korg/linux
0
0
Fork 0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-12-27 04:54:41 +08:00
Code Issues Packages Projects Releases Wiki Activity
d34c671deb
linux/arch/arm/boot/dts/tegra30-cardhu-a04.dts

106 lines
2.5 KiB
Plaintext
Raw Normal View History

ARM: dt: tegra: cardhu: split dts file for support multiple board versions There is multiple version of cardhu starting from A01 to A07. Cardhu A01 and A03 are not supported. Cardhu A02 will have different sets of GPIOs for fixed regulator compare to cardhu A04. The Cardhu A05, A06, A07 are compatibe with A04. Based on cardhu version, the related dts file need to be chosen like for cardhu A02, use tegra30-cardhu-a02.dts, cardhu A04 and more, use tegra30-cardhu-a04.dts. This patch create the DTS file A02 and A04 and convert tegra30-cardhu.dts as dts include file. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-08-09 19:00:38 +08:00
/dts-v1/;
/include/ "tegra30-cardhu.dtsi"
/* This dts file support the cardhu A04 and later versions of board */
/ {
model = "NVIDIA Tegra30 Cardhu A04 (A05, A06, A07) evaluation board";
compatible = "nvidia,cardhu-a04", "nvidia,cardhu", "nvidia,tegra30";
ARM: tegra: cardhu: add dt entry for fixed regulators Cadhu have multiple power rails which are controlled by GPIOs. Add support of these power rail control through fixed regulators. Add entry for all fixed regulators for cardhu-a02 and a04. The details are taken from downstream kernel. Some points on this change are: * Add the tps65910-LDO5 entry and make it always ON to supply power to SDMMC. Once the sd driver support regulator handling, this flag will be remove. * Dropping registration of rail vdd_sdmmc1 as the gpio is used by sdhci power-gpio. This need to fix in sdhci driver and then need to add the registration mechanism. Just removing power-gpio and adding fixed regulator with this gpio is causing the sd access to fail because first probe call of this regulator fails due to non-available of parent and so it calls gpio_free() which disable the pins in gpio mode make pin output to LOW causes power to OFF. In probe retry, it got success and it powered-on but it again need to do again numeration of card here. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-08-09 19:00:39 +08:00
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
ddr_reg: regulator@100 {
compatible = "regulator-fixed";
regulator-name = "ddr";
reg = <100>;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
enable-active-high;
gpio = <&pmic 7 0>;
};
sys_3v3_reg: regulator@101 {
compatible = "regulator-fixed";
reg = <101>;
regulator-name = "sys_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
enable-active-high;
gpio = <&pmic 6 0>;
};
usb1_vbus_reg: regulator@102 {
compatible = "regulator-fixed";
reg = <102>;
regulator-name = "usb1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&gpio 238 0>; /* GPIO PDD6 */
gpio-open-drain;
vin-supply = <&vdd_5v0_reg>;
};
usb3_vbus_reg: regulator@103 {
compatible = "regulator-fixed";
reg = <103>;
regulator-name = "usb3_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&gpio 236 0>; /* GPIO PDD4 */
gpio-open-drain;
vin-supply = <&vdd_5v0_reg>;
};
vdd_5v0_reg: regulator@104 {
compatible = "regulator-fixed";
reg = <104>;
regulator-name = "5v0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&pmic 8 0>;
};
vdd_bl_reg: regulator@105 {
compatible = "regulator-fixed";
reg = <105>;
regulator-name = "vdd_bl";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
enable-active-high;
gpio = <&gpio 234 0>; /* GPIO PDD2 */
};
vdd_bl2_reg: regulator@106 {
compatible = "regulator-fixed";
reg = <106>;
regulator-name = "vdd_bl2";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
enable-active-high;
gpio = <&gpio 232 0>; /* GPIO PDD0 */
};
};
ARM: dt: t30 cardhu: set pinmux and power for wlan Configure pinmux as required for WiFi. Enable the SDHCI1 controller for a02 and a04 board, which is connected to the WiFi module. For now, always enable the regulator that provides power to the Wifi module. Signed-off-by: Wei Ni <wni@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-09-21 16:54:59 +08:00
sdhci@78000400 {
status = "okay";
power-gpios = <&gpio 27 0>; /* gpio PD3 */
bus-width = <4>;
ARM: tegra: add non-removable and keep-power-in-suspend property for MMC This patch adds "non-removable" property of MMC host where the eMMC device is for Tegra platform. And the "keep-power-in-suspend" property was used for the SDIO device that need this to go into suspend mode (e.g. BRCM43xx series). Signed-off-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-04-04 04:34:39 +08:00
keep-power-in-suspend;
ARM: dt: t30 cardhu: set pinmux and power for wlan Configure pinmux as required for WiFi. Enable the SDHCI1 controller for a02 and a04 board, which is connected to the WiFi module. For now, always enable the regulator that provides power to the Wifi module. Signed-off-by: Wei Ni <wni@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-09-21 16:54:59 +08:00
};
ARM: dt: tegra: cardhu: split dts file for support multiple board versions There is multiple version of cardhu starting from A01 to A07. Cardhu A01 and A03 are not supported. Cardhu A02 will have different sets of GPIOs for fixed regulator compare to cardhu A04. The Cardhu A05, A06, A07 are compatibe with A04. Based on cardhu version, the related dts file need to be chosen like for cardhu A02, use tegra30-cardhu-a02.dts, cardhu A04 and more, use tegra30-cardhu-a04.dts. This patch create the DTS file A02 and A04 and convert tegra30-cardhu.dts as dts include file. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-08-09 19:00:38 +08:00
};
Reference in New Issue Copy Permalink