmalloc.c

5131 lines
131 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 1993 Linus Torvalds
* Support of BIGMEM added by Gerhard Wichert, Siemens AG, July 1999
* SMP-safe vmalloc/vfree/ioremap, Tigran Aivazian <tigran@veritas.com>, May 2000
* Major rework to support vmap/vunmap, Christoph Hellwig, SGI, August 2002
* Numa awareness, Christoph Lameter, SGI, June 2005
* Improving global KVA allocator, Uladzislau Rezki, Sony, May 2019
*/
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
#include <linux/vmalloc.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/highmem.h>
sched/headers: Move task_struct::signal and task_struct::sighand types and accessors into <linux/sched/signal.h> task_struct::signal and task_struct::sighand are pointers, which would normally make it straightforward to not define those types in sched.h. That is not so, because the types are accompanied by a myriad of APIs (macros and inline functions) that dereference them. Split the types and the APIs out of sched.h and move them into a new header, <linux/sched/signal.h>. With this change sched.h does not know about 'struct signal' and 'struct sighand' anymore, trying to put accessors into sched.h as a test fails the following way: ./include/linux/sched.h: In function ‘test_signal_types’: ./include/linux/sched.h:2461:18: error: dereferencing pointer to incomplete type ‘struct signal_struct’ ^ This reduces the size and complexity of sched.h significantly. Update all headers and .c code that relied on getting the signal handling functionality from <linux/sched.h> to include <linux/sched/signal.h>. The list of affected files in the preparatory patch was partly generated by grepping for the APIs, and partly by doing coverage build testing, both all[yes|mod|def|no]config builds on 64-bit and 32-bit x86, and an array of cross-architecture builds. Nevertheless some (trivial) build breakage is still expected related to rare Kconfig combinations and in-flight patches to various kernel code, but most of it should be handled by this patch. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-02-02 15:35:14 +08:00
#include <linux/sched/signal.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#include <linux/interrupt.h>
#include <linux/proc_fs.h>
2008-04-28 17:12:40 +08:00
#include <linux/seq_file.h>
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
#include <linux/set_memory.h>
infrastructure to debug (dynamic) objects We can see an ever repeating problem pattern with objects of any kind in the kernel: 1) freeing of active objects 2) reinitialization of active objects Both problems can be hard to debug because the crash happens at a point where we have no chance to decode the root cause anymore. One problem spot are kernel timers, where the detection of the problem often happens in interrupt context and usually causes the machine to panic. While working on a timer related bug report I had to hack specialized code into the timer subsystem to get a reasonable hint for the root cause. This debug hack was fine for temporary use, but far from a mergeable solution due to the intrusiveness into the timer code. The code further lacked the ability to detect and report the root cause instantly and keep the system operational. Keeping the system operational is important to get hold of the debug information without special debugging aids like serial consoles and special knowledge of the bug reporter. The problems described above are not restricted to timers, but timers tend to expose it usually in a full system crash. Other objects are less explosive, but the symptoms caused by such mistakes can be even harder to debug. Instead of creating specialized debugging code for the timer subsystem a generic infrastructure is created which allows developers to verify their code and provides an easy to enable debug facility for users in case of trouble. The debugobjects core code keeps track of operations on static and dynamic objects by inserting them into a hashed list and sanity checking them on object operations and provides additional checks whenever kernel memory is freed. The tracked object operations are: - initializing an object - adding an object to a subsystem list - deleting an object from a subsystem list Each operation is sanity checked before the operation is executed and the subsystem specific code can provide a fixup function which allows to prevent the damage of the operation. When the sanity check triggers a warning message and a stack trace is printed. The list of operations can be extended if the need arises. For now it's limited to the requirements of the first user (timers). The core code enqueues the objects into hash buckets. The hash index is generated from the address of the object to simplify the lookup for the check on kfree/vfree. Each bucket has it's own spinlock to avoid contention on a global lock. The debug code can be compiled in without being active. The runtime overhead is minimal and could be optimized by asm alternatives. A kernel command line option enables the debugging code. Thanks to Ingo Molnar for review, suggestions and cleanup patches. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Greg KH <greg@kroah.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 15:55:01 +08:00
#include <linux/debugobjects.h>
vmallocinfo: add caller information Add caller information so that /proc/vmallocinfo shows where the allocation request for a slice of vmalloc memory originated. Results in output like this: 0xffffc20000000000-0xffffc20000801000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20000801000-0xffffc20000806000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000806000-0xffffc20000c07000 4198400 alloc_large_system_hash+0x127/0x246 pages=1024 vmalloc vpages 0xffffc20000c07000-0xffffc20000c0a000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c0a000-0xffffc20000c0c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c0c000-0xffffc20000c0f000 12288 acpi_os_map_memory+0x13/0x1c phys=cff64000 ioremap 0xffffc20000c10000-0xffffc20000c15000 20480 acpi_os_map_memory+0x13/0x1c phys=cff65000 ioremap 0xffffc20000c16000-0xffffc20000c18000 8192 acpi_os_map_memory+0x13/0x1c phys=cff69000 ioremap 0xffffc20000c18000-0xffffc20000c1a000 8192 acpi_os_map_memory+0x13/0x1c phys=fed1f000 ioremap 0xffffc20000c1a000-0xffffc20000c1c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1c000-0xffffc20000c1e000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1e000-0xffffc20000c20000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c20000-0xffffc20000c22000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c22000-0xffffc20000c24000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c24000-0xffffc20000c26000 8192 acpi_os_map_memory+0x13/0x1c phys=e0081000 ioremap 0xffffc20000c26000-0xffffc20000c28000 8192 acpi_os_map_memory+0x13/0x1c phys=e0080000 ioremap 0xffffc20000c28000-0xffffc20000c2d000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000c2d000-0xffffc20000c31000 16384 tcp_init+0xd5/0x31c pages=3 vmalloc 0xffffc20000c31000-0xffffc20000c34000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c34000-0xffffc20000c36000 8192 init_vdso_vars+0xde/0x1f1 0xffffc20000c36000-0xffffc20000c38000 8192 pci_iomap+0x8a/0xb4 phys=d8e00000 ioremap 0xffffc20000c38000-0xffffc20000c3a000 8192 usb_hcd_pci_probe+0x139/0x295 [usbcore] phys=d8e00000 ioremap 0xffffc20000c3a000-0xffffc20000c3e000 16384 sys_swapon+0x509/0xa15 pages=3 vmalloc 0xffffc20000c40000-0xffffc20000c61000 135168 e1000_probe+0x1c4/0xa32 phys=d8a20000 ioremap 0xffffc20000c61000-0xffffc20000c6a000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c6a000-0xffffc20000c73000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c73000-0xffffc20000c7c000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c7c000-0xffffc20000c7f000 12288 e1000e_setup_tx_resources+0x29/0xbe pages=2 vmalloc 0xffffc20000c80000-0xffffc20001481000 8392704 pci_mmcfg_arch_init+0x90/0x118 phys=e0000000 ioremap 0xffffc20001481000-0xffffc20001682000 2101248 alloc_large_system_hash+0x127/0x246 pages=512 vmalloc 0xffffc20001682000-0xffffc20001e83000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20001e83000-0xffffc20002204000 3674112 alloc_large_system_hash+0x127/0x246 pages=896 vmalloc vpages 0xffffc20002204000-0xffffc2000220d000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000220d000-0xffffc20002216000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002216000-0xffffc2000221f000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000221f000-0xffffc20002228000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002228000-0xffffc20002231000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002231000-0xffffc20002234000 12288 e1000e_setup_rx_resources+0x35/0x122 pages=2 vmalloc 0xffffc20002240000-0xffffc20002261000 135168 e1000_probe+0x1c4/0xa32 phys=d8a60000 ioremap 0xffffc20002261000-0xffffc2000270c000 4894720 sys_swapon+0x509/0xa15 pages=1194 vmalloc vpages 0xffffffffa0000000-0xffffffffa0022000 139264 module_alloc+0x4f/0x55 pages=33 vmalloc 0xffffffffa0022000-0xffffffffa0029000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc 0xffffffffa002b000-0xffffffffa0034000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa0034000-0xffffffffa003d000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa003d000-0xffffffffa0049000 49152 module_alloc+0x4f/0x55 pages=11 vmalloc 0xffffffffa0049000-0xffffffffa0050000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Lameter <clameter@sgi.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:12:42 +08:00
#include <linux/kallsyms.h>
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
#include <linux/list.h>
#include <linux/notifier.h>
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
#include <linux/rbtree.h>
#include <linux/xarray.h>
#include <linux/io.h>
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
#include <linux/rcupdate.h>
#include <linux/pfn.h>
#include <linux/kmemleak.h>
#include <linux/atomic.h>
#include <linux/compiler.h>
#include <linux/memcontrol.h>
#include <linux/llist.h>
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
#include <linux/uio.h>
mm: change __get_vm_area_node() to use fls_long() ioremap() and its related interfaces are used to create I/O mappings to memory-mapped I/O devices. The mapping sizes of the traditional I/O devices are relatively small. Non-volatile memory (NVM), however, has many GB and is going to have TB soon. It is not very efficient to create large I/O mappings with 4KB. This patchset extends the ioremap() interfaces to transparently create I/O mappings with huge pages whenever possible. ioremap() continues to use 4KB mappings when a huge page does not fit into a requested range. There is no change necessary to the drivers using ioremap(). A requested physical address must be aligned by a huge page size (1GB or 2MB on x86) for using huge page mapping, though. The kernel huge I/O mapping will improve performance of NVM and other devices with large memory, and reduce the time to create their mappings as well. On x86, MTRRs can override PAT memory types with a 4KB granularity. When using a huge page, MTRRs can override the memory type of the huge page, which may lead a performance penalty. The processor can also behave in an undefined manner if a huge page is mapped to a memory range that MTRRs have mapped with multiple different memory types. Therefore, the mapping code falls back to use a smaller page size toward 4KB when a mapping range is covered by non-WB type of MTRRs. The WB type of MTRRs has no affect on the PAT memory types. The patchset introduces HAVE_ARCH_HUGE_VMAP, which indicates that the arch supports huge KVA mappings for ioremap(). User may specify a new kernel option "nohugeiomap" to disable the huge I/O mapping capability of ioremap() when necessary. Patch 1-4 change common files to support huge I/O mappings. There is no change in the functinalities unless HAVE_ARCH_HUGE_VMAP is defined on the architecture of the system. Patch 5-6 implement the HAVE_ARCH_HUGE_VMAP funcs on x86, and set HAVE_ARCH_HUGE_VMAP on x86. This patch (of 6): __get_vm_area_node() takes unsigned long size, which is a 64-bit value on a 64-bit kernel. However, fls(size) simply ignores the upper 32-bit. Change to use fls_long() to handle the size properly. Signed-off-by: Toshi Kani <toshi.kani@hp.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Robert Elliott <Elliott@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-15 06:47:17 +08:00
#include <linux/bitops.h>
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
#include <linux/rbtree_augmented.h>
vmalloc: fix remap_vmalloc_range() bounds checks remap_vmalloc_range() has had various issues with the bounds checks it promises to perform ("This function checks that addr is a valid vmalloc'ed area, and that it is big enough to cover the vma") over time, e.g.: - not detecting pgoff<<PAGE_SHIFT overflow - not detecting (pgoff<<PAGE_SHIFT)+usize overflow - not checking whether addr and addr+(pgoff<<PAGE_SHIFT) are the same vmalloc allocation - comparing a potentially wildly out-of-bounds pointer with the end of the vmalloc region In particular, since commit fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"), unprivileged users can cause kernel null pointer dereferences by calling mmap() on a BPF map with a size that is bigger than the distance from the start of the BPF map to the end of the address space. This could theoretically be used as a kernel ASLR bypass, by using whether mmap() with a given offset oopses or returns an error code to perform a binary search over the possible address range. To allow remap_vmalloc_range_partial() to verify that addr and addr+(pgoff<<PAGE_SHIFT) are in the same vmalloc region, pass the offset to remap_vmalloc_range_partial() instead of adding it to the pointer in remap_vmalloc_range(). In remap_vmalloc_range_partial(), fix the check against get_vm_area_size() by using size comparisons instead of pointer comparisons, and add checks for pgoff. Fixes: 833423143c3a ("[PATCH] mm: introduce remap_vmalloc_range()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable@vger.kernel.org Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: Andrii Nakryiko <andriin@fb.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@chromium.org> Link: http://lkml.kernel.org/r/20200415222312.236431-1-jannh@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-21 09:14:11 +08:00
#include <linux/overflow.h>
mm/vmalloc: fix HUGE_VMAP regression by enabling huge pages in vmalloc_to_page vmalloc_to_page returns NULL for addresses mapped by larger pages[*]. Whether or not a vmap is huge depends on the architecture details, alignments, boot options, etc., which the caller can not be expected to know. Therefore HUGE_VMAP is a regression for vmalloc_to_page. This change teaches vmalloc_to_page about larger pages, and returns the struct page that corresponds to the offset within the large page. This makes the API agnostic to mapping implementation details. [*] As explained by commit 029c54b095995 ("mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings") [npiggin@gmail.com: sparc32: add stub pud_page define for walking huge vmalloc page tables] Link: https://lkml.kernel.org/r/20210324232825.1157363-1-npiggin@gmail.com Link: https://lkml.kernel.org/r/20210317062402.533919-3-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:13 +08:00
#include <linux/pgtable.h>
#include <linux/hugetlb.h>
mm/vmalloc: alloc GFP_NO{FS,IO} for vmalloc Patch series "extend vmalloc support for constrained allocations", v2. Based on a recent discussion with Dave and Neil [1] I have tried to implement NOFS, NOIO, NOFAIL support for the vmalloc to make life of kvmalloc users easier. A requirement for NOFAIL support for kvmalloc was new to me but this seems to be really needed by the xfs code. NOFS/NOIO was a known and a long term problem which was hoped to be handled by the scope API. Those scope should have been used at the reclaim recursion boundaries both to document them and also to remove the necessity of NOFS/NOIO constrains for all allocations within that scope. Instead workarounds were developed to wrap a single allocation instead (like ceph_kvmalloc). First patch implements NOFS/NOIO support for vmalloc. The second one adds NOFAIL support and the third one bundles all together into kvmalloc and drops ceph_kvmalloc which can use kvmalloc directly now. [1] http://lkml.kernel.org/r/163184741778.29351.16920832234899124642.stgit@noble.brown This patch (of 4): vmalloc historically hasn't supported GFP_NO{FS,IO} requests because page table allocations do not support externally provided gfp mask and performed GFP_KERNEL like allocations. Since few years we have scope (memalloc_no{fs,io}_{save,restore}) APIs to enforce NOFS and NOIO constrains implicitly to all allocators within the scope. There was a hope that those scopes would be defined on a higher level when the reclaim recursion boundary starts/stops (e.g. when a lock required during the memory reclaim is required etc.). It seems that not all NOFS/NOIO users have adopted this approach and instead they have taken a workaround approach to wrap a single [k]vmalloc allocation by a scope API. These workarounds do not serve the purpose of a better reclaim recursion documentation and reduction of explicit GFP_NO{FS,IO} usege so let's just provide them with the semantic they are asking for without a need for workarounds. Add support for GFP_NOFS and GFP_NOIO to vmalloc directly. All internal allocations already comply with the given gfp_mask. The only current exception is vmap_pages_range which maps kernel page tables. Infer the proper scope API based on the given gfp mask. [sfr@canb.auug.org.au: mm/vmalloc.c needs linux/sched/mm.h] Link: https://lkml.kernel.org/r/20211217232641.0148710c@canb.auug.org.au Link: https://lkml.kernel.org/r/20211122153233.9924-1-mhocko@kernel.org Link: https://lkml.kernel.org/r/20211122153233.9924-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Neil Brown <neilb@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Ilya Dryomov <idryomov@gmail.com> Cc: Jeff Layton <jlayton@kernel.org> Cc: Dave Chinner <dchinner@redhat.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-01-15 06:06:57 +08:00
#include <linux/sched/mm.h>
#include <asm/tlbflush.h>
#include <asm/shmparam.h>
#define CREATE_TRACE_POINTS
#include <trace/events/vmalloc.h>
#include "internal.h"
#include "pgalloc-track.h"
#ifdef CONFIG_HAVE_ARCH_HUGE_VMAP
static unsigned int __ro_after_init ioremap_max_page_shift = BITS_PER_LONG - 1;
static int __init set_nohugeiomap(char *str)
{
ioremap_max_page_shift = PAGE_SHIFT;
return 0;
}
early_param("nohugeiomap", set_nohugeiomap);
#else /* CONFIG_HAVE_ARCH_HUGE_VMAP */
static const unsigned int ioremap_max_page_shift = PAGE_SHIFT;
#endif /* CONFIG_HAVE_ARCH_HUGE_VMAP */
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
#ifdef CONFIG_HAVE_ARCH_HUGE_VMALLOC
static bool __ro_after_init vmap_allow_huge = true;
static int __init set_nohugevmalloc(char *str)
{
vmap_allow_huge = false;
return 0;
}
early_param("nohugevmalloc", set_nohugevmalloc);
#else /* CONFIG_HAVE_ARCH_HUGE_VMALLOC */
static const bool vmap_allow_huge = false;
#endif /* CONFIG_HAVE_ARCH_HUGE_VMALLOC */
bool is_vmalloc_addr(const void *x)
{
unsigned long addr = (unsigned long)kasan_reset_tag(x);
return addr >= VMALLOC_START && addr < VMALLOC_END;
}
EXPORT_SYMBOL(is_vmalloc_addr);
struct vfree_deferred {
struct llist_head list;
struct work_struct wq;
};
static DEFINE_PER_CPU(struct vfree_deferred, vfree_deferred);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*** Page table manipulation functions ***/
static int vmap_pte_range(pmd_t *pmd, unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot,
unsigned int max_page_shift, pgtbl_mod_mask *mask)
{
pte_t *pte;
u64 pfn;
unsigned long size = PAGE_SIZE;
pfn = phys_addr >> PAGE_SHIFT;
pte = pte_alloc_kernel_track(pmd, addr, mask);
if (!pte)
return -ENOMEM;
do {
mm: ptep_get() conversion Convert all instances of direct pte_t* dereferencing to instead use ptep_get() helper. This means that by default, the accesses change from a C dereference to a READ_ONCE(). This is technically the correct thing to do since where pgtables are modified by HW (for access/dirty) they are volatile and therefore we should always ensure READ_ONCE() semantics. But more importantly, by always using the helper, it can be overridden by the architecture to fully encapsulate the contents of the pte. Arch code is deliberately not converted, as the arch code knows best. It is intended that arch code (arm64) will override the default with its own implementation that can (e.g.) hide certain bits from the core code, or determine young/dirty status by mixing in state from another source. Conversion was done using Coccinelle: ---- // $ make coccicheck \ // COCCI=ptepget.cocci \ // SPFLAGS="--include-headers" \ // MODE=patch virtual patch @ depends on patch @ pte_t *v; @@ - *v + ptep_get(v) ---- Then reviewed and hand-edited to avoid multiple unnecessary calls to ptep_get(), instead opting to store the result of a single call in a variable, where it is correct to do so. This aims to negate any cost of READ_ONCE() and will benefit arch-overrides that may be more complex. Included is a fix for an issue in an earlier version of this patch that was pointed out by kernel test robot. The issue arose because config MMU=n elides definition of the ptep helper functions, including ptep_get(). HUGETLB_PAGE=n configs still define a simple huge_ptep_clear_flush() for linking purposes, which dereferences the ptep. So when both configs are disabled, this caused a build error because ptep_get() is not defined. Fix by continuing to do a direct dereference when MMU=n. This is safe because for this config the arch code cannot be trying to virtualize the ptes because none of the ptep helpers are defined. Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/ Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Christian Brauner <brauner@kernel.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: SeongJae Park <sj@kernel.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 23:15:45 +08:00
BUG_ON(!pte_none(ptep_get(pte)));
#ifdef CONFIG_HUGETLB_PAGE
size = arch_vmap_pte_range_map_size(addr, end, pfn, max_page_shift);
if (size != PAGE_SIZE) {
pte_t entry = pfn_pte(pfn, prot);
entry = arch_make_huge_pte(entry, ilog2(size), 0);
mm: hugetlb: add huge page size param to set_huge_pte_at() Patch series "Fix set_huge_pte_at() panic on arm64", v2. This series fixes a bug in arm64's implementation of set_huge_pte_at(), which can result in an unprivileged user causing a kernel panic. The problem was triggered when running the new uffd poison mm selftest for HUGETLB memory. This test (and the uffd poison feature) was merged for v6.5-rc7. Ideally, I'd like to get this fix in for v6.6 and I've cc'ed stable (correctly this time) to get it backported to v6.5, where the issue first showed up. Description of Bug ================== arm64's huge pte implementation supports multiple huge page sizes, some of which are implemented in the page table with multiple contiguous entries. So set_huge_pte_at() needs to work out how big the logical pte is, so that it can also work out how many physical ptes (or pmds) need to be written. It previously did this by grabbing the folio out of the pte and querying its size. However, there are cases when the pte being set is actually a swap entry. But this also used to work fine, because for huge ptes, we only ever saw migration entries and hwpoison entries. And both of these types of swap entries have a PFN embedded, so the code would grab that and everything still worked out. But over time, more calls to set_huge_pte_at() have been added that set swap entry types that do not embed a PFN. And this causes the code to go bang. The triggering case is for the uffd poison test, commit 99aa77215ad0 ("selftests/mm: add uffd unit test for UFFDIO_POISON"), which causes a PTE_MARKER_POISONED swap entry to be set, coutesey of commit 8a13897fb0da ("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs") - added in v6.5-rc7. Although review shows that there are other call sites that set PTE_MARKER_UFFD_WP (which also has no PFN), these don't trigger on arm64 because arm64 doesn't support UFFD WP. If CONFIG_DEBUG_VM is enabled, we do at least get a BUG(), but otherwise, it will dereference a bad pointer in page_folio(): static inline struct folio *hugetlb_swap_entry_to_folio(swp_entry_t entry) { VM_BUG_ON(!is_migration_entry(entry) && !is_hwpoison_entry(entry)); return page_folio(pfn_to_page(swp_offset_pfn(entry))); } Fix === The simplest fix would have been to revert the dodgy cleanup commit 18f3962953e4 ("mm: hugetlb: kill set_huge_swap_pte_at()"), but since things have moved on, this would have required an audit of all the new set_huge_pte_at() call sites to see if they should be converted to set_huge_swap_pte_at(). As per the original intent of the change, it would also leave us open to future bugs when people invariably get it wrong and call the wrong helper. So instead, I've added a huge page size parameter to set_huge_pte_at(). This means that the arm64 code has the size in all cases. It's a bigger change, due to needing to touch the arches that implement the function, but it is entirely mechanical, so in my view, low risk. I've compile-tested all touched arches; arm64, parisc, powerpc, riscv, s390, sparc (and additionally x86_64). I've additionally booted and run mm selftests against arm64, where I observe the uffd poison test is fixed, and there are no other regressions. This patch (of 2): In order to fix a bug, arm64 needs to be told the size of the huge page for which the pte is being set in set_huge_pte_at(). Provide for this by adding an `unsigned long sz` parameter to the function. This follows the same pattern as huge_pte_clear(). This commit makes the required interface modifications to the core mm as well as all arches that implement this function (arm64, parisc, powerpc, riscv, s390, sparc). The actual arm64 bug will be fixed in a separate commit. No behavioral changes intended. Link: https://lkml.kernel.org/r/20230922115804.2043771-1-ryan.roberts@arm.com Link: https://lkml.kernel.org/r/20230922115804.2043771-2-ryan.roberts@arm.com Fixes: 8a13897fb0da ("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs") Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> [powerpc 8xx] Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> [vmalloc change] Cc: Alexandre Ghiti <alex@ghiti.fr> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christian Borntraeger <borntraeger@linux.ibm.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: David S. Miller <davem@davemloft.net> Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Peter Xu <peterx@redhat.com> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Cc: <stable@vger.kernel.org> [6.5+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-09-22 19:58:03 +08:00
set_huge_pte_at(&init_mm, addr, pte, entry, size);
pfn += PFN_DOWN(size);
continue;
}
#endif
set_pte_at(&init_mm, addr, pte, pfn_pte(pfn, prot));
pfn++;
} while (pte += PFN_DOWN(size), addr += size, addr != end);
*mask |= PGTBL_PTE_MODIFIED;
return 0;
}
static int vmap_try_huge_pmd(pmd_t *pmd, unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot,
unsigned int max_page_shift)
{
if (max_page_shift < PMD_SHIFT)
return 0;
if (!arch_vmap_pmd_supported(prot))
return 0;
if ((end - addr) != PMD_SIZE)
return 0;
if (!IS_ALIGNED(addr, PMD_SIZE))
return 0;
if (!IS_ALIGNED(phys_addr, PMD_SIZE))
return 0;
if (pmd_present(*pmd) && !pmd_free_pte_page(pmd, addr))
return 0;
return pmd_set_huge(pmd, phys_addr, prot);
}
static int vmap_pmd_range(pud_t *pud, unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot,
unsigned int max_page_shift, pgtbl_mod_mask *mask)
{
pmd_t *pmd;
unsigned long next;
pmd = pmd_alloc_track(&init_mm, pud, addr, mask);
if (!pmd)
return -ENOMEM;
do {
next = pmd_addr_end(addr, end);
if (vmap_try_huge_pmd(pmd, addr, next, phys_addr, prot,
max_page_shift)) {
*mask |= PGTBL_PMD_MODIFIED;
continue;
}
if (vmap_pte_range(pmd, addr, next, phys_addr, prot, max_page_shift, mask))
return -ENOMEM;
} while (pmd++, phys_addr += (next - addr), addr = next, addr != end);
return 0;
}
static int vmap_try_huge_pud(pud_t *pud, unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot,
unsigned int max_page_shift)
{
if (max_page_shift < PUD_SHIFT)
return 0;
if (!arch_vmap_pud_supported(prot))
return 0;
if ((end - addr) != PUD_SIZE)
return 0;
if (!IS_ALIGNED(addr, PUD_SIZE))
return 0;
if (!IS_ALIGNED(phys_addr, PUD_SIZE))
return 0;
if (pud_present(*pud) && !pud_free_pmd_page(pud, addr))
return 0;
return pud_set_huge(pud, phys_addr, prot);
}
static int vmap_pud_range(p4d_t *p4d, unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot,
unsigned int max_page_shift, pgtbl_mod_mask *mask)
{
pud_t *pud;
unsigned long next;
pud = pud_alloc_track(&init_mm, p4d, addr, mask);
if (!pud)
return -ENOMEM;
do {
next = pud_addr_end(addr, end);
if (vmap_try_huge_pud(pud, addr, next, phys_addr, prot,
max_page_shift)) {
*mask |= PGTBL_PUD_MODIFIED;
continue;
}
if (vmap_pmd_range(pud, addr, next, phys_addr, prot,
max_page_shift, mask))
return -ENOMEM;
} while (pud++, phys_addr += (next - addr), addr = next, addr != end);
return 0;
}
static int vmap_try_huge_p4d(p4d_t *p4d, unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot,
unsigned int max_page_shift)
{
if (max_page_shift < P4D_SHIFT)
return 0;
if (!arch_vmap_p4d_supported(prot))
return 0;
if ((end - addr) != P4D_SIZE)
return 0;
if (!IS_ALIGNED(addr, P4D_SIZE))
return 0;
if (!IS_ALIGNED(phys_addr, P4D_SIZE))
return 0;
if (p4d_present(*p4d) && !p4d_free_pud_page(p4d, addr))
return 0;
return p4d_set_huge(p4d, phys_addr, prot);
}
static int vmap_p4d_range(pgd_t *pgd, unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot,
unsigned int max_page_shift, pgtbl_mod_mask *mask)
{
p4d_t *p4d;
unsigned long next;
p4d = p4d_alloc_track(&init_mm, pgd, addr, mask);
if (!p4d)
return -ENOMEM;
do {
next = p4d_addr_end(addr, end);
if (vmap_try_huge_p4d(p4d, addr, next, phys_addr, prot,
max_page_shift)) {
*mask |= PGTBL_P4D_MODIFIED;
continue;
}
if (vmap_pud_range(p4d, addr, next, phys_addr, prot,
max_page_shift, mask))
return -ENOMEM;
} while (p4d++, phys_addr += (next - addr), addr = next, addr != end);
return 0;
}
static int vmap_range_noflush(unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot,
unsigned int max_page_shift)
{
pgd_t *pgd;
unsigned long start;
unsigned long next;
int err;
pgtbl_mod_mask mask = 0;
might_sleep();
BUG_ON(addr >= end);
start = addr;
pgd = pgd_offset_k(addr);
do {
next = pgd_addr_end(addr, end);
err = vmap_p4d_range(pgd, addr, next, phys_addr, prot,
max_page_shift, &mask);
if (err)
break;
} while (pgd++, phys_addr += (next - addr), addr = next, addr != end);
if (mask & ARCH_PAGE_TABLE_SYNC_MASK)
arch_sync_kernel_mappings(start, end);
return err;
}
int vmap_page_range(unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot)
{
int err;
err = vmap_range_noflush(addr, end, phys_addr, pgprot_nx(prot),
ioremap_max_page_shift);
flush_cache_vmap(addr, end);
if (!err)
err = kmsan_ioremap_page_range(addr, end, phys_addr, prot,
ioremap_max_page_shift);
return err;
}
int ioremap_page_range(unsigned long addr, unsigned long end,
phys_addr_t phys_addr, pgprot_t prot)
{
struct vm_struct *area;
area = find_vm_area((void *)addr);
if (!area || !(area->flags & VM_IOREMAP)) {
WARN_ONCE(1, "vm_area at addr %lx is not marked as VM_IOREMAP\n", addr);
return -EINVAL;
}
if (addr != (unsigned long)area->addr ||
(void *)end != area->addr + get_vm_area_size(area)) {
WARN_ONCE(1, "ioremap request [%lx,%lx) doesn't match vm_area [%lx, %lx)\n",
addr, end, (long)area->addr,
(long)area->addr + get_vm_area_size(area));
return -ERANGE;
}
return vmap_page_range(addr, end, phys_addr, prot);
}
static void vunmap_pte_range(pmd_t *pmd, unsigned long addr, unsigned long end,
pgtbl_mod_mask *mask)
{
pte_t *pte;
pte = pte_offset_kernel(pmd, addr);
do {
pte_t ptent = ptep_get_and_clear(&init_mm, addr, pte);
WARN_ON(!pte_none(ptent) && !pte_present(ptent));
} while (pte++, addr += PAGE_SIZE, addr != end);
*mask |= PGTBL_PTE_MODIFIED;
}
static void vunmap_pmd_range(pud_t *pud, unsigned long addr, unsigned long end,
pgtbl_mod_mask *mask)
{
pmd_t *pmd;
unsigned long next;
int cleared;
pmd = pmd_offset(pud, addr);
do {
next = pmd_addr_end(addr, end);
cleared = pmd_clear_huge(pmd);
if (cleared || pmd_bad(*pmd))
*mask |= PGTBL_PMD_MODIFIED;
if (cleared)
continue;
if (pmd_none_or_clear_bad(pmd))
continue;
vunmap_pte_range(pmd, addr, next, mask);
cond_resched();
} while (pmd++, addr = next, addr != end);
}
static void vunmap_pud_range(p4d_t *p4d, unsigned long addr, unsigned long end,
pgtbl_mod_mask *mask)
{
pud_t *pud;
unsigned long next;
int cleared;
pud = pud_offset(p4d, addr);
do {
next = pud_addr_end(addr, end);
cleared = pud_clear_huge(pud);
if (cleared || pud_bad(*pud))
*mask |= PGTBL_PUD_MODIFIED;
if (cleared)
continue;
if (pud_none_or_clear_bad(pud))
continue;
vunmap_pmd_range(pud, addr, next, mask);
} while (pud++, addr = next, addr != end);
}
static void vunmap_p4d_range(pgd_t *pgd, unsigned long addr, unsigned long end,
pgtbl_mod_mask *mask)
{
p4d_t *p4d;
unsigned long next;
p4d = p4d_offset(pgd, addr);
do {
next = p4d_addr_end(addr, end);
p4d_clear_huge(p4d);
if (p4d_bad(*p4d))
*mask |= PGTBL_P4D_MODIFIED;
if (p4d_none_or_clear_bad(p4d))
continue;
vunmap_pud_range(p4d, addr, next, mask);
} while (p4d++, addr = next, addr != end);
}
/*
* vunmap_range_noflush is similar to vunmap_range, but does not
* flush caches or TLBs.
mm: remove vmap_page_range_noflush and vunmap_page_range These have non-static aliases called map_kernel_range_noflush and unmap_kernel_range_noflush that just differ slightly in the calling conventions that pass addr + size instead of an end. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-14-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:07 +08:00
*
* The caller is responsible for calling flush_cache_vmap() before calling
* this function, and flush_tlb_kernel_range after it has returned
* successfully (and before the addresses are expected to cause a page fault
* or be re-mapped for something else, if TLB flushes are being delayed or
* coalesced).
mm: remove vmap_page_range_noflush and vunmap_page_range These have non-static aliases called map_kernel_range_noflush and unmap_kernel_range_noflush that just differ slightly in the calling conventions that pass addr + size instead of an end. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-14-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:07 +08:00
*
* This is an internal function only. Do not use outside mm/.
mm: remove vmap_page_range_noflush and vunmap_page_range These have non-static aliases called map_kernel_range_noflush and unmap_kernel_range_noflush that just differ slightly in the calling conventions that pass addr + size instead of an end. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-14-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:07 +08:00
*/
mm: kmsan: maintain KMSAN metadata for page operations Insert KMSAN hooks that make the necessary bookkeeping changes: - poison page shadow and origins in alloc_pages()/free_page(); - clear page shadow and origins in clear_page(), copy_user_highpage(); - copy page metadata in copy_highpage(), wp_page_copy(); - handle vmap()/vunmap()/iounmap(); Link: https://lkml.kernel.org/r/20220915150417.722975-15-glider@google.com Signed-off-by: Alexander Potapenko <glider@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Ilya Leoshkevich <iii@linux.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vegard Nossum <vegard.nossum@oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-15 23:03:48 +08:00
void __vunmap_range_noflush(unsigned long start, unsigned long end)
{
unsigned long next;
mm: remove vmap_page_range_noflush and vunmap_page_range These have non-static aliases called map_kernel_range_noflush and unmap_kernel_range_noflush that just differ slightly in the calling conventions that pass addr + size instead of an end. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-14-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:07 +08:00
pgd_t *pgd;
unsigned long addr = start;
pgtbl_mod_mask mask = 0;
BUG_ON(addr >= end);
pgd = pgd_offset_k(addr);
do {
next = pgd_addr_end(addr, end);
if (pgd_bad(*pgd))
mask |= PGTBL_PGD_MODIFIED;
if (pgd_none_or_clear_bad(pgd))
continue;
vunmap_p4d_range(pgd, addr, next, &mask);
} while (pgd++, addr = next, addr != end);
if (mask & ARCH_PAGE_TABLE_SYNC_MASK)
arch_sync_kernel_mappings(start, end);
}
mm: kmsan: maintain KMSAN metadata for page operations Insert KMSAN hooks that make the necessary bookkeeping changes: - poison page shadow and origins in alloc_pages()/free_page(); - clear page shadow and origins in clear_page(), copy_user_highpage(); - copy page metadata in copy_highpage(), wp_page_copy(); - handle vmap()/vunmap()/iounmap(); Link: https://lkml.kernel.org/r/20220915150417.722975-15-glider@google.com Signed-off-by: Alexander Potapenko <glider@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Ilya Leoshkevich <iii@linux.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vegard Nossum <vegard.nossum@oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-15 23:03:48 +08:00
void vunmap_range_noflush(unsigned long start, unsigned long end)
{
kmsan_vunmap_range_noflush(start, end);
__vunmap_range_noflush(start, end);
}
/**
* vunmap_range - unmap kernel virtual addresses
* @addr: start of the VM area to unmap
* @end: end of the VM area to unmap (non-inclusive)
*
* Clears any present PTEs in the virtual address range, flushes TLBs and
* caches. Any subsequent access to the address before it has been re-mapped
* is a kernel bug.
*/
void vunmap_range(unsigned long addr, unsigned long end)
{
flush_cache_vunmap(addr, end);
vunmap_range_noflush(addr, end);
flush_tlb_kernel_range(addr, end);
}
static int vmap_pages_pte_range(pmd_t *pmd, unsigned long addr,
unsigned long end, pgprot_t prot, struct page **pages, int *nr,
pgtbl_mod_mask *mask)
{
pte_t *pte;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*
* nr is a running index into the array which helps higher level
* callers keep track of where we're up to.
*/
pte = pte_alloc_kernel_track(pmd, addr, mask);
if (!pte)
return -ENOMEM;
do {
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
struct page *page = pages[*nr];
mm: ptep_get() conversion Convert all instances of direct pte_t* dereferencing to instead use ptep_get() helper. This means that by default, the accesses change from a C dereference to a READ_ONCE(). This is technically the correct thing to do since where pgtables are modified by HW (for access/dirty) they are volatile and therefore we should always ensure READ_ONCE() semantics. But more importantly, by always using the helper, it can be overridden by the architecture to fully encapsulate the contents of the pte. Arch code is deliberately not converted, as the arch code knows best. It is intended that arch code (arm64) will override the default with its own implementation that can (e.g.) hide certain bits from the core code, or determine young/dirty status by mixing in state from another source. Conversion was done using Coccinelle: ---- // $ make coccicheck \ // COCCI=ptepget.cocci \ // SPFLAGS="--include-headers" \ // MODE=patch virtual patch @ depends on patch @ pte_t *v; @@ - *v + ptep_get(v) ---- Then reviewed and hand-edited to avoid multiple unnecessary calls to ptep_get(), instead opting to store the result of a single call in a variable, where it is correct to do so. This aims to negate any cost of READ_ONCE() and will benefit arch-overrides that may be more complex. Included is a fix for an issue in an earlier version of this patch that was pointed out by kernel test robot. The issue arose because config MMU=n elides definition of the ptep helper functions, including ptep_get(). HUGETLB_PAGE=n configs still define a simple huge_ptep_clear_flush() for linking purposes, which dereferences the ptep. So when both configs are disabled, this caused a build error because ptep_get() is not defined. Fix by continuing to do a direct dereference when MMU=n. This is safe because for this config the arch code cannot be trying to virtualize the ptes because none of the ptep helpers are defined. Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/ Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Christian Brauner <brauner@kernel.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: SeongJae Park <sj@kernel.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 23:15:45 +08:00
if (WARN_ON(!pte_none(ptep_get(pte))))
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
return -EBUSY;
if (WARN_ON(!page))
return -ENOMEM;
vmap(): don't allow invalid pages vmap() takes struct page *pages as one of arguments, and user may provide an invalid pointer which may lead to corrupted translation table. An example of such behaviour is erroneous usage of virt_to_page(): vaddr1 = dma_alloc_coherent() page = virt_to_page() // Wrong here ... vaddr2 = vmap(page) memset(vaddr2) // Faulting here virt_to_page() returns a wrong pointer if vaddr1 is not a linear kernel address. The problem is that vmap() populates pte with bad pfn successfully, and it's much harder to debug at memory access time. This case should be caught by DEBUG_VIRTUAL being that enabled, but it's not enabled in popular distros. Kernel already checks the pages against NULL. In the case mentioned above, however, the address is not NULL, and it's big enough so that the hardware generated Address Size Abort on arm64: [ 665.484101] Unhandled fault at 0xffff8000252cd000 [ 665.488807] Mem abort info: [ 665.491617] ESR = 0x96000043 [ 665.494675] EC = 0x25: DABT (current EL), IL = 32 bits [ 665.499985] SET = 0, FnV = 0 [ 665.503039] EA = 0, S1PTW = 0 [ 665.506167] Data abort info: [ 665.509047] ISV = 0, ISS = 0x00000043 [ 665.512882] CM = 0, WnR = 1 [ 665.515851] swapper pgtable: 4k pages, 48-bit VAs, pgdp=00000000818cb000 [ 665.522550] [ffff8000252cd000] pgd=000000affcfff003, pud=000000affcffe003, pmd=0000008fad8c3003, pte=00688000a5217713 [ 665.533160] Internal error: level 3 address size fault: 96000043 [#1] SMP [ 665.539936] Modules linked in: [...] [ 665.616212] CPU: 178 PID: 13199 Comm: test Tainted: P OE 5.4.0-84-generic #94~18.04.1-Ubuntu [ 665.626806] Hardware name: HPE Apollo 70 /C01_APACHE_MB , BIOS L50_5.13_1.0.6 07/10/2018 [ 665.636618] pstate: 80400009 (Nzcv daif +PAN -UAO) [ 665.641407] pc : __memset+0x38/0x188 [ 665.645146] lr : test+0xcc/0x3f8 [ 665.650184] sp : ffff8000359bb840 [ 665.653486] x29: ffff8000359bb840 x28: 0000000000000000 [ 665.658785] x27: 0000000000000000 x26: 0000000000231000 [ 665.664083] x25: ffff00ae660f6110 x24: ffff00ae668cb800 [ 665.669382] x23: 0000000000000001 x22: ffff00af533e5000 [ 665.674680] x21: 0000000000001000 x20: 0000000000000000 [ 665.679978] x19: ffff00ae66950000 x18: ffffffffffffffff [ 665.685276] x17: 00000000588636a5 x16: 0000000000000013 [ 665.690574] x15: ffffffffffffffff x14: 000000000007ffff [ 665.695872] x13: 0000000080000000 x12: 0140000000000000 [ 665.701170] x11: 0000000000000041 x10: ffff8000652cd000 [ 665.706468] x9 : ffff8000252cf000 x8 : ffff8000252cd000 [ 665.711767] x7 : 0303030303030303 x6 : 0000000000001000 [ 665.717065] x5 : ffff8000252cd000 x4 : 0000000000000000 [ 665.722363] x3 : ffff8000252cdfff x2 : 0000000000000001 [ 665.727661] x1 : 0000000000000003 x0 : ffff8000252cd000 [ 665.732960] Call trace: [ 665.735395] __memset+0x38/0x188 [...] Interestingly, this abort happens even if copy_from_kernel_nofault() is used, which is quite inconvenient for debugging purposes. This patch adds a pfn_valid() check into vmap() path, so that invalid mapping will not be created; WARN_ON() is used to let client code know that something goes wrong, and it's not a regular EINVAL situation. Link: https://lkml.kernel.org/r/20220422220410.1308706-1-yury.norov@gmail.com Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com> Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Alexey Klimov <aklimov@redhat.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-04-29 14:16:00 +08:00
if (WARN_ON(!pfn_valid(page_to_pfn(page))))
return -EINVAL;
set_pte_at(&init_mm, addr, pte, mk_pte(page, prot));
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
(*nr)++;
} while (pte++, addr += PAGE_SIZE, addr != end);
*mask |= PGTBL_PTE_MODIFIED;
return 0;
}
static int vmap_pages_pmd_range(pud_t *pud, unsigned long addr,
unsigned long end, pgprot_t prot, struct page **pages, int *nr,
pgtbl_mod_mask *mask)
{
pmd_t *pmd;
unsigned long next;
pmd = pmd_alloc_track(&init_mm, pud, addr, mask);
if (!pmd)
return -ENOMEM;
do {
next = pmd_addr_end(addr, end);
if (vmap_pages_pte_range(pmd, addr, next, prot, pages, nr, mask))
return -ENOMEM;
} while (pmd++, addr = next, addr != end);
return 0;
}
static int vmap_pages_pud_range(p4d_t *p4d, unsigned long addr,
unsigned long end, pgprot_t prot, struct page **pages, int *nr,
pgtbl_mod_mask *mask)
{
pud_t *pud;
unsigned long next;
pud = pud_alloc_track(&init_mm, p4d, addr, mask);
if (!pud)
return -ENOMEM;
do {
next = pud_addr_end(addr, end);
if (vmap_pages_pmd_range(pud, addr, next, prot, pages, nr, mask))
return -ENOMEM;
} while (pud++, addr = next, addr != end);
return 0;
}
static int vmap_pages_p4d_range(pgd_t *pgd, unsigned long addr,
unsigned long end, pgprot_t prot, struct page **pages, int *nr,
pgtbl_mod_mask *mask)
{
p4d_t *p4d;
unsigned long next;
p4d = p4d_alloc_track(&init_mm, pgd, addr, mask);
if (!p4d)
return -ENOMEM;
do {
next = p4d_addr_end(addr, end);
if (vmap_pages_pud_range(p4d, addr, next, prot, pages, nr, mask))
return -ENOMEM;
} while (p4d++, addr = next, addr != end);
return 0;
}
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
static int vmap_small_pages_range_noflush(unsigned long addr, unsigned long end,
pgprot_t prot, struct page **pages)
{
unsigned long start = addr;
mm: remove vmap_page_range_noflush and vunmap_page_range These have non-static aliases called map_kernel_range_noflush and unmap_kernel_range_noflush that just differ slightly in the calling conventions that pass addr + size instead of an end. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-14-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:07 +08:00
pgd_t *pgd;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
unsigned long next;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
int err = 0;
int nr = 0;
pgtbl_mod_mask mask = 0;
BUG_ON(addr >= end);
pgd = pgd_offset_k(addr);
do {
next = pgd_addr_end(addr, end);
if (pgd_bad(*pgd))
mask |= PGTBL_PGD_MODIFIED;
err = vmap_pages_p4d_range(pgd, addr, next, prot, pages, &nr, &mask);
if (err)
return err;
} while (pgd++, addr = next, addr != end);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (mask & ARCH_PAGE_TABLE_SYNC_MASK)
arch_sync_kernel_mappings(start, end);
mm: don't return the number of pages from map_kernel_range{,_noflush} None of the callers needs the number of pages, and a 0 / -errno return value is a lot more intuitive. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-16-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:15 +08:00
return 0;
}
/*
* vmap_pages_range_noflush is similar to vmap_pages_range, but does not
* flush caches.
*
* The caller is responsible for calling flush_cache_vmap() after this
* function returns successfully and before the addresses are accessed.
*
* This is an internal function only. Do not use outside mm/.
*/
mm: kmsan: maintain KMSAN metadata for page operations Insert KMSAN hooks that make the necessary bookkeeping changes: - poison page shadow and origins in alloc_pages()/free_page(); - clear page shadow and origins in clear_page(), copy_user_highpage(); - copy page metadata in copy_highpage(), wp_page_copy(); - handle vmap()/vunmap()/iounmap(); Link: https://lkml.kernel.org/r/20220915150417.722975-15-glider@google.com Signed-off-by: Alexander Potapenko <glider@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Ilya Leoshkevich <iii@linux.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vegard Nossum <vegard.nossum@oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-15 23:03:48 +08:00
int __vmap_pages_range_noflush(unsigned long addr, unsigned long end,
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
pgprot_t prot, struct page **pages, unsigned int page_shift)
{
unsigned int i, nr = (end - addr) >> PAGE_SHIFT;
WARN_ON(page_shift < PAGE_SHIFT);
if (!IS_ENABLED(CONFIG_HAVE_ARCH_HUGE_VMALLOC) ||
page_shift == PAGE_SHIFT)
return vmap_small_pages_range_noflush(addr, end, prot, pages);
for (i = 0; i < nr; i += 1U << (page_shift - PAGE_SHIFT)) {
int err;
err = vmap_range_noflush(addr, addr + (1UL << page_shift),
page_to_phys(pages[i]), prot,
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
page_shift);
if (err)
return err;
addr += 1UL << page_shift;
}
return 0;
}
mm: kmsan: maintain KMSAN metadata for page operations Insert KMSAN hooks that make the necessary bookkeeping changes: - poison page shadow and origins in alloc_pages()/free_page(); - clear page shadow and origins in clear_page(), copy_user_highpage(); - copy page metadata in copy_highpage(), wp_page_copy(); - handle vmap()/vunmap()/iounmap(); Link: https://lkml.kernel.org/r/20220915150417.722975-15-glider@google.com Signed-off-by: Alexander Potapenko <glider@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Ilya Leoshkevich <iii@linux.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vegard Nossum <vegard.nossum@oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-15 23:03:48 +08:00
int vmap_pages_range_noflush(unsigned long addr, unsigned long end,
pgprot_t prot, struct page **pages, unsigned int page_shift)
{
int ret = kmsan_vmap_pages_range_noflush(addr, end, prot, pages,
page_shift);
if (ret)
return ret;
mm: kmsan: maintain KMSAN metadata for page operations Insert KMSAN hooks that make the necessary bookkeeping changes: - poison page shadow and origins in alloc_pages()/free_page(); - clear page shadow and origins in clear_page(), copy_user_highpage(); - copy page metadata in copy_highpage(), wp_page_copy(); - handle vmap()/vunmap()/iounmap(); Link: https://lkml.kernel.org/r/20220915150417.722975-15-glider@google.com Signed-off-by: Alexander Potapenko <glider@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Ilya Leoshkevich <iii@linux.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vegard Nossum <vegard.nossum@oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-15 23:03:48 +08:00
return __vmap_pages_range_noflush(addr, end, prot, pages, page_shift);
}
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
/**
* vmap_pages_range - map pages to a kernel virtual address
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
* @addr: start of the VM area to map
* @end: end of the VM area to map (non-inclusive)
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
* @prot: page protection flags to use
* @pages: pages to map (always PAGE_SIZE pages)
* @page_shift: maximum shift that the pages may be mapped with, @pages must
* be aligned and contiguous up to at least this shift.
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
*
* RETURNS:
* 0 on success, -errno on failure.
*/
static int vmap_pages_range(unsigned long addr, unsigned long end,
pgprot_t prot, struct page **pages, unsigned int page_shift)
{
int err;
err = vmap_pages_range_noflush(addr, end, prot, pages, page_shift);
flush_cache_vmap(addr, end);
return err;
}
mm: Introduce VM_SPARSE kind and vm_area_[un]map_pages(). vmap/vmalloc APIs are used to map a set of pages into contiguous kernel virtual space. get_vm_area() with appropriate flag is used to request an area of kernel address range. It's used for vmalloc, vmap, ioremap, xen use cases. - vmalloc use case dominates the usage. Such vm areas have VM_ALLOC flag. - the areas created by vmap() function should be tagged with VM_MAP. - ioremap areas are tagged with VM_IOREMAP. BPF would like to extend the vmap API to implement a lazily-populated sparse, yet contiguous kernel virtual space. Introduce VM_SPARSE flag and vm_area_map_pages(area, start_addr, count, pages) API to map a set of pages within a given area. It has the same sanity checks as vmap() does. It also checks that get_vm_area() was created with VM_SPARSE flag which identifies such areas in /proc/vmallocinfo and returns zero pages on read through /proc/kcore. The next commits will introduce bpf_arena which is a sparsely populated shared memory region between bpf program and user space process. It will map privately-managed pages into a sparse vm area with the following steps: // request virtual memory region during bpf prog verification area = get_vm_area(area_size, VM_SPARSE); // on demand vm_area_map_pages(area, kaddr, kend, pages); vm_area_unmap_pages(area, kaddr, kend); // after bpf program is detached and unloaded free_vm_area(area); Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com> Link: https://lore.kernel.org/bpf/20240305030516.41519-3-alexei.starovoitov@gmail.com
2024-03-05 11:05:16 +08:00
static int check_sparse_vm_area(struct vm_struct *area, unsigned long start,
unsigned long end)
{
might_sleep();
if (WARN_ON_ONCE(area->flags & VM_FLUSH_RESET_PERMS))
return -EINVAL;
if (WARN_ON_ONCE(area->flags & VM_NO_GUARD))
return -EINVAL;
if (WARN_ON_ONCE(!(area->flags & VM_SPARSE)))
return -EINVAL;
if ((end - start) >> PAGE_SHIFT > totalram_pages())
return -E2BIG;
if (start < (unsigned long)area->addr ||
(void *)end > area->addr + get_vm_area_size(area))
return -ERANGE;
return 0;
}
/**
* vm_area_map_pages - map pages inside given sparse vm_area
* @area: vm_area
* @start: start address inside vm_area
* @end: end address inside vm_area
* @pages: pages to map (always PAGE_SIZE pages)
*/
int vm_area_map_pages(struct vm_struct *area, unsigned long start,
unsigned long end, struct page **pages)
{
int err;
err = check_sparse_vm_area(area, start, end);
if (err)
return err;
return vmap_pages_range(start, end, PAGE_KERNEL, pages, PAGE_SHIFT);
}
/**
* vm_area_unmap_pages - unmap pages inside given sparse vm_area
* @area: vm_area
* @start: start address inside vm_area
* @end: end address inside vm_area
*/
void vm_area_unmap_pages(struct vm_struct *area, unsigned long start,
unsigned long end)
{
if (check_sparse_vm_area(area, start, end))
return;
vunmap_range(start, end);
}
int is_vmalloc_or_module_addr(const void *x)
{
/*
* ARM, x86-64 and sparc64 put modules in a special place,
* and fall back on vmalloc() if that fails. Others
* just put it in the vmalloc space.
*/
#if defined(CONFIG_MODULES) && defined(MODULES_VADDR)
unsigned long addr = (unsigned long)kasan_reset_tag(x);
if (addr >= MODULES_VADDR && addr < MODULES_END)
return 1;
#endif
return is_vmalloc_addr(x);
}
EXPORT_SYMBOL_GPL(is_vmalloc_or_module_addr);
/*
mm/vmalloc: fix HUGE_VMAP regression by enabling huge pages in vmalloc_to_page vmalloc_to_page returns NULL for addresses mapped by larger pages[*]. Whether or not a vmap is huge depends on the architecture details, alignments, boot options, etc., which the caller can not be expected to know. Therefore HUGE_VMAP is a regression for vmalloc_to_page. This change teaches vmalloc_to_page about larger pages, and returns the struct page that corresponds to the offset within the large page. This makes the API agnostic to mapping implementation details. [*] As explained by commit 029c54b095995 ("mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings") [npiggin@gmail.com: sparc32: add stub pud_page define for walking huge vmalloc page tables] Link: https://lkml.kernel.org/r/20210324232825.1157363-1-npiggin@gmail.com Link: https://lkml.kernel.org/r/20210317062402.533919-3-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:13 +08:00
* Walk a vmap address to the struct page it maps. Huge vmap mappings will
* return the tail page that corresponds to the base page address, which
* matches small vmap mappings.
*/
struct page *vmalloc_to_page(const void *vmalloc_addr)
{
unsigned long addr = (unsigned long) vmalloc_addr;
struct page *page = NULL;
pgd_t *pgd = pgd_offset_k(addr);
p4d_t *p4d;
pud_t *pud;
pmd_t *pmd;
pte_t *ptep, pte;
/*
* XXX we might need to change this if we add VIRTUAL_BUG_ON for
* architectures that do not vmalloc module space
*/
VIRTUAL_BUG_ON(!is_vmalloc_or_module_addr(vmalloc_addr));
if (pgd_none(*pgd))
return NULL;
mm/vmalloc: fix HUGE_VMAP regression by enabling huge pages in vmalloc_to_page vmalloc_to_page returns NULL for addresses mapped by larger pages[*]. Whether or not a vmap is huge depends on the architecture details, alignments, boot options, etc., which the caller can not be expected to know. Therefore HUGE_VMAP is a regression for vmalloc_to_page. This change teaches vmalloc_to_page about larger pages, and returns the struct page that corresponds to the offset within the large page. This makes the API agnostic to mapping implementation details. [*] As explained by commit 029c54b095995 ("mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings") [npiggin@gmail.com: sparc32: add stub pud_page define for walking huge vmalloc page tables] Link: https://lkml.kernel.org/r/20210324232825.1157363-1-npiggin@gmail.com Link: https://lkml.kernel.org/r/20210317062402.533919-3-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:13 +08:00
if (WARN_ON_ONCE(pgd_leaf(*pgd)))
return NULL; /* XXX: no allowance for huge pgd */
if (WARN_ON_ONCE(pgd_bad(*pgd)))
return NULL;
p4d = p4d_offset(pgd, addr);
if (p4d_none(*p4d))
return NULL;
mm/vmalloc: fix HUGE_VMAP regression by enabling huge pages in vmalloc_to_page vmalloc_to_page returns NULL for addresses mapped by larger pages[*]. Whether or not a vmap is huge depends on the architecture details, alignments, boot options, etc., which the caller can not be expected to know. Therefore HUGE_VMAP is a regression for vmalloc_to_page. This change teaches vmalloc_to_page about larger pages, and returns the struct page that corresponds to the offset within the large page. This makes the API agnostic to mapping implementation details. [*] As explained by commit 029c54b095995 ("mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings") [npiggin@gmail.com: sparc32: add stub pud_page define for walking huge vmalloc page tables] Link: https://lkml.kernel.org/r/20210324232825.1157363-1-npiggin@gmail.com Link: https://lkml.kernel.org/r/20210317062402.533919-3-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:13 +08:00
if (p4d_leaf(*p4d))
return p4d_page(*p4d) + ((addr & ~P4D_MASK) >> PAGE_SHIFT);
if (WARN_ON_ONCE(p4d_bad(*p4d)))
return NULL;
mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings Existing code that uses vmalloc_to_page() may assume that any address for which is_vmalloc_addr() returns true may be passed into vmalloc_to_page() to retrieve the associated struct page. This is not un unreasonable assumption to make, but on architectures that have CONFIG_HAVE_ARCH_HUGE_VMAP=y, it no longer holds, and we need to ensure that vmalloc_to_page() does not go off into the weeds trying to dereference huge PUDs or PMDs as table entries. Given that vmalloc() and vmap() themselves never create huge mappings or deal with compound pages at all, there is no correct answer in this case, so return NULL instead, and issue a warning. When reading /proc/kcore on arm64, you will hit an oops as soon as you hit the huge mappings used for the various segments that make up the mapping of vmlinux. With this patch applied, you will no longer hit the oops, but the kcore contents willl be incorrect (these regions will be zeroed out) We are fixing this for kcore specifically, so it avoids vread() for those regions. At least one other problematic user exists, i.e., /dev/kmem, but that is currently broken on arm64 for other reasons. Link: http://lkml.kernel.org/r/20170609082226.26152-1-ard.biesheuvel@linaro.org Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Laura Abbott <labbott@redhat.com> Cc: Michal Hocko <mhocko@suse.com> Cc: zhong jiang <zhongjiang@huawei.com> Cc: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-06-24 06:08:41 +08:00
mm/vmalloc: fix HUGE_VMAP regression by enabling huge pages in vmalloc_to_page vmalloc_to_page returns NULL for addresses mapped by larger pages[*]. Whether or not a vmap is huge depends on the architecture details, alignments, boot options, etc., which the caller can not be expected to know. Therefore HUGE_VMAP is a regression for vmalloc_to_page. This change teaches vmalloc_to_page about larger pages, and returns the struct page that corresponds to the offset within the large page. This makes the API agnostic to mapping implementation details. [*] As explained by commit 029c54b095995 ("mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings") [npiggin@gmail.com: sparc32: add stub pud_page define for walking huge vmalloc page tables] Link: https://lkml.kernel.org/r/20210324232825.1157363-1-npiggin@gmail.com Link: https://lkml.kernel.org/r/20210317062402.533919-3-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:13 +08:00
pud = pud_offset(p4d, addr);
if (pud_none(*pud))
return NULL;
if (pud_leaf(*pud))
return pud_page(*pud) + ((addr & ~PUD_MASK) >> PAGE_SHIFT);
if (WARN_ON_ONCE(pud_bad(*pud)))
return NULL;
mm/vmalloc: fix HUGE_VMAP regression by enabling huge pages in vmalloc_to_page vmalloc_to_page returns NULL for addresses mapped by larger pages[*]. Whether or not a vmap is huge depends on the architecture details, alignments, boot options, etc., which the caller can not be expected to know. Therefore HUGE_VMAP is a regression for vmalloc_to_page. This change teaches vmalloc_to_page about larger pages, and returns the struct page that corresponds to the offset within the large page. This makes the API agnostic to mapping implementation details. [*] As explained by commit 029c54b095995 ("mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings") [npiggin@gmail.com: sparc32: add stub pud_page define for walking huge vmalloc page tables] Link: https://lkml.kernel.org/r/20210324232825.1157363-1-npiggin@gmail.com Link: https://lkml.kernel.org/r/20210317062402.533919-3-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:13 +08:00
pmd = pmd_offset(pud, addr);
mm/vmalloc: fix HUGE_VMAP regression by enabling huge pages in vmalloc_to_page vmalloc_to_page returns NULL for addresses mapped by larger pages[*]. Whether or not a vmap is huge depends on the architecture details, alignments, boot options, etc., which the caller can not be expected to know. Therefore HUGE_VMAP is a regression for vmalloc_to_page. This change teaches vmalloc_to_page about larger pages, and returns the struct page that corresponds to the offset within the large page. This makes the API agnostic to mapping implementation details. [*] As explained by commit 029c54b095995 ("mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings") [npiggin@gmail.com: sparc32: add stub pud_page define for walking huge vmalloc page tables] Link: https://lkml.kernel.org/r/20210324232825.1157363-1-npiggin@gmail.com Link: https://lkml.kernel.org/r/20210317062402.533919-3-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:13 +08:00
if (pmd_none(*pmd))
return NULL;
if (pmd_leaf(*pmd))
return pmd_page(*pmd) + ((addr & ~PMD_MASK) >> PAGE_SHIFT);
if (WARN_ON_ONCE(pmd_bad(*pmd)))
return NULL;
mm/vmalloc: vmalloc_to_page() use pte_offset_kernel() vmalloc_to_page() was using pte_offset_map() (followed by pte_unmap()), but it's intended for userspace page tables: prefer pte_offset_kernel(). Link: https://lkml.kernel.org/r/696386a-84f8-b33c-82e5-f865ed6eb39@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Christoph Hellwig <hch@infradead.org> Cc: David Hildenbrand <david@redhat.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Song Liu <song@kernel.org> Cc: Steven Price <steven.price@arm.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Cc: Zack Rusin <zackr@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-09 09:21:41 +08:00
ptep = pte_offset_kernel(pmd, addr);
mm: ptep_get() conversion Convert all instances of direct pte_t* dereferencing to instead use ptep_get() helper. This means that by default, the accesses change from a C dereference to a READ_ONCE(). This is technically the correct thing to do since where pgtables are modified by HW (for access/dirty) they are volatile and therefore we should always ensure READ_ONCE() semantics. But more importantly, by always using the helper, it can be overridden by the architecture to fully encapsulate the contents of the pte. Arch code is deliberately not converted, as the arch code knows best. It is intended that arch code (arm64) will override the default with its own implementation that can (e.g.) hide certain bits from the core code, or determine young/dirty status by mixing in state from another source. Conversion was done using Coccinelle: ---- // $ make coccicheck \ // COCCI=ptepget.cocci \ // SPFLAGS="--include-headers" \ // MODE=patch virtual patch @ depends on patch @ pte_t *v; @@ - *v + ptep_get(v) ---- Then reviewed and hand-edited to avoid multiple unnecessary calls to ptep_get(), instead opting to store the result of a single call in a variable, where it is correct to do so. This aims to negate any cost of READ_ONCE() and will benefit arch-overrides that may be more complex. Included is a fix for an issue in an earlier version of this patch that was pointed out by kernel test robot. The issue arose because config MMU=n elides definition of the ptep helper functions, including ptep_get(). HUGETLB_PAGE=n configs still define a simple huge_ptep_clear_flush() for linking purposes, which dereferences the ptep. So when both configs are disabled, this caused a build error because ptep_get() is not defined. Fix by continuing to do a direct dereference when MMU=n. This is safe because for this config the arch code cannot be trying to virtualize the ptes because none of the ptep helpers are defined. Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/ Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Christian Brauner <brauner@kernel.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: SeongJae Park <sj@kernel.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 23:15:45 +08:00
pte = ptep_get(ptep);
if (pte_present(pte))
page = pte_page(pte);
mm/vmalloc: fix HUGE_VMAP regression by enabling huge pages in vmalloc_to_page vmalloc_to_page returns NULL for addresses mapped by larger pages[*]. Whether or not a vmap is huge depends on the architecture details, alignments, boot options, etc., which the caller can not be expected to know. Therefore HUGE_VMAP is a regression for vmalloc_to_page. This change teaches vmalloc_to_page about larger pages, and returns the struct page that corresponds to the offset within the large page. This makes the API agnostic to mapping implementation details. [*] As explained by commit 029c54b095995 ("mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings") [npiggin@gmail.com: sparc32: add stub pud_page define for walking huge vmalloc page tables] Link: https://lkml.kernel.org/r/20210324232825.1157363-1-npiggin@gmail.com Link: https://lkml.kernel.org/r/20210317062402.533919-3-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:13 +08:00
return page;
}
EXPORT_SYMBOL(vmalloc_to_page);
/*
* Map a vmalloc()-space virtual address to the physical page frame number.
*/
unsigned long vmalloc_to_pfn(const void *vmalloc_addr)
{
return page_to_pfn(vmalloc_to_page(vmalloc_addr));
}
EXPORT_SYMBOL(vmalloc_to_pfn);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*** Global kva allocator ***/
#define DEBUG_AUGMENT_PROPAGATE_CHECK 0
#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 0
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
static DEFINE_SPINLOCK(free_vmap_area_lock);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
static bool vmap_initialized __read_mostly;
mm: vmap area cache Provide a free area cache for the vmalloc virtual address allocator, based on the algorithm used by the user virtual memory allocator. This reduces the number of rbtree operations and linear traversals over the vmap extents in order to find a free area, by starting off at the last point that a free area was found. The free area cache is reset if areas are freed behind it, or if we are searching for a smaller area or alignment than last time. So allocation patterns are not changed (verified by corner-case and random test cases in userspace testing). This solves a regression caused by lazy vunmap TLB purging introduced in db64fe02 (mm: rewrite vmap layer). That patch will leave extents in the vmap allocator after they are vunmapped, and until a significant number accumulate that can be flushed in a single batch. So in a workload that vmalloc/vfree frequently, a chain of extents will build up from VMALLOC_START address, which have to be iterated over each time (giving an O(n) type of behaviour). After this patch, the search will start from where it left off, giving closer to an amortized O(1). This is verified to solve regressions reported Steven in GFS2, and Avi in KVM. Hugh's update: : I tried out the recent mmotm, and on one machine was fortunate to hit : the BUG_ON(first->va_start < addr) which seems to have been stalling : your vmap area cache patch ever since May. : I can get you addresses etc, I did dump a few out; but once I stared : at them, it was easier just to look at the code: and I cannot see how : you would be so sure that first->va_start < addr, once you've done : that addr = ALIGN(max(...), align) above, if align is over 0x1000 : (align was 0x8000 or 0x4000 in the cases I hit: ioremaps like Steve). : I originally got around it by just changing the : if (first->va_start < addr) { : to : while (first->va_start < addr) { : without thinking about it any further; but that seemed unsatisfactory, : why would we want to loop here when we've got another very similar : loop just below it? : I am never going to admit how long I've spent trying to grasp your : "while (n)" rbtree loop just above this, the one with the peculiar : if (!first && tmp->va_start < addr + size) : in. That's unfamiliar to me, I'm guessing it's designed to save a : subsequent rb_next() in a few circumstances (at risk of then setting : a wrong cached_hole_size?); but they did appear few to me, and I didn't : feel I could sign off something with that in when I don't grasp it, : and it seems responsible for extra code and mistaken BUG_ON below it. : I've reverted to the familiar rbtree loop that find_vma() does (but : with va_end >= addr as you had, to respect the additional guard page): : and then (given that cached_hole_size starts out 0) I don't see the : need for any complications below it. If you do want to keep that loop : as you had it, please add a comment to explain what it's trying to do, : and where addr is relative to first when you emerge from it. : Aren't your tests "size <= cached_hole_size" and : "addr + size > first->va_start" forgetting the guard page we want : before the next area? I've changed those. : I have not changed your many "addr + size - 1 < addr" overflow tests, : but have since come to wonder, shouldn't they be "addr + size < addr" : tests - won't the vend checks go wrong if addr + size is 0? : I have added a few comments - Wolfgang Wander's 2.6.13 description of : 1363c3cd8603a913a27e2995dccbd70d5312d8e6 Avoiding mmap fragmentation : helped me a lot, perhaps a pointer to that would be good too. And I found : it easier to understand when I renamed cached_start slightly and moved the : overflow label down. : This patch would go after your mm-vmap-area-cache.patch in mmotm. : Trivially, nobody is going to get that BUG_ON with this patch, and it : appears to work fine on my machines; but I have not given it anything like : the testing you did on your original, and may have broken all the : performance you were aiming for. Please take a look and test it out : integrate with yours if you're satisfied - thanks. [akpm@linux-foundation.org: add locking comment] Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reported-and-tested-by: Steven Whitehouse <swhiteho@redhat.com> Reported-and-tested-by: Avi Kivity <avi@redhat.com> Tested-by: "Barry J. Marson" <bmarson@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:30:36 +08:00
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* This kmem_cache is used for vmap_area objects. Instead of
* allocating from slab we reuse an object from this cache to
* make things faster. Especially in "no edge" splitting of
* free block.
*/
static struct kmem_cache *vmap_area_cachep;
/*
* This linked list is used in pair with free_vmap_area_root.
* It gives O(1) access to prev/next to perform fast coalescing.
*/
static LIST_HEAD(free_vmap_area_list);
/*
* This augment red-black tree represents the free vmap space.
* All vmap_area objects in this tree are sorted by va->va_start
* address. It is used for allocation and merging when a vmap
* object is released.
*
* Each vmap_area node contains a maximum available free block
* of its sub-tree, right or left. Therefore it is possible to
* find a lowest match of free area.
*/
static struct rb_root free_vmap_area_root = RB_ROOT;
mm/vmalloc.c: preload a CPU with one object for split purpose Refactor the NE_FIT_TYPE split case when it comes to an allocation of one extra object. We need it in order to build a remaining space. The preload is done per CPU in non-atomic context with GFP_KERNEL flags. More permissive parameters can be beneficial for systems which are suffer from high memory pressure or low memory condition. For example on my KVM system(4xCPUs, no swap, 256MB RAM) i can simulate the failure of page allocation with GFP_NOWAIT flags. Using "stress-ng" tool and starting N workers spinning on fork() and exit(), i can trigger below trace: <snip> [ 179.815161] stress-ng-fork: page allocation failure: order:0, mode:0x40800(GFP_NOWAIT|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0 [ 179.815168] CPU: 0 PID: 12612 Comm: stress-ng-fork Not tainted 5.2.0-rc3+ #1003 [ 179.815170] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 [ 179.815171] Call Trace: [ 179.815178] dump_stack+0x5c/0x7b [ 179.815182] warn_alloc+0x108/0x190 [ 179.815187] __alloc_pages_slowpath+0xdc7/0xdf0 [ 179.815191] __alloc_pages_nodemask+0x2de/0x330 [ 179.815194] cache_grow_begin+0x77/0x420 [ 179.815197] fallback_alloc+0x161/0x200 [ 179.815200] kmem_cache_alloc+0x1c9/0x570 [ 179.815202] alloc_vmap_area+0x32c/0x990 [ 179.815206] __get_vm_area_node+0xb0/0x170 [ 179.815208] __vmalloc_node_range+0x6d/0x230 [ 179.815211] ? _do_fork+0xce/0x3d0 [ 179.815213] copy_process.part.46+0x850/0x1b90 [ 179.815215] ? _do_fork+0xce/0x3d0 [ 179.815219] _do_fork+0xce/0x3d0 [ 179.815226] ? __do_page_fault+0x2bf/0x4e0 [ 179.815229] do_syscall_64+0x55/0x130 [ 179.815231] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 179.815234] RIP: 0033:0x7fedec4c738b ... [ 179.815237] RSP: 002b:00007ffda469d730 EFLAGS: 00000246 ORIG_RAX: 0000000000000038 [ 179.815239] RAX: ffffffffffffffda RBX: 00007ffda469d730 RCX: 00007fedec4c738b [ 179.815240] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000001200011 [ 179.815241] RBP: 00007ffda469d780 R08: 00007fededd6e300 R09: 00007ffda47f50a0 [ 179.815242] R10: 00007fededd6e5d0 R11: 0000000000000246 R12: 0000000000000000 [ 179.815243] R13: 0000000000000020 R14: 0000000000000000 R15: 0000000000000000 [ 179.815245] Mem-Info: [ 179.815249] active_anon:12686 inactive_anon:14760 isolated_anon:0 active_file:502 inactive_file:61 isolated_file:70 unevictable:2 dirty:0 writeback:0 unstable:0 slab_reclaimable:2380 slab_unreclaimable:7520 mapped:15069 shmem:14813 pagetables:10833 bounce:0 free:1922 free_pcp:229 free_cma:0 <snip> Link: http://lkml.kernel.org/r/20190606120411.8298-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Roman Gushchin <guro@fb.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-07-12 11:58:57 +08:00
/*
* Preload a CPU with one object for "no edge" split case. The
* aim is to get rid of allocations from the atomic context, thus
* to use more permissive allocation masks.
*/
static DEFINE_PER_CPU(struct vmap_area *, ne_fit_preload_node);
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
/*
* This structure defines a single, solid model where a list and
* rb-tree are part of one entity protected by the lock. Nodes are
* sorted in ascending order, thus for O(1) access to left/right
* neighbors a list is used as well as for sequential traversal.
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
*/
struct rb_list {
struct rb_root root;
struct list_head head;
spinlock_t lock;
};
/*
* A fast size storage contains VAs up to 1M size. A pool consists
* of linked between each other ready to go VAs of certain sizes.
* An index in the pool-array corresponds to number of pages + 1.
*/
#define MAX_VA_SIZE_PAGES 256
struct vmap_pool {
struct list_head head;
unsigned long len;
};
/*
* An effective vmap-node logic. Users make use of nodes instead
* of a global heap. It allows to balance an access and mitigate
* contention.
*/
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
static struct vmap_node {
/* Simple size segregated storage. */
struct vmap_pool pool[MAX_VA_SIZE_PAGES];
spinlock_t pool_lock;
bool skip_populate;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
/* Bookkeeping data of this node. */
struct rb_list busy;
struct rb_list lazy;
/*
* Ready-to-free areas.
*/
struct list_head purge_list;
struct work_struct purge_work;
unsigned long nr_purged;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
} single;
/*
* Initial setup consists of one single node, i.e. a balancing
* is fully disabled. Later on, after vmap is initialized these
* parameters are updated based on a system capacity.
*/
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
static struct vmap_node *vmap_nodes = &single;
static __read_mostly unsigned int nr_vmap_nodes = 1;
static __read_mostly unsigned int vmap_zone_size = 1;
static inline unsigned int
addr_to_node_id(unsigned long addr)
{
return (addr / vmap_zone_size) % nr_vmap_nodes;
}
static inline struct vmap_node *
addr_to_node(unsigned long addr)
{
return &vmap_nodes[addr_to_node_id(addr)];
}
static inline struct vmap_node *
id_to_node(unsigned int id)
{
return &vmap_nodes[id % nr_vmap_nodes];
}
/*
* We use the value 0 to represent "no node", that is why
* an encoded value will be the node-id incremented by 1.
* It is always greater then 0. A valid node_id which can
* be encoded is [0:nr_vmap_nodes - 1]. If a passed node_id
* is not valid 0 is returned.
*/
static unsigned int
encode_vn_id(unsigned int node_id)
{
/* Can store U8_MAX [0:254] nodes. */
if (node_id < nr_vmap_nodes)
return (node_id + 1) << BITS_PER_BYTE;
/* Warn and no node encoded. */
WARN_ONCE(1, "Encode wrong node id (%u)\n", node_id);
return 0;
}
/*
* Returns an encoded node-id, the valid range is within
* [0:nr_vmap_nodes-1] values. Otherwise nr_vmap_nodes is
* returned if extracted data is wrong.
*/
static unsigned int
decode_vn_id(unsigned int val)
{
unsigned int node_id = (val >> BITS_PER_BYTE) - 1;
/* Can store U8_MAX [0:254] nodes. */
if (node_id < nr_vmap_nodes)
return node_id;
/* If it was _not_ zero, warn. */
WARN_ONCE(node_id != UINT_MAX,
"Decode wrong node id (%d)\n", node_id);
return nr_vmap_nodes;
}
static bool
is_vn_id_valid(unsigned int node_id)
{
if (node_id < nr_vmap_nodes)
return true;
return false;
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
static __always_inline unsigned long
va_size(struct vmap_area *va)
{
return (va->va_end - va->va_start);
}
static __always_inline unsigned long
get_subtree_max_size(struct rb_node *node)
{
struct vmap_area *va;
va = rb_entry_safe(node, struct vmap_area, rb_node);
return va ? va->subtree_max_size : 0;
}
mm: vmap area cache Provide a free area cache for the vmalloc virtual address allocator, based on the algorithm used by the user virtual memory allocator. This reduces the number of rbtree operations and linear traversals over the vmap extents in order to find a free area, by starting off at the last point that a free area was found. The free area cache is reset if areas are freed behind it, or if we are searching for a smaller area or alignment than last time. So allocation patterns are not changed (verified by corner-case and random test cases in userspace testing). This solves a regression caused by lazy vunmap TLB purging introduced in db64fe02 (mm: rewrite vmap layer). That patch will leave extents in the vmap allocator after they are vunmapped, and until a significant number accumulate that can be flushed in a single batch. So in a workload that vmalloc/vfree frequently, a chain of extents will build up from VMALLOC_START address, which have to be iterated over each time (giving an O(n) type of behaviour). After this patch, the search will start from where it left off, giving closer to an amortized O(1). This is verified to solve regressions reported Steven in GFS2, and Avi in KVM. Hugh's update: : I tried out the recent mmotm, and on one machine was fortunate to hit : the BUG_ON(first->va_start < addr) which seems to have been stalling : your vmap area cache patch ever since May. : I can get you addresses etc, I did dump a few out; but once I stared : at them, it was easier just to look at the code: and I cannot see how : you would be so sure that first->va_start < addr, once you've done : that addr = ALIGN(max(...), align) above, if align is over 0x1000 : (align was 0x8000 or 0x4000 in the cases I hit: ioremaps like Steve). : I originally got around it by just changing the : if (first->va_start < addr) { : to : while (first->va_start < addr) { : without thinking about it any further; but that seemed unsatisfactory, : why would we want to loop here when we've got another very similar : loop just below it? : I am never going to admit how long I've spent trying to grasp your : "while (n)" rbtree loop just above this, the one with the peculiar : if (!first && tmp->va_start < addr + size) : in. That's unfamiliar to me, I'm guessing it's designed to save a : subsequent rb_next() in a few circumstances (at risk of then setting : a wrong cached_hole_size?); but they did appear few to me, and I didn't : feel I could sign off something with that in when I don't grasp it, : and it seems responsible for extra code and mistaken BUG_ON below it. : I've reverted to the familiar rbtree loop that find_vma() does (but : with va_end >= addr as you had, to respect the additional guard page): : and then (given that cached_hole_size starts out 0) I don't see the : need for any complications below it. If you do want to keep that loop : as you had it, please add a comment to explain what it's trying to do, : and where addr is relative to first when you emerge from it. : Aren't your tests "size <= cached_hole_size" and : "addr + size > first->va_start" forgetting the guard page we want : before the next area? I've changed those. : I have not changed your many "addr + size - 1 < addr" overflow tests, : but have since come to wonder, shouldn't they be "addr + size < addr" : tests - won't the vend checks go wrong if addr + size is 0? : I have added a few comments - Wolfgang Wander's 2.6.13 description of : 1363c3cd8603a913a27e2995dccbd70d5312d8e6 Avoiding mmap fragmentation : helped me a lot, perhaps a pointer to that would be good too. And I found : it easier to understand when I renamed cached_start slightly and moved the : overflow label down. : This patch would go after your mm-vmap-area-cache.patch in mmotm. : Trivially, nobody is going to get that BUG_ON with this patch, and it : appears to work fine on my machines; but I have not given it anything like : the testing you did on your original, and may have broken all the : performance you were aiming for. Please take a look and test it out : integrate with yours if you're satisfied - thanks. [akpm@linux-foundation.org: add locking comment] Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reported-and-tested-by: Steven Whitehouse <swhiteho@redhat.com> Reported-and-tested-by: Avi Kivity <avi@redhat.com> Tested-by: "Barry J. Marson" <bmarson@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:30:36 +08:00
RB_DECLARE_CALLBACKS_MAX(static, free_vmap_area_rb_augment_cb,
struct vmap_area, rb_node, unsigned long, subtree_max_size, va_size)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
static void reclaim_and_purge_vmap_areas(void);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
static BLOCKING_NOTIFIER_HEAD(vmap_notify_list);
mm/vmalloc: Move draining areas out of caller context A caller initiates the drain procces from its context once the drain threshold is reached or passed. There are at least two drawbacks of doing so: a) a caller can be a high-prio or RT task. In that case it can stuck in doing the actual drain of all lazily freed areas. This is not optimal because such tasks usually are latency sensitive where the control should be returned back as soon as possible in order to drive such workloads in time. See 96e2db456135 ("mm/vmalloc: rework the drain logic") b) It is not safe to call vfree() during holding a spinlock due to the vmap_purge_lock mutex. The was a report about this from Zeal Robot <zealci@zte.com.cn> here: https://lore.kernel.org/all/20211222081026.484058-1-chi.minghao@zte.com.cn Moving the drain to the separate work context addresses those issues. v1->v2: - Added prefix "_work" to the drain worker function. v2->v3: - Remove the drain_vmap_work_in_progress. Extra queuing is expectable under heavy load but it can be disregarded because a work will bail out if nothing to be done. Link: https://lkml.kernel.org/r/20220131144058.35608-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-23 05:42:50 +08:00
static void drain_vmap_area_work(struct work_struct *work);
static DECLARE_WORK(drain_vmap_work, drain_vmap_area_work);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
static atomic_long_t nr_vmalloc_pages;
unsigned long vmalloc_nr_pages(void)
{
return atomic_long_read(&nr_vmalloc_pages);
}
mm: vmalloc: fix lockdep warning A lockdep reports a possible deadlock in the find_vmap_area_exceed_addr_lock() function: ============================================ WARNING: possible recursive locking detected 6.9.0-rc1-00060-ged3ccc57b108-dirty #6140 Not tainted -------------------------------------------- drgn/455 is trying to acquire lock: ffff0000c00131d0 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 but task is already holding lock: ffff0000c0011878 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&vn->busy.lock/1); lock(&vn->busy.lock/1); *** DEADLOCK *** indeed it can happen if the find_vmap_area_exceed_addr_lock() gets called concurrently because it tries to acquire two nodes locks. It was done to prevent removing a lowest VA found on a previous step. To address this a lowest VA is found first without holding a node lock where it resides. As a last step we check if a VA still there because it can go away, if removed, proceed with next lowest. [akpm@linux-foundation.org: fix comment typos, per Baoquan] Link: https://lkml.kernel.org/r/20240328140330.4747-1-urezki@gmail.com Fixes: 53becf32aec1 ("mm: vmalloc: support multiple nodes in vread_iter") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Jens Axboe <axboe@kernel.dk> Tested-by: Omar Sandoval <osandov@fb.com> Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-28 22:03:30 +08:00
static struct vmap_area *__find_vmap_area(unsigned long addr, struct rb_root *root)
{
struct rb_node *n = root->rb_node;
addr = (unsigned long)kasan_reset_tag((void *)addr);
while (n) {
struct vmap_area *va;
va = rb_entry(n, struct vmap_area, rb_node);
if (addr < va->va_start)
n = n->rb_left;
else if (addr >= va->va_end)
n = n->rb_right;
else
return va;
}
return NULL;
}
/* Look up the first VA which satisfies addr < va_end, NULL if none. */
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
static struct vmap_area *
__find_vmap_area_exceed_addr(unsigned long addr, struct rb_root *root)
{
struct vmap_area *va = NULL;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct rb_node *n = root->rb_node;
addr = (unsigned long)kasan_reset_tag((void *)addr);
while (n) {
struct vmap_area *tmp;
tmp = rb_entry(n, struct vmap_area, rb_node);
if (tmp->va_end > addr) {
va = tmp;
if (tmp->va_start <= addr)
break;
n = n->rb_left;
} else
n = n->rb_right;
}
return va;
}
/*
* Returns a node where a first VA, that satisfies addr < va_end, resides.
* If success, a node is locked. A user is responsible to unlock it when a
* VA is no longer needed to be accessed.
*
* Returns NULL if nothing found.
*/
static struct vmap_node *
find_vmap_area_exceed_addr_lock(unsigned long addr, struct vmap_area **va)
{
mm: vmalloc: fix lockdep warning A lockdep reports a possible deadlock in the find_vmap_area_exceed_addr_lock() function: ============================================ WARNING: possible recursive locking detected 6.9.0-rc1-00060-ged3ccc57b108-dirty #6140 Not tainted -------------------------------------------- drgn/455 is trying to acquire lock: ffff0000c00131d0 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 but task is already holding lock: ffff0000c0011878 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&vn->busy.lock/1); lock(&vn->busy.lock/1); *** DEADLOCK *** indeed it can happen if the find_vmap_area_exceed_addr_lock() gets called concurrently because it tries to acquire two nodes locks. It was done to prevent removing a lowest VA found on a previous step. To address this a lowest VA is found first without holding a node lock where it resides. As a last step we check if a VA still there because it can go away, if removed, proceed with next lowest. [akpm@linux-foundation.org: fix comment typos, per Baoquan] Link: https://lkml.kernel.org/r/20240328140330.4747-1-urezki@gmail.com Fixes: 53becf32aec1 ("mm: vmalloc: support multiple nodes in vread_iter") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Jens Axboe <axboe@kernel.dk> Tested-by: Omar Sandoval <osandov@fb.com> Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-28 22:03:30 +08:00
unsigned long va_start_lowest;
struct vmap_node *vn;
int i;
mm: vmalloc: fix lockdep warning A lockdep reports a possible deadlock in the find_vmap_area_exceed_addr_lock() function: ============================================ WARNING: possible recursive locking detected 6.9.0-rc1-00060-ged3ccc57b108-dirty #6140 Not tainted -------------------------------------------- drgn/455 is trying to acquire lock: ffff0000c00131d0 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 but task is already holding lock: ffff0000c0011878 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&vn->busy.lock/1); lock(&vn->busy.lock/1); *** DEADLOCK *** indeed it can happen if the find_vmap_area_exceed_addr_lock() gets called concurrently because it tries to acquire two nodes locks. It was done to prevent removing a lowest VA found on a previous step. To address this a lowest VA is found first without holding a node lock where it resides. As a last step we check if a VA still there because it can go away, if removed, proceed with next lowest. [akpm@linux-foundation.org: fix comment typos, per Baoquan] Link: https://lkml.kernel.org/r/20240328140330.4747-1-urezki@gmail.com Fixes: 53becf32aec1 ("mm: vmalloc: support multiple nodes in vread_iter") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Jens Axboe <axboe@kernel.dk> Tested-by: Omar Sandoval <osandov@fb.com> Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-28 22:03:30 +08:00
repeat:
for (i = 0, va_start_lowest = 0; i < nr_vmap_nodes; i++) {
vn = &vmap_nodes[i];
spin_lock(&vn->busy.lock);
mm: vmalloc: fix lockdep warning A lockdep reports a possible deadlock in the find_vmap_area_exceed_addr_lock() function: ============================================ WARNING: possible recursive locking detected 6.9.0-rc1-00060-ged3ccc57b108-dirty #6140 Not tainted -------------------------------------------- drgn/455 is trying to acquire lock: ffff0000c00131d0 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 but task is already holding lock: ffff0000c0011878 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&vn->busy.lock/1); lock(&vn->busy.lock/1); *** DEADLOCK *** indeed it can happen if the find_vmap_area_exceed_addr_lock() gets called concurrently because it tries to acquire two nodes locks. It was done to prevent removing a lowest VA found on a previous step. To address this a lowest VA is found first without holding a node lock where it resides. As a last step we check if a VA still there because it can go away, if removed, proceed with next lowest. [akpm@linux-foundation.org: fix comment typos, per Baoquan] Link: https://lkml.kernel.org/r/20240328140330.4747-1-urezki@gmail.com Fixes: 53becf32aec1 ("mm: vmalloc: support multiple nodes in vread_iter") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Jens Axboe <axboe@kernel.dk> Tested-by: Omar Sandoval <osandov@fb.com> Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-28 22:03:30 +08:00
*va = __find_vmap_area_exceed_addr(addr, &vn->busy.root);
if (*va)
if (!va_start_lowest || (*va)->va_start < va_start_lowest)
va_start_lowest = (*va)->va_start;
spin_unlock(&vn->busy.lock);
}
mm: vmalloc: fix lockdep warning A lockdep reports a possible deadlock in the find_vmap_area_exceed_addr_lock() function: ============================================ WARNING: possible recursive locking detected 6.9.0-rc1-00060-ged3ccc57b108-dirty #6140 Not tainted -------------------------------------------- drgn/455 is trying to acquire lock: ffff0000c00131d0 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 but task is already holding lock: ffff0000c0011878 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&vn->busy.lock/1); lock(&vn->busy.lock/1); *** DEADLOCK *** indeed it can happen if the find_vmap_area_exceed_addr_lock() gets called concurrently because it tries to acquire two nodes locks. It was done to prevent removing a lowest VA found on a previous step. To address this a lowest VA is found first without holding a node lock where it resides. As a last step we check if a VA still there because it can go away, if removed, proceed with next lowest. [akpm@linux-foundation.org: fix comment typos, per Baoquan] Link: https://lkml.kernel.org/r/20240328140330.4747-1-urezki@gmail.com Fixes: 53becf32aec1 ("mm: vmalloc: support multiple nodes in vread_iter") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Jens Axboe <axboe@kernel.dk> Tested-by: Omar Sandoval <osandov@fb.com> Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-28 22:03:30 +08:00
/*
* Check if found VA exists, it might have gone away. In this case we
* repeat the search because a VA has been removed concurrently and we
* need to proceed to the next one, which is a rare case.
*/
if (va_start_lowest) {
vn = addr_to_node(va_start_lowest);
mm: vmalloc: fix lockdep warning A lockdep reports a possible deadlock in the find_vmap_area_exceed_addr_lock() function: ============================================ WARNING: possible recursive locking detected 6.9.0-rc1-00060-ged3ccc57b108-dirty #6140 Not tainted -------------------------------------------- drgn/455 is trying to acquire lock: ffff0000c00131d0 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 but task is already holding lock: ffff0000c0011878 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&vn->busy.lock/1); lock(&vn->busy.lock/1); *** DEADLOCK *** indeed it can happen if the find_vmap_area_exceed_addr_lock() gets called concurrently because it tries to acquire two nodes locks. It was done to prevent removing a lowest VA found on a previous step. To address this a lowest VA is found first without holding a node lock where it resides. As a last step we check if a VA still there because it can go away, if removed, proceed with next lowest. [akpm@linux-foundation.org: fix comment typos, per Baoquan] Link: https://lkml.kernel.org/r/20240328140330.4747-1-urezki@gmail.com Fixes: 53becf32aec1 ("mm: vmalloc: support multiple nodes in vread_iter") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Jens Axboe <axboe@kernel.dk> Tested-by: Omar Sandoval <osandov@fb.com> Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-28 22:03:30 +08:00
spin_lock(&vn->busy.lock);
*va = __find_vmap_area(va_start_lowest, &vn->busy.root);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm: vmalloc: fix lockdep warning A lockdep reports a possible deadlock in the find_vmap_area_exceed_addr_lock() function: ============================================ WARNING: possible recursive locking detected 6.9.0-rc1-00060-ged3ccc57b108-dirty #6140 Not tainted -------------------------------------------- drgn/455 is trying to acquire lock: ffff0000c00131d0 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 but task is already holding lock: ffff0000c0011878 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&vn->busy.lock/1); lock(&vn->busy.lock/1); *** DEADLOCK *** indeed it can happen if the find_vmap_area_exceed_addr_lock() gets called concurrently because it tries to acquire two nodes locks. It was done to prevent removing a lowest VA found on a previous step. To address this a lowest VA is found first without holding a node lock where it resides. As a last step we check if a VA still there because it can go away, if removed, proceed with next lowest. [akpm@linux-foundation.org: fix comment typos, per Baoquan] Link: https://lkml.kernel.org/r/20240328140330.4747-1-urezki@gmail.com Fixes: 53becf32aec1 ("mm: vmalloc: support multiple nodes in vread_iter") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Jens Axboe <axboe@kernel.dk> Tested-by: Omar Sandoval <osandov@fb.com> Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-28 22:03:30 +08:00
if (*va)
return vn;
mm: vmalloc: fix lockdep warning A lockdep reports a possible deadlock in the find_vmap_area_exceed_addr_lock() function: ============================================ WARNING: possible recursive locking detected 6.9.0-rc1-00060-ged3ccc57b108-dirty #6140 Not tainted -------------------------------------------- drgn/455 is trying to acquire lock: ffff0000c00131d0 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 but task is already holding lock: ffff0000c0011878 (&vn->busy.lock/1){+.+.}-{2:2}, at: find_vmap_area_exceed_addr_lock+0x64/0x124 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&vn->busy.lock/1); lock(&vn->busy.lock/1); *** DEADLOCK *** indeed it can happen if the find_vmap_area_exceed_addr_lock() gets called concurrently because it tries to acquire two nodes locks. It was done to prevent removing a lowest VA found on a previous step. To address this a lowest VA is found first without holding a node lock where it resides. As a last step we check if a VA still there because it can go away, if removed, proceed with next lowest. [akpm@linux-foundation.org: fix comment typos, per Baoquan] Link: https://lkml.kernel.org/r/20240328140330.4747-1-urezki@gmail.com Fixes: 53becf32aec1 ("mm: vmalloc: support multiple nodes in vread_iter") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Jens Axboe <axboe@kernel.dk> Tested-by: Omar Sandoval <osandov@fb.com> Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-28 22:03:30 +08:00
spin_unlock(&vn->busy.lock);
goto repeat;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
return NULL;
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* This function returns back addresses of parent node
* and its left or right link for further processing.
*
* Otherwise NULL is returned. In that case all further
* steps regarding inserting of conflicting overlap range
* have to be declined and actually considered as a bug.
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
*/
static __always_inline struct rb_node **
find_va_links(struct vmap_area *va,
struct rb_root *root, struct rb_node *from,
struct rb_node **parent)
{
struct vmap_area *tmp_va;
struct rb_node **link;
if (root) {
link = &root->rb_node;
if (unlikely(!*link)) {
*parent = NULL;
return link;
}
} else {
link = &from;
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* Go to the bottom of the tree. When we hit the last point
* we end up with parent rb_node and correct direction, i name
* it link, where the new va->rb_node will be attached to.
*/
do {
tmp_va = rb_entry(*link, struct vmap_area, rb_node);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* During the traversal we also do some sanity check.
* Trigger the BUG() if there are sides(left/right)
* or full overlaps.
*/
if (va->va_end <= tmp_va->va_start)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
link = &(*link)->rb_left;
else if (va->va_start >= tmp_va->va_end)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
link = &(*link)->rb_right;
else {
WARN(1, "vmalloc bug: 0x%lx-0x%lx overlaps with 0x%lx-0x%lx\n",
va->va_start, va->va_end, tmp_va->va_start, tmp_va->va_end);
return NULL;
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
} while (*link);
*parent = &tmp_va->rb_node;
return link;
}
static __always_inline struct list_head *
get_va_next_sibling(struct rb_node *parent, struct rb_node **link)
{
struct list_head *list;
if (unlikely(!parent))
/*
* The red-black tree where we try to find VA neighbors
* before merging or inserting is empty, i.e. it means
* there is no free vmap space. Normally it does not
* happen but we handle this case anyway.
*/
return NULL;
list = &rb_entry(parent, struct vmap_area, rb_node)->list;
return (&parent->rb_right == link ? list->next : list);
}
static __always_inline void
__link_va(struct vmap_area *va, struct rb_root *root,
struct rb_node *parent, struct rb_node **link,
struct list_head *head, bool augment)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
{
/*
* VA is still not in the list, but we can
* identify its future previous list_head node.
*/
if (likely(parent)) {
head = &rb_entry(parent, struct vmap_area, rb_node)->list;
if (&parent->rb_right != link)
head = head->prev;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/* Insert to the rb-tree */
rb_link_node(&va->rb_node, parent, link);
if (augment) {
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* Some explanation here. Just perform simple insertion
* to the tree. We do not set va->subtree_max_size to
* its current size before calling rb_insert_augmented().
* It is because we populate the tree from the bottom
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* to parent levels when the node _is_ in the tree.
*
* Therefore we set subtree_max_size to zero after insertion,
* to let __augment_tree_propagate_from() puts everything to
* the correct order later on.
*/
rb_insert_augmented(&va->rb_node,
root, &free_vmap_area_rb_augment_cb);
va->subtree_max_size = 0;
} else {
rb_insert_color(&va->rb_node, root);
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/* Address-sort this list */
list_add(&va->list, head);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
static __always_inline void
link_va(struct vmap_area *va, struct rb_root *root,
struct rb_node *parent, struct rb_node **link,
struct list_head *head)
{
__link_va(va, root, parent, link, head, false);
}
static __always_inline void
link_va_augment(struct vmap_area *va, struct rb_root *root,
struct rb_node *parent, struct rb_node **link,
struct list_head *head)
{
__link_va(va, root, parent, link, head, true);
}
static __always_inline void
__unlink_va(struct vmap_area *va, struct rb_root *root, bool augment)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
{
if (WARN_ON(RB_EMPTY_NODE(&va->rb_node)))
return;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (augment)
rb_erase_augmented(&va->rb_node,
root, &free_vmap_area_rb_augment_cb);
else
rb_erase(&va->rb_node, root);
list_del_init(&va->list);
RB_CLEAR_NODE(&va->rb_node);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
}
static __always_inline void
unlink_va(struct vmap_area *va, struct rb_root *root)
{
__unlink_va(va, root, false);
}
static __always_inline void
unlink_va_augment(struct vmap_area *va, struct rb_root *root)
{
__unlink_va(va, root, true);
}
#if DEBUG_AUGMENT_PROPAGATE_CHECK
/*
* Gets called when remove the node and rotate.
*/
static __always_inline unsigned long
compute_subtree_max_size(struct vmap_area *va)
{
return max3(va_size(va),
get_subtree_max_size(va->rb_node.rb_left),
get_subtree_max_size(va->rb_node.rb_right));
}
static void
augment_tree_propagate_check(void)
{
struct vmap_area *va;
unsigned long computed_size;
list_for_each_entry(va, &free_vmap_area_list, list) {
computed_size = compute_subtree_max_size(va);
if (computed_size != va->subtree_max_size)
pr_emerg("tree is corrupted: %lu, %lu\n",
va_size(va), va->subtree_max_size);
}
}
#endif
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* This function populates subtree_max_size from bottom to upper
* levels starting from VA point. The propagation must be done
* when VA size is modified by changing its va_start/va_end. Or
* in case of newly inserting of VA to the tree.
*
* It means that __augment_tree_propagate_from() must be called:
* - After VA has been inserted to the tree(free path);
* - After VA has been shrunk(allocation path);
* - After VA has been increased(merging path).
*
* Please note that, it does not mean that upper parent nodes
* and their subtree_max_size are recalculated all the time up
* to the root node.
*
* 4--8
* /\
* / \
* / \
* 2--2 8--8
*
* For example if we modify the node 4, shrinking it to 2, then
* no any modification is required. If we shrink the node 2 to 1
* its subtree_max_size is updated only, and set to 1. If we shrink
* the node 8 to 6, then its subtree_max_size is set to 6 and parent
* node becomes 4--6.
*/
static __always_inline void
augment_tree_propagate_from(struct vmap_area *va)
{
/*
* Populate the tree from bottom towards the root until
* the calculated maximum available size of checked node
* is equal to its current one.
*/
free_vmap_area_rb_augment_cb_propagate(&va->rb_node, NULL);
#if DEBUG_AUGMENT_PROPAGATE_CHECK
augment_tree_propagate_check();
#endif
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
}
static void
insert_vmap_area(struct vmap_area *va,
struct rb_root *root, struct list_head *head)
{
struct rb_node **link;
struct rb_node *parent;
link = find_va_links(va, root, NULL, &parent);
if (link)
link_va(va, root, parent, link, head);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
}
static void
insert_vmap_area_augment(struct vmap_area *va,
struct rb_node *from, struct rb_root *root,
struct list_head *head)
{
struct rb_node **link;
struct rb_node *parent;
if (from)
link = find_va_links(va, NULL, from, &parent);
else
link = find_va_links(va, root, NULL, &parent);
if (link) {
link_va_augment(va, root, parent, link, head);
augment_tree_propagate_from(va);
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
}
/*
* Merge de-allocated chunk of VA memory with previous
* and next free blocks. If coalesce is not done a new
* free area is inserted. If VA has been merged, it is
* freed.
*
* Please note, it can return NULL in case of overlap
* ranges, followed by WARN() report. Despite it is a
* buggy behaviour, a system can be alive and keep
* ongoing.
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
*/
kasan: support backing vmalloc space with real shadow memory Patch series "kasan: support backing vmalloc space with real shadow memory", v11. Currently, vmalloc space is backed by the early shadow page. This means that kasan is incompatible with VMAP_STACK. This series provides a mechanism to back vmalloc space with real, dynamically allocated memory. I have only wired up x86, because that's the only currently supported arch I can work with easily, but it's very easy to wire up other architectures, and it appears that there is some work-in-progress code to do this on arm64 and s390. This has been discussed before in the context of VMAP_STACK: - https://bugzilla.kernel.org/show_bug.cgi?id=202009 - https://lkml.org/lkml/2018/7/22/198 - https://lkml.org/lkml/2019/7/19/822 In terms of implementation details: Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=1) This is unfortunate but given that this is a debug feature only, not the end of the world. The benchmarks are also a stress-test for the vmalloc subsystem: they're not indicative of an overall 2x slowdown! This patch (of 4): Hook into vmalloc and vmap, and dynamically allocate real shadow memory to back the mappings. Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. To avoid the difficulties around swapping mappings around, this code expects that the part of the shadow region that covers the vmalloc space will not be covered by the early shadow page, but will be left unmapped. This will require changes in arch-specific code. This allows KASAN with VMAP_STACK, and may be helpful for architectures that do not have a separate module space (e.g. powerpc64, which I am currently working on). It also allows relaxing the module alignment back to PAGE_SIZE. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=3D1) This is unfortunate but given that this is a debug feature only, not the end of the world. The full benchmark results are: Performance No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 662004 11404956 17.23 19144610 28.92 1.68 full_fit_alloc_test 710950 12029752 16.92 13184651 18.55 1.10 long_busy_list_alloc_test 9431875 43990172 4.66 82970178 8.80 1.89 random_size_alloc_test 5033626 23061762 4.58 47158834 9.37 2.04 fix_align_alloc_test 1252514 15276910 12.20 31266116 24.96 2.05 random_size_align_alloc_te 1648501 14578321 8.84 25560052 15.51 1.75 align_shift_alloc_test 147 830 5.65 5692 38.72 6.86 pcpu_alloc_test 80732 125520 1.55 140864 1.74 1.12 Total Cycles 119240774314 763211341128 6.40 1390338696894 11.66 1.82 Sequential, 2 cpus No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 1423150 14276550 10.03 27733022 19.49 1.94 full_fit_alloc_test 1754219 14722640 8.39 15030786 8.57 1.02 long_busy_list_alloc_test 11451858 52154973 4.55 107016027 9.34 2.05 random_size_alloc_test 5989020 26735276 4.46 68885923 11.50 2.58 fix_align_alloc_test 2050976 20166900 9.83 50491675 24.62 2.50 random_size_align_alloc_te 2858229 17971700 6.29 38730225 13.55 2.16 align_shift_alloc_test 405 6428 15.87 26253 64.82 4.08 pcpu_alloc_test 127183 151464 1.19 216263 1.70 1.43 Total Cycles 54181269392 308723699764 5.70 650772566394 12.01 2.11 fix_size_alloc_test 1420404 14289308 10.06 27790035 19.56 1.94 full_fit_alloc_test 1736145 14806234 8.53 15274301 8.80 1.03 long_busy_list_alloc_test 11404638 52270785 4.58 107550254 9.43 2.06 random_size_alloc_test 6017006 26650625 4.43 68696127 11.42 2.58 fix_align_alloc_test 2045504 20280985 9.91 50414862 24.65 2.49 random_size_align_alloc_te 2845338 17931018 6.30 38510276 13.53 2.15 align_shift_alloc_test 472 3760 7.97 9656 20.46 2.57 pcpu_alloc_test 118643 132732 1.12 146504 1.23 1.10 Total Cycles 54040011688 309102805492 5.72 651325675652 12.05 2.11 [dja@axtens.net: fixups] Link: http://lkml.kernel.org/r/20191120052719.7201-1-dja@axtens.net Link: https://bugzilla.kernel.org/show_bug.cgi?id=3D202009 Link: http://lkml.kernel.org/r/20191031093909.9228-2-dja@axtens.net Signed-off-by: Mark Rutland <mark.rutland@arm.com> [shadow rework] Signed-off-by: Daniel Axtens <dja@axtens.net> Co-developed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Vasily Gorbik <gor@linux.ibm.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:50 +08:00
static __always_inline struct vmap_area *
__merge_or_add_vmap_area(struct vmap_area *va,
struct rb_root *root, struct list_head *head, bool augment)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
{
struct vmap_area *sibling;
struct list_head *next;
struct rb_node **link;
struct rb_node *parent;
bool merged = false;
/*
* Find a place in the tree where VA potentially will be
* inserted, unless it is merged with its sibling/siblings.
*/
link = find_va_links(va, root, NULL, &parent);
if (!link)
return NULL;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* Get next node of VA to check if merging can be done.
*/
next = get_va_next_sibling(parent, link);
if (unlikely(next == NULL))
goto insert;
/*
* start end
* | |
* |<------VA------>|<-----Next----->|
* | |
* start end
*/
if (next != head) {
sibling = list_entry(next, struct vmap_area, list);
if (sibling->va_start == va->va_end) {
sibling->va_start = va->va_start;
/* Free vmap_area object. */
kmem_cache_free(vmap_area_cachep, va);
/* Point to the new merged area. */
va = sibling;
merged = true;
}
}
/*
* start end
* | |
* |<-----Prev----->|<------VA------>|
* | |
* start end
*/
if (next->prev != head) {
sibling = list_entry(next->prev, struct vmap_area, list);
if (sibling->va_end == va->va_start) {
/*
* If both neighbors are coalesced, it is important
* to unlink the "next" node first, followed by merging
* with "previous" one. Otherwise the tree might not be
* fully populated if a sibling's augmented value is
* "normalized" because of rotation operations.
*/
if (merged)
__unlink_va(va, root, augment);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
sibling->va_end = va->va_end;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/* Free vmap_area object. */
kmem_cache_free(vmap_area_cachep, va);
kasan: support backing vmalloc space with real shadow memory Patch series "kasan: support backing vmalloc space with real shadow memory", v11. Currently, vmalloc space is backed by the early shadow page. This means that kasan is incompatible with VMAP_STACK. This series provides a mechanism to back vmalloc space with real, dynamically allocated memory. I have only wired up x86, because that's the only currently supported arch I can work with easily, but it's very easy to wire up other architectures, and it appears that there is some work-in-progress code to do this on arm64 and s390. This has been discussed before in the context of VMAP_STACK: - https://bugzilla.kernel.org/show_bug.cgi?id=202009 - https://lkml.org/lkml/2018/7/22/198 - https://lkml.org/lkml/2019/7/19/822 In terms of implementation details: Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=1) This is unfortunate but given that this is a debug feature only, not the end of the world. The benchmarks are also a stress-test for the vmalloc subsystem: they're not indicative of an overall 2x slowdown! This patch (of 4): Hook into vmalloc and vmap, and dynamically allocate real shadow memory to back the mappings. Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. To avoid the difficulties around swapping mappings around, this code expects that the part of the shadow region that covers the vmalloc space will not be covered by the early shadow page, but will be left unmapped. This will require changes in arch-specific code. This allows KASAN with VMAP_STACK, and may be helpful for architectures that do not have a separate module space (e.g. powerpc64, which I am currently working on). It also allows relaxing the module alignment back to PAGE_SIZE. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=3D1) This is unfortunate but given that this is a debug feature only, not the end of the world. The full benchmark results are: Performance No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 662004 11404956 17.23 19144610 28.92 1.68 full_fit_alloc_test 710950 12029752 16.92 13184651 18.55 1.10 long_busy_list_alloc_test 9431875 43990172 4.66 82970178 8.80 1.89 random_size_alloc_test 5033626 23061762 4.58 47158834 9.37 2.04 fix_align_alloc_test 1252514 15276910 12.20 31266116 24.96 2.05 random_size_align_alloc_te 1648501 14578321 8.84 25560052 15.51 1.75 align_shift_alloc_test 147 830 5.65 5692 38.72 6.86 pcpu_alloc_test 80732 125520 1.55 140864 1.74 1.12 Total Cycles 119240774314 763211341128 6.40 1390338696894 11.66 1.82 Sequential, 2 cpus No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 1423150 14276550 10.03 27733022 19.49 1.94 full_fit_alloc_test 1754219 14722640 8.39 15030786 8.57 1.02 long_busy_list_alloc_test 11451858 52154973 4.55 107016027 9.34 2.05 random_size_alloc_test 5989020 26735276 4.46 68885923 11.50 2.58 fix_align_alloc_test 2050976 20166900 9.83 50491675 24.62 2.50 random_size_align_alloc_te 2858229 17971700 6.29 38730225 13.55 2.16 align_shift_alloc_test 405 6428 15.87 26253 64.82 4.08 pcpu_alloc_test 127183 151464 1.19 216263 1.70 1.43 Total Cycles 54181269392 308723699764 5.70 650772566394 12.01 2.11 fix_size_alloc_test 1420404 14289308 10.06 27790035 19.56 1.94 full_fit_alloc_test 1736145 14806234 8.53 15274301 8.80 1.03 long_busy_list_alloc_test 11404638 52270785 4.58 107550254 9.43 2.06 random_size_alloc_test 6017006 26650625 4.43 68696127 11.42 2.58 fix_align_alloc_test 2045504 20280985 9.91 50414862 24.65 2.49 random_size_align_alloc_te 2845338 17931018 6.30 38510276 13.53 2.15 align_shift_alloc_test 472 3760 7.97 9656 20.46 2.57 pcpu_alloc_test 118643 132732 1.12 146504 1.23 1.10 Total Cycles 54040011688 309102805492 5.72 651325675652 12.05 2.11 [dja@axtens.net: fixups] Link: http://lkml.kernel.org/r/20191120052719.7201-1-dja@axtens.net Link: https://bugzilla.kernel.org/show_bug.cgi?id=3D202009 Link: http://lkml.kernel.org/r/20191031093909.9228-2-dja@axtens.net Signed-off-by: Mark Rutland <mark.rutland@arm.com> [shadow rework] Signed-off-by: Daniel Axtens <dja@axtens.net> Co-developed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Vasily Gorbik <gor@linux.ibm.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:50 +08:00
/* Point to the new merged area. */
va = sibling;
merged = true;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
}
}
insert:
if (!merged)
__link_va(va, root, parent, link, head, augment);
kasan: support backing vmalloc space with real shadow memory Patch series "kasan: support backing vmalloc space with real shadow memory", v11. Currently, vmalloc space is backed by the early shadow page. This means that kasan is incompatible with VMAP_STACK. This series provides a mechanism to back vmalloc space with real, dynamically allocated memory. I have only wired up x86, because that's the only currently supported arch I can work with easily, but it's very easy to wire up other architectures, and it appears that there is some work-in-progress code to do this on arm64 and s390. This has been discussed before in the context of VMAP_STACK: - https://bugzilla.kernel.org/show_bug.cgi?id=202009 - https://lkml.org/lkml/2018/7/22/198 - https://lkml.org/lkml/2019/7/19/822 In terms of implementation details: Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=1) This is unfortunate but given that this is a debug feature only, not the end of the world. The benchmarks are also a stress-test for the vmalloc subsystem: they're not indicative of an overall 2x slowdown! This patch (of 4): Hook into vmalloc and vmap, and dynamically allocate real shadow memory to back the mappings. Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. To avoid the difficulties around swapping mappings around, this code expects that the part of the shadow region that covers the vmalloc space will not be covered by the early shadow page, but will be left unmapped. This will require changes in arch-specific code. This allows KASAN with VMAP_STACK, and may be helpful for architectures that do not have a separate module space (e.g. powerpc64, which I am currently working on). It also allows relaxing the module alignment back to PAGE_SIZE. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=3D1) This is unfortunate but given that this is a debug feature only, not the end of the world. The full benchmark results are: Performance No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 662004 11404956 17.23 19144610 28.92 1.68 full_fit_alloc_test 710950 12029752 16.92 13184651 18.55 1.10 long_busy_list_alloc_test 9431875 43990172 4.66 82970178 8.80 1.89 random_size_alloc_test 5033626 23061762 4.58 47158834 9.37 2.04 fix_align_alloc_test 1252514 15276910 12.20 31266116 24.96 2.05 random_size_align_alloc_te 1648501 14578321 8.84 25560052 15.51 1.75 align_shift_alloc_test 147 830 5.65 5692 38.72 6.86 pcpu_alloc_test 80732 125520 1.55 140864 1.74 1.12 Total Cycles 119240774314 763211341128 6.40 1390338696894 11.66 1.82 Sequential, 2 cpus No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 1423150 14276550 10.03 27733022 19.49 1.94 full_fit_alloc_test 1754219 14722640 8.39 15030786 8.57 1.02 long_busy_list_alloc_test 11451858 52154973 4.55 107016027 9.34 2.05 random_size_alloc_test 5989020 26735276 4.46 68885923 11.50 2.58 fix_align_alloc_test 2050976 20166900 9.83 50491675 24.62 2.50 random_size_align_alloc_te 2858229 17971700 6.29 38730225 13.55 2.16 align_shift_alloc_test 405 6428 15.87 26253 64.82 4.08 pcpu_alloc_test 127183 151464 1.19 216263 1.70 1.43 Total Cycles 54181269392 308723699764 5.70 650772566394 12.01 2.11 fix_size_alloc_test 1420404 14289308 10.06 27790035 19.56 1.94 full_fit_alloc_test 1736145 14806234 8.53 15274301 8.80 1.03 long_busy_list_alloc_test 11404638 52270785 4.58 107550254 9.43 2.06 random_size_alloc_test 6017006 26650625 4.43 68696127 11.42 2.58 fix_align_alloc_test 2045504 20280985 9.91 50414862 24.65 2.49 random_size_align_alloc_te 2845338 17931018 6.30 38510276 13.53 2.15 align_shift_alloc_test 472 3760 7.97 9656 20.46 2.57 pcpu_alloc_test 118643 132732 1.12 146504 1.23 1.10 Total Cycles 54040011688 309102805492 5.72 651325675652 12.05 2.11 [dja@axtens.net: fixups] Link: http://lkml.kernel.org/r/20191120052719.7201-1-dja@axtens.net Link: https://bugzilla.kernel.org/show_bug.cgi?id=3D202009 Link: http://lkml.kernel.org/r/20191031093909.9228-2-dja@axtens.net Signed-off-by: Mark Rutland <mark.rutland@arm.com> [shadow rework] Signed-off-by: Daniel Axtens <dja@axtens.net> Co-developed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Vasily Gorbik <gor@linux.ibm.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:50 +08:00
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
return va;
}
static __always_inline struct vmap_area *
merge_or_add_vmap_area(struct vmap_area *va,
struct rb_root *root, struct list_head *head)
{
return __merge_or_add_vmap_area(va, root, head, false);
}
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
static __always_inline struct vmap_area *
merge_or_add_vmap_area_augment(struct vmap_area *va,
struct rb_root *root, struct list_head *head)
{
va = __merge_or_add_vmap_area(va, root, head, true);
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
if (va)
augment_tree_propagate_from(va);
kasan: support backing vmalloc space with real shadow memory Patch series "kasan: support backing vmalloc space with real shadow memory", v11. Currently, vmalloc space is backed by the early shadow page. This means that kasan is incompatible with VMAP_STACK. This series provides a mechanism to back vmalloc space with real, dynamically allocated memory. I have only wired up x86, because that's the only currently supported arch I can work with easily, but it's very easy to wire up other architectures, and it appears that there is some work-in-progress code to do this on arm64 and s390. This has been discussed before in the context of VMAP_STACK: - https://bugzilla.kernel.org/show_bug.cgi?id=202009 - https://lkml.org/lkml/2018/7/22/198 - https://lkml.org/lkml/2019/7/19/822 In terms of implementation details: Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=1) This is unfortunate but given that this is a debug feature only, not the end of the world. The benchmarks are also a stress-test for the vmalloc subsystem: they're not indicative of an overall 2x slowdown! This patch (of 4): Hook into vmalloc and vmap, and dynamically allocate real shadow memory to back the mappings. Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. To avoid the difficulties around swapping mappings around, this code expects that the part of the shadow region that covers the vmalloc space will not be covered by the early shadow page, but will be left unmapped. This will require changes in arch-specific code. This allows KASAN with VMAP_STACK, and may be helpful for architectures that do not have a separate module space (e.g. powerpc64, which I am currently working on). It also allows relaxing the module alignment back to PAGE_SIZE. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=3D1) This is unfortunate but given that this is a debug feature only, not the end of the world. The full benchmark results are: Performance No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 662004 11404956 17.23 19144610 28.92 1.68 full_fit_alloc_test 710950 12029752 16.92 13184651 18.55 1.10 long_busy_list_alloc_test 9431875 43990172 4.66 82970178 8.80 1.89 random_size_alloc_test 5033626 23061762 4.58 47158834 9.37 2.04 fix_align_alloc_test 1252514 15276910 12.20 31266116 24.96 2.05 random_size_align_alloc_te 1648501 14578321 8.84 25560052 15.51 1.75 align_shift_alloc_test 147 830 5.65 5692 38.72 6.86 pcpu_alloc_test 80732 125520 1.55 140864 1.74 1.12 Total Cycles 119240774314 763211341128 6.40 1390338696894 11.66 1.82 Sequential, 2 cpus No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 1423150 14276550 10.03 27733022 19.49 1.94 full_fit_alloc_test 1754219 14722640 8.39 15030786 8.57 1.02 long_busy_list_alloc_test 11451858 52154973 4.55 107016027 9.34 2.05 random_size_alloc_test 5989020 26735276 4.46 68885923 11.50 2.58 fix_align_alloc_test 2050976 20166900 9.83 50491675 24.62 2.50 random_size_align_alloc_te 2858229 17971700 6.29 38730225 13.55 2.16 align_shift_alloc_test 405 6428 15.87 26253 64.82 4.08 pcpu_alloc_test 127183 151464 1.19 216263 1.70 1.43 Total Cycles 54181269392 308723699764 5.70 650772566394 12.01 2.11 fix_size_alloc_test 1420404 14289308 10.06 27790035 19.56 1.94 full_fit_alloc_test 1736145 14806234 8.53 15274301 8.80 1.03 long_busy_list_alloc_test 11404638 52270785 4.58 107550254 9.43 2.06 random_size_alloc_test 6017006 26650625 4.43 68696127 11.42 2.58 fix_align_alloc_test 2045504 20280985 9.91 50414862 24.65 2.49 random_size_align_alloc_te 2845338 17931018 6.30 38510276 13.53 2.15 align_shift_alloc_test 472 3760 7.97 9656 20.46 2.57 pcpu_alloc_test 118643 132732 1.12 146504 1.23 1.10 Total Cycles 54040011688 309102805492 5.72 651325675652 12.05 2.11 [dja@axtens.net: fixups] Link: http://lkml.kernel.org/r/20191120052719.7201-1-dja@axtens.net Link: https://bugzilla.kernel.org/show_bug.cgi?id=3D202009 Link: http://lkml.kernel.org/r/20191031093909.9228-2-dja@axtens.net Signed-off-by: Mark Rutland <mark.rutland@arm.com> [shadow rework] Signed-off-by: Daniel Axtens <dja@axtens.net> Co-developed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Vasily Gorbik <gor@linux.ibm.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:50 +08:00
return va;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
}
static __always_inline bool
is_within_this_va(struct vmap_area *va, unsigned long size,
unsigned long align, unsigned long vstart)
{
unsigned long nva_start_addr;
if (va->va_start > vstart)
nva_start_addr = ALIGN(va->va_start, align);
else
nva_start_addr = ALIGN(vstart, align);
/* Can be overflowed due to big size or alignment. */
if (nva_start_addr + size < nva_start_addr ||
nva_start_addr < vstart)
return false;
return (nva_start_addr + size <= va->va_end);
}
/*
* Find the first free block(lowest start address) in the tree,
* that will accomplish the request corresponding to passing
* parameters. Please note, with an alignment bigger than PAGE_SIZE,
* a search length is adjusted to account for worst case alignment
* overhead.
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
*/
static __always_inline struct vmap_area *
find_vmap_lowest_match(struct rb_root *root, unsigned long size,
unsigned long align, unsigned long vstart, bool adjust_search_size)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
{
struct vmap_area *va;
struct rb_node *node;
unsigned long length;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/* Start from the root. */
node = root->rb_node;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/* Adjust the search size for alignment overhead. */
length = adjust_search_size ? size + align - 1 : size;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
while (node) {
va = rb_entry(node, struct vmap_area, rb_node);
if (get_subtree_max_size(node->rb_left) >= length &&
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
vstart < va->va_start) {
node = node->rb_left;
} else {
if (is_within_this_va(va, size, align, vstart))
return va;
/*
* Does not make sense to go deeper towards the right
* sub-tree if it does not have a free block that is
* equal or bigger to the requested search length.
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
*/
if (get_subtree_max_size(node->rb_right) >= length) {
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
node = node->rb_right;
continue;
}
/*
* OK. We roll back and find the first right sub-tree,
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* that will satisfy the search criteria. It can happen
mm/vmalloc: do not adjust the search size for alignment overhead We used to include an alignment overhead into a search length, in that case we guarantee that a found area will definitely fit after applying a specific alignment that user specifies. From the other hand we do not guarantee that an area has the lowest address if an alignment is >= PAGE_SIZE. It means that, when a user specifies a special alignment together with a range that corresponds to an exact requested size then an allocation will fail. This is what happens to KASAN, it wants the free block that exactly matches a specified range during onlining memory banks: [root@vm-0 fedora]# echo online > /sys/devices/system/memory/memory82/state [root@vm-0 fedora]# echo online > /sys/devices/system/memory/memory83/state [root@vm-0 fedora]# echo online > /sys/devices/system/memory/memory85/state [root@vm-0 fedora]# echo online > /sys/devices/system/memory/memory84/state vmap allocation for size 16777216 failed: use vmalloc=<size> to increase size bash: vmalloc: allocation failure: 16777216 bytes, mode:0x6000c0(GFP_KERNEL), nodemask=(null),cpuset=/,mems_allowed=0 CPU: 4 PID: 1644 Comm: bash Kdump: loaded Not tainted 4.18.0-339.el8.x86_64+debug #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 Call Trace: dump_stack+0x8e/0xd0 warn_alloc.cold.90+0x8a/0x1b2 ? zone_watermark_ok_safe+0x300/0x300 ? slab_free_freelist_hook+0x85/0x1a0 ? __get_vm_area_node+0x240/0x2c0 ? kfree+0xdd/0x570 ? kmem_cache_alloc_node_trace+0x157/0x230 ? notifier_call_chain+0x90/0x160 __vmalloc_node_range+0x465/0x840 ? mark_held_locks+0xb7/0x120 Fix it by making sure that find_vmap_lowest_match() returns lowest start address with any given alignment value, i.e. for alignments bigger then PAGE_SIZE the algorithm rolls back toward parent nodes checking right sub-trees if the most left free block did not fit due to alignment overhead. Link: https://lkml.kernel.org/r/20211004142829.22222-1-urezki@gmail.com Fixes: 68ad4a330433 ("mm/vmalloc.c: keep track of free blocks for vmap allocation") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Ping Fang <pifang@redhat.com> Tested-by: David Hildenbrand <david@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:31 +08:00
* due to "vstart" restriction or an alignment overhead
* that is bigger then PAGE_SIZE.
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
*/
while ((node = rb_parent(node))) {
va = rb_entry(node, struct vmap_area, rb_node);
if (is_within_this_va(va, size, align, vstart))
return va;
if (get_subtree_max_size(node->rb_right) >= length &&
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
vstart <= va->va_start) {
mm/vmalloc: do not adjust the search size for alignment overhead We used to include an alignment overhead into a search length, in that case we guarantee that a found area will definitely fit after applying a specific alignment that user specifies. From the other hand we do not guarantee that an area has the lowest address if an alignment is >= PAGE_SIZE. It means that, when a user specifies a special alignment together with a range that corresponds to an exact requested size then an allocation will fail. This is what happens to KASAN, it wants the free block that exactly matches a specified range during onlining memory banks: [root@vm-0 fedora]# echo online > /sys/devices/system/memory/memory82/state [root@vm-0 fedora]# echo online > /sys/devices/system/memory/memory83/state [root@vm-0 fedora]# echo online > /sys/devices/system/memory/memory85/state [root@vm-0 fedora]# echo online > /sys/devices/system/memory/memory84/state vmap allocation for size 16777216 failed: use vmalloc=<size> to increase size bash: vmalloc: allocation failure: 16777216 bytes, mode:0x6000c0(GFP_KERNEL), nodemask=(null),cpuset=/,mems_allowed=0 CPU: 4 PID: 1644 Comm: bash Kdump: loaded Not tainted 4.18.0-339.el8.x86_64+debug #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 Call Trace: dump_stack+0x8e/0xd0 warn_alloc.cold.90+0x8a/0x1b2 ? zone_watermark_ok_safe+0x300/0x300 ? slab_free_freelist_hook+0x85/0x1a0 ? __get_vm_area_node+0x240/0x2c0 ? kfree+0xdd/0x570 ? kmem_cache_alloc_node_trace+0x157/0x230 ? notifier_call_chain+0x90/0x160 __vmalloc_node_range+0x465/0x840 ? mark_held_locks+0xb7/0x120 Fix it by making sure that find_vmap_lowest_match() returns lowest start address with any given alignment value, i.e. for alignments bigger then PAGE_SIZE the algorithm rolls back toward parent nodes checking right sub-trees if the most left free block did not fit due to alignment overhead. Link: https://lkml.kernel.org/r/20211004142829.22222-1-urezki@gmail.com Fixes: 68ad4a330433 ("mm/vmalloc.c: keep track of free blocks for vmap allocation") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Ping Fang <pifang@redhat.com> Tested-by: David Hildenbrand <david@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:31 +08:00
/*
* Shift the vstart forward. Please note, we update it with
* parent's start address adding "1" because we do not want
* to enter same sub-tree after it has already been checked
* and no suitable free block found there.
*/
vstart = va->va_start + 1;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
node = node->rb_right;
break;
}
}
}
}
return NULL;
}
#if DEBUG_AUGMENT_LOWEST_MATCH_CHECK
#include <linux/random.h>
static struct vmap_area *
mm/vmalloc: extend find_vmap_lowest_match_check with extra arguments find_vmap_lowest_match() is now able to handle different roots. With DEBUG_AUGMENT_LOWEST_MATCH_CHECK enabled as: : --- a/mm/vmalloc.c : +++ b/mm/vmalloc.c : @@ -713,7 +713,7 @@ EXPORT_SYMBOL(vmalloc_to_pfn); : /*** Global kva allocator ***/ : : -#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 0 : +#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 1 compilation failed as: mm/vmalloc.c: In function 'find_vmap_lowest_match_check': mm/vmalloc.c:1328:32: warning: passing argument 1 of 'find_vmap_lowest_match' makes pointer from integer without a cast [-Wint-conversion] 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~ | | | long unsigned int mm/vmalloc.c:1236:40: note: expected 'struct rb_root *' but argument is of type 'long unsigned int' 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ~~~~~~~~~~~~~~~~^~~~ mm/vmalloc.c:1328:9: error: too few arguments to function 'find_vmap_lowest_match' 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~~~~~~~~~~~~~~~~~~~ mm/vmalloc.c:1236:1: note: declared here 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ^~~~~~~~~~~~~~~~~~~~~~ Extend find_vmap_lowest_match_check() and find_vmap_lowest_linear_match() with extra arguments to fix this. Link: https://lkml.kernel.org/r/20220906060548.1127396-1-song@kernel.org Link: https://lkml.kernel.org/r/20220831052734.3423079-1-song@kernel.org Fixes: f9863be49312 ("mm/vmalloc: extend __alloc_vmap_area() with extra arguments") Signed-off-by: Song Liu <song@kernel.org> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-31 13:27:34 +08:00
find_vmap_lowest_linear_match(struct list_head *head, unsigned long size,
unsigned long align, unsigned long vstart)
{
struct vmap_area *va;
mm/vmalloc: extend find_vmap_lowest_match_check with extra arguments find_vmap_lowest_match() is now able to handle different roots. With DEBUG_AUGMENT_LOWEST_MATCH_CHECK enabled as: : --- a/mm/vmalloc.c : +++ b/mm/vmalloc.c : @@ -713,7 +713,7 @@ EXPORT_SYMBOL(vmalloc_to_pfn); : /*** Global kva allocator ***/ : : -#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 0 : +#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 1 compilation failed as: mm/vmalloc.c: In function 'find_vmap_lowest_match_check': mm/vmalloc.c:1328:32: warning: passing argument 1 of 'find_vmap_lowest_match' makes pointer from integer without a cast [-Wint-conversion] 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~ | | | long unsigned int mm/vmalloc.c:1236:40: note: expected 'struct rb_root *' but argument is of type 'long unsigned int' 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ~~~~~~~~~~~~~~~~^~~~ mm/vmalloc.c:1328:9: error: too few arguments to function 'find_vmap_lowest_match' 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~~~~~~~~~~~~~~~~~~~ mm/vmalloc.c:1236:1: note: declared here 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ^~~~~~~~~~~~~~~~~~~~~~ Extend find_vmap_lowest_match_check() and find_vmap_lowest_linear_match() with extra arguments to fix this. Link: https://lkml.kernel.org/r/20220906060548.1127396-1-song@kernel.org Link: https://lkml.kernel.org/r/20220831052734.3423079-1-song@kernel.org Fixes: f9863be49312 ("mm/vmalloc: extend __alloc_vmap_area() with extra arguments") Signed-off-by: Song Liu <song@kernel.org> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-31 13:27:34 +08:00
list_for_each_entry(va, head, list) {
if (!is_within_this_va(va, size, align, vstart))
continue;
return va;
}
return NULL;
}
static void
mm/vmalloc: extend find_vmap_lowest_match_check with extra arguments find_vmap_lowest_match() is now able to handle different roots. With DEBUG_AUGMENT_LOWEST_MATCH_CHECK enabled as: : --- a/mm/vmalloc.c : +++ b/mm/vmalloc.c : @@ -713,7 +713,7 @@ EXPORT_SYMBOL(vmalloc_to_pfn); : /*** Global kva allocator ***/ : : -#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 0 : +#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 1 compilation failed as: mm/vmalloc.c: In function 'find_vmap_lowest_match_check': mm/vmalloc.c:1328:32: warning: passing argument 1 of 'find_vmap_lowest_match' makes pointer from integer without a cast [-Wint-conversion] 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~ | | | long unsigned int mm/vmalloc.c:1236:40: note: expected 'struct rb_root *' but argument is of type 'long unsigned int' 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ~~~~~~~~~~~~~~~~^~~~ mm/vmalloc.c:1328:9: error: too few arguments to function 'find_vmap_lowest_match' 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~~~~~~~~~~~~~~~~~~~ mm/vmalloc.c:1236:1: note: declared here 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ^~~~~~~~~~~~~~~~~~~~~~ Extend find_vmap_lowest_match_check() and find_vmap_lowest_linear_match() with extra arguments to fix this. Link: https://lkml.kernel.org/r/20220906060548.1127396-1-song@kernel.org Link: https://lkml.kernel.org/r/20220831052734.3423079-1-song@kernel.org Fixes: f9863be49312 ("mm/vmalloc: extend __alloc_vmap_area() with extra arguments") Signed-off-by: Song Liu <song@kernel.org> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-31 13:27:34 +08:00
find_vmap_lowest_match_check(struct rb_root *root, struct list_head *head,
unsigned long size, unsigned long align)
{
struct vmap_area *va_1, *va_2;
unsigned long vstart;
unsigned int rnd;
get_random_bytes(&rnd, sizeof(rnd));
vstart = VMALLOC_START + rnd;
mm/vmalloc: extend find_vmap_lowest_match_check with extra arguments find_vmap_lowest_match() is now able to handle different roots. With DEBUG_AUGMENT_LOWEST_MATCH_CHECK enabled as: : --- a/mm/vmalloc.c : +++ b/mm/vmalloc.c : @@ -713,7 +713,7 @@ EXPORT_SYMBOL(vmalloc_to_pfn); : /*** Global kva allocator ***/ : : -#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 0 : +#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 1 compilation failed as: mm/vmalloc.c: In function 'find_vmap_lowest_match_check': mm/vmalloc.c:1328:32: warning: passing argument 1 of 'find_vmap_lowest_match' makes pointer from integer without a cast [-Wint-conversion] 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~ | | | long unsigned int mm/vmalloc.c:1236:40: note: expected 'struct rb_root *' but argument is of type 'long unsigned int' 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ~~~~~~~~~~~~~~~~^~~~ mm/vmalloc.c:1328:9: error: too few arguments to function 'find_vmap_lowest_match' 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~~~~~~~~~~~~~~~~~~~ mm/vmalloc.c:1236:1: note: declared here 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ^~~~~~~~~~~~~~~~~~~~~~ Extend find_vmap_lowest_match_check() and find_vmap_lowest_linear_match() with extra arguments to fix this. Link: https://lkml.kernel.org/r/20220906060548.1127396-1-song@kernel.org Link: https://lkml.kernel.org/r/20220831052734.3423079-1-song@kernel.org Fixes: f9863be49312 ("mm/vmalloc: extend __alloc_vmap_area() with extra arguments") Signed-off-by: Song Liu <song@kernel.org> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-31 13:27:34 +08:00
va_1 = find_vmap_lowest_match(root, size, align, vstart, false);
va_2 = find_vmap_lowest_linear_match(head, size, align, vstart);
if (va_1 != va_2)
pr_emerg("not lowest: t: 0x%p, l: 0x%p, v: 0x%lx\n",
va_1, va_2, vstart);
}
#endif
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
enum fit_type {
NOTHING_FIT = 0,
FL_FIT_TYPE = 1, /* full fit */
LE_FIT_TYPE = 2, /* left edge fit */
RE_FIT_TYPE = 3, /* right edge fit */
NE_FIT_TYPE = 4 /* no edge fit */
};
static __always_inline enum fit_type
classify_va_fit_type(struct vmap_area *va,
unsigned long nva_start_addr, unsigned long size)
{
enum fit_type type;
/* Check if it is within VA. */
if (nva_start_addr < va->va_start ||
nva_start_addr + size > va->va_end)
return NOTHING_FIT;
/* Now classify. */
if (va->va_start == nva_start_addr) {
if (va->va_end == nva_start_addr + size)
type = FL_FIT_TYPE;
else
type = LE_FIT_TYPE;
} else if (va->va_end == nva_start_addr + size) {
type = RE_FIT_TYPE;
} else {
type = NE_FIT_TYPE;
}
return type;
}
static __always_inline int
va_clip(struct rb_root *root, struct list_head *head,
struct vmap_area *va, unsigned long nva_start_addr,
unsigned long size)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
{
struct vmap_area *lva = NULL;
enum fit_type type = classify_va_fit_type(va, nva_start_addr, size);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (type == FL_FIT_TYPE) {
/*
* No need to split VA, it fully fits.
*
* | |
* V NVA V
* |---------------|
*/
unlink_va_augment(va, root);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
kmem_cache_free(vmap_area_cachep, va);
} else if (type == LE_FIT_TYPE) {
/*
* Split left edge of fit VA.
*
* | |
* V NVA V R
* |-------|-------|
*/
va->va_start += size;
} else if (type == RE_FIT_TYPE) {
/*
* Split right edge of fit VA.
*
* | |
* L V NVA V
* |-------|-------|
*/
va->va_end = nva_start_addr;
} else if (type == NE_FIT_TYPE) {
/*
* Split no edge of fit VA.
*
* | |
* L V NVA V R
* |---|-------|---|
*/
mm/vmalloc.c: preload a CPU with one object for split purpose Refactor the NE_FIT_TYPE split case when it comes to an allocation of one extra object. We need it in order to build a remaining space. The preload is done per CPU in non-atomic context with GFP_KERNEL flags. More permissive parameters can be beneficial for systems which are suffer from high memory pressure or low memory condition. For example on my KVM system(4xCPUs, no swap, 256MB RAM) i can simulate the failure of page allocation with GFP_NOWAIT flags. Using "stress-ng" tool and starting N workers spinning on fork() and exit(), i can trigger below trace: <snip> [ 179.815161] stress-ng-fork: page allocation failure: order:0, mode:0x40800(GFP_NOWAIT|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0 [ 179.815168] CPU: 0 PID: 12612 Comm: stress-ng-fork Not tainted 5.2.0-rc3+ #1003 [ 179.815170] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 [ 179.815171] Call Trace: [ 179.815178] dump_stack+0x5c/0x7b [ 179.815182] warn_alloc+0x108/0x190 [ 179.815187] __alloc_pages_slowpath+0xdc7/0xdf0 [ 179.815191] __alloc_pages_nodemask+0x2de/0x330 [ 179.815194] cache_grow_begin+0x77/0x420 [ 179.815197] fallback_alloc+0x161/0x200 [ 179.815200] kmem_cache_alloc+0x1c9/0x570 [ 179.815202] alloc_vmap_area+0x32c/0x990 [ 179.815206] __get_vm_area_node+0xb0/0x170 [ 179.815208] __vmalloc_node_range+0x6d/0x230 [ 179.815211] ? _do_fork+0xce/0x3d0 [ 179.815213] copy_process.part.46+0x850/0x1b90 [ 179.815215] ? _do_fork+0xce/0x3d0 [ 179.815219] _do_fork+0xce/0x3d0 [ 179.815226] ? __do_page_fault+0x2bf/0x4e0 [ 179.815229] do_syscall_64+0x55/0x130 [ 179.815231] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 179.815234] RIP: 0033:0x7fedec4c738b ... [ 179.815237] RSP: 002b:00007ffda469d730 EFLAGS: 00000246 ORIG_RAX: 0000000000000038 [ 179.815239] RAX: ffffffffffffffda RBX: 00007ffda469d730 RCX: 00007fedec4c738b [ 179.815240] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000001200011 [ 179.815241] RBP: 00007ffda469d780 R08: 00007fededd6e300 R09: 00007ffda47f50a0 [ 179.815242] R10: 00007fededd6e5d0 R11: 0000000000000246 R12: 0000000000000000 [ 179.815243] R13: 0000000000000020 R14: 0000000000000000 R15: 0000000000000000 [ 179.815245] Mem-Info: [ 179.815249] active_anon:12686 inactive_anon:14760 isolated_anon:0 active_file:502 inactive_file:61 isolated_file:70 unevictable:2 dirty:0 writeback:0 unstable:0 slab_reclaimable:2380 slab_unreclaimable:7520 mapped:15069 shmem:14813 pagetables:10833 bounce:0 free:1922 free_pcp:229 free_cma:0 <snip> Link: http://lkml.kernel.org/r/20190606120411.8298-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Roman Gushchin <guro@fb.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-07-12 11:58:57 +08:00
lva = __this_cpu_xchg(ne_fit_preload_node, NULL);
if (unlikely(!lva)) {
/*
* For percpu allocator we do not do any pre-allocation
* and leave it as it is. The reason is it most likely
* never ends up with NE_FIT_TYPE splitting. In case of
* percpu allocations offsets and sizes are aligned to
* fixed align request, i.e. RE_FIT_TYPE and FL_FIT_TYPE
* are its main fitting cases.
*
* There are a few exceptions though, as an example it is
* a first allocation (early boot up) when we have "one"
* big free space that has to be split.
*
* Also we can hit this path in case of regular "vmap"
* allocations, if "this" current CPU was not preloaded.
* See the comment in alloc_vmap_area() why. If so, then
* GFP_NOWAIT is used instead to get an extra object for
* split purpose. That is rare and most time does not
* occur.
*
* What happens if an allocation gets failed. Basically,
* an "overflow" path is triggered to purge lazily freed
* areas to free some memory, then, the "retry" path is
* triggered to repeat one more time. See more details
* in alloc_vmap_area() function.
mm/vmalloc.c: preload a CPU with one object for split purpose Refactor the NE_FIT_TYPE split case when it comes to an allocation of one extra object. We need it in order to build a remaining space. The preload is done per CPU in non-atomic context with GFP_KERNEL flags. More permissive parameters can be beneficial for systems which are suffer from high memory pressure or low memory condition. For example on my KVM system(4xCPUs, no swap, 256MB RAM) i can simulate the failure of page allocation with GFP_NOWAIT flags. Using "stress-ng" tool and starting N workers spinning on fork() and exit(), i can trigger below trace: <snip> [ 179.815161] stress-ng-fork: page allocation failure: order:0, mode:0x40800(GFP_NOWAIT|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0 [ 179.815168] CPU: 0 PID: 12612 Comm: stress-ng-fork Not tainted 5.2.0-rc3+ #1003 [ 179.815170] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 [ 179.815171] Call Trace: [ 179.815178] dump_stack+0x5c/0x7b [ 179.815182] warn_alloc+0x108/0x190 [ 179.815187] __alloc_pages_slowpath+0xdc7/0xdf0 [ 179.815191] __alloc_pages_nodemask+0x2de/0x330 [ 179.815194] cache_grow_begin+0x77/0x420 [ 179.815197] fallback_alloc+0x161/0x200 [ 179.815200] kmem_cache_alloc+0x1c9/0x570 [ 179.815202] alloc_vmap_area+0x32c/0x990 [ 179.815206] __get_vm_area_node+0xb0/0x170 [ 179.815208] __vmalloc_node_range+0x6d/0x230 [ 179.815211] ? _do_fork+0xce/0x3d0 [ 179.815213] copy_process.part.46+0x850/0x1b90 [ 179.815215] ? _do_fork+0xce/0x3d0 [ 179.815219] _do_fork+0xce/0x3d0 [ 179.815226] ? __do_page_fault+0x2bf/0x4e0 [ 179.815229] do_syscall_64+0x55/0x130 [ 179.815231] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 179.815234] RIP: 0033:0x7fedec4c738b ... [ 179.815237] RSP: 002b:00007ffda469d730 EFLAGS: 00000246 ORIG_RAX: 0000000000000038 [ 179.815239] RAX: ffffffffffffffda RBX: 00007ffda469d730 RCX: 00007fedec4c738b [ 179.815240] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000001200011 [ 179.815241] RBP: 00007ffda469d780 R08: 00007fededd6e300 R09: 00007ffda47f50a0 [ 179.815242] R10: 00007fededd6e5d0 R11: 0000000000000246 R12: 0000000000000000 [ 179.815243] R13: 0000000000000020 R14: 0000000000000000 R15: 0000000000000000 [ 179.815245] Mem-Info: [ 179.815249] active_anon:12686 inactive_anon:14760 isolated_anon:0 active_file:502 inactive_file:61 isolated_file:70 unevictable:2 dirty:0 writeback:0 unstable:0 slab_reclaimable:2380 slab_unreclaimable:7520 mapped:15069 shmem:14813 pagetables:10833 bounce:0 free:1922 free_pcp:229 free_cma:0 <snip> Link: http://lkml.kernel.org/r/20190606120411.8298-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Roman Gushchin <guro@fb.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-07-12 11:58:57 +08:00
*/
lva = kmem_cache_alloc(vmap_area_cachep, GFP_NOWAIT);
if (!lva)
return -1;
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* Build the remainder.
*/
lva->va_start = va->va_start;
lva->va_end = nva_start_addr;
/*
* Shrink this VA to remaining size.
*/
va->va_start = nva_start_addr + size;
} else {
return -1;
}
if (type != FL_FIT_TYPE) {
augment_tree_propagate_from(va);
if (lva) /* type == NE_FIT_TYPE */
insert_vmap_area_augment(lva, &va->rb_node, root, head);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
}
return 0;
}
mm: vmalloc: add va_alloc() helper Patch series "Mitigate a vmap lock contention", v3. 1. Motivation - Offload global vmap locks making it scaled to number of CPUS; - If possible and there is an agreement, we can remove the "Per cpu kva allocator" to make the vmap code to be more simple; - There were complaints from XFS folk that a vmalloc might be contented on their workloads. 2. Design(high level overview) We introduce an effective vmap node logic. A node behaves as independent entity to serve an allocation request directly(if possible) from its pool. That way it bypasses a global vmap space that is protected by its own lock. An access to pools are serialized by CPUs. Number of nodes are equal to number of CPUs in a system. Please note the high threshold is bound to 128 nodes. Pools are size segregated and populated based on system demand. The maximum alloc request that can be stored into a segregated storage is 256 pages. The lazily drain path decays a pool by 25% as a first step and as second populates it by fresh freed VAs for reuse instead of returning them into a global space. When a VA is obtained(alloc path), it is stored in separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. Doing so we balance VAs across the nodes as a result an access becomes scalable. The addr_to_node() function does a proper address conversion to a correct node. A vmap space is divided on segments with fixed size, it is 16 pages. That way any address can be associated with a segment number. Number of segments are equal to num_possible_cpus() but not grater then 128. The numeration starts from 0. See below how it is converted: static inline unsigned int addr_to_node_id(unsigned long addr) { return (addr / zone_size) % nr_nodes; } On a free path, a VA can be easily found by converting its "va_start" address to a certain node it resides. It is moved from "busy" data to "lazy" data structure. Later on, as noted earlier, the lazy kworker decays each node pool and populates it by fresh incoming VAs. Please note, a VA is returned to a node that did an alloc request. 3. Test on AMD Ryzen Threadripper 3970X 32-Core Processor sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 <default perf> 94.41% 0.89% [kernel] [k] _raw_spin_lock 93.35% 93.07% [kernel] [k] native_queued_spin_lock_slowpath 76.13% 0.28% [kernel] [k] __vmalloc_node_range 72.96% 0.81% [kernel] [k] alloc_vmap_area 56.94% 0.00% [kernel] [k] __get_vm_area_node 41.95% 0.00% [kernel] [k] vmalloc 37.15% 0.01% [test_vmalloc] [k] full_fit_alloc_test 35.17% 0.00% [kernel] [k] ret_from_fork_asm 35.17% 0.00% [kernel] [k] ret_from_fork 35.17% 0.00% [kernel] [k] kthread 35.08% 0.00% [test_vmalloc] [k] test_func 34.45% 0.00% [test_vmalloc] [k] fix_size_alloc_test 28.09% 0.01% [test_vmalloc] [k] long_busy_list_alloc_test 23.53% 0.25% [kernel] [k] vfree.part.0 21.72% 0.00% [kernel] [k] remove_vm_area 20.08% 0.21% [kernel] [k] find_unlink_vmap_area 2.34% 0.61% [kernel] [k] free_vmap_area_noflush <default perf> vs <patch-series perf> 82.32% 0.22% [test_vmalloc] [k] long_busy_list_alloc_test 63.36% 0.02% [kernel] [k] vmalloc 63.34% 2.64% [kernel] [k] __vmalloc_node_range 30.42% 4.46% [kernel] [k] vfree.part.0 28.98% 2.51% [kernel] [k] __alloc_pages_bulk 27.28% 0.19% [kernel] [k] __get_vm_area_node 26.13% 1.50% [kernel] [k] alloc_vmap_area 21.72% 21.67% [kernel] [k] clear_page_rep 19.51% 2.43% [kernel] [k] _raw_spin_lock 16.61% 16.51% [kernel] [k] native_queued_spin_lock_slowpath 13.40% 2.07% [kernel] [k] free_unref_page 10.62% 0.01% [kernel] [k] remove_vm_area 9.02% 8.73% [kernel] [k] insert_vmap_area 8.94% 0.00% [kernel] [k] ret_from_fork_asm 8.94% 0.00% [kernel] [k] ret_from_fork 8.94% 0.00% [kernel] [k] kthread 8.29% 0.00% [test_vmalloc] [k] test_func 7.81% 0.05% [test_vmalloc] [k] full_fit_alloc_test 5.30% 4.73% [kernel] [k] purge_vmap_node 4.47% 2.65% [kernel] [k] free_vmap_area_noflush <patch-series perf> confirms that a native_queued_spin_lock_slowpath goes down to 16.51% percent from 93.07%. The throughput is ~12x higher: urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 10m51.271s user 0m0.013s sys 0m0.187s urezki@pc638:~$ urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 0m51.301s user 0m0.015s sys 0m0.040s urezki@pc638:~$ This patch (of 11): Currently __alloc_vmap_area() function contains an open codded logic that finds and adjusts a VA based on allocation request. Introduce a va_alloc() helper that adjusts found VA only. There is no a functional change as a result of this patch. Link: https://lkml.kernel.org/r/20240102184633.748113-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:23 +08:00
static unsigned long
va_alloc(struct vmap_area *va,
struct rb_root *root, struct list_head *head,
unsigned long size, unsigned long align,
unsigned long vstart, unsigned long vend)
{
unsigned long nva_start_addr;
int ret;
if (va->va_start > vstart)
nva_start_addr = ALIGN(va->va_start, align);
else
nva_start_addr = ALIGN(vstart, align);
/* Check the "vend" restriction. */
if (nva_start_addr + size > vend)
return vend;
/* Update the free vmap_area. */
ret = va_clip(root, head, va, nva_start_addr, size);
mm: vmalloc: add va_alloc() helper Patch series "Mitigate a vmap lock contention", v3. 1. Motivation - Offload global vmap locks making it scaled to number of CPUS; - If possible and there is an agreement, we can remove the "Per cpu kva allocator" to make the vmap code to be more simple; - There were complaints from XFS folk that a vmalloc might be contented on their workloads. 2. Design(high level overview) We introduce an effective vmap node logic. A node behaves as independent entity to serve an allocation request directly(if possible) from its pool. That way it bypasses a global vmap space that is protected by its own lock. An access to pools are serialized by CPUs. Number of nodes are equal to number of CPUs in a system. Please note the high threshold is bound to 128 nodes. Pools are size segregated and populated based on system demand. The maximum alloc request that can be stored into a segregated storage is 256 pages. The lazily drain path decays a pool by 25% as a first step and as second populates it by fresh freed VAs for reuse instead of returning them into a global space. When a VA is obtained(alloc path), it is stored in separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. Doing so we balance VAs across the nodes as a result an access becomes scalable. The addr_to_node() function does a proper address conversion to a correct node. A vmap space is divided on segments with fixed size, it is 16 pages. That way any address can be associated with a segment number. Number of segments are equal to num_possible_cpus() but not grater then 128. The numeration starts from 0. See below how it is converted: static inline unsigned int addr_to_node_id(unsigned long addr) { return (addr / zone_size) % nr_nodes; } On a free path, a VA can be easily found by converting its "va_start" address to a certain node it resides. It is moved from "busy" data to "lazy" data structure. Later on, as noted earlier, the lazy kworker decays each node pool and populates it by fresh incoming VAs. Please note, a VA is returned to a node that did an alloc request. 3. Test on AMD Ryzen Threadripper 3970X 32-Core Processor sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 <default perf> 94.41% 0.89% [kernel] [k] _raw_spin_lock 93.35% 93.07% [kernel] [k] native_queued_spin_lock_slowpath 76.13% 0.28% [kernel] [k] __vmalloc_node_range 72.96% 0.81% [kernel] [k] alloc_vmap_area 56.94% 0.00% [kernel] [k] __get_vm_area_node 41.95% 0.00% [kernel] [k] vmalloc 37.15% 0.01% [test_vmalloc] [k] full_fit_alloc_test 35.17% 0.00% [kernel] [k] ret_from_fork_asm 35.17% 0.00% [kernel] [k] ret_from_fork 35.17% 0.00% [kernel] [k] kthread 35.08% 0.00% [test_vmalloc] [k] test_func 34.45% 0.00% [test_vmalloc] [k] fix_size_alloc_test 28.09% 0.01% [test_vmalloc] [k] long_busy_list_alloc_test 23.53% 0.25% [kernel] [k] vfree.part.0 21.72% 0.00% [kernel] [k] remove_vm_area 20.08% 0.21% [kernel] [k] find_unlink_vmap_area 2.34% 0.61% [kernel] [k] free_vmap_area_noflush <default perf> vs <patch-series perf> 82.32% 0.22% [test_vmalloc] [k] long_busy_list_alloc_test 63.36% 0.02% [kernel] [k] vmalloc 63.34% 2.64% [kernel] [k] __vmalloc_node_range 30.42% 4.46% [kernel] [k] vfree.part.0 28.98% 2.51% [kernel] [k] __alloc_pages_bulk 27.28% 0.19% [kernel] [k] __get_vm_area_node 26.13% 1.50% [kernel] [k] alloc_vmap_area 21.72% 21.67% [kernel] [k] clear_page_rep 19.51% 2.43% [kernel] [k] _raw_spin_lock 16.61% 16.51% [kernel] [k] native_queued_spin_lock_slowpath 13.40% 2.07% [kernel] [k] free_unref_page 10.62% 0.01% [kernel] [k] remove_vm_area 9.02% 8.73% [kernel] [k] insert_vmap_area 8.94% 0.00% [kernel] [k] ret_from_fork_asm 8.94% 0.00% [kernel] [k] ret_from_fork 8.94% 0.00% [kernel] [k] kthread 8.29% 0.00% [test_vmalloc] [k] test_func 7.81% 0.05% [test_vmalloc] [k] full_fit_alloc_test 5.30% 4.73% [kernel] [k] purge_vmap_node 4.47% 2.65% [kernel] [k] free_vmap_area_noflush <patch-series perf> confirms that a native_queued_spin_lock_slowpath goes down to 16.51% percent from 93.07%. The throughput is ~12x higher: urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 10m51.271s user 0m0.013s sys 0m0.187s urezki@pc638:~$ urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 0m51.301s user 0m0.015s sys 0m0.040s urezki@pc638:~$ This patch (of 11): Currently __alloc_vmap_area() function contains an open codded logic that finds and adjusts a VA based on allocation request. Introduce a va_alloc() helper that adjusts found VA only. There is no a functional change as a result of this patch. Link: https://lkml.kernel.org/r/20240102184633.748113-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:23 +08:00
if (WARN_ON_ONCE(ret))
return vend;
return nva_start_addr;
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/*
* Returns a start address of the newly allocated area, if success.
* Otherwise a vend is returned that indicates failure.
*/
static __always_inline unsigned long
__alloc_vmap_area(struct rb_root *root, struct list_head *head,
unsigned long size, unsigned long align,
unsigned long vstart, unsigned long vend)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
{
bool adjust_search_size = true;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
unsigned long nva_start_addr;
struct vmap_area *va;
/*
* Do not adjust when:
* a) align <= PAGE_SIZE, because it does not make any sense.
* All blocks(their start addresses) are at least PAGE_SIZE
* aligned anyway;
* b) a short range where a requested size corresponds to exactly
* specified [vstart:vend] interval and an alignment > PAGE_SIZE.
* With adjusted search length an allocation would not succeed.
*/
if (align <= PAGE_SIZE || (align > PAGE_SIZE && (vend - vstart) == size))
adjust_search_size = false;
va = find_vmap_lowest_match(root, size, align, vstart, adjust_search_size);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (unlikely(!va))
return vend;
mm: vmalloc: add va_alloc() helper Patch series "Mitigate a vmap lock contention", v3. 1. Motivation - Offload global vmap locks making it scaled to number of CPUS; - If possible and there is an agreement, we can remove the "Per cpu kva allocator" to make the vmap code to be more simple; - There were complaints from XFS folk that a vmalloc might be contented on their workloads. 2. Design(high level overview) We introduce an effective vmap node logic. A node behaves as independent entity to serve an allocation request directly(if possible) from its pool. That way it bypasses a global vmap space that is protected by its own lock. An access to pools are serialized by CPUs. Number of nodes are equal to number of CPUs in a system. Please note the high threshold is bound to 128 nodes. Pools are size segregated and populated based on system demand. The maximum alloc request that can be stored into a segregated storage is 256 pages. The lazily drain path decays a pool by 25% as a first step and as second populates it by fresh freed VAs for reuse instead of returning them into a global space. When a VA is obtained(alloc path), it is stored in separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. Doing so we balance VAs across the nodes as a result an access becomes scalable. The addr_to_node() function does a proper address conversion to a correct node. A vmap space is divided on segments with fixed size, it is 16 pages. That way any address can be associated with a segment number. Number of segments are equal to num_possible_cpus() but not grater then 128. The numeration starts from 0. See below how it is converted: static inline unsigned int addr_to_node_id(unsigned long addr) { return (addr / zone_size) % nr_nodes; } On a free path, a VA can be easily found by converting its "va_start" address to a certain node it resides. It is moved from "busy" data to "lazy" data structure. Later on, as noted earlier, the lazy kworker decays each node pool and populates it by fresh incoming VAs. Please note, a VA is returned to a node that did an alloc request. 3. Test on AMD Ryzen Threadripper 3970X 32-Core Processor sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 <default perf> 94.41% 0.89% [kernel] [k] _raw_spin_lock 93.35% 93.07% [kernel] [k] native_queued_spin_lock_slowpath 76.13% 0.28% [kernel] [k] __vmalloc_node_range 72.96% 0.81% [kernel] [k] alloc_vmap_area 56.94% 0.00% [kernel] [k] __get_vm_area_node 41.95% 0.00% [kernel] [k] vmalloc 37.15% 0.01% [test_vmalloc] [k] full_fit_alloc_test 35.17% 0.00% [kernel] [k] ret_from_fork_asm 35.17% 0.00% [kernel] [k] ret_from_fork 35.17% 0.00% [kernel] [k] kthread 35.08% 0.00% [test_vmalloc] [k] test_func 34.45% 0.00% [test_vmalloc] [k] fix_size_alloc_test 28.09% 0.01% [test_vmalloc] [k] long_busy_list_alloc_test 23.53% 0.25% [kernel] [k] vfree.part.0 21.72% 0.00% [kernel] [k] remove_vm_area 20.08% 0.21% [kernel] [k] find_unlink_vmap_area 2.34% 0.61% [kernel] [k] free_vmap_area_noflush <default perf> vs <patch-series perf> 82.32% 0.22% [test_vmalloc] [k] long_busy_list_alloc_test 63.36% 0.02% [kernel] [k] vmalloc 63.34% 2.64% [kernel] [k] __vmalloc_node_range 30.42% 4.46% [kernel] [k] vfree.part.0 28.98% 2.51% [kernel] [k] __alloc_pages_bulk 27.28% 0.19% [kernel] [k] __get_vm_area_node 26.13% 1.50% [kernel] [k] alloc_vmap_area 21.72% 21.67% [kernel] [k] clear_page_rep 19.51% 2.43% [kernel] [k] _raw_spin_lock 16.61% 16.51% [kernel] [k] native_queued_spin_lock_slowpath 13.40% 2.07% [kernel] [k] free_unref_page 10.62% 0.01% [kernel] [k] remove_vm_area 9.02% 8.73% [kernel] [k] insert_vmap_area 8.94% 0.00% [kernel] [k] ret_from_fork_asm 8.94% 0.00% [kernel] [k] ret_from_fork 8.94% 0.00% [kernel] [k] kthread 8.29% 0.00% [test_vmalloc] [k] test_func 7.81% 0.05% [test_vmalloc] [k] full_fit_alloc_test 5.30% 4.73% [kernel] [k] purge_vmap_node 4.47% 2.65% [kernel] [k] free_vmap_area_noflush <patch-series perf> confirms that a native_queued_spin_lock_slowpath goes down to 16.51% percent from 93.07%. The throughput is ~12x higher: urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 10m51.271s user 0m0.013s sys 0m0.187s urezki@pc638:~$ urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 0m51.301s user 0m0.015s sys 0m0.040s urezki@pc638:~$ This patch (of 11): Currently __alloc_vmap_area() function contains an open codded logic that finds and adjusts a VA based on allocation request. Introduce a va_alloc() helper that adjusts found VA only. There is no a functional change as a result of this patch. Link: https://lkml.kernel.org/r/20240102184633.748113-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:23 +08:00
nva_start_addr = va_alloc(va, root, head, size, align, vstart, vend);
if (nva_start_addr == vend)
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
return vend;
#if DEBUG_AUGMENT_LOWEST_MATCH_CHECK
mm/vmalloc: extend find_vmap_lowest_match_check with extra arguments find_vmap_lowest_match() is now able to handle different roots. With DEBUG_AUGMENT_LOWEST_MATCH_CHECK enabled as: : --- a/mm/vmalloc.c : +++ b/mm/vmalloc.c : @@ -713,7 +713,7 @@ EXPORT_SYMBOL(vmalloc_to_pfn); : /*** Global kva allocator ***/ : : -#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 0 : +#define DEBUG_AUGMENT_LOWEST_MATCH_CHECK 1 compilation failed as: mm/vmalloc.c: In function 'find_vmap_lowest_match_check': mm/vmalloc.c:1328:32: warning: passing argument 1 of 'find_vmap_lowest_match' makes pointer from integer without a cast [-Wint-conversion] 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~ | | | long unsigned int mm/vmalloc.c:1236:40: note: expected 'struct rb_root *' but argument is of type 'long unsigned int' 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ~~~~~~~~~~~~~~~~^~~~ mm/vmalloc.c:1328:9: error: too few arguments to function 'find_vmap_lowest_match' 1328 | va_1 = find_vmap_lowest_match(size, align, vstart, false); | ^~~~~~~~~~~~~~~~~~~~~~ mm/vmalloc.c:1236:1: note: declared here 1236 | find_vmap_lowest_match(struct rb_root *root, unsigned long size, | ^~~~~~~~~~~~~~~~~~~~~~ Extend find_vmap_lowest_match_check() and find_vmap_lowest_linear_match() with extra arguments to fix this. Link: https://lkml.kernel.org/r/20220906060548.1127396-1-song@kernel.org Link: https://lkml.kernel.org/r/20220831052734.3423079-1-song@kernel.org Fixes: f9863be49312 ("mm/vmalloc: extend __alloc_vmap_area() with extra arguments") Signed-off-by: Song Liu <song@kernel.org> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-31 13:27:34 +08:00
find_vmap_lowest_match_check(root, head, size, align);
#endif
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
return nva_start_addr;
}
/*
* Free a region of KVA allocated by alloc_vmap_area
*/
static void free_vmap_area(struct vmap_area *va)
{
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn = addr_to_node(va->va_start);
/*
* Remove from the busy tree/list.
*/
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
spin_lock(&vn->busy.lock);
unlink_va(va, &vn->busy.root);
spin_unlock(&vn->busy.lock);
/*
* Insert/Merge it back to the free tree/list.
*/
spin_lock(&free_vmap_area_lock);
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
merge_or_add_vmap_area_augment(va, &free_vmap_area_root, &free_vmap_area_list);
spin_unlock(&free_vmap_area_lock);
}
static inline void
preload_this_cpu_lock(spinlock_t *lock, gfp_t gfp_mask, int node)
{
struct vmap_area *va = NULL;
/*
* Preload this CPU with one extra vmap_area object. It is used
* when fit type of free area is NE_FIT_TYPE. It guarantees that
* a CPU that does an allocation is preloaded.
*
* We do it in non-atomic context, thus it allows us to use more
* permissive allocation masks to be more stable under low memory
* condition and high memory pressure.
*/
if (!this_cpu_read(ne_fit_preload_node))
va = kmem_cache_alloc_node(vmap_area_cachep, gfp_mask, node);
spin_lock(lock);
if (va && __this_cpu_cmpxchg(ne_fit_preload_node, NULL, va))
kmem_cache_free(vmap_area_cachep, va);
}
static struct vmap_pool *
size_to_va_pool(struct vmap_node *vn, unsigned long size)
{
unsigned int idx = (size - 1) / PAGE_SIZE;
if (idx < MAX_VA_SIZE_PAGES)
return &vn->pool[idx];
return NULL;
}
static bool
node_pool_add_va(struct vmap_node *n, struct vmap_area *va)
{
struct vmap_pool *vp;
vp = size_to_va_pool(n, va_size(va));
if (!vp)
return false;
spin_lock(&n->pool_lock);
list_add(&va->list, &vp->head);
WRITE_ONCE(vp->len, vp->len + 1);
spin_unlock(&n->pool_lock);
return true;
}
static struct vmap_area *
node_pool_del_va(struct vmap_node *vn, unsigned long size,
unsigned long align, unsigned long vstart,
unsigned long vend)
{
struct vmap_area *va = NULL;
struct vmap_pool *vp;
int err = 0;
vp = size_to_va_pool(vn, size);
if (!vp || list_empty(&vp->head))
return NULL;
spin_lock(&vn->pool_lock);
if (!list_empty(&vp->head)) {
va = list_first_entry(&vp->head, struct vmap_area, list);
if (IS_ALIGNED(va->va_start, align)) {
/*
* Do some sanity check and emit a warning
* if one of below checks detects an error.
*/
err |= (va_size(va) != size);
err |= (va->va_start < vstart);
err |= (va->va_end > vend);
if (!WARN_ON_ONCE(err)) {
list_del_init(&va->list);
WRITE_ONCE(vp->len, vp->len - 1);
} else {
va = NULL;
}
} else {
list_move_tail(&va->list, &vp->head);
va = NULL;
}
}
spin_unlock(&vn->pool_lock);
return va;
}
static struct vmap_area *
node_alloc(unsigned long size, unsigned long align,
unsigned long vstart, unsigned long vend,
unsigned long *addr, unsigned int *vn_id)
{
struct vmap_area *va;
*vn_id = 0;
*addr = vend;
/*
* Fallback to a global heap if not vmalloc or there
* is only one node.
*/
if (vstart != VMALLOC_START || vend != VMALLOC_END ||
nr_vmap_nodes == 1)
return NULL;
*vn_id = raw_smp_processor_id() % nr_vmap_nodes;
va = node_pool_del_va(id_to_node(*vn_id), size, align, vstart, vend);
*vn_id = encode_vn_id(*vn_id);
if (va)
*addr = va->va_start;
return va;
}
mm/vmalloc: eliminated the lock contention from twice to once When allocating a new memory area where the mapping address range is known, it is observed that the vmap_node->busy.lock is acquired twice. The first acquisition occurs in the alloc_vmap_area() function when inserting the vm area into the vm mapping red-black tree. The second acquisition occurs in the setup_vmalloc_vm() function when updating the properties of the vm, such as flags and address, etc. Combine these two operations together in alloc_vmap_area(), which improves scalability when the vmap_node->busy.lock is contended. By doing so, the need to acquire the lock twice can also be eliminated to once. With the above change, tested on intel sapphire rapids platform(224 vcpu), a 4% performance improvement is gained on stress-ng/pthread(https://github.com/ColinIanKing/stress-ng), which is the stress test of thread creations. Link: https://lkml.kernel.org/r/20240307021440.64967-1-rulin.huang@intel.com Co-developed-by: "Chen, Tim C" <tim.c.chen@intel.com> Signed-off-by: "Chen, Tim C" <tim.c.chen@intel.com> Co-developed-by: "King, Colin" <colin.king@intel.com> Signed-off-by: "King, Colin" <colin.king@intel.com> Signed-off-by: rulinhuang <rulin.huang@intel.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Wangyang Guo <wangyang.guo@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-07 10:14:40 +08:00
static inline void setup_vmalloc_vm(struct vm_struct *vm,
struct vmap_area *va, unsigned long flags, const void *caller)
{
vm->flags = flags;
vm->addr = (void *)va->va_start;
vm->size = va->va_end - va->va_start;
vm->caller = caller;
va->vm = vm;
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*
* Allocate a region of KVA of the specified size and alignment, within the
mm/vmalloc: eliminated the lock contention from twice to once When allocating a new memory area where the mapping address range is known, it is observed that the vmap_node->busy.lock is acquired twice. The first acquisition occurs in the alloc_vmap_area() function when inserting the vm area into the vm mapping red-black tree. The second acquisition occurs in the setup_vmalloc_vm() function when updating the properties of the vm, such as flags and address, etc. Combine these two operations together in alloc_vmap_area(), which improves scalability when the vmap_node->busy.lock is contended. By doing so, the need to acquire the lock twice can also be eliminated to once. With the above change, tested on intel sapphire rapids platform(224 vcpu), a 4% performance improvement is gained on stress-ng/pthread(https://github.com/ColinIanKing/stress-ng), which is the stress test of thread creations. Link: https://lkml.kernel.org/r/20240307021440.64967-1-rulin.huang@intel.com Co-developed-by: "Chen, Tim C" <tim.c.chen@intel.com> Signed-off-by: "Chen, Tim C" <tim.c.chen@intel.com> Co-developed-by: "King, Colin" <colin.king@intel.com> Signed-off-by: "King, Colin" <colin.king@intel.com> Signed-off-by: rulinhuang <rulin.huang@intel.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Wangyang Guo <wangyang.guo@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-07 10:14:40 +08:00
* vstart and vend. If vm is passed in, the two will also be bound.
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
*/
static struct vmap_area *alloc_vmap_area(unsigned long size,
unsigned long align,
unsigned long vstart, unsigned long vend,
mm/vmalloc.c: add flags to mark vm_map_ram area Through vmalloc API, a virtual kernel area is reserved for physical address mapping. And vmap_area is used to track them, while vm_struct is allocated to associate with the vmap_area to store more information and passed out. However, area reserved via vm_map_ram() is an exception. It doesn't have vm_struct to associate with vmap_area. And we can't recognize the vmap_area with '->vm == NULL' as a vm_map_ram() area because the normal freeing path will set va->vm = NULL before unmapping, please see function remove_vm_area(). Meanwhile, there are two kinds of handling for vm_map_ram area. One is the whole vmap_area being reserved and mapped at one time through vm_map_area() interface; the other is the whole vmap_area with VMAP_BLOCK_SIZE size being reserved, while mapped into split regions with smaller size via vb_alloc(). To mark the area reserved through vm_map_ram(), add flags field into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, while bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-3-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:15 +08:00
int node, gfp_t gfp_mask,
unsigned long va_flags, struct vm_struct *vm)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn;
struct vmap_area *va;
unsigned long freed;
unsigned long addr;
unsigned int vn_id;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
int purged = 0;
int ret;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (unlikely(!size || offset_in_page(size) || !is_power_of_2(align)))
return ERR_PTR(-EINVAL);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (unlikely(!vmap_initialized))
return ERR_PTR(-EBUSY);
might_sleep();
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*
* If a VA is obtained from a global heap(if it fails here)
* it is anyway marked with this "vn_id" so it is returned
* to this pool's node later. Such way gives a possibility
* to populate pools based on users demand.
*
* On success a ready to go VA is returned.
*/
va = node_alloc(size, align, vstart, vend, &addr, &vn_id);
if (!va) {
gfp_mask = gfp_mask & GFP_RECLAIM_MASK;
va = kmem_cache_alloc_node(vmap_area_cachep, gfp_mask, node);
if (unlikely(!va))
return ERR_PTR(-ENOMEM);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*
* Only scan the relevant parts containing pointers to other objects
* to avoid false negatives.
*/
kmemleak_scan_area(&va->rb_node, SIZE_MAX, gfp_mask);
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
retry:
if (addr == vend) {
preload_this_cpu_lock(&free_vmap_area_lock, gfp_mask, node);
addr = __alloc_vmap_area(&free_vmap_area_root, &free_vmap_area_list,
size, align, vstart, vend);
spin_unlock(&free_vmap_area_lock);
}
mm: vmap area cache Provide a free area cache for the vmalloc virtual address allocator, based on the algorithm used by the user virtual memory allocator. This reduces the number of rbtree operations and linear traversals over the vmap extents in order to find a free area, by starting off at the last point that a free area was found. The free area cache is reset if areas are freed behind it, or if we are searching for a smaller area or alignment than last time. So allocation patterns are not changed (verified by corner-case and random test cases in userspace testing). This solves a regression caused by lazy vunmap TLB purging introduced in db64fe02 (mm: rewrite vmap layer). That patch will leave extents in the vmap allocator after they are vunmapped, and until a significant number accumulate that can be flushed in a single batch. So in a workload that vmalloc/vfree frequently, a chain of extents will build up from VMALLOC_START address, which have to be iterated over each time (giving an O(n) type of behaviour). After this patch, the search will start from where it left off, giving closer to an amortized O(1). This is verified to solve regressions reported Steven in GFS2, and Avi in KVM. Hugh's update: : I tried out the recent mmotm, and on one machine was fortunate to hit : the BUG_ON(first->va_start < addr) which seems to have been stalling : your vmap area cache patch ever since May. : I can get you addresses etc, I did dump a few out; but once I stared : at them, it was easier just to look at the code: and I cannot see how : you would be so sure that first->va_start < addr, once you've done : that addr = ALIGN(max(...), align) above, if align is over 0x1000 : (align was 0x8000 or 0x4000 in the cases I hit: ioremaps like Steve). : I originally got around it by just changing the : if (first->va_start < addr) { : to : while (first->va_start < addr) { : without thinking about it any further; but that seemed unsatisfactory, : why would we want to loop here when we've got another very similar : loop just below it? : I am never going to admit how long I've spent trying to grasp your : "while (n)" rbtree loop just above this, the one with the peculiar : if (!first && tmp->va_start < addr + size) : in. That's unfamiliar to me, I'm guessing it's designed to save a : subsequent rb_next() in a few circumstances (at risk of then setting : a wrong cached_hole_size?); but they did appear few to me, and I didn't : feel I could sign off something with that in when I don't grasp it, : and it seems responsible for extra code and mistaken BUG_ON below it. : I've reverted to the familiar rbtree loop that find_vma() does (but : with va_end >= addr as you had, to respect the additional guard page): : and then (given that cached_hole_size starts out 0) I don't see the : need for any complications below it. If you do want to keep that loop : as you had it, please add a comment to explain what it's trying to do, : and where addr is relative to first when you emerge from it. : Aren't your tests "size <= cached_hole_size" and : "addr + size > first->va_start" forgetting the guard page we want : before the next area? I've changed those. : I have not changed your many "addr + size - 1 < addr" overflow tests, : but have since come to wonder, shouldn't they be "addr + size < addr" : tests - won't the vend checks go wrong if addr + size is 0? : I have added a few comments - Wolfgang Wander's 2.6.13 description of : 1363c3cd8603a913a27e2995dccbd70d5312d8e6 Avoiding mmap fragmentation : helped me a lot, perhaps a pointer to that would be good too. And I found : it easier to understand when I renamed cached_start slightly and moved the : overflow label down. : This patch would go after your mm-vmap-area-cache.patch in mmotm. : Trivially, nobody is going to get that BUG_ON with this patch, and it : appears to work fine on my machines; but I have not given it anything like : the testing you did on your original, and may have broken all the : performance you were aiming for. Please take a look and test it out : integrate with yours if you're satisfied - thanks. [akpm@linux-foundation.org: add locking comment] Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reported-and-tested-by: Steven Whitehouse <swhiteho@redhat.com> Reported-and-tested-by: Avi Kivity <avi@redhat.com> Tested-by: "Barry J. Marson" <bmarson@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:30:36 +08:00
trace_alloc_vmap_area(addr, size, align, vstart, vend, addr == vend);
/*
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* If an allocation fails, the "vend" address is
* returned. Therefore trigger the overflow path.
*/
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (unlikely(addr == vend))
mm: vmap area cache Provide a free area cache for the vmalloc virtual address allocator, based on the algorithm used by the user virtual memory allocator. This reduces the number of rbtree operations and linear traversals over the vmap extents in order to find a free area, by starting off at the last point that a free area was found. The free area cache is reset if areas are freed behind it, or if we are searching for a smaller area or alignment than last time. So allocation patterns are not changed (verified by corner-case and random test cases in userspace testing). This solves a regression caused by lazy vunmap TLB purging introduced in db64fe02 (mm: rewrite vmap layer). That patch will leave extents in the vmap allocator after they are vunmapped, and until a significant number accumulate that can be flushed in a single batch. So in a workload that vmalloc/vfree frequently, a chain of extents will build up from VMALLOC_START address, which have to be iterated over each time (giving an O(n) type of behaviour). After this patch, the search will start from where it left off, giving closer to an amortized O(1). This is verified to solve regressions reported Steven in GFS2, and Avi in KVM. Hugh's update: : I tried out the recent mmotm, and on one machine was fortunate to hit : the BUG_ON(first->va_start < addr) which seems to have been stalling : your vmap area cache patch ever since May. : I can get you addresses etc, I did dump a few out; but once I stared : at them, it was easier just to look at the code: and I cannot see how : you would be so sure that first->va_start < addr, once you've done : that addr = ALIGN(max(...), align) above, if align is over 0x1000 : (align was 0x8000 or 0x4000 in the cases I hit: ioremaps like Steve). : I originally got around it by just changing the : if (first->va_start < addr) { : to : while (first->va_start < addr) { : without thinking about it any further; but that seemed unsatisfactory, : why would we want to loop here when we've got another very similar : loop just below it? : I am never going to admit how long I've spent trying to grasp your : "while (n)" rbtree loop just above this, the one with the peculiar : if (!first && tmp->va_start < addr + size) : in. That's unfamiliar to me, I'm guessing it's designed to save a : subsequent rb_next() in a few circumstances (at risk of then setting : a wrong cached_hole_size?); but they did appear few to me, and I didn't : feel I could sign off something with that in when I don't grasp it, : and it seems responsible for extra code and mistaken BUG_ON below it. : I've reverted to the familiar rbtree loop that find_vma() does (but : with va_end >= addr as you had, to respect the additional guard page): : and then (given that cached_hole_size starts out 0) I don't see the : need for any complications below it. If you do want to keep that loop : as you had it, please add a comment to explain what it's trying to do, : and where addr is relative to first when you emerge from it. : Aren't your tests "size <= cached_hole_size" and : "addr + size > first->va_start" forgetting the guard page we want : before the next area? I've changed those. : I have not changed your many "addr + size - 1 < addr" overflow tests, : but have since come to wonder, shouldn't they be "addr + size < addr" : tests - won't the vend checks go wrong if addr + size is 0? : I have added a few comments - Wolfgang Wander's 2.6.13 description of : 1363c3cd8603a913a27e2995dccbd70d5312d8e6 Avoiding mmap fragmentation : helped me a lot, perhaps a pointer to that would be good too. And I found : it easier to understand when I renamed cached_start slightly and moved the : overflow label down. : This patch would go after your mm-vmap-area-cache.patch in mmotm. : Trivially, nobody is going to get that BUG_ON with this patch, and it : appears to work fine on my machines; but I have not given it anything like : the testing you did on your original, and may have broken all the : performance you were aiming for. Please take a look and test it out : integrate with yours if you're satisfied - thanks. [akpm@linux-foundation.org: add locking comment] Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reported-and-tested-by: Steven Whitehouse <swhiteho@redhat.com> Reported-and-tested-by: Avi Kivity <avi@redhat.com> Tested-by: "Barry J. Marson" <bmarson@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:30:36 +08:00
goto overflow;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
va->va_start = addr;
va->va_end = addr + size;
va->vm = NULL;
va->flags = (va_flags | vn_id);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (vm) {
vm->addr = (void *)va->va_start;
vm->size = va->va_end - va->va_start;
va->vm = vm;
}
mm/vmalloc: eliminated the lock contention from twice to once When allocating a new memory area where the mapping address range is known, it is observed that the vmap_node->busy.lock is acquired twice. The first acquisition occurs in the alloc_vmap_area() function when inserting the vm area into the vm mapping red-black tree. The second acquisition occurs in the setup_vmalloc_vm() function when updating the properties of the vm, such as flags and address, etc. Combine these two operations together in alloc_vmap_area(), which improves scalability when the vmap_node->busy.lock is contended. By doing so, the need to acquire the lock twice can also be eliminated to once. With the above change, tested on intel sapphire rapids platform(224 vcpu), a 4% performance improvement is gained on stress-ng/pthread(https://github.com/ColinIanKing/stress-ng), which is the stress test of thread creations. Link: https://lkml.kernel.org/r/20240307021440.64967-1-rulin.huang@intel.com Co-developed-by: "Chen, Tim C" <tim.c.chen@intel.com> Signed-off-by: "Chen, Tim C" <tim.c.chen@intel.com> Co-developed-by: "King, Colin" <colin.king@intel.com> Signed-off-by: "King, Colin" <colin.king@intel.com> Signed-off-by: rulinhuang <rulin.huang@intel.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Wangyang Guo <wangyang.guo@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-07 10:14:40 +08:00
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
vn = addr_to_node(va->va_start);
spin_lock(&vn->busy.lock);
insert_vmap_area(va, &vn->busy.root, &vn->busy.head);
spin_unlock(&vn->busy.lock);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
BUG_ON(!IS_ALIGNED(va->va_start, align));
mm: vmap area cache Provide a free area cache for the vmalloc virtual address allocator, based on the algorithm used by the user virtual memory allocator. This reduces the number of rbtree operations and linear traversals over the vmap extents in order to find a free area, by starting off at the last point that a free area was found. The free area cache is reset if areas are freed behind it, or if we are searching for a smaller area or alignment than last time. So allocation patterns are not changed (verified by corner-case and random test cases in userspace testing). This solves a regression caused by lazy vunmap TLB purging introduced in db64fe02 (mm: rewrite vmap layer). That patch will leave extents in the vmap allocator after they are vunmapped, and until a significant number accumulate that can be flushed in a single batch. So in a workload that vmalloc/vfree frequently, a chain of extents will build up from VMALLOC_START address, which have to be iterated over each time (giving an O(n) type of behaviour). After this patch, the search will start from where it left off, giving closer to an amortized O(1). This is verified to solve regressions reported Steven in GFS2, and Avi in KVM. Hugh's update: : I tried out the recent mmotm, and on one machine was fortunate to hit : the BUG_ON(first->va_start < addr) which seems to have been stalling : your vmap area cache patch ever since May. : I can get you addresses etc, I did dump a few out; but once I stared : at them, it was easier just to look at the code: and I cannot see how : you would be so sure that first->va_start < addr, once you've done : that addr = ALIGN(max(...), align) above, if align is over 0x1000 : (align was 0x8000 or 0x4000 in the cases I hit: ioremaps like Steve). : I originally got around it by just changing the : if (first->va_start < addr) { : to : while (first->va_start < addr) { : without thinking about it any further; but that seemed unsatisfactory, : why would we want to loop here when we've got another very similar : loop just below it? : I am never going to admit how long I've spent trying to grasp your : "while (n)" rbtree loop just above this, the one with the peculiar : if (!first && tmp->va_start < addr + size) : in. That's unfamiliar to me, I'm guessing it's designed to save a : subsequent rb_next() in a few circumstances (at risk of then setting : a wrong cached_hole_size?); but they did appear few to me, and I didn't : feel I could sign off something with that in when I don't grasp it, : and it seems responsible for extra code and mistaken BUG_ON below it. : I've reverted to the familiar rbtree loop that find_vma() does (but : with va_end >= addr as you had, to respect the additional guard page): : and then (given that cached_hole_size starts out 0) I don't see the : need for any complications below it. If you do want to keep that loop : as you had it, please add a comment to explain what it's trying to do, : and where addr is relative to first when you emerge from it. : Aren't your tests "size <= cached_hole_size" and : "addr + size > first->va_start" forgetting the guard page we want : before the next area? I've changed those. : I have not changed your many "addr + size - 1 < addr" overflow tests, : but have since come to wonder, shouldn't they be "addr + size < addr" : tests - won't the vend checks go wrong if addr + size is 0? : I have added a few comments - Wolfgang Wander's 2.6.13 description of : 1363c3cd8603a913a27e2995dccbd70d5312d8e6 Avoiding mmap fragmentation : helped me a lot, perhaps a pointer to that would be good too. And I found : it easier to understand when I renamed cached_start slightly and moved the : overflow label down. : This patch would go after your mm-vmap-area-cache.patch in mmotm. : Trivially, nobody is going to get that BUG_ON with this patch, and it : appears to work fine on my machines; but I have not given it anything like : the testing you did on your original, and may have broken all the : performance you were aiming for. Please take a look and test it out : integrate with yours if you're satisfied - thanks. [akpm@linux-foundation.org: add locking comment] Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reported-and-tested-by: Steven Whitehouse <swhiteho@redhat.com> Reported-and-tested-by: Avi Kivity <avi@redhat.com> Tested-by: "Barry J. Marson" <bmarson@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:30:36 +08:00
BUG_ON(va->va_start < vstart);
BUG_ON(va->va_end > vend);
ret = kasan_populate_vmalloc(addr, size);
if (ret) {
free_vmap_area(va);
return ERR_PTR(ret);
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
return va;
mm: vmap area cache Provide a free area cache for the vmalloc virtual address allocator, based on the algorithm used by the user virtual memory allocator. This reduces the number of rbtree operations and linear traversals over the vmap extents in order to find a free area, by starting off at the last point that a free area was found. The free area cache is reset if areas are freed behind it, or if we are searching for a smaller area or alignment than last time. So allocation patterns are not changed (verified by corner-case and random test cases in userspace testing). This solves a regression caused by lazy vunmap TLB purging introduced in db64fe02 (mm: rewrite vmap layer). That patch will leave extents in the vmap allocator after they are vunmapped, and until a significant number accumulate that can be flushed in a single batch. So in a workload that vmalloc/vfree frequently, a chain of extents will build up from VMALLOC_START address, which have to be iterated over each time (giving an O(n) type of behaviour). After this patch, the search will start from where it left off, giving closer to an amortized O(1). This is verified to solve regressions reported Steven in GFS2, and Avi in KVM. Hugh's update: : I tried out the recent mmotm, and on one machine was fortunate to hit : the BUG_ON(first->va_start < addr) which seems to have been stalling : your vmap area cache patch ever since May. : I can get you addresses etc, I did dump a few out; but once I stared : at them, it was easier just to look at the code: and I cannot see how : you would be so sure that first->va_start < addr, once you've done : that addr = ALIGN(max(...), align) above, if align is over 0x1000 : (align was 0x8000 or 0x4000 in the cases I hit: ioremaps like Steve). : I originally got around it by just changing the : if (first->va_start < addr) { : to : while (first->va_start < addr) { : without thinking about it any further; but that seemed unsatisfactory, : why would we want to loop here when we've got another very similar : loop just below it? : I am never going to admit how long I've spent trying to grasp your : "while (n)" rbtree loop just above this, the one with the peculiar : if (!first && tmp->va_start < addr + size) : in. That's unfamiliar to me, I'm guessing it's designed to save a : subsequent rb_next() in a few circumstances (at risk of then setting : a wrong cached_hole_size?); but they did appear few to me, and I didn't : feel I could sign off something with that in when I don't grasp it, : and it seems responsible for extra code and mistaken BUG_ON below it. : I've reverted to the familiar rbtree loop that find_vma() does (but : with va_end >= addr as you had, to respect the additional guard page): : and then (given that cached_hole_size starts out 0) I don't see the : need for any complications below it. If you do want to keep that loop : as you had it, please add a comment to explain what it's trying to do, : and where addr is relative to first when you emerge from it. : Aren't your tests "size <= cached_hole_size" and : "addr + size > first->va_start" forgetting the guard page we want : before the next area? I've changed those. : I have not changed your many "addr + size - 1 < addr" overflow tests, : but have since come to wonder, shouldn't they be "addr + size < addr" : tests - won't the vend checks go wrong if addr + size is 0? : I have added a few comments - Wolfgang Wander's 2.6.13 description of : 1363c3cd8603a913a27e2995dccbd70d5312d8e6 Avoiding mmap fragmentation : helped me a lot, perhaps a pointer to that would be good too. And I found : it easier to understand when I renamed cached_start slightly and moved the : overflow label down. : This patch would go after your mm-vmap-area-cache.patch in mmotm. : Trivially, nobody is going to get that BUG_ON with this patch, and it : appears to work fine on my machines; but I have not given it anything like : the testing you did on your original, and may have broken all the : performance you were aiming for. Please take a look and test it out : integrate with yours if you're satisfied - thanks. [akpm@linux-foundation.org: add locking comment] Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reported-and-tested-by: Steven Whitehouse <swhiteho@redhat.com> Reported-and-tested-by: Avi Kivity <avi@redhat.com> Tested-by: "Barry J. Marson" <bmarson@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:30:36 +08:00
overflow:
if (!purged) {
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
reclaim_and_purge_vmap_areas();
mm: vmap area cache Provide a free area cache for the vmalloc virtual address allocator, based on the algorithm used by the user virtual memory allocator. This reduces the number of rbtree operations and linear traversals over the vmap extents in order to find a free area, by starting off at the last point that a free area was found. The free area cache is reset if areas are freed behind it, or if we are searching for a smaller area or alignment than last time. So allocation patterns are not changed (verified by corner-case and random test cases in userspace testing). This solves a regression caused by lazy vunmap TLB purging introduced in db64fe02 (mm: rewrite vmap layer). That patch will leave extents in the vmap allocator after they are vunmapped, and until a significant number accumulate that can be flushed in a single batch. So in a workload that vmalloc/vfree frequently, a chain of extents will build up from VMALLOC_START address, which have to be iterated over each time (giving an O(n) type of behaviour). After this patch, the search will start from where it left off, giving closer to an amortized O(1). This is verified to solve regressions reported Steven in GFS2, and Avi in KVM. Hugh's update: : I tried out the recent mmotm, and on one machine was fortunate to hit : the BUG_ON(first->va_start < addr) which seems to have been stalling : your vmap area cache patch ever since May. : I can get you addresses etc, I did dump a few out; but once I stared : at them, it was easier just to look at the code: and I cannot see how : you would be so sure that first->va_start < addr, once you've done : that addr = ALIGN(max(...), align) above, if align is over 0x1000 : (align was 0x8000 or 0x4000 in the cases I hit: ioremaps like Steve). : I originally got around it by just changing the : if (first->va_start < addr) { : to : while (first->va_start < addr) { : without thinking about it any further; but that seemed unsatisfactory, : why would we want to loop here when we've got another very similar : loop just below it? : I am never going to admit how long I've spent trying to grasp your : "while (n)" rbtree loop just above this, the one with the peculiar : if (!first && tmp->va_start < addr + size) : in. That's unfamiliar to me, I'm guessing it's designed to save a : subsequent rb_next() in a few circumstances (at risk of then setting : a wrong cached_hole_size?); but they did appear few to me, and I didn't : feel I could sign off something with that in when I don't grasp it, : and it seems responsible for extra code and mistaken BUG_ON below it. : I've reverted to the familiar rbtree loop that find_vma() does (but : with va_end >= addr as you had, to respect the additional guard page): : and then (given that cached_hole_size starts out 0) I don't see the : need for any complications below it. If you do want to keep that loop : as you had it, please add a comment to explain what it's trying to do, : and where addr is relative to first when you emerge from it. : Aren't your tests "size <= cached_hole_size" and : "addr + size > first->va_start" forgetting the guard page we want : before the next area? I've changed those. : I have not changed your many "addr + size - 1 < addr" overflow tests, : but have since come to wonder, shouldn't they be "addr + size < addr" : tests - won't the vend checks go wrong if addr + size is 0? : I have added a few comments - Wolfgang Wander's 2.6.13 description of : 1363c3cd8603a913a27e2995dccbd70d5312d8e6 Avoiding mmap fragmentation : helped me a lot, perhaps a pointer to that would be good too. And I found : it easier to understand when I renamed cached_start slightly and moved the : overflow label down. : This patch would go after your mm-vmap-area-cache.patch in mmotm. : Trivially, nobody is going to get that BUG_ON with this patch, and it : appears to work fine on my machines; but I have not given it anything like : the testing you did on your original, and may have broken all the : performance you were aiming for. Please take a look and test it out : integrate with yours if you're satisfied - thanks. [akpm@linux-foundation.org: add locking comment] Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reported-and-tested-by: Steven Whitehouse <swhiteho@redhat.com> Reported-and-tested-by: Avi Kivity <avi@redhat.com> Tested-by: "Barry J. Marson" <bmarson@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:30:36 +08:00
purged = 1;
goto retry;
}
freed = 0;
blocking_notifier_call_chain(&vmap_notify_list, 0, &freed);
if (freed > 0) {
purged = 0;
goto retry;
}
if (!(gfp_mask & __GFP_NOWARN) && printk_ratelimit())
pr_warn("vmap allocation for size %lu failed: use vmalloc=<size> to increase size\n",
size);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
kmem_cache_free(vmap_area_cachep, va);
mm: vmap area cache Provide a free area cache for the vmalloc virtual address allocator, based on the algorithm used by the user virtual memory allocator. This reduces the number of rbtree operations and linear traversals over the vmap extents in order to find a free area, by starting off at the last point that a free area was found. The free area cache is reset if areas are freed behind it, or if we are searching for a smaller area or alignment than last time. So allocation patterns are not changed (verified by corner-case and random test cases in userspace testing). This solves a regression caused by lazy vunmap TLB purging introduced in db64fe02 (mm: rewrite vmap layer). That patch will leave extents in the vmap allocator after they are vunmapped, and until a significant number accumulate that can be flushed in a single batch. So in a workload that vmalloc/vfree frequently, a chain of extents will build up from VMALLOC_START address, which have to be iterated over each time (giving an O(n) type of behaviour). After this patch, the search will start from where it left off, giving closer to an amortized O(1). This is verified to solve regressions reported Steven in GFS2, and Avi in KVM. Hugh's update: : I tried out the recent mmotm, and on one machine was fortunate to hit : the BUG_ON(first->va_start < addr) which seems to have been stalling : your vmap area cache patch ever since May. : I can get you addresses etc, I did dump a few out; but once I stared : at them, it was easier just to look at the code: and I cannot see how : you would be so sure that first->va_start < addr, once you've done : that addr = ALIGN(max(...), align) above, if align is over 0x1000 : (align was 0x8000 or 0x4000 in the cases I hit: ioremaps like Steve). : I originally got around it by just changing the : if (first->va_start < addr) { : to : while (first->va_start < addr) { : without thinking about it any further; but that seemed unsatisfactory, : why would we want to loop here when we've got another very similar : loop just below it? : I am never going to admit how long I've spent trying to grasp your : "while (n)" rbtree loop just above this, the one with the peculiar : if (!first && tmp->va_start < addr + size) : in. That's unfamiliar to me, I'm guessing it's designed to save a : subsequent rb_next() in a few circumstances (at risk of then setting : a wrong cached_hole_size?); but they did appear few to me, and I didn't : feel I could sign off something with that in when I don't grasp it, : and it seems responsible for extra code and mistaken BUG_ON below it. : I've reverted to the familiar rbtree loop that find_vma() does (but : with va_end >= addr as you had, to respect the additional guard page): : and then (given that cached_hole_size starts out 0) I don't see the : need for any complications below it. If you do want to keep that loop : as you had it, please add a comment to explain what it's trying to do, : and where addr is relative to first when you emerge from it. : Aren't your tests "size <= cached_hole_size" and : "addr + size > first->va_start" forgetting the guard page we want : before the next area? I've changed those. : I have not changed your many "addr + size - 1 < addr" overflow tests, : but have since come to wonder, shouldn't they be "addr + size < addr" : tests - won't the vend checks go wrong if addr + size is 0? : I have added a few comments - Wolfgang Wander's 2.6.13 description of : 1363c3cd8603a913a27e2995dccbd70d5312d8e6 Avoiding mmap fragmentation : helped me a lot, perhaps a pointer to that would be good too. And I found : it easier to understand when I renamed cached_start slightly and moved the : overflow label down. : This patch would go after your mm-vmap-area-cache.patch in mmotm. : Trivially, nobody is going to get that BUG_ON with this patch, and it : appears to work fine on my machines; but I have not given it anything like : the testing you did on your original, and may have broken all the : performance you were aiming for. Please take a look and test it out : integrate with yours if you're satisfied - thanks. [akpm@linux-foundation.org: add locking comment] Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reported-and-tested-by: Steven Whitehouse <swhiteho@redhat.com> Reported-and-tested-by: Avi Kivity <avi@redhat.com> Tested-by: "Barry J. Marson" <bmarson@redhat.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-23 07:30:36 +08:00
return ERR_PTR(-EBUSY);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
int register_vmap_purge_notifier(struct notifier_block *nb)
{
return blocking_notifier_chain_register(&vmap_notify_list, nb);
}
EXPORT_SYMBOL_GPL(register_vmap_purge_notifier);
int unregister_vmap_purge_notifier(struct notifier_block *nb)
{
return blocking_notifier_chain_unregister(&vmap_notify_list, nb);
}
EXPORT_SYMBOL_GPL(unregister_vmap_purge_notifier);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*
* lazy_max_pages is the maximum amount of virtual address space we gather up
* before attempting to purge with a TLB flush.
*
* There is a tradeoff here: a larger number will cover more kernel page tables
* and take slightly longer to purge, but it will linearly reduce the number of
* global TLB flushes that must be performed. It would seem natural to scale
* this number up linearly with the number of CPUs (because vmapping activity
* could also scale linearly with the number of CPUs), however it is likely
* that in practice, workloads might be constrained in other ways that mean
* vmap activity will not scale linearly with CPUs. Also, I want to be
* conservative and not introduce a big latency on huge systems, so go with
* a less aggressive log scale. It will still be an improvement over the old
* code, and it will be simple to change the scale factor if we find that it
* becomes a problem on bigger systems.
*/
static unsigned long lazy_max_pages(void)
{
unsigned int log;
log = fls(num_online_cpus());
return log * (32UL * 1024 * 1024 / PAGE_SIZE);
}
static atomic_long_t vmap_lazy_nr = ATOMIC_LONG_INIT(0);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*
* Serialize vmap purging. There is no actual critical section protected
* by this lock, but we want to avoid concurrent calls for performance
* reasons and to make the pcpu_get_vm_areas more deterministic.
*/
static DEFINE_MUTEX(vmap_purge_lock);
/* for per-CPU blocks */
static void purge_fragmented_blocks_allcpus(void);
static cpumask_t purge_nodes;
static void
reclaim_list_global(struct list_head *head)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
struct vmap_area *va, *n;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (list_empty(head))
return;
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
spin_lock(&free_vmap_area_lock);
list_for_each_entry_safe(va, n, head, list)
merge_or_add_vmap_area_augment(va,
&free_vmap_area_root, &free_vmap_area_list);
spin_unlock(&free_vmap_area_lock);
}
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
static void
decay_va_pool_node(struct vmap_node *vn, bool full_decay)
{
struct vmap_area *va, *nva;
struct list_head decay_list;
struct rb_root decay_root;
unsigned long n_decay;
int i;
mm/vmalloc.c: add priority threshold to __purge_vmap_area_lazy() Commit 763b218ddfaf ("mm: add preempt points into __purge_vmap_area_lazy()") introduced some preempt points, one of those is making an allocation more prioritized over lazy free of vmap areas. Prioritizing an allocation over freeing does not work well all the time, i.e. it should be rather a compromise. 1) Number of lazy pages directly influences the busy list length thus on operations like: allocation, lookup, unmap, remove, etc. 2) Under heavy stress of vmalloc subsystem I run into a situation when memory usage gets increased hitting out_of_memory -> panic state due to completely blocking of logic that frees vmap areas in the __purge_vmap_area_lazy() function. Establish a threshold passing which the freeing is prioritized back over allocation creating a balance between each other. Using vmalloc test driver in "stress mode", i.e. When all available test cases are run simultaneously on all online CPUs applying a pressure on the vmalloc subsystem, my HiKey 960 board runs out of memory due to the fact that __purge_vmap_area_lazy() logic simply is not able to free pages in time. How I run it: 1) You should build your kernel with CONFIG_TEST_VMALLOC=m 2) ./tools/testing/selftests/vm/test_vmalloc.sh stress During this test "vmap_lazy_nr" pages will go far beyond acceptable lazy_max_pages() threshold, that will lead to enormous busy list size and other problems including allocation time and so on. Link: http://lkml.kernel.org/r/20190124115648.9433-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Cc: Joel Fernandes <joel@joelfernandes.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-15 06:41:22 +08:00
decay_root = RB_ROOT;
INIT_LIST_HEAD(&decay_list);
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
for (i = 0; i < MAX_VA_SIZE_PAGES; i++) {
struct list_head tmp_list;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (list_empty(&vn->pool[i].head))
continue;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
INIT_LIST_HEAD(&tmp_list);
/* Detach the pool, so no-one can access it. */
spin_lock(&vn->pool_lock);
list_replace_init(&vn->pool[i].head, &tmp_list);
spin_unlock(&vn->pool_lock);
if (full_decay)
WRITE_ONCE(vn->pool[i].len, 0);
/* Decay a pool by ~25% out of left objects. */
n_decay = vn->pool[i].len >> 2;
list_for_each_entry_safe(va, nva, &tmp_list, list) {
list_del_init(&va->list);
merge_or_add_vmap_area(va, &decay_root, &decay_list);
if (!full_decay) {
WRITE_ONCE(vn->pool[i].len, vn->pool[i].len - 1);
if (!--n_decay)
break;
}
}
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
/*
* Attach the pool back if it has been partly decayed.
* Please note, it is supposed that nobody(other contexts)
* can populate the pool therefore a simple list replace
* operation takes place here.
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
*/
if (!full_decay && !list_empty(&tmp_list)) {
spin_lock(&vn->pool_lock);
list_replace_init(&tmp_list, &vn->pool[i].head);
spin_unlock(&vn->pool_lock);
}
}
kasan: support backing vmalloc space with real shadow memory Patch series "kasan: support backing vmalloc space with real shadow memory", v11. Currently, vmalloc space is backed by the early shadow page. This means that kasan is incompatible with VMAP_STACK. This series provides a mechanism to back vmalloc space with real, dynamically allocated memory. I have only wired up x86, because that's the only currently supported arch I can work with easily, but it's very easy to wire up other architectures, and it appears that there is some work-in-progress code to do this on arm64 and s390. This has been discussed before in the context of VMAP_STACK: - https://bugzilla.kernel.org/show_bug.cgi?id=202009 - https://lkml.org/lkml/2018/7/22/198 - https://lkml.org/lkml/2019/7/19/822 In terms of implementation details: Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=1) This is unfortunate but given that this is a debug feature only, not the end of the world. The benchmarks are also a stress-test for the vmalloc subsystem: they're not indicative of an overall 2x slowdown! This patch (of 4): Hook into vmalloc and vmap, and dynamically allocate real shadow memory to back the mappings. Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. To avoid the difficulties around swapping mappings around, this code expects that the part of the shadow region that covers the vmalloc space will not be covered by the early shadow page, but will be left unmapped. This will require changes in arch-specific code. This allows KASAN with VMAP_STACK, and may be helpful for architectures that do not have a separate module space (e.g. powerpc64, which I am currently working on). It also allows relaxing the module alignment back to PAGE_SIZE. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=3D1) This is unfortunate but given that this is a debug feature only, not the end of the world. The full benchmark results are: Performance No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 662004 11404956 17.23 19144610 28.92 1.68 full_fit_alloc_test 710950 12029752 16.92 13184651 18.55 1.10 long_busy_list_alloc_test 9431875 43990172 4.66 82970178 8.80 1.89 random_size_alloc_test 5033626 23061762 4.58 47158834 9.37 2.04 fix_align_alloc_test 1252514 15276910 12.20 31266116 24.96 2.05 random_size_align_alloc_te 1648501 14578321 8.84 25560052 15.51 1.75 align_shift_alloc_test 147 830 5.65 5692 38.72 6.86 pcpu_alloc_test 80732 125520 1.55 140864 1.74 1.12 Total Cycles 119240774314 763211341128 6.40 1390338696894 11.66 1.82 Sequential, 2 cpus No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 1423150 14276550 10.03 27733022 19.49 1.94 full_fit_alloc_test 1754219 14722640 8.39 15030786 8.57 1.02 long_busy_list_alloc_test 11451858 52154973 4.55 107016027 9.34 2.05 random_size_alloc_test 5989020 26735276 4.46 68885923 11.50 2.58 fix_align_alloc_test 2050976 20166900 9.83 50491675 24.62 2.50 random_size_align_alloc_te 2858229 17971700 6.29 38730225 13.55 2.16 align_shift_alloc_test 405 6428 15.87 26253 64.82 4.08 pcpu_alloc_test 127183 151464 1.19 216263 1.70 1.43 Total Cycles 54181269392 308723699764 5.70 650772566394 12.01 2.11 fix_size_alloc_test 1420404 14289308 10.06 27790035 19.56 1.94 full_fit_alloc_test 1736145 14806234 8.53 15274301 8.80 1.03 long_busy_list_alloc_test 11404638 52270785 4.58 107550254 9.43 2.06 random_size_alloc_test 6017006 26650625 4.43 68696127 11.42 2.58 fix_align_alloc_test 2045504 20280985 9.91 50414862 24.65 2.49 random_size_align_alloc_te 2845338 17931018 6.30 38510276 13.53 2.15 align_shift_alloc_test 472 3760 7.97 9656 20.46 2.57 pcpu_alloc_test 118643 132732 1.12 146504 1.23 1.10 Total Cycles 54040011688 309102805492 5.72 651325675652 12.05 2.11 [dja@axtens.net: fixups] Link: http://lkml.kernel.org/r/20191120052719.7201-1-dja@axtens.net Link: https://bugzilla.kernel.org/show_bug.cgi?id=3D202009 Link: http://lkml.kernel.org/r/20191031093909.9228-2-dja@axtens.net Signed-off-by: Mark Rutland <mark.rutland@arm.com> [shadow rework] Signed-off-by: Daniel Axtens <dja@axtens.net> Co-developed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Vasily Gorbik <gor@linux.ibm.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:50 +08:00
reclaim_list_global(&decay_list);
}
static void purge_vmap_node(struct work_struct *work)
{
struct vmap_node *vn = container_of(work,
struct vmap_node, purge_work);
struct vmap_area *va, *n_va;
LIST_HEAD(local_list);
vn->nr_purged = 0;
list_for_each_entry_safe(va, n_va, &vn->purge_list, list) {
unsigned long nr = (va->va_end - va->va_start) >> PAGE_SHIFT;
kasan: support backing vmalloc space with real shadow memory Patch series "kasan: support backing vmalloc space with real shadow memory", v11. Currently, vmalloc space is backed by the early shadow page. This means that kasan is incompatible with VMAP_STACK. This series provides a mechanism to back vmalloc space with real, dynamically allocated memory. I have only wired up x86, because that's the only currently supported arch I can work with easily, but it's very easy to wire up other architectures, and it appears that there is some work-in-progress code to do this on arm64 and s390. This has been discussed before in the context of VMAP_STACK: - https://bugzilla.kernel.org/show_bug.cgi?id=202009 - https://lkml.org/lkml/2018/7/22/198 - https://lkml.org/lkml/2019/7/19/822 In terms of implementation details: Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=1) This is unfortunate but given that this is a debug feature only, not the end of the world. The benchmarks are also a stress-test for the vmalloc subsystem: they're not indicative of an overall 2x slowdown! This patch (of 4): Hook into vmalloc and vmap, and dynamically allocate real shadow memory to back the mappings. Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. To avoid the difficulties around swapping mappings around, this code expects that the part of the shadow region that covers the vmalloc space will not be covered by the early shadow page, but will be left unmapped. This will require changes in arch-specific code. This allows KASAN with VMAP_STACK, and may be helpful for architectures that do not have a separate module space (e.g. powerpc64, which I am currently working on). It also allows relaxing the module alignment back to PAGE_SIZE. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=3D1) This is unfortunate but given that this is a debug feature only, not the end of the world. The full benchmark results are: Performance No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 662004 11404956 17.23 19144610 28.92 1.68 full_fit_alloc_test 710950 12029752 16.92 13184651 18.55 1.10 long_busy_list_alloc_test 9431875 43990172 4.66 82970178 8.80 1.89 random_size_alloc_test 5033626 23061762 4.58 47158834 9.37 2.04 fix_align_alloc_test 1252514 15276910 12.20 31266116 24.96 2.05 random_size_align_alloc_te 1648501 14578321 8.84 25560052 15.51 1.75 align_shift_alloc_test 147 830 5.65 5692 38.72 6.86 pcpu_alloc_test 80732 125520 1.55 140864 1.74 1.12 Total Cycles 119240774314 763211341128 6.40 1390338696894 11.66 1.82 Sequential, 2 cpus No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 1423150 14276550 10.03 27733022 19.49 1.94 full_fit_alloc_test 1754219 14722640 8.39 15030786 8.57 1.02 long_busy_list_alloc_test 11451858 52154973 4.55 107016027 9.34 2.05 random_size_alloc_test 5989020 26735276 4.46 68885923 11.50 2.58 fix_align_alloc_test 2050976 20166900 9.83 50491675 24.62 2.50 random_size_align_alloc_te 2858229 17971700 6.29 38730225 13.55 2.16 align_shift_alloc_test 405 6428 15.87 26253 64.82 4.08 pcpu_alloc_test 127183 151464 1.19 216263 1.70 1.43 Total Cycles 54181269392 308723699764 5.70 650772566394 12.01 2.11 fix_size_alloc_test 1420404 14289308 10.06 27790035 19.56 1.94 full_fit_alloc_test 1736145 14806234 8.53 15274301 8.80 1.03 long_busy_list_alloc_test 11404638 52270785 4.58 107550254 9.43 2.06 random_size_alloc_test 6017006 26650625 4.43 68696127 11.42 2.58 fix_align_alloc_test 2045504 20280985 9.91 50414862 24.65 2.49 random_size_align_alloc_te 2845338 17931018 6.30 38510276 13.53 2.15 align_shift_alloc_test 472 3760 7.97 9656 20.46 2.57 pcpu_alloc_test 118643 132732 1.12 146504 1.23 1.10 Total Cycles 54040011688 309102805492 5.72 651325675652 12.05 2.11 [dja@axtens.net: fixups] Link: http://lkml.kernel.org/r/20191120052719.7201-1-dja@axtens.net Link: https://bugzilla.kernel.org/show_bug.cgi?id=3D202009 Link: http://lkml.kernel.org/r/20191031093909.9228-2-dja@axtens.net Signed-off-by: Mark Rutland <mark.rutland@arm.com> [shadow rework] Signed-off-by: Daniel Axtens <dja@axtens.net> Co-developed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Vasily Gorbik <gor@linux.ibm.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:50 +08:00
unsigned long orig_start = va->va_start;
unsigned long orig_end = va->va_end;
unsigned int vn_id = decode_vn_id(va->flags);
list_del_init(&va->list);
kasan: support backing vmalloc space with real shadow memory Patch series "kasan: support backing vmalloc space with real shadow memory", v11. Currently, vmalloc space is backed by the early shadow page. This means that kasan is incompatible with VMAP_STACK. This series provides a mechanism to back vmalloc space with real, dynamically allocated memory. I have only wired up x86, because that's the only currently supported arch I can work with easily, but it's very easy to wire up other architectures, and it appears that there is some work-in-progress code to do this on arm64 and s390. This has been discussed before in the context of VMAP_STACK: - https://bugzilla.kernel.org/show_bug.cgi?id=202009 - https://lkml.org/lkml/2018/7/22/198 - https://lkml.org/lkml/2019/7/19/822 In terms of implementation details: Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=1) This is unfortunate but given that this is a debug feature only, not the end of the world. The benchmarks are also a stress-test for the vmalloc subsystem: they're not indicative of an overall 2x slowdown! This patch (of 4): Hook into vmalloc and vmap, and dynamically allocate real shadow memory to back the mappings. Most mappings in vmalloc space are small, requiring less than a full page of shadow space. Allocating a full shadow page per mapping would therefore be wasteful. Furthermore, to ensure that different mappings use different shadow pages, mappings would have to be aligned to KASAN_SHADOW_SCALE_SIZE * PAGE_SIZE. Instead, share backing space across multiple mappings. Allocate a backing page when a mapping in vmalloc space uses a particular page of the shadow region. This page can be shared by other vmalloc mappings later on. We hook in to the vmap infrastructure to lazily clean up unused shadow memory. To avoid the difficulties around swapping mappings around, this code expects that the part of the shadow region that covers the vmalloc space will not be covered by the early shadow page, but will be left unmapped. This will require changes in arch-specific code. This allows KASAN with VMAP_STACK, and may be helpful for architectures that do not have a separate module space (e.g. powerpc64, which I am currently working on). It also allows relaxing the module alignment back to PAGE_SIZE. Testing with test_vmalloc.sh on an x86 VM with 2 vCPUs shows that: - Turning on KASAN, inline instrumentation, without vmalloc, introuduces a 4.1x-4.2x slowdown in vmalloc operations. - Turning this on introduces the following slowdowns over KASAN: * ~1.76x slower single-threaded (test_vmalloc.sh performance) * ~2.18x slower when both cpus are performing operations simultaneously (test_vmalloc.sh sequential_test_order=3D1) This is unfortunate but given that this is a debug feature only, not the end of the world. The full benchmark results are: Performance No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 662004 11404956 17.23 19144610 28.92 1.68 full_fit_alloc_test 710950 12029752 16.92 13184651 18.55 1.10 long_busy_list_alloc_test 9431875 43990172 4.66 82970178 8.80 1.89 random_size_alloc_test 5033626 23061762 4.58 47158834 9.37 2.04 fix_align_alloc_test 1252514 15276910 12.20 31266116 24.96 2.05 random_size_align_alloc_te 1648501 14578321 8.84 25560052 15.51 1.75 align_shift_alloc_test 147 830 5.65 5692 38.72 6.86 pcpu_alloc_test 80732 125520 1.55 140864 1.74 1.12 Total Cycles 119240774314 763211341128 6.40 1390338696894 11.66 1.82 Sequential, 2 cpus No KASAN KASAN original x baseline KASAN vmalloc x baseline x KASAN fix_size_alloc_test 1423150 14276550 10.03 27733022 19.49 1.94 full_fit_alloc_test 1754219 14722640 8.39 15030786 8.57 1.02 long_busy_list_alloc_test 11451858 52154973 4.55 107016027 9.34 2.05 random_size_alloc_test 5989020 26735276 4.46 68885923 11.50 2.58 fix_align_alloc_test 2050976 20166900 9.83 50491675 24.62 2.50 random_size_align_alloc_te 2858229 17971700 6.29 38730225 13.55 2.16 align_shift_alloc_test 405 6428 15.87 26253 64.82 4.08 pcpu_alloc_test 127183 151464 1.19 216263 1.70 1.43 Total Cycles 54181269392 308723699764 5.70 650772566394 12.01 2.11 fix_size_alloc_test 1420404 14289308 10.06 27790035 19.56 1.94 full_fit_alloc_test 1736145 14806234 8.53 15274301 8.80 1.03 long_busy_list_alloc_test 11404638 52270785 4.58 107550254 9.43 2.06 random_size_alloc_test 6017006 26650625 4.43 68696127 11.42 2.58 fix_align_alloc_test 2045504 20280985 9.91 50414862 24.65 2.49 random_size_align_alloc_te 2845338 17931018 6.30 38510276 13.53 2.15 align_shift_alloc_test 472 3760 7.97 9656 20.46 2.57 pcpu_alloc_test 118643 132732 1.12 146504 1.23 1.10 Total Cycles 54040011688 309102805492 5.72 651325675652 12.05 2.11 [dja@axtens.net: fixups] Link: http://lkml.kernel.org/r/20191120052719.7201-1-dja@axtens.net Link: https://bugzilla.kernel.org/show_bug.cgi?id=3D202009 Link: http://lkml.kernel.org/r/20191031093909.9228-2-dja@axtens.net Signed-off-by: Mark Rutland <mark.rutland@arm.com> [shadow rework] Signed-off-by: Daniel Axtens <dja@axtens.net> Co-developed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Vasily Gorbik <gor@linux.ibm.com> Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:50 +08:00
if (is_vmalloc_or_module_addr((void *)orig_start))
kasan_release_vmalloc(orig_start, orig_end,
va->va_start, va->va_end);
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
atomic_long_sub(nr, &vmap_lazy_nr);
vn->nr_purged++;
mm/vmalloc.c: add priority threshold to __purge_vmap_area_lazy() Commit 763b218ddfaf ("mm: add preempt points into __purge_vmap_area_lazy()") introduced some preempt points, one of those is making an allocation more prioritized over lazy free of vmap areas. Prioritizing an allocation over freeing does not work well all the time, i.e. it should be rather a compromise. 1) Number of lazy pages directly influences the busy list length thus on operations like: allocation, lookup, unmap, remove, etc. 2) Under heavy stress of vmalloc subsystem I run into a situation when memory usage gets increased hitting out_of_memory -> panic state due to completely blocking of logic that frees vmap areas in the __purge_vmap_area_lazy() function. Establish a threshold passing which the freeing is prioritized back over allocation creating a balance between each other. Using vmalloc test driver in "stress mode", i.e. When all available test cases are run simultaneously on all online CPUs applying a pressure on the vmalloc subsystem, my HiKey 960 board runs out of memory due to the fact that __purge_vmap_area_lazy() logic simply is not able to free pages in time. How I run it: 1) You should build your kernel with CONFIG_TEST_VMALLOC=m 2) ./tools/testing/selftests/vm/test_vmalloc.sh stress During this test "vmap_lazy_nr" pages will go far beyond acceptable lazy_max_pages() threshold, that will lead to enormous busy list size and other problems including allocation time and so on. Link: http://lkml.kernel.org/r/20190124115648.9433-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Cc: Joel Fernandes <joel@joelfernandes.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-15 06:41:22 +08:00
if (is_vn_id_valid(vn_id) && !vn->skip_populate)
if (node_pool_add_va(vn, va))
continue;
/* Go back to global. */
list_add(&va->list, &local_list);
}
reclaim_list_global(&local_list);
}
/*
* Purges all lazily-freed vmap areas.
*/
static bool __purge_vmap_area_lazy(unsigned long start, unsigned long end,
bool full_pool_decay)
{
unsigned long nr_purged_areas = 0;
unsigned int nr_purge_helpers;
unsigned int nr_purge_nodes;
struct vmap_node *vn;
int i;
lockdep_assert_held(&vmap_purge_lock);
/*
* Use cpumask to mark which node has to be processed.
*/
purge_nodes = CPU_MASK_NONE;
for (i = 0; i < nr_vmap_nodes; i++) {
vn = &vmap_nodes[i];
INIT_LIST_HEAD(&vn->purge_list);
vn->skip_populate = full_pool_decay;
decay_va_pool_node(vn, full_pool_decay);
if (RB_EMPTY_ROOT(&vn->lazy.root))
continue;
spin_lock(&vn->lazy.lock);
WRITE_ONCE(vn->lazy.root.rb_node, NULL);
list_replace_init(&vn->lazy.head, &vn->purge_list);
spin_unlock(&vn->lazy.lock);
start = min(start, list_first_entry(&vn->purge_list,
struct vmap_area, list)->va_start);
end = max(end, list_last_entry(&vn->purge_list,
struct vmap_area, list)->va_end);
cpumask_set_cpu(i, &purge_nodes);
}
nr_purge_nodes = cpumask_weight(&purge_nodes);
if (nr_purge_nodes > 0) {
flush_tlb_kernel_range(start, end);
/* One extra worker is per a lazy_max_pages() full set minus one. */
nr_purge_helpers = atomic_long_read(&vmap_lazy_nr) / lazy_max_pages();
nr_purge_helpers = clamp(nr_purge_helpers, 1U, nr_purge_nodes) - 1;
for_each_cpu(i, &purge_nodes) {
vn = &vmap_nodes[i];
if (nr_purge_helpers > 0) {
INIT_WORK(&vn->purge_work, purge_vmap_node);
if (cpumask_test_cpu(i, cpu_online_mask))
schedule_work_on(i, &vn->purge_work);
else
schedule_work(&vn->purge_work);
nr_purge_helpers--;
} else {
vn->purge_work.func = NULL;
purge_vmap_node(&vn->purge_work);
nr_purged_areas += vn->nr_purged;
}
}
for_each_cpu(i, &purge_nodes) {
vn = &vmap_nodes[i];
if (vn->purge_work.func) {
flush_work(&vn->purge_work);
nr_purged_areas += vn->nr_purged;
}
}
}
trace_purge_vmap_area_lazy(start, end, nr_purged_areas);
return nr_purged_areas > 0;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
/*
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
* Reclaim vmap areas by purging fragmented blocks and purge_vmap_area_list.
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
*/
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
static void reclaim_and_purge_vmap_areas(void)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
mutex_lock(&vmap_purge_lock);
purge_fragmented_blocks_allcpus();
__purge_vmap_area_lazy(ULONG_MAX, 0, true);
mutex_unlock(&vmap_purge_lock);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
mm/vmalloc: Move draining areas out of caller context A caller initiates the drain procces from its context once the drain threshold is reached or passed. There are at least two drawbacks of doing so: a) a caller can be a high-prio or RT task. In that case it can stuck in doing the actual drain of all lazily freed areas. This is not optimal because such tasks usually are latency sensitive where the control should be returned back as soon as possible in order to drive such workloads in time. See 96e2db456135 ("mm/vmalloc: rework the drain logic") b) It is not safe to call vfree() during holding a spinlock due to the vmap_purge_lock mutex. The was a report about this from Zeal Robot <zealci@zte.com.cn> here: https://lore.kernel.org/all/20211222081026.484058-1-chi.minghao@zte.com.cn Moving the drain to the separate work context addresses those issues. v1->v2: - Added prefix "_work" to the drain worker function. v2->v3: - Remove the drain_vmap_work_in_progress. Extra queuing is expectable under heavy load but it can be disregarded because a work will bail out if nothing to be done. Link: https://lkml.kernel.org/r/20220131144058.35608-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-23 05:42:50 +08:00
static void drain_vmap_area_work(struct work_struct *work)
{
mutex_lock(&vmap_purge_lock);
__purge_vmap_area_lazy(ULONG_MAX, 0, false);
mutex_unlock(&vmap_purge_lock);
mm/vmalloc: Move draining areas out of caller context A caller initiates the drain procces from its context once the drain threshold is reached or passed. There are at least two drawbacks of doing so: a) a caller can be a high-prio or RT task. In that case it can stuck in doing the actual drain of all lazily freed areas. This is not optimal because such tasks usually are latency sensitive where the control should be returned back as soon as possible in order to drive such workloads in time. See 96e2db456135 ("mm/vmalloc: rework the drain logic") b) It is not safe to call vfree() during holding a spinlock due to the vmap_purge_lock mutex. The was a report about this from Zeal Robot <zealci@zte.com.cn> here: https://lore.kernel.org/all/20211222081026.484058-1-chi.minghao@zte.com.cn Moving the drain to the separate work context addresses those issues. v1->v2: - Added prefix "_work" to the drain worker function. v2->v3: - Remove the drain_vmap_work_in_progress. Extra queuing is expectable under heavy load but it can be disregarded because a work will bail out if nothing to be done. Link: https://lkml.kernel.org/r/20220131144058.35608-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-23 05:42:50 +08:00
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
* Free a vmap area, caller ensuring that the area has been unmapped,
* unlinked and flush_cache_vunmap had been called for the correct
* range previously.
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
*/
vmalloc: eagerly clear ptes on vunmap On stock 2.6.37-rc4, running: # mount lilith:/export /mnt/lilith # find /mnt/lilith/ -type f -print0 | xargs -0 file crashes the machine fairly quickly under Xen. Often it results in oops messages, but the couple of times I tried just now, it just hung quietly and made Xen print some rude messages: (XEN) mm.c:2389:d80 Bad type (saw 7400000000000001 != exp 3000000000000000) for mfn 1d7058 (pfn 18fa7) (XEN) mm.c:964:d80 Attempt to create linear p.t. with write perms (XEN) mm.c:2389:d80 Bad type (saw 7400000000000010 != exp 1000000000000000) for mfn 1d2e04 (pfn 1d1fb) (XEN) mm.c:2965:d80 Error while pinning mfn 1d2e04 Which means the domain tried to map a pagetable page RW, which would allow it to map arbitrary memory, so Xen stopped it. This is because vm_unmap_ram() left some pages mapped in the vmalloc area after NFS had finished with them, and those pages got recycled as pagetable pages while still having these RW aliases. Removing those mappings immediately removes the Xen-visible aliases, and so it has no problem with those pages being reused as pagetable pages. Deferring the TLB flush doesn't upset Xen because it can flush the TLB itself as needed to maintain its invariants. When unmapping a region in the vmalloc space, clear the ptes immediately. There's no point in deferring this because there's no amortization benefit. The TLBs are left dirty, and they are flushed lazily to amortize the cost of the IPIs. This specific motivation for this patch is an oops-causing regression since 2.6.36 when using NFS under Xen, triggered by the NFS client's use of vm_map_ram() introduced in 56e4ebf877b60 ("NFS: readdir with vmapped pages") . XFS also uses vm_map_ram() and could cause similar problems. Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Nick Piggin <npiggin@kernel.dk> Cc: Bryan Schumaker <bjschuma@netapp.com> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: Alex Elder <aelder@sgi.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-12-03 06:31:18 +08:00
static void free_vmap_area_noflush(struct vmap_area *va)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
unsigned long nr_lazy_max = lazy_max_pages();
unsigned long va_start = va->va_start;
unsigned int vn_id = decode_vn_id(va->flags);
struct vmap_node *vn;
unsigned long nr_lazy;
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
if (WARN_ON_ONCE(!list_empty(&va->list)))
return;
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
nr_lazy = atomic_long_add_return((va->va_end - va->va_start) >>
PAGE_SHIFT, &vmap_lazy_nr);
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
/*
* If it was request by a certain node we would like to
* return it to that node, i.e. its pool for later reuse.
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
*/
vn = is_vn_id_valid(vn_id) ?
id_to_node(vn_id):addr_to_node(va->va_start);
spin_lock(&vn->lazy.lock);
insert_vmap_area(va, &vn->lazy.root, &vn->lazy.head);
spin_unlock(&vn->lazy.lock);
trace_free_vmap_area_noflush(va_start, nr_lazy, nr_lazy_max);
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
/* After this point, we may free va at any time */
if (unlikely(nr_lazy > nr_lazy_max))
mm/vmalloc: Move draining areas out of caller context A caller initiates the drain procces from its context once the drain threshold is reached or passed. There are at least two drawbacks of doing so: a) a caller can be a high-prio or RT task. In that case it can stuck in doing the actual drain of all lazily freed areas. This is not optimal because such tasks usually are latency sensitive where the control should be returned back as soon as possible in order to drive such workloads in time. See 96e2db456135 ("mm/vmalloc: rework the drain logic") b) It is not safe to call vfree() during holding a spinlock due to the vmap_purge_lock mutex. The was a report about this from Zeal Robot <zealci@zte.com.cn> here: https://lore.kernel.org/all/20211222081026.484058-1-chi.minghao@zte.com.cn Moving the drain to the separate work context addresses those issues. v1->v2: - Added prefix "_work" to the drain worker function. v2->v3: - Remove the drain_vmap_work_in_progress. Extra queuing is expectable under heavy load but it can be disregarded because a work will bail out if nothing to be done. Link: https://lkml.kernel.org/r/20220131144058.35608-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-23 05:42:50 +08:00
schedule_work(&drain_vmap_work);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
/*
* Free and unmap a vmap area
*/
static void free_unmap_vmap_area(struct vmap_area *va)
{
flush_cache_vunmap(va->va_start, va->va_end);
vunmap_range_noflush(va->va_start, va->va_end);
mm, debug_pagealloc: don't rely on static keys too early Commit 96a2b03f281d ("mm, debug_pagelloc: use static keys to enable debugging") has introduced a static key to reduce overhead when debug_pagealloc is compiled in but not enabled. It relied on the assumption that jump_label_init() is called before parse_early_param() as in start_kernel(), so when the "debug_pagealloc=on" option is parsed, it is safe to enable the static key. However, it turns out multiple architectures call parse_early_param() earlier from their setup_arch(). x86 also calls jump_label_init() even earlier, so no issue was found while testing the commit, but same is not true for e.g. ppc64 and s390 where the kernel would not boot with debug_pagealloc=on as found by our QA. To fix this without tricky changes to init code of multiple architectures, this patch partially reverts the static key conversion from 96a2b03f281d. Init-time and non-fastpath calls (such as in arch code) of debug_pagealloc_enabled() will again test a simple bool variable. Fastpath mm code is converted to a new debug_pagealloc_enabled_static() variant that relies on the static key, which is enabled in a well-defined point in mm_init() where it's guaranteed that jump_label_init() has been called, regardless of architecture. [sfr@canb.auug.org.au: export _debug_pagealloc_enabled_early] Link: http://lkml.kernel.org/r/20200106164944.063ac07b@canb.auug.org.au Link: http://lkml.kernel.org/r/20191219130612.23171-1-vbabka@suse.cz Fixes: 96a2b03f281d ("mm, debug_pagelloc: use static keys to enable debugging") Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Qian Cai <cai@lca.pw> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-01-14 08:29:20 +08:00
if (debug_pagealloc_enabled_static())
flush_tlb_kernel_range(va->va_start, va->va_end);
free_vmap_area_noflush(va);
}
struct vmap_area *find_vmap_area(unsigned long addr)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
struct vmap_area *va;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
int i, j;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm: vmalloc: bail out early in find_vmap_area() if vmap is not init During the boot the s390 system triggers "spinlock bad magic" messages if the spinlock debugging is enabled: [ 0.465445] BUG: spinlock bad magic on CPU#0, swapper/0 [ 0.465490] lock: single+0x1860/0x1958, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0 [ 0.466067] CPU: 0 PID: 0 Comm: swapper Not tainted 6.8.0-12955-g8e938e398669 #1 [ 0.466188] Hardware name: QEMU 8561 QEMU (KVM/Linux) [ 0.466270] Call Trace: [ 0.466470] [<00000000011f26c8>] dump_stack_lvl+0x98/0xd8 [ 0.466516] [<00000000001dcc6a>] do_raw_spin_lock+0x8a/0x108 [ 0.466545] [<000000000042146c>] find_vmap_area+0x6c/0x108 [ 0.466572] [<000000000042175a>] find_vm_area+0x22/0x40 [ 0.466597] [<000000000012f152>] __set_memory+0x132/0x150 [ 0.466624] [<0000000001cc0398>] vmem_map_init+0x40/0x118 [ 0.466651] [<0000000001cc0092>] paging_init+0x22/0x68 [ 0.466677] [<0000000001cbbed2>] setup_arch+0x52a/0x708 [ 0.466702] [<0000000001cb6140>] start_kernel+0x80/0x5c8 [ 0.466727] [<0000000000100036>] startup_continue+0x36/0x40 it happens because such system tries to access some vmap areas whereas the vmalloc initialization is not even yet done: [ 0.465490] lock: single+0x1860/0x1958, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0 [ 0.466067] CPU: 0 PID: 0 Comm: swapper Not tainted 6.8.0-12955-g8e938e398669 #1 [ 0.466188] Hardware name: QEMU 8561 QEMU (KVM/Linux) [ 0.466270] Call Trace: [ 0.466470] dump_stack_lvl (lib/dump_stack.c:117) [ 0.466516] do_raw_spin_lock (kernel/locking/spinlock_debug.c:87 kernel/locking/spinlock_debug.c:115) [ 0.466545] find_vmap_area (mm/vmalloc.c:1059 mm/vmalloc.c:2364) [ 0.466572] find_vm_area (mm/vmalloc.c:3150) [ 0.466597] __set_memory (arch/s390/mm/pageattr.c:360 arch/s390/mm/pageattr.c:393) [ 0.466624] vmem_map_init (./arch/s390/include/asm/set_memory.h:55 arch/s390/mm/vmem.c:660) [ 0.466651] paging_init (arch/s390/mm/init.c:97) [ 0.466677] setup_arch (arch/s390/kernel/setup.c:972) [ 0.466702] start_kernel (init/main.c:899) [ 0.466727] startup_continue (arch/s390/kernel/head64.S:35) [ 0.466811] INFO: lockdep is turned off. ... [ 0.718250] vmalloc init - busy lock init 0000000002871860 [ 0.718328] vmalloc init - busy lock init 00000000028731b8 Some background. It worked before because the lock that is in question was statically defined and initialized. As of now, the locks and data structures are initialized in the vmalloc_init() function. To address that issue add the check whether the "vmap_initialized" variable is set, if not find_vmap_area() bails out on entry returning NULL. Link: https://lkml.kernel.org/r/20240323141544.4150-1-urezki@gmail.com Fixes: 72210662c5a2 ("mm: vmalloc: offload free_vmap_area_lock lock") Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Baoquan He <bhe@redhat.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-23 22:15:44 +08:00
if (unlikely(!vmap_initialized))
return NULL;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
/*
* An addr_to_node_id(addr) converts an address to a node index
* where a VA is located. If VA spans several zones and passed
* addr is not the same as va->va_start, what is not common, we
* may need to scan extra nodes. See an example:
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
*
* <----va---->
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
* -|-----|-----|-----|-----|-
* 1 2 0 1
*
* VA resides in node 1 whereas it spans 1, 2 an 0. If passed
* addr is within 2 or 0 nodes we should do extra work.
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
*/
i = j = addr_to_node_id(addr);
do {
vn = &vmap_nodes[i];
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
spin_lock(&vn->busy.lock);
va = __find_vmap_area(addr, &vn->busy.root);
spin_unlock(&vn->busy.lock);
if (va)
return va;
} while ((i = (i + 1) % nr_vmap_nodes) != j);
return NULL;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
static struct vmap_area *find_unlink_vmap_area(unsigned long addr)
{
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn;
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
struct vmap_area *va;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
int i, j;
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
/*
* Check the comment in the find_vmap_area() about the loop.
*/
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
i = j = addr_to_node_id(addr);
do {
vn = &vmap_nodes[i];
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
spin_lock(&vn->busy.lock);
va = __find_vmap_area(addr, &vn->busy.root);
if (va)
unlink_va(va, &vn->busy.root);
spin_unlock(&vn->busy.lock);
if (va)
return va;
} while ((i = (i + 1) % nr_vmap_nodes) != j);
return NULL;
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*** Per cpu kva allocator ***/
/*
* vmap space is limited especially on 32 bit architectures. Ensure there is
* room for at least 16 percpu vmap blocks per CPU.
*/
/*
* If we had a constant VMALLOC_START and VMALLOC_END, we'd like to be able
* to #define VMALLOC_SPACE (VMALLOC_END-VMALLOC_START). Guess
* instead (we just need a rough idea)
*/
#if BITS_PER_LONG == 32
#define VMALLOC_SPACE (128UL*1024*1024)
#else
#define VMALLOC_SPACE (128UL*1024*1024*1024)
#endif
#define VMALLOC_PAGES (VMALLOC_SPACE / PAGE_SIZE)
#define VMAP_MAX_ALLOC BITS_PER_LONG /* 256K with 4K pages */
#define VMAP_BBMAP_BITS_MAX 1024 /* 4MB with 4K pages */
#define VMAP_BBMAP_BITS_MIN (VMAP_MAX_ALLOC*2)
#define VMAP_MIN(x, y) ((x) < (y) ? (x) : (y)) /* can't use min() */
#define VMAP_MAX(x, y) ((x) > (y) ? (x) : (y)) /* can't use max() */
#define VMAP_BBMAP_BITS \
VMAP_MIN(VMAP_BBMAP_BITS_MAX, \
VMAP_MAX(VMAP_BBMAP_BITS_MIN, \
VMALLOC_PAGES / roundup_pow_of_two(NR_CPUS) / 16))
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
#define VMAP_BLOCK_SIZE (VMAP_BBMAP_BITS * PAGE_SIZE)
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
/*
* Purge threshold to prevent overeager purging of fragmented blocks for
* regular operations: Purge if vb->free is less than 1/4 of the capacity.
*/
#define VMAP_PURGE_THRESHOLD (VMAP_BBMAP_BITS / 4)
mm/vmalloc.c: add flags to mark vm_map_ram area Through vmalloc API, a virtual kernel area is reserved for physical address mapping. And vmap_area is used to track them, while vm_struct is allocated to associate with the vmap_area to store more information and passed out. However, area reserved via vm_map_ram() is an exception. It doesn't have vm_struct to associate with vmap_area. And we can't recognize the vmap_area with '->vm == NULL' as a vm_map_ram() area because the normal freeing path will set va->vm = NULL before unmapping, please see function remove_vm_area(). Meanwhile, there are two kinds of handling for vm_map_ram area. One is the whole vmap_area being reserved and mapped at one time through vm_map_area() interface; the other is the whole vmap_area with VMAP_BLOCK_SIZE size being reserved, while mapped into split regions with smaller size via vb_alloc(). To mark the area reserved through vm_map_ram(), add flags field into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, while bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-3-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:15 +08:00
#define VMAP_RAM 0x1 /* indicates vm_map_ram area*/
#define VMAP_BLOCK 0x2 /* mark out the vmap_block sub-type*/
#define VMAP_FLAGS_MASK 0x3
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
struct vmap_block_queue {
spinlock_t lock;
struct list_head free;
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
/*
* An xarray requires an extra memory dynamically to
* be allocated. If it is an issue, we can use rb-tree
* instead.
*/
struct xarray vmap_blocks;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
};
struct vmap_block {
spinlock_t lock;
struct vmap_area *va;
unsigned long free, dirty;
mm/vmalloc.c: add used_map into vmap_block to track space of vmap_block Patch series "mm/vmalloc.c: allow vread() to read out vm_map_ram areas", v5. Problem: *** Stephen reported vread() will skip vm_map_ram areas when reading out /proc/kcore with drgn utility. Please see below link to get more details. /proc/kcore reads 0's for vmap_block https://lore.kernel.org/all/87ilk6gos2.fsf@oracle.com/T/#u Root cause: *** The normal vmalloc API uses struct vmap_area to manage the virtual kernel area allocated, and associate a vm_struct to store more information and pass out. However, area reserved through vm_map_ram() interface doesn't allocate vm_struct to associate with. So the current code in vread() will skip the vm_map_ram area through 'if (!va->vm)' conditional checking. Solution: *** To mark the area reserved through vm_map_ram() interface, add field 'flags' into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). And also add bitmap field 'used_map' into struct vmap_block to mark those further subdivided regions being used to differentiate with dirty and free regions in vmap_block. With the help of above vmap_area->flags and vmap_block->used_map, we can recognize and handle vm_map_ram areas successfully. All these are done in patch 1~3. Meanwhile, do some improvement on areas related to vm_map_ram areas in patch 4, 5. And also change area flag from VM_ALLOC to VM_IOREMAP in patch 6, 7 because this will show them as 'ioremap' in /proc/vmallocinfo, and exclude them from /proc/kcore. This patch (of 7): In one vmap_block area, there could be three types of regions: region being used which is allocated through vb_alloc(), dirty region which is freed via vb_free() and free region. Among them, only used region has available data. While there's no way to track those used regions currently. Here, add bitmap field used_map into vmap_block, and set/clear it during allocation or freeing regions of vmap_block area. This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-1-bhe@redhat.com Link: https://lkml.kernel.org/r/20230206084020.174506-2-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:14 +08:00
DECLARE_BITMAP(used_map, VMAP_BBMAP_BITS);
mm/vmalloc: get rid of dirty bitmap inside vmap_block structure In original implementation of vm_map_ram made by Nick Piggin there were two bitmaps: alloc_map and dirty_map. None of them were used as supposed to be: finding a suitable free hole for next allocation in block. vm_map_ram allocates space sequentially in block and on free call marks pages as dirty, so freed space can't be reused anymore. Actually it would be very interesting to know the real meaning of those bitmaps, maybe implementation was incomplete, etc. But long time ago Zhang Yanfei removed alloc_map by these two commits: mm/vmalloc.c: remove dead code in vb_alloc 3fcd76e8028e0be37b02a2002b4f56755daeda06 mm/vmalloc.c: remove alloc_map from vmap_block b8e748b6c32999f221ea4786557b8e7e6c4e4e7a In this patch I replaced dirty_map with two range variables: dirty min and max. These variables store minimum and maximum position of dirty space in a block, since we need only to know the dirty range, not exact position of dirty pages. Why it was made? Several reasons: at first glance it seems that vm_map_ram allocator concerns about fragmentation thus it uses bitmaps for finding free hole, but it is not true. To avoid complexity seems it is better to use something simple, like min or max range values. Secondly, code also becomes simpler, without iteration over bitmap, just comparing values in min and max macros. Thirdly, bitmap occupies up to 1024 bits (4MB is a max size of a block). Here I replaced the whole bitmap with two longs. Finally vm_unmap_aliases should be slightly faster and the whole vmap_block structure occupies less memory. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:55 +08:00
unsigned long dirty_min, dirty_max; /*< dirty range */
struct list_head free_list;
struct rcu_head rcu_head;
struct list_head purge;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
};
/* Queue of free and dirty vmap blocks, for allocation and flushing purposes */
static DEFINE_PER_CPU(struct vmap_block_queue, vmap_block_queue);
/*
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
* In order to fast access to any "vmap_block" associated with a
* specific address, we use a hash.
*
* A per-cpu vmap_block_queue is used in both ways, to serialize
* an access to free block chains among CPUs(alloc path) and it
* also acts as a vmap_block hash(alloc/free paths). It means we
* overload it, since we already have the per-cpu array which is
* used as a hash table. When used as a hash a 'cpu' passed to
* per_cpu() is not actually a CPU but rather a hash index.
*
* A hash function is addr_to_vb_xa() which hashes any address
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
* to a specific index(in a hash) it belongs to. This then uses a
* per_cpu() macro to access an array with generated index.
*
* An example:
*
* CPU_1 CPU_2 CPU_0
* | | |
* V V V
* 0 10 20 30 40 50 60
* |------|------|------|------|------|------|...<vmap address space>
* CPU0 CPU1 CPU2 CPU0 CPU1 CPU2
*
* - CPU_1 invokes vm_unmap_ram(6), 6 belongs to CPU0 zone, thus
* it access: CPU0/INDEX0 -> vmap_blocks -> xa_lock;
*
* - CPU_2 invokes vm_unmap_ram(11), 11 belongs to CPU1 zone, thus
* it access: CPU1/INDEX1 -> vmap_blocks -> xa_lock;
*
* - CPU_0 invokes vm_unmap_ram(20), 20 belongs to CPU2 zone, thus
* it access: CPU2/INDEX2 -> vmap_blocks -> xa_lock.
*
* This technique almost always avoids lock contention on insert/remove,
* however xarray spinlocks protect against any contention that remains.
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
*/
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
static struct xarray *
addr_to_vb_xa(unsigned long addr)
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
{
int index = (addr / VMAP_BLOCK_SIZE) % num_possible_cpus();
return &per_cpu(vmap_block_queue, index).vmap_blocks;
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/*
* We should probably have a fallback mechanism to allocate virtual memory
* out of partially filled vmap blocks. However vmap block sizing should be
* fairly reasonable according to the vmalloc size, so it shouldn't be a
* big problem.
*/
static unsigned long addr_to_vb_idx(unsigned long addr)
{
addr -= VMALLOC_START & ~(VMAP_BLOCK_SIZE-1);
addr /= VMAP_BLOCK_SIZE;
return addr;
}
static void *vmap_block_vaddr(unsigned long va_start, unsigned long pages_off)
{
unsigned long addr;
addr = va_start + (pages_off << PAGE_SHIFT);
BUG_ON(addr_to_vb_idx(addr) != addr_to_vb_idx(va_start));
return (void *)addr;
}
/**
* new_vmap_block - allocates new vmap_block and occupies 2^order pages in this
* block. Of course pages number can't exceed VMAP_BBMAP_BITS
* @order: how many 2^order pages should be occupied in newly allocated block
* @gfp_mask: flags for the page level allocator
*
* Return: virtual address in a newly allocated block or ERR_PTR(-errno)
*/
static void *new_vmap_block(unsigned int order, gfp_t gfp_mask)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
struct vmap_block_queue *vbq;
struct vmap_block *vb;
struct vmap_area *va;
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
struct xarray *xa;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
unsigned long vb_idx;
int node, err;
void *vaddr;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
node = numa_node_id();
vb = kmalloc_node(sizeof(struct vmap_block),
gfp_mask & GFP_RECLAIM_MASK, node);
if (unlikely(!vb))
return ERR_PTR(-ENOMEM);
va = alloc_vmap_area(VMAP_BLOCK_SIZE, VMAP_BLOCK_SIZE,
VMALLOC_START, VMALLOC_END,
mm/vmalloc.c: add flags to mark vm_map_ram area Through vmalloc API, a virtual kernel area is reserved for physical address mapping. And vmap_area is used to track them, while vm_struct is allocated to associate with the vmap_area to store more information and passed out. However, area reserved via vm_map_ram() is an exception. It doesn't have vm_struct to associate with vmap_area. And we can't recognize the vmap_area with '->vm == NULL' as a vm_map_ram() area because the normal freeing path will set va->vm = NULL before unmapping, please see function remove_vm_area(). Meanwhile, there are two kinds of handling for vm_map_ram area. One is the whole vmap_area being reserved and mapped at one time through vm_map_area() interface; the other is the whole vmap_area with VMAP_BLOCK_SIZE size being reserved, while mapped into split regions with smaller size via vb_alloc(). To mark the area reserved through vm_map_ram(), add flags field into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, while bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-3-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:15 +08:00
node, gfp_mask,
VMAP_RAM|VMAP_BLOCK, NULL);
if (IS_ERR(va)) {
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
kfree(vb);
return ERR_CAST(va);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
vaddr = vmap_block_vaddr(va->va_start, 0);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
spin_lock_init(&vb->lock);
vb->va = va;
/* At least something should be left free */
BUG_ON(VMAP_BBMAP_BITS <= (1UL << order));
mm/vmalloc.c: add used_map into vmap_block to track space of vmap_block Patch series "mm/vmalloc.c: allow vread() to read out vm_map_ram areas", v5. Problem: *** Stephen reported vread() will skip vm_map_ram areas when reading out /proc/kcore with drgn utility. Please see below link to get more details. /proc/kcore reads 0's for vmap_block https://lore.kernel.org/all/87ilk6gos2.fsf@oracle.com/T/#u Root cause: *** The normal vmalloc API uses struct vmap_area to manage the virtual kernel area allocated, and associate a vm_struct to store more information and pass out. However, area reserved through vm_map_ram() interface doesn't allocate vm_struct to associate with. So the current code in vread() will skip the vm_map_ram area through 'if (!va->vm)' conditional checking. Solution: *** To mark the area reserved through vm_map_ram() interface, add field 'flags' into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). And also add bitmap field 'used_map' into struct vmap_block to mark those further subdivided regions being used to differentiate with dirty and free regions in vmap_block. With the help of above vmap_area->flags and vmap_block->used_map, we can recognize and handle vm_map_ram areas successfully. All these are done in patch 1~3. Meanwhile, do some improvement on areas related to vm_map_ram areas in patch 4, 5. And also change area flag from VM_ALLOC to VM_IOREMAP in patch 6, 7 because this will show them as 'ioremap' in /proc/vmallocinfo, and exclude them from /proc/kcore. This patch (of 7): In one vmap_block area, there could be three types of regions: region being used which is allocated through vb_alloc(), dirty region which is freed via vb_free() and free region. Among them, only used region has available data. While there's no way to track those used regions currently. Here, add bitmap field used_map into vmap_block, and set/clear it during allocation or freeing regions of vmap_block area. This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-1-bhe@redhat.com Link: https://lkml.kernel.org/r/20230206084020.174506-2-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:14 +08:00
bitmap_zero(vb->used_map, VMAP_BBMAP_BITS);
vb->free = VMAP_BBMAP_BITS - (1UL << order);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
vb->dirty = 0;
mm/vmalloc: get rid of dirty bitmap inside vmap_block structure In original implementation of vm_map_ram made by Nick Piggin there were two bitmaps: alloc_map and dirty_map. None of them were used as supposed to be: finding a suitable free hole for next allocation in block. vm_map_ram allocates space sequentially in block and on free call marks pages as dirty, so freed space can't be reused anymore. Actually it would be very interesting to know the real meaning of those bitmaps, maybe implementation was incomplete, etc. But long time ago Zhang Yanfei removed alloc_map by these two commits: mm/vmalloc.c: remove dead code in vb_alloc 3fcd76e8028e0be37b02a2002b4f56755daeda06 mm/vmalloc.c: remove alloc_map from vmap_block b8e748b6c32999f221ea4786557b8e7e6c4e4e7a In this patch I replaced dirty_map with two range variables: dirty min and max. These variables store minimum and maximum position of dirty space in a block, since we need only to know the dirty range, not exact position of dirty pages. Why it was made? Several reasons: at first glance it seems that vm_map_ram allocator concerns about fragmentation thus it uses bitmaps for finding free hole, but it is not true. To avoid complexity seems it is better to use something simple, like min or max range values. Secondly, code also becomes simpler, without iteration over bitmap, just comparing values in min and max macros. Thirdly, bitmap occupies up to 1024 bits (4MB is a max size of a block). Here I replaced the whole bitmap with two longs. Finally vm_unmap_aliases should be slightly faster and the whole vmap_block structure occupies less memory. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:55 +08:00
vb->dirty_min = VMAP_BBMAP_BITS;
vb->dirty_max = 0;
mm/vmalloc.c: add used_map into vmap_block to track space of vmap_block Patch series "mm/vmalloc.c: allow vread() to read out vm_map_ram areas", v5. Problem: *** Stephen reported vread() will skip vm_map_ram areas when reading out /proc/kcore with drgn utility. Please see below link to get more details. /proc/kcore reads 0's for vmap_block https://lore.kernel.org/all/87ilk6gos2.fsf@oracle.com/T/#u Root cause: *** The normal vmalloc API uses struct vmap_area to manage the virtual kernel area allocated, and associate a vm_struct to store more information and pass out. However, area reserved through vm_map_ram() interface doesn't allocate vm_struct to associate with. So the current code in vread() will skip the vm_map_ram area through 'if (!va->vm)' conditional checking. Solution: *** To mark the area reserved through vm_map_ram() interface, add field 'flags' into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). And also add bitmap field 'used_map' into struct vmap_block to mark those further subdivided regions being used to differentiate with dirty and free regions in vmap_block. With the help of above vmap_area->flags and vmap_block->used_map, we can recognize and handle vm_map_ram areas successfully. All these are done in patch 1~3. Meanwhile, do some improvement on areas related to vm_map_ram areas in patch 4, 5. And also change area flag from VM_ALLOC to VM_IOREMAP in patch 6, 7 because this will show them as 'ioremap' in /proc/vmallocinfo, and exclude them from /proc/kcore. This patch (of 7): In one vmap_block area, there could be three types of regions: region being used which is allocated through vb_alloc(), dirty region which is freed via vb_free() and free region. Among them, only used region has available data. While there's no way to track those used regions currently. Here, add bitmap field used_map into vmap_block, and set/clear it during allocation or freeing regions of vmap_block area. This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-1-bhe@redhat.com Link: https://lkml.kernel.org/r/20230206084020.174506-2-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:14 +08:00
bitmap_set(vb->used_map, 0, (1UL << order));
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
INIT_LIST_HEAD(&vb->free_list);
xa = addr_to_vb_xa(va->va_start);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
vb_idx = addr_to_vb_idx(va->va_start);
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
err = xa_insert(xa, vb_idx, vb, gfp_mask);
if (err) {
kfree(vb);
free_vmap_area(va);
return ERR_PTR(err);
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
vbq = raw_cpu_ptr(&vmap_block_queue);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
spin_lock(&vbq->lock);
mm/vmalloc: fix possible exhaustion of vmalloc space caused by vm_map_ram allocator Recently I came across high fragmentation of vm_map_ram allocator: vmap_block has free space, but still new blocks continue to appear. Further investigation showed that certain mapping/unmapping sequences can exhaust vmalloc space. On small 32bit systems that's not a big problem, cause purging will be called soon on a first allocation failure (alloc_vmap_area), but on 64bit machines, e.g. x86_64 has 45 bits of vmalloc space, that can be a disaster. 1) I came up with a simple allocation sequence, which exhausts virtual space very quickly: while (iters) { /* Map/unmap big chunk */ vaddr = vm_map_ram(pages, 16, -1, PAGE_KERNEL); vm_unmap_ram(vaddr, 16); /* Map/unmap small chunks. * * -1 for hole, which should be left at the end of each block * to keep it partially used, with some free space available */ for (i = 0; i < (VMAP_BBMAP_BITS - 16) / 8 - 1; i++) { vaddr = vm_map_ram(pages, 8, -1, PAGE_KERNEL); vm_unmap_ram(vaddr, 8); } } The idea behind is simple: 1. We have to map a big chunk, e.g. 16 pages. 2. Then we have to occupy the remaining space with smaller chunks, i.e. 8 pages. At the end small hole should remain to keep block in free list, but do not let big chunk to occupy remaining space. 3. Goto 1 - allocation request of 16 pages can't be completed (only 8 slots are left free in the block in the #2 step), new block will be allocated, all further requests will lay into newly allocated block. To have some measurement numbers for all further tests I setup ftrace and enabled 4 basic calls in a function profile: echo vm_map_ram > /sys/kernel/debug/tracing/set_ftrace_filter; echo alloc_vmap_area >> /sys/kernel/debug/tracing/set_ftrace_filter; echo vm_unmap_ram >> /sys/kernel/debug/tracing/set_ftrace_filter; echo free_vmap_block >> /sys/kernel/debug/tracing/set_ftrace_filter; So for this scenario I got these results: BEFORE (all new blocks are put to the head of a free list) # cat /sys/kernel/debug/tracing/trace_stat/function0 Function Hit Time Avg s^2 -------- --- ---- --- --- vm_map_ram 126000 30683.30 us 0.243 us 30819.36 us vm_unmap_ram 126000 22003.24 us 0.174 us 340.886 us alloc_vmap_area 1000 4132.065 us 4.132 us 0.903 us AFTER (all new blocks are put to the tail of a free list) # cat /sys/kernel/debug/tracing/trace_stat/function0 Function Hit Time Avg s^2 -------- --- ---- --- --- vm_map_ram 126000 28713.13 us 0.227 us 24944.70 us vm_unmap_ram 126000 20403.96 us 0.161 us 1429.872 us alloc_vmap_area 993 3916.795 us 3.944 us 29.370 us free_vmap_block 992 654.157 us 0.659 us 1.273 us SUMMARY: The most interesting numbers in those tables are numbers of block allocations and deallocations: alloc_vmap_area and free_vmap_block calls, which show that before the change blocks were not freed, and virtual space and physical memory (vmap_block structure allocations, etc) were consumed. Average time which were spent in vm_map_ram/vm_unmap_ram became slightly better. That can be explained with a reasonable amount of blocks in a free list, which we need to iterate to find a suitable free block. 2) Another scenario is a random allocation: while (iters) { /* Randomly take number from a range [1..32/64] */ nr = rand(1, VMAP_MAX_ALLOC); vaddr = vm_map_ram(pages, nr, -1, PAGE_KERNEL); vm_unmap_ram(vaddr, nr); } I chose mersenne twister PRNG to generate persistent random state to guarantee that both runs have the same random sequence. For each vm_map_ram call random number from [1..32/64] was taken to represent amount of pages which I do map. I did 10'000 vm_map_ram calls and got these two tables: BEFORE (all new blocks are put to the head of a free list) # cat /sys/kernel/debug/tracing/trace_stat/function0 Function Hit Time Avg s^2 -------- --- ---- --- --- vm_map_ram 10000 10170.01 us 1.017 us 993.609 us vm_unmap_ram 10000 5321.823 us 0.532 us 59.789 us alloc_vmap_area 420 2150.239 us 5.119 us 3.307 us free_vmap_block 37 159.587 us 4.313 us 134.344 us AFTER (all new blocks are put to the tail of a free list) # cat /sys/kernel/debug/tracing/trace_stat/function0 Function Hit Time Avg s^2 -------- --- ---- --- --- vm_map_ram 10000 7745.637 us 0.774 us 395.229 us vm_unmap_ram 10000 5460.573 us 0.546 us 67.187 us alloc_vmap_area 414 2201.650 us 5.317 us 5.591 us free_vmap_block 412 574.421 us 1.394 us 15.138 us SUMMARY: 'BEFORE' table shows, that 420 blocks were allocated and only 37 were freed. Remained 383 blocks are still in a free list, consuming virtual space and physical memory. 'AFTER' table shows, that 414 blocks were allocated and 412 were really freed. 2 blocks remained in a free list. So fragmentation was dramatically reduced. Why? Because when we put newly allocated block to the head, all further requests will occupy new block, regardless remained space in other blocks. In this scenario all requests come randomly. Eventually remained free space will be less than requested size, free list will be iterated and it is possible that nothing will be found there - finally new block will be created. So exhaustion in random scenario happens for the maximum possible allocation size: 32 pages for 32-bit system and 64 pages for 64-bit system. Also average cost of vm_map_ram was reduced from 1.017 us to 0.774 us. Again this can be explained by iteration through smaller list of free blocks. 3) Next simple scenario is a sequential allocation, when the allocation order is increased for each block. This scenario forces allocator to reach maximum amount of partially free blocks in a free list: while (iters) { /* Populate free list with blocks with remaining space */ for (order = 0; order <= ilog2(VMAP_MAX_ALLOC); order++) { nr = VMAP_BBMAP_BITS / (1 << order); /* Leave a hole */ nr -= 1; for (i = 0; i < nr; i++) { vaddr = vm_map_ram(pages, (1 << order), -1, PAGE_KERNEL); vm_unmap_ram(vaddr, (1 << order)); } /* Completely occupy blocks from a free list */ for (order = 0; order <= ilog2(VMAP_MAX_ALLOC); order++) { vaddr = vm_map_ram(pages, (1 << order), -1, PAGE_KERNEL); vm_unmap_ram(vaddr, (1 << order)); } } Results which I got: BEFORE (all new blocks are put to the head of a free list) # cat /sys/kernel/debug/tracing/trace_stat/function0 Function Hit Time Avg s^2 -------- --- ---- --- --- vm_map_ram 2032000 399545.2 us 0.196 us 467123.7 us vm_unmap_ram 2032000 363225.7 us 0.178 us 111405.9 us alloc_vmap_area 7001 30627.76 us 4.374 us 495.755 us free_vmap_block 6993 7011.685 us 1.002 us 159.090 us AFTER (all new blocks are put to the tail of a free list) # cat /sys/kernel/debug/tracing/trace_stat/function0 Function Hit Time Avg s^2 -------- --- ---- --- --- vm_map_ram 2032000 394259.7 us 0.194 us 589395.9 us vm_unmap_ram 2032000 292500.7 us 0.143 us 94181.08 us alloc_vmap_area 7000 31103.11 us 4.443 us 703.225 us free_vmap_block 7000 6750.844 us 0.964 us 119.112 us SUMMARY: No surprises here, almost all numbers are the same. Fixing this fragmentation problem I also did some improvements in a allocation logic of a new vmap block: occupy block immediately and get rid of extra search in a free list. Also I replaced dirty bitmap with min/max dirty range values to make the logic simpler and slightly faster, since two longs comparison costs less, than loop thru bitmap. This patchset raises several questions: Q: Think the problem you comments is already known so that I wrote comments about it as "it could consume lots of address space through fragmentation". Could you tell me about your situation and reason why it should be avoided? Gioh Kim A: Indeed, there was a commit 364376383 which adds explicit comment about fragmentation. But fragmentation which is described in this comment caused by mixing of long-lived and short-lived objects, when a whole block is pinned in memory because some page slots are still in use. But here I am talking about blocks which are free, nobody uses them, and allocator keeps them alive forever, continuously allocating new blocks. Q: I think that if you put newly allocated block to the tail of a free list, below example would results in enormous performance degradation. new block: 1MB (256 pages) while (iters--) { vm_map_ram(3 or something else not dividable for 256) * 85 vm_unmap_ram(3) * 85 } On every iteration, it needs newly allocated block and it is put to the tail of a free list so finding it consumes large amount of time. Joonsoo Kim A: Second patch in current patchset gets rid of extra search in a free list, so new block will be immediately occupied.. Also, the scenario above is impossible, cause vm_map_ram allocates virtual range in orders, i.e. 2^n. I.e. passing 3 to vm_map_ram you will allocate 4 slots in a block and 256 slots (capacity of a block) of course dividable on 4, so block will be completely occupied. But there is a worst case which we can achieve: each free block has a hole equal to order size. The maximum size of allocation is 64 pages for 64-bit system (if you try to map more, original alloc_vmap_area will be called). So the maximum order is 6. That means that worst case, before allocator makes a decision to allocate a new block, is to iterate 7 blocks: HEAD 1st block - has 1 page slot free (order 0) 2nd block - has 2 page slots free (order 1) 3rd block - has 4 page slots free (order 2) 4th block - has 8 page slots free (order 3) 5th block - has 16 page slots free (order 4) 6th block - has 32 page slots free (order 5) 7th block - has 64 page slots free (order 6) TAIL So the worst scenario on 64-bit system is that each CPU queue can have 7 blocks in a free list. This can happen only and only if you allocate blocks increasing the order. (as I did in the function written in the comment of the first patch) This is weird and rare case, but still it is possible. Afterwards you will get 7 blocks in a list. All further requests should be placed in a newly allocated block or some free slots should be found in a free list. Seems it does not look dramatically awful. This patch (of 3): If suitable block can't be found, new block is allocated and put into a head of a free list, so on next iteration this new block will be found first. That's bad, because old blocks in a free list will not get a chance to be fully used, thus fragmentation will grow. Let's consider this simple example: #1 We have one block in a free list which is partially used, and where only one page is free: HEAD |xxxxxxxxx-| TAIL ^ free space for 1 page, order 0 #2 New allocation request of order 1 (2 pages) comes, new block is allocated since we do not have free space to complete this request. New block is put into a head of a free list: HEAD |----------|xxxxxxxxx-| TAIL #3 Two pages were occupied in a new found block: HEAD |xx--------|xxxxxxxxx-| TAIL ^ two pages mapped here #4 New allocation request of order 0 (1 page) comes. Block, which was created on #2 step, is located at the beginning of a free list, so it will be found first: HEAD |xxX-------|xxxxxxxxx-| TAIL ^ ^ page mapped here, but better to use this hole It is obvious, that it is better to complete request of #4 step using the old block, where free space is left, because in other case fragmentation will be highly increased. But fragmentation is not only the case. The worst thing is that I can easily create scenario, when the whole vmalloc space is exhausted by blocks, which are not used, but already dirty and have several free pages. Let's consider this function which execution should be pinned to one CPU: static void exhaust_virtual_space(struct page *pages[16], int iters) { /* Firstly we have to map a big chunk, e.g. 16 pages. * Then we have to occupy the remaining space with smaller * chunks, i.e. 8 pages. At the end small hole should remain. * So at the end of our allocation sequence block looks like * this: * XX big chunk * |XXxxxxxxx-| x small chunk * - hole, which is enough for a small chunk, * but is not enough for a big chunk */ while (iters--) { int i; void *vaddr; /* Map/unmap big chunk */ vaddr = vm_map_ram(pages, 16, -1, PAGE_KERNEL); vm_unmap_ram(vaddr, 16); /* Map/unmap small chunks. * * -1 for hole, which should be left at the end of each block * to keep it partially used, with some free space available */ for (i = 0; i < (VMAP_BBMAP_BITS - 16) / 8 - 1; i++) { vaddr = vm_map_ram(pages, 8, -1, PAGE_KERNEL); vm_unmap_ram(vaddr, 8); } } } On every iteration new block (1MB of vm area in my case) will be allocated and then will be occupied, without attempt to resolve small allocation request using previously allocated blocks in a free list. In case of random allocation (size should be randomly taken from the range [1..64] in 64-bit case or [1..32] in 32-bit case) situation is the same: new blocks continue to appear if maximum possible allocation size (32 or 64) passed to the allocator, because all remaining blocks in a free list do not have enough free space to complete this allocation request. In summary if new blocks are put into the head of a free list eventually virtual space will be exhausted. In current patch I simply put newly allocated block to the tail of a free list, thus reduce fragmentation, giving a chance to resolve allocation request using older blocks with possible holes left. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:48 +08:00
list_add_tail_rcu(&vb->free_list, &vbq->free);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
spin_unlock(&vbq->lock);
return vaddr;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
static void free_vmap_block(struct vmap_block *vb)
{
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
struct vmap_block *tmp;
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
struct xarray *xa;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
xa = addr_to_vb_xa(vb->va->va_start);
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
tmp = xa_erase(xa, addr_to_vb_idx(vb->va->va_start));
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
BUG_ON(tmp != vb);
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
vn = addr_to_node(vb->va->va_start);
spin_lock(&vn->busy.lock);
unlink_va(vb->va, &vn->busy.root);
spin_unlock(&vn->busy.lock);
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
vmalloc: eagerly clear ptes on vunmap On stock 2.6.37-rc4, running: # mount lilith:/export /mnt/lilith # find /mnt/lilith/ -type f -print0 | xargs -0 file crashes the machine fairly quickly under Xen. Often it results in oops messages, but the couple of times I tried just now, it just hung quietly and made Xen print some rude messages: (XEN) mm.c:2389:d80 Bad type (saw 7400000000000001 != exp 3000000000000000) for mfn 1d7058 (pfn 18fa7) (XEN) mm.c:964:d80 Attempt to create linear p.t. with write perms (XEN) mm.c:2389:d80 Bad type (saw 7400000000000010 != exp 1000000000000000) for mfn 1d2e04 (pfn 1d1fb) (XEN) mm.c:2965:d80 Error while pinning mfn 1d2e04 Which means the domain tried to map a pagetable page RW, which would allow it to map arbitrary memory, so Xen stopped it. This is because vm_unmap_ram() left some pages mapped in the vmalloc area after NFS had finished with them, and those pages got recycled as pagetable pages while still having these RW aliases. Removing those mappings immediately removes the Xen-visible aliases, and so it has no problem with those pages being reused as pagetable pages. Deferring the TLB flush doesn't upset Xen because it can flush the TLB itself as needed to maintain its invariants. When unmapping a region in the vmalloc space, clear the ptes immediately. There's no point in deferring this because there's no amortization benefit. The TLBs are left dirty, and they are flushed lazily to amortize the cost of the IPIs. This specific motivation for this patch is an oops-causing regression since 2.6.36 when using NFS under Xen, triggered by the NFS client's use of vm_map_ram() introduced in 56e4ebf877b60 ("NFS: readdir with vmapped pages") . XFS also uses vm_map_ram() and could cause similar problems. Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Nick Piggin <npiggin@kernel.dk> Cc: Bryan Schumaker <bjschuma@netapp.com> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: Alex Elder <aelder@sgi.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-12-03 06:31:18 +08:00
free_vmap_area_noflush(vb->va);
kfree_rcu(vb, rcu_head);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
static bool purge_fragmented_block(struct vmap_block *vb,
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
struct vmap_block_queue *vbq, struct list_head *purge_list,
bool force_purge)
{
if (vb->free + vb->dirty != VMAP_BBMAP_BITS ||
vb->dirty == VMAP_BBMAP_BITS)
return false;
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
/* Don't overeagerly purge usable blocks unless requested */
if (!(force_purge || vb->free < VMAP_PURGE_THRESHOLD))
return false;
/* prevent further allocs after releasing lock */
WRITE_ONCE(vb->free, 0);
/* prevent purging it again */
WRITE_ONCE(vb->dirty, VMAP_BBMAP_BITS);
vb->dirty_min = 0;
vb->dirty_max = VMAP_BBMAP_BITS;
spin_lock(&vbq->lock);
list_del_rcu(&vb->free_list);
spin_unlock(&vbq->lock);
list_add_tail(&vb->purge, purge_list);
return true;
}
static void free_purged_blocks(struct list_head *purge_list)
{
struct vmap_block *vb, *n_vb;
list_for_each_entry_safe(vb, n_vb, purge_list, purge) {
list_del(&vb->purge);
free_vmap_block(vb);
}
}
static void purge_fragmented_blocks(int cpu)
{
LIST_HEAD(purge);
struct vmap_block *vb;
struct vmap_block_queue *vbq = &per_cpu(vmap_block_queue, cpu);
rcu_read_lock();
list_for_each_entry_rcu(vb, &vbq->free, free_list) {
unsigned long free = READ_ONCE(vb->free);
unsigned long dirty = READ_ONCE(vb->dirty);
if (free + dirty != VMAP_BBMAP_BITS ||
dirty == VMAP_BBMAP_BITS)
continue;
spin_lock(&vb->lock);
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
purge_fragmented_block(vb, vbq, &purge, true);
spin_unlock(&vb->lock);
}
rcu_read_unlock();
free_purged_blocks(&purge);
}
static void purge_fragmented_blocks_allcpus(void)
{
int cpu;
for_each_possible_cpu(cpu)
purge_fragmented_blocks(cpu);
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
static void *vb_alloc(unsigned long size, gfp_t gfp_mask)
{
struct vmap_block_queue *vbq;
struct vmap_block *vb;
void *vaddr = NULL;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
unsigned int order;
BUG_ON(offset_in_page(size));
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
BUG_ON(size > PAGE_SIZE*VMAP_MAX_ALLOC);
if (WARN_ON(size == 0)) {
/*
* Allocating 0 bytes isn't what caller wants since
* get_order(0) returns funny result. Just warn and terminate
* early.
*/
return NULL;
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
order = get_order(size);
rcu_read_lock();
vbq = raw_cpu_ptr(&vmap_block_queue);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
list_for_each_entry_rcu(vb, &vbq->free, free_list) {
unsigned long pages_off;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (READ_ONCE(vb->free) < (1UL << order))
continue;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
spin_lock(&vb->lock);
if (vb->free < (1UL << order)) {
spin_unlock(&vb->lock);
continue;
}
pages_off = VMAP_BBMAP_BITS - vb->free;
vaddr = vmap_block_vaddr(vb->va->va_start, pages_off);
WRITE_ONCE(vb->free, vb->free - (1UL << order));
mm/vmalloc.c: add used_map into vmap_block to track space of vmap_block Patch series "mm/vmalloc.c: allow vread() to read out vm_map_ram areas", v5. Problem: *** Stephen reported vread() will skip vm_map_ram areas when reading out /proc/kcore with drgn utility. Please see below link to get more details. /proc/kcore reads 0's for vmap_block https://lore.kernel.org/all/87ilk6gos2.fsf@oracle.com/T/#u Root cause: *** The normal vmalloc API uses struct vmap_area to manage the virtual kernel area allocated, and associate a vm_struct to store more information and pass out. However, area reserved through vm_map_ram() interface doesn't allocate vm_struct to associate with. So the current code in vread() will skip the vm_map_ram area through 'if (!va->vm)' conditional checking. Solution: *** To mark the area reserved through vm_map_ram() interface, add field 'flags' into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). And also add bitmap field 'used_map' into struct vmap_block to mark those further subdivided regions being used to differentiate with dirty and free regions in vmap_block. With the help of above vmap_area->flags and vmap_block->used_map, we can recognize and handle vm_map_ram areas successfully. All these are done in patch 1~3. Meanwhile, do some improvement on areas related to vm_map_ram areas in patch 4, 5. And also change area flag from VM_ALLOC to VM_IOREMAP in patch 6, 7 because this will show them as 'ioremap' in /proc/vmallocinfo, and exclude them from /proc/kcore. This patch (of 7): In one vmap_block area, there could be three types of regions: region being used which is allocated through vb_alloc(), dirty region which is freed via vb_free() and free region. Among them, only used region has available data. While there's no way to track those used regions currently. Here, add bitmap field used_map into vmap_block, and set/clear it during allocation or freeing regions of vmap_block area. This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-1-bhe@redhat.com Link: https://lkml.kernel.org/r/20230206084020.174506-2-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:14 +08:00
bitmap_set(vb->used_map, pages_off, (1UL << order));
if (vb->free == 0) {
spin_lock(&vbq->lock);
list_del_rcu(&vb->free_list);
spin_unlock(&vbq->lock);
}
spin_unlock(&vb->lock);
break;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
rcu_read_unlock();
/* Allocate new block if nothing was found */
if (!vaddr)
vaddr = new_vmap_block(order, gfp_mask);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
return vaddr;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
mm: pass addr as unsigned long to vb_free Ever use of addr in vb_free casts to unsigned long first, and the caller has an unsigned long version of the address available anyway. Just pass that and avoid all the casts. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-13-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:02 +08:00
static void vb_free(unsigned long addr, unsigned long size)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
unsigned long offset;
unsigned int order;
struct vmap_block *vb;
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
struct xarray *xa;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
BUG_ON(offset_in_page(size));
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
BUG_ON(size > PAGE_SIZE*VMAP_MAX_ALLOC);
mm: pass addr as unsigned long to vb_free Ever use of addr in vb_free casts to unsigned long first, and the caller has an unsigned long version of the address available anyway. Just pass that and avoid all the casts. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-13-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:02 +08:00
flush_cache_vunmap(addr, addr + size);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
order = get_order(size);
mm: pass addr as unsigned long to vb_free Ever use of addr in vb_free casts to unsigned long first, and the caller has an unsigned long version of the address available anyway. Just pass that and avoid all the casts. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-13-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:02 +08:00
offset = (addr & (VMAP_BLOCK_SIZE - 1)) >> PAGE_SHIFT;
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
xa = addr_to_vb_xa(addr);
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
vb = xa_load(xa, addr_to_vb_idx(addr));
mm/vmalloc.c: add used_map into vmap_block to track space of vmap_block Patch series "mm/vmalloc.c: allow vread() to read out vm_map_ram areas", v5. Problem: *** Stephen reported vread() will skip vm_map_ram areas when reading out /proc/kcore with drgn utility. Please see below link to get more details. /proc/kcore reads 0's for vmap_block https://lore.kernel.org/all/87ilk6gos2.fsf@oracle.com/T/#u Root cause: *** The normal vmalloc API uses struct vmap_area to manage the virtual kernel area allocated, and associate a vm_struct to store more information and pass out. However, area reserved through vm_map_ram() interface doesn't allocate vm_struct to associate with. So the current code in vread() will skip the vm_map_ram area through 'if (!va->vm)' conditional checking. Solution: *** To mark the area reserved through vm_map_ram() interface, add field 'flags' into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). And also add bitmap field 'used_map' into struct vmap_block to mark those further subdivided regions being used to differentiate with dirty and free regions in vmap_block. With the help of above vmap_area->flags and vmap_block->used_map, we can recognize and handle vm_map_ram areas successfully. All these are done in patch 1~3. Meanwhile, do some improvement on areas related to vm_map_ram areas in patch 4, 5. And also change area flag from VM_ALLOC to VM_IOREMAP in patch 6, 7 because this will show them as 'ioremap' in /proc/vmallocinfo, and exclude them from /proc/kcore. This patch (of 7): In one vmap_block area, there could be three types of regions: region being used which is allocated through vb_alloc(), dirty region which is freed via vb_free() and free region. Among them, only used region has available data. While there's no way to track those used regions currently. Here, add bitmap field used_map into vmap_block, and set/clear it during allocation or freeing regions of vmap_block area. This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-1-bhe@redhat.com Link: https://lkml.kernel.org/r/20230206084020.174506-2-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:14 +08:00
spin_lock(&vb->lock);
bitmap_clear(vb->used_map, offset, (1UL << order));
spin_unlock(&vb->lock);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
vunmap_range_noflush(addr, addr + size);
vmalloc: eagerly clear ptes on vunmap On stock 2.6.37-rc4, running: # mount lilith:/export /mnt/lilith # find /mnt/lilith/ -type f -print0 | xargs -0 file crashes the machine fairly quickly under Xen. Often it results in oops messages, but the couple of times I tried just now, it just hung quietly and made Xen print some rude messages: (XEN) mm.c:2389:d80 Bad type (saw 7400000000000001 != exp 3000000000000000) for mfn 1d7058 (pfn 18fa7) (XEN) mm.c:964:d80 Attempt to create linear p.t. with write perms (XEN) mm.c:2389:d80 Bad type (saw 7400000000000010 != exp 1000000000000000) for mfn 1d2e04 (pfn 1d1fb) (XEN) mm.c:2965:d80 Error while pinning mfn 1d2e04 Which means the domain tried to map a pagetable page RW, which would allow it to map arbitrary memory, so Xen stopped it. This is because vm_unmap_ram() left some pages mapped in the vmalloc area after NFS had finished with them, and those pages got recycled as pagetable pages while still having these RW aliases. Removing those mappings immediately removes the Xen-visible aliases, and so it has no problem with those pages being reused as pagetable pages. Deferring the TLB flush doesn't upset Xen because it can flush the TLB itself as needed to maintain its invariants. When unmapping a region in the vmalloc space, clear the ptes immediately. There's no point in deferring this because there's no amortization benefit. The TLBs are left dirty, and they are flushed lazily to amortize the cost of the IPIs. This specific motivation for this patch is an oops-causing regression since 2.6.36 when using NFS under Xen, triggered by the NFS client's use of vm_map_ram() introduced in 56e4ebf877b60 ("NFS: readdir with vmapped pages") . XFS also uses vm_map_ram() and could cause similar problems. Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Nick Piggin <npiggin@kernel.dk> Cc: Bryan Schumaker <bjschuma@netapp.com> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: Alex Elder <aelder@sgi.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-12-03 06:31:18 +08:00
mm, debug_pagealloc: don't rely on static keys too early Commit 96a2b03f281d ("mm, debug_pagelloc: use static keys to enable debugging") has introduced a static key to reduce overhead when debug_pagealloc is compiled in but not enabled. It relied on the assumption that jump_label_init() is called before parse_early_param() as in start_kernel(), so when the "debug_pagealloc=on" option is parsed, it is safe to enable the static key. However, it turns out multiple architectures call parse_early_param() earlier from their setup_arch(). x86 also calls jump_label_init() even earlier, so no issue was found while testing the commit, but same is not true for e.g. ppc64 and s390 where the kernel would not boot with debug_pagealloc=on as found by our QA. To fix this without tricky changes to init code of multiple architectures, this patch partially reverts the static key conversion from 96a2b03f281d. Init-time and non-fastpath calls (such as in arch code) of debug_pagealloc_enabled() will again test a simple bool variable. Fastpath mm code is converted to a new debug_pagealloc_enabled_static() variant that relies on the static key, which is enabled in a well-defined point in mm_init() where it's guaranteed that jump_label_init() has been called, regardless of architecture. [sfr@canb.auug.org.au: export _debug_pagealloc_enabled_early] Link: http://lkml.kernel.org/r/20200106164944.063ac07b@canb.auug.org.au Link: http://lkml.kernel.org/r/20191219130612.23171-1-vbabka@suse.cz Fixes: 96a2b03f281d ("mm, debug_pagelloc: use static keys to enable debugging") Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Qian Cai <cai@lca.pw> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-01-14 08:29:20 +08:00
if (debug_pagealloc_enabled_static())
mm: pass addr as unsigned long to vb_free Ever use of addr in vb_free casts to unsigned long first, and the caller has an unsigned long version of the address available anyway. Just pass that and avoid all the casts. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-13-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:02 +08:00
flush_tlb_kernel_range(addr, addr + size);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
spin_lock(&vb->lock);
mm/vmalloc: get rid of dirty bitmap inside vmap_block structure In original implementation of vm_map_ram made by Nick Piggin there were two bitmaps: alloc_map and dirty_map. None of them were used as supposed to be: finding a suitable free hole for next allocation in block. vm_map_ram allocates space sequentially in block and on free call marks pages as dirty, so freed space can't be reused anymore. Actually it would be very interesting to know the real meaning of those bitmaps, maybe implementation was incomplete, etc. But long time ago Zhang Yanfei removed alloc_map by these two commits: mm/vmalloc.c: remove dead code in vb_alloc 3fcd76e8028e0be37b02a2002b4f56755daeda06 mm/vmalloc.c: remove alloc_map from vmap_block b8e748b6c32999f221ea4786557b8e7e6c4e4e7a In this patch I replaced dirty_map with two range variables: dirty min and max. These variables store minimum and maximum position of dirty space in a block, since we need only to know the dirty range, not exact position of dirty pages. Why it was made? Several reasons: at first glance it seems that vm_map_ram allocator concerns about fragmentation thus it uses bitmaps for finding free hole, but it is not true. To avoid complexity seems it is better to use something simple, like min or max range values. Secondly, code also becomes simpler, without iteration over bitmap, just comparing values in min and max macros. Thirdly, bitmap occupies up to 1024 bits (4MB is a max size of a block). Here I replaced the whole bitmap with two longs. Finally vm_unmap_aliases should be slightly faster and the whole vmap_block structure occupies less memory. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:55 +08:00
/* Expand the not yet TLB flushed dirty range */
mm/vmalloc: get rid of dirty bitmap inside vmap_block structure In original implementation of vm_map_ram made by Nick Piggin there were two bitmaps: alloc_map and dirty_map. None of them were used as supposed to be: finding a suitable free hole for next allocation in block. vm_map_ram allocates space sequentially in block and on free call marks pages as dirty, so freed space can't be reused anymore. Actually it would be very interesting to know the real meaning of those bitmaps, maybe implementation was incomplete, etc. But long time ago Zhang Yanfei removed alloc_map by these two commits: mm/vmalloc.c: remove dead code in vb_alloc 3fcd76e8028e0be37b02a2002b4f56755daeda06 mm/vmalloc.c: remove alloc_map from vmap_block b8e748b6c32999f221ea4786557b8e7e6c4e4e7a In this patch I replaced dirty_map with two range variables: dirty min and max. These variables store minimum and maximum position of dirty space in a block, since we need only to know the dirty range, not exact position of dirty pages. Why it was made? Several reasons: at first glance it seems that vm_map_ram allocator concerns about fragmentation thus it uses bitmaps for finding free hole, but it is not true. To avoid complexity seems it is better to use something simple, like min or max range values. Secondly, code also becomes simpler, without iteration over bitmap, just comparing values in min and max macros. Thirdly, bitmap occupies up to 1024 bits (4MB is a max size of a block). Here I replaced the whole bitmap with two longs. Finally vm_unmap_aliases should be slightly faster and the whole vmap_block structure occupies less memory. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:55 +08:00
vb->dirty_min = min(vb->dirty_min, offset);
vb->dirty_max = max(vb->dirty_max, offset + (1UL << order));
WRITE_ONCE(vb->dirty, vb->dirty + (1UL << order));
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (vb->dirty == VMAP_BBMAP_BITS) {
BUG_ON(vb->free);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
spin_unlock(&vb->lock);
free_vmap_block(vb);
} else
spin_unlock(&vb->lock);
}
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
static void _vm_unmap_aliases(unsigned long start, unsigned long end, int flush)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
LIST_HEAD(purge_list);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
int cpu;
if (unlikely(!vmap_initialized))
return;
mutex_lock(&vmap_purge_lock);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
for_each_possible_cpu(cpu) {
struct vmap_block_queue *vbq = &per_cpu(vmap_block_queue, cpu);
struct vmap_block *vb;
mm/vmalloc: prevent stale TLBs in fully utilized blocks Patch series "mm/vmalloc: Assorted fixes and improvements", v2. this series addresses the following issues: 1) Prevent the stale TLB problem related to fully utilized vmap blocks 2) Avoid the double per CPU list walk in _vm_unmap_aliases() 3) Avoid flushing dirty space over and over 4) Add a lockless quickcheck in vb_alloc() and add missing READ/WRITE_ONCE() annotations 5) Prevent overeager purging of usable vmap_blocks if not under memory/address space pressure. This patch (of 6): _vm_unmap_aliases() is used to ensure that no unflushed TLB entries for a page are left in the system. This is required due to the lazy TLB flush mechanism in vmalloc. This is tried to achieve by walking the per CPU free lists, but those do not contain fully utilized vmap blocks because they are removed from the free list once the blocks free space became zero. When the block is not fully unmapped then it is not on the purge list either. So neither the per CPU list iteration nor the purge list walk find the block and if the page was mapped via such a block and the TLB has not yet been flushed, the guarantee of _vm_unmap_aliases() that there are no stale TLBs after returning is broken: x = vb_alloc() // Removes vmap_block from free list because vb->free became 0 vb_free(x) // Unmaps page and marks in dirty_min/max range // Block has still mappings and is not put on purge list // Page is reused vm_unmap_aliases() // Can't find vmap block with the dirty space -> FAIL So instead of walking the per CPU free lists, walk the per CPU xarrays which hold pointers to _all_ active blocks in the system including those removed from the free lists. Link: https://lkml.kernel.org/r/20230525122342.109672430@linutronix.de Link: https://lkml.kernel.org/r/20230525124504.573987880@linutronix.de Fixes: db64fe02258f ("mm: rewrite vmap layer") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:03 +08:00
unsigned long idx;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
rcu_read_lock();
mm/vmalloc: prevent stale TLBs in fully utilized blocks Patch series "mm/vmalloc: Assorted fixes and improvements", v2. this series addresses the following issues: 1) Prevent the stale TLB problem related to fully utilized vmap blocks 2) Avoid the double per CPU list walk in _vm_unmap_aliases() 3) Avoid flushing dirty space over and over 4) Add a lockless quickcheck in vb_alloc() and add missing READ/WRITE_ONCE() annotations 5) Prevent overeager purging of usable vmap_blocks if not under memory/address space pressure. This patch (of 6): _vm_unmap_aliases() is used to ensure that no unflushed TLB entries for a page are left in the system. This is required due to the lazy TLB flush mechanism in vmalloc. This is tried to achieve by walking the per CPU free lists, but those do not contain fully utilized vmap blocks because they are removed from the free list once the blocks free space became zero. When the block is not fully unmapped then it is not on the purge list either. So neither the per CPU list iteration nor the purge list walk find the block and if the page was mapped via such a block and the TLB has not yet been flushed, the guarantee of _vm_unmap_aliases() that there are no stale TLBs after returning is broken: x = vb_alloc() // Removes vmap_block from free list because vb->free became 0 vb_free(x) // Unmaps page and marks in dirty_min/max range // Block has still mappings and is not put on purge list // Page is reused vm_unmap_aliases() // Can't find vmap block with the dirty space -> FAIL So instead of walking the per CPU free lists, walk the per CPU xarrays which hold pointers to _all_ active blocks in the system including those removed from the free lists. Link: https://lkml.kernel.org/r/20230525122342.109672430@linutronix.de Link: https://lkml.kernel.org/r/20230525124504.573987880@linutronix.de Fixes: db64fe02258f ("mm: rewrite vmap layer") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:03 +08:00
xa_for_each(&vbq->vmap_blocks, idx, vb) {
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
spin_lock(&vb->lock);
/*
* Try to purge a fragmented block first. If it's
* not purgeable, check whether there is dirty
* space to be flushed.
*/
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
if (!purge_fragmented_block(vb, vbq, &purge_list, false) &&
vb->dirty_max && vb->dirty != VMAP_BBMAP_BITS) {
mm/vmalloc: get rid of dirty bitmap inside vmap_block structure In original implementation of vm_map_ram made by Nick Piggin there were two bitmaps: alloc_map and dirty_map. None of them were used as supposed to be: finding a suitable free hole for next allocation in block. vm_map_ram allocates space sequentially in block and on free call marks pages as dirty, so freed space can't be reused anymore. Actually it would be very interesting to know the real meaning of those bitmaps, maybe implementation was incomplete, etc. But long time ago Zhang Yanfei removed alloc_map by these two commits: mm/vmalloc.c: remove dead code in vb_alloc 3fcd76e8028e0be37b02a2002b4f56755daeda06 mm/vmalloc.c: remove alloc_map from vmap_block b8e748b6c32999f221ea4786557b8e7e6c4e4e7a In this patch I replaced dirty_map with two range variables: dirty min and max. These variables store minimum and maximum position of dirty space in a block, since we need only to know the dirty range, not exact position of dirty pages. Why it was made? Several reasons: at first glance it seems that vm_map_ram allocator concerns about fragmentation thus it uses bitmaps for finding free hole, but it is not true. To avoid complexity seems it is better to use something simple, like min or max range values. Secondly, code also becomes simpler, without iteration over bitmap, just comparing values in min and max macros. Thirdly, bitmap occupies up to 1024 bits (4MB is a max size of a block). Here I replaced the whole bitmap with two longs. Finally vm_unmap_aliases should be slightly faster and the whole vmap_block structure occupies less memory. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:55 +08:00
unsigned long va_start = vb->va->va_start;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
unsigned long s, e;
mm/vmalloc: get rid of dirty bitmap inside vmap_block structure In original implementation of vm_map_ram made by Nick Piggin there were two bitmaps: alloc_map and dirty_map. None of them were used as supposed to be: finding a suitable free hole for next allocation in block. vm_map_ram allocates space sequentially in block and on free call marks pages as dirty, so freed space can't be reused anymore. Actually it would be very interesting to know the real meaning of those bitmaps, maybe implementation was incomplete, etc. But long time ago Zhang Yanfei removed alloc_map by these two commits: mm/vmalloc.c: remove dead code in vb_alloc 3fcd76e8028e0be37b02a2002b4f56755daeda06 mm/vmalloc.c: remove alloc_map from vmap_block b8e748b6c32999f221ea4786557b8e7e6c4e4e7a In this patch I replaced dirty_map with two range variables: dirty min and max. These variables store minimum and maximum position of dirty space in a block, since we need only to know the dirty range, not exact position of dirty pages. Why it was made? Several reasons: at first glance it seems that vm_map_ram allocator concerns about fragmentation thus it uses bitmaps for finding free hole, but it is not true. To avoid complexity seems it is better to use something simple, like min or max range values. Secondly, code also becomes simpler, without iteration over bitmap, just comparing values in min and max macros. Thirdly, bitmap occupies up to 1024 bits (4MB is a max size of a block). Here I replaced the whole bitmap with two longs. Finally vm_unmap_aliases should be slightly faster and the whole vmap_block structure occupies less memory. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:55 +08:00
s = va_start + (vb->dirty_min << PAGE_SHIFT);
e = va_start + (vb->dirty_max << PAGE_SHIFT);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
mm/vmalloc: get rid of dirty bitmap inside vmap_block structure In original implementation of vm_map_ram made by Nick Piggin there were two bitmaps: alloc_map and dirty_map. None of them were used as supposed to be: finding a suitable free hole for next allocation in block. vm_map_ram allocates space sequentially in block and on free call marks pages as dirty, so freed space can't be reused anymore. Actually it would be very interesting to know the real meaning of those bitmaps, maybe implementation was incomplete, etc. But long time ago Zhang Yanfei removed alloc_map by these two commits: mm/vmalloc.c: remove dead code in vb_alloc 3fcd76e8028e0be37b02a2002b4f56755daeda06 mm/vmalloc.c: remove alloc_map from vmap_block b8e748b6c32999f221ea4786557b8e7e6c4e4e7a In this patch I replaced dirty_map with two range variables: dirty min and max. These variables store minimum and maximum position of dirty space in a block, since we need only to know the dirty range, not exact position of dirty pages. Why it was made? Several reasons: at first glance it seems that vm_map_ram allocator concerns about fragmentation thus it uses bitmaps for finding free hole, but it is not true. To avoid complexity seems it is better to use something simple, like min or max range values. Secondly, code also becomes simpler, without iteration over bitmap, just comparing values in min and max macros. Thirdly, bitmap occupies up to 1024 bits (4MB is a max size of a block). Here I replaced the whole bitmap with two longs. Finally vm_unmap_aliases should be slightly faster and the whole vmap_block structure occupies less memory. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:55 +08:00
start = min(s, start);
end = max(e, end);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
/* Prevent that this is flushed again */
vb->dirty_min = VMAP_BBMAP_BITS;
vb->dirty_max = 0;
mm/vmalloc: get rid of dirty bitmap inside vmap_block structure In original implementation of vm_map_ram made by Nick Piggin there were two bitmaps: alloc_map and dirty_map. None of them were used as supposed to be: finding a suitable free hole for next allocation in block. vm_map_ram allocates space sequentially in block and on free call marks pages as dirty, so freed space can't be reused anymore. Actually it would be very interesting to know the real meaning of those bitmaps, maybe implementation was incomplete, etc. But long time ago Zhang Yanfei removed alloc_map by these two commits: mm/vmalloc.c: remove dead code in vb_alloc 3fcd76e8028e0be37b02a2002b4f56755daeda06 mm/vmalloc.c: remove alloc_map from vmap_block b8e748b6c32999f221ea4786557b8e7e6c4e4e7a In this patch I replaced dirty_map with two range variables: dirty min and max. These variables store minimum and maximum position of dirty space in a block, since we need only to know the dirty range, not exact position of dirty pages. Why it was made? Several reasons: at first glance it seems that vm_map_ram allocator concerns about fragmentation thus it uses bitmaps for finding free hole, but it is not true. To avoid complexity seems it is better to use something simple, like min or max range values. Secondly, code also becomes simpler, without iteration over bitmap, just comparing values in min and max macros. Thirdly, bitmap occupies up to 1024 bits (4MB is a max size of a block). Here I replaced the whole bitmap with two longs. Finally vm_unmap_aliases should be slightly faster and the whole vmap_block structure occupies less memory. Signed-off-by: Roman Pen <r.peniaev@gmail.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: WANG Chao <chaowang@redhat.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christoph Lameter <cl@linux.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: Rob Jones <rob.jones@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-16 07:13:55 +08:00
flush = 1;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
spin_unlock(&vb->lock);
}
rcu_read_unlock();
}
free_purged_blocks(&purge_list);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (!__purge_vmap_area_lazy(start, end, false) && flush)
flush_tlb_kernel_range(start, end);
mutex_unlock(&vmap_purge_lock);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
/**
* vm_unmap_aliases - unmap outstanding lazy aliases in the vmap layer
*
* The vmap/vmalloc layer lazily flushes kernel virtual mappings primarily
* to amortize TLB flushing overheads. What this means is that any page you
* have now, may, in a former life, have been mapped into kernel virtual
* address by the vmap layer and so there might be some CPUs with TLB entries
* still referencing that page (additional to the regular 1:1 kernel mapping).
*
* vm_unmap_aliases flushes all such lazy mappings. After it returns, we can
* be sure that none of the pages we have control over will have any aliases
* from the vmap layer.
*/
void vm_unmap_aliases(void)
{
unsigned long start = ULONG_MAX, end = 0;
int flush = 0;
_vm_unmap_aliases(start, end, flush);
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
EXPORT_SYMBOL_GPL(vm_unmap_aliases);
/**
* vm_unmap_ram - unmap linear kernel address space set up by vm_map_ram
* @mem: the pointer returned by vm_map_ram
* @count: the count passed to that vm_map_ram call (cannot unmap partial)
*/
void vm_unmap_ram(const void *mem, unsigned int count)
{
unsigned long size = (unsigned long)count << PAGE_SHIFT;
unsigned long addr = (unsigned long)kasan_reset_tag(mem);
struct vmap_area *va;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
might_sleep();
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
BUG_ON(!addr);
BUG_ON(addr < VMALLOC_START);
BUG_ON(addr > VMALLOC_END);
BUG_ON(!PAGE_ALIGNED(addr));
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
kasan_poison_vmalloc(mem, size);
if (likely(count <= VMAP_MAX_ALLOC)) {
debug_check_no_locks_freed(mem, size);
mm: pass addr as unsigned long to vb_free Ever use of addr in vb_free casts to unsigned long first, and the caller has an unsigned long version of the address available anyway. Just pass that and avoid all the casts. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-13-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:02 +08:00
vb_free(addr, size);
return;
}
mm: vmalloc: avoid calling __find_vmap_area() twice in __vunmap() Currently the __vunmap() path calls __find_vmap_area() twice. Once on entry to check that the area exists, then inside the remove_vm_area() function which also performs a new search for the VA. In order to improvie it from a performance point of view we split remove_vm_area() into two new parts: - find_unlink_vmap_area() that does a search and unlink from tree; - __remove_vm_area() that removes without searching. In this case there is no any functional change for remove_vm_area() whereas vm_remove_mappings(), where a second search happens, switches to the __remove_vm_area() variant where the already detached VA is passed as a parameter, so there is no need to find it again. Performance wise, i use test_vmalloc.sh with 32 threads doing alloc free on a 64-CPUs-x86_64-box: perf without this patch: - 31.41% 0.50% vmalloc_test/10 [kernel.vmlinux] [k] __vunmap - 30.92% __vunmap - 17.67% _raw_spin_lock native_queued_spin_lock_slowpath - 12.33% remove_vm_area - 11.79% free_vmap_area_noflush - 11.18% _raw_spin_lock native_queued_spin_lock_slowpath 0.76% free_unref_page perf with this patch: - 11.35% 0.13% vmalloc_test/14 [kernel.vmlinux] [k] __vunmap - 11.23% __vunmap - 8.28% find_unlink_vmap_area - 7.95% _raw_spin_lock 7.44% native_queued_spin_lock_slowpath - 1.93% free_vmap_area_noflush - 0.56% _raw_spin_lock 0.53% native_queued_spin_lock_slowpath 0.60% __vunmap_range_noflush __vunmap() consumes around ~20% less CPU cycles on this test. Also, switch from find_vmap_area() to find_unlink_vmap_area() to prevent a double access to the vmap_area_lock: one for finding area, second time is for unlinking from a tree. [urezki@gmail.com: switch to find_unlink_vmap_area() in vm_unmap_ram()] Link: https://lkml.kernel.org/r/20221222190022.134380-2-urezki@gmail.com Link: https://lkml.kernel.org/r/20221222190022.134380-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 03:00:20 +08:00
va = find_unlink_vmap_area(addr);
if (WARN_ON_ONCE(!va))
return;
debug_check_no_locks_freed((void *)va->va_start,
(va->va_end - va->va_start));
free_unmap_vmap_area(va);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
}
EXPORT_SYMBOL(vm_unmap_ram);
/**
* vm_map_ram - map pages linearly into kernel virtual address (vmalloc space)
* @pages: an array of pointers to the pages to be mapped
* @count: number of pages
* @node: prefer to allocate data structures on this node
*
mm/vmalloc.c: enhance vm_map_ram() comment vm_map_ram() has a fragmentation problem when it cannot purge a chunk(ie, 4M address space) if there is a pinning object in that addresss space. So it could consume all VMALLOC address space easily. We can fix the fragmentation problem by using vmap instead of vm_map_ram() but vmap() is known to be slow compared to vm_map_ram(). Minchan said vm_map_ram is 5 times faster than vmap in his tests. So I thought we should fix fragment problem of vm_map_ram because our proprietary GPU driver has used it heavily. On second thought, it's not an easy because we should reuse freed space for solving the problem and it could make more IPI and bitmap operation for searching hole. It could mitigate API's goal which is very fast mapping. And even fragmentation problem wouldn't show in 64 bit machine. Another option is that the user should separate long-life and short-life object and use vmap for long-life but vm_map_ram for short-life. If we inform the user about the characteristic of vm_map_ram the user can choose one according to the page lifetime. Let's add some notice messages to user. [akpm@linux-foundation.org: tweak comment text] Signed-off-by: Gioh Kim <gioh.kim@lge.com> Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-04-08 06:37:37 +08:00
* If you use this function for less than VMAP_MAX_ALLOC pages, it could be
* faster than vmap so it's good. But if you mix long-life and short-life
* objects with vm_map_ram(), it could consume lots of address space through
* fragmentation (especially on a 32bit machine). You could see failures in
* the end. Please use this function for short-lived objects.
*
* Returns: a pointer to the address that has been mapped, or %NULL on failure
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
*/
2020-06-02 12:51:27 +08:00
void *vm_map_ram(struct page **pages, unsigned int count, int node)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
unsigned long size = (unsigned long)count << PAGE_SHIFT;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
unsigned long addr;
void *mem;
if (likely(count <= VMAP_MAX_ALLOC)) {
mem = vb_alloc(size, GFP_KERNEL);
if (IS_ERR(mem))
return NULL;
addr = (unsigned long)mem;
} else {
struct vmap_area *va;
va = alloc_vmap_area(size, PAGE_SIZE,
mm/vmalloc.c: add flags to mark vm_map_ram area Through vmalloc API, a virtual kernel area is reserved for physical address mapping. And vmap_area is used to track them, while vm_struct is allocated to associate with the vmap_area to store more information and passed out. However, area reserved via vm_map_ram() is an exception. It doesn't have vm_struct to associate with vmap_area. And we can't recognize the vmap_area with '->vm == NULL' as a vm_map_ram() area because the normal freeing path will set va->vm = NULL before unmapping, please see function remove_vm_area(). Meanwhile, there are two kinds of handling for vm_map_ram area. One is the whole vmap_area being reserved and mapped at one time through vm_map_area() interface; the other is the whole vmap_area with VMAP_BLOCK_SIZE size being reserved, while mapped into split regions with smaller size via vb_alloc(). To mark the area reserved through vm_map_ram(), add flags field into struct vmap_area. Bit 0 indicates this is vm_map_ram area created through vm_map_ram() interface, while bit 1 marks out the type of vm_map_ram area which makes use of vmap_block to manage split regions via vb_alloc/free(). This is a preparation for later use. Link: https://lkml.kernel.org/r/20230206084020.174506-3-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Dan Carpenter <error27@gmail.com> Cc: Stephen Brennan <stephen.s.brennan@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-02-06 16:40:15 +08:00
VMALLOC_START, VMALLOC_END,
mm/vmalloc: eliminated the lock contention from twice to once When allocating a new memory area where the mapping address range is known, it is observed that the vmap_node->busy.lock is acquired twice. The first acquisition occurs in the alloc_vmap_area() function when inserting the vm area into the vm mapping red-black tree. The second acquisition occurs in the setup_vmalloc_vm() function when updating the properties of the vm, such as flags and address, etc. Combine these two operations together in alloc_vmap_area(), which improves scalability when the vmap_node->busy.lock is contended. By doing so, the need to acquire the lock twice can also be eliminated to once. With the above change, tested on intel sapphire rapids platform(224 vcpu), a 4% performance improvement is gained on stress-ng/pthread(https://github.com/ColinIanKing/stress-ng), which is the stress test of thread creations. Link: https://lkml.kernel.org/r/20240307021440.64967-1-rulin.huang@intel.com Co-developed-by: "Chen, Tim C" <tim.c.chen@intel.com> Signed-off-by: "Chen, Tim C" <tim.c.chen@intel.com> Co-developed-by: "King, Colin" <colin.king@intel.com> Signed-off-by: "King, Colin" <colin.king@intel.com> Signed-off-by: rulinhuang <rulin.huang@intel.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Wangyang Guo <wangyang.guo@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-07 10:14:40 +08:00
node, GFP_KERNEL, VMAP_RAM,
NULL);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (IS_ERR(va))
return NULL;
addr = va->va_start;
mem = (void *)addr;
}
if (vmap_pages_range(addr, addr + size, PAGE_KERNEL,
pages, PAGE_SHIFT) < 0) {
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
vm_unmap_ram(mem, count);
return NULL;
}
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
/*
* Mark the pages as accessible, now that they are mapped.
* With hardware tag-based KASAN, marking is skipped for
* non-VM_ALLOC mappings, see __kasan_unpoison_vmalloc().
*/
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
mem = kasan_unpoison_vmalloc(mem, size, KASAN_VMALLOC_PROT_NORMAL);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
return mem;
}
EXPORT_SYMBOL(vm_map_ram);
static struct vm_struct *vmlist __initdata;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
static inline unsigned int vm_area_page_order(struct vm_struct *vm)
{
#ifdef CONFIG_HAVE_ARCH_HUGE_VMALLOC
return vm->page_order;
#else
return 0;
#endif
}
static inline void set_vm_area_page_order(struct vm_struct *vm, unsigned int order)
{
#ifdef CONFIG_HAVE_ARCH_HUGE_VMALLOC
vm->page_order = order;
#else
BUG_ON(order != 0);
#endif
}
/**
* vm_area_add_early - add vmap area early during boot
* @vm: vm_struct to add
*
* This function is used to add fixed kernel vm area to vmlist before
* vmalloc_init() is called. @vm->addr, @vm->size, and @vm->flags
* should contain proper values and the other fields should be zero.
*
* DO NOT USE THIS FUNCTION UNLESS YOU KNOW WHAT YOU'RE DOING.
*/
void __init vm_area_add_early(struct vm_struct *vm)
{
struct vm_struct *tmp, **p;
BUG_ON(vmap_initialized);
for (p = &vmlist; (tmp = *p) != NULL; p = &tmp->next) {
if (tmp->addr >= vm->addr) {
BUG_ON(tmp->addr < vm->addr + vm->size);
break;
} else
BUG_ON(tmp->addr + tmp->size > vm->addr);
}
vm->next = *p;
*p = vm;
}
/**
* vm_area_register_early - register vmap area early during boot
* @vm: vm_struct to register
* @align: requested alignment
*
* This function is used to register kernel vm area before
* vmalloc_init() is called. @vm->size and @vm->flags should contain
* proper values on entry and other fields should be zero. On return,
* vm->addr contains the allocated address.
*
* DO NOT USE THIS FUNCTION UNLESS YOU KNOW WHAT YOU'RE DOING.
*/
void __init vm_area_register_early(struct vm_struct *vm, size_t align)
{
vmalloc: choose a better start address in vm_area_register_early() Percpu embedded first chunk allocator is the firstly option, but it could fail on ARM64, eg, percpu: max_distance=0x5fcfdc640000 too large for vmalloc space 0x781fefff0000 percpu: max_distance=0x600000540000 too large for vmalloc space 0x7dffb7ff0000 percpu: max_distance=0x5fff9adb0000 too large for vmalloc space 0x5dffb7ff0000 then we could get to WARNING: CPU: 15 PID: 461 at vmalloc.c:3087 pcpu_get_vm_areas+0x488/0x838 and the system cannot boot successfully. Let's implement page mapping percpu first chunk allocator as a fallback to the embedding allocator to increase the robustness of the system. Also fix a crash when both NEED_PER_CPU_PAGE_FIRST_CHUNK and KASAN_VMALLOC enabled. Tested on ARM64 qemu with cmdline "percpu_alloc=page". This patch (of 3): There are some fixed locations in the vmalloc area be reserved in ARM(see iotable_init()) and ARM64(see map_kernel()), but for pcpu_page_first_chunk(), it calls vm_area_register_early() and choose VMALLOC_START as the start address of vmap area which could be conflicted with above address, then could trigger a BUG_ON in vm_area_add_early(). Let's choose a suit start address by traversing the vmlist. Link: https://lkml.kernel.org/r/20210910053354.26721-1-wangkefeng.wang@huawei.com Link: https://lkml.kernel.org/r/20210910053354.26721-2-wangkefeng.wang@huawei.com Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Marco Elver <elver@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:41 +08:00
unsigned long addr = ALIGN(VMALLOC_START, align);
struct vm_struct *cur, **p;
vmalloc: choose a better start address in vm_area_register_early() Percpu embedded first chunk allocator is the firstly option, but it could fail on ARM64, eg, percpu: max_distance=0x5fcfdc640000 too large for vmalloc space 0x781fefff0000 percpu: max_distance=0x600000540000 too large for vmalloc space 0x7dffb7ff0000 percpu: max_distance=0x5fff9adb0000 too large for vmalloc space 0x5dffb7ff0000 then we could get to WARNING: CPU: 15 PID: 461 at vmalloc.c:3087 pcpu_get_vm_areas+0x488/0x838 and the system cannot boot successfully. Let's implement page mapping percpu first chunk allocator as a fallback to the embedding allocator to increase the robustness of the system. Also fix a crash when both NEED_PER_CPU_PAGE_FIRST_CHUNK and KASAN_VMALLOC enabled. Tested on ARM64 qemu with cmdline "percpu_alloc=page". This patch (of 3): There are some fixed locations in the vmalloc area be reserved in ARM(see iotable_init()) and ARM64(see map_kernel()), but for pcpu_page_first_chunk(), it calls vm_area_register_early() and choose VMALLOC_START as the start address of vmap area which could be conflicted with above address, then could trigger a BUG_ON in vm_area_add_early(). Let's choose a suit start address by traversing the vmlist. Link: https://lkml.kernel.org/r/20210910053354.26721-1-wangkefeng.wang@huawei.com Link: https://lkml.kernel.org/r/20210910053354.26721-2-wangkefeng.wang@huawei.com Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Marco Elver <elver@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:41 +08:00
BUG_ON(vmap_initialized);
vmalloc: choose a better start address in vm_area_register_early() Percpu embedded first chunk allocator is the firstly option, but it could fail on ARM64, eg, percpu: max_distance=0x5fcfdc640000 too large for vmalloc space 0x781fefff0000 percpu: max_distance=0x600000540000 too large for vmalloc space 0x7dffb7ff0000 percpu: max_distance=0x5fff9adb0000 too large for vmalloc space 0x5dffb7ff0000 then we could get to WARNING: CPU: 15 PID: 461 at vmalloc.c:3087 pcpu_get_vm_areas+0x488/0x838 and the system cannot boot successfully. Let's implement page mapping percpu first chunk allocator as a fallback to the embedding allocator to increase the robustness of the system. Also fix a crash when both NEED_PER_CPU_PAGE_FIRST_CHUNK and KASAN_VMALLOC enabled. Tested on ARM64 qemu with cmdline "percpu_alloc=page". This patch (of 3): There are some fixed locations in the vmalloc area be reserved in ARM(see iotable_init()) and ARM64(see map_kernel()), but for pcpu_page_first_chunk(), it calls vm_area_register_early() and choose VMALLOC_START as the start address of vmap area which could be conflicted with above address, then could trigger a BUG_ON in vm_area_add_early(). Let's choose a suit start address by traversing the vmlist. Link: https://lkml.kernel.org/r/20210910053354.26721-1-wangkefeng.wang@huawei.com Link: https://lkml.kernel.org/r/20210910053354.26721-2-wangkefeng.wang@huawei.com Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Marco Elver <elver@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:41 +08:00
for (p = &vmlist; (cur = *p) != NULL; p = &cur->next) {
if ((unsigned long)cur->addr - addr >= vm->size)
break;
addr = ALIGN((unsigned long)cur->addr + cur->size, align);
}
vmalloc: choose a better start address in vm_area_register_early() Percpu embedded first chunk allocator is the firstly option, but it could fail on ARM64, eg, percpu: max_distance=0x5fcfdc640000 too large for vmalloc space 0x781fefff0000 percpu: max_distance=0x600000540000 too large for vmalloc space 0x7dffb7ff0000 percpu: max_distance=0x5fff9adb0000 too large for vmalloc space 0x5dffb7ff0000 then we could get to WARNING: CPU: 15 PID: 461 at vmalloc.c:3087 pcpu_get_vm_areas+0x488/0x838 and the system cannot boot successfully. Let's implement page mapping percpu first chunk allocator as a fallback to the embedding allocator to increase the robustness of the system. Also fix a crash when both NEED_PER_CPU_PAGE_FIRST_CHUNK and KASAN_VMALLOC enabled. Tested on ARM64 qemu with cmdline "percpu_alloc=page". This patch (of 3): There are some fixed locations in the vmalloc area be reserved in ARM(see iotable_init()) and ARM64(see map_kernel()), but for pcpu_page_first_chunk(), it calls vm_area_register_early() and choose VMALLOC_START as the start address of vmap area which could be conflicted with above address, then could trigger a BUG_ON in vm_area_add_early(). Let's choose a suit start address by traversing the vmlist. Link: https://lkml.kernel.org/r/20210910053354.26721-1-wangkefeng.wang@huawei.com Link: https://lkml.kernel.org/r/20210910053354.26721-2-wangkefeng.wang@huawei.com Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Marco Elver <elver@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:41 +08:00
BUG_ON(addr > VMALLOC_END - vm->size);
vm->addr = (void *)addr;
vm->next = *p;
*p = vm;
kasan: arm64: fix pcpu_page_first_chunk crash with KASAN_VMALLOC With KASAN_VMALLOC and NEED_PER_CPU_PAGE_FIRST_CHUNK the kernel crashes: Unable to handle kernel paging request at virtual address ffff7000028f2000 ... swapper pgtable: 64k pages, 48-bit VAs, pgdp=0000000042440000 [ffff7000028f2000] pgd=000000063e7c0003, p4d=000000063e7c0003, pud=000000063e7c0003, pmd=000000063e7b0003, pte=0000000000000000 Internal error: Oops: 96000007 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 5.13.0-rc4-00003-gc6e6e28f3f30-dirty #62 Hardware name: linux,dummy-virt (DT) pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO BTYPE=--) pc : kasan_check_range+0x90/0x1a0 lr : memcpy+0x88/0xf4 sp : ffff80001378fe20 ... Call trace: kasan_check_range+0x90/0x1a0 pcpu_page_first_chunk+0x3f0/0x568 setup_per_cpu_areas+0xb8/0x184 start_kernel+0x8c/0x328 The vm area used in vm_area_register_early() has no kasan shadow memory, Let's add a new kasan_populate_early_vm_area_shadow() function to populate the vm area shadow memory to fix the issue. [wangkefeng.wang@huawei.com: fix redefinition of 'kasan_populate_early_vm_area_shadow'] Link: https://lkml.kernel.org/r/20211011123211.3936196-1-wangkefeng.wang@huawei.com Link: https://lkml.kernel.org/r/20210910053354.26721-4-wangkefeng.wang@huawei.com Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Marco Elver <elver@google.com> [KASAN] Acked-by: Andrey Konovalov <andreyknvl@gmail.com> [KASAN] Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:47 +08:00
kasan_populate_early_vm_area_shadow(vm->addr, vm->size);
}
static void clear_vm_uninitialized_flag(struct vm_struct *vm)
{
2013-04-30 06:07:35 +08:00
/*
* Before removing VM_UNINITIALIZED,
2013-04-30 06:07:35 +08:00
* we should make sure that vm has proper values.
* Pair with smp_rmb() in show_numa_info().
*/
smp_wmb();
vm->flags &= ~VM_UNINITIALIZED;
}
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
static struct vm_struct *__get_vm_area_node(unsigned long size,
unsigned long align, unsigned long shift, unsigned long flags,
unsigned long start, unsigned long end, int node,
gfp_t gfp_mask, const void *caller)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
{
struct vmap_area *va;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
struct vm_struct *area;
unsigned long requested_size = size;
BUG_ON(in_interrupt());
size = ALIGN(size, 1ul << shift);
if (unlikely(!size))
return NULL;
if (flags & VM_IOREMAP)
align = 1ul << clamp_t(int, get_count_order_long(size),
PAGE_SHIFT, IOREMAP_MAX_ORDER);
area = kzalloc_node(sizeof(*area), gfp_mask & GFP_RECLAIM_MASK, node);
if (unlikely(!area))
return NULL;
mm: vmalloc: add flag preventing guard hole allocation For instrumenting global variables KASan will shadow memory backing memory for modules. So on module loading we will need to allocate memory for shadow and map it at address in shadow that corresponds to the address allocated in module_alloc(). __vmalloc_node_range() could be used for this purpose, except it puts a guard hole after allocated area. Guard hole in shadow memory should be a problem because at some future point we might need to have a shadow memory at address occupied by guard hole. So we could fail to allocate shadow for module_alloc(). Add a new vm_struct flag 'VM_NO_GUARD' indicating that vm area doesn't have a guard hole. Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-02-14 06:40:03 +08:00
if (!(flags & VM_NO_GUARD))
size += PAGE_SIZE;
area->flags = flags;
area->caller = caller;
va = alloc_vmap_area(size, align, start, end, node, gfp_mask, 0, area);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
if (IS_ERR(va)) {
kfree(area);
return NULL;
}
/*
* Mark pages for non-VM_ALLOC mappings as accessible. Do it now as a
* best-effort approach, as they can be mapped outside of vmalloc code.
* For VM_ALLOC mappings, the pages are marked as accessible after
* getting mapped in __vmalloc_node_range().
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
* With hardware tag-based KASAN, marking is skipped for
* non-VM_ALLOC mappings, see __kasan_unpoison_vmalloc().
*/
if (!(flags & VM_ALLOC))
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
area->addr = kasan_unpoison_vmalloc(area->addr, requested_size,
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
KASAN_VMALLOC_PROT_NORMAL);
2022-03-25 09:11:13 +08:00
return area;
}
struct vm_struct *__get_vm_area_caller(unsigned long size, unsigned long flags,
unsigned long start, unsigned long end,
const void *caller)
{
return __get_vm_area_node(size, 1, PAGE_SHIFT, flags, start, end,
NUMA_NO_NODE, GFP_KERNEL, caller);
}
/**
* get_vm_area - reserve a contiguous kernel virtual area
* @size: size of the area
* @flags: %VM_IOREMAP for I/O mappings or VM_ALLOC
*
* Search an area of @size in the kernel virtual mapping area,
* and reserved it for out purposes. Returns the area descriptor
* on success or %NULL on failure.
*
* Return: the area descriptor on success or %NULL on failure.
*/
struct vm_struct *get_vm_area(unsigned long size, unsigned long flags)
{
return __get_vm_area_node(size, 1, PAGE_SHIFT, flags,
VMALLOC_START, VMALLOC_END,
NUMA_NO_NODE, GFP_KERNEL,
__builtin_return_address(0));
vmallocinfo: add caller information Add caller information so that /proc/vmallocinfo shows where the allocation request for a slice of vmalloc memory originated. Results in output like this: 0xffffc20000000000-0xffffc20000801000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20000801000-0xffffc20000806000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000806000-0xffffc20000c07000 4198400 alloc_large_system_hash+0x127/0x246 pages=1024 vmalloc vpages 0xffffc20000c07000-0xffffc20000c0a000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c0a000-0xffffc20000c0c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c0c000-0xffffc20000c0f000 12288 acpi_os_map_memory+0x13/0x1c phys=cff64000 ioremap 0xffffc20000c10000-0xffffc20000c15000 20480 acpi_os_map_memory+0x13/0x1c phys=cff65000 ioremap 0xffffc20000c16000-0xffffc20000c18000 8192 acpi_os_map_memory+0x13/0x1c phys=cff69000 ioremap 0xffffc20000c18000-0xffffc20000c1a000 8192 acpi_os_map_memory+0x13/0x1c phys=fed1f000 ioremap 0xffffc20000c1a000-0xffffc20000c1c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1c000-0xffffc20000c1e000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1e000-0xffffc20000c20000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c20000-0xffffc20000c22000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c22000-0xffffc20000c24000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c24000-0xffffc20000c26000 8192 acpi_os_map_memory+0x13/0x1c phys=e0081000 ioremap 0xffffc20000c26000-0xffffc20000c28000 8192 acpi_os_map_memory+0x13/0x1c phys=e0080000 ioremap 0xffffc20000c28000-0xffffc20000c2d000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000c2d000-0xffffc20000c31000 16384 tcp_init+0xd5/0x31c pages=3 vmalloc 0xffffc20000c31000-0xffffc20000c34000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c34000-0xffffc20000c36000 8192 init_vdso_vars+0xde/0x1f1 0xffffc20000c36000-0xffffc20000c38000 8192 pci_iomap+0x8a/0xb4 phys=d8e00000 ioremap 0xffffc20000c38000-0xffffc20000c3a000 8192 usb_hcd_pci_probe+0x139/0x295 [usbcore] phys=d8e00000 ioremap 0xffffc20000c3a000-0xffffc20000c3e000 16384 sys_swapon+0x509/0xa15 pages=3 vmalloc 0xffffc20000c40000-0xffffc20000c61000 135168 e1000_probe+0x1c4/0xa32 phys=d8a20000 ioremap 0xffffc20000c61000-0xffffc20000c6a000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c6a000-0xffffc20000c73000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c73000-0xffffc20000c7c000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c7c000-0xffffc20000c7f000 12288 e1000e_setup_tx_resources+0x29/0xbe pages=2 vmalloc 0xffffc20000c80000-0xffffc20001481000 8392704 pci_mmcfg_arch_init+0x90/0x118 phys=e0000000 ioremap 0xffffc20001481000-0xffffc20001682000 2101248 alloc_large_system_hash+0x127/0x246 pages=512 vmalloc 0xffffc20001682000-0xffffc20001e83000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20001e83000-0xffffc20002204000 3674112 alloc_large_system_hash+0x127/0x246 pages=896 vmalloc vpages 0xffffc20002204000-0xffffc2000220d000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000220d000-0xffffc20002216000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002216000-0xffffc2000221f000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000221f000-0xffffc20002228000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002228000-0xffffc20002231000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002231000-0xffffc20002234000 12288 e1000e_setup_rx_resources+0x35/0x122 pages=2 vmalloc 0xffffc20002240000-0xffffc20002261000 135168 e1000_probe+0x1c4/0xa32 phys=d8a60000 ioremap 0xffffc20002261000-0xffffc2000270c000 4894720 sys_swapon+0x509/0xa15 pages=1194 vmalloc vpages 0xffffffffa0000000-0xffffffffa0022000 139264 module_alloc+0x4f/0x55 pages=33 vmalloc 0xffffffffa0022000-0xffffffffa0029000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc 0xffffffffa002b000-0xffffffffa0034000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa0034000-0xffffffffa003d000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa003d000-0xffffffffa0049000 49152 module_alloc+0x4f/0x55 pages=11 vmalloc 0xffffffffa0049000-0xffffffffa0050000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Lameter <clameter@sgi.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:12:42 +08:00
}
struct vm_struct *get_vm_area_caller(unsigned long size, unsigned long flags,
const void *caller)
vmallocinfo: add caller information Add caller information so that /proc/vmallocinfo shows where the allocation request for a slice of vmalloc memory originated. Results in output like this: 0xffffc20000000000-0xffffc20000801000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20000801000-0xffffc20000806000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000806000-0xffffc20000c07000 4198400 alloc_large_system_hash+0x127/0x246 pages=1024 vmalloc vpages 0xffffc20000c07000-0xffffc20000c0a000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c0a000-0xffffc20000c0c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c0c000-0xffffc20000c0f000 12288 acpi_os_map_memory+0x13/0x1c phys=cff64000 ioremap 0xffffc20000c10000-0xffffc20000c15000 20480 acpi_os_map_memory+0x13/0x1c phys=cff65000 ioremap 0xffffc20000c16000-0xffffc20000c18000 8192 acpi_os_map_memory+0x13/0x1c phys=cff69000 ioremap 0xffffc20000c18000-0xffffc20000c1a000 8192 acpi_os_map_memory+0x13/0x1c phys=fed1f000 ioremap 0xffffc20000c1a000-0xffffc20000c1c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1c000-0xffffc20000c1e000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1e000-0xffffc20000c20000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c20000-0xffffc20000c22000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c22000-0xffffc20000c24000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c24000-0xffffc20000c26000 8192 acpi_os_map_memory+0x13/0x1c phys=e0081000 ioremap 0xffffc20000c26000-0xffffc20000c28000 8192 acpi_os_map_memory+0x13/0x1c phys=e0080000 ioremap 0xffffc20000c28000-0xffffc20000c2d000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000c2d000-0xffffc20000c31000 16384 tcp_init+0xd5/0x31c pages=3 vmalloc 0xffffc20000c31000-0xffffc20000c34000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c34000-0xffffc20000c36000 8192 init_vdso_vars+0xde/0x1f1 0xffffc20000c36000-0xffffc20000c38000 8192 pci_iomap+0x8a/0xb4 phys=d8e00000 ioremap 0xffffc20000c38000-0xffffc20000c3a000 8192 usb_hcd_pci_probe+0x139/0x295 [usbcore] phys=d8e00000 ioremap 0xffffc20000c3a000-0xffffc20000c3e000 16384 sys_swapon+0x509/0xa15 pages=3 vmalloc 0xffffc20000c40000-0xffffc20000c61000 135168 e1000_probe+0x1c4/0xa32 phys=d8a20000 ioremap 0xffffc20000c61000-0xffffc20000c6a000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c6a000-0xffffc20000c73000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c73000-0xffffc20000c7c000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c7c000-0xffffc20000c7f000 12288 e1000e_setup_tx_resources+0x29/0xbe pages=2 vmalloc 0xffffc20000c80000-0xffffc20001481000 8392704 pci_mmcfg_arch_init+0x90/0x118 phys=e0000000 ioremap 0xffffc20001481000-0xffffc20001682000 2101248 alloc_large_system_hash+0x127/0x246 pages=512 vmalloc 0xffffc20001682000-0xffffc20001e83000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20001e83000-0xffffc20002204000 3674112 alloc_large_system_hash+0x127/0x246 pages=896 vmalloc vpages 0xffffc20002204000-0xffffc2000220d000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000220d000-0xffffc20002216000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002216000-0xffffc2000221f000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000221f000-0xffffc20002228000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002228000-0xffffc20002231000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002231000-0xffffc20002234000 12288 e1000e_setup_rx_resources+0x35/0x122 pages=2 vmalloc 0xffffc20002240000-0xffffc20002261000 135168 e1000_probe+0x1c4/0xa32 phys=d8a60000 ioremap 0xffffc20002261000-0xffffc2000270c000 4894720 sys_swapon+0x509/0xa15 pages=1194 vmalloc vpages 0xffffffffa0000000-0xffffffffa0022000 139264 module_alloc+0x4f/0x55 pages=33 vmalloc 0xffffffffa0022000-0xffffffffa0029000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc 0xffffffffa002b000-0xffffffffa0034000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa0034000-0xffffffffa003d000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa003d000-0xffffffffa0049000 49152 module_alloc+0x4f/0x55 pages=11 vmalloc 0xffffffffa0049000-0xffffffffa0050000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Lameter <clameter@sgi.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:12:42 +08:00
{
return __get_vm_area_node(size, 1, PAGE_SHIFT, flags,
VMALLOC_START, VMALLOC_END,
NUMA_NO_NODE, GFP_KERNEL, caller);
}
/**
* find_vm_area - find a continuous kernel virtual area
* @addr: base address
*
* Search for the kernel VM area starting at @addr, and return it.
* It is up to the caller to do all required locking to keep the returned
* pointer valid.
*
* Return: the area descriptor on success or %NULL on failure.
*/
struct vm_struct *find_vm_area(const void *addr)
{
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
struct vmap_area *va;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
va = find_vmap_area((unsigned long)addr);
if (!va)
return NULL;
return va->vm;
}
/**
* remove_vm_area - find and remove a continuous kernel virtual area
* @addr: base address
*
* Search for the kernel VM area starting at @addr, and remove it.
* This function returns the found VM area, but using it is NOT safe
* on SMP machines, except for its size or flags.
*
* Return: the area descriptor on success or %NULL on failure.
*/
struct vm_struct *remove_vm_area(const void *addr)
{
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
struct vmap_area *va;
struct vm_struct *vm;
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
might_sleep();
if (WARN(!PAGE_ALIGNED(addr), "Trying to vfree() bad address (%p)\n",
addr))
return NULL;
va = find_unlink_vmap_area((unsigned long)addr);
if (!va || !va->vm)
return NULL;
vm = va->vm;
debug_check_no_locks_freed(vm->addr, get_vm_area_size(vm));
debug_check_no_obj_freed(vm->addr, get_vm_area_size(vm));
kasan_free_module_shadow(vm);
kasan_poison_vmalloc(vm->addr, get_vm_area_size(vm));
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
free_unmap_vmap_area(va);
return vm;
}
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
static inline void set_area_direct_map(const struct vm_struct *area,
int (*set_direct_map)(struct page *page))
{
int i;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
/* HUGE_VMALLOC passes small pages to set_direct_map */
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
for (i = 0; i < area->nr_pages; i++)
if (page_address(area->pages[i]))
set_direct_map(area->pages[i]);
}
/*
* Flush the vm mapping and reset the direct map.
*/
static void vm_reset_perms(struct vm_struct *area)
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
{
unsigned long start = ULONG_MAX, end = 0;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
unsigned int page_order = vm_area_page_order(area);
mm/vmalloc: Avoid rare case of flushing TLB with weird arguments In a rare case, flush_tlb_kernel_range() could be called with a start higher than the end. In vm_remove_mappings(), in case page_address() returns 0 for all pages (for example they were all in highmem), _vm_unmap_aliases() will be called with start = ULONG_MAX, end = 0 and flush = 1. If at the same time, the vmalloc purge operation is triggered by something else while the current operation is between remove_vm_area() and _vm_unmap_aliases(), then the vm mapping just removed will be already purged. In this case the call of vm_unmap_aliases() may not find any other mappings to flush and so end up flushing start = ULONG_MAX, end = 0. So only set flush = true if we find something in the direct mapping that we need to flush, and this way this can't happen. Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Meelis Roos <mroos@linux.ee> Cc: Nadav Amit <namit@vmware.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 868b104d7379 ("mm/vmalloc: Add flag for freeing of special permsissions") Link: https://lkml.kernel.org/r/20190527211058.2729-3-rick.p.edgecombe@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-05-28 05:10:58 +08:00
int flush_dmap = 0;
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
int i;
/*
* Find the start and end range of the direct mappings to make sure that
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
* the vm_unmap_aliases() flush includes the direct map.
*/
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
for (i = 0; i < area->nr_pages; i += 1U << page_order) {
unsigned long addr = (unsigned long)page_address(area->pages[i]);
if (addr) {
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
unsigned long page_size;
page_size = PAGE_SIZE << page_order;
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
start = min(addr, start);
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
end = max(addr + page_size, end);
mm/vmalloc: Avoid rare case of flushing TLB with weird arguments In a rare case, flush_tlb_kernel_range() could be called with a start higher than the end. In vm_remove_mappings(), in case page_address() returns 0 for all pages (for example they were all in highmem), _vm_unmap_aliases() will be called with start = ULONG_MAX, end = 0 and flush = 1. If at the same time, the vmalloc purge operation is triggered by something else while the current operation is between remove_vm_area() and _vm_unmap_aliases(), then the vm mapping just removed will be already purged. In this case the call of vm_unmap_aliases() may not find any other mappings to flush and so end up flushing start = ULONG_MAX, end = 0. So only set flush = true if we find something in the direct mapping that we need to flush, and this way this can't happen. Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Meelis Roos <mroos@linux.ee> Cc: Nadav Amit <namit@vmware.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 868b104d7379 ("mm/vmalloc: Add flag for freeing of special permsissions") Link: https://lkml.kernel.org/r/20190527211058.2729-3-rick.p.edgecombe@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-05-28 05:10:58 +08:00
flush_dmap = 1;
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
}
}
/*
* Set direct map to something invalid so that it won't be cached if
* there are any accesses after the TLB flush, then flush the TLB and
* reset the direct map permissions to the default.
*/
set_area_direct_map(area, set_direct_map_invalid_noflush);
mm/vmalloc: Avoid rare case of flushing TLB with weird arguments In a rare case, flush_tlb_kernel_range() could be called with a start higher than the end. In vm_remove_mappings(), in case page_address() returns 0 for all pages (for example they were all in highmem), _vm_unmap_aliases() will be called with start = ULONG_MAX, end = 0 and flush = 1. If at the same time, the vmalloc purge operation is triggered by something else while the current operation is between remove_vm_area() and _vm_unmap_aliases(), then the vm mapping just removed will be already purged. In this case the call of vm_unmap_aliases() may not find any other mappings to flush and so end up flushing start = ULONG_MAX, end = 0. So only set flush = true if we find something in the direct mapping that we need to flush, and this way this can't happen. Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Meelis Roos <mroos@linux.ee> Cc: Nadav Amit <namit@vmware.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 868b104d7379 ("mm/vmalloc: Add flag for freeing of special permsissions") Link: https://lkml.kernel.org/r/20190527211058.2729-3-rick.p.edgecombe@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-05-28 05:10:58 +08:00
_vm_unmap_aliases(start, end, flush_dmap);
mm/vmalloc: Add flag for freeing of special permsissions Add a new flag VM_FLUSH_RESET_PERMS, for enabling vfree operations to immediately clear executable TLB entries before freeing pages, and handle resetting permissions on the directmap. This flag is useful for any kind of memory with elevated permissions, or where there can be related permissions changes on the directmap. Today this is RO+X and RO memory. Although this enables directly vfreeing non-writeable memory now, non-writable memory cannot be freed in an interrupt because the allocation itself is used as a node on deferred free list. So when RO memory needs to be freed in an interrupt the code doing the vfree needs to have its own work queue, as was the case before the deferred vfree list was added to vmalloc. For architectures with set_direct_map_ implementations this whole operation can be done with one TLB flush when centralized like this. For others with directmap permissions, currently only arm64, a backup method using set_memory functions is used to reset the directmap. When arm64 adds set_direct_map_ functions, this backup can be removed. When the TLB is flushed to both remove TLB entries for the vmalloc range mapping and the direct map permissions, the lazy purge operation could be done to try to save a TLB flush later. However today vm_unmap_aliases could flush a TLB range that does not include the directmap. So a helper is added with extra parameters that can allow both the vmalloc address and the direct mapping to be flushed during this operation. The behavior of the normal vm_unmap_aliases function is unchanged. Suggested-by: Dave Hansen <dave.hansen@intel.com> Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <akpm@linux-foundation.org> Cc: <ard.biesheuvel@linaro.org> Cc: <deneen.t.dock@intel.com> Cc: <kernel-hardening@lists.openwall.com> Cc: <kristen@linux.intel.com> Cc: <linux_dti@icloud.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190426001143.4983-17-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-04-26 08:11:36 +08:00
set_area_direct_map(area, set_direct_map_default_noflush);
}
static void delayed_vfree_work(struct work_struct *w)
{
struct vfree_deferred *p = container_of(w, struct vfree_deferred, wq);
struct llist_node *t, *llnode;
llist_for_each_safe(llnode, t, llist_del_all(&p->list))
vfree(llnode);
}
/**
* vfree_atomic - release memory allocated by vmalloc()
* @addr: memory base address
*
* This one is just like vfree() but can be called in any atomic context
* except NMIs.
*/
void vfree_atomic(const void *addr)
{
struct vfree_deferred *p = raw_cpu_ptr(&vfree_deferred);
BUG_ON(in_nmi());
kmemleak_free(addr);
/*
* Use raw_cpu_ptr() because this can be called from preemptible
* context. Preemption is absolutely fine here, because the llist_add()
* implementation is lockless, so it works even if we are adding to
* another cpu's list. schedule_work() should be fine with this too.
*/
if (addr && llist_add((struct llist_node *)addr, &p->list))
schedule_work(&p->wq);
}
/**
mm: update the documentation for vfree Patch series "remove alloc_vm_area", v4. This series removes alloc_vm_area, which was left over from the big vmalloc interface rework. It is a rather arkane interface, basicaly the equivalent of get_vm_area + actually faulting in all PTEs in the allocated area. It was originally addeds for Xen (which isn't modular to start with), and then grew users in zsmalloc and i915 which seems to mostly qualify as abuses of the interface, especially for i915 as a random driver should not set up PTE bits directly. This patch (of 11): * Document that you can call vfree() on an address returned from vmap() * Remove the note about the minimum size -- the minimum size of a vmalloc allocation is one page * Add a Context: section * Fix capitalisation * Reword the prohibition on calling from NMI context to avoid a double negative Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: Stefano Stabellini <sstabellini@kernel.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Link: https://lkml.kernel.org/r/20201002122204.1534411-1-hch@lst.de Link: https://lkml.kernel.org/r/20201002122204.1534411-2-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-18 07:15:03 +08:00
* vfree - Release memory allocated by vmalloc()
* @addr: Memory base address
*
mm: update the documentation for vfree Patch series "remove alloc_vm_area", v4. This series removes alloc_vm_area, which was left over from the big vmalloc interface rework. It is a rather arkane interface, basicaly the equivalent of get_vm_area + actually faulting in all PTEs in the allocated area. It was originally addeds for Xen (which isn't modular to start with), and then grew users in zsmalloc and i915 which seems to mostly qualify as abuses of the interface, especially for i915 as a random driver should not set up PTE bits directly. This patch (of 11): * Document that you can call vfree() on an address returned from vmap() * Remove the note about the minimum size -- the minimum size of a vmalloc allocation is one page * Add a Context: section * Fix capitalisation * Reword the prohibition on calling from NMI context to avoid a double negative Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: Stefano Stabellini <sstabellini@kernel.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Link: https://lkml.kernel.org/r/20201002122204.1534411-1-hch@lst.de Link: https://lkml.kernel.org/r/20201002122204.1534411-2-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-18 07:15:03 +08:00
* Free the virtually continuous memory area starting at @addr, as obtained
* from one of the vmalloc() family of APIs. This will usually also free the
* physical memory underlying the virtual allocation, but that memory is
* reference counted, so it will not be freed until the last user goes away.
*
mm: update the documentation for vfree Patch series "remove alloc_vm_area", v4. This series removes alloc_vm_area, which was left over from the big vmalloc interface rework. It is a rather arkane interface, basicaly the equivalent of get_vm_area + actually faulting in all PTEs in the allocated area. It was originally addeds for Xen (which isn't modular to start with), and then grew users in zsmalloc and i915 which seems to mostly qualify as abuses of the interface, especially for i915 as a random driver should not set up PTE bits directly. This patch (of 11): * Document that you can call vfree() on an address returned from vmap() * Remove the note about the minimum size -- the minimum size of a vmalloc allocation is one page * Add a Context: section * Fix capitalisation * Reword the prohibition on calling from NMI context to avoid a double negative Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: Stefano Stabellini <sstabellini@kernel.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Link: https://lkml.kernel.org/r/20201002122204.1534411-1-hch@lst.de Link: https://lkml.kernel.org/r/20201002122204.1534411-2-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-18 07:15:03 +08:00
* If @addr is NULL, no operation is performed.
*
mm: update the documentation for vfree Patch series "remove alloc_vm_area", v4. This series removes alloc_vm_area, which was left over from the big vmalloc interface rework. It is a rather arkane interface, basicaly the equivalent of get_vm_area + actually faulting in all PTEs in the allocated area. It was originally addeds for Xen (which isn't modular to start with), and then grew users in zsmalloc and i915 which seems to mostly qualify as abuses of the interface, especially for i915 as a random driver should not set up PTE bits directly. This patch (of 11): * Document that you can call vfree() on an address returned from vmap() * Remove the note about the minimum size -- the minimum size of a vmalloc allocation is one page * Add a Context: section * Fix capitalisation * Reword the prohibition on calling from NMI context to avoid a double negative Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: Stefano Stabellini <sstabellini@kernel.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Link: https://lkml.kernel.org/r/20201002122204.1534411-1-hch@lst.de Link: https://lkml.kernel.org/r/20201002122204.1534411-2-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-18 07:15:03 +08:00
* Context:
* May sleep if called *not* from interrupt context.
mm: update the documentation for vfree Patch series "remove alloc_vm_area", v4. This series removes alloc_vm_area, which was left over from the big vmalloc interface rework. It is a rather arkane interface, basicaly the equivalent of get_vm_area + actually faulting in all PTEs in the allocated area. It was originally addeds for Xen (which isn't modular to start with), and then grew users in zsmalloc and i915 which seems to mostly qualify as abuses of the interface, especially for i915 as a random driver should not set up PTE bits directly. This patch (of 11): * Document that you can call vfree() on an address returned from vmap() * Remove the note about the minimum size -- the minimum size of a vmalloc allocation is one page * Add a Context: section * Fix capitalisation * Reword the prohibition on calling from NMI context to avoid a double negative Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: Stefano Stabellini <sstabellini@kernel.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Link: https://lkml.kernel.org/r/20201002122204.1534411-1-hch@lst.de Link: https://lkml.kernel.org/r/20201002122204.1534411-2-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-18 07:15:03 +08:00
* Must not be called in NMI context (strictly speaking, it could be
* if we have CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG, but making the calling
* conventions for vfree() arch-dependent would be a really bad idea).
*/
void vfree(const void *addr)
{
struct vm_struct *vm;
int i;
if (unlikely(in_interrupt())) {
vfree_atomic(addr);
return;
}
BUG_ON(in_nmi());
kmemleak_free(addr);
might_sleep();
if (!addr)
return;
vm = remove_vm_area(addr);
if (unlikely(!vm)) {
WARN(1, KERN_ERR "Trying to vfree() nonexistent vm area (%p)\n",
addr);
return;
}
if (unlikely(vm->flags & VM_FLUSH_RESET_PERMS))
vm_reset_perms(vm);
for (i = 0; i < vm->nr_pages; i++) {
struct page *page = vm->pages[i];
BUG_ON(!page);
mod_memcg_page_state(page, MEMCG_VMALLOC, -1);
/*
* High-order allocs for huge vmallocs are split, so
* can be freed as an array of order-0 allocations
*/
__free_page(page);
cond_resched();
}
atomic_long_sub(vm->nr_pages, &nr_vmalloc_pages);
kvfree(vm->pages);
kfree(vm);
}
EXPORT_SYMBOL(vfree);
/**
* vunmap - release virtual mapping obtained by vmap()
* @addr: memory base address
*
* Free the virtually contiguous memory area starting at @addr,
* which was created from the page array passed to vmap().
*
* Must not be called in interrupt context.
*/
void vunmap(const void *addr)
{
struct vm_struct *vm;
BUG_ON(in_interrupt());
might_sleep();
if (!addr)
return;
vm = remove_vm_area(addr);
if (unlikely(!vm)) {
WARN(1, KERN_ERR "Trying to vunmap() nonexistent vm area (%p)\n",
addr);
return;
}
kfree(vm);
}
EXPORT_SYMBOL(vunmap);
/**
* vmap - map an array of pages into virtually contiguous space
* @pages: array of page pointers
* @count: number of pages to map
* @flags: vm_area->flags
* @prot: page protection for the mapping
*
* Maps @count pages from @pages into contiguous kernel virtual space.
* If @flags contains %VM_MAP_PUT_PAGES the ownership of the pages array itself
* (which must be kmalloc or vmalloc memory) and one reference per pages in it
* are transferred from the caller to vmap(), and will be freed / dropped when
* vfree() is called on the return value.
*
* Return: the address of the area or %NULL on failure
*/
void *vmap(struct page **pages, unsigned int count,
unsigned long flags, pgprot_t prot)
{
struct vm_struct *area;
unsigned long addr;
unsigned long size; /* In bytes */
might_sleep();
if (WARN_ON_ONCE(flags & VM_FLUSH_RESET_PERMS))
return NULL;
/*
* Your top guard is someone else's bottom guard. Not having a top
* guard compromises someone else's mappings too.
*/
if (WARN_ON_ONCE(flags & VM_NO_GUARD))
flags &= ~VM_NO_GUARD;
if (count > totalram_pages())
return NULL;
size = (unsigned long)count << PAGE_SHIFT;
area = get_vm_area_caller(size, flags, __builtin_return_address(0));
if (!area)
return NULL;
vmallocinfo: add caller information Add caller information so that /proc/vmallocinfo shows where the allocation request for a slice of vmalloc memory originated. Results in output like this: 0xffffc20000000000-0xffffc20000801000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20000801000-0xffffc20000806000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000806000-0xffffc20000c07000 4198400 alloc_large_system_hash+0x127/0x246 pages=1024 vmalloc vpages 0xffffc20000c07000-0xffffc20000c0a000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c0a000-0xffffc20000c0c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c0c000-0xffffc20000c0f000 12288 acpi_os_map_memory+0x13/0x1c phys=cff64000 ioremap 0xffffc20000c10000-0xffffc20000c15000 20480 acpi_os_map_memory+0x13/0x1c phys=cff65000 ioremap 0xffffc20000c16000-0xffffc20000c18000 8192 acpi_os_map_memory+0x13/0x1c phys=cff69000 ioremap 0xffffc20000c18000-0xffffc20000c1a000 8192 acpi_os_map_memory+0x13/0x1c phys=fed1f000 ioremap 0xffffc20000c1a000-0xffffc20000c1c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1c000-0xffffc20000c1e000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1e000-0xffffc20000c20000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c20000-0xffffc20000c22000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c22000-0xffffc20000c24000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c24000-0xffffc20000c26000 8192 acpi_os_map_memory+0x13/0x1c phys=e0081000 ioremap 0xffffc20000c26000-0xffffc20000c28000 8192 acpi_os_map_memory+0x13/0x1c phys=e0080000 ioremap 0xffffc20000c28000-0xffffc20000c2d000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000c2d000-0xffffc20000c31000 16384 tcp_init+0xd5/0x31c pages=3 vmalloc 0xffffc20000c31000-0xffffc20000c34000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c34000-0xffffc20000c36000 8192 init_vdso_vars+0xde/0x1f1 0xffffc20000c36000-0xffffc20000c38000 8192 pci_iomap+0x8a/0xb4 phys=d8e00000 ioremap 0xffffc20000c38000-0xffffc20000c3a000 8192 usb_hcd_pci_probe+0x139/0x295 [usbcore] phys=d8e00000 ioremap 0xffffc20000c3a000-0xffffc20000c3e000 16384 sys_swapon+0x509/0xa15 pages=3 vmalloc 0xffffc20000c40000-0xffffc20000c61000 135168 e1000_probe+0x1c4/0xa32 phys=d8a20000 ioremap 0xffffc20000c61000-0xffffc20000c6a000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c6a000-0xffffc20000c73000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c73000-0xffffc20000c7c000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c7c000-0xffffc20000c7f000 12288 e1000e_setup_tx_resources+0x29/0xbe pages=2 vmalloc 0xffffc20000c80000-0xffffc20001481000 8392704 pci_mmcfg_arch_init+0x90/0x118 phys=e0000000 ioremap 0xffffc20001481000-0xffffc20001682000 2101248 alloc_large_system_hash+0x127/0x246 pages=512 vmalloc 0xffffc20001682000-0xffffc20001e83000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20001e83000-0xffffc20002204000 3674112 alloc_large_system_hash+0x127/0x246 pages=896 vmalloc vpages 0xffffc20002204000-0xffffc2000220d000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000220d000-0xffffc20002216000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002216000-0xffffc2000221f000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000221f000-0xffffc20002228000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002228000-0xffffc20002231000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002231000-0xffffc20002234000 12288 e1000e_setup_rx_resources+0x35/0x122 pages=2 vmalloc 0xffffc20002240000-0xffffc20002261000 135168 e1000_probe+0x1c4/0xa32 phys=d8a60000 ioremap 0xffffc20002261000-0xffffc2000270c000 4894720 sys_swapon+0x509/0xa15 pages=1194 vmalloc vpages 0xffffffffa0000000-0xffffffffa0022000 139264 module_alloc+0x4f/0x55 pages=33 vmalloc 0xffffffffa0022000-0xffffffffa0029000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc 0xffffffffa002b000-0xffffffffa0034000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa0034000-0xffffffffa003d000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa003d000-0xffffffffa0049000 49152 module_alloc+0x4f/0x55 pages=11 vmalloc 0xffffffffa0049000-0xffffffffa0050000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Lameter <clameter@sgi.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:12:42 +08:00
addr = (unsigned long)area->addr;
if (vmap_pages_range(addr, addr + size, pgprot_nx(prot),
pages, PAGE_SHIFT) < 0) {
vunmap(area->addr);
return NULL;
}
if (flags & VM_MAP_PUT_PAGES) {
area->pages = pages;
area->nr_pages = count;
}
return area->addr;
}
EXPORT_SYMBOL(vmap);
#ifdef CONFIG_VMAP_PFN
struct vmap_pfn_data {
unsigned long *pfns;
pgprot_t prot;
unsigned int idx;
};
static int vmap_pfn_apply(pte_t *pte, unsigned long addr, void *private)
{
struct vmap_pfn_data *data = private;
unsigned long pfn = data->pfns[data->idx];
pte_t ptent;
if (WARN_ON_ONCE(pfn_valid(pfn)))
return -EINVAL;
ptent = pte_mkspecial(pfn_pte(pfn, data->prot));
set_pte_at(&init_mm, addr, pte, ptent);
data->idx++;
return 0;
}
/**
* vmap_pfn - map an array of PFNs into virtually contiguous space
* @pfns: array of PFNs
* @count: number of pages to map
* @prot: page protection for the mapping
*
* Maps @count PFNs from @pfns into contiguous kernel virtual space and returns
* the start address of the mapping.
*/
void *vmap_pfn(unsigned long *pfns, unsigned int count, pgprot_t prot)
{
struct vmap_pfn_data data = { .pfns = pfns, .prot = pgprot_nx(prot) };
struct vm_struct *area;
area = get_vm_area_caller(count * PAGE_SIZE, VM_IOREMAP,
__builtin_return_address(0));
if (!area)
return NULL;
if (apply_to_page_range(&init_mm, (unsigned long)area->addr,
count * PAGE_SIZE, vmap_pfn_apply, &data)) {
free_vm_area(area);
return NULL;
}
2023-08-10 00:46:33 +08:00
flush_cache_vmap((unsigned long)area->addr,
(unsigned long)area->addr + count * PAGE_SIZE);
return area->addr;
}
EXPORT_SYMBOL_GPL(vmap_pfn);
#endif /* CONFIG_VMAP_PFN */
static inline unsigned int
vm_area_alloc_pages(gfp_t gfp, int nid,
unsigned int order, unsigned int nr_pages, struct page **pages)
{
unsigned int nr_allocated = 0;
mm, vmalloc: fix high order __GFP_NOFAIL allocations Gao Xiang has reported that the page allocator complains about high order __GFP_NOFAIL request coming from the vmalloc core: __alloc_pages+0x1cb/0x5b0 mm/page_alloc.c:5549 alloc_pages+0x1aa/0x270 mm/mempolicy.c:2286 vm_area_alloc_pages mm/vmalloc.c:2989 [inline] __vmalloc_area_node mm/vmalloc.c:3057 [inline] __vmalloc_node_range+0x978/0x13c0 mm/vmalloc.c:3227 kvmalloc_node+0x156/0x1a0 mm/util.c:606 kvmalloc include/linux/slab.h:737 [inline] kvmalloc_array include/linux/slab.h:755 [inline] kvcalloc include/linux/slab.h:760 [inline] it seems that I have completely missed high order allocation backing vmalloc areas case when implementing __GFP_NOFAIL support. This means that [k]vmalloc at al. can allocate higher order allocations with __GFP_NOFAIL which can trigger OOM killer for non-costly orders easily or cause a lot of reclaim/compaction activity if those requests cannot be satisfied. Fix the issue by falling back to zero order allocations for __GFP_NOFAIL requests if the high order request fails. Link: https://lkml.kernel.org/r/ZAXynvdNqcI0f6Us@dhcp22.suse.cz Fixes: 9376130c390a ("mm/vmalloc: add support for __GFP_NOFAIL") Reported-by: Gao Xiang <hsiangkao@linux.alibaba.com> Link: https://lkml.kernel.org/r/20230305053035.1911-1-hsiangkao@linux.alibaba.com Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-06 16:15:17 +08:00
gfp_t alloc_gfp = gfp;
bool nofail = false;
mm/vmalloc: fix numa spreading for large hash tables Eric Dumazet reported a strange numa spreading info in [1], and found commit 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings") introduced this issue [2]. Dig into the difference before and after this patch, page allocation has some difference: before: alloc_large_system_hash __vmalloc __vmalloc_node(..., NUMA_NO_NODE, ...) __vmalloc_node_range __vmalloc_area_node alloc_page /* because NUMA_NO_NODE, so choose alloc_page branch */ alloc_pages_current alloc_page_interleave /* can be proved by print policy mode */ after: alloc_large_system_hash __vmalloc __vmalloc_node(..., NUMA_NO_NODE, ...) __vmalloc_node_range __vmalloc_area_node alloc_pages_node /* choose nid by nuam_mem_id() */ __alloc_pages_node(nid, ....) So after commit 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings"), it will allocate memory in current node instead of interleaving allocate memory. Link: https://lore.kernel.org/linux-mm/CANn89iL6AAyWhfxdHO+jaT075iOa3XcYn9k6JJc7JR2XYn6k_Q@mail.gmail.com/ [1] Link: https://lore.kernel.org/linux-mm/CANn89iLofTR=AK-QOZY87RdUZENCZUT4O6a0hvhu3_EwRMerOg@mail.gmail.com/ [2] Link: https://lkml.kernel.org/r/20211021080744.874701-2-chenwandun@huawei.com Fixes: 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reported-by: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Uladzislau Rezki <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-10-29 05:36:24 +08:00
struct page *page;
int i;
/*
* For order-0 pages we make use of bulk allocator, if
* the page array is partly or not at all populated due
* to fails, fallback to a single page allocator that is
* more permissive.
*/
mm/vmalloc: introduce alloc_pages_bulk_array_mempolicy to accelerate memory allocation Commit ffb29b1c255a ("mm/vmalloc: fix numa spreading for large hash tables") can cause significant performance regressions in some situations as Andrew mentioned in [1]. The main situation is vmalloc, vmalloc will allocate pages with NUMA_NO_NODE by default, that will result in alloc page one by one; In order to solve this, __alloc_pages_bulk and mempolicy should be considered at the same time. 1) If node is specified in memory allocation request, it will alloc all pages by __alloc_pages_bulk. 2) If interleaving allocate memory, it will cauculate how many pages should be allocated in each node, and use __alloc_pages_bulk to alloc pages in each node. [1]: https://lore.kernel.org/lkml/CALvZod4G3SzP3kWxQYn0fj+VgG-G3yWXz=gz17+3N57ru1iajw@mail.gmail.com/t/#m750c8e3231206134293b089feaa090590afa0f60 [akpm@linux-foundation.org: coding style fixes] [akpm@linux-foundation.org: make two functions static] [akpm@linux-foundation.org: fix CONFIG_NUMA=n build] Link: https://lkml.kernel.org/r/20211021080744.874701-3-chenwandun@huawei.com Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:53 +08:00
if (!order) {
mm, vmalloc: fix high order __GFP_NOFAIL allocations Gao Xiang has reported that the page allocator complains about high order __GFP_NOFAIL request coming from the vmalloc core: __alloc_pages+0x1cb/0x5b0 mm/page_alloc.c:5549 alloc_pages+0x1aa/0x270 mm/mempolicy.c:2286 vm_area_alloc_pages mm/vmalloc.c:2989 [inline] __vmalloc_area_node mm/vmalloc.c:3057 [inline] __vmalloc_node_range+0x978/0x13c0 mm/vmalloc.c:3227 kvmalloc_node+0x156/0x1a0 mm/util.c:606 kvmalloc include/linux/slab.h:737 [inline] kvmalloc_array include/linux/slab.h:755 [inline] kvcalloc include/linux/slab.h:760 [inline] it seems that I have completely missed high order allocation backing vmalloc areas case when implementing __GFP_NOFAIL support. This means that [k]vmalloc at al. can allocate higher order allocations with __GFP_NOFAIL which can trigger OOM killer for non-costly orders easily or cause a lot of reclaim/compaction activity if those requests cannot be satisfied. Fix the issue by falling back to zero order allocations for __GFP_NOFAIL requests if the high order request fails. Link: https://lkml.kernel.org/r/ZAXynvdNqcI0f6Us@dhcp22.suse.cz Fixes: 9376130c390a ("mm/vmalloc: add support for __GFP_NOFAIL") Reported-by: Gao Xiang <hsiangkao@linux.alibaba.com> Link: https://lkml.kernel.org/r/20230305053035.1911-1-hsiangkao@linux.alibaba.com Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-06 16:15:17 +08:00
/* bulk allocator doesn't support nofail req. officially */
gfp_t bulk_gfp = gfp & ~__GFP_NOFAIL;
while (nr_allocated < nr_pages) {
unsigned int nr, nr_pages_request;
/*
* A maximum allowed request is hard-coded and is 100
* pages per call. That is done in order to prevent a
* long preemption off scenario in the bulk-allocator
* so the range is [1:100].
*/
nr_pages_request = min(100U, nr_pages - nr_allocated);
mm/vmalloc: introduce alloc_pages_bulk_array_mempolicy to accelerate memory allocation Commit ffb29b1c255a ("mm/vmalloc: fix numa spreading for large hash tables") can cause significant performance regressions in some situations as Andrew mentioned in [1]. The main situation is vmalloc, vmalloc will allocate pages with NUMA_NO_NODE by default, that will result in alloc page one by one; In order to solve this, __alloc_pages_bulk and mempolicy should be considered at the same time. 1) If node is specified in memory allocation request, it will alloc all pages by __alloc_pages_bulk. 2) If interleaving allocate memory, it will cauculate how many pages should be allocated in each node, and use __alloc_pages_bulk to alloc pages in each node. [1]: https://lore.kernel.org/lkml/CALvZod4G3SzP3kWxQYn0fj+VgG-G3yWXz=gz17+3N57ru1iajw@mail.gmail.com/t/#m750c8e3231206134293b089feaa090590afa0f60 [akpm@linux-foundation.org: coding style fixes] [akpm@linux-foundation.org: make two functions static] [akpm@linux-foundation.org: fix CONFIG_NUMA=n build] Link: https://lkml.kernel.org/r/20211021080744.874701-3-chenwandun@huawei.com Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:53 +08:00
/* memory allocation should consider mempolicy, we can't
* wrongly use nearest node when nid == NUMA_NO_NODE,
* otherwise memory may be allocated in only one node,
* but mempolicy wants to alloc memory by interleaving.
mm/vmalloc: introduce alloc_pages_bulk_array_mempolicy to accelerate memory allocation Commit ffb29b1c255a ("mm/vmalloc: fix numa spreading for large hash tables") can cause significant performance regressions in some situations as Andrew mentioned in [1]. The main situation is vmalloc, vmalloc will allocate pages with NUMA_NO_NODE by default, that will result in alloc page one by one; In order to solve this, __alloc_pages_bulk and mempolicy should be considered at the same time. 1) If node is specified in memory allocation request, it will alloc all pages by __alloc_pages_bulk. 2) If interleaving allocate memory, it will cauculate how many pages should be allocated in each node, and use __alloc_pages_bulk to alloc pages in each node. [1]: https://lore.kernel.org/lkml/CALvZod4G3SzP3kWxQYn0fj+VgG-G3yWXz=gz17+3N57ru1iajw@mail.gmail.com/t/#m750c8e3231206134293b089feaa090590afa0f60 [akpm@linux-foundation.org: coding style fixes] [akpm@linux-foundation.org: make two functions static] [akpm@linux-foundation.org: fix CONFIG_NUMA=n build] Link: https://lkml.kernel.org/r/20211021080744.874701-3-chenwandun@huawei.com Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:53 +08:00
*/
if (IS_ENABLED(CONFIG_NUMA) && nid == NUMA_NO_NODE)
nr = alloc_pages_bulk_array_mempolicy_noprof(bulk_gfp,
mm/vmalloc: introduce alloc_pages_bulk_array_mempolicy to accelerate memory allocation Commit ffb29b1c255a ("mm/vmalloc: fix numa spreading for large hash tables") can cause significant performance regressions in some situations as Andrew mentioned in [1]. The main situation is vmalloc, vmalloc will allocate pages with NUMA_NO_NODE by default, that will result in alloc page one by one; In order to solve this, __alloc_pages_bulk and mempolicy should be considered at the same time. 1) If node is specified in memory allocation request, it will alloc all pages by __alloc_pages_bulk. 2) If interleaving allocate memory, it will cauculate how many pages should be allocated in each node, and use __alloc_pages_bulk to alloc pages in each node. [1]: https://lore.kernel.org/lkml/CALvZod4G3SzP3kWxQYn0fj+VgG-G3yWXz=gz17+3N57ru1iajw@mail.gmail.com/t/#m750c8e3231206134293b089feaa090590afa0f60 [akpm@linux-foundation.org: coding style fixes] [akpm@linux-foundation.org: make two functions static] [akpm@linux-foundation.org: fix CONFIG_NUMA=n build] Link: https://lkml.kernel.org/r/20211021080744.874701-3-chenwandun@huawei.com Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:53 +08:00
nr_pages_request,
pages + nr_allocated);
else
nr = alloc_pages_bulk_array_node_noprof(bulk_gfp, nid,
mm/vmalloc: introduce alloc_pages_bulk_array_mempolicy to accelerate memory allocation Commit ffb29b1c255a ("mm/vmalloc: fix numa spreading for large hash tables") can cause significant performance regressions in some situations as Andrew mentioned in [1]. The main situation is vmalloc, vmalloc will allocate pages with NUMA_NO_NODE by default, that will result in alloc page one by one; In order to solve this, __alloc_pages_bulk and mempolicy should be considered at the same time. 1) If node is specified in memory allocation request, it will alloc all pages by __alloc_pages_bulk. 2) If interleaving allocate memory, it will cauculate how many pages should be allocated in each node, and use __alloc_pages_bulk to alloc pages in each node. [1]: https://lore.kernel.org/lkml/CALvZod4G3SzP3kWxQYn0fj+VgG-G3yWXz=gz17+3N57ru1iajw@mail.gmail.com/t/#m750c8e3231206134293b089feaa090590afa0f60 [akpm@linux-foundation.org: coding style fixes] [akpm@linux-foundation.org: make two functions static] [akpm@linux-foundation.org: fix CONFIG_NUMA=n build] Link: https://lkml.kernel.org/r/20211021080744.874701-3-chenwandun@huawei.com Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:53 +08:00
nr_pages_request,
pages + nr_allocated);
nr_allocated += nr;
cond_resched();
/*
* If zero or pages were obtained partly,
* fallback to a single page allocator.
*/
if (nr != nr_pages_request)
break;
}
mm, vmalloc: fix high order __GFP_NOFAIL allocations Gao Xiang has reported that the page allocator complains about high order __GFP_NOFAIL request coming from the vmalloc core: __alloc_pages+0x1cb/0x5b0 mm/page_alloc.c:5549 alloc_pages+0x1aa/0x270 mm/mempolicy.c:2286 vm_area_alloc_pages mm/vmalloc.c:2989 [inline] __vmalloc_area_node mm/vmalloc.c:3057 [inline] __vmalloc_node_range+0x978/0x13c0 mm/vmalloc.c:3227 kvmalloc_node+0x156/0x1a0 mm/util.c:606 kvmalloc include/linux/slab.h:737 [inline] kvmalloc_array include/linux/slab.h:755 [inline] kvcalloc include/linux/slab.h:760 [inline] it seems that I have completely missed high order allocation backing vmalloc areas case when implementing __GFP_NOFAIL support. This means that [k]vmalloc at al. can allocate higher order allocations with __GFP_NOFAIL which can trigger OOM killer for non-costly orders easily or cause a lot of reclaim/compaction activity if those requests cannot be satisfied. Fix the issue by falling back to zero order allocations for __GFP_NOFAIL requests if the high order request fails. Link: https://lkml.kernel.org/r/ZAXynvdNqcI0f6Us@dhcp22.suse.cz Fixes: 9376130c390a ("mm/vmalloc: add support for __GFP_NOFAIL") Reported-by: Gao Xiang <hsiangkao@linux.alibaba.com> Link: https://lkml.kernel.org/r/20230305053035.1911-1-hsiangkao@linux.alibaba.com Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-06 16:15:17 +08:00
} else if (gfp & __GFP_NOFAIL) {
/*
* Higher order nofail allocations are really expensive and
* potentially dangerous (pre-mature OOM, disruptive reclaim
* and compaction etc.
*/
alloc_gfp &= ~__GFP_NOFAIL;
nofail = true;
mm/vmalloc: huge vmalloc backing pages should be split rather than compound Huge vmalloc higher-order backing pages were allocated with __GFP_COMP in order to allow the sub-pages to be refcounted by callers such as "remap_vmalloc_page [sic]" (remap_vmalloc_range). However a similar problem exists for other struct page fields callers use, for example fb_deferred_io_fault() takes a vmalloc'ed page and not only refcounts it but uses ->lru, ->mapping, ->index. This is not compatible with compound sub-pages, and can cause bad page state issues like BUG: Bad page state in process swapper/0 pfn:00743 page:(____ptrval____) refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x743 flags: 0x7ffff000000000(node=0|zone=0|lastcpupid=0x7ffff) raw: 007ffff000000000 c00c00000001d0c8 c00c00000001d0c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: corrupted mapping in tail page Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.18.0-rc3-00082-gfc6fff4a7ce1-dirty #2810 Call Trace: dump_stack_lvl+0x74/0xa8 (unreliable) bad_page+0x12c/0x170 free_tail_pages_check+0xe8/0x190 free_pcp_prepare+0x31c/0x4e0 free_unref_page+0x40/0x1b0 __vunmap+0x1d8/0x420 ... The correct approach is to use split high-order pages for the huge vmalloc backing. These allow callers to treat them in exactly the same way as individually-allocated order-0 pages. Link: https://lore.kernel.org/all/14444103-d51b-0fb3-ee63-c3f182f0b546@molgen.mpg.de/ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Paul Menzel <pmenzel@molgen.mpg.de> Cc: Song Liu <songliubraving@fb.com> Cc: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-04-22 14:01:05 +08:00
}
/* High-order pages or fallback path if "bulk" fails. */
mm/vmalloc: fix numa spreading for large hash tables Eric Dumazet reported a strange numa spreading info in [1], and found commit 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings") introduced this issue [2]. Dig into the difference before and after this patch, page allocation has some difference: before: alloc_large_system_hash __vmalloc __vmalloc_node(..., NUMA_NO_NODE, ...) __vmalloc_node_range __vmalloc_area_node alloc_page /* because NUMA_NO_NODE, so choose alloc_page branch */ alloc_pages_current alloc_page_interleave /* can be proved by print policy mode */ after: alloc_large_system_hash __vmalloc __vmalloc_node(..., NUMA_NO_NODE, ...) __vmalloc_node_range __vmalloc_area_node alloc_pages_node /* choose nid by nuam_mem_id() */ __alloc_pages_node(nid, ....) So after commit 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings"), it will allocate memory in current node instead of interleaving allocate memory. Link: https://lore.kernel.org/linux-mm/CANn89iL6AAyWhfxdHO+jaT075iOa3XcYn9k6JJc7JR2XYn6k_Q@mail.gmail.com/ [1] Link: https://lore.kernel.org/linux-mm/CANn89iLofTR=AK-QOZY87RdUZENCZUT4O6a0hvhu3_EwRMerOg@mail.gmail.com/ [2] Link: https://lkml.kernel.org/r/20211021080744.874701-2-chenwandun@huawei.com Fixes: 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reported-by: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Uladzislau Rezki <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-10-29 05:36:24 +08:00
while (nr_allocated < nr_pages) {
vmalloc: back off when the current task is OOM-killed Huge vmalloc allocation on heavy loaded node can lead to a global memory shortage. Task called vmalloc can have worst badness and be selected by OOM-killer, however taken fatal signal does not interrupt allocation cycle. Vmalloc repeat page allocaions again and again, exacerbating the crisis and consuming the memory freed up by another killed tasks. After a successful completion of the allocation procedure, a fatal signal will be processed and task will be destroyed finally. However it may not release the consumed memory, since the allocated object may have a lifetime unrelated to the completed task. In the worst case, this can lead to the host will panic due to "Out of memory and no killable processes..." This patch allows OOM-killer to break vmalloc cycle, makes OOM more effective and avoid host panic. It does not check oom condition directly, however, and breaks page allocation cycle when fatal signal was received. This may trigger some hidden problems, when caller does not handle vmalloc failures, or when rollaback after failed vmalloc calls own vmallocs inside. However all of these scenarios are incorrect: vmalloc does not guarantee successful allocation, it has never been called with __GFP_NOFAIL and threfore either should not be used for any rollbacks or should handle such errors correctly and not lead to critical failures. Link: https://lkml.kernel.org/r/83efc664-3a65-2adb-d7c4-2885784cf109@virtuozzo.com Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-06 04:39:37 +08:00
if (fatal_signal_pending(current))
break;
mm/vmalloc: fix numa spreading for large hash tables Eric Dumazet reported a strange numa spreading info in [1], and found commit 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings") introduced this issue [2]. Dig into the difference before and after this patch, page allocation has some difference: before: alloc_large_system_hash __vmalloc __vmalloc_node(..., NUMA_NO_NODE, ...) __vmalloc_node_range __vmalloc_area_node alloc_page /* because NUMA_NO_NODE, so choose alloc_page branch */ alloc_pages_current alloc_page_interleave /* can be proved by print policy mode */ after: alloc_large_system_hash __vmalloc __vmalloc_node(..., NUMA_NO_NODE, ...) __vmalloc_node_range __vmalloc_area_node alloc_pages_node /* choose nid by nuam_mem_id() */ __alloc_pages_node(nid, ....) So after commit 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings"), it will allocate memory in current node instead of interleaving allocate memory. Link: https://lore.kernel.org/linux-mm/CANn89iL6AAyWhfxdHO+jaT075iOa3XcYn9k6JJc7JR2XYn6k_Q@mail.gmail.com/ [1] Link: https://lore.kernel.org/linux-mm/CANn89iLofTR=AK-QOZY87RdUZENCZUT4O6a0hvhu3_EwRMerOg@mail.gmail.com/ [2] Link: https://lkml.kernel.org/r/20211021080744.874701-2-chenwandun@huawei.com Fixes: 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reported-by: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Uladzislau Rezki <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-10-29 05:36:24 +08:00
if (nid == NUMA_NO_NODE)
page = alloc_pages_noprof(alloc_gfp, order);
mm/vmalloc: fix numa spreading for large hash tables Eric Dumazet reported a strange numa spreading info in [1], and found commit 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings") introduced this issue [2]. Dig into the difference before and after this patch, page allocation has some difference: before: alloc_large_system_hash __vmalloc __vmalloc_node(..., NUMA_NO_NODE, ...) __vmalloc_node_range __vmalloc_area_node alloc_page /* because NUMA_NO_NODE, so choose alloc_page branch */ alloc_pages_current alloc_page_interleave /* can be proved by print policy mode */ after: alloc_large_system_hash __vmalloc __vmalloc_node(..., NUMA_NO_NODE, ...) __vmalloc_node_range __vmalloc_area_node alloc_pages_node /* choose nid by nuam_mem_id() */ __alloc_pages_node(nid, ....) So after commit 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings"), it will allocate memory in current node instead of interleaving allocate memory. Link: https://lore.kernel.org/linux-mm/CANn89iL6AAyWhfxdHO+jaT075iOa3XcYn9k6JJc7JR2XYn6k_Q@mail.gmail.com/ [1] Link: https://lore.kernel.org/linux-mm/CANn89iLofTR=AK-QOZY87RdUZENCZUT4O6a0hvhu3_EwRMerOg@mail.gmail.com/ [2] Link: https://lkml.kernel.org/r/20211021080744.874701-2-chenwandun@huawei.com Fixes: 121e6f3258fe ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reported-by: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Uladzislau Rezki <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-10-29 05:36:24 +08:00
else
page = alloc_pages_node_noprof(nid, alloc_gfp, order);
mm, vmalloc: fix high order __GFP_NOFAIL allocations Gao Xiang has reported that the page allocator complains about high order __GFP_NOFAIL request coming from the vmalloc core: __alloc_pages+0x1cb/0x5b0 mm/page_alloc.c:5549 alloc_pages+0x1aa/0x270 mm/mempolicy.c:2286 vm_area_alloc_pages mm/vmalloc.c:2989 [inline] __vmalloc_area_node mm/vmalloc.c:3057 [inline] __vmalloc_node_range+0x978/0x13c0 mm/vmalloc.c:3227 kvmalloc_node+0x156/0x1a0 mm/util.c:606 kvmalloc include/linux/slab.h:737 [inline] kvmalloc_array include/linux/slab.h:755 [inline] kvcalloc include/linux/slab.h:760 [inline] it seems that I have completely missed high order allocation backing vmalloc areas case when implementing __GFP_NOFAIL support. This means that [k]vmalloc at al. can allocate higher order allocations with __GFP_NOFAIL which can trigger OOM killer for non-costly orders easily or cause a lot of reclaim/compaction activity if those requests cannot be satisfied. Fix the issue by falling back to zero order allocations for __GFP_NOFAIL requests if the high order request fails. Link: https://lkml.kernel.org/r/ZAXynvdNqcI0f6Us@dhcp22.suse.cz Fixes: 9376130c390a ("mm/vmalloc: add support for __GFP_NOFAIL") Reported-by: Gao Xiang <hsiangkao@linux.alibaba.com> Link: https://lkml.kernel.org/r/20230305053035.1911-1-hsiangkao@linux.alibaba.com Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-06 16:15:17 +08:00
if (unlikely(!page)) {
if (!nofail)
break;
/* fall back to the zero order allocations */
alloc_gfp |= __GFP_NOFAIL;
order = 0;
continue;
}
mm/vmalloc: huge vmalloc backing pages should be split rather than compound Huge vmalloc higher-order backing pages were allocated with __GFP_COMP in order to allow the sub-pages to be refcounted by callers such as "remap_vmalloc_page [sic]" (remap_vmalloc_range). However a similar problem exists for other struct page fields callers use, for example fb_deferred_io_fault() takes a vmalloc'ed page and not only refcounts it but uses ->lru, ->mapping, ->index. This is not compatible with compound sub-pages, and can cause bad page state issues like BUG: Bad page state in process swapper/0 pfn:00743 page:(____ptrval____) refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x743 flags: 0x7ffff000000000(node=0|zone=0|lastcpupid=0x7ffff) raw: 007ffff000000000 c00c00000001d0c8 c00c00000001d0c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: corrupted mapping in tail page Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.18.0-rc3-00082-gfc6fff4a7ce1-dirty #2810 Call Trace: dump_stack_lvl+0x74/0xa8 (unreliable) bad_page+0x12c/0x170 free_tail_pages_check+0xe8/0x190 free_pcp_prepare+0x31c/0x4e0 free_unref_page+0x40/0x1b0 __vunmap+0x1d8/0x420 ... The correct approach is to use split high-order pages for the huge vmalloc backing. These allow callers to treat them in exactly the same way as individually-allocated order-0 pages. Link: https://lore.kernel.org/all/14444103-d51b-0fb3-ee63-c3f182f0b546@molgen.mpg.de/ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Paul Menzel <pmenzel@molgen.mpg.de> Cc: Song Liu <songliubraving@fb.com> Cc: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-04-22 14:01:05 +08:00
/*
* Higher order allocations must be able to be treated as
* indepdenent small pages by callers (as they can with
* small-page vmallocs). Some drivers do their own refcounting
* on vmalloc_to_page() pages, some use page->mapping,
* page->lru, etc.
*/
if (order)
split_page(page, order);
/*
* Careful, we allocate and map page-order pages, but
* tracking is done per PAGE_SIZE page so as to keep the
* vm_struct APIs independent of the physical/mapped size.
*/
for (i = 0; i < (1U << order); i++)
pages[nr_allocated + i] = page + i;
cond_resched();
nr_allocated += 1U << order;
}
return nr_allocated;
}
static void *__vmalloc_area_node(struct vm_struct *area, gfp_t gfp_mask,
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
pgprot_t prot, unsigned int page_shift,
int node)
{
const gfp_t nested_gfp = (gfp_mask & GFP_RECLAIM_MASK) | __GFP_ZERO;
bool nofail = gfp_mask & __GFP_NOFAIL;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
unsigned long addr = (unsigned long)area->addr;
unsigned long size = get_vm_area_size(area);
unsigned long array_size;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
unsigned int nr_small_pages = size >> PAGE_SHIFT;
unsigned int page_order;
mm/vmalloc: alloc GFP_NO{FS,IO} for vmalloc Patch series "extend vmalloc support for constrained allocations", v2. Based on a recent discussion with Dave and Neil [1] I have tried to implement NOFS, NOIO, NOFAIL support for the vmalloc to make life of kvmalloc users easier. A requirement for NOFAIL support for kvmalloc was new to me but this seems to be really needed by the xfs code. NOFS/NOIO was a known and a long term problem which was hoped to be handled by the scope API. Those scope should have been used at the reclaim recursion boundaries both to document them and also to remove the necessity of NOFS/NOIO constrains for all allocations within that scope. Instead workarounds were developed to wrap a single allocation instead (like ceph_kvmalloc). First patch implements NOFS/NOIO support for vmalloc. The second one adds NOFAIL support and the third one bundles all together into kvmalloc and drops ceph_kvmalloc which can use kvmalloc directly now. [1] http://lkml.kernel.org/r/163184741778.29351.16920832234899124642.stgit@noble.brown This patch (of 4): vmalloc historically hasn't supported GFP_NO{FS,IO} requests because page table allocations do not support externally provided gfp mask and performed GFP_KERNEL like allocations. Since few years we have scope (memalloc_no{fs,io}_{save,restore}) APIs to enforce NOFS and NOIO constrains implicitly to all allocators within the scope. There was a hope that those scopes would be defined on a higher level when the reclaim recursion boundary starts/stops (e.g. when a lock required during the memory reclaim is required etc.). It seems that not all NOFS/NOIO users have adopted this approach and instead they have taken a workaround approach to wrap a single [k]vmalloc allocation by a scope API. These workarounds do not serve the purpose of a better reclaim recursion documentation and reduction of explicit GFP_NO{FS,IO} usege so let's just provide them with the semantic they are asking for without a need for workarounds. Add support for GFP_NOFS and GFP_NOIO to vmalloc directly. All internal allocations already comply with the given gfp_mask. The only current exception is vmap_pages_range which maps kernel page tables. Infer the proper scope API based on the given gfp mask. [sfr@canb.auug.org.au: mm/vmalloc.c needs linux/sched/mm.h] Link: https://lkml.kernel.org/r/20211217232641.0148710c@canb.auug.org.au Link: https://lkml.kernel.org/r/20211122153233.9924-1-mhocko@kernel.org Link: https://lkml.kernel.org/r/20211122153233.9924-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Neil Brown <neilb@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Ilya Dryomov <idryomov@gmail.com> Cc: Jeff Layton <jlayton@kernel.org> Cc: Dave Chinner <dchinner@redhat.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-01-15 06:06:57 +08:00
unsigned int flags;
int ret;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
array_size = (unsigned long)nr_small_pages * sizeof(struct page *);
if (!(gfp_mask & (GFP_DMA | GFP_DMA32)))
gfp_mask |= __GFP_HIGHMEM;
/* Please note that the recursion is strictly bounded. */
if (array_size > PAGE_SIZE) {
area->pages = __vmalloc_node_noprof(array_size, 1, nested_gfp, node,
area->caller);
} else {
area->pages = kmalloc_node_noprof(array_size, nested_gfp, node);
}
mm/vmalloc: switch to bulk allocator in __vmalloc_area_node() Recently there has been introduced a page bulk allocator for users which need to get number of pages per one call request. For order-0 pages switch to an alloc_pages_bulk_array_node() instead of alloc_pages_node(), the reason is the former is not capable of allocating set of pages, thus a one call is per one page. Second, according to my tests the bulk allocator uses less cycles even for scenarios when only one page is requested. Running the "perf" on same test case shows below difference: <default> - 45.18% __vmalloc_node - __vmalloc_node_range - 35.60% __alloc_pages - get_page_from_freelist 3.36% __list_del_entry_valid 3.00% check_preemption_disabled 1.42% prep_new_page <default> <patch> - 31.00% __vmalloc_node - __vmalloc_node_range - 14.48% __alloc_pages_bulk 3.22% __list_del_entry_valid - 0.83% __alloc_pages get_page_from_freelist <patch> The "test_vmalloc.sh" also shows performance improvements: fix_size_alloc_test_4MB loops: 1000000 avg: 89105095 usec fix_size_alloc_test loops: 1000000 avg: 513672 usec full_fit_alloc_test loops: 1000000 avg: 748900 usec long_busy_list_alloc_test loops: 1000000 avg: 8043038 usec random_size_alloc_test loops: 1000000 avg: 4028582 usec fix_align_alloc_test loops: 1000000 avg: 1457671 usec fix_size_alloc_test_4MB loops: 1000000 avg: 62083711 usec fix_size_alloc_test loops: 1000000 avg: 449207 usec full_fit_alloc_test loops: 1000000 avg: 735985 usec long_busy_list_alloc_test loops: 1000000 avg: 5176052 usec random_size_alloc_test loops: 1000000 avg: 2589252 usec fix_align_alloc_test loops: 1000000 avg: 1365009 usec For example 4MB allocations illustrates ~30% gain, all the rest is also better. Link: https://lkml.kernel.org/r/20210516202056.2120-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Hillf Danton <hdanton@sina.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-29 10:40:14 +08:00
if (!area->pages) {
warn_alloc(gfp_mask, NULL,
"vmalloc error: size %lu, failed to allocated page array size %lu",
nr_small_pages * PAGE_SIZE, array_size);
free_vm_area(area);
return NULL;
}
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
set_vm_area_page_order(area, page_shift - PAGE_SHIFT);
page_order = vm_area_page_order(area);
area->nr_pages = vm_area_alloc_pages(gfp_mask | __GFP_NOWARN,
node, page_order, nr_small_pages, area->pages);
mm/vmalloc: switch to bulk allocator in __vmalloc_area_node() Recently there has been introduced a page bulk allocator for users which need to get number of pages per one call request. For order-0 pages switch to an alloc_pages_bulk_array_node() instead of alloc_pages_node(), the reason is the former is not capable of allocating set of pages, thus a one call is per one page. Second, according to my tests the bulk allocator uses less cycles even for scenarios when only one page is requested. Running the "perf" on same test case shows below difference: <default> - 45.18% __vmalloc_node - __vmalloc_node_range - 35.60% __alloc_pages - get_page_from_freelist 3.36% __list_del_entry_valid 3.00% check_preemption_disabled 1.42% prep_new_page <default> <patch> - 31.00% __vmalloc_node - __vmalloc_node_range - 14.48% __alloc_pages_bulk 3.22% __list_del_entry_valid - 0.83% __alloc_pages get_page_from_freelist <patch> The "test_vmalloc.sh" also shows performance improvements: fix_size_alloc_test_4MB loops: 1000000 avg: 89105095 usec fix_size_alloc_test loops: 1000000 avg: 513672 usec full_fit_alloc_test loops: 1000000 avg: 748900 usec long_busy_list_alloc_test loops: 1000000 avg: 8043038 usec random_size_alloc_test loops: 1000000 avg: 4028582 usec fix_align_alloc_test loops: 1000000 avg: 1457671 usec fix_size_alloc_test_4MB loops: 1000000 avg: 62083711 usec fix_size_alloc_test loops: 1000000 avg: 449207 usec full_fit_alloc_test loops: 1000000 avg: 735985 usec long_busy_list_alloc_test loops: 1000000 avg: 5176052 usec random_size_alloc_test loops: 1000000 avg: 2589252 usec fix_align_alloc_test loops: 1000000 avg: 1365009 usec For example 4MB allocations illustrates ~30% gain, all the rest is also better. Link: https://lkml.kernel.org/r/20210516202056.2120-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Hillf Danton <hdanton@sina.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-29 10:40:14 +08:00
atomic_long_add(area->nr_pages, &nr_vmalloc_pages);
if (gfp_mask & __GFP_ACCOUNT) {
mm/vmalloc: huge vmalloc backing pages should be split rather than compound Huge vmalloc higher-order backing pages were allocated with __GFP_COMP in order to allow the sub-pages to be refcounted by callers such as "remap_vmalloc_page [sic]" (remap_vmalloc_range). However a similar problem exists for other struct page fields callers use, for example fb_deferred_io_fault() takes a vmalloc'ed page and not only refcounts it but uses ->lru, ->mapping, ->index. This is not compatible with compound sub-pages, and can cause bad page state issues like BUG: Bad page state in process swapper/0 pfn:00743 page:(____ptrval____) refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x743 flags: 0x7ffff000000000(node=0|zone=0|lastcpupid=0x7ffff) raw: 007ffff000000000 c00c00000001d0c8 c00c00000001d0c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: corrupted mapping in tail page Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.18.0-rc3-00082-gfc6fff4a7ce1-dirty #2810 Call Trace: dump_stack_lvl+0x74/0xa8 (unreliable) bad_page+0x12c/0x170 free_tail_pages_check+0xe8/0x190 free_pcp_prepare+0x31c/0x4e0 free_unref_page+0x40/0x1b0 __vunmap+0x1d8/0x420 ... The correct approach is to use split high-order pages for the huge vmalloc backing. These allow callers to treat them in exactly the same way as individually-allocated order-0 pages. Link: https://lore.kernel.org/all/14444103-d51b-0fb3-ee63-c3f182f0b546@molgen.mpg.de/ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Paul Menzel <pmenzel@molgen.mpg.de> Cc: Song Liu <songliubraving@fb.com> Cc: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-04-22 14:01:05 +08:00
int i;
mm/vmalloc: huge vmalloc backing pages should be split rather than compound Huge vmalloc higher-order backing pages were allocated with __GFP_COMP in order to allow the sub-pages to be refcounted by callers such as "remap_vmalloc_page [sic]" (remap_vmalloc_range). However a similar problem exists for other struct page fields callers use, for example fb_deferred_io_fault() takes a vmalloc'ed page and not only refcounts it but uses ->lru, ->mapping, ->index. This is not compatible with compound sub-pages, and can cause bad page state issues like BUG: Bad page state in process swapper/0 pfn:00743 page:(____ptrval____) refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x743 flags: 0x7ffff000000000(node=0|zone=0|lastcpupid=0x7ffff) raw: 007ffff000000000 c00c00000001d0c8 c00c00000001d0c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: corrupted mapping in tail page Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.18.0-rc3-00082-gfc6fff4a7ce1-dirty #2810 Call Trace: dump_stack_lvl+0x74/0xa8 (unreliable) bad_page+0x12c/0x170 free_tail_pages_check+0xe8/0x190 free_pcp_prepare+0x31c/0x4e0 free_unref_page+0x40/0x1b0 __vunmap+0x1d8/0x420 ... The correct approach is to use split high-order pages for the huge vmalloc backing. These allow callers to treat them in exactly the same way as individually-allocated order-0 pages. Link: https://lore.kernel.org/all/14444103-d51b-0fb3-ee63-c3f182f0b546@molgen.mpg.de/ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Paul Menzel <pmenzel@molgen.mpg.de> Cc: Song Liu <songliubraving@fb.com> Cc: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-04-22 14:01:05 +08:00
for (i = 0; i < area->nr_pages; i++)
mod_memcg_page_state(area->pages[i], MEMCG_VMALLOC, 1);
}
mm/vmalloc: switch to bulk allocator in __vmalloc_area_node() Recently there has been introduced a page bulk allocator for users which need to get number of pages per one call request. For order-0 pages switch to an alloc_pages_bulk_array_node() instead of alloc_pages_node(), the reason is the former is not capable of allocating set of pages, thus a one call is per one page. Second, according to my tests the bulk allocator uses less cycles even for scenarios when only one page is requested. Running the "perf" on same test case shows below difference: <default> - 45.18% __vmalloc_node - __vmalloc_node_range - 35.60% __alloc_pages - get_page_from_freelist 3.36% __list_del_entry_valid 3.00% check_preemption_disabled 1.42% prep_new_page <default> <patch> - 31.00% __vmalloc_node - __vmalloc_node_range - 14.48% __alloc_pages_bulk 3.22% __list_del_entry_valid - 0.83% __alloc_pages get_page_from_freelist <patch> The "test_vmalloc.sh" also shows performance improvements: fix_size_alloc_test_4MB loops: 1000000 avg: 89105095 usec fix_size_alloc_test loops: 1000000 avg: 513672 usec full_fit_alloc_test loops: 1000000 avg: 748900 usec long_busy_list_alloc_test loops: 1000000 avg: 8043038 usec random_size_alloc_test loops: 1000000 avg: 4028582 usec fix_align_alloc_test loops: 1000000 avg: 1457671 usec fix_size_alloc_test_4MB loops: 1000000 avg: 62083711 usec fix_size_alloc_test loops: 1000000 avg: 449207 usec full_fit_alloc_test loops: 1000000 avg: 735985 usec long_busy_list_alloc_test loops: 1000000 avg: 5176052 usec random_size_alloc_test loops: 1000000 avg: 2589252 usec fix_align_alloc_test loops: 1000000 avg: 1365009 usec For example 4MB allocations illustrates ~30% gain, all the rest is also better. Link: https://lkml.kernel.org/r/20210516202056.2120-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Hillf Danton <hdanton@sina.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-29 10:40:14 +08:00
/*
* If not enough pages were obtained to accomplish an
* allocation request, free them via vfree() if any.
mm/vmalloc: switch to bulk allocator in __vmalloc_area_node() Recently there has been introduced a page bulk allocator for users which need to get number of pages per one call request. For order-0 pages switch to an alloc_pages_bulk_array_node() instead of alloc_pages_node(), the reason is the former is not capable of allocating set of pages, thus a one call is per one page. Second, according to my tests the bulk allocator uses less cycles even for scenarios when only one page is requested. Running the "perf" on same test case shows below difference: <default> - 45.18% __vmalloc_node - __vmalloc_node_range - 35.60% __alloc_pages - get_page_from_freelist 3.36% __list_del_entry_valid 3.00% check_preemption_disabled 1.42% prep_new_page <default> <patch> - 31.00% __vmalloc_node - __vmalloc_node_range - 14.48% __alloc_pages_bulk 3.22% __list_del_entry_valid - 0.83% __alloc_pages get_page_from_freelist <patch> The "test_vmalloc.sh" also shows performance improvements: fix_size_alloc_test_4MB loops: 1000000 avg: 89105095 usec fix_size_alloc_test loops: 1000000 avg: 513672 usec full_fit_alloc_test loops: 1000000 avg: 748900 usec long_busy_list_alloc_test loops: 1000000 avg: 8043038 usec random_size_alloc_test loops: 1000000 avg: 4028582 usec fix_align_alloc_test loops: 1000000 avg: 1457671 usec fix_size_alloc_test_4MB loops: 1000000 avg: 62083711 usec fix_size_alloc_test loops: 1000000 avg: 449207 usec full_fit_alloc_test loops: 1000000 avg: 735985 usec long_busy_list_alloc_test loops: 1000000 avg: 5176052 usec random_size_alloc_test loops: 1000000 avg: 2589252 usec fix_align_alloc_test loops: 1000000 avg: 1365009 usec For example 4MB allocations illustrates ~30% gain, all the rest is also better. Link: https://lkml.kernel.org/r/20210516202056.2120-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Hillf Danton <hdanton@sina.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-29 10:40:14 +08:00
*/
if (area->nr_pages != nr_small_pages) {
/*
* vm_area_alloc_pages() can fail due to insufficient memory but
* also:-
*
* - a pending fatal signal
* - insufficient huge page-order pages
*
* Since we always retry allocations at order-0 in the huge page
* case a warning for either is spurious.
*/
if (!fatal_signal_pending(current) && page_order == 0)
mm: vmalloc: avoid warn_alloc noise caused by fatal signal There're some suspicious warn_alloc on my test serer, for example, [13366.518837] warn_alloc: 81 callbacks suppressed [13366.518841] test_verifier: vmalloc error: size 4096, page order 0, failed to allocate pages, mode:0x500dc2(GFP_HIGHUSER|__GFP_ZERO|__GFP_ACCOUNT), nodemask=(null),cpuset=/,mems_allowed=0-1 [13366.522240] CPU: 30 PID: 722463 Comm: test_verifier Kdump: loaded Tainted: G W O 6.2.0+ #638 [13366.524216] Call Trace: [13366.524702] <TASK> [13366.525148] dump_stack_lvl+0x6c/0x80 [13366.525712] dump_stack+0x10/0x20 [13366.526239] warn_alloc+0x119/0x190 [13366.526783] ? alloc_pages_bulk_array_mempolicy+0x9e/0x2a0 [13366.527470] __vmalloc_area_node+0x546/0x5b0 [13366.528066] __vmalloc_node_range+0xc2/0x210 [13366.528660] __vmalloc_node+0x42/0x50 [13366.529186] ? bpf_prog_realloc+0x53/0xc0 [13366.529743] __vmalloc+0x1e/0x30 [13366.530235] bpf_prog_realloc+0x53/0xc0 [13366.530771] bpf_patch_insn_single+0x80/0x1b0 [13366.531351] bpf_jit_blind_constants+0xe9/0x1c0 [13366.531932] ? __free_pages+0xee/0x100 [13366.532457] ? free_large_kmalloc+0x58/0xb0 [13366.533002] bpf_int_jit_compile+0x8c/0x5e0 [13366.533546] bpf_prog_select_runtime+0xb4/0x100 [13366.534108] bpf_prog_load+0x6b1/0xa50 [13366.534610] ? perf_event_task_tick+0x96/0xb0 [13366.535151] ? security_capable+0x3a/0x60 [13366.535663] __sys_bpf+0xb38/0x2190 [13366.536120] ? kvm_clock_get_cycles+0x9/0x10 [13366.536643] __x64_sys_bpf+0x1c/0x30 [13366.537094] do_syscall_64+0x38/0x90 [13366.537554] entry_SYSCALL_64_after_hwframe+0x72/0xdc [13366.538107] RIP: 0033:0x7f78310f8e29 [13366.538561] Code: 01 00 48 81 c4 80 00 00 00 e9 f1 fe ff ff 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 17 e0 2c 00 f7 d8 64 89 01 48 [13366.540286] RSP: 002b:00007ffe2a61fff8 EFLAGS: 00000206 ORIG_RAX: 0000000000000141 [13366.541031] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f78310f8e29 [13366.541749] RDX: 0000000000000080 RSI: 00007ffe2a6200b0 RDI: 0000000000000005 [13366.542470] RBP: 00007ffe2a620010 R08: 00007ffe2a6202a0 R09: 00007ffe2a6200b0 [13366.543183] R10: 00000000000f423e R11: 0000000000000206 R12: 0000000000407800 [13366.543900] R13: 00007ffe2a620540 R14: 0000000000000000 R15: 0000000000000000 [13366.544623] </TASK> [13366.545260] Mem-Info: [13366.546121] active_anon:81319 inactive_anon:20733 isolated_anon:0 active_file:69450 inactive_file:5624 isolated_file:0 unevictable:0 dirty:10 writeback:0 slab_reclaimable:69649 slab_unreclaimable:48930 mapped:27400 shmem:12868 pagetables:4929 sec_pagetables:0 bounce:0 kernel_misc_reclaimable:0 free:15870308 free_pcp:142935 free_cma:0 [13366.551886] Node 0 active_anon:224836kB inactive_anon:33528kB active_file:175692kB inactive_file:13752kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:59248kB dirty:32kB writeback:0kB shmem:18252kB shmem_thp: 0kB shmem_pmdmapped: 0kB anon_thp: 0kB writeback_tmp:0kB kernel_stack:4616kB pagetables:10664kB sec_pagetables:0kB all_unreclaimable? no [13366.555184] Node 1 active_anon:100440kB inactive_anon:49404kB active_file:102108kB inactive_file:8744kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:50352kB dirty:8kB writeback:0kB shmem:33220kB shmem_thp: 0kB shmem_pmdmapped: 0kB anon_thp: 0kB writeback_tmp:0kB kernel_stack:3896kB pagetables:9052kB sec_pagetables:0kB all_unreclaimable? no [13366.558262] Node 0 DMA free:15360kB boost:0kB min:304kB low:380kB high:456kB reserved_highatomic:0KB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB writepending:0kB present:15992kB managed:15360kB mlocked:0kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB [13366.560821] lowmem_reserve[]: 0 2735 31873 31873 31873 [13366.561981] Node 0 DMA32 free:2790904kB boost:0kB min:56028kB low:70032kB high:84036kB reserved_highatomic:0KB active_anon:1936kB inactive_anon:20kB active_file:396kB inactive_file:344kB unevictable:0kB writepending:0kB present:3129200kB managed:2801520kB mlocked:0kB bounce:0kB free_pcp:5188kB local_pcp:0kB free_cma:0kB [13366.565148] lowmem_reserve[]: 0 0 29137 29137 29137 [13366.566168] Node 0 Normal free:28533824kB boost:0kB min:596740kB low:745924kB high:895108kB reserved_highatomic:28672KB active_anon:222900kB inactive_anon:33508kB active_file:175296kB inactive_file:13408kB unevictable:0kB writepending:32kB present:30408704kB managed:29837172kB mlocked:0kB bounce:0kB free_pcp:295724kB local_pcp:0kB free_cma:0kB [13366.569485] lowmem_reserve[]: 0 0 0 0 0 [13366.570416] Node 1 Normal free:32141144kB boost:0kB min:660504kB low:825628kB high:990752kB reserved_highatomic:69632KB active_anon:100440kB inactive_anon:49404kB active_file:102108kB inactive_file:8744kB unevictable:0kB writepending:8kB present:33554432kB managed:33025372kB mlocked:0kB bounce:0kB free_pcp:270880kB local_pcp:46860kB free_cma:0kB [13366.573403] lowmem_reserve[]: 0 0 0 0 0 [13366.574015] Node 0 DMA: 0*4kB 0*8kB 0*16kB 0*32kB 0*64kB 0*128kB 0*256kB 0*512kB 1*1024kB (U) 1*2048kB (M) 3*4096kB (M) = 15360kB [13366.575474] Node 0 DMA32: 782*4kB (UME) 756*8kB (UME) 736*16kB (UME) 745*32kB (UME) 694*64kB (UME) 653*128kB (UME) 595*256kB (UME) 552*512kB (UME) 454*1024kB (UME) 347*2048kB (UME) 246*4096kB (UME) = 2790904kB [13366.577442] Node 0 Normal: 33856*4kB (UMEH) 51815*8kB (UMEH) 42418*16kB (UMEH) 36272*32kB (UMEH) 22195*64kB (UMEH) 10296*128kB (UMEH) 7238*256kB (UMEH) 5638*512kB (UEH) 5337*1024kB (UMEH) 3506*2048kB (UMEH) 1470*4096kB (UME) = 28533784kB [13366.580460] Node 1 Normal: 15776*4kB (UMEH) 37485*8kB (UMEH) 29509*16kB (UMEH) 21420*32kB (UMEH) 14818*64kB (UMEH) 13051*128kB (UMEH) 9918*256kB (UMEH) 7374*512kB (UMEH) 5397*1024kB (UMEH) 3887*2048kB (UMEH) 2002*4096kB (UME) = 32141240kB [13366.583027] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=1048576kB [13366.584380] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=2048kB [13366.585702] Node 1 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=1048576kB [13366.587042] Node 1 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=2048kB [13366.588372] 87386 total pagecache pages [13366.589266] 0 pages in swap cache [13366.590327] Free swap = 0kB [13366.591227] Total swap = 0kB [13366.592142] 16777082 pages RAM [13366.593057] 0 pages HighMem/MovableOnly [13366.594037] 357226 pages reserved [13366.594979] 0 pages hwpoisoned This failure really confuse me as there're still lots of available pages. Finally I figured out it was caused by a fatal signal. When a process is allocating memory via vm_area_alloc_pages(), it will break directly even if it hasn't allocated the requested pages when it receives a fatal signal. In that case, we shouldn't show this warn_alloc, as it is useless. We only need to show this warning when there're really no enough pages. Link: https://lkml.kernel.org/r/20230330162625.13604-1-laoar.shao@gmail.com Signed-off-by: Yafang Shao <laoar.shao@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 00:26:25 +08:00
warn_alloc(gfp_mask, NULL,
"vmalloc error: size %lu, failed to allocate pages",
area->nr_pages * PAGE_SIZE);
mm/vmalloc: switch to bulk allocator in __vmalloc_area_node() Recently there has been introduced a page bulk allocator for users which need to get number of pages per one call request. For order-0 pages switch to an alloc_pages_bulk_array_node() instead of alloc_pages_node(), the reason is the former is not capable of allocating set of pages, thus a one call is per one page. Second, according to my tests the bulk allocator uses less cycles even for scenarios when only one page is requested. Running the "perf" on same test case shows below difference: <default> - 45.18% __vmalloc_node - __vmalloc_node_range - 35.60% __alloc_pages - get_page_from_freelist 3.36% __list_del_entry_valid 3.00% check_preemption_disabled 1.42% prep_new_page <default> <patch> - 31.00% __vmalloc_node - __vmalloc_node_range - 14.48% __alloc_pages_bulk 3.22% __list_del_entry_valid - 0.83% __alloc_pages get_page_from_freelist <patch> The "test_vmalloc.sh" also shows performance improvements: fix_size_alloc_test_4MB loops: 1000000 avg: 89105095 usec fix_size_alloc_test loops: 1000000 avg: 513672 usec full_fit_alloc_test loops: 1000000 avg: 748900 usec long_busy_list_alloc_test loops: 1000000 avg: 8043038 usec random_size_alloc_test loops: 1000000 avg: 4028582 usec fix_align_alloc_test loops: 1000000 avg: 1457671 usec fix_size_alloc_test_4MB loops: 1000000 avg: 62083711 usec fix_size_alloc_test loops: 1000000 avg: 449207 usec full_fit_alloc_test loops: 1000000 avg: 735985 usec long_busy_list_alloc_test loops: 1000000 avg: 5176052 usec random_size_alloc_test loops: 1000000 avg: 2589252 usec fix_align_alloc_test loops: 1000000 avg: 1365009 usec For example 4MB allocations illustrates ~30% gain, all the rest is also better. Link: https://lkml.kernel.org/r/20210516202056.2120-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Hillf Danton <hdanton@sina.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-29 10:40:14 +08:00
goto fail;
}
mm/vmalloc: alloc GFP_NO{FS,IO} for vmalloc Patch series "extend vmalloc support for constrained allocations", v2. Based on a recent discussion with Dave and Neil [1] I have tried to implement NOFS, NOIO, NOFAIL support for the vmalloc to make life of kvmalloc users easier. A requirement for NOFAIL support for kvmalloc was new to me but this seems to be really needed by the xfs code. NOFS/NOIO was a known and a long term problem which was hoped to be handled by the scope API. Those scope should have been used at the reclaim recursion boundaries both to document them and also to remove the necessity of NOFS/NOIO constrains for all allocations within that scope. Instead workarounds were developed to wrap a single allocation instead (like ceph_kvmalloc). First patch implements NOFS/NOIO support for vmalloc. The second one adds NOFAIL support and the third one bundles all together into kvmalloc and drops ceph_kvmalloc which can use kvmalloc directly now. [1] http://lkml.kernel.org/r/163184741778.29351.16920832234899124642.stgit@noble.brown This patch (of 4): vmalloc historically hasn't supported GFP_NO{FS,IO} requests because page table allocations do not support externally provided gfp mask and performed GFP_KERNEL like allocations. Since few years we have scope (memalloc_no{fs,io}_{save,restore}) APIs to enforce NOFS and NOIO constrains implicitly to all allocators within the scope. There was a hope that those scopes would be defined on a higher level when the reclaim recursion boundary starts/stops (e.g. when a lock required during the memory reclaim is required etc.). It seems that not all NOFS/NOIO users have adopted this approach and instead they have taken a workaround approach to wrap a single [k]vmalloc allocation by a scope API. These workarounds do not serve the purpose of a better reclaim recursion documentation and reduction of explicit GFP_NO{FS,IO} usege so let's just provide them with the semantic they are asking for without a need for workarounds. Add support for GFP_NOFS and GFP_NOIO to vmalloc directly. All internal allocations already comply with the given gfp_mask. The only current exception is vmap_pages_range which maps kernel page tables. Infer the proper scope API based on the given gfp mask. [sfr@canb.auug.org.au: mm/vmalloc.c needs linux/sched/mm.h] Link: https://lkml.kernel.org/r/20211217232641.0148710c@canb.auug.org.au Link: https://lkml.kernel.org/r/20211122153233.9924-1-mhocko@kernel.org Link: https://lkml.kernel.org/r/20211122153233.9924-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Neil Brown <neilb@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Ilya Dryomov <idryomov@gmail.com> Cc: Jeff Layton <jlayton@kernel.org> Cc: Dave Chinner <dchinner@redhat.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-01-15 06:06:57 +08:00
/*
* page tables allocations ignore external gfp mask, enforce it
* by the scope API
*/
if ((gfp_mask & (__GFP_FS | __GFP_IO)) == __GFP_IO)
flags = memalloc_nofs_save();
else if ((gfp_mask & (__GFP_FS | __GFP_IO)) == 0)
flags = memalloc_noio_save();
do {
ret = vmap_pages_range(addr, addr + size, prot, area->pages,
mm/vmalloc: alloc GFP_NO{FS,IO} for vmalloc Patch series "extend vmalloc support for constrained allocations", v2. Based on a recent discussion with Dave and Neil [1] I have tried to implement NOFS, NOIO, NOFAIL support for the vmalloc to make life of kvmalloc users easier. A requirement for NOFAIL support for kvmalloc was new to me but this seems to be really needed by the xfs code. NOFS/NOIO was a known and a long term problem which was hoped to be handled by the scope API. Those scope should have been used at the reclaim recursion boundaries both to document them and also to remove the necessity of NOFS/NOIO constrains for all allocations within that scope. Instead workarounds were developed to wrap a single allocation instead (like ceph_kvmalloc). First patch implements NOFS/NOIO support for vmalloc. The second one adds NOFAIL support and the third one bundles all together into kvmalloc and drops ceph_kvmalloc which can use kvmalloc directly now. [1] http://lkml.kernel.org/r/163184741778.29351.16920832234899124642.stgit@noble.brown This patch (of 4): vmalloc historically hasn't supported GFP_NO{FS,IO} requests because page table allocations do not support externally provided gfp mask and performed GFP_KERNEL like allocations. Since few years we have scope (memalloc_no{fs,io}_{save,restore}) APIs to enforce NOFS and NOIO constrains implicitly to all allocators within the scope. There was a hope that those scopes would be defined on a higher level when the reclaim recursion boundary starts/stops (e.g. when a lock required during the memory reclaim is required etc.). It seems that not all NOFS/NOIO users have adopted this approach and instead they have taken a workaround approach to wrap a single [k]vmalloc allocation by a scope API. These workarounds do not serve the purpose of a better reclaim recursion documentation and reduction of explicit GFP_NO{FS,IO} usege so let's just provide them with the semantic they are asking for without a need for workarounds. Add support for GFP_NOFS and GFP_NOIO to vmalloc directly. All internal allocations already comply with the given gfp_mask. The only current exception is vmap_pages_range which maps kernel page tables. Infer the proper scope API based on the given gfp mask. [sfr@canb.auug.org.au: mm/vmalloc.c needs linux/sched/mm.h] Link: https://lkml.kernel.org/r/20211217232641.0148710c@canb.auug.org.au Link: https://lkml.kernel.org/r/20211122153233.9924-1-mhocko@kernel.org Link: https://lkml.kernel.org/r/20211122153233.9924-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Neil Brown <neilb@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Ilya Dryomov <idryomov@gmail.com> Cc: Jeff Layton <jlayton@kernel.org> Cc: Dave Chinner <dchinner@redhat.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-01-15 06:06:57 +08:00
page_shift);
if (nofail && (ret < 0))
schedule_timeout_uninterruptible(1);
} while (nofail && (ret < 0));
mm/vmalloc: alloc GFP_NO{FS,IO} for vmalloc Patch series "extend vmalloc support for constrained allocations", v2. Based on a recent discussion with Dave and Neil [1] I have tried to implement NOFS, NOIO, NOFAIL support for the vmalloc to make life of kvmalloc users easier. A requirement for NOFAIL support for kvmalloc was new to me but this seems to be really needed by the xfs code. NOFS/NOIO was a known and a long term problem which was hoped to be handled by the scope API. Those scope should have been used at the reclaim recursion boundaries both to document them and also to remove the necessity of NOFS/NOIO constrains for all allocations within that scope. Instead workarounds were developed to wrap a single allocation instead (like ceph_kvmalloc). First patch implements NOFS/NOIO support for vmalloc. The second one adds NOFAIL support and the third one bundles all together into kvmalloc and drops ceph_kvmalloc which can use kvmalloc directly now. [1] http://lkml.kernel.org/r/163184741778.29351.16920832234899124642.stgit@noble.brown This patch (of 4): vmalloc historically hasn't supported GFP_NO{FS,IO} requests because page table allocations do not support externally provided gfp mask and performed GFP_KERNEL like allocations. Since few years we have scope (memalloc_no{fs,io}_{save,restore}) APIs to enforce NOFS and NOIO constrains implicitly to all allocators within the scope. There was a hope that those scopes would be defined on a higher level when the reclaim recursion boundary starts/stops (e.g. when a lock required during the memory reclaim is required etc.). It seems that not all NOFS/NOIO users have adopted this approach and instead they have taken a workaround approach to wrap a single [k]vmalloc allocation by a scope API. These workarounds do not serve the purpose of a better reclaim recursion documentation and reduction of explicit GFP_NO{FS,IO} usege so let's just provide them with the semantic they are asking for without a need for workarounds. Add support for GFP_NOFS and GFP_NOIO to vmalloc directly. All internal allocations already comply with the given gfp_mask. The only current exception is vmap_pages_range which maps kernel page tables. Infer the proper scope API based on the given gfp mask. [sfr@canb.auug.org.au: mm/vmalloc.c needs linux/sched/mm.h] Link: https://lkml.kernel.org/r/20211217232641.0148710c@canb.auug.org.au Link: https://lkml.kernel.org/r/20211122153233.9924-1-mhocko@kernel.org Link: https://lkml.kernel.org/r/20211122153233.9924-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Neil Brown <neilb@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Ilya Dryomov <idryomov@gmail.com> Cc: Jeff Layton <jlayton@kernel.org> Cc: Dave Chinner <dchinner@redhat.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-01-15 06:06:57 +08:00
if ((gfp_mask & (__GFP_FS | __GFP_IO)) == __GFP_IO)
memalloc_nofs_restore(flags);
else if ((gfp_mask & (__GFP_FS | __GFP_IO)) == 0)
memalloc_noio_restore(flags);
if (ret < 0) {
warn_alloc(gfp_mask, NULL,
"vmalloc error: size %lu, failed to map pages",
area->nr_pages * PAGE_SIZE);
goto fail;
}
2020-06-02 12:51:19 +08:00
return area->addr;
fail:
vfree(area->addr);
return NULL;
}
/**
* __vmalloc_node_range - allocate virtually contiguous memory
* @size: allocation size
* @align: desired alignment
* @start: vm area range start
* @end: vm area range end
* @gfp_mask: flags for the page level allocator
* @prot: protection mask for the allocated pages
* @vm_flags: additional vm area flags (e.g. %VM_NO_GUARD)
* @node: node to use for allocation or NUMA_NO_NODE
* @caller: caller's return address
*
* Allocate enough pages to cover @size from the page level
* allocator with @gfp_mask flags. Please note that the full set of gfp
* flags are not supported. GFP_KERNEL, GFP_NOFS and GFP_NOIO are all
* supported.
* Zone modifiers are not supported. From the reclaim modifiers
* __GFP_DIRECT_RECLAIM is required (aka GFP_NOWAIT is not supported)
* and only __GFP_NOFAIL is supported (i.e. __GFP_NORETRY and
* __GFP_RETRY_MAYFAIL are not supported).
*
* __GFP_NOWARN can be used to suppress failures messages.
*
* Map them into contiguous kernel virtual space, using a pagetable
* protection of @prot.
*
* Return: the address of the area or %NULL on failure
*/
void *__vmalloc_node_range_noprof(unsigned long size, unsigned long align,
unsigned long start, unsigned long end, gfp_t gfp_mask,
mm: vmalloc: pass additional vm_flags to __vmalloc_node_range() For instrumenting global variables KASan will shadow memory backing memory for modules. So on module loading we will need to allocate memory for shadow and map it at address in shadow that corresponds to the address allocated in module_alloc(). __vmalloc_node_range() could be used for this purpose, except it puts a guard hole after allocated area. Guard hole in shadow memory should be a problem because at some future point we might need to have a shadow memory at address occupied by guard hole. So we could fail to allocate shadow for module_alloc(). Now we have VM_NO_GUARD flag disabling guard page, so we need to pass into __vmalloc_node_range(). Add new parameter 'vm_flags' to __vmalloc_node_range() function. Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-02-14 06:40:07 +08:00
pgprot_t prot, unsigned long vm_flags, int node,
const void *caller)
{
struct vm_struct *area;
void *ret;
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
kasan_vmalloc_flags_t kasan_flags = KASAN_VMALLOC_NONE;
unsigned long real_size = size;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
unsigned long real_align = align;
unsigned int shift = PAGE_SHIFT;
if (WARN_ON_ONCE(!size))
return NULL;
if ((size >> PAGE_SHIFT) > totalram_pages()) {
warn_alloc(gfp_mask, NULL,
"vmalloc error: size %lu, exceeds total pages",
real_size);
return NULL;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
}
if (vmap_allow_huge && (vm_flags & VM_ALLOW_HUGE_VMAP)) {
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
unsigned long size_per_node;
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
/*
* Try huge pages. Only try for PAGE_KERNEL allocations,
* others like modules don't yet expect huge pages in
* their allocations due to apply_to_page_range not
* supporting them.
*/
size_per_node = size;
if (node == NUMA_NO_NODE)
size_per_node /= num_online_nodes();
if (arch_vmap_pmd_supported(prot) && size_per_node >= PMD_SIZE)
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
shift = PMD_SHIFT;
else
shift = arch_vmap_pte_supported_shift(size_per_node);
align = max(real_align, 1UL << shift);
size = ALIGN(real_size, 1UL << shift);
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
}
again:
area = __get_vm_area_node(real_size, align, shift, VM_ALLOC |
VM_UNINITIALIZED | vm_flags, start, end, node,
gfp_mask, caller);
if (!area) {
bool nofail = gfp_mask & __GFP_NOFAIL;
warn_alloc(gfp_mask, NULL,
"vmalloc error: size %lu, vm_struct allocation failed%s",
real_size, (nofail) ? ". Retrying." : "");
if (nofail) {
schedule_timeout_uninterruptible(1);
goto again;
}
goto fail;
}
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
/*
* Prepare arguments for __vmalloc_area_node() and
* kasan_unpoison_vmalloc().
*/
if (pgprot_val(prot) == pgprot_val(PAGE_KERNEL)) {
if (kasan_hw_tags_enabled()) {
/*
* Modify protection bits to allow tagging.
* This must be done before mapping.
*/
prot = arch_vmap_pgprot_tagged(prot);
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
/*
* Skip page_alloc poisoning and zeroing for physical
* pages backing VM_ALLOC mapping. Memory is instead
* poisoned and zeroed by kasan_unpoison_vmalloc().
*/
gfp_mask |= __GFP_SKIP_KASAN | __GFP_SKIP_ZERO;
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
}
/* Take note that the mapping is PAGE_KERNEL. */
kasan_flags |= KASAN_VMALLOC_PROT_NORMAL;
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
}
/* Allocate physical pages and map them into vmalloc space. */
ret = __vmalloc_area_node(area, gfp_mask, prot, shift, node);
if (!ret)
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
goto fail;
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
/*
* Mark the pages as accessible, now that they are mapped.
* The condition for setting KASAN_VMALLOC_INIT should complement the
* one in post_alloc_hook() with regards to the __GFP_SKIP_ZERO check
* to make sure that memory is initialized under the same conditions.
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
* Tag-based KASAN modes only assign tags to normal non-executable
* allocations, see __kasan_unpoison_vmalloc().
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
*/
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
kasan_flags |= KASAN_VMALLOC_VM_ALLOC;
if (!want_init_on_free() && want_init_on_alloc(gfp_mask) &&
(gfp_mask & __GFP_SKIP_ZERO))
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
kasan_flags |= KASAN_VMALLOC_INIT;
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
/* KASAN_VMALLOC_PROT_NORMAL already set if required. */
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
area->addr = kasan_unpoison_vmalloc(area->addr, real_size, kasan_flags);
/*
* In this function, newly allocated vm_struct has VM_UNINITIALIZED
* flag. It means that vm_struct is not fully initialized.
* Now, it is fully initialized, so remove this flag here.
*/
clear_vm_uninitialized_flag(area);
size = PAGE_ALIGN(size);
mm: defer kmemleak object creation of module_alloc() Yongqiang reports a kmemleak panic when module insmod/rmmod with KASAN enabled(without KASAN_VMALLOC) on x86[1]. When the module area allocates memory, it's kmemleak_object is created successfully, but the KASAN shadow memory of module allocation is not ready, so when kmemleak scan the module's pointer, it will panic due to no shadow memory with KASAN check. module_alloc __vmalloc_node_range kmemleak_vmalloc kmemleak_scan update_checksum kasan_module_alloc kmemleak_ignore Note, there is no problem if KASAN_VMALLOC enabled, the modules area entire shadow memory is preallocated. Thus, the bug only exits on ARCH which supports dynamic allocation of module area per module load, for now, only x86/arm64/s390 are involved. Add a VM_DEFER_KMEMLEAK flags, defer vmalloc'ed object register of kmemleak in module_alloc() to fix this issue. [1] https://lore.kernel.org/all/6d41e2b9-4692-5ec4-b1cd-cbe29ae89739@huawei.com/ [wangkefeng.wang@huawei.com: fix build] Link: https://lkml.kernel.org/r/20211125080307.27225-1-wangkefeng.wang@huawei.com [akpm@linux-foundation.org: simplify ifdefs, per Andrey] Link: https://lkml.kernel.org/r/CA+fCnZcnwJHUQq34VuRxpdoY6_XbJCDJ-jopksS5Eia4PijPzw@mail.gmail.com Link: https://lkml.kernel.org/r/20211124142034.192078-1-wangkefeng.wang@huawei.com Fixes: 793213a82de4 ("s390/kasan: dynamic shadow mem allocation for modules") Fixes: 39d114ddc682 ("arm64: add KASAN support") Fixes: bebf56a1b176 ("kasan: enable instrumentation of global variables") Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: Yongqiang Liu <liuyongqiang13@huawei.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Christian Borntraeger <borntraeger@linux.ibm.com> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-01-15 06:04:11 +08:00
if (!(vm_flags & VM_DEFER_KMEMLEAK))
kmemleak_vmalloc(area, size, gfp_mask);
return area->addr;
fail:
mm/vmalloc: hugepage vmalloc mappings Support huge page vmalloc mappings. Config option HAVE_ARCH_HUGE_VMALLOC enables support on architectures that define HAVE_ARCH_HUGE_VMAP and supports PMD sized vmap mappings. vmalloc will attempt to allocate PMD-sized pages if allocating PMD size or larger, and fall back to small pages if that was unsuccessful. Architectures must ensure that any arch specific vmalloc allocations that require PAGE_SIZE mappings (e.g., module allocations vs strict module rwx) use the VM_NOHUGE flag to inhibit larger mappings. This can result in more internal fragmentation and memory overhead for a given allocation, an option nohugevmalloc is added to disable at boot. [colin.king@canonical.com: fix read of uninitialized pointer area] Link: https://lkml.kernel.org/r/20210318155955.18220-1-colin.king@canonical.com Link: https://lkml.kernel.org/r/20210317062402.533919-14-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Russell King <linux@armlinux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-04-30 13:58:49 +08:00
if (shift > PAGE_SHIFT) {
shift = PAGE_SHIFT;
align = real_align;
size = real_size;
goto again;
}
return NULL;
}
/**
* __vmalloc_node - allocate virtually contiguous memory
* @size: allocation size
* @align: desired alignment
* @gfp_mask: flags for the page level allocator
* @node: node to use for allocation or NUMA_NO_NODE
* @caller: caller's return address
mm: introduce kv[mz]alloc helpers Patch series "kvmalloc", v5. There are many open coded kmalloc with vmalloc fallback instances in the tree. Most of them are not careful enough or simply do not care about the underlying semantic of the kmalloc/page allocator which means that a) some vmalloc fallbacks are basically unreachable because the kmalloc part will keep retrying until it succeeds b) the page allocator can invoke a really disruptive steps like the OOM killer to move forward which doesn't sound appropriate when we consider that the vmalloc fallback is available. As it can be seen implementing kvmalloc requires quite an intimate knowledge if the page allocator and the memory reclaim internals which strongly suggests that a helper should be implemented in the memory subsystem proper. Most callers, I could find, have been converted to use the helper instead. This is patch 6. There are some more relying on __GFP_REPEAT in the networking stack which I have converted as well and Eric Dumazet was not opposed [2] to convert them as well. [1] http://lkml.kernel.org/r/20170130094940.13546-1-mhocko@kernel.org [2] http://lkml.kernel.org/r/1485273626.16328.301.camel@edumazet-glaptop3.roam.corp.google.com This patch (of 9): Using kmalloc with the vmalloc fallback for larger allocations is a common pattern in the kernel code. Yet we do not have any common helper for that and so users have invented their own helpers. Some of them are really creative when doing so. Let's just add kv[mz]alloc and make sure it is implemented properly. This implementation makes sure to not make a large memory pressure for > PAGE_SZE requests (__GFP_NORETRY) and also to not warn about allocation failures. This also rules out the OOM killer as the vmalloc is a more approapriate fallback than a disruptive user visible action. This patch also changes some existing users and removes helpers which are specific for them. In some cases this is not possible (e.g. ext4_kvmalloc, libcfs_kvzalloc) because those seems to be broken and require GFP_NO{FS,IO} context which is not vmalloc compatible in general (note that the page table allocation is GFP_KERNEL). Those need to be fixed separately. While we are at it, document that __vmalloc{_node} about unsupported gfp mask because there seems to be a lot of confusion out there. kvmalloc_node will warn about GFP_KERNEL incompatible (which are not superset) flags to catch new abusers. Existing ones would have to die slowly. [sfr@canb.auug.org.au: f2fs fixup] Link: http://lkml.kernel.org/r/20170320163735.332e64b7@canb.auug.org.au Link: http://lkml.kernel.org/r/20170306103032.2540-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Andreas Dilger <adilger@dilger.ca> [ext4 part] Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: John Hubbard <jhubbard@nvidia.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-05-09 06:57:09 +08:00
*
* Allocate enough pages to cover @size from the page level allocator with
* @gfp_mask flags. Map them into contiguous kernel virtual space.
mm: introduce kv[mz]alloc helpers Patch series "kvmalloc", v5. There are many open coded kmalloc with vmalloc fallback instances in the tree. Most of them are not careful enough or simply do not care about the underlying semantic of the kmalloc/page allocator which means that a) some vmalloc fallbacks are basically unreachable because the kmalloc part will keep retrying until it succeeds b) the page allocator can invoke a really disruptive steps like the OOM killer to move forward which doesn't sound appropriate when we consider that the vmalloc fallback is available. As it can be seen implementing kvmalloc requires quite an intimate knowledge if the page allocator and the memory reclaim internals which strongly suggests that a helper should be implemented in the memory subsystem proper. Most callers, I could find, have been converted to use the helper instead. This is patch 6. There are some more relying on __GFP_REPEAT in the networking stack which I have converted as well and Eric Dumazet was not opposed [2] to convert them as well. [1] http://lkml.kernel.org/r/20170130094940.13546-1-mhocko@kernel.org [2] http://lkml.kernel.org/r/1485273626.16328.301.camel@edumazet-glaptop3.roam.corp.google.com This patch (of 9): Using kmalloc with the vmalloc fallback for larger allocations is a common pattern in the kernel code. Yet we do not have any common helper for that and so users have invented their own helpers. Some of them are really creative when doing so. Let's just add kv[mz]alloc and make sure it is implemented properly. This implementation makes sure to not make a large memory pressure for > PAGE_SZE requests (__GFP_NORETRY) and also to not warn about allocation failures. This also rules out the OOM killer as the vmalloc is a more approapriate fallback than a disruptive user visible action. This patch also changes some existing users and removes helpers which are specific for them. In some cases this is not possible (e.g. ext4_kvmalloc, libcfs_kvzalloc) because those seems to be broken and require GFP_NO{FS,IO} context which is not vmalloc compatible in general (note that the page table allocation is GFP_KERNEL). Those need to be fixed separately. While we are at it, document that __vmalloc{_node} about unsupported gfp mask because there seems to be a lot of confusion out there. kvmalloc_node will warn about GFP_KERNEL incompatible (which are not superset) flags to catch new abusers. Existing ones would have to die slowly. [sfr@canb.auug.org.au: f2fs fixup] Link: http://lkml.kernel.org/r/20170320163735.332e64b7@canb.auug.org.au Link: http://lkml.kernel.org/r/20170306103032.2540-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Andreas Dilger <adilger@dilger.ca> [ext4 part] Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: John Hubbard <jhubbard@nvidia.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-05-09 06:57:09 +08:00
*
* Reclaim modifiers in @gfp_mask - __GFP_NORETRY, __GFP_RETRY_MAYFAIL
* and __GFP_NOFAIL are not supported
mm: introduce kv[mz]alloc helpers Patch series "kvmalloc", v5. There are many open coded kmalloc with vmalloc fallback instances in the tree. Most of them are not careful enough or simply do not care about the underlying semantic of the kmalloc/page allocator which means that a) some vmalloc fallbacks are basically unreachable because the kmalloc part will keep retrying until it succeeds b) the page allocator can invoke a really disruptive steps like the OOM killer to move forward which doesn't sound appropriate when we consider that the vmalloc fallback is available. As it can be seen implementing kvmalloc requires quite an intimate knowledge if the page allocator and the memory reclaim internals which strongly suggests that a helper should be implemented in the memory subsystem proper. Most callers, I could find, have been converted to use the helper instead. This is patch 6. There are some more relying on __GFP_REPEAT in the networking stack which I have converted as well and Eric Dumazet was not opposed [2] to convert them as well. [1] http://lkml.kernel.org/r/20170130094940.13546-1-mhocko@kernel.org [2] http://lkml.kernel.org/r/1485273626.16328.301.camel@edumazet-glaptop3.roam.corp.google.com This patch (of 9): Using kmalloc with the vmalloc fallback for larger allocations is a common pattern in the kernel code. Yet we do not have any common helper for that and so users have invented their own helpers. Some of them are really creative when doing so. Let's just add kv[mz]alloc and make sure it is implemented properly. This implementation makes sure to not make a large memory pressure for > PAGE_SZE requests (__GFP_NORETRY) and also to not warn about allocation failures. This also rules out the OOM killer as the vmalloc is a more approapriate fallback than a disruptive user visible action. This patch also changes some existing users and removes helpers which are specific for them. In some cases this is not possible (e.g. ext4_kvmalloc, libcfs_kvzalloc) because those seems to be broken and require GFP_NO{FS,IO} context which is not vmalloc compatible in general (note that the page table allocation is GFP_KERNEL). Those need to be fixed separately. While we are at it, document that __vmalloc{_node} about unsupported gfp mask because there seems to be a lot of confusion out there. kvmalloc_node will warn about GFP_KERNEL incompatible (which are not superset) flags to catch new abusers. Existing ones would have to die slowly. [sfr@canb.auug.org.au: f2fs fixup] Link: http://lkml.kernel.org/r/20170320163735.332e64b7@canb.auug.org.au Link: http://lkml.kernel.org/r/20170306103032.2540-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Andreas Dilger <adilger@dilger.ca> [ext4 part] Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: John Hubbard <jhubbard@nvidia.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-05-09 06:57:09 +08:00
*
* Any use of gfp flags outside of GFP_KERNEL should be consulted
* with mm people.
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *__vmalloc_node_noprof(unsigned long size, unsigned long align,
gfp_t gfp_mask, int node, const void *caller)
{
return __vmalloc_node_range_noprof(size, align, VMALLOC_START, VMALLOC_END,
gfp_mask, PAGE_KERNEL, 0, node, caller);
}
mm: switch the test_vmalloc module to use __vmalloc_node No need to export the very low-level __vmalloc_node_range when the test module can use a slightly higher level variant. [akpm@linux-foundation.org: add missing `node' arg] [akpm@linux-foundation.org: fix riscv nommu build] Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-26-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:57 +08:00
/*
* This is only for performance analysis of vmalloc and stress purpose.
* It is required by vmalloc test module, therefore do not use it other
* than that.
*/
#ifdef CONFIG_TEST_VMALLOC_MODULE
EXPORT_SYMBOL_GPL(__vmalloc_node_noprof);
mm: switch the test_vmalloc module to use __vmalloc_node No need to export the very low-level __vmalloc_node_range when the test module can use a slightly higher level variant. [akpm@linux-foundation.org: add missing `node' arg] [akpm@linux-foundation.org: fix riscv nommu build] Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-26-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:57 +08:00
#endif
void *__vmalloc_noprof(unsigned long size, gfp_t gfp_mask)
{
return __vmalloc_node_noprof(size, 1, gfp_mask, NUMA_NO_NODE,
vmallocinfo: add caller information Add caller information so that /proc/vmallocinfo shows where the allocation request for a slice of vmalloc memory originated. Results in output like this: 0xffffc20000000000-0xffffc20000801000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20000801000-0xffffc20000806000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000806000-0xffffc20000c07000 4198400 alloc_large_system_hash+0x127/0x246 pages=1024 vmalloc vpages 0xffffc20000c07000-0xffffc20000c0a000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c0a000-0xffffc20000c0c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c0c000-0xffffc20000c0f000 12288 acpi_os_map_memory+0x13/0x1c phys=cff64000 ioremap 0xffffc20000c10000-0xffffc20000c15000 20480 acpi_os_map_memory+0x13/0x1c phys=cff65000 ioremap 0xffffc20000c16000-0xffffc20000c18000 8192 acpi_os_map_memory+0x13/0x1c phys=cff69000 ioremap 0xffffc20000c18000-0xffffc20000c1a000 8192 acpi_os_map_memory+0x13/0x1c phys=fed1f000 ioremap 0xffffc20000c1a000-0xffffc20000c1c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1c000-0xffffc20000c1e000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1e000-0xffffc20000c20000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c20000-0xffffc20000c22000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c22000-0xffffc20000c24000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c24000-0xffffc20000c26000 8192 acpi_os_map_memory+0x13/0x1c phys=e0081000 ioremap 0xffffc20000c26000-0xffffc20000c28000 8192 acpi_os_map_memory+0x13/0x1c phys=e0080000 ioremap 0xffffc20000c28000-0xffffc20000c2d000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000c2d000-0xffffc20000c31000 16384 tcp_init+0xd5/0x31c pages=3 vmalloc 0xffffc20000c31000-0xffffc20000c34000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c34000-0xffffc20000c36000 8192 init_vdso_vars+0xde/0x1f1 0xffffc20000c36000-0xffffc20000c38000 8192 pci_iomap+0x8a/0xb4 phys=d8e00000 ioremap 0xffffc20000c38000-0xffffc20000c3a000 8192 usb_hcd_pci_probe+0x139/0x295 [usbcore] phys=d8e00000 ioremap 0xffffc20000c3a000-0xffffc20000c3e000 16384 sys_swapon+0x509/0xa15 pages=3 vmalloc 0xffffc20000c40000-0xffffc20000c61000 135168 e1000_probe+0x1c4/0xa32 phys=d8a20000 ioremap 0xffffc20000c61000-0xffffc20000c6a000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c6a000-0xffffc20000c73000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c73000-0xffffc20000c7c000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c7c000-0xffffc20000c7f000 12288 e1000e_setup_tx_resources+0x29/0xbe pages=2 vmalloc 0xffffc20000c80000-0xffffc20001481000 8392704 pci_mmcfg_arch_init+0x90/0x118 phys=e0000000 ioremap 0xffffc20001481000-0xffffc20001682000 2101248 alloc_large_system_hash+0x127/0x246 pages=512 vmalloc 0xffffc20001682000-0xffffc20001e83000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20001e83000-0xffffc20002204000 3674112 alloc_large_system_hash+0x127/0x246 pages=896 vmalloc vpages 0xffffc20002204000-0xffffc2000220d000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000220d000-0xffffc20002216000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002216000-0xffffc2000221f000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000221f000-0xffffc20002228000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002228000-0xffffc20002231000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002231000-0xffffc20002234000 12288 e1000e_setup_rx_resources+0x35/0x122 pages=2 vmalloc 0xffffc20002240000-0xffffc20002261000 135168 e1000_probe+0x1c4/0xa32 phys=d8a60000 ioremap 0xffffc20002261000-0xffffc2000270c000 4894720 sys_swapon+0x509/0xa15 pages=1194 vmalloc vpages 0xffffffffa0000000-0xffffffffa0022000 139264 module_alloc+0x4f/0x55 pages=33 vmalloc 0xffffffffa0022000-0xffffffffa0029000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc 0xffffffffa002b000-0xffffffffa0034000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa0034000-0xffffffffa003d000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa003d000-0xffffffffa0049000 49152 module_alloc+0x4f/0x55 pages=11 vmalloc 0xffffffffa0049000-0xffffffffa0050000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Lameter <clameter@sgi.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:12:42 +08:00
__builtin_return_address(0));
}
EXPORT_SYMBOL(__vmalloc_noprof);
/**
* vmalloc - allocate virtually contiguous memory
* @size: allocation size
*
* Allocate enough pages to cover @size from the page level
* allocator and map them into contiguous kernel virtual space.
*
* For tight control over page level allocator and protection flags
* use __vmalloc() instead.
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *vmalloc_noprof(unsigned long size)
{
return __vmalloc_node_noprof(size, 1, GFP_KERNEL, NUMA_NO_NODE,
mm: remove both instances of __vmalloc_node_flags The real version just had a few callers that can open code it and remove one layer of indirection. The nommu stub was public but only had a single caller, so remove it and avoid a CONFIG_MMU ifdef in vmalloc.h. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-24-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:49 +08:00
__builtin_return_address(0));
}
EXPORT_SYMBOL(vmalloc_noprof);
mm/vmalloc: add vmalloc_no_huge Patch series "mm: add vmalloc_no_huge and use it", v4. Add vmalloc_no_huge() and export it, so modules can allocate memory with small pages. Use the newly added vmalloc_no_huge() in KVM on s390 to get around a hardware limitation. This patch (of 2): Commit 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") added support for hugepage vmalloc mappings, it also added the flag VM_NO_HUGE_VMAP for __vmalloc_node_range to request the allocation to be performed with 0-order non-huge pages. This flag is not accessible when calling vmalloc, the only option is to call directly __vmalloc_node_range, which is not exported. This means that a module can't vmalloc memory with small pages. Case in point: KVM on s390x needs to vmalloc a large area, and it needs to be mapped with non-huge pages, because of a hardware limitation. This patch adds the function vmalloc_no_huge, which works like vmalloc, but it is guaranteed to always back the mapping using small pages. This new function is exported, therefore it is usable by modules. [akpm@linux-foundation.org: whitespace fixes, per Christoph] Link: https://lkml.kernel.org/r/20210614132357.10202-1-imbrenda@linux.ibm.com Link: https://lkml.kernel.org/r/20210614132357.10202-2-imbrenda@linux.ibm.com Fixes: 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-25 09:39:36 +08:00
/**
* vmalloc_huge - allocate virtually contiguous memory, allow huge pages
* @size: allocation size
* @gfp_mask: flags for the page level allocator
mm/vmalloc: add vmalloc_no_huge Patch series "mm: add vmalloc_no_huge and use it", v4. Add vmalloc_no_huge() and export it, so modules can allocate memory with small pages. Use the newly added vmalloc_no_huge() in KVM on s390 to get around a hardware limitation. This patch (of 2): Commit 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") added support for hugepage vmalloc mappings, it also added the flag VM_NO_HUGE_VMAP for __vmalloc_node_range to request the allocation to be performed with 0-order non-huge pages. This flag is not accessible when calling vmalloc, the only option is to call directly __vmalloc_node_range, which is not exported. This means that a module can't vmalloc memory with small pages. Case in point: KVM on s390x needs to vmalloc a large area, and it needs to be mapped with non-huge pages, because of a hardware limitation. This patch adds the function vmalloc_no_huge, which works like vmalloc, but it is guaranteed to always back the mapping using small pages. This new function is exported, therefore it is usable by modules. [akpm@linux-foundation.org: whitespace fixes, per Christoph] Link: https://lkml.kernel.org/r/20210614132357.10202-1-imbrenda@linux.ibm.com Link: https://lkml.kernel.org/r/20210614132357.10202-2-imbrenda@linux.ibm.com Fixes: 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-25 09:39:36 +08:00
*
* Allocate enough pages to cover @size from the page level
mm/vmalloc: add vmalloc_no_huge Patch series "mm: add vmalloc_no_huge and use it", v4. Add vmalloc_no_huge() and export it, so modules can allocate memory with small pages. Use the newly added vmalloc_no_huge() in KVM on s390 to get around a hardware limitation. This patch (of 2): Commit 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") added support for hugepage vmalloc mappings, it also added the flag VM_NO_HUGE_VMAP for __vmalloc_node_range to request the allocation to be performed with 0-order non-huge pages. This flag is not accessible when calling vmalloc, the only option is to call directly __vmalloc_node_range, which is not exported. This means that a module can't vmalloc memory with small pages. Case in point: KVM on s390x needs to vmalloc a large area, and it needs to be mapped with non-huge pages, because of a hardware limitation. This patch adds the function vmalloc_no_huge, which works like vmalloc, but it is guaranteed to always back the mapping using small pages. This new function is exported, therefore it is usable by modules. [akpm@linux-foundation.org: whitespace fixes, per Christoph] Link: https://lkml.kernel.org/r/20210614132357.10202-1-imbrenda@linux.ibm.com Link: https://lkml.kernel.org/r/20210614132357.10202-2-imbrenda@linux.ibm.com Fixes: 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-25 09:39:36 +08:00
* allocator and map them into contiguous kernel virtual space.
* If @size is greater than or equal to PMD_SIZE, allow using
* huge pages for the memory
mm/vmalloc: add vmalloc_no_huge Patch series "mm: add vmalloc_no_huge and use it", v4. Add vmalloc_no_huge() and export it, so modules can allocate memory with small pages. Use the newly added vmalloc_no_huge() in KVM on s390 to get around a hardware limitation. This patch (of 2): Commit 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") added support for hugepage vmalloc mappings, it also added the flag VM_NO_HUGE_VMAP for __vmalloc_node_range to request the allocation to be performed with 0-order non-huge pages. This flag is not accessible when calling vmalloc, the only option is to call directly __vmalloc_node_range, which is not exported. This means that a module can't vmalloc memory with small pages. Case in point: KVM on s390x needs to vmalloc a large area, and it needs to be mapped with non-huge pages, because of a hardware limitation. This patch adds the function vmalloc_no_huge, which works like vmalloc, but it is guaranteed to always back the mapping using small pages. This new function is exported, therefore it is usable by modules. [akpm@linux-foundation.org: whitespace fixes, per Christoph] Link: https://lkml.kernel.org/r/20210614132357.10202-1-imbrenda@linux.ibm.com Link: https://lkml.kernel.org/r/20210614132357.10202-2-imbrenda@linux.ibm.com Fixes: 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-25 09:39:36 +08:00
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *vmalloc_huge_noprof(unsigned long size, gfp_t gfp_mask)
mm/vmalloc: add vmalloc_no_huge Patch series "mm: add vmalloc_no_huge and use it", v4. Add vmalloc_no_huge() and export it, so modules can allocate memory with small pages. Use the newly added vmalloc_no_huge() in KVM on s390 to get around a hardware limitation. This patch (of 2): Commit 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") added support for hugepage vmalloc mappings, it also added the flag VM_NO_HUGE_VMAP for __vmalloc_node_range to request the allocation to be performed with 0-order non-huge pages. This flag is not accessible when calling vmalloc, the only option is to call directly __vmalloc_node_range, which is not exported. This means that a module can't vmalloc memory with small pages. Case in point: KVM on s390x needs to vmalloc a large area, and it needs to be mapped with non-huge pages, because of a hardware limitation. This patch adds the function vmalloc_no_huge, which works like vmalloc, but it is guaranteed to always back the mapping using small pages. This new function is exported, therefore it is usable by modules. [akpm@linux-foundation.org: whitespace fixes, per Christoph] Link: https://lkml.kernel.org/r/20210614132357.10202-1-imbrenda@linux.ibm.com Link: https://lkml.kernel.org/r/20210614132357.10202-2-imbrenda@linux.ibm.com Fixes: 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-25 09:39:36 +08:00
{
return __vmalloc_node_range_noprof(size, 1, VMALLOC_START, VMALLOC_END,
gfp_mask, PAGE_KERNEL, VM_ALLOW_HUGE_VMAP,
mm/vmalloc: add vmalloc_no_huge Patch series "mm: add vmalloc_no_huge and use it", v4. Add vmalloc_no_huge() and export it, so modules can allocate memory with small pages. Use the newly added vmalloc_no_huge() in KVM on s390 to get around a hardware limitation. This patch (of 2): Commit 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") added support for hugepage vmalloc mappings, it also added the flag VM_NO_HUGE_VMAP for __vmalloc_node_range to request the allocation to be performed with 0-order non-huge pages. This flag is not accessible when calling vmalloc, the only option is to call directly __vmalloc_node_range, which is not exported. This means that a module can't vmalloc memory with small pages. Case in point: KVM on s390x needs to vmalloc a large area, and it needs to be mapped with non-huge pages, because of a hardware limitation. This patch adds the function vmalloc_no_huge, which works like vmalloc, but it is guaranteed to always back the mapping using small pages. This new function is exported, therefore it is usable by modules. [akpm@linux-foundation.org: whitespace fixes, per Christoph] Link: https://lkml.kernel.org/r/20210614132357.10202-1-imbrenda@linux.ibm.com Link: https://lkml.kernel.org/r/20210614132357.10202-2-imbrenda@linux.ibm.com Fixes: 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-25 09:39:36 +08:00
NUMA_NO_NODE, __builtin_return_address(0));
}
EXPORT_SYMBOL_GPL(vmalloc_huge_noprof);
mm/vmalloc: add vmalloc_no_huge Patch series "mm: add vmalloc_no_huge and use it", v4. Add vmalloc_no_huge() and export it, so modules can allocate memory with small pages. Use the newly added vmalloc_no_huge() in KVM on s390 to get around a hardware limitation. This patch (of 2): Commit 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") added support for hugepage vmalloc mappings, it also added the flag VM_NO_HUGE_VMAP for __vmalloc_node_range to request the allocation to be performed with 0-order non-huge pages. This flag is not accessible when calling vmalloc, the only option is to call directly __vmalloc_node_range, which is not exported. This means that a module can't vmalloc memory with small pages. Case in point: KVM on s390x needs to vmalloc a large area, and it needs to be mapped with non-huge pages, because of a hardware limitation. This patch adds the function vmalloc_no_huge, which works like vmalloc, but it is guaranteed to always back the mapping using small pages. This new function is exported, therefore it is usable by modules. [akpm@linux-foundation.org: whitespace fixes, per Christoph] Link: https://lkml.kernel.org/r/20210614132357.10202-1-imbrenda@linux.ibm.com Link: https://lkml.kernel.org/r/20210614132357.10202-2-imbrenda@linux.ibm.com Fixes: 121e6f3258fe3 ("mm/vmalloc: hugepage vmalloc mappings") Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-06-25 09:39:36 +08:00
/**
* vzalloc - allocate virtually contiguous memory with zero fill
* @size: allocation size
*
* Allocate enough pages to cover @size from the page level
* allocator and map them into contiguous kernel virtual space.
* The memory allocated is set to zero.
*
* For tight control over page level allocator and protection flags
* use __vmalloc() instead.
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *vzalloc_noprof(unsigned long size)
{
return __vmalloc_node_noprof(size, 1, GFP_KERNEL | __GFP_ZERO, NUMA_NO_NODE,
mm: remove both instances of __vmalloc_node_flags The real version just had a few callers that can open code it and remove one layer of indirection. The nommu stub was public but only had a single caller, so remove it and avoid a CONFIG_MMU ifdef in vmalloc.h. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-24-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:49 +08:00
__builtin_return_address(0));
}
EXPORT_SYMBOL(vzalloc_noprof);
/**
* vmalloc_user - allocate zeroed virtually contiguous memory for userspace
* @size: allocation size
*
* The resulting memory area is zeroed so it can be mapped to userspace
* without leaking data.
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *vmalloc_user_noprof(unsigned long size)
{
return __vmalloc_node_range_noprof(size, SHMLBA, VMALLOC_START, VMALLOC_END,
GFP_KERNEL | __GFP_ZERO, PAGE_KERNEL,
VM_USERMAP, NUMA_NO_NODE,
__builtin_return_address(0));
}
EXPORT_SYMBOL(vmalloc_user_noprof);
/**
* vmalloc_node - allocate memory on a specific node
* @size: allocation size
* @node: numa node
*
* Allocate enough pages to cover @size from the page level
* allocator and map them into contiguous kernel virtual space.
*
* For tight control over page level allocator and protection flags
* use __vmalloc() instead.
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *vmalloc_node_noprof(unsigned long size, int node)
{
return __vmalloc_node_noprof(size, 1, GFP_KERNEL, node,
__builtin_return_address(0));
}
EXPORT_SYMBOL(vmalloc_node_noprof);
/**
* vzalloc_node - allocate memory on a specific node with zero fill
* @size: allocation size
* @node: numa node
*
* Allocate enough pages to cover @size from the page level
* allocator and map them into contiguous kernel virtual space.
* The memory allocated is set to zero.
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *vzalloc_node_noprof(unsigned long size, int node)
{
return __vmalloc_node_noprof(size, 1, GFP_KERNEL | __GFP_ZERO, node,
mm: remove both instances of __vmalloc_node_flags The real version just had a few callers that can open code it and remove one layer of indirection. The nommu stub was public but only had a single caller, so remove it and avoid a CONFIG_MMU ifdef in vmalloc.h. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-24-hch@lst.de Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-02 12:51:49 +08:00
__builtin_return_address(0));
}
EXPORT_SYMBOL(vzalloc_node_noprof);
#if defined(CONFIG_64BIT) && defined(CONFIG_ZONE_DMA32)
#define GFP_VMALLOC32 (GFP_DMA32 | GFP_KERNEL)
#elif defined(CONFIG_64BIT) && defined(CONFIG_ZONE_DMA)
#define GFP_VMALLOC32 (GFP_DMA | GFP_KERNEL)
#else
/*
* 64b systems should always have either DMA or DMA32 zones. For others
* GFP_DMA32 should do the right thing and use the normal zone.
*/
mm/mempool: minor coding style tweaks Various coding style tweaks to various files under mm/ [daizhiyuan@phytium.com.cn: mm/swapfile: minor coding style tweaks] Link: https://lkml.kernel.org/r/1614223624-16055-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/sparse: minor coding style tweaks] Link: https://lkml.kernel.org/r/1614227288-19363-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/vmscan: minor coding style tweaks] Link: https://lkml.kernel.org/r/1614227649-19853-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/compaction: minor coding style tweaks] Link: https://lkml.kernel.org/r/1614228218-20770-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/oom_kill: minor coding style tweaks] Link: https://lkml.kernel.org/r/1614228360-21168-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/shmem: minor coding style tweaks] Link: https://lkml.kernel.org/r/1614228504-21491-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/page_alloc: minor coding style tweaks] Link: https://lkml.kernel.org/r/1614228613-21754-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/filemap: minor coding style tweaks] Link: https://lkml.kernel.org/r/1614228936-22337-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/mlock: minor coding style tweaks] Link: https://lkml.kernel.org/r/1613956588-2453-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/frontswap: minor coding style tweaks] Link: https://lkml.kernel.org/r/1613962668-15045-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/vmalloc: minor coding style tweaks] Link: https://lkml.kernel.org/r/1613963379-15988-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/memory_hotplug: minor coding style tweaks] Link: https://lkml.kernel.org/r/1613971784-24878-1-git-send-email-daizhiyuan@phytium.com.cn [daizhiyuan@phytium.com.cn: mm/mempolicy: minor coding style tweaks] Link: https://lkml.kernel.org/r/1613972228-25501-1-git-send-email-daizhiyuan@phytium.com.cn Link: https://lkml.kernel.org/r/1614222374-13805-1-git-send-email-daizhiyuan@phytium.com.cn Signed-off-by: Zhiyuan Dai <daizhiyuan@phytium.com.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 09:40:12 +08:00
#define GFP_VMALLOC32 (GFP_DMA32 | GFP_KERNEL)
#endif
/**
* vmalloc_32 - allocate virtually contiguous memory (32bit addressable)
* @size: allocation size
*
* Allocate enough 32bit PA addressable pages to cover @size from the
* page level allocator and map them into contiguous kernel virtual space.
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *vmalloc_32_noprof(unsigned long size)
{
return __vmalloc_node_noprof(size, 1, GFP_VMALLOC32, NUMA_NO_NODE,
__builtin_return_address(0));
}
EXPORT_SYMBOL(vmalloc_32_noprof);
/**
* vmalloc_32_user - allocate zeroed virtually contiguous 32bit memory
* @size: allocation size
*
* The resulting memory area is 32bit addressable and zeroed so it can be
* mapped to userspace without leaking data.
*
* Return: pointer to the allocated memory or %NULL on error
*/
void *vmalloc_32_user_noprof(unsigned long size)
{
return __vmalloc_node_range_noprof(size, SHMLBA, VMALLOC_START, VMALLOC_END,
GFP_VMALLOC32 | __GFP_ZERO, PAGE_KERNEL,
VM_USERMAP, NUMA_NO_NODE,
__builtin_return_address(0));
}
EXPORT_SYMBOL(vmalloc_32_user_noprof);
/*
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
* Atomically zero bytes in the iterator.
*
* Returns the number of zeroed bytes.
*/
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
static size_t zero_iter(struct iov_iter *iter, size_t count)
{
size_t remains = count;
while (remains > 0) {
size_t num, copied;
num = min_t(size_t, remains, PAGE_SIZE);
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
copied = copy_page_to_iter_nofault(ZERO_PAGE(0), 0, num, iter);
remains -= copied;
if (copied < num)
break;
}
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
return count - remains;
}
/*
* small helper routine, copy contents to iter from addr.
* If the page is not present, fill zero.
*
* Returns the number of copied bytes.
*/
static size_t aligned_vread_iter(struct iov_iter *iter,
const char *addr, size_t count)
{
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
size_t remains = count;
struct page *page;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
while (remains > 0) {
unsigned long offset, length;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
size_t copied = 0;
offset = offset_in_page(addr);
length = PAGE_SIZE - offset;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
if (length > remains)
length = remains;
page = vmalloc_to_page(addr);
/*
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
* To do safe access to this _mapped_ area, we need lock. But
* adding lock here means that we need to add overhead of
* vmalloc()/vfree() calls for this _debug_ interface, rarely
* used. Instead of that, we'll use an local mapping via
* copy_page_to_iter_nofault() and accept a small overhead in
* this access function.
*/
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
if (page)
copied = copy_page_to_iter_nofault(page, offset,
length, iter);
else
copied = zero_iter(iter, length);
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
addr += copied;
remains -= copied;
if (copied != length)
break;
}
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
return count - remains;
}
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
/*
* Read from a vm_map_ram region of memory.
*
* Returns the number of copied bytes.
*/
static size_t vmap_ram_vread_iter(struct iov_iter *iter, const char *addr,
size_t count, unsigned long flags)
{
char *start;
struct vmap_block *vb;
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
struct xarray *xa;
unsigned long offset;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
unsigned int rs, re;
size_t remains, n;
/*
* If it's area created by vm_map_ram() interface directly, but
* not further subdividing and delegating management to vmap_block,
* handle it here.
*/
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
if (!(flags & VMAP_BLOCK))
return aligned_vread_iter(iter, addr, count);
remains = count;
/*
* Area is split into regions and tracked with vmap_block, read out
* each region and zero fill the hole between regions.
*/
xa = addr_to_vb_xa((unsigned long) addr);
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
vb = xa_load(xa, addr_to_vb_idx((unsigned long)addr));
if (!vb)
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
goto finished_zero;
spin_lock(&vb->lock);
if (bitmap_empty(vb->used_map, VMAP_BBMAP_BITS)) {
spin_unlock(&vb->lock);
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
goto finished_zero;
}
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
for_each_set_bitrange(rs, re, vb->used_map, VMAP_BBMAP_BITS) {
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
size_t copied;
if (remains == 0)
goto finished;
start = vmap_block_vaddr(vb->va->va_start, rs);
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
if (addr < start) {
size_t to_zero = min_t(size_t, start - addr, remains);
size_t zeroed = zero_iter(iter, to_zero);
addr += zeroed;
remains -= zeroed;
if (remains == 0 || zeroed != to_zero)
goto finished;
}
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
/*it could start reading from the middle of used region*/
offset = offset_in_page(addr);
n = ((re - rs + 1) << PAGE_SHIFT) - offset;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
if (n > remains)
n = remains;
copied = aligned_vread_iter(iter, start + offset, n);
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
addr += copied;
remains -= copied;
if (copied != n)
goto finished;
}
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
spin_unlock(&vb->lock);
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
finished_zero:
/* zero-fill the left dirty or free regions */
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
return count - remains + zero_iter(iter, remains);
finished:
/* We couldn't copy/zero everything */
spin_unlock(&vb->lock);
return count - remains;
}
/**
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
* vread_iter() - read vmalloc area in a safe way to an iterator.
* @iter: the iterator to which data should be written.
* @addr: vm address.
* @count: number of bytes to be read.
*
* This function checks that addr is a valid vmalloc'ed area, and
* copy data from that area to a given buffer. If the given memory range
* of [addr...addr+count) includes some valid address, data is copied to
* proper area of @buf. If there are memory holes, they'll be zero-filled.
* IOREMAP area is treated as memory hole and no copy is done.
*
* If [addr...addr+count) doesn't includes any intersects with alive
* vm_struct area, returns 0. @buf should be kernel's buffer.
*
* Note: In usual ops, vread() is never necessary because the caller
* should know vmalloc() area is valid and can use memcpy().
* This is for routines which have to access vmalloc area without
drivers/char: remove /dev/kmem for good Patch series "drivers/char: remove /dev/kmem for good". Exploring /dev/kmem and /dev/mem in the context of memory hot(un)plug and memory ballooning, I started questioning the existence of /dev/kmem. Comparing it with the /proc/kcore implementation, it does not seem to be able to deal with things like a) Pages unmapped from the direct mapping (e.g., to be used by secretmem) -> kern_addr_valid(). virt_addr_valid() is not sufficient. b) Special cases like gart aperture memory that is not to be touched -> mem_pfn_is_ram() Unless I am missing something, it's at least broken in some cases and might fault/crash the machine. Looks like its existence has been questioned before in 2005 and 2010 [1], after ~11 additional years, it might make sense to revive the discussion. CONFIG_DEVKMEM is only enabled in a single defconfig (on purpose or by mistake?). All distributions disable it: in Ubuntu it has been disabled for more than 10 years, in Debian since 2.6.31, in Fedora at least starting with FC3, in RHEL starting with RHEL4, in SUSE starting from 15sp2, and OpenSUSE has it disabled as well. 1) /dev/kmem was popular for rootkits [2] before it got disabled basically everywhere. Ubuntu documents [3] "There is no modern user of /dev/kmem any more beyond attackers using it to load kernel rootkits.". RHEL documents in a BZ [5] "it served no practical purpose other than to serve as a potential security problem or to enable binary module drivers to access structures/functions they shouldn't be touching" 2) /proc/kcore is a decent interface to have a controlled way to read kernel memory for debugging puposes. (will need some extensions to deal with memory offlining/unplug, memory ballooning, and poisoned pages, though) 3) It might be useful for corner case debugging [1]. KDB/KGDB might be a better fit, especially, to write random memory; harder to shoot yourself into the foot. 4) "Kernel Memory Editor" [4] hasn't seen any updates since 2000 and seems to be incompatible with 64bit [1]. For educational purposes, /proc/kcore might be used to monitor value updates -- or older kernels can be used. 5) It's broken on arm64, and therefore, completely disabled there. Looks like it's essentially unused and has been replaced by better suited interfaces for individual tasks (/proc/kcore, KDB/KGDB). Let's just remove it. [1] https://lwn.net/Articles/147901/ [2] https://www.linuxjournal.com/article/10505 [3] https://wiki.ubuntu.com/Security/Features#A.2Fdev.2Fkmem_disabled [4] https://sourceforge.net/projects/kme/ [5] https://bugzilla.redhat.com/show_bug.cgi?id=154796 Link: https://lkml.kernel.org/r/20210324102351.6932-1-david@redhat.com Link: https://lkml.kernel.org/r/20210324102351.6932-2-david@redhat.com Signed-off-by: David Hildenbrand <david@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Brian Cain <bcain@codeaurora.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Chris Zankel <chris@zankel.net> Cc: Corentin Labbe <clabbe@baylibre.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Cc: Greentime Hu <green.hu@gmail.com> Cc: Gregory Clement <gregory.clement@bootlin.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Helge Deller <deller@gmx.de> Cc: Hillf Danton <hdanton@sina.com> Cc: huang ying <huang.ying.caritas@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: James Troup <james.troup@canonical.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Jonas Bonn <jonas@southpole.se> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kairui Song <kasong@redhat.com> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Mike Rapoport <rppt@kernel.org> Cc: Mikulas Patocka <mpatocka@redhat.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Niklas Schnelle <schnelle@linux.ibm.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: openrisc@lists.librecores.org Cc: Palmer Dabbelt <palmerdabbelt@google.com> Cc: Paul Mackerras <paulus@samba.org> Cc: "Pavel Machek (CIP)" <pavel@denx.de> Cc: Pavel Machek <pavel@ucw.cz> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Pierre Morel <pmorel@linux.ibm.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Rich Felker <dalias@libc.org> Cc: Robert Richter <rric@kernel.org> Cc: Rob Herring <robh@kernel.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: sparclinux@vger.kernel.org Cc: Stafford Horne <shorne@gmail.com> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Theodore Dubois <tblodt@icloud.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: William Cohen <wcohen@redhat.com> Cc: Xiaoming Ni <nixiaoming@huawei.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-07 09:05:55 +08:00
* any information, as /proc/kcore.
*
* Return: number of bytes for which addr and buf should be increased
* (same number as @count) or %0 if [addr...addr+count) doesn't
* include any intersection with valid vmalloc area
*/
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
long vread_iter(struct iov_iter *iter, const char *addr, size_t count)
{
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn;
struct vmap_area *va;
struct vm_struct *vm;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
char *vaddr;
size_t n, size, flags, remains;
unsigned long next;
addr = kasan_reset_tag(addr);
/* Don't allow overflow */
if ((unsigned long) addr + count < count)
count = -(unsigned long) addr;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
remains = count;
vn = find_vmap_area_exceed_addr_lock((unsigned long) addr, &va);
if (!vn)
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
goto finished_zero;
/* no intersects with alive vmap_area */
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
if ((unsigned long)addr + remains <= va->va_start)
goto finished_zero;
do {
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
size_t copied;
if (remains == 0)
goto finished;
vm = va->vm;
flags = va->flags & VMAP_FLAGS_MASK;
/*
* VMAP_BLOCK indicates a sub-type of vm_map_ram area, need
* be set together with VMAP_RAM.
*/
WARN_ON(flags == VMAP_BLOCK);
if (!vm && !flags)
goto next_va;
if (vm && (vm->flags & VM_UNINITIALIZED))
goto next_va;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
/* Pair with smp_wmb() in clear_vm_uninitialized_flag() */
smp_rmb();
vaddr = (char *) va->va_start;
size = vm ? get_vm_area_size(vm) : va_size(va);
if (addr >= vaddr + size)
goto next_va;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
if (addr < vaddr) {
size_t to_zero = min_t(size_t, vaddr - addr, remains);
size_t zeroed = zero_iter(iter, to_zero);
addr += zeroed;
remains -= zeroed;
if (remains == 0 || zeroed != to_zero)
goto finished;
}
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
n = vaddr + size - addr;
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
if (n > remains)
n = remains;
if (flags & VMAP_RAM)
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
copied = vmap_ram_vread_iter(iter, addr, n, flags);
mm: Introduce VM_SPARSE kind and vm_area_[un]map_pages(). vmap/vmalloc APIs are used to map a set of pages into contiguous kernel virtual space. get_vm_area() with appropriate flag is used to request an area of kernel address range. It's used for vmalloc, vmap, ioremap, xen use cases. - vmalloc use case dominates the usage. Such vm areas have VM_ALLOC flag. - the areas created by vmap() function should be tagged with VM_MAP. - ioremap areas are tagged with VM_IOREMAP. BPF would like to extend the vmap API to implement a lazily-populated sparse, yet contiguous kernel virtual space. Introduce VM_SPARSE flag and vm_area_map_pages(area, start_addr, count, pages) API to map a set of pages within a given area. It has the same sanity checks as vmap() does. It also checks that get_vm_area() was created with VM_SPARSE flag which identifies such areas in /proc/vmallocinfo and returns zero pages on read through /proc/kcore. The next commits will introduce bpf_arena which is a sparsely populated shared memory region between bpf program and user space process. It will map privately-managed pages into a sparse vm area with the following steps: // request virtual memory region during bpf prog verification area = get_vm_area(area_size, VM_SPARSE); // on demand vm_area_map_pages(area, kaddr, kend, pages); vm_area_unmap_pages(area, kaddr, kend); // after bpf program is detached and unloaded free_vm_area(area); Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com> Link: https://lore.kernel.org/bpf/20240305030516.41519-3-alexei.starovoitov@gmail.com
2024-03-05 11:05:16 +08:00
else if (!(vm && (vm->flags & (VM_IOREMAP | VM_SPARSE))))
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
copied = aligned_vread_iter(iter, addr, n);
mm: Introduce VM_SPARSE kind and vm_area_[un]map_pages(). vmap/vmalloc APIs are used to map a set of pages into contiguous kernel virtual space. get_vm_area() with appropriate flag is used to request an area of kernel address range. It's used for vmalloc, vmap, ioremap, xen use cases. - vmalloc use case dominates the usage. Such vm areas have VM_ALLOC flag. - the areas created by vmap() function should be tagged with VM_MAP. - ioremap areas are tagged with VM_IOREMAP. BPF would like to extend the vmap API to implement a lazily-populated sparse, yet contiguous kernel virtual space. Introduce VM_SPARSE flag and vm_area_map_pages(area, start_addr, count, pages) API to map a set of pages within a given area. It has the same sanity checks as vmap() does. It also checks that get_vm_area() was created with VM_SPARSE flag which identifies such areas in /proc/vmallocinfo and returns zero pages on read through /proc/kcore. The next commits will introduce bpf_arena which is a sparsely populated shared memory region between bpf program and user space process. It will map privately-managed pages into a sparse vm area with the following steps: // request virtual memory region during bpf prog verification area = get_vm_area(area_size, VM_SPARSE); // on demand vm_area_map_pages(area, kaddr, kend, pages); vm_area_unmap_pages(area, kaddr, kend); // after bpf program is detached and unloaded free_vm_area(area); Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com> Link: https://lore.kernel.org/bpf/20240305030516.41519-3-alexei.starovoitov@gmail.com
2024-03-05 11:05:16 +08:00
else /* IOREMAP | SPARSE area is treated as memory hole */
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
copied = zero_iter(iter, n);
addr += copied;
remains -= copied;
if (copied != n)
goto finished;
next_va:
next = va->va_end;
spin_unlock(&vn->busy.lock);
} while ((vn = find_vmap_area_exceed_addr_lock(next, &va)));
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
finished_zero:
if (vn)
spin_unlock(&vn->busy.lock);
/* zero-fill memory holes */
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
return count - remains + zero_iter(iter, remains);
finished:
/* Nothing remains, or We couldn't copy/zero everything. */
if (vn)
spin_unlock(&vn->busy.lock);
mm: vmalloc: convert vread() to vread_iter() Having previously laid the foundation for converting vread() to an iterator function, pull the trigger and do so. This patch attempts to provide minimal refactoring and to reflect the existing logic as best we can, for example we continue to zero portions of memory not read, as before. Overall, there should be no functional difference other than a performance improvement in /proc/kcore access to vmalloc regions. Now we have eliminated the need for a bounce buffer in read_kcore_iter(), we dispense with it, and try to write to user memory optimistically but with faults disabled via copy_page_to_iter_nofault(). We already have preemption disabled by holding a spin lock. We continue faulting in until the operation is complete. Additionally, we must account for the fact that at any point a copy may fail (most likely due to a fault not being able to occur), we exit indicating fewer bytes retrieved than expected. [sfr@canb.auug.org.au: fix sparc64 warning] Link: https://lkml.kernel.org/r/20230320144721.663280c3@canb.auug.org.au [lstoakes@gmail.com: redo Stephen's sparc build fix] Link: https://lkml.kernel.org/r/8506cbc667c39205e65a323f750ff9c11a463798.1679566220.git.lstoakes@gmail.com [akpm@linux-foundation.org: unbreak uio.h includes] Link: https://lkml.kernel.org/r/941f88bc5ab928e6656e1e2593b91bf0f8c81e1b.1679511146.git.lstoakes@gmail.com Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: David Hildenbrand <david@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-23 02:57:04 +08:00
return count - remains;
}
/**
* remap_vmalloc_range_partial - map vmalloc pages to userspace
* @vma: vma to cover
* @uaddr: target user address to start at
* @kaddr: virtual address of vmalloc kernel memory
vmalloc: fix remap_vmalloc_range() bounds checks remap_vmalloc_range() has had various issues with the bounds checks it promises to perform ("This function checks that addr is a valid vmalloc'ed area, and that it is big enough to cover the vma") over time, e.g.: - not detecting pgoff<<PAGE_SHIFT overflow - not detecting (pgoff<<PAGE_SHIFT)+usize overflow - not checking whether addr and addr+(pgoff<<PAGE_SHIFT) are the same vmalloc allocation - comparing a potentially wildly out-of-bounds pointer with the end of the vmalloc region In particular, since commit fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"), unprivileged users can cause kernel null pointer dereferences by calling mmap() on a BPF map with a size that is bigger than the distance from the start of the BPF map to the end of the address space. This could theoretically be used as a kernel ASLR bypass, by using whether mmap() with a given offset oopses or returns an error code to perform a binary search over the possible address range. To allow remap_vmalloc_range_partial() to verify that addr and addr+(pgoff<<PAGE_SHIFT) are in the same vmalloc region, pass the offset to remap_vmalloc_range_partial() instead of adding it to the pointer in remap_vmalloc_range(). In remap_vmalloc_range_partial(), fix the check against get_vm_area_size() by using size comparisons instead of pointer comparisons, and add checks for pgoff. Fixes: 833423143c3a ("[PATCH] mm: introduce remap_vmalloc_range()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable@vger.kernel.org Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: Andrii Nakryiko <andriin@fb.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@chromium.org> Link: http://lkml.kernel.org/r/20200415222312.236431-1-jannh@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-21 09:14:11 +08:00
* @pgoff: offset from @kaddr to start at
* @size: size of map area
*
* Returns: 0 for success, -Exxx on failure
*
* This function checks that @kaddr is a valid vmalloc'ed area,
* and that it is big enough to cover the range starting at
* @uaddr in @vma. Will return failure if that criteria isn't
* met.
*
* Similar to remap_pfn_range() (see mm/memory.c)
*/
int remap_vmalloc_range_partial(struct vm_area_struct *vma, unsigned long uaddr,
vmalloc: fix remap_vmalloc_range() bounds checks remap_vmalloc_range() has had various issues with the bounds checks it promises to perform ("This function checks that addr is a valid vmalloc'ed area, and that it is big enough to cover the vma") over time, e.g.: - not detecting pgoff<<PAGE_SHIFT overflow - not detecting (pgoff<<PAGE_SHIFT)+usize overflow - not checking whether addr and addr+(pgoff<<PAGE_SHIFT) are the same vmalloc allocation - comparing a potentially wildly out-of-bounds pointer with the end of the vmalloc region In particular, since commit fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"), unprivileged users can cause kernel null pointer dereferences by calling mmap() on a BPF map with a size that is bigger than the distance from the start of the BPF map to the end of the address space. This could theoretically be used as a kernel ASLR bypass, by using whether mmap() with a given offset oopses or returns an error code to perform a binary search over the possible address range. To allow remap_vmalloc_range_partial() to verify that addr and addr+(pgoff<<PAGE_SHIFT) are in the same vmalloc region, pass the offset to remap_vmalloc_range_partial() instead of adding it to the pointer in remap_vmalloc_range(). In remap_vmalloc_range_partial(), fix the check against get_vm_area_size() by using size comparisons instead of pointer comparisons, and add checks for pgoff. Fixes: 833423143c3a ("[PATCH] mm: introduce remap_vmalloc_range()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable@vger.kernel.org Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: Andrii Nakryiko <andriin@fb.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@chromium.org> Link: http://lkml.kernel.org/r/20200415222312.236431-1-jannh@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-21 09:14:11 +08:00
void *kaddr, unsigned long pgoff,
unsigned long size)
{
struct vm_struct *area;
vmalloc: fix remap_vmalloc_range() bounds checks remap_vmalloc_range() has had various issues with the bounds checks it promises to perform ("This function checks that addr is a valid vmalloc'ed area, and that it is big enough to cover the vma") over time, e.g.: - not detecting pgoff<<PAGE_SHIFT overflow - not detecting (pgoff<<PAGE_SHIFT)+usize overflow - not checking whether addr and addr+(pgoff<<PAGE_SHIFT) are the same vmalloc allocation - comparing a potentially wildly out-of-bounds pointer with the end of the vmalloc region In particular, since commit fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"), unprivileged users can cause kernel null pointer dereferences by calling mmap() on a BPF map with a size that is bigger than the distance from the start of the BPF map to the end of the address space. This could theoretically be used as a kernel ASLR bypass, by using whether mmap() with a given offset oopses or returns an error code to perform a binary search over the possible address range. To allow remap_vmalloc_range_partial() to verify that addr and addr+(pgoff<<PAGE_SHIFT) are in the same vmalloc region, pass the offset to remap_vmalloc_range_partial() instead of adding it to the pointer in remap_vmalloc_range(). In remap_vmalloc_range_partial(), fix the check against get_vm_area_size() by using size comparisons instead of pointer comparisons, and add checks for pgoff. Fixes: 833423143c3a ("[PATCH] mm: introduce remap_vmalloc_range()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable@vger.kernel.org Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: Andrii Nakryiko <andriin@fb.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@chromium.org> Link: http://lkml.kernel.org/r/20200415222312.236431-1-jannh@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-21 09:14:11 +08:00
unsigned long off;
unsigned long end_index;
if (check_shl_overflow(pgoff, PAGE_SHIFT, &off))
return -EINVAL;
size = PAGE_ALIGN(size);
if (!PAGE_ALIGNED(uaddr) || !PAGE_ALIGNED(kaddr))
return -EINVAL;
area = find_vm_area(kaddr);
if (!area)
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
return -EINVAL;
if (!(area->flags & (VM_USERMAP | VM_DMA_COHERENT)))
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
return -EINVAL;
vmalloc: fix remap_vmalloc_range() bounds checks remap_vmalloc_range() has had various issues with the bounds checks it promises to perform ("This function checks that addr is a valid vmalloc'ed area, and that it is big enough to cover the vma") over time, e.g.: - not detecting pgoff<<PAGE_SHIFT overflow - not detecting (pgoff<<PAGE_SHIFT)+usize overflow - not checking whether addr and addr+(pgoff<<PAGE_SHIFT) are the same vmalloc allocation - comparing a potentially wildly out-of-bounds pointer with the end of the vmalloc region In particular, since commit fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"), unprivileged users can cause kernel null pointer dereferences by calling mmap() on a BPF map with a size that is bigger than the distance from the start of the BPF map to the end of the address space. This could theoretically be used as a kernel ASLR bypass, by using whether mmap() with a given offset oopses or returns an error code to perform a binary search over the possible address range. To allow remap_vmalloc_range_partial() to verify that addr and addr+(pgoff<<PAGE_SHIFT) are in the same vmalloc region, pass the offset to remap_vmalloc_range_partial() instead of adding it to the pointer in remap_vmalloc_range(). In remap_vmalloc_range_partial(), fix the check against get_vm_area_size() by using size comparisons instead of pointer comparisons, and add checks for pgoff. Fixes: 833423143c3a ("[PATCH] mm: introduce remap_vmalloc_range()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable@vger.kernel.org Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: Andrii Nakryiko <andriin@fb.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@chromium.org> Link: http://lkml.kernel.org/r/20200415222312.236431-1-jannh@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-21 09:14:11 +08:00
if (check_add_overflow(size, off, &end_index) ||
end_index > get_vm_area_size(area))
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
return -EINVAL;
vmalloc: fix remap_vmalloc_range() bounds checks remap_vmalloc_range() has had various issues with the bounds checks it promises to perform ("This function checks that addr is a valid vmalloc'ed area, and that it is big enough to cover the vma") over time, e.g.: - not detecting pgoff<<PAGE_SHIFT overflow - not detecting (pgoff<<PAGE_SHIFT)+usize overflow - not checking whether addr and addr+(pgoff<<PAGE_SHIFT) are the same vmalloc allocation - comparing a potentially wildly out-of-bounds pointer with the end of the vmalloc region In particular, since commit fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"), unprivileged users can cause kernel null pointer dereferences by calling mmap() on a BPF map with a size that is bigger than the distance from the start of the BPF map to the end of the address space. This could theoretically be used as a kernel ASLR bypass, by using whether mmap() with a given offset oopses or returns an error code to perform a binary search over the possible address range. To allow remap_vmalloc_range_partial() to verify that addr and addr+(pgoff<<PAGE_SHIFT) are in the same vmalloc region, pass the offset to remap_vmalloc_range_partial() instead of adding it to the pointer in remap_vmalloc_range(). In remap_vmalloc_range_partial(), fix the check against get_vm_area_size() by using size comparisons instead of pointer comparisons, and add checks for pgoff. Fixes: 833423143c3a ("[PATCH] mm: introduce remap_vmalloc_range()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable@vger.kernel.org Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: Andrii Nakryiko <andriin@fb.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@chromium.org> Link: http://lkml.kernel.org/r/20200415222312.236431-1-jannh@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-21 09:14:11 +08:00
kaddr += off;
do {
struct page *page = vmalloc_to_page(kaddr);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
int ret;
ret = vm_insert_page(vma, uaddr, page);
if (ret)
return ret;
uaddr += PAGE_SIZE;
kaddr += PAGE_SIZE;
size -= PAGE_SIZE;
} while (size > 0);
mm: replace vma->vm_flags direct modifications with modifier calls Replace direct modifications to vma->vm_flags with calls to modifier functions to be able to track flag changes and to keep vma locking correctness. [akpm@linux-foundation.org: fix drivers/misc/open-dice.c, per Hyeonggon Yoo] Link: https://lkml.kernel.org/r/20230126193752.297968-5-surenb@google.com Signed-off-by: Suren Baghdasaryan <surenb@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com> Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjun Roy <arjunroy@google.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: David Howells <dhowells@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: David Rientjes <rientjes@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Greg Thelen <gthelen@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Joel Fernandes <joelaf@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kent Overstreet <kent.overstreet@linux.dev> Cc: Laurent Dufour <ldufour@linux.ibm.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Minchan Kim <minchan@google.com> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Peter Oskolkov <posk@google.com> Cc: Peter Xu <peterx@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Punit Agrawal <punit.agrawal@bytedance.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Shakeel Butt <shakeelb@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Song Liu <songliubraving@fb.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-01-27 03:37:49 +08:00
vm_flags_set(vma, VM_DONTEXPAND | VM_DONTDUMP);
mm: rewrite vmap layer Rewrite the vmap allocator to use rbtrees and lazy tlb flushing, and provide a fast, scalable percpu frontend for small vmaps (requires a slightly different API, though). The biggest problem with vmap is actually vunmap. Presently this requires a global kernel TLB flush, which on most architectures is a broadcast IPI to all CPUs to flush the cache. This is all done under a global lock. As the number of CPUs increases, so will the number of vunmaps a scaled workload will want to perform, and so will the cost of a global TLB flush. This gives terrible quadratic scalability characteristics. Another problem is that the entire vmap subsystem works under a single lock. It is a rwlock, but it is actually taken for write in all the fast paths, and the read locking would likely never be run concurrently anyway, so it's just pointless. This is a rewrite of vmap subsystem to solve those problems. The existing vmalloc API is implemented on top of the rewritten subsystem. The TLB flushing problem is solved by using lazy TLB unmapping. vmap addresses do not have to be flushed immediately when they are vunmapped, because the kernel will not reuse them again (would be a use-after-free) until they are reallocated. So the addresses aren't allocated again until a subsequent TLB flush. A single TLB flush then can flush multiple vunmaps from each CPU. XEN and PAT and such do not like deferred TLB flushing because they can't always handle multiple aliasing virtual addresses to a physical address. They now call vm_unmap_aliases() in order to flush any deferred mappings. That call is very expensive (well, actually not a lot more expensive than a single vunmap under the old scheme), however it should be OK if not called too often. The virtual memory extent information is stored in an rbtree rather than a linked list to improve the algorithmic scalability. There is a per-CPU allocator for small vmaps, which amortizes or avoids global locking. To use the per-CPU interface, the vm_map_ram / vm_unmap_ram interfaces must be used in place of vmap and vunmap. Vmalloc does not use these interfaces at the moment, so it will not be quite so scalable (although it will use lazy TLB flushing). As a quick test of performance, I ran a test that loops in the kernel, linearly mapping then touching then unmapping 4 pages. Different numbers of tests were run in parallel on an 4 core, 2 socket opteron. Results are in nanoseconds per map+touch+unmap. threads vanilla vmap rewrite 1 14700 2900 2 33600 3000 4 49500 2800 8 70631 2900 So with a 8 cores, the rewritten version is already 25x faster. In a slightly more realistic test (although with an older and less scalable version of the patch), I ripped the not-very-good vunmap batching code out of XFS, and implemented the large buffer mapping with vm_map_ram and vm_unmap_ram... along with a couple of other tricks, I was able to speed up a large directory workload by 20x on a 64 CPU system. I believe vmap/vunmap is actually sped up a lot more than 20x on such a system, but I'm running into other locks now. vmap is pretty well blown off the profiles. Before: 1352059 total 0.1401 798784 _write_lock 8320.6667 <- vmlist_lock 529313 default_idle 1181.5022 15242 smp_call_function 15.8771 <- vmap tlb flushing 2472 __get_vm_area_node 1.9312 <- vmap 1762 remove_vm_area 4.5885 <- vunmap 316 map_vm_area 0.2297 <- vmap 312 kfree 0.1950 300 _spin_lock 3.1250 252 sn_send_IPI_phys 0.4375 <- tlb flushing 238 vmap 0.8264 <- vmap 216 find_lock_page 0.5192 196 find_next_bit 0.3603 136 sn2_send_IPI 0.2024 130 pio_phys_write_mmr 2.0312 118 unmap_kernel_range 0.1229 After: 78406 total 0.0081 40053 default_idle 89.4040 33576 ia64_spinlock_contention 349.7500 1650 _spin_lock 17.1875 319 __reg_op 0.5538 281 _atomic_dec_and_lock 1.0977 153 mutex_unlock 1.5938 123 iget_locked 0.1671 117 xfs_dir_lookup 0.1662 117 dput 0.1406 114 xfs_iget_core 0.0268 92 xfs_da_hashname 0.1917 75 d_alloc 0.0670 68 vmap_page_range 0.0462 <- vmap 58 kmem_cache_alloc 0.0604 57 memset 0.0540 52 rb_next 0.1625 50 __copy_user 0.0208 49 bitmap_find_free_region 0.2188 <- vmap 46 ia64_sn_udelay 0.1106 45 find_inode_fast 0.1406 42 memcmp 0.2188 42 finish_task_switch 0.1094 42 __d_lookup 0.0410 40 radix_tree_lookup_slot 0.1250 37 _spin_unlock_irqrestore 0.3854 36 xfs_bmapi 0.0050 36 kmem_cache_free 0.0256 35 xfs_vn_getattr 0.0322 34 radix_tree_lookup 0.1062 33 __link_path_walk 0.0035 31 xfs_da_do_buf 0.0091 30 _xfs_buf_find 0.0204 28 find_get_page 0.0875 27 xfs_iread 0.0241 27 __strncpy_from_user 0.2812 26 _xfs_buf_initialize 0.0406 24 _xfs_buf_lookup_pages 0.0179 24 vunmap_page_range 0.0250 <- vunmap 23 find_lock_page 0.0799 22 vm_map_ram 0.0087 <- vmap 20 kfree 0.0125 19 put_page 0.0330 18 __kmalloc 0.0176 17 xfs_da_node_lookup_int 0.0086 17 _read_lock 0.0885 17 page_waitqueue 0.0664 vmap has gone from being the top 5 on the profiles and flushing the crap out of all TLBs, to using less than 1% of kernel time. [akpm@linux-foundation.org: cleanups, section fix] [akpm@linux-foundation.org: fix build on alpha] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 11:27:03 +08:00
return 0;
}
/**
* remap_vmalloc_range - map vmalloc pages to userspace
* @vma: vma to cover (map full range of vma)
* @addr: vmalloc memory
* @pgoff: number of pages into addr before first page to map
*
* Returns: 0 for success, -Exxx on failure
*
* This function checks that addr is a valid vmalloc'ed area, and
* that it is big enough to cover the vma. Will return failure if
* that criteria isn't met.
*
* Similar to remap_pfn_range() (see mm/memory.c)
*/
int remap_vmalloc_range(struct vm_area_struct *vma, void *addr,
unsigned long pgoff)
{
return remap_vmalloc_range_partial(vma, vma->vm_start,
vmalloc: fix remap_vmalloc_range() bounds checks remap_vmalloc_range() has had various issues with the bounds checks it promises to perform ("This function checks that addr is a valid vmalloc'ed area, and that it is big enough to cover the vma") over time, e.g.: - not detecting pgoff<<PAGE_SHIFT overflow - not detecting (pgoff<<PAGE_SHIFT)+usize overflow - not checking whether addr and addr+(pgoff<<PAGE_SHIFT) are the same vmalloc allocation - comparing a potentially wildly out-of-bounds pointer with the end of the vmalloc region In particular, since commit fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"), unprivileged users can cause kernel null pointer dereferences by calling mmap() on a BPF map with a size that is bigger than the distance from the start of the BPF map to the end of the address space. This could theoretically be used as a kernel ASLR bypass, by using whether mmap() with a given offset oopses or returns an error code to perform a binary search over the possible address range. To allow remap_vmalloc_range_partial() to verify that addr and addr+(pgoff<<PAGE_SHIFT) are in the same vmalloc region, pass the offset to remap_vmalloc_range_partial() instead of adding it to the pointer in remap_vmalloc_range(). In remap_vmalloc_range_partial(), fix the check against get_vm_area_size() by using size comparisons instead of pointer comparisons, and add checks for pgoff. Fixes: 833423143c3a ("[PATCH] mm: introduce remap_vmalloc_range()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable@vger.kernel.org Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: Andrii Nakryiko <andriin@fb.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@chromium.org> Link: http://lkml.kernel.org/r/20200415222312.236431-1-jannh@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-21 09:14:11 +08:00
addr, pgoff,
vma->vm_end - vma->vm_start);
}
EXPORT_SYMBOL(remap_vmalloc_range);
void free_vm_area(struct vm_struct *area)
{
struct vm_struct *ret;
ret = remove_vm_area(area->addr);
BUG_ON(ret != area);
kfree(area);
}
EXPORT_SYMBOL_GPL(free_vm_area);
2008-04-28 17:12:40 +08:00
#ifdef CONFIG_SMP
static struct vmap_area *node_to_va(struct rb_node *n)
{
return rb_entry_safe(n, struct vmap_area, rb_node);
}
/**
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* pvm_find_va_enclose_addr - find the vmap_area @addr belongs to
* @addr: target address
*
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* Returns: vmap_area if it is found. If there is no such area
* the first highest(reverse order) vmap_area is returned
* i.e. va->va_start < addr && va->va_end < addr or NULL
* if there are no any areas before @addr.
*/
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
static struct vmap_area *
pvm_find_va_enclose_addr(unsigned long addr)
{
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
struct vmap_area *va, *tmp;
struct rb_node *n;
n = free_vmap_area_root.rb_node;
va = NULL;
while (n) {
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
tmp = rb_entry(n, struct vmap_area, rb_node);
if (tmp->va_start <= addr) {
va = tmp;
if (tmp->va_end >= addr)
break;
n = n->rb_right;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
} else {
n = n->rb_left;
}
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
return va;
}
/**
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* pvm_determine_end_from_reverse - find the highest aligned address
* of free block below VMALLOC_END
* @va:
* in - the VA we start the search(reverse order);
* out - the VA with the highest aligned end address.
* @align: alignment for required highest address
*
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* Returns: determined end address within vmap_area
*/
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
static unsigned long
pvm_determine_end_from_reverse(struct vmap_area **va, unsigned long align)
{
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
unsigned long vmalloc_end = VMALLOC_END & ~(align - 1);
unsigned long addr;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (likely(*va)) {
list_for_each_entry_from_reverse((*va),
&free_vmap_area_list, list) {
addr = min((*va)->va_end & ~(align - 1), vmalloc_end);
if ((*va)->va_start < addr)
return addr;
}
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
return 0;
}
/**
* pcpu_get_vm_areas - allocate vmalloc areas for percpu allocator
* @offsets: array containing offset of each area
* @sizes: array containing size of each area
* @nr_vms: the number of areas to allocate
* @align: alignment, all entries in @offsets and @sizes must be aligned to this
*
* Returns: kmalloc'd vm_struct pointer array pointing to allocated
* vm_structs on success, %NULL on failure
*
* Percpu allocator wants to use congruent vm areas so that it can
* maintain the offsets among percpu areas. This function allocates
* congruent vmalloc areas for it with GFP_KERNEL. These areas tend to
* be scattered pretty far, distance between two areas easily going up
* to gigabytes. To avoid interacting with regular vmallocs, these
* areas are allocated from top.
*
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* Despite its complicated look, this allocator is rather simple. It
* does everything top-down and scans free blocks from the end looking
* for matching base. While scanning, if any of the areas do not fit the
* base address is pulled down to fit the area. Scanning is repeated till
* all the areas fit and then all necessary data structures are inserted
* and the result is returned.
*/
struct vm_struct **pcpu_get_vm_areas(const unsigned long *offsets,
const size_t *sizes, int nr_vms,
size_t align)
{
const unsigned long vmalloc_start = ALIGN(VMALLOC_START, align);
const unsigned long vmalloc_end = VMALLOC_END & ~(align - 1);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
struct vmap_area **vas, *va;
struct vm_struct **vms;
int area, area2, last_area, term_area;
unsigned long base, start, size, end, last_end, orig_start, orig_end;
bool purged = false;
/* verify parameters and allocate data structures */
BUG_ON(offset_in_page(align) || !is_power_of_2(align));
for (last_area = 0, area = 0; area < nr_vms; area++) {
start = offsets[area];
end = start + sizes[area];
/* is everything aligned properly? */
BUG_ON(!IS_ALIGNED(offsets[area], align));
BUG_ON(!IS_ALIGNED(sizes[area], align));
/* detect the area with the highest address */
if (start > offsets[last_area])
last_area = area;
for (area2 = area + 1; area2 < nr_vms; area2++) {
unsigned long start2 = offsets[area2];
unsigned long end2 = start2 + sizes[area2];
BUG_ON(start2 < end && start < end2);
}
}
last_end = offsets[last_area] + sizes[last_area];
if (vmalloc_end - vmalloc_start < last_end) {
WARN_ON(true);
return NULL;
}
vms = kcalloc(nr_vms, sizeof(vms[0]), GFP_KERNEL);
vas = kcalloc(nr_vms, sizeof(vas[0]), GFP_KERNEL);
if (!vas || !vms)
goto err_free2;
for (area = 0; area < nr_vms; area++) {
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
vas[area] = kmem_cache_zalloc(vmap_area_cachep, GFP_KERNEL);
vms[area] = kzalloc(sizeof(struct vm_struct), GFP_KERNEL);
if (!vas[area] || !vms[area])
goto err_free;
}
retry:
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
spin_lock(&free_vmap_area_lock);
/* start scanning - we scan from the top, begin with the last area */
area = term_area = last_area;
start = offsets[area];
end = start + sizes[area];
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
va = pvm_find_va_enclose_addr(vmalloc_end);
base = pvm_determine_end_from_reverse(&va, align) - end;
while (true) {
/*
* base might have underflowed, add last_end before
* comparing.
*/
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (base + last_end < vmalloc_start + last_end)
goto overflow;
/*
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* Fitting base has not been found.
*/
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (va == NULL)
goto overflow;
mm/vmalloc.c: fix percpu free VM area search criteria Recent changes to the vmalloc code by commit 68ad4a330433 ("mm/vmalloc.c: keep track of free blocks for vmap allocation") can cause spurious percpu allocation failures. These, in turn, can result in panic()s in the slub code. One such possible panic was reported by Dave Hansen in following link https://lkml.org/lkml/2019/6/19/939. Another related panic observed is, RIP: 0033:0x7f46f7441b9b Call Trace: dump_stack+0x61/0x80 pcpu_alloc.cold.30+0x22/0x4f mem_cgroup_css_alloc+0x110/0x650 cgroup_apply_control_enable+0x133/0x330 cgroup_mkdir+0x41b/0x500 kernfs_iop_mkdir+0x5a/0x90 vfs_mkdir+0x102/0x1b0 do_mkdirat+0x7d/0xf0 do_syscall_64+0x5b/0x180 entry_SYSCALL_64_after_hwframe+0x44/0xa9 VMALLOC memory manager divides the entire VMALLOC space (VMALLOC_START to VMALLOC_END) into multiple VM areas (struct vm_areas), and it mainly uses two lists (vmap_area_list & free_vmap_area_list) to track the used and free VM areas in VMALLOC space. And pcpu_get_vm_areas(offsets[], sizes[], nr_vms, align) function is used for allocating congruent VM areas for percpu memory allocator. In order to not conflict with VMALLOC users, pcpu_get_vm_areas allocates VM areas near the end of the VMALLOC space. So the search for free vm_area for the given requirement starts near VMALLOC_END and moves upwards towards VMALLOC_START. Prior to commit 68ad4a330433, the search for free vm_area in pcpu_get_vm_areas() involves following two main steps. Step 1: Find a aligned "base" adress near VMALLOC_END. va = free vm area near VMALLOC_END Step 2: Loop through number of requested vm_areas and check, Step 2.1: if (base < VMALLOC_START) 1. fail with error Step 2.2: // end is offsets[area] + sizes[area] if (base + end > va->vm_end) 1. Move the base downwards and repeat Step 2 Step 2.3: if (base + start < va->vm_start) 1. Move to previous free vm_area node, find aligned base address and repeat Step 2 But Commit 68ad4a330433 removed Step 2.2 and modified Step 2.3 as below: Step 2.3: if (base + start < va->vm_start || base + end > va->vm_end) 1. Move to previous free vm_area node, find aligned base address and repeat Step 2 Above change is the root cause of spurious percpu memory allocation failures. For example, consider a case where a relatively large vm_area (~ 30 TB) was ignored in free vm_area search because it did not pass the base + end < vm->vm_end boundary check. Ignoring such large free vm_area's would lead to not finding free vm_area within boundary of VMALLOC_start to VMALLOC_END which in turn leads to allocation failures. So modify the search algorithm to include Step 2.2. Link: http://lkml.kernel.org/r/20190729232139.91131-1-sathyanarayanan.kuppuswamy@linux.intel.com Fixes: 68ad4a330433 ("mm/vmalloc.c: keep track of free blocks for vmap allocation") Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reported-by: Dave Hansen <dave.hansen@intel.com> Acked-by: Dennis Zhou <dennis@kernel.org> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: sathyanarayanan kuppuswamy <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-08-14 06:37:31 +08:00
/*
* If required width exceeds current VA block, move
mm/vmalloc.c: fix percpu free VM area search criteria Recent changes to the vmalloc code by commit 68ad4a330433 ("mm/vmalloc.c: keep track of free blocks for vmap allocation") can cause spurious percpu allocation failures. These, in turn, can result in panic()s in the slub code. One such possible panic was reported by Dave Hansen in following link https://lkml.org/lkml/2019/6/19/939. Another related panic observed is, RIP: 0033:0x7f46f7441b9b Call Trace: dump_stack+0x61/0x80 pcpu_alloc.cold.30+0x22/0x4f mem_cgroup_css_alloc+0x110/0x650 cgroup_apply_control_enable+0x133/0x330 cgroup_mkdir+0x41b/0x500 kernfs_iop_mkdir+0x5a/0x90 vfs_mkdir+0x102/0x1b0 do_mkdirat+0x7d/0xf0 do_syscall_64+0x5b/0x180 entry_SYSCALL_64_after_hwframe+0x44/0xa9 VMALLOC memory manager divides the entire VMALLOC space (VMALLOC_START to VMALLOC_END) into multiple VM areas (struct vm_areas), and it mainly uses two lists (vmap_area_list & free_vmap_area_list) to track the used and free VM areas in VMALLOC space. And pcpu_get_vm_areas(offsets[], sizes[], nr_vms, align) function is used for allocating congruent VM areas for percpu memory allocator. In order to not conflict with VMALLOC users, pcpu_get_vm_areas allocates VM areas near the end of the VMALLOC space. So the search for free vm_area for the given requirement starts near VMALLOC_END and moves upwards towards VMALLOC_START. Prior to commit 68ad4a330433, the search for free vm_area in pcpu_get_vm_areas() involves following two main steps. Step 1: Find a aligned "base" adress near VMALLOC_END. va = free vm area near VMALLOC_END Step 2: Loop through number of requested vm_areas and check, Step 2.1: if (base < VMALLOC_START) 1. fail with error Step 2.2: // end is offsets[area] + sizes[area] if (base + end > va->vm_end) 1. Move the base downwards and repeat Step 2 Step 2.3: if (base + start < va->vm_start) 1. Move to previous free vm_area node, find aligned base address and repeat Step 2 But Commit 68ad4a330433 removed Step 2.2 and modified Step 2.3 as below: Step 2.3: if (base + start < va->vm_start || base + end > va->vm_end) 1. Move to previous free vm_area node, find aligned base address and repeat Step 2 Above change is the root cause of spurious percpu memory allocation failures. For example, consider a case where a relatively large vm_area (~ 30 TB) was ignored in free vm_area search because it did not pass the base + end < vm->vm_end boundary check. Ignoring such large free vm_area's would lead to not finding free vm_area within boundary of VMALLOC_start to VMALLOC_END which in turn leads to allocation failures. So modify the search algorithm to include Step 2.2. Link: http://lkml.kernel.org/r/20190729232139.91131-1-sathyanarayanan.kuppuswamy@linux.intel.com Fixes: 68ad4a330433 ("mm/vmalloc.c: keep track of free blocks for vmap allocation") Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reported-by: Dave Hansen <dave.hansen@intel.com> Acked-by: Dennis Zhou <dennis@kernel.org> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: sathyanarayanan kuppuswamy <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-08-14 06:37:31 +08:00
* base downwards and then recheck.
*/
if (base + end > va->va_end) {
base = pvm_determine_end_from_reverse(&va, align) - end;
term_area = area;
continue;
}
/*
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
* If this VA does not fit, move base downwards and recheck.
*/
mm/vmalloc.c: fix percpu free VM area search criteria Recent changes to the vmalloc code by commit 68ad4a330433 ("mm/vmalloc.c: keep track of free blocks for vmap allocation") can cause spurious percpu allocation failures. These, in turn, can result in panic()s in the slub code. One such possible panic was reported by Dave Hansen in following link https://lkml.org/lkml/2019/6/19/939. Another related panic observed is, RIP: 0033:0x7f46f7441b9b Call Trace: dump_stack+0x61/0x80 pcpu_alloc.cold.30+0x22/0x4f mem_cgroup_css_alloc+0x110/0x650 cgroup_apply_control_enable+0x133/0x330 cgroup_mkdir+0x41b/0x500 kernfs_iop_mkdir+0x5a/0x90 vfs_mkdir+0x102/0x1b0 do_mkdirat+0x7d/0xf0 do_syscall_64+0x5b/0x180 entry_SYSCALL_64_after_hwframe+0x44/0xa9 VMALLOC memory manager divides the entire VMALLOC space (VMALLOC_START to VMALLOC_END) into multiple VM areas (struct vm_areas), and it mainly uses two lists (vmap_area_list & free_vmap_area_list) to track the used and free VM areas in VMALLOC space. And pcpu_get_vm_areas(offsets[], sizes[], nr_vms, align) function is used for allocating congruent VM areas for percpu memory allocator. In order to not conflict with VMALLOC users, pcpu_get_vm_areas allocates VM areas near the end of the VMALLOC space. So the search for free vm_area for the given requirement starts near VMALLOC_END and moves upwards towards VMALLOC_START. Prior to commit 68ad4a330433, the search for free vm_area in pcpu_get_vm_areas() involves following two main steps. Step 1: Find a aligned "base" adress near VMALLOC_END. va = free vm area near VMALLOC_END Step 2: Loop through number of requested vm_areas and check, Step 2.1: if (base < VMALLOC_START) 1. fail with error Step 2.2: // end is offsets[area] + sizes[area] if (base + end > va->vm_end) 1. Move the base downwards and repeat Step 2 Step 2.3: if (base + start < va->vm_start) 1. Move to previous free vm_area node, find aligned base address and repeat Step 2 But Commit 68ad4a330433 removed Step 2.2 and modified Step 2.3 as below: Step 2.3: if (base + start < va->vm_start || base + end > va->vm_end) 1. Move to previous free vm_area node, find aligned base address and repeat Step 2 Above change is the root cause of spurious percpu memory allocation failures. For example, consider a case where a relatively large vm_area (~ 30 TB) was ignored in free vm_area search because it did not pass the base + end < vm->vm_end boundary check. Ignoring such large free vm_area's would lead to not finding free vm_area within boundary of VMALLOC_start to VMALLOC_END which in turn leads to allocation failures. So modify the search algorithm to include Step 2.2. Link: http://lkml.kernel.org/r/20190729232139.91131-1-sathyanarayanan.kuppuswamy@linux.intel.com Fixes: 68ad4a330433 ("mm/vmalloc.c: keep track of free blocks for vmap allocation") Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reported-by: Dave Hansen <dave.hansen@intel.com> Acked-by: Dennis Zhou <dennis@kernel.org> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: sathyanarayanan kuppuswamy <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-08-14 06:37:31 +08:00
if (base + start < va->va_start) {
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
va = node_to_va(rb_prev(&va->rb_node));
base = pvm_determine_end_from_reverse(&va, align) - end;
term_area = area;
continue;
}
/*
* This area fits, move on to the previous one. If
* the previous one is the terminal one, we're done.
*/
area = (area + nr_vms - 1) % nr_vms;
if (area == term_area)
break;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
start = offsets[area];
end = start + sizes[area];
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
va = pvm_find_va_enclose_addr(base + end);
}
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/* we've found a fitting base, insert all va's */
for (area = 0; area < nr_vms; area++) {
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
int ret;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
start = base + offsets[area];
size = sizes[area];
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
va = pvm_find_va_enclose_addr(start);
if (WARN_ON_ONCE(va == NULL))
/* It is a BUG(), but trigger recovery instead. */
goto recovery;
ret = va_clip(&free_vmap_area_root,
&free_vmap_area_list, va, start, size);
if (WARN_ON_ONCE(unlikely(ret)))
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
/* It is a BUG(), but trigger recovery instead. */
goto recovery;
/* Allocated area. */
va = vas[area];
va->va_start = start;
va->va_end = start + size;
}
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
spin_unlock(&free_vmap_area_lock);
/* populate the kasan shadow space */
for (area = 0; area < nr_vms; area++) {
if (kasan_populate_vmalloc(vas[area]->va_start, sizes[area]))
goto err_free_shadow;
}
/* insert all vm's */
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
for (area = 0; area < nr_vms; area++) {
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn = addr_to_node(vas[area]->va_start);
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
spin_lock(&vn->busy.lock);
insert_vmap_area(vas[area], &vn->busy.root, &vn->busy.head);
mm/vmalloc: eliminated the lock contention from twice to once When allocating a new memory area where the mapping address range is known, it is observed that the vmap_node->busy.lock is acquired twice. The first acquisition occurs in the alloc_vmap_area() function when inserting the vm area into the vm mapping red-black tree. The second acquisition occurs in the setup_vmalloc_vm() function when updating the properties of the vm, such as flags and address, etc. Combine these two operations together in alloc_vmap_area(), which improves scalability when the vmap_node->busy.lock is contended. By doing so, the need to acquire the lock twice can also be eliminated to once. With the above change, tested on intel sapphire rapids platform(224 vcpu), a 4% performance improvement is gained on stress-ng/pthread(https://github.com/ColinIanKing/stress-ng), which is the stress test of thread creations. Link: https://lkml.kernel.org/r/20240307021440.64967-1-rulin.huang@intel.com Co-developed-by: "Chen, Tim C" <tim.c.chen@intel.com> Signed-off-by: "Chen, Tim C" <tim.c.chen@intel.com> Co-developed-by: "King, Colin" <colin.king@intel.com> Signed-off-by: "King, Colin" <colin.king@intel.com> Signed-off-by: rulinhuang <rulin.huang@intel.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Wangyang Guo <wangyang.guo@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-07 10:14:40 +08:00
setup_vmalloc_vm(vms[area], vas[area], VM_ALLOC,
pcpu_get_vm_areas);
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
spin_unlock(&vn->busy.lock);
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
}
/*
* Mark allocated areas as accessible. Do it now as a best-effort
* approach, as they can be mapped outside of vmalloc code.
kasan, vmalloc: add vmalloc tagging for HW_TAGS Add vmalloc tagging support to HW_TAGS KASAN. The key difference between HW_TAGS and the other two KASAN modes when it comes to vmalloc: HW_TAGS KASAN can only assign tags to physical memory. The other two modes have shadow memory covering every mapped virtual memory region. Make __kasan_unpoison_vmalloc() for HW_TAGS KASAN: - Skip non-VM_ALLOC mappings as HW_TAGS KASAN can only tag a single mapping of normal physical memory; see the comment in the function. - Generate a random tag, tag the returned pointer and the allocation, and initialize the allocation at the same time. - Propagate the tag into the page stucts to allow accesses through page_address(vmalloc_to_page()). The rest of vmalloc-related KASAN hooks are not needed: - The shadow-related ones are fully skipped. - __kasan_poison_vmalloc() is kept as a no-op with a comment. Poisoning and zeroing of physical pages that are backing vmalloc() allocations are skipped via __GFP_SKIP_KASAN_UNPOISON and __GFP_SKIP_ZERO: __kasan_unpoison_vmalloc() does that instead. Enabling CONFIG_KASAN_VMALLOC with HW_TAGS is not yet allowed. Link: https://lkml.kernel.org/r/d19b2e9e59a9abc59d05b72dea8429dcaea739c6.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:32 +08:00
* With hardware tag-based KASAN, marking is skipped for
* non-VM_ALLOC mappings, see __kasan_unpoison_vmalloc().
*/
2022-03-25 09:11:13 +08:00
for (area = 0; area < nr_vms; area++)
vms[area]->addr = kasan_unpoison_vmalloc(vms[area]->addr,
kasan, vmalloc: only tag normal vmalloc allocations The kernel can use to allocate executable memory. The only supported way to do that is via __vmalloc_node_range() with the executable bit set in the prot argument. (vmap() resets the bit via pgprot_nx()). Once tag-based KASAN modes start tagging vmalloc allocations, executing code from such allocations will lead to the PC register getting a tag, which is not tolerated by the kernel. Only tag the allocations for normal kernel pages. [andreyknvl@google.com: pass KASAN_VMALLOC_PROT_NORMAL to kasan_unpoison_vmalloc()] Link: https://lkml.kernel.org/r/9230ca3d3e40ffca041c133a524191fd71969a8d.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: support tagged vmalloc mappings] Link: https://lkml.kernel.org/r/2f6605e3a358cf64d73a05710cb3da356886ad29.1646233925.git.andreyknvl@google.com [andreyknvl@google.com: don't unintentionally disabled poisoning] Link: https://lkml.kernel.org/r/de4587d6a719232e83c760113e46ed2d4d8da61e.1646757322.git.andreyknvl@google.com Link: https://lkml.kernel.org/r/fbfd9939a4dc375923c9a5c6b9e7ab05c26b8c6b.1643047180.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Marco Elver <elver@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-03-25 09:11:35 +08:00
vms[area]->size, KASAN_VMALLOC_PROT_NORMAL);
2022-03-25 09:11:13 +08:00
kfree(vas);
return vms;
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
recovery:
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
/*
* Remove previously allocated areas. There is no
* need in removing these areas from the busy tree,
* because they are inserted only on the final step
* and when pcpu_get_vm_areas() is success.
*/
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
while (area--) {
orig_start = vas[area]->va_start;
orig_end = vas[area]->va_end;
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
va = merge_or_add_vmap_area_augment(vas[area], &free_vmap_area_root,
&free_vmap_area_list);
if (va)
kasan_release_vmalloc(orig_start, orig_end,
va->va_start, va->va_end);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
vas[area] = NULL;
}
overflow:
mm/vmalloc: rework vmap_area_lock With the new allocation approach introduced in the 5.2 kernel, it becomes possible to get rid of one global spinlock. By doing that we can further improve the KVA from the performance point of view. Basically we can have two independent locks, one for allocation part and another one for deallocation, because of two different entities: "free data structures" and "busy data structures". As a result, allocation/deallocation operations can still interfere between each other in case of running simultaneously on different CPUs, it means there is still dependency, but with two locks it becomes lower. Summarizing: - it reduces the high lock contention - it allows to perform operations on "free" and "busy" trees in parallel on different CPUs. Please note it does not solve scalability issue. Test results: In order to evaluate this patch, we can run "vmalloc test driver" to see how many CPU cycles it takes to complete all test cases running sequentially. All online CPUs run it so it will cause a high lock contention. HiKey 960, ARM64, 8xCPUs, big.LITTLE: <snip> sudo ./test_vmalloc.sh sequential_test_order=1 <snip> <default> [ 390.950557] All test took CPU0=457126382 cycles [ 391.046690] All test took CPU1=454763452 cycles [ 391.128586] All test took CPU2=454539334 cycles [ 391.222669] All test took CPU3=455649517 cycles [ 391.313946] All test took CPU4=388272196 cycles [ 391.410425] All test took CPU5=384036264 cycles [ 391.492219] All test took CPU6=387432964 cycles [ 391.578433] All test took CPU7=387201996 cycles <default> <patched> [ 304.721224] All test took CPU0=391521310 cycles [ 304.821219] All test took CPU1=393533002 cycles [ 304.917120] All test took CPU2=392243032 cycles [ 305.008986] All test took CPU3=392353853 cycles [ 305.108944] All test took CPU4=297630721 cycles [ 305.196406] All test took CPU5=297548736 cycles [ 305.288602] All test took CPU6=297092392 cycles [ 305.381088] All test took CPU7=297293597 cycles <patched> ~14%-23% patched variant is better. Link: http://lkml.kernel.org/r/20191022155800.20468-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-01 09:54:47 +08:00
spin_unlock(&free_vmap_area_lock);
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (!purged) {
mm/vmalloc: dont purge usable blocks unnecessarily Purging fragmented blocks is done unconditionally in several contexts: 1) From drain_vmap_area_work(), when the number of lazy to be freed vmap_areas reached the threshold 2) Reclaiming vmalloc address space from pcpu_get_vm_areas() 3) _vm_unmap_aliases() #1 There is no reason to zap fragmented vmap blocks unconditionally, simply because reclaiming all lazy areas drains at least 32MB * fls(num_online_cpus()) per invocation which is plenty. #2 Reclaiming when running out of space or due to memory pressure makes a lot of sense #3 _unmap_aliases() requires to touch everything because the caller has no clue which vmap_area used a particular page last and the vmap_area lost that information too. Except for the vfree + VM_FLUSH_RESET_PERMS case, which removes the vmap area first and then cares about the flush. That in turn requires a full walk of _all_ vmap areas including the one which was just added to the purge list. But as this has to be flushed anyway this is an opportunity to combine outstanding TLB flushes and do the housekeeping of purging freed areas, but like #1 there is no real good reason to zap usable vmap blocks unconditionally. Add a @force_purge argument to the newly split out block purge function and if not true only purge fragmented blocks which have less than 1/4 of their capacity left. Rename purge_vmap_area_lazy() to reclaim_and_purge_vmap_areas() to make it clear what the function does. [lstoakes@gmail.com: correct VMAP_PURGE_THRESHOLD check] Link: https://lkml.kernel.org/r/3e92ef61-b910-4576-88e7-cf43211fd4e7@lucifer.local Link: https://lkml.kernel.org/r/20230525124504.864005691@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-05-25 20:57:09 +08:00
reclaim_and_purge_vmap_areas();
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
purged = true;
/* Before "retry", check if we recover. */
for (area = 0; area < nr_vms; area++) {
if (vas[area])
continue;
vas[area] = kmem_cache_zalloc(
vmap_area_cachep, GFP_KERNEL);
if (!vas[area])
goto err_free;
}
goto retry;
}
err_free:
for (area = 0; area < nr_vms; area++) {
mm/vmalloc.c: keep track of free blocks for vmap allocation Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18 05:31:31 +08:00
if (vas[area])
kmem_cache_free(vmap_area_cachep, vas[area]);
kfree(vms[area]);
}
err_free2:
kfree(vas);
kfree(vms);
return NULL;
err_free_shadow:
spin_lock(&free_vmap_area_lock);
/*
* We release all the vmalloc shadows, even the ones for regions that
* hadn't been successfully added. This relies on kasan_release_vmalloc
* being able to tolerate this case.
*/
for (area = 0; area < nr_vms; area++) {
orig_start = vas[area]->va_start;
orig_end = vas[area]->va_end;
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
va = merge_or_add_vmap_area_augment(vas[area], &free_vmap_area_root,
&free_vmap_area_list);
if (va)
kasan_release_vmalloc(orig_start, orig_end,
va->va_start, va->va_end);
vas[area] = NULL;
kfree(vms[area]);
}
spin_unlock(&free_vmap_area_lock);
kfree(vas);
kfree(vms);
return NULL;
}
/**
* pcpu_free_vm_areas - free vmalloc areas for percpu allocator
* @vms: vm_struct pointer array returned by pcpu_get_vm_areas()
* @nr_vms: the number of allocated areas
*
* Free vm_structs and the array allocated by pcpu_get_vm_areas().
*/
void pcpu_free_vm_areas(struct vm_struct **vms, int nr_vms)
{
int i;
for (i = 0; i < nr_vms; i++)
free_vm_area(vms[i]);
kfree(vms);
}
#endif /* CONFIG_SMP */
2008-04-28 17:12:40 +08:00
#ifdef CONFIG_PRINTK
bool vmalloc_dump_obj(void *object)
{
const void *caller;
struct vm_struct *vm;
struct vmap_area *va;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn;
unsigned long addr;
unsigned int nr_pages;
addr = PAGE_ALIGN((unsigned long) object);
vn = addr_to_node(addr);
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
if (!spin_trylock(&vn->busy.lock))
return false;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
va = __find_vmap_area(addr, &vn->busy.root);
if (!va || !va->vm) {
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
spin_unlock(&vn->busy.lock);
return false;
}
vm = va->vm;
addr = (unsigned long) vm->addr;
caller = vm->caller;
nr_pages = vm->nr_pages;
spin_unlock(&vn->busy.lock);
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
pr_cont(" %u-page vmalloc region starting at %#lx allocated at %pS\n",
nr_pages, addr, caller);
return true;
}
#endif
2008-04-28 17:12:40 +08:00
#ifdef CONFIG_PROC_FS
vmallocinfo: add NUMA information Christoph recently added /proc/vmallocinfo file to get information about vmalloc allocations. This patch adds NUMA specific information, giving number of pages allocated on each memory node. This should help to check that vmalloc() is able to respect NUMA policies. Example of output on a four nodes machine (one cpu per node) 1) network hash tables are evenly spreaded on four nodes (OK) (Same point for inodes and dentries hash tables) 2) iptables tables (x_tables) are correctly allocated on each cpu node (OK). 3) sys_swapon() allocates its memory from one node only. 4) each loaded module is using memory on one node. Sysadmins could tune their setup to change points 3) and 4) if necessary. grep "pages=" /proc/vmallocinfo 0xffffc20000000000-0xffffc20000201000 2101248 alloc_large_system_hash+0x204/0x2c0 pages=512 vmalloc N0=128 N1=128 N2=128 N3=128 0xffffc20000201000-0xffffc20000302000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc2000031a000-0xffffc2000031d000 12288 alloc_large_system_hash+0x204/0x2c0 pages=2 vmalloc N1=1 N2=1 0xffffc2000031f000-0xffffc2000032b000 49152 cramfs_uncompress_init+0x2e/0x80 pages=11 vmalloc N0=3 N1=3 N2=2 N3=3 0xffffc2000033e000-0xffffc20000341000 12288 sys_swapon+0x640/0xac0 pages=2 vmalloc N0=2 0xffffc20000341000-0xffffc20000344000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N0=2 0xffffc20000344000-0xffffc20000347000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N1=2 0xffffc20000347000-0xffffc2000034a000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N2=2 0xffffc2000034a000-0xffffc2000034d000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N3=2 0xffffc20004381000-0xffffc20004402000 528384 alloc_large_system_hash+0x204/0x2c0 pages=128 vmalloc N0=32 N1=32 N2=32 N3=32 0xffffc20004402000-0xffffc20004803000 4198400 alloc_large_system_hash+0x204/0x2c0 pages=1024 vmalloc vpages N0=256 N1=256 N2=256 N3=256 0xffffc20004803000-0xffffc20004904000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc20004904000-0xffffc20004bec000 3047424 sys_swapon+0x640/0xac0 pages=743 vmalloc vpages N0=743 0xffffffffa0000000-0xffffffffa000f000 61440 sys_init_module+0xc27/0x1d00 pages=14 vmalloc N1=14 0xffffffffa000f000-0xffffffffa0014000 20480 sys_init_module+0xc27/0x1d00 pages=4 vmalloc N0=4 0xffffffffa0014000-0xffffffffa0017000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N0=2 0xffffffffa0017000-0xffffffffa0022000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N1=10 0xffffffffa0022000-0xffffffffa0028000 24576 sys_init_module+0xc27/0x1d00 pages=5 vmalloc N3=5 0xffffffffa0028000-0xffffffffa0050000 163840 sys_init_module+0xc27/0x1d00 pages=39 vmalloc N1=39 0xffffffffa0050000-0xffffffffa0052000 8192 sys_init_module+0xc27/0x1d00 pages=1 vmalloc N1=1 0xffffffffa0052000-0xffffffffa0056000 16384 sys_init_module+0xc27/0x1d00 pages=3 vmalloc N1=3 0xffffffffa0056000-0xffffffffa0081000 176128 sys_init_module+0xc27/0x1d00 pages=42 vmalloc N3=42 0xffffffffa0081000-0xffffffffa00ae000 184320 sys_init_module+0xc27/0x1d00 pages=44 vmalloc N3=44 0xffffffffa00ae000-0xffffffffa00b1000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00b1000-0xffffffffa00b9000 32768 sys_init_module+0xc27/0x1d00 pages=7 vmalloc N0=7 0xffffffffa00b9000-0xffffffffa00c4000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N3=10 0xffffffffa00c6000-0xffffffffa00e0000 106496 sys_init_module+0xc27/0x1d00 pages=25 vmalloc N2=25 0xffffffffa00e0000-0xffffffffa00f1000 69632 sys_init_module+0xc27/0x1d00 pages=16 vmalloc N2=16 0xffffffffa00f1000-0xffffffffa00f4000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00f4000-0xffffffffa00f7000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 [akpm@linux-foundation.org: fix comment] Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 12:27:38 +08:00
static void show_numa_info(struct seq_file *m, struct vm_struct *v)
{
if (IS_ENABLED(CONFIG_NUMA)) {
vmallocinfo: add NUMA information Christoph recently added /proc/vmallocinfo file to get information about vmalloc allocations. This patch adds NUMA specific information, giving number of pages allocated on each memory node. This should help to check that vmalloc() is able to respect NUMA policies. Example of output on a four nodes machine (one cpu per node) 1) network hash tables are evenly spreaded on four nodes (OK) (Same point for inodes and dentries hash tables) 2) iptables tables (x_tables) are correctly allocated on each cpu node (OK). 3) sys_swapon() allocates its memory from one node only. 4) each loaded module is using memory on one node. Sysadmins could tune their setup to change points 3) and 4) if necessary. grep "pages=" /proc/vmallocinfo 0xffffc20000000000-0xffffc20000201000 2101248 alloc_large_system_hash+0x204/0x2c0 pages=512 vmalloc N0=128 N1=128 N2=128 N3=128 0xffffc20000201000-0xffffc20000302000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc2000031a000-0xffffc2000031d000 12288 alloc_large_system_hash+0x204/0x2c0 pages=2 vmalloc N1=1 N2=1 0xffffc2000031f000-0xffffc2000032b000 49152 cramfs_uncompress_init+0x2e/0x80 pages=11 vmalloc N0=3 N1=3 N2=2 N3=3 0xffffc2000033e000-0xffffc20000341000 12288 sys_swapon+0x640/0xac0 pages=2 vmalloc N0=2 0xffffc20000341000-0xffffc20000344000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N0=2 0xffffc20000344000-0xffffc20000347000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N1=2 0xffffc20000347000-0xffffc2000034a000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N2=2 0xffffc2000034a000-0xffffc2000034d000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N3=2 0xffffc20004381000-0xffffc20004402000 528384 alloc_large_system_hash+0x204/0x2c0 pages=128 vmalloc N0=32 N1=32 N2=32 N3=32 0xffffc20004402000-0xffffc20004803000 4198400 alloc_large_system_hash+0x204/0x2c0 pages=1024 vmalloc vpages N0=256 N1=256 N2=256 N3=256 0xffffc20004803000-0xffffc20004904000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc20004904000-0xffffc20004bec000 3047424 sys_swapon+0x640/0xac0 pages=743 vmalloc vpages N0=743 0xffffffffa0000000-0xffffffffa000f000 61440 sys_init_module+0xc27/0x1d00 pages=14 vmalloc N1=14 0xffffffffa000f000-0xffffffffa0014000 20480 sys_init_module+0xc27/0x1d00 pages=4 vmalloc N0=4 0xffffffffa0014000-0xffffffffa0017000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N0=2 0xffffffffa0017000-0xffffffffa0022000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N1=10 0xffffffffa0022000-0xffffffffa0028000 24576 sys_init_module+0xc27/0x1d00 pages=5 vmalloc N3=5 0xffffffffa0028000-0xffffffffa0050000 163840 sys_init_module+0xc27/0x1d00 pages=39 vmalloc N1=39 0xffffffffa0050000-0xffffffffa0052000 8192 sys_init_module+0xc27/0x1d00 pages=1 vmalloc N1=1 0xffffffffa0052000-0xffffffffa0056000 16384 sys_init_module+0xc27/0x1d00 pages=3 vmalloc N1=3 0xffffffffa0056000-0xffffffffa0081000 176128 sys_init_module+0xc27/0x1d00 pages=42 vmalloc N3=42 0xffffffffa0081000-0xffffffffa00ae000 184320 sys_init_module+0xc27/0x1d00 pages=44 vmalloc N3=44 0xffffffffa00ae000-0xffffffffa00b1000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00b1000-0xffffffffa00b9000 32768 sys_init_module+0xc27/0x1d00 pages=7 vmalloc N0=7 0xffffffffa00b9000-0xffffffffa00c4000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N3=10 0xffffffffa00c6000-0xffffffffa00e0000 106496 sys_init_module+0xc27/0x1d00 pages=25 vmalloc N2=25 0xffffffffa00e0000-0xffffffffa00f1000 69632 sys_init_module+0xc27/0x1d00 pages=16 vmalloc N2=16 0xffffffffa00f1000-0xffffffffa00f4000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00f4000-0xffffffffa00f7000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 [akpm@linux-foundation.org: fix comment] Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 12:27:38 +08:00
unsigned int nr, *counters = m->private;
unsigned int step = 1U << vm_area_page_order(v);
vmallocinfo: add NUMA information Christoph recently added /proc/vmallocinfo file to get information about vmalloc allocations. This patch adds NUMA specific information, giving number of pages allocated on each memory node. This should help to check that vmalloc() is able to respect NUMA policies. Example of output on a four nodes machine (one cpu per node) 1) network hash tables are evenly spreaded on four nodes (OK) (Same point for inodes and dentries hash tables) 2) iptables tables (x_tables) are correctly allocated on each cpu node (OK). 3) sys_swapon() allocates its memory from one node only. 4) each loaded module is using memory on one node. Sysadmins could tune their setup to change points 3) and 4) if necessary. grep "pages=" /proc/vmallocinfo 0xffffc20000000000-0xffffc20000201000 2101248 alloc_large_system_hash+0x204/0x2c0 pages=512 vmalloc N0=128 N1=128 N2=128 N3=128 0xffffc20000201000-0xffffc20000302000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc2000031a000-0xffffc2000031d000 12288 alloc_large_system_hash+0x204/0x2c0 pages=2 vmalloc N1=1 N2=1 0xffffc2000031f000-0xffffc2000032b000 49152 cramfs_uncompress_init+0x2e/0x80 pages=11 vmalloc N0=3 N1=3 N2=2 N3=3 0xffffc2000033e000-0xffffc20000341000 12288 sys_swapon+0x640/0xac0 pages=2 vmalloc N0=2 0xffffc20000341000-0xffffc20000344000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N0=2 0xffffc20000344000-0xffffc20000347000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N1=2 0xffffc20000347000-0xffffc2000034a000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N2=2 0xffffc2000034a000-0xffffc2000034d000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N3=2 0xffffc20004381000-0xffffc20004402000 528384 alloc_large_system_hash+0x204/0x2c0 pages=128 vmalloc N0=32 N1=32 N2=32 N3=32 0xffffc20004402000-0xffffc20004803000 4198400 alloc_large_system_hash+0x204/0x2c0 pages=1024 vmalloc vpages N0=256 N1=256 N2=256 N3=256 0xffffc20004803000-0xffffc20004904000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc20004904000-0xffffc20004bec000 3047424 sys_swapon+0x640/0xac0 pages=743 vmalloc vpages N0=743 0xffffffffa0000000-0xffffffffa000f000 61440 sys_init_module+0xc27/0x1d00 pages=14 vmalloc N1=14 0xffffffffa000f000-0xffffffffa0014000 20480 sys_init_module+0xc27/0x1d00 pages=4 vmalloc N0=4 0xffffffffa0014000-0xffffffffa0017000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N0=2 0xffffffffa0017000-0xffffffffa0022000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N1=10 0xffffffffa0022000-0xffffffffa0028000 24576 sys_init_module+0xc27/0x1d00 pages=5 vmalloc N3=5 0xffffffffa0028000-0xffffffffa0050000 163840 sys_init_module+0xc27/0x1d00 pages=39 vmalloc N1=39 0xffffffffa0050000-0xffffffffa0052000 8192 sys_init_module+0xc27/0x1d00 pages=1 vmalloc N1=1 0xffffffffa0052000-0xffffffffa0056000 16384 sys_init_module+0xc27/0x1d00 pages=3 vmalloc N1=3 0xffffffffa0056000-0xffffffffa0081000 176128 sys_init_module+0xc27/0x1d00 pages=42 vmalloc N3=42 0xffffffffa0081000-0xffffffffa00ae000 184320 sys_init_module+0xc27/0x1d00 pages=44 vmalloc N3=44 0xffffffffa00ae000-0xffffffffa00b1000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00b1000-0xffffffffa00b9000 32768 sys_init_module+0xc27/0x1d00 pages=7 vmalloc N0=7 0xffffffffa00b9000-0xffffffffa00c4000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N3=10 0xffffffffa00c6000-0xffffffffa00e0000 106496 sys_init_module+0xc27/0x1d00 pages=25 vmalloc N2=25 0xffffffffa00e0000-0xffffffffa00f1000 69632 sys_init_module+0xc27/0x1d00 pages=16 vmalloc N2=16 0xffffffffa00f1000-0xffffffffa00f4000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00f4000-0xffffffffa00f7000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 [akpm@linux-foundation.org: fix comment] Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 12:27:38 +08:00
if (!counters)
return;
if (v->flags & VM_UNINITIALIZED)
return;
/* Pair with smp_wmb() in clear_vm_uninitialized_flag() */
smp_rmb();
vmallocinfo: add NUMA information Christoph recently added /proc/vmallocinfo file to get information about vmalloc allocations. This patch adds NUMA specific information, giving number of pages allocated on each memory node. This should help to check that vmalloc() is able to respect NUMA policies. Example of output on a four nodes machine (one cpu per node) 1) network hash tables are evenly spreaded on four nodes (OK) (Same point for inodes and dentries hash tables) 2) iptables tables (x_tables) are correctly allocated on each cpu node (OK). 3) sys_swapon() allocates its memory from one node only. 4) each loaded module is using memory on one node. Sysadmins could tune their setup to change points 3) and 4) if necessary. grep "pages=" /proc/vmallocinfo 0xffffc20000000000-0xffffc20000201000 2101248 alloc_large_system_hash+0x204/0x2c0 pages=512 vmalloc N0=128 N1=128 N2=128 N3=128 0xffffc20000201000-0xffffc20000302000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc2000031a000-0xffffc2000031d000 12288 alloc_large_system_hash+0x204/0x2c0 pages=2 vmalloc N1=1 N2=1 0xffffc2000031f000-0xffffc2000032b000 49152 cramfs_uncompress_init+0x2e/0x80 pages=11 vmalloc N0=3 N1=3 N2=2 N3=3 0xffffc2000033e000-0xffffc20000341000 12288 sys_swapon+0x640/0xac0 pages=2 vmalloc N0=2 0xffffc20000341000-0xffffc20000344000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N0=2 0xffffc20000344000-0xffffc20000347000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N1=2 0xffffc20000347000-0xffffc2000034a000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N2=2 0xffffc2000034a000-0xffffc2000034d000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N3=2 0xffffc20004381000-0xffffc20004402000 528384 alloc_large_system_hash+0x204/0x2c0 pages=128 vmalloc N0=32 N1=32 N2=32 N3=32 0xffffc20004402000-0xffffc20004803000 4198400 alloc_large_system_hash+0x204/0x2c0 pages=1024 vmalloc vpages N0=256 N1=256 N2=256 N3=256 0xffffc20004803000-0xffffc20004904000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc20004904000-0xffffc20004bec000 3047424 sys_swapon+0x640/0xac0 pages=743 vmalloc vpages N0=743 0xffffffffa0000000-0xffffffffa000f000 61440 sys_init_module+0xc27/0x1d00 pages=14 vmalloc N1=14 0xffffffffa000f000-0xffffffffa0014000 20480 sys_init_module+0xc27/0x1d00 pages=4 vmalloc N0=4 0xffffffffa0014000-0xffffffffa0017000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N0=2 0xffffffffa0017000-0xffffffffa0022000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N1=10 0xffffffffa0022000-0xffffffffa0028000 24576 sys_init_module+0xc27/0x1d00 pages=5 vmalloc N3=5 0xffffffffa0028000-0xffffffffa0050000 163840 sys_init_module+0xc27/0x1d00 pages=39 vmalloc N1=39 0xffffffffa0050000-0xffffffffa0052000 8192 sys_init_module+0xc27/0x1d00 pages=1 vmalloc N1=1 0xffffffffa0052000-0xffffffffa0056000 16384 sys_init_module+0xc27/0x1d00 pages=3 vmalloc N1=3 0xffffffffa0056000-0xffffffffa0081000 176128 sys_init_module+0xc27/0x1d00 pages=42 vmalloc N3=42 0xffffffffa0081000-0xffffffffa00ae000 184320 sys_init_module+0xc27/0x1d00 pages=44 vmalloc N3=44 0xffffffffa00ae000-0xffffffffa00b1000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00b1000-0xffffffffa00b9000 32768 sys_init_module+0xc27/0x1d00 pages=7 vmalloc N0=7 0xffffffffa00b9000-0xffffffffa00c4000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N3=10 0xffffffffa00c6000-0xffffffffa00e0000 106496 sys_init_module+0xc27/0x1d00 pages=25 vmalloc N2=25 0xffffffffa00e0000-0xffffffffa00f1000 69632 sys_init_module+0xc27/0x1d00 pages=16 vmalloc N2=16 0xffffffffa00f1000-0xffffffffa00f4000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00f4000-0xffffffffa00f7000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 [akpm@linux-foundation.org: fix comment] Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 12:27:38 +08:00
memset(counters, 0, nr_node_ids * sizeof(unsigned int));
for (nr = 0; nr < v->nr_pages; nr += step)
counters[page_to_nid(v->pages[nr])] += step;
vmallocinfo: add NUMA information Christoph recently added /proc/vmallocinfo file to get information about vmalloc allocations. This patch adds NUMA specific information, giving number of pages allocated on each memory node. This should help to check that vmalloc() is able to respect NUMA policies. Example of output on a four nodes machine (one cpu per node) 1) network hash tables are evenly spreaded on four nodes (OK) (Same point for inodes and dentries hash tables) 2) iptables tables (x_tables) are correctly allocated on each cpu node (OK). 3) sys_swapon() allocates its memory from one node only. 4) each loaded module is using memory on one node. Sysadmins could tune their setup to change points 3) and 4) if necessary. grep "pages=" /proc/vmallocinfo 0xffffc20000000000-0xffffc20000201000 2101248 alloc_large_system_hash+0x204/0x2c0 pages=512 vmalloc N0=128 N1=128 N2=128 N3=128 0xffffc20000201000-0xffffc20000302000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc2000031a000-0xffffc2000031d000 12288 alloc_large_system_hash+0x204/0x2c0 pages=2 vmalloc N1=1 N2=1 0xffffc2000031f000-0xffffc2000032b000 49152 cramfs_uncompress_init+0x2e/0x80 pages=11 vmalloc N0=3 N1=3 N2=2 N3=3 0xffffc2000033e000-0xffffc20000341000 12288 sys_swapon+0x640/0xac0 pages=2 vmalloc N0=2 0xffffc20000341000-0xffffc20000344000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N0=2 0xffffc20000344000-0xffffc20000347000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N1=2 0xffffc20000347000-0xffffc2000034a000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N2=2 0xffffc2000034a000-0xffffc2000034d000 12288 xt_alloc_table_info+0xfe/0x130 [x_tables] pages=2 vmalloc N3=2 0xffffc20004381000-0xffffc20004402000 528384 alloc_large_system_hash+0x204/0x2c0 pages=128 vmalloc N0=32 N1=32 N2=32 N3=32 0xffffc20004402000-0xffffc20004803000 4198400 alloc_large_system_hash+0x204/0x2c0 pages=1024 vmalloc vpages N0=256 N1=256 N2=256 N3=256 0xffffc20004803000-0xffffc20004904000 1052672 alloc_large_system_hash+0x204/0x2c0 pages=256 vmalloc N0=64 N1=64 N2=64 N3=64 0xffffc20004904000-0xffffc20004bec000 3047424 sys_swapon+0x640/0xac0 pages=743 vmalloc vpages N0=743 0xffffffffa0000000-0xffffffffa000f000 61440 sys_init_module+0xc27/0x1d00 pages=14 vmalloc N1=14 0xffffffffa000f000-0xffffffffa0014000 20480 sys_init_module+0xc27/0x1d00 pages=4 vmalloc N0=4 0xffffffffa0014000-0xffffffffa0017000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N0=2 0xffffffffa0017000-0xffffffffa0022000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N1=10 0xffffffffa0022000-0xffffffffa0028000 24576 sys_init_module+0xc27/0x1d00 pages=5 vmalloc N3=5 0xffffffffa0028000-0xffffffffa0050000 163840 sys_init_module+0xc27/0x1d00 pages=39 vmalloc N1=39 0xffffffffa0050000-0xffffffffa0052000 8192 sys_init_module+0xc27/0x1d00 pages=1 vmalloc N1=1 0xffffffffa0052000-0xffffffffa0056000 16384 sys_init_module+0xc27/0x1d00 pages=3 vmalloc N1=3 0xffffffffa0056000-0xffffffffa0081000 176128 sys_init_module+0xc27/0x1d00 pages=42 vmalloc N3=42 0xffffffffa0081000-0xffffffffa00ae000 184320 sys_init_module+0xc27/0x1d00 pages=44 vmalloc N3=44 0xffffffffa00ae000-0xffffffffa00b1000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00b1000-0xffffffffa00b9000 32768 sys_init_module+0xc27/0x1d00 pages=7 vmalloc N0=7 0xffffffffa00b9000-0xffffffffa00c4000 45056 sys_init_module+0xc27/0x1d00 pages=10 vmalloc N3=10 0xffffffffa00c6000-0xffffffffa00e0000 106496 sys_init_module+0xc27/0x1d00 pages=25 vmalloc N2=25 0xffffffffa00e0000-0xffffffffa00f1000 69632 sys_init_module+0xc27/0x1d00 pages=16 vmalloc N2=16 0xffffffffa00f1000-0xffffffffa00f4000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 0xffffffffa00f4000-0xffffffffa00f7000 12288 sys_init_module+0xc27/0x1d00 pages=2 vmalloc N3=2 [akpm@linux-foundation.org: fix comment] Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 12:27:38 +08:00
for_each_node_state(nr, N_HIGH_MEMORY)
if (counters[nr])
seq_printf(m, " N%u=%u", nr, counters[nr]);
}
}
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
static void show_purge_info(struct seq_file *m)
{
struct vmap_node *vn;
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
struct vmap_area *va;
int i;
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
for (i = 0; i < nr_vmap_nodes; i++) {
vn = &vmap_nodes[i];
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
spin_lock(&vn->lazy.lock);
list_for_each_entry(va, &vn->lazy.head, list) {
seq_printf(m, "0x%pK-0x%pK %7ld unpurged vm_area\n",
(void *)va->va_start, (void *)va->va_end,
va->va_end - va->va_start);
}
spin_unlock(&vn->lazy.lock);
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
}
}
static int vmalloc_info_show(struct seq_file *m, void *p)
2008-04-28 17:12:40 +08:00
{
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn;
struct vmap_area *va;
2013-04-30 06:07:35 +08:00
struct vm_struct *v;
int i;
2013-04-30 06:07:35 +08:00
for (i = 0; i < nr_vmap_nodes; i++) {
vn = &vmap_nodes[i];
spin_lock(&vn->busy.lock);
list_for_each_entry(va, &vn->busy.head, list) {
if (!va->vm) {
if (va->flags & VMAP_RAM)
seq_printf(m, "0x%pK-0x%pK %7ld vm_map_ram\n",
(void *)va->va_start, (void *)va->va_end,
va->va_end - va->va_start);
vmalloc: show lazy-purged vma info in vmallocinfo When ioremap a 67112960 bytes vm_area with the vmallocinfo: [..] 0xec79b000-0xec7fa000 389120 ftl_add_mtd+0x4d0/0x754 pages=94 vmalloc 0xec800000-0xecbe1000 4067328 kbox_proc_mem_write+0x104/0x1c4 phys=8b520000 ioremap we get the result: 0xf1000000-0xf5001000 67112960 devm_ioremap+0x38/0x7c phys=40000000 ioremap For the align for ioremap must be less than '1 << IOREMAP_MAX_ORDER': if (flags & VM_IOREMAP) align = 1ul << clamp_t(int, get_count_order_long(size), PAGE_SHIFT, IOREMAP_MAX_ORDER); So it makes idiot like me a litte puzzled why this was a jump the vm_area from 0xec800000-0xecbe1000 to 0xf1000000-0xf5001000, and leaving 0xed000000-0xf1000000 as a big hole. This patch is to show all of vm_area, including vmas which are freeing but still in the vmap_area_list, to make it more clear about why we will get 0xf1000000-0xf5001000 in the above case. And we will get a vmallocinfo like: [..] 0xec79b000-0xec7fa000 389120 ftl_add_mtd+0x4d0/0x754 pages=94 vmalloc 0xec800000-0xecbe1000 4067328 kbox_proc_mem_write+0x104/0x1c4 phys=8b520000 ioremap [..] 0xece7c000-0xece7e000 8192 unpurged vm_area 0xece7e000-0xece83000 20480 vm_map_ram 0xf0099000-0xf00aa000 69632 vm_map_ram after this patch. Link: http://lkml.kernel.org/r/1496649682-20710-1-git-send-email-xieyisheng1@huawei.com Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: zijun_hu <zijun_hu@htc.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-07-11 06:48:09 +08:00
continue;
}
2013-04-30 06:07:35 +08:00
v = va->vm;
2008-04-28 17:12:40 +08:00
seq_printf(m, "0x%pK-0x%pK %7ld",
v->addr, v->addr + v->size, v->size);
2008-04-28 17:12:40 +08:00
if (v->caller)
seq_printf(m, " %pS", v->caller);
vmallocinfo: add caller information Add caller information so that /proc/vmallocinfo shows where the allocation request for a slice of vmalloc memory originated. Results in output like this: 0xffffc20000000000-0xffffc20000801000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20000801000-0xffffc20000806000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000806000-0xffffc20000c07000 4198400 alloc_large_system_hash+0x127/0x246 pages=1024 vmalloc vpages 0xffffc20000c07000-0xffffc20000c0a000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c0a000-0xffffc20000c0c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c0c000-0xffffc20000c0f000 12288 acpi_os_map_memory+0x13/0x1c phys=cff64000 ioremap 0xffffc20000c10000-0xffffc20000c15000 20480 acpi_os_map_memory+0x13/0x1c phys=cff65000 ioremap 0xffffc20000c16000-0xffffc20000c18000 8192 acpi_os_map_memory+0x13/0x1c phys=cff69000 ioremap 0xffffc20000c18000-0xffffc20000c1a000 8192 acpi_os_map_memory+0x13/0x1c phys=fed1f000 ioremap 0xffffc20000c1a000-0xffffc20000c1c000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1c000-0xffffc20000c1e000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c1e000-0xffffc20000c20000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c20000-0xffffc20000c22000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c22000-0xffffc20000c24000 8192 acpi_os_map_memory+0x13/0x1c phys=cff68000 ioremap 0xffffc20000c24000-0xffffc20000c26000 8192 acpi_os_map_memory+0x13/0x1c phys=e0081000 ioremap 0xffffc20000c26000-0xffffc20000c28000 8192 acpi_os_map_memory+0x13/0x1c phys=e0080000 ioremap 0xffffc20000c28000-0xffffc20000c2d000 20480 alloc_large_system_hash+0x127/0x246 pages=4 vmalloc 0xffffc20000c2d000-0xffffc20000c31000 16384 tcp_init+0xd5/0x31c pages=3 vmalloc 0xffffc20000c31000-0xffffc20000c34000 12288 alloc_large_system_hash+0x127/0x246 pages=2 vmalloc 0xffffc20000c34000-0xffffc20000c36000 8192 init_vdso_vars+0xde/0x1f1 0xffffc20000c36000-0xffffc20000c38000 8192 pci_iomap+0x8a/0xb4 phys=d8e00000 ioremap 0xffffc20000c38000-0xffffc20000c3a000 8192 usb_hcd_pci_probe+0x139/0x295 [usbcore] phys=d8e00000 ioremap 0xffffc20000c3a000-0xffffc20000c3e000 16384 sys_swapon+0x509/0xa15 pages=3 vmalloc 0xffffc20000c40000-0xffffc20000c61000 135168 e1000_probe+0x1c4/0xa32 phys=d8a20000 ioremap 0xffffc20000c61000-0xffffc20000c6a000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c6a000-0xffffc20000c73000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c73000-0xffffc20000c7c000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20000c7c000-0xffffc20000c7f000 12288 e1000e_setup_tx_resources+0x29/0xbe pages=2 vmalloc 0xffffc20000c80000-0xffffc20001481000 8392704 pci_mmcfg_arch_init+0x90/0x118 phys=e0000000 ioremap 0xffffc20001481000-0xffffc20001682000 2101248 alloc_large_system_hash+0x127/0x246 pages=512 vmalloc 0xffffc20001682000-0xffffc20001e83000 8392704 alloc_large_system_hash+0x127/0x246 pages=2048 vmalloc vpages 0xffffc20001e83000-0xffffc20002204000 3674112 alloc_large_system_hash+0x127/0x246 pages=896 vmalloc vpages 0xffffc20002204000-0xffffc2000220d000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000220d000-0xffffc20002216000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002216000-0xffffc2000221f000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc2000221f000-0xffffc20002228000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002228000-0xffffc20002231000 36864 _xfs_buf_map_pages+0x8e/0xc0 vmap 0xffffc20002231000-0xffffc20002234000 12288 e1000e_setup_rx_resources+0x35/0x122 pages=2 vmalloc 0xffffc20002240000-0xffffc20002261000 135168 e1000_probe+0x1c4/0xa32 phys=d8a60000 ioremap 0xffffc20002261000-0xffffc2000270c000 4894720 sys_swapon+0x509/0xa15 pages=1194 vmalloc vpages 0xffffffffa0000000-0xffffffffa0022000 139264 module_alloc+0x4f/0x55 pages=33 vmalloc 0xffffffffa0022000-0xffffffffa0029000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc 0xffffffffa002b000-0xffffffffa0034000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa0034000-0xffffffffa003d000 36864 module_alloc+0x4f/0x55 pages=8 vmalloc 0xffffffffa003d000-0xffffffffa0049000 49152 module_alloc+0x4f/0x55 pages=11 vmalloc 0xffffffffa0049000-0xffffffffa0050000 28672 module_alloc+0x4f/0x55 pages=6 vmalloc [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Lameter <clameter@sgi.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 17:12:42 +08:00
if (v->nr_pages)
seq_printf(m, " pages=%d", v->nr_pages);
2008-04-28 17:12:40 +08:00
if (v->phys_addr)
seq_printf(m, " phys=%pa", &v->phys_addr);
2008-04-28 17:12:40 +08:00
if (v->flags & VM_IOREMAP)
seq_puts(m, " ioremap");
2008-04-28 17:12:40 +08:00
- Sumanth Korikkar has taught s390 to allocate hotplug-time page frames from hotplugged memory rather than only from main memory. Series "implement "memmap on memory" feature on s390". - More folio conversions from Matthew Wilcox in the series "Convert memcontrol charge moving to use folios" "mm: convert mm counter to take a folio" - Chengming Zhou has optimized zswap's rbtree locking, providing significant reductions in system time and modest but measurable reductions in overall runtimes. The series is "mm/zswap: optimize the scalability of zswap rb-tree". - Chengming Zhou has also provided the series "mm/zswap: optimize zswap lru list" which provides measurable runtime benefits in some swap-intensive situations. - And Chengming Zhou further optimizes zswap in the series "mm/zswap: optimize for dynamic zswap_pools". Measured improvements are modest. - zswap cleanups and simplifications from Yosry Ahmed in the series "mm: zswap: simplify zswap_swapoff()". - In the series "Add DAX ABI for memmap_on_memory", Vishal Verma has contributed several DAX cleanups as well as adding a sysfs tunable to control the memmap_on_memory setting when the dax device is hotplugged as system memory. - Johannes Weiner has added the large series "mm: zswap: cleanups", which does that. - More DAMON work from SeongJae Park in the series "mm/damon: make DAMON debugfs interface deprecation unignorable" "selftests/damon: add more tests for core functionalities and corner cases" "Docs/mm/damon: misc readability improvements" "mm/damon: let DAMOS feeds and tame/auto-tune itself" - In the series "mm/mempolicy: weighted interleave mempolicy and sysfs extension" Rakie Kim has developed a new mempolicy interleaving policy wherein we allocate memory across nodes in a weighted fashion rather than uniformly. This is beneficial in heterogeneous memory environments appearing with CXL. - Christophe Leroy has contributed some cleanup and consolidation work against the ARM pagetable dumping code in the series "mm: ptdump: Refactor CONFIG_DEBUG_WX and check_wx_pages debugfs attribute". - Luis Chamberlain has added some additional xarray selftesting in the series "test_xarray: advanced API multi-index tests". - Muhammad Usama Anjum has reworked the selftest code to make its human-readable output conform to the TAP ("Test Anything Protocol") format. Amongst other things, this opens up the use of third-party tools to parse and process out selftesting results. - Ryan Roberts has added fork()-time PTE batching of THP ptes in the series "mm/memory: optimize fork() with PTE-mapped THP". Mainly targeted at arm64, this significantly speeds up fork() when the process has a large number of pte-mapped folios. - David Hildenbrand also gets in on the THP pte batching game in his series "mm/memory: optimize unmap/zap with PTE-mapped THP". It implements batching during munmap() and other pte teardown situations. The microbenchmark improvements are nice. - And in the series "Transparent Contiguous PTEs for User Mappings" Ryan Roberts further utilizes arm's pte's contiguous bit ("contpte mappings"). Kernel build times on arm64 improved nicely. Ryan's series "Address some contpte nits" provides some followup work. - In the series "mm/hugetlb: Restore the reservation" Breno Leitao has fixed an obscure hugetlb race which was causing unnecessary page faults. He has also added a reproducer under the selftest code. - In the series "selftests/mm: Output cleanups for the compaction test", Mark Brown did what the title claims. - Kinsey Ho has added the series "mm/mglru: code cleanup and refactoring". - Even more zswap material from Nhat Pham. The series "fix and extend zswap kselftests" does as claimed. - In the series "Introduce cpu_dcache_is_aliasing() to fix DAX regression" Mathieu Desnoyers has cleaned up and fixed rather a mess in our handling of DAX on archiecctures which have virtually aliasing data caches. The arm architecture is the main beneficiary. - Lokesh Gidra's series "per-vma locks in userfaultfd" provides dramatic improvements in worst-case mmap_lock hold times during certain userfaultfd operations. - Some page_owner enhancements and maintenance work from Oscar Salvador in his series "page_owner: print stacks and their outstanding allocations" "page_owner: Fixup and cleanup" - Uladzislau Rezki has contributed some vmalloc scalability improvements in his series "Mitigate a vmap lock contention". It realizes a 12x improvement for a certain microbenchmark. - Some kexec/crash cleanup work from Baoquan He in the series "Split crash out from kexec and clean up related config items". - Some zsmalloc maintenance work from Chengming Zhou in the series "mm/zsmalloc: fix and optimize objects/page migration" "mm/zsmalloc: some cleanup for get/set_zspage_mapping()" - Zi Yan has taught the MM to perform compaction on folios larger than order=0. This a step along the path to implementaton of the merging of large anonymous folios. The series is named "Enable >0 order folio memory compaction". - Christoph Hellwig has done quite a lot of cleanup work in the pagecache writeback code in his series "convert write_cache_pages() to an iterator". - Some modest hugetlb cleanups and speedups in Vishal Moola's series "Handle hugetlb faults under the VMA lock". - Zi Yan has changed the page splitting code so we can split huge pages into sizes other than order-0 to better utilize large folios. The series is named "Split a folio to any lower order folios". - David Hildenbrand has contributed the series "mm: remove total_mapcount()", a cleanup. - Matthew Wilcox has sought to improve the performance of bulk memory freeing in his series "Rearrange batched folio freeing". - Gang Li's series "hugetlb: parallelize hugetlb page init on boot" provides large improvements in bootup times on large machines which are configured to use large numbers of hugetlb pages. - Matthew Wilcox's series "PageFlags cleanups" does that. - Qi Zheng's series "minor fixes and supplement for ptdesc" does that also. S390 is affected. - Cleanups to our pagemap utility functions from Peter Xu in his series "mm/treewide: Replace pXd_large() with pXd_leaf()". - Nico Pache has fixed a few things with our hugepage selftests in his series "selftests/mm: Improve Hugepage Test Handling in MM Selftests". - Also, of course, many singleton patches to many things. Please see the individual changelogs for details. -----BEGIN PGP SIGNATURE----- iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZfJpPQAKCRDdBJ7gKXxA joxeAP9TrcMEuHnLmBlhIXkWbIR4+ki+pA3v+gNTlJiBhnfVSgD9G55t1aBaRplx TMNhHfyiHYDTx/GAV9NXW84tasJSDgA= =TG55 -----END PGP SIGNATURE----- Merge tag 'mm-stable-2024-03-13-20-04' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm Pull MM updates from Andrew Morton: - Sumanth Korikkar has taught s390 to allocate hotplug-time page frames from hotplugged memory rather than only from main memory. Series "implement "memmap on memory" feature on s390". - More folio conversions from Matthew Wilcox in the series "Convert memcontrol charge moving to use folios" "mm: convert mm counter to take a folio" - Chengming Zhou has optimized zswap's rbtree locking, providing significant reductions in system time and modest but measurable reductions in overall runtimes. The series is "mm/zswap: optimize the scalability of zswap rb-tree". - Chengming Zhou has also provided the series "mm/zswap: optimize zswap lru list" which provides measurable runtime benefits in some swap-intensive situations. - And Chengming Zhou further optimizes zswap in the series "mm/zswap: optimize for dynamic zswap_pools". Measured improvements are modest. - zswap cleanups and simplifications from Yosry Ahmed in the series "mm: zswap: simplify zswap_swapoff()". - In the series "Add DAX ABI for memmap_on_memory", Vishal Verma has contributed several DAX cleanups as well as adding a sysfs tunable to control the memmap_on_memory setting when the dax device is hotplugged as system memory. - Johannes Weiner has added the large series "mm: zswap: cleanups", which does that. - More DAMON work from SeongJae Park in the series "mm/damon: make DAMON debugfs interface deprecation unignorable" "selftests/damon: add more tests for core functionalities and corner cases" "Docs/mm/damon: misc readability improvements" "mm/damon: let DAMOS feeds and tame/auto-tune itself" - In the series "mm/mempolicy: weighted interleave mempolicy and sysfs extension" Rakie Kim has developed a new mempolicy interleaving policy wherein we allocate memory across nodes in a weighted fashion rather than uniformly. This is beneficial in heterogeneous memory environments appearing with CXL. - Christophe Leroy has contributed some cleanup and consolidation work against the ARM pagetable dumping code in the series "mm: ptdump: Refactor CONFIG_DEBUG_WX and check_wx_pages debugfs attribute". - Luis Chamberlain has added some additional xarray selftesting in the series "test_xarray: advanced API multi-index tests". - Muhammad Usama Anjum has reworked the selftest code to make its human-readable output conform to the TAP ("Test Anything Protocol") format. Amongst other things, this opens up the use of third-party tools to parse and process out selftesting results. - Ryan Roberts has added fork()-time PTE batching of THP ptes in the series "mm/memory: optimize fork() with PTE-mapped THP". Mainly targeted at arm64, this significantly speeds up fork() when the process has a large number of pte-mapped folios. - David Hildenbrand also gets in on the THP pte batching game in his series "mm/memory: optimize unmap/zap with PTE-mapped THP". It implements batching during munmap() and other pte teardown situations. The microbenchmark improvements are nice. - And in the series "Transparent Contiguous PTEs for User Mappings" Ryan Roberts further utilizes arm's pte's contiguous bit ("contpte mappings"). Kernel build times on arm64 improved nicely. Ryan's series "Address some contpte nits" provides some followup work. - In the series "mm/hugetlb: Restore the reservation" Breno Leitao has fixed an obscure hugetlb race which was causing unnecessary page faults. He has also added a reproducer under the selftest code. - In the series "selftests/mm: Output cleanups for the compaction test", Mark Brown did what the title claims. - Kinsey Ho has added the series "mm/mglru: code cleanup and refactoring". - Even more zswap material from Nhat Pham. The series "fix and extend zswap kselftests" does as claimed. - In the series "Introduce cpu_dcache_is_aliasing() to fix DAX regression" Mathieu Desnoyers has cleaned up and fixed rather a mess in our handling of DAX on archiecctures which have virtually aliasing data caches. The arm architecture is the main beneficiary. - Lokesh Gidra's series "per-vma locks in userfaultfd" provides dramatic improvements in worst-case mmap_lock hold times during certain userfaultfd operations. - Some page_owner enhancements and maintenance work from Oscar Salvador in his series "page_owner: print stacks and their outstanding allocations" "page_owner: Fixup and cleanup" - Uladzislau Rezki has contributed some vmalloc scalability improvements in his series "Mitigate a vmap lock contention". It realizes a 12x improvement for a certain microbenchmark. - Some kexec/crash cleanup work from Baoquan He in the series "Split crash out from kexec and clean up related config items". - Some zsmalloc maintenance work from Chengming Zhou in the series "mm/zsmalloc: fix and optimize objects/page migration" "mm/zsmalloc: some cleanup for get/set_zspage_mapping()" - Zi Yan has taught the MM to perform compaction on folios larger than order=0. This a step along the path to implementaton of the merging of large anonymous folios. The series is named "Enable >0 order folio memory compaction". - Christoph Hellwig has done quite a lot of cleanup work in the pagecache writeback code in his series "convert write_cache_pages() to an iterator". - Some modest hugetlb cleanups and speedups in Vishal Moola's series "Handle hugetlb faults under the VMA lock". - Zi Yan has changed the page splitting code so we can split huge pages into sizes other than order-0 to better utilize large folios. The series is named "Split a folio to any lower order folios". - David Hildenbrand has contributed the series "mm: remove total_mapcount()", a cleanup. - Matthew Wilcox has sought to improve the performance of bulk memory freeing in his series "Rearrange batched folio freeing". - Gang Li's series "hugetlb: parallelize hugetlb page init on boot" provides large improvements in bootup times on large machines which are configured to use large numbers of hugetlb pages. - Matthew Wilcox's series "PageFlags cleanups" does that. - Qi Zheng's series "minor fixes and supplement for ptdesc" does that also. S390 is affected. - Cleanups to our pagemap utility functions from Peter Xu in his series "mm/treewide: Replace pXd_large() with pXd_leaf()". - Nico Pache has fixed a few things with our hugepage selftests in his series "selftests/mm: Improve Hugepage Test Handling in MM Selftests". - Also, of course, many singleton patches to many things. Please see the individual changelogs for details. * tag 'mm-stable-2024-03-13-20-04' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (435 commits) mm/zswap: remove the memcpy if acomp is not sleepable crypto: introduce: acomp_is_async to expose if comp drivers might sleep memtest: use {READ,WRITE}_ONCE in memory scanning mm: prohibit the last subpage from reusing the entire large folio mm: recover pud_leaf() definitions in nopmd case selftests/mm: skip the hugetlb-madvise tests on unmet hugepage requirements selftests/mm: skip uffd hugetlb tests with insufficient hugepages selftests/mm: dont fail testsuite due to a lack of hugepages mm/huge_memory: skip invalid debugfs new_order input for folio split mm/huge_memory: check new folio order when split a folio mm, vmscan: retry kswapd's priority loop with cache_trim_mode off on failure mm: add an explicit smp_wmb() to UFFDIO_CONTINUE mm: fix list corruption in put_pages_list mm: remove folio from deferred split list before uncharging it filemap: avoid unnecessary major faults in filemap_fault() mm,page_owner: drop unnecessary check mm,page_owner: check for null stack_record before bumping its refcount mm: swap: fix race between free_swap_and_cache() and swapoff() mm/treewide: align up pXd_leaf() retval across archs mm/treewide: drop pXd_large() ...
2024-03-15 08:43:30 +08:00
if (v->flags & VM_SPARSE)
seq_puts(m, " sparse");
mm: Introduce VM_SPARSE kind and vm_area_[un]map_pages(). vmap/vmalloc APIs are used to map a set of pages into contiguous kernel virtual space. get_vm_area() with appropriate flag is used to request an area of kernel address range. It's used for vmalloc, vmap, ioremap, xen use cases. - vmalloc use case dominates the usage. Such vm areas have VM_ALLOC flag. - the areas created by vmap() function should be tagged with VM_MAP. - ioremap areas are tagged with VM_IOREMAP. BPF would like to extend the vmap API to implement a lazily-populated sparse, yet contiguous kernel virtual space. Introduce VM_SPARSE flag and vm_area_map_pages(area, start_addr, count, pages) API to map a set of pages within a given area. It has the same sanity checks as vmap() does. It also checks that get_vm_area() was created with VM_SPARSE flag which identifies such areas in /proc/vmallocinfo and returns zero pages on read through /proc/kcore. The next commits will introduce bpf_arena which is a sparsely populated shared memory region between bpf program and user space process. It will map privately-managed pages into a sparse vm area with the following steps: // request virtual memory region during bpf prog verification area = get_vm_area(area_size, VM_SPARSE); // on demand vm_area_map_pages(area, kaddr, kend, pages); vm_area_unmap_pages(area, kaddr, kend); // after bpf program is detached and unloaded free_vm_area(area); Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com> Link: https://lore.kernel.org/bpf/20240305030516.41519-3-alexei.starovoitov@gmail.com
2024-03-05 11:05:16 +08:00
if (v->flags & VM_ALLOC)
seq_puts(m, " vmalloc");
2008-04-28 17:12:40 +08:00
if (v->flags & VM_MAP)
seq_puts(m, " vmap");
2008-04-28 17:12:40 +08:00
if (v->flags & VM_USERMAP)
seq_puts(m, " user");
2008-04-28 17:12:40 +08:00
if (v->flags & VM_DMA_COHERENT)
seq_puts(m, " dma-coherent");
if (is_vmalloc_addr(v->pages))
seq_puts(m, " vpages");
2008-04-28 17:12:40 +08:00
show_numa_info(m, v);
seq_putc(m, '\n');
}
spin_unlock(&vn->busy.lock);
}
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
/*
mm/vmalloc: rework the drain logic A current "lazy drain" model suffers from at least two issues. First one is related to the unsorted list of vmap areas, thus in order to identify the [min:max] range of areas to be drained, it requires a full list scan. What is a time consuming if the list is too long. Second one and as a next step is about merging all fragments with a free space. What is also a time consuming because it has to iterate over entire list which holds outstanding lazy areas. See below the "preemptirqsoff" tracer that illustrates a high latency. It is ~24676us. Our workloads like audio and video are effected by such long latency: <snip> tracer: preemptirqsoff preemptirqsoff latency trace v1.1.5 on 4.9.186-perf+ -------------------------------------------------------------------- latency: 24676 us, #4/4, CPU#1 | (M:preempt VP:0, KP:0, SP:0 HP:0 P:8) ----------------- | task: crtc_commit:112-261 (uid:0 nice:0 policy:1 rt_prio:16) ----------------- => started at: __purge_vmap_area_lazy => ended at: __purge_vmap_area_lazy _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / crtc_com-261 1...1 1us*: _raw_spin_lock <-__purge_vmap_area_lazy [...] crtc_com-261 1...1 24675us : _raw_spin_unlock <-__purge_vmap_area_lazy crtc_com-261 1...1 24677us : trace_preempt_on <-__purge_vmap_area_lazy crtc_com-261 1...1 24683us : <stack trace> => free_vmap_area_noflush => remove_vm_area => __vunmap => vfree => drm_property_free_blob => drm_mode_object_unreference => drm_property_unreference_blob => __drm_atomic_helper_crtc_destroy_state => sde_crtc_destroy_state => drm_atomic_state_default_clear => drm_atomic_state_clear => drm_atomic_state_free => complete_commit => _msm_drm_commit_work_cb => kthread_worker_fn => kthread => ret_from_fork <snip> To address those two issues we can redesign a purging of the outstanding lazy areas. Instead of queuing vmap areas to the list, we replace it by the separate rb-tree. In hat case an area is located in the tree/list in ascending order. It will give us below advantages: a) Outstanding vmap areas are merged creating bigger coalesced blocks, thus it becomes less fragmented. b) It is possible to calculate a flush range [min:max] without scanning all elements. It is O(1) access time or complexity; c) The final merge of areas with the rb-tree that represents a free space is faster because of (a). As a result the lock contention is also reduced. Link: https://lkml.kernel.org/r/20201116220033.1837-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Minchan Kim <minchan@kernel.org> Cc: huang ying <huang.ying.caritas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-15 11:08:49 +08:00
* As a final step, dump "unpurged" areas.
mm/vmalloc: do not keep unpurged areas in the busy tree The busy tree can be quite big, even though the area is freed or unmapped it still stays there until "purge" logic removes it. 1) Optimize and reduce the size of "busy" tree by removing a node from it right away as soon as user triggers free paths. It is possible to do so, because the allocation is done using another augmented tree. The vmalloc test driver shows the difference, for example the "fix_size_alloc_test" is ~11% better comparing with default configuration: sudo ./test_vmalloc.sh performance <default> Summary: fix_size_alloc_test loops: 1000000 avg: 993985 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973554 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12617652 usec <default> <this patch> Summary: fix_size_alloc_test loops: 1000000 avg: 882263 usec Summary: full_fit_alloc_test loops: 1000000 avg: 973407 usec Summary: long_busy_list_alloc_test loops: 1000000 avg: 12593929 usec <this patch> 2) Since the busy tree now contains allocated areas only and does not interfere with lazily free nodes, introduce the new function show_purge_info() that dumps "unpurged" areas that is propagated through "/proc/vmallocinfo". 3) Eliminate VM_LAZY_FREE flag. Link: http://lkml.kernel.org/r/20190716152656.12255-2-lpf.vector@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Pengfei Li <lpf.vector@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-24 06:36:36 +08:00
*/
show_purge_info(m);
2008-04-28 17:12:40 +08:00
return 0;
}
static int __init proc_vmalloc_init(void)
{
void *priv_data = NULL;
if (IS_ENABLED(CONFIG_NUMA))
priv_data = kmalloc(nr_node_ids * sizeof(unsigned int), GFP_KERNEL);
proc_create_single_data("vmallocinfo",
0400, NULL, vmalloc_info_show, priv_data);
return 0;
}
module_init(proc_vmalloc_init);
2008-04-28 17:12:40 +08:00
#endif
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
static void __init vmap_init_free_space(void)
{
unsigned long vmap_start = 1;
const unsigned long vmap_end = ULONG_MAX;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_area *free;
struct vm_struct *busy;
/*
* B F B B B F
* -|-----|.....|-----|-----|-----|.....|-
* | The KVA space |
* |<--------------------------------->|
*/
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
for (busy = vmlist; busy; busy = busy->next) {
if ((unsigned long) busy->addr - vmap_start > 0) {
free = kmem_cache_zalloc(vmap_area_cachep, GFP_NOWAIT);
if (!WARN_ON_ONCE(!free)) {
free->va_start = vmap_start;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
free->va_end = (unsigned long) busy->addr;
insert_vmap_area_augment(free, NULL,
&free_vmap_area_root,
&free_vmap_area_list);
}
}
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
vmap_start = (unsigned long) busy->addr + busy->size;
}
if (vmap_end - vmap_start > 0) {
free = kmem_cache_zalloc(vmap_area_cachep, GFP_NOWAIT);
if (!WARN_ON_ONCE(!free)) {
free->va_start = vmap_start;
free->va_end = vmap_end;
insert_vmap_area_augment(free, NULL,
&free_vmap_area_root,
&free_vmap_area_list);
}
}
}
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
static void vmap_init_nodes(void)
{
struct vmap_node *vn;
mm: vmalloc: set nr_nodes based on CPUs in a system A number of nodes which are used in the alloc/free paths is set based on num_possible_cpus() in a system. Please note a high limit threshold though is fixed and corresponds to 128 nodes. For 32-bit or single core systems an access to a global vmap heap is not balanced. Such small systems do not suffer from lock contentions due to low number of CPUs. In such case the nr_nodes is equal to 1. Test on AMD Ryzen Threadripper 3970X 32-Core Processor: sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 <default perf> 94.41% 0.89% [kernel] [k] _raw_spin_lock 93.35% 93.07% [kernel] [k] native_queued_spin_lock_slowpath 76.13% 0.28% [kernel] [k] __vmalloc_node_range 72.96% 0.81% [kernel] [k] alloc_vmap_area 56.94% 0.00% [kernel] [k] __get_vm_area_node 41.95% 0.00% [kernel] [k] vmalloc 37.15% 0.01% [test_vmalloc] [k] full_fit_alloc_test 35.17% 0.00% [kernel] [k] ret_from_fork_asm 35.17% 0.00% [kernel] [k] ret_from_fork 35.17% 0.00% [kernel] [k] kthread 35.08% 0.00% [test_vmalloc] [k] test_func 34.45% 0.00% [test_vmalloc] [k] fix_size_alloc_test 28.09% 0.01% [test_vmalloc] [k] long_busy_list_alloc_test 23.53% 0.25% [kernel] [k] vfree.part.0 21.72% 0.00% [kernel] [k] remove_vm_area 20.08% 0.21% [kernel] [k] find_unlink_vmap_area 2.34% 0.61% [kernel] [k] free_vmap_area_noflush <default perf> vs <patch-series perf> 82.32% 0.22% [test_vmalloc] [k] long_busy_list_alloc_test 63.36% 0.02% [kernel] [k] vmalloc 63.34% 2.64% [kernel] [k] __vmalloc_node_range 30.42% 4.46% [kernel] [k] vfree.part.0 28.98% 2.51% [kernel] [k] __alloc_pages_bulk 27.28% 0.19% [kernel] [k] __get_vm_area_node 26.13% 1.50% [kernel] [k] alloc_vmap_area 21.72% 21.67% [kernel] [k] clear_page_rep 19.51% 2.43% [kernel] [k] _raw_spin_lock 16.61% 16.51% [kernel] [k] native_queued_spin_lock_slowpath 13.40% 2.07% [kernel] [k] free_unref_page 10.62% 0.01% [kernel] [k] remove_vm_area 9.02% 8.73% [kernel] [k] insert_vmap_area 8.94% 0.00% [kernel] [k] ret_from_fork_asm 8.94% 0.00% [kernel] [k] ret_from_fork 8.94% 0.00% [kernel] [k] kthread 8.29% 0.00% [test_vmalloc] [k] test_func 7.81% 0.05% [test_vmalloc] [k] full_fit_alloc_test 5.30% 4.73% [kernel] [k] purge_vmap_node 4.47% 2.65% [kernel] [k] free_vmap_area_noflush <patch-series perf> confirms that a native_queued_spin_lock_slowpath goes down to 16.51% percent from 93.07%. The throughput is ~12x higher: urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 10m51.271s user 0m0.013s sys 0m0.187s urezki@pc638:~$ urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 0m51.301s user 0m0.015s sys 0m0.040s urezki@pc638:~$ Link: https://lkml.kernel.org/r/20240102184633.748113-11-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:32 +08:00
int i, n;
#if BITS_PER_LONG == 64
/*
* A high threshold of max nodes is fixed and bound to 128,
* thus a scale factor is 1 for systems where number of cores
* are less or equal to specified threshold.
*
* As for NUMA-aware notes. For bigger systems, for example
* NUMA with multi-sockets, where we can end-up with thousands
* of cores in total, a "sub-numa-clustering" should be added.
*
* In this case a NUMA domain is considered as a single entity
* with dedicated sub-nodes in it which describe one group or
* set of cores. Therefore a per-domain purging is supposed to
* be added as well as a per-domain balancing.
*/
mm: vmalloc: set nr_nodes based on CPUs in a system A number of nodes which are used in the alloc/free paths is set based on num_possible_cpus() in a system. Please note a high limit threshold though is fixed and corresponds to 128 nodes. For 32-bit or single core systems an access to a global vmap heap is not balanced. Such small systems do not suffer from lock contentions due to low number of CPUs. In such case the nr_nodes is equal to 1. Test on AMD Ryzen Threadripper 3970X 32-Core Processor: sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 <default perf> 94.41% 0.89% [kernel] [k] _raw_spin_lock 93.35% 93.07% [kernel] [k] native_queued_spin_lock_slowpath 76.13% 0.28% [kernel] [k] __vmalloc_node_range 72.96% 0.81% [kernel] [k] alloc_vmap_area 56.94% 0.00% [kernel] [k] __get_vm_area_node 41.95% 0.00% [kernel] [k] vmalloc 37.15% 0.01% [test_vmalloc] [k] full_fit_alloc_test 35.17% 0.00% [kernel] [k] ret_from_fork_asm 35.17% 0.00% [kernel] [k] ret_from_fork 35.17% 0.00% [kernel] [k] kthread 35.08% 0.00% [test_vmalloc] [k] test_func 34.45% 0.00% [test_vmalloc] [k] fix_size_alloc_test 28.09% 0.01% [test_vmalloc] [k] long_busy_list_alloc_test 23.53% 0.25% [kernel] [k] vfree.part.0 21.72% 0.00% [kernel] [k] remove_vm_area 20.08% 0.21% [kernel] [k] find_unlink_vmap_area 2.34% 0.61% [kernel] [k] free_vmap_area_noflush <default perf> vs <patch-series perf> 82.32% 0.22% [test_vmalloc] [k] long_busy_list_alloc_test 63.36% 0.02% [kernel] [k] vmalloc 63.34% 2.64% [kernel] [k] __vmalloc_node_range 30.42% 4.46% [kernel] [k] vfree.part.0 28.98% 2.51% [kernel] [k] __alloc_pages_bulk 27.28% 0.19% [kernel] [k] __get_vm_area_node 26.13% 1.50% [kernel] [k] alloc_vmap_area 21.72% 21.67% [kernel] [k] clear_page_rep 19.51% 2.43% [kernel] [k] _raw_spin_lock 16.61% 16.51% [kernel] [k] native_queued_spin_lock_slowpath 13.40% 2.07% [kernel] [k] free_unref_page 10.62% 0.01% [kernel] [k] remove_vm_area 9.02% 8.73% [kernel] [k] insert_vmap_area 8.94% 0.00% [kernel] [k] ret_from_fork_asm 8.94% 0.00% [kernel] [k] ret_from_fork 8.94% 0.00% [kernel] [k] kthread 8.29% 0.00% [test_vmalloc] [k] test_func 7.81% 0.05% [test_vmalloc] [k] full_fit_alloc_test 5.30% 4.73% [kernel] [k] purge_vmap_node 4.47% 2.65% [kernel] [k] free_vmap_area_noflush <patch-series perf> confirms that a native_queued_spin_lock_slowpath goes down to 16.51% percent from 93.07%. The throughput is ~12x higher: urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 10m51.271s user 0m0.013s sys 0m0.187s urezki@pc638:~$ urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 0m51.301s user 0m0.015s sys 0m0.040s urezki@pc638:~$ Link: https://lkml.kernel.org/r/20240102184633.748113-11-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:32 +08:00
n = clamp_t(unsigned int, num_possible_cpus(), 1, 128);
if (n > 1) {
vn = kmalloc_array(n, sizeof(*vn), GFP_NOWAIT | __GFP_NOWARN);
if (vn) {
/* Node partition is 16 pages. */
vmap_zone_size = (1 << 4) * PAGE_SIZE;
nr_vmap_nodes = n;
vmap_nodes = vn;
} else {
pr_err("Failed to allocate an array. Disable a node layer\n");
}
}
#endif
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
mm: vmalloc: set nr_nodes based on CPUs in a system A number of nodes which are used in the alloc/free paths is set based on num_possible_cpus() in a system. Please note a high limit threshold though is fixed and corresponds to 128 nodes. For 32-bit or single core systems an access to a global vmap heap is not balanced. Such small systems do not suffer from lock contentions due to low number of CPUs. In such case the nr_nodes is equal to 1. Test on AMD Ryzen Threadripper 3970X 32-Core Processor: sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 <default perf> 94.41% 0.89% [kernel] [k] _raw_spin_lock 93.35% 93.07% [kernel] [k] native_queued_spin_lock_slowpath 76.13% 0.28% [kernel] [k] __vmalloc_node_range 72.96% 0.81% [kernel] [k] alloc_vmap_area 56.94% 0.00% [kernel] [k] __get_vm_area_node 41.95% 0.00% [kernel] [k] vmalloc 37.15% 0.01% [test_vmalloc] [k] full_fit_alloc_test 35.17% 0.00% [kernel] [k] ret_from_fork_asm 35.17% 0.00% [kernel] [k] ret_from_fork 35.17% 0.00% [kernel] [k] kthread 35.08% 0.00% [test_vmalloc] [k] test_func 34.45% 0.00% [test_vmalloc] [k] fix_size_alloc_test 28.09% 0.01% [test_vmalloc] [k] long_busy_list_alloc_test 23.53% 0.25% [kernel] [k] vfree.part.0 21.72% 0.00% [kernel] [k] remove_vm_area 20.08% 0.21% [kernel] [k] find_unlink_vmap_area 2.34% 0.61% [kernel] [k] free_vmap_area_noflush <default perf> vs <patch-series perf> 82.32% 0.22% [test_vmalloc] [k] long_busy_list_alloc_test 63.36% 0.02% [kernel] [k] vmalloc 63.34% 2.64% [kernel] [k] __vmalloc_node_range 30.42% 4.46% [kernel] [k] vfree.part.0 28.98% 2.51% [kernel] [k] __alloc_pages_bulk 27.28% 0.19% [kernel] [k] __get_vm_area_node 26.13% 1.50% [kernel] [k] alloc_vmap_area 21.72% 21.67% [kernel] [k] clear_page_rep 19.51% 2.43% [kernel] [k] _raw_spin_lock 16.61% 16.51% [kernel] [k] native_queued_spin_lock_slowpath 13.40% 2.07% [kernel] [k] free_unref_page 10.62% 0.01% [kernel] [k] remove_vm_area 9.02% 8.73% [kernel] [k] insert_vmap_area 8.94% 0.00% [kernel] [k] ret_from_fork_asm 8.94% 0.00% [kernel] [k] ret_from_fork 8.94% 0.00% [kernel] [k] kthread 8.29% 0.00% [test_vmalloc] [k] test_func 7.81% 0.05% [test_vmalloc] [k] full_fit_alloc_test 5.30% 4.73% [kernel] [k] purge_vmap_node 4.47% 2.65% [kernel] [k] free_vmap_area_noflush <patch-series perf> confirms that a native_queued_spin_lock_slowpath goes down to 16.51% percent from 93.07%. The throughput is ~12x higher: urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 10m51.271s user 0m0.013s sys 0m0.187s urezki@pc638:~$ urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 0m51.301s user 0m0.015s sys 0m0.040s urezki@pc638:~$ Link: https://lkml.kernel.org/r/20240102184633.748113-11-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:32 +08:00
for (n = 0; n < nr_vmap_nodes; n++) {
vn = &vmap_nodes[n];
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
vn->busy.root = RB_ROOT;
INIT_LIST_HEAD(&vn->busy.head);
spin_lock_init(&vn->busy.lock);
vn->lazy.root = RB_ROOT;
INIT_LIST_HEAD(&vn->lazy.head);
spin_lock_init(&vn->lazy.lock);
mm: vmalloc: set nr_nodes based on CPUs in a system A number of nodes which are used in the alloc/free paths is set based on num_possible_cpus() in a system. Please note a high limit threshold though is fixed and corresponds to 128 nodes. For 32-bit or single core systems an access to a global vmap heap is not balanced. Such small systems do not suffer from lock contentions due to low number of CPUs. In such case the nr_nodes is equal to 1. Test on AMD Ryzen Threadripper 3970X 32-Core Processor: sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 <default perf> 94.41% 0.89% [kernel] [k] _raw_spin_lock 93.35% 93.07% [kernel] [k] native_queued_spin_lock_slowpath 76.13% 0.28% [kernel] [k] __vmalloc_node_range 72.96% 0.81% [kernel] [k] alloc_vmap_area 56.94% 0.00% [kernel] [k] __get_vm_area_node 41.95% 0.00% [kernel] [k] vmalloc 37.15% 0.01% [test_vmalloc] [k] full_fit_alloc_test 35.17% 0.00% [kernel] [k] ret_from_fork_asm 35.17% 0.00% [kernel] [k] ret_from_fork 35.17% 0.00% [kernel] [k] kthread 35.08% 0.00% [test_vmalloc] [k] test_func 34.45% 0.00% [test_vmalloc] [k] fix_size_alloc_test 28.09% 0.01% [test_vmalloc] [k] long_busy_list_alloc_test 23.53% 0.25% [kernel] [k] vfree.part.0 21.72% 0.00% [kernel] [k] remove_vm_area 20.08% 0.21% [kernel] [k] find_unlink_vmap_area 2.34% 0.61% [kernel] [k] free_vmap_area_noflush <default perf> vs <patch-series perf> 82.32% 0.22% [test_vmalloc] [k] long_busy_list_alloc_test 63.36% 0.02% [kernel] [k] vmalloc 63.34% 2.64% [kernel] [k] __vmalloc_node_range 30.42% 4.46% [kernel] [k] vfree.part.0 28.98% 2.51% [kernel] [k] __alloc_pages_bulk 27.28% 0.19% [kernel] [k] __get_vm_area_node 26.13% 1.50% [kernel] [k] alloc_vmap_area 21.72% 21.67% [kernel] [k] clear_page_rep 19.51% 2.43% [kernel] [k] _raw_spin_lock 16.61% 16.51% [kernel] [k] native_queued_spin_lock_slowpath 13.40% 2.07% [kernel] [k] free_unref_page 10.62% 0.01% [kernel] [k] remove_vm_area 9.02% 8.73% [kernel] [k] insert_vmap_area 8.94% 0.00% [kernel] [k] ret_from_fork_asm 8.94% 0.00% [kernel] [k] ret_from_fork 8.94% 0.00% [kernel] [k] kthread 8.29% 0.00% [test_vmalloc] [k] test_func 7.81% 0.05% [test_vmalloc] [k] full_fit_alloc_test 5.30% 4.73% [kernel] [k] purge_vmap_node 4.47% 2.65% [kernel] [k] free_vmap_area_noflush <patch-series perf> confirms that a native_queued_spin_lock_slowpath goes down to 16.51% percent from 93.07%. The throughput is ~12x higher: urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 10m51.271s user 0m0.013s sys 0m0.187s urezki@pc638:~$ urezki@pc638:~$ time sudo ./test_vmalloc.sh run_test_mask=7 nr_threads=64 Run the test with following parameters: run_test_mask=7 nr_threads=64 Done. Check the kernel ring buffer to see the summary. real 0m51.301s user 0m0.015s sys 0m0.040s urezki@pc638:~$ Link: https://lkml.kernel.org/r/20240102184633.748113-11-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:32 +08:00
for (i = 0; i < MAX_VA_SIZE_PAGES; i++) {
INIT_LIST_HEAD(&vn->pool[i].head);
WRITE_ONCE(vn->pool[i].len, 0);
}
spin_lock_init(&vn->pool_lock);
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
}
}
static unsigned long
vmap_node_shrink_count(struct shrinker *shrink, struct shrink_control *sc)
{
unsigned long count;
struct vmap_node *vn;
int i, j;
for (count = 0, i = 0; i < nr_vmap_nodes; i++) {
vn = &vmap_nodes[i];
for (j = 0; j < MAX_VA_SIZE_PAGES; j++)
count += READ_ONCE(vn->pool[j].len);
}
return count ? count : SHRINK_EMPTY;
}
static unsigned long
vmap_node_shrink_scan(struct shrinker *shrink, struct shrink_control *sc)
{
int i;
for (i = 0; i < nr_vmap_nodes; i++)
decay_va_pool_node(&vmap_nodes[i], true);
return SHRINK_STOP;
}
void __init vmalloc_init(void)
{
struct shrinker *vmap_node_shrinker;
struct vmap_area *va;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
struct vmap_node *vn;
struct vm_struct *tmp;
int i;
/*
* Create the cache for vmap_area objects.
*/
vmap_area_cachep = KMEM_CACHE(vmap_area, SLAB_PANIC);
for_each_possible_cpu(i) {
struct vmap_block_queue *vbq;
struct vfree_deferred *p;
vbq = &per_cpu(vmap_block_queue, i);
spin_lock_init(&vbq->lock);
INIT_LIST_HEAD(&vbq->free);
p = &per_cpu(vfree_deferred, i);
init_llist_head(&p->list);
INIT_WORK(&p->wq, delayed_vfree_work);
mm: vmalloc: remove a global vmap_blocks xarray A global vmap_blocks-xarray array can be contented under heavy usage of the vm_map_ram()/vm_unmap_ram() APIs. The lock_stat shows that a "vmap_blocks.xa_lock" lock is a second in a top-list when it comes to contentions: <snip> ---------------------------------------- class name con-bounces contentions ... ---------------------------------------- vmap_area_lock: 2554079 2554276 ... -------------- vmap_area_lock 1297948 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 1256330 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c95c05a7>] find_vm_area+0x16/0x70 -------------- vmap_area_lock 1738590 [<00000000dd41cbaa>] alloc_vmap_area+0x1c7/0x910 vmap_area_lock 815688 [<000000009d927bf3>] free_vmap_block+0x4a/0xe0 vmap_area_lock 1 [<00000000c1d619d7>] __get_vm_area_node+0xd2/0x170 vmap_blocks.xa_lock: 862689 862698 ... ------------------- vmap_blocks.xa_lock 378418 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 vmap_blocks.xa_lock 484280 [<00000000caa2ef03>] xa_erase+0xe/0x30 ------------------- vmap_blocks.xa_lock 576226 [<00000000caa2ef03>] xa_erase+0xe/0x30 vmap_blocks.xa_lock 286472 [<00000000625a5626>] vm_map_ram+0x359/0x4a0 ... <snip> that is a result of running vm_map_ram()/vm_unmap_ram() in a loop. The test creates 64(on 64 CPUs system) threads and each one maps/unmaps 1 page. After this change the "xa_lock" can be considered as a noise in the same test condition: <snip> ... &xa->xa_lock#1: 10333 10394 ... -------------- &xa->xa_lock#1 5349 [<00000000bbbc9751>] xa_erase+0xe/0x30 &xa->xa_lock#1 5045 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 -------------- &xa->xa_lock#1 7326 [<0000000018def45d>] vm_map_ram+0x3a4/0x4f0 &xa->xa_lock#1 3068 [<00000000bbbc9751>] xa_erase+0xe/0x30 ... <snip> Running the test_vmalloc.sh run_test_mask=1024 nr_threads=64 nr_pages=5 shows around ~8 percent of throughput improvement of vm_map_ram() and vm_unmap_ram() APIs. This patch does not fix vmap_area_lock/free_vmap_area_lock and purge_vmap_area_lock bottle-necks, it is rather a separate rework. Link: https://lkml.kernel.org/r/20230330190639.431589-1-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-31 03:06:38 +08:00
xa_init(&vbq->vmap_blocks);
}
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
/*
* Setup nodes before importing vmlist.
*/
vmap_init_nodes();
/* Import existing vmlist entries. */
for (tmp = vmlist; tmp; tmp = tmp->next) {
va = kmem_cache_zalloc(vmap_area_cachep, GFP_NOWAIT);
if (WARN_ON_ONCE(!va))
continue;
va->va_start = (unsigned long)tmp->addr;
va->va_end = va->va_start + tmp->size;
va->vm = tmp;
mm: vmalloc: remove global vmap_area_root rb-tree Store allocated objects in a separate nodes. A va->va_start address is converted into a correct node where it should be placed and resided. An addr_to_node() function is used to do a proper address conversion to determine a node that contains a VA. Such approach balances VAs across nodes as a result an access becomes scalable. Number of nodes in a system depends on number of CPUs. Please note: 1. As of now allocated VAs are bound to a node-0. It means the patch does not give any difference comparing with a current behavior; 2. The global vmap_area_lock, vmap_area_root are removed as there is no need in it anymore. The vmap_area_list is still kept and is _empty_. It is exported for a kexec only; 3. The vmallocinfo and vread() have to be reworked to be able to handle multiple nodes. [urezki@gmail.com: mark vmap_init_free_space() with __init tag] Link: https://lkml.kernel.org/r/20240111132628.299644-1-urezki@gmail.com [urezki@gmail.com: fix a wrong value passed to __find_vmap_area()] Link: https://lkml.kernel.org/r/20240111121104.180993-1-urezki@gmail.com Link: https://lkml.kernel.org/r/20240102184633.748113-5-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Joel Fernandes (Google) <joel@joelfernandes.org> Cc: Kazuhito Hagio <k-hagio-ab@nec.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sony.com> Cc: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-01-03 02:46:26 +08:00
vn = addr_to_node(va->va_start);
insert_vmap_area(va, &vn->busy.root, &vn->busy.head);
}
/*
* Now we can initialize a free vmap space.
*/
vmap_init_free_space();
vmap_initialized = true;
vmap_node_shrinker = shrinker_alloc(0, "vmap-node");
if (!vmap_node_shrinker) {
pr_err("Failed to allocate vmap-node shrinker!\n");
return;
}
vmap_node_shrinker->count_objects = vmap_node_shrink_count;
vmap_node_shrinker->scan_objects = vmap_node_shrink_scan;
shrinker_register(vmap_node_shrinker);
}