linux/arch/arm/boot/dts/qcom-apq8064.dtsi

1763 lines
38 KiB
Plaintext
Raw Normal View History

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 22:07:57 +08:00
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include <dt-bindings/clock/qcom,gcc-msm8960.h>
#include <dt-bindings/reset/qcom,gcc-msm8960.h>
#include <dt-bindings/clock/qcom,mmcc-msm8960.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/soc/qcom,gsbi.h>
ARM: dts: MSM8064 remove flags from SPMI/MPP IRQs The Qualcomm PMIC GPIO and MPP lines are problematic: the are fetched from the main MFD driver with platform_get_irq() which means that at this point they will all be assigned the flags set up for the interrupts in the device tree. That is problematic since these are flagged as rising edge and an this point the interrupt descriptor is assigned a rising edge, while the only thing the GPIO/MPP drivers really do is issue irq_get_irqchip_state() on the line to read it out and to provide a .to_irq() helper for *other* IRQ consumers. If another device tree node tries to flag the same IRQ for use as something else than rising edge, the kernel irqdomain core will protest like this: type mismatch, failed to map hwirq-NN for <FOO>! Which is what happens when the device tree defines two contradictory flags for the same interrupt line. To work around this and alleviate the problem, assign 0 as flag for the interrupts taken by the PM GPIO and MPP drivers. This will lead to the flag being unset, and a second consumer requesting rising, falling, both or level interrupts will be respected. This is what the qcom-pm*.dtsi files already do. Switched to using the symbolic name IRQ_TYPE_NONE so that we get this more readable. Cc: stable@vger.kernel.org Fixes: bce360469676 ("ARM: dts: apq8064: add pm8921 mpp support") Fixes: 874443fe9e33 ("ARM: dts: apq8064: Add pm8921 mfd and its gpio node") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Björn Andersson <bjorn.andersson@linaro.org> Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Andy Gross <andy.gross@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2016-08-05 16:38:37 +08:00
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
model = "Qualcomm APQ8064";
compatible = "qcom,apq8064";
interrupt-parent = <&intc>;
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
smem_region: smem@80000000 {
reg = <0x80000000 0x200000>;
no-map;
};
wcnss_mem: wcnss@8f000000 {
reg = <0x8f000000 0x700000>;
no-map;
};
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
CPU0: cpu@0 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <0>;
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
cpu-idle-states = <&CPU_SPC>;
};
CPU1: cpu@1 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <1>;
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
cpu-idle-states = <&CPU_SPC>;
};
CPU2: cpu@2 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <2>;
next-level-cache = <&L2>;
qcom,acc = <&acc2>;
qcom,saw = <&saw2>;
cpu-idle-states = <&CPU_SPC>;
};
CPU3: cpu@3 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <3>;
next-level-cache = <&L2>;
qcom,acc = <&acc3>;
qcom,saw = <&saw3>;
cpu-idle-states = <&CPU_SPC>;
};
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
};
idle-states {
CPU_SPC: spc {
compatible = "qcom,idle-state-spc",
"arm,idle-state";
entry-latency-us = <400>;
exit-latency-us = <900>;
min-residency-us = <3000>;
};
};
};
memory {
device_type = "memory";
reg = <0x0 0x0>;
};
thermal-zones {
cpu-thermal0 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&gcc 7>;
coefficients = <1199 0>;
trips {
cpu_alert0: trip0 {
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
cpu_crit0: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
cpu-thermal1 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&gcc 8>;
coefficients = <1132 0>;
trips {
cpu_alert1: trip0 {
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
cpu_crit1: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
cpu-thermal2 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&gcc 9>;
coefficients = <1199 0>;
trips {
cpu_alert2: trip0 {
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
cpu_crit2: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
cpu-thermal3 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&gcc 10>;
coefficients = <1132 0>;
trips {
cpu_alert3: trip0 {
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
cpu_crit3: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
};
cpu-pmu {
compatible = "qcom,krait-pmu";
interrupts = <1 10 0x304>;
};
clocks {
cxo_board: cxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
};
pxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <27000000>;
};
sleep_clk: sleep_clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
};
};
sfpb_mutex: hwmutex {
compatible = "qcom,sfpb-mutex";
syscon = <&sfpb_wrapper_mutex 0x604 0x4>;
#hwlock-cells = <1>;
};
smem {
compatible = "qcom,smem";
memory-region = <&smem_region>;
hwlocks = <&sfpb_mutex 3>;
};
smd {
compatible = "qcom,smd";
modem@0 {
interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 3>;
qcom,smd-edge = <0>;
status = "disabled";
};
q6@1 {
interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 15>;
qcom,smd-edge = <1>;
status = "disabled";
};
dsps@3 {
interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
qcom,smd-edge = <3>;
status = "disabled";
};
riva@6 {
interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 25>;
qcom,smd-edge = <6>;
status = "disabled";
};
};
smsm {
compatible = "qcom,smsm";
#address-cells = <1>;
#size-cells = <0>;
qcom,ipc-1 = <&l2cc 8 4>;
qcom,ipc-2 = <&l2cc 8 14>;
qcom,ipc-3 = <&l2cc 8 23>;
qcom,ipc-4 = <&sps_sic_non_secure 0x4094 0>;
apps_smsm: apps@0 {
reg = <0>;
#qcom,smem-state-cells = <1>;
};
modem_smsm: modem@1 {
reg = <1>;
interrupts = <0 38 IRQ_TYPE_EDGE_RISING>;
interrupt-controller;
#interrupt-cells = <2>;
};
q6_smsm: q6@2 {
reg = <2>;
interrupts = <0 89 IRQ_TYPE_EDGE_RISING>;
interrupt-controller;
#interrupt-cells = <2>;
};
wcnss_smsm: wcnss@3 {
reg = <3>;
interrupts = <0 204 IRQ_TYPE_EDGE_RISING>;
interrupt-controller;
#interrupt-cells = <2>;
};
dsps_smsm: dsps@4 {
reg = <4>;
interrupts = <0 137 IRQ_TYPE_EDGE_RISING>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
firmware {
scm {
compatible = "qcom,scm-apq8064";
clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
clock-names = "core";
};
};
/*
* These channels from the ADC are simply hardware monitors.
* That is why the ADC is referred to as "HKADC" - HouseKeeping
* ADC.
*/
iio-hwmon {
compatible = "iio-hwmon";
io-channels = <&xoadc 0x00 0x01>, /* Battery */
<&xoadc 0x00 0x02>, /* DC in (charger) */
<&xoadc 0x00 0x04>, /* VPH the main system voltage */
<&xoadc 0x00 0x0b>, /* Die temperature */
<&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
<&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
<&xoadc 0x00 0x0e>; /* Charger temperature */
};
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
ranges;
compatible = "simple-bus";
tlmm_pinmux: pinctrl@800000 {
compatible = "qcom,apq8064-pinctrl";
reg = <0x800000 0x4000>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&ps_hold>;
};
sfpb_wrapper_mutex: syscon@1200000 {
compatible = "syscon";
reg = <0x01200000 0x8000>;
};
intc: interrupt-controller@2000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x02000000 0x1000>,
<0x02002000 0x1000>;
};
timer@200a000 {
compatible = "qcom,kpss-timer",
"qcom,kpss-wdt-apq8064", "qcom,msm-timer";
interrupts = <1 1 0x301>,
<1 2 0x301>,
<1 3 0x301>;
reg = <0x0200a000 0x100>;
clock-frequency = <27000000>,
<32768>;
cpu-offset = <0x80000>;
};
acc0: clock-controller@2088000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
};
acc1: clock-controller@2098000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
};
acc2: clock-controller@20a8000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
};
acc3: clock-controller@20b8000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
};
saw0: power-controller@2089000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw1: power-controller@2099000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw2: power-controller@20a9000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw3: power-controller@20b9000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
sps_sic_non_secure: sps-sic-non-secure@12100000 {
compatible = "syscon";
reg = <0x12100000 0x10000>;
};
gsbi1: gsbi@12440000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <1>;
reg = <0x12440000 0x100>;
clocks = <&gcc GSBI1_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
gsbi1_serial: serial@12450000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x12450000 0x100>,
<0x12400000 0x03>;
interrupts = <0 193 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
gsbi1_i2c: i2c@12460000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c1_pins>;
pinctrl-1 = <&i2c1_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x12460000 0x1000>;
interrupts = <0 194 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gsbi2: gsbi@12480000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <2>;
reg = <0x12480000 0x100>;
clocks = <&gcc GSBI2_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
gsbi2_i2c: i2c@124a0000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x124a0000 0x1000>;
pinctrl-0 = <&i2c2_pins>;
pinctrl-1 = <&i2c2_pins_sleep>;
pinctrl-names = "default", "sleep";
interrupts = <0 196 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gsbi3: gsbi@16200000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <3>;
reg = <0x16200000 0x100>;
clocks = <&gcc GSBI3_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi3_i2c: i2c@16280000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c3_pins>;
pinctrl-1 = <&i2c3_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x16280000 0x1000>;
interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI3_QUP_CLK>,
<&gcc GSBI3_H_CLK>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gsbi4: gsbi@16300000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <4>;
reg = <0x16300000 0x03>;
clocks = <&gcc GSBI4_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi4_i2c: i2c@16380000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c4_pins>;
pinctrl-1 = <&i2c4_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x16380000 0x1000>;
interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI4_QUP_CLK>,
<&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
};
gsbi5: gsbi@1a200000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <5>;
reg = <0x1a200000 0x03>;
clocks = <&gcc GSBI5_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi5_serial: serial@1a240000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x1a240000 0x100>,
<0x1a200000 0x03>;
interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
gsbi5_spi: spi@1a280000 {
compatible = "qcom,spi-qup-v1.1.1";
reg = <0x1a280000 0x1000>;
interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-0 = <&spi5_default>;
pinctrl-1 = <&spi5_sleep>;
pinctrl-names = "default", "sleep";
clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi6: gsbi@16500000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <6>;
reg = <0x16500000 0x03>;
clocks = <&gcc GSBI6_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi6_serial: serial@16540000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16540000 0x100>,
<0x16500000 0x03>;
interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
gsbi6_i2c: i2c@16580000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c6_pins>;
pinctrl-1 = <&i2c6_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x16580000 0x1000>;
interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI6_QUP_CLK>,
<&gcc GSBI6_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
};
gsbi7: gsbi@16600000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <7>;
reg = <0x16600000 0x100>;
clocks = <&gcc GSBI7_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
gsbi7_serial: serial@16640000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16640000 0x1000>,
<0x16600000 0x1000>;
interrupts = <0 158 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
gsbi7_i2c: i2c@16680000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c7_pins>;
pinctrl-1 = <&i2c7_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x16680000 0x1000>;
interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI7_QUP_CLK>,
<&gcc GSBI7_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
};
rng@1a500000 {
compatible = "qcom,prng";
reg = <0x1a500000 0x200>;
clocks = <&gcc PRNG_CLK>;
clock-names = "core";
};
ssbi@c00000 {
compatible = "qcom,ssbi";
reg = <0x00c00000 0x1000>;
qcom,controller-type = "pmic-arbiter";
pm8821: pmic@1 {
compatible = "qcom,pm8821";
interrupt-parent = <&tlmm_pinmux>;
interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
#interrupt-cells = <2>;
interrupt-controller;
#address-cells = <1>;
#size-cells = <0>;
pm8821_mpps: mpps@50 {
compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
reg = <0x50>;
interrupts = <24 IRQ_TYPE_NONE>,
<25 IRQ_TYPE_NONE>,
<26 IRQ_TYPE_NONE>,
<27 IRQ_TYPE_NONE>;
gpio-controller;
#gpio-cells = <2>;
};
};
};
qcom,ssbi@500000 {
compatible = "qcom,ssbi";
reg = <0x00500000 0x1000>;
qcom,controller-type = "pmic-arbiter";
pmicintc: pmic@0 {
compatible = "qcom,pm8921";
interrupt-parent = <&tlmm_pinmux>;
interrupts = <74 8>;
#interrupt-cells = <2>;
interrupt-controller;
#address-cells = <1>;
#size-cells = <0>;
pm8921_gpio: gpio@150 {
compatible = "qcom,pm8921-gpio",
"qcom,ssbi-gpio";
reg = <0x150>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
};
pm8921_mpps: mpps@50 {
compatible = "qcom,pm8921-mpp",
"qcom,ssbi-mpp";
reg = <0x50>;
gpio-controller;
#gpio-cells = <2>;
interrupts =
ARM: dts: MSM8064 remove flags from SPMI/MPP IRQs The Qualcomm PMIC GPIO and MPP lines are problematic: the are fetched from the main MFD driver with platform_get_irq() which means that at this point they will all be assigned the flags set up for the interrupts in the device tree. That is problematic since these are flagged as rising edge and an this point the interrupt descriptor is assigned a rising edge, while the only thing the GPIO/MPP drivers really do is issue irq_get_irqchip_state() on the line to read it out and to provide a .to_irq() helper for *other* IRQ consumers. If another device tree node tries to flag the same IRQ for use as something else than rising edge, the kernel irqdomain core will protest like this: type mismatch, failed to map hwirq-NN for <FOO>! Which is what happens when the device tree defines two contradictory flags for the same interrupt line. To work around this and alleviate the problem, assign 0 as flag for the interrupts taken by the PM GPIO and MPP drivers. This will lead to the flag being unset, and a second consumer requesting rising, falling, both or level interrupts will be respected. This is what the qcom-pm*.dtsi files already do. Switched to using the symbolic name IRQ_TYPE_NONE so that we get this more readable. Cc: stable@vger.kernel.org Fixes: bce360469676 ("ARM: dts: apq8064: add pm8921 mpp support") Fixes: 874443fe9e33 ("ARM: dts: apq8064: Add pm8921 mfd and its gpio node") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Björn Andersson <bjorn.andersson@linaro.org> Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Andy Gross <andy.gross@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2016-08-05 16:38:37 +08:00
<128 IRQ_TYPE_NONE>,
<129 IRQ_TYPE_NONE>,
<130 IRQ_TYPE_NONE>,
<131 IRQ_TYPE_NONE>,
<132 IRQ_TYPE_NONE>,
<133 IRQ_TYPE_NONE>,
<134 IRQ_TYPE_NONE>,
<135 IRQ_TYPE_NONE>,
<136 IRQ_TYPE_NONE>,
<137 IRQ_TYPE_NONE>,
<138 IRQ_TYPE_NONE>,
<139 IRQ_TYPE_NONE>;
};
rtc@11d {
compatible = "qcom,pm8921-rtc";
interrupt-parent = <&pmicintc>;
interrupts = <39 1>;
reg = <0x11d>;
allow-set-time;
};
pwrkey@1c {
compatible = "qcom,pm8921-pwrkey";
reg = <0x1c>;
interrupt-parent = <&pmicintc>;
interrupts = <50 1>, <51 1>;
debounce = <15625>;
pull-up;
};
xoadc: xoadc@197 {
compatible = "qcom,pm8921-adc";
reg = <197>;
interrupts-extended = <&pmicintc 78 IRQ_TYPE_EDGE_RISING>;
#address-cells = <2>;
#size-cells = <0>;
#io-channel-cells = <2>;
vcoin: adc-channel@00 {
reg = <0x00 0x00>;
};
vbat: adc-channel@01 {
reg = <0x00 0x01>;
};
dcin: adc-channel@02 {
reg = <0x00 0x02>;
};
vph_pwr: adc-channel@04 {
reg = <0x00 0x04>;
};
batt_therm: adc-channel@08 {
reg = <0x00 0x08>;
};
batt_id: adc-channel@09 {
reg = <0x00 0x09>;
};
usb_vbus: adc-channel@0a {
reg = <0x00 0x0a>;
};
die_temp: adc-channel@0b {
reg = <0x00 0x0b>;
};
ref_625mv: adc-channel@0c {
reg = <0x00 0x0c>;
};
ref_1250mv: adc-channel@0d {
reg = <0x00 0x0d>;
};
chg_temp: adc-channel@0e {
reg = <0x00 0x0e>;
};
ref_muxoff: adc-channel@0f {
reg = <0x00 0x0f>;
};
};
};
};
qfprom: qfprom@700000 {
compatible = "qcom,qfprom";
reg = <0x00700000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
tsens_calib: calib {
reg = <0x404 0x10>;
};
tsens_backup: backup_calib {
reg = <0x414 0x10>;
};
};
gcc: clock-controller@900000 {
compatible = "qcom,gcc-apq8064";
reg = <0x00900000 0x4000>;
nvmem-cells = <&tsens_calib>, <&tsens_backup>;
nvmem-cell-names = "calib", "calib_backup";
#clock-cells = <1>;
#reset-cells = <1>;
#thermal-sensor-cells = <1>;
};
lcc: clock-controller@28000000 {
compatible = "qcom,lcc-apq8064";
reg = <0x28000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
mmcc: clock-controller@4000000 {
compatible = "qcom,mmcc-apq8064";
reg = <0x4000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
l2cc: clock-controller@2011000 {
compatible = "syscon";
reg = <0x2011000 0x1000>;
};
rpm@108000 {
compatible = "qcom,rpm-apq8064";
reg = <0x108000 0x1000>;
qcom,ipc = <&l2cc 0x8 2>;
interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "ack", "err", "wakeup";
rpmcc: clock-controller {
compatible = "qcom,rpmcc-apq8064", "qcom,rpmcc";
#clock-cells = <1>;
};
regulators {
compatible = "qcom,rpm-pm8921-regulators";
pm8921_s1: s1 {};
pm8921_s2: s2 {};
pm8921_s3: s3 {};
pm8921_s4: s4 {};
pm8921_s7: s7 {};
pm8921_s8: s8 {};
pm8921_l1: l1 {};
pm8921_l2: l2 {};
pm8921_l3: l3 {};
pm8921_l4: l4 {};
pm8921_l5: l5 {};
pm8921_l6: l6 {};
pm8921_l7: l7 {};
pm8921_l8: l8 {};
pm8921_l9: l9 {};
pm8921_l10: l10 {};
pm8921_l11: l11 {};
pm8921_l12: l12 {};
pm8921_l14: l14 {};
pm8921_l15: l15 {};
pm8921_l16: l16 {};
pm8921_l17: l17 {};
pm8921_l18: l18 {};
pm8921_l21: l21 {};
pm8921_l22: l22 {};
pm8921_l23: l23 {};
pm8921_l24: l24 {};
pm8921_l25: l25 {};
pm8921_l26: l26 {};
pm8921_l27: l27 {};
pm8921_l28: l28 {};
pm8921_l29: l29 {};
pm8921_lvs1: lvs1 {};
pm8921_lvs2: lvs2 {};
pm8921_lvs3: lvs3 {};
pm8921_lvs4: lvs4 {};
pm8921_lvs5: lvs5 {};
pm8921_lvs6: lvs6 {};
pm8921_lvs7: lvs7 {};
pm8921_usb_switch: usb-switch {};
pm8921_hdmi_switch: hdmi-switch {
bias-pull-down;
};
pm8921_ncp: ncp {};
};
};
usb1: usb@12500000 {
compatible = "qcom,ci-hdrc";
reg = <0x12500000 0x200>,
<0x12500200 0x200>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
clock-names = "core", "iface";
assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
assigned-clock-rates = <60000000>;
resets = <&gcc USB_HS1_RESET>;
reset-names = "core";
phy_type = "ulpi";
ahb-burst-config = <0>;
phys = <&usb_hs1_phy>;
phy-names = "usb-phy";
status = "disabled";
#reset-cells = <1>;
ulpi {
usb_hs1_phy: phy {
compatible = "qcom,usb-hs-phy-apq8064",
"qcom,usb-hs-phy";
clocks = <&sleep_clk>, <&cxo_board>;
clock-names = "sleep", "ref";
resets = <&usb1 0>;
reset-names = "por";
#phy-cells = <0>;
};
};
};
usb3: usb@12520000 {
compatible = "qcom,ci-hdrc";
reg = <0x12520000 0x200>,
<0x12520200 0x200>;
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>;
clock-names = "core", "iface";
assigned-clocks = <&gcc USB_HS3_XCVR_CLK>;
assigned-clock-rates = <60000000>;
resets = <&gcc USB_HS3_RESET>;
reset-names = "core";
phy_type = "ulpi";
ahb-burst-config = <0>;
phys = <&usb_hs3_phy>;
phy-names = "usb-phy";
status = "disabled";
#reset-cells = <1>;
ulpi {
usb_hs3_phy: phy {
compatible = "qcom,usb-hs-phy-apq8064",
"qcom,usb-hs-phy";
#phy-cells = <0>;
clocks = <&sleep_clk>, <&cxo_board>;
clock-names = "sleep", "ref";
resets = <&usb3 0>;
reset-names = "por";
};
};
};
usb4: usb@12530000 {
compatible = "qcom,ci-hdrc";
reg = <0x12530000 0x200>,
<0x12530200 0x200>;
interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>;
clock-names = "core", "iface";
assigned-clocks = <&gcc USB_HS4_XCVR_CLK>;
assigned-clock-rates = <60000000>;
resets = <&gcc USB_HS4_RESET>;
reset-names = "core";
phy_type = "ulpi";
ahb-burst-config = <0>;
phys = <&usb_hs4_phy>;
phy-names = "usb-phy";
status = "disabled";
#reset-cells = <1>;
ulpi {
usb_hs4_phy: phy {
compatible = "qcom,usb-hs-phy-apq8064",
"qcom,usb-hs-phy";
#phy-cells = <0>;
clocks = <&sleep_clk>, <&cxo_board>;
clock-names = "sleep", "ref";
resets = <&usb4 0>;
reset-names = "por";
};
};
};
sata_phy0: phy@1b400000 {
compatible = "qcom,apq8064-sata-phy";
status = "disabled";
reg = <0x1b400000 0x200>;
reg-names = "phy_mem";
clocks = <&gcc SATA_PHY_CFG_CLK>;
clock-names = "cfg";
#phy-cells = <0>;
};
sata0: sata@29000000 {
compatible = "qcom,apq8064-ahci", "generic-ahci";
status = "disabled";
reg = <0x29000000 0x180>;
interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc SFAB_SATA_S_H_CLK>,
<&gcc SATA_H_CLK>,
<&gcc SATA_A_CLK>,
<&gcc SATA_RXOOB_CLK>,
<&gcc SATA_PMALIVE_CLK>;
clock-names = "slave_iface",
"iface",
"bus",
"rxoob",
"core_pmalive";
assigned-clocks = <&gcc SATA_RXOOB_CLK>,
<&gcc SATA_PMALIVE_CLK>;
assigned-clock-rates = <100000000>, <100000000>;
phys = <&sata_phy0>;
phy-names = "sata-phy";
ports-implemented = <0x1>;
};
/* Temporary fixed regulator */
sdcc1bam:dma@12402000{
compatible = "qcom,bam-v1.3.0";
reg = <0x12402000 0x8000>;
interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc SDC1_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
sdcc3bam:dma@12182000{
compatible = "qcom,bam-v1.3.0";
reg = <0x12182000 0x8000>;
interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc SDC3_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
sdcc4bam:dma@121c2000{
compatible = "qcom,bam-v1.3.0";
reg = <0x121c2000 0x8000>;
interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc SDC4_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
amba {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
sdcc1: sdcc@12400000 {
status = "disabled";
compatible = "arm,pl18x", "arm,primecell";
pinctrl-names = "default";
pinctrl-0 = <&sdcc1_pins>;
arm,primecell-periphid = <0x00051180>;
reg = <0x12400000 0x2000>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <8>;
max-frequency = <96000000>;
non-removable;
cap-sd-highspeed;
cap-mmc-highspeed;
dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
dma-names = "tx", "rx";
};
sdcc3: sdcc@12180000 {
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
status = "disabled";
reg = <0x12180000 0x2000>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <4>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <192000000>;
no-1-8-v;
dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
dma-names = "tx", "rx";
};
sdcc4: sdcc@121c0000 {
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
status = "disabled";
reg = <0x121c0000 0x2000>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <4>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <48000000>;
dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&sdc4_gpios>;
};
};
tcsr: syscon@1a400000 {
compatible = "qcom,tcsr-apq8064", "syscon";
reg = <0x1a400000 0x100>;
};
gpu: adreno-3xx@4300000 {
compatible = "qcom,adreno-3xx";
reg = <0x04300000 0x20000>;
reg-names = "kgsl_3d0_reg_memory";
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "kgsl_3d0_irq";
clock-names =
"core_clk",
"iface_clk",
"mem_clk",
"mem_iface_clk";
clocks =
<&mmcc GFX3D_CLK>,
<&mmcc GFX3D_AHB_CLK>,
<&mmcc GFX3D_AXI_CLK>,
<&mmcc MMSS_IMEM_AHB_CLK>;
qcom,chipid = <0x03020002>;
iommus = <&gfx3d 0
&gfx3d 1
&gfx3d 2
&gfx3d 3
&gfx3d 4
&gfx3d 5
&gfx3d 6
&gfx3d 7
&gfx3d 8
&gfx3d 9
&gfx3d 10
&gfx3d 11
&gfx3d 12
&gfx3d 13
&gfx3d 14
&gfx3d 15
&gfx3d 16
&gfx3d 17
&gfx3d 18
&gfx3d 19
&gfx3d 20
&gfx3d 21
&gfx3d 22
&gfx3d 23
&gfx3d 24
&gfx3d 25
&gfx3d 26
&gfx3d 27
&gfx3d 28
&gfx3d 29
&gfx3d 30
&gfx3d 31
&gfx3d1 0
&gfx3d1 1
&gfx3d1 2
&gfx3d1 3
&gfx3d1 4
&gfx3d1 5
&gfx3d1 6
&gfx3d1 7
&gfx3d1 8
&gfx3d1 9
&gfx3d1 10
&gfx3d1 11
&gfx3d1 12
&gfx3d1 13
&gfx3d1 14
&gfx3d1 15
&gfx3d1 16
&gfx3d1 17
&gfx3d1 18
&gfx3d1 19
&gfx3d1 20
&gfx3d1 21
&gfx3d1 22
&gfx3d1 23
&gfx3d1 24
&gfx3d1 25
&gfx3d1 26
&gfx3d1 27
&gfx3d1 28
&gfx3d1 29
&gfx3d1 30
&gfx3d1 31>;
qcom,gpu-pwrlevels {
compatible = "qcom,gpu-pwrlevels";
qcom,gpu-pwrlevel@0 {
qcom,gpu-freq = <450000000>;
};
qcom,gpu-pwrlevel@1 {
qcom,gpu-freq = <27000000>;
};
};
};
mmss_sfpb: syscon@5700000 {
compatible = "syscon";
reg = <0x5700000 0x70>;
};
dsi0: mdss_dsi@4700000 {
compatible = "qcom,mdss-dsi-ctrl";
label = "MDSS DSI CTRL->0";
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x04700000 0x200>;
reg-names = "dsi_ctrl";
clocks = <&mmcc DSI_M_AHB_CLK>,
<&mmcc DSI_S_AHB_CLK>,
<&mmcc AMP_AHB_CLK>,
<&mmcc DSI_CLK>,
<&mmcc DSI1_BYTE_CLK>,
<&mmcc DSI_PIXEL_CLK>,
<&mmcc DSI1_ESC_CLK>;
clock-names = "iface_clk", "bus_clk", "core_mmss_clk",
"src_clk", "byte_clk", "pixel_clk",
"core_clk";
assigned-clocks = <&mmcc DSI1_BYTE_SRC>,
<&mmcc DSI1_ESC_SRC>,
<&mmcc DSI_SRC>,
<&mmcc DSI_PIXEL_SRC>;
assigned-clock-parents = <&dsi0_phy 0>,
<&dsi0_phy 0>,
<&dsi0_phy 1>,
<&dsi0_phy 1>;
syscon-sfpb = <&mmss_sfpb>;
phys = <&dsi0_phy>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
dsi0_in: endpoint {
};
};
port@1 {
reg = <1>;
dsi0_out: endpoint {
};
};
};
};
dsi0_phy: dsi-phy@4700200 {
compatible = "qcom,dsi-phy-28nm-8960";
#clock-cells = <1>;
#phy-cells = <0>;
reg = <0x04700200 0x100>,
<0x04700300 0x200>,
<0x04700500 0x5c>;
reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
clock-names = "iface_clk";
clocks = <&mmcc DSI_M_AHB_CLK>;
};
mdp_port0: iommu@7500000 {
compatible = "qcom,apq8064-iommu";
#iommu-cells = <1>;
clock-names =
"smmu_pclk",
"iommu_clk";
clocks =
<&mmcc SMMU_AHB_CLK>,
<&mmcc MDP_AXI_CLK>;
reg = <0x07500000 0x100000>;
interrupts =
<GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
qcom,ncb = <2>;
};
mdp_port1: iommu@7600000 {
compatible = "qcom,apq8064-iommu";
#iommu-cells = <1>;
clock-names =
"smmu_pclk",
"iommu_clk";
clocks =
<&mmcc SMMU_AHB_CLK>,
<&mmcc MDP_AXI_CLK>;
reg = <0x07600000 0x100000>;
interrupts =
<GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
qcom,ncb = <2>;
};
gfx3d: iommu@7c00000 {
compatible = "qcom,apq8064-iommu";
#iommu-cells = <1>;
clock-names =
"smmu_pclk",
"iommu_clk";
clocks =
<&mmcc SMMU_AHB_CLK>,
<&mmcc GFX3D_AXI_CLK>;
reg = <0x07c00000 0x100000>;
interrupts =
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
qcom,ncb = <3>;
};
gfx3d1: iommu@7d00000 {
compatible = "qcom,apq8064-iommu";
#iommu-cells = <1>;
clock-names =
"smmu_pclk",
"iommu_clk";
clocks =
<&mmcc SMMU_AHB_CLK>,
<&mmcc GFX3D_AXI_CLK>;
reg = <0x07d00000 0x100000>;
interrupts =
<GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>;
qcom,ncb = <3>;
};
pcie: pci@1b500000 {
compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
reg = <0x1b500000 0x1000
0x1b502000 0x80
0x1b600000 0x100
0x0ff00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000 /* I/O */
2018-05-09 20:01:34 +08:00
0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* memory */
interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc PCIE_A_CLK>,
<&gcc PCIE_H_CLK>,
<&gcc PCIE_PHY_REF_CLK>;
clock-names = "core", "iface", "phy";
resets = <&gcc PCIE_ACLK_RESET>,
<&gcc PCIE_HCLK_RESET>,
<&gcc PCIE_POR_RESET>,
<&gcc PCIE_PCI_RESET>,
<&gcc PCIE_PHY_RESET>;
reset-names = "axi", "ahb", "por", "pci", "phy";
status = "disabled";
};
hdmi: hdmi-tx@4a00000 {
compatible = "qcom,hdmi-tx-8960";
pinctrl-names = "default";
pinctrl-0 = <&hdmi_pinctrl>;
reg = <0x04a00000 0x2f0>;
reg-names = "core_physical";
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mmcc HDMI_APP_CLK>,
<&mmcc HDMI_M_AHB_CLK>,
<&mmcc HDMI_S_AHB_CLK>;
clock-names = "core_clk",
"master_iface_clk",
"slave_iface_clk";
phys = <&hdmi_phy>;
phy-names = "hdmi-phy";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
hdmi_in: endpoint {
};
};
port@1 {
reg = <1>;
hdmi_out: endpoint {
};
};
};
};
hdmi_phy: hdmi-phy@4a00400 {
compatible = "qcom,hdmi-phy-8960";
reg = <0x4a00400 0x60>,
<0x4a00500 0x100>;
reg-names = "hdmi_phy",
"hdmi_pll";
clocks = <&mmcc HDMI_S_AHB_CLK>;
clock-names = "slave_iface_clk";
#phy-cells = <0>;
};
mdp: mdp@5100000 {
compatible = "qcom,mdp4";
reg = <0x05100000 0xf0000>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mmcc MDP_CLK>,
<&mmcc MDP_AHB_CLK>,
<&mmcc MDP_AXI_CLK>,
<&mmcc MDP_LUT_CLK>,
<&mmcc HDMI_TV_CLK>,
<&mmcc MDP_TV_CLK>;
clock-names = "core_clk",
"iface_clk",
"bus_clk",
"lut_clk",
"hdmi_clk",
"tv_clk";
iommus = <&mdp_port0 0
&mdp_port0 2
&mdp_port1 0
&mdp_port1 2>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
mdp_lvds_out: endpoint {
};
};
port@1 {
reg = <1>;
mdp_dsi1_out: endpoint {
};
};
port@2 {
reg = <2>;
mdp_dsi2_out: endpoint {
};
};
port@3 {
reg = <3>;
mdp_dtv_out: endpoint {
};
};
};
};
riva: riva-pil@3204000 {
compatible = "qcom,riva-pil";
reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>;
reg-names = "ccu", "dxe", "pmu";
interrupts-extended = <&intc GIC_SPI 199 IRQ_TYPE_EDGE_RISING>,
<&wcnss_smsm 6 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal";
memory-region = <&wcnss_mem>;
vddcx-supply = <&pm8921_s3>;
vddmx-supply = <&pm8921_l24>;
vddpx-supply = <&pm8921_s4>;
status = "disabled";
iris {
compatible = "qcom,wcn3660";
clocks = <&cxo_board>;
clock-names = "xo";
vddxo-supply = <&pm8921_l4>;
vddrfa-supply = <&pm8921_s2>;
vddpa-supply = <&pm8921_l10>;
vdddig-supply = <&pm8921_lvs2>;
};
smd-edge {
interrupts = <GIC_SPI 198 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 25>;
qcom,smd-edge = <6>;
label = "riva";
wcnss {
compatible = "qcom,wcnss";
qcom,smd-channels = "WCNSS_CTRL";
qcom,mmio = <&riva>;
bt {
compatible = "qcom,wcnss-bt";
};
wifi {
compatible = "qcom,wcnss-wlan";
interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "tx", "rx";
qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
qcom,smem-state-names = "tx-enable", "tx-rings-empty";
};
};
};
};
etb@1a01000 {
compatible = "coresight-etb10", "arm,primecell";
reg = <0x1a01000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
in-ports {
port {
etb_in: endpoint {
remote-endpoint = <&replicator_out0>;
};
};
};
};
tpiu@1a03000 {
compatible = "arm,coresight-tpiu", "arm,primecell";
reg = <0x1a03000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
in-ports {
port {
tpiu_in: endpoint {
remote-endpoint = <&replicator_out1>;
};
};
};
};
replicator {
compatible = "arm,coresight-replicator";
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
out-ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
replicator_out0: endpoint {
remote-endpoint = <&etb_in>;
};
};
port@1 {
reg = <1>;
replicator_out1: endpoint {
remote-endpoint = <&tpiu_in>;
};
};
};
in-ports {
port {
replicator_in: endpoint {
remote-endpoint = <&funnel_out>;
};
};
};
};
funnel@1a04000 {
compatible = "arm,coresight-funnel", "arm,primecell";
reg = <0x1a04000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
in-ports {
#address-cells = <1>;
#size-cells = <0>;
/*
* Not described input ports:
* 2 - connected to STM component
* 3 - not-connected
* 6 - not-connected
* 7 - not-connected
*/
port@0 {
reg = <0>;
funnel_in0: endpoint {
remote-endpoint = <&etm0_out>;
};
};
port@1 {
reg = <1>;
funnel_in1: endpoint {
remote-endpoint = <&etm1_out>;
};
};
port@4 {
reg = <4>;
funnel_in4: endpoint {
remote-endpoint = <&etm2_out>;
};
};
port@5 {
reg = <5>;
funnel_in5: endpoint {
remote-endpoint = <&etm3_out>;
};
};
};
out-ports {
port {
funnel_out: endpoint {
remote-endpoint = <&replicator_in>;
};
};
};
};
etm@1a1c000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x1a1c000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
cpu = <&CPU0>;
out-ports {
port {
etm0_out: endpoint {
remote-endpoint = <&funnel_in0>;
};
};
};
};
etm@1a1d000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x1a1d000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
cpu = <&CPU1>;
out-ports {
port {
etm1_out: endpoint {
remote-endpoint = <&funnel_in1>;
};
};
};
};
etm@1a1e000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x1a1e000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
cpu = <&CPU2>;
out-ports {
port {
etm2_out: endpoint {
remote-endpoint = <&funnel_in4>;
};
};
};
};
etm@1a1f000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x1a1f000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
cpu = <&CPU3>;
out-ports {
port {
etm3_out: endpoint {
remote-endpoint = <&funnel_in5>;
};
};
};
};
};
};
#include "qcom-apq8064-pins.dtsi"