linux/drivers/net/usb/Makefile

40 lines
1.5 KiB
Makefile
Raw Normal View History

#
# Makefile for USB Network drivers
#
obj-$(CONFIG_USB_CATC) += catc.o
obj-$(CONFIG_USB_KAWETH) += kaweth.o
obj-$(CONFIG_USB_PEGASUS) += pegasus.o
obj-$(CONFIG_USB_RTL8150) += rtl8150.o
obj-$(CONFIG_USB_RTL8152) += r8152.o
obj-$(CONFIG_USB_HSO) += hso.o
obj-$(CONFIG_USB_NET_AX8817X) += asix.o
asix-y := asix_devices.o asix_common.o ax88172a.o
2013-03-02 08:41:11 +08:00
obj-$(CONFIG_USB_NET_AX88179_178A) += ax88179_178a.o
obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o r815x.o
obj-$(CONFIG_USB_NET_CDC_EEM) += cdc_eem.o
obj-$(CONFIG_USB_NET_DM9601) += dm9601.o
obj-$(CONFIG_USB_NET_SR9700) += sr9700.o
obj-$(CONFIG_USB_NET_SMSC75XX) += smsc75xx.o
obj-$(CONFIG_USB_NET_SMSC95XX) += smsc95xx.o
obj-$(CONFIG_USB_NET_GL620A) += gl620a.o
obj-$(CONFIG_USB_NET_NET1080) += net1080.o
obj-$(CONFIG_USB_NET_PLUSB) += plusb.o
obj-$(CONFIG_USB_NET_RNDIS_HOST) += rndis_host.o
obj-$(CONFIG_USB_NET_CDC_SUBSET) += cdc_subset.o
obj-$(CONFIG_USB_NET_ZAURUS) += zaurus.o
obj-$(CONFIG_USB_NET_MCS7830) += mcs7830.o
obj-$(CONFIG_USB_USBNET) += usbnet.o
obj-$(CONFIG_USB_NET_INT51X1) += int51x1.o
obj-$(CONFIG_USB_CDC_PHONET) += cdc-phonet.o
obj-$(CONFIG_USB_NET_KALMIA) += kalmia.o
obj-$(CONFIG_USB_IPHETH) += ipheth.o
net/usb: add sierra_net.c driver Re-submitted based on comments from netdev community. Summary of the changes: 1. Improved error handling. 2. Added the missing timeout arguments to usb_control_msg(). The following is a new Linux driver which exposes certain models of Sierra Wireless modems to the operating system as Network Interface Cards (NICs). This driver requires a version of the sierra.c driver which supports blacklisting to work properly. The blacklist in sierra.c rejects the interfaces claimed by sierra_net.c. Likewise, the sierra_net.c driver only accepts (i.e. whitelists) the interface(s) used for USB-to-WWAN traffic. The version of sierra.c which supports blacklisting is available from the sierra wireless knowledge base page for older kernels. It is also available in Linux kernel starting from version 2.6.31. This driver works with all Sierra Wireless devices configured with PID=68A3 like USB305, USB306 provided the corresponding firmware version is I2.0 (for USB305) or M3.0 (for USB306) and later. This driver will not work with earlier firmware versions than the ones shown above. In this case the driver will issue an error message indicating incompatibility and will not serve the device's USB-to-WWAN interface. Sierra_net.c sits atop a pre-existing Linux driver called usbnet.c. A series of hook functions are provided in sierra_net.c which are called by usbnet.c in response to a particular condition such as receipt or transmission of a data packet. As such, usbnet.c does most of the work of making a modem appear to the system as a network device and for properly exchanging traffic between the USB subsystem and the Network card interface. Sierra_net.c is concerned with managing the data exchanged between the USB-to-WWAN interface and the upper layers of the operating system. Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com> Signed-off-by: Rory Filer <rfiler@sierrawireless.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-28 09:06:41 +08:00
obj-$(CONFIG_USB_SIERRA_NET) += sierra_net.o
introduce cx82310_eth: Conexant CX82310-based ADSL router USB ethernet driver This patch introduces cx82310_eth driver - driver for USB ethernet port of ADSL routers based on Conexant CX82310 chips. Such routers usually have ethernet port(s) too which are bridged together with the USB ethernet port, allowing the USB-connected machine to communicate to the network (and also internet through the ADSL, of course). This is my first driver, so please check thoroughly. As there's no protocol documentation, it was done with usbsnoop dumps from Windows driver, some parts (the commands) inspired by cxacru driver and also other usbnet drivers. The driver passed my testing - some real work and also pings sized from 0 to 65507 B. The only problem I found is the ifconfig error counter. When I return 0 (or 1 but empty skb) from rx_fixup(), usbnet increases the error counter although it's not an error condition (because packets can cross URB boundaries). Maybe the usbnet should be fixed to allow rx_fixup() to return empty skbs (or some other value, e.g. 2)? The USB ID of my device is 0x0572:0xcb01 which conflicts with some ADSL modems using cxacru driver (they probably use the same chipset but simpler firmware). The modems seem to use bDeviceClass 0 and iProduct "ADSL USB MODEM", my router uses bDeviceClass 255 and iProduct "USB NET CARD". The driver matches only devices with class 255 and checks for the iProduct string during init. I already posted a patch for the cxacru driver to ignore these devices. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-04 10:39:34 +08:00
obj-$(CONFIG_USB_NET_CX82310_ETH) += cx82310_eth.o
obj-$(CONFIG_USB_NET_CDC_NCM) += cdc_ncm.o
obj-$(CONFIG_USB_NET_HUAWEI_CDC_NCM) += huawei_cdc_ncm.o
obj-$(CONFIG_USB_VL600) += lg-vl600.o
obj-$(CONFIG_USB_NET_QMI_WWAN) += qmi_wwan.o
obj-$(CONFIG_USB_NET_CDC_MBIM) += cdc_mbim.o