linux/net/mpls/Makefile

#
# Makefile for MPLS.
#
obj-$(CONFIG_NET_MPLS_GSO) += mpls_gso.o
obj-$(CONFIG_MPLS_ROUTING) += mpls_router.o
obj-$(CONFIG_MPLS_IPTUNNEL) += mpls_iptunnel.o

mpls_router-y := af_mpls.o
MPLS: Add limited GSO support In the case where a non-MPLS packet is received and an MPLS stack is added it may well be the case that the original skb is GSO but the NIC used for transmit does not support GSO of MPLS packets. The aim of this code is to provide GSO in software for MPLS packets whose skbs are GSO. SKB Usage: When an implementation adds an MPLS stack to a non-MPLS packet it should do the following to skb metadata: * Set skb->inner_protocol to the old non-MPLS ethertype of the packet. skb->inner_protocol is added by this patch. * Set skb->protocol to the new MPLS ethertype of the packet. * Set skb->network_header to correspond to the end of the L3 header, including the MPLS label stack. I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to kernel" which adds MPLS support to the kernel datapath of Open vSwtich. That patch sets the above requirements in datapath/actions.c:push_mpls() and was used to exercise this code. The datapath patch is against the Open vSwtich tree but it is intended that it be added to the Open vSwtich code present in the mainline Linux kernel at some point. Features: I believe that the approach that I have taken is at least partially consistent with the handling of other protocols. Jesse, I understand that you have some ideas here. I am more than happy to change my implementation. This patch adds dev->mpls_features which may be used by devices to advertise features supported for MPLS packets. A new NETIF_F_MPLS_GSO feature is added for devices which support hardware MPLS GSO offload. Currently no devices support this and MPLS GSO always falls back to software. Alternate Implementation: One possible alternate implementation is to teach netif_skb_features() and skb_network_protocol() about MPLS, in a similar way to their understanding of VLANs. I believe this would avoid the need for net/mpls/mpls_gso.c and in particular the calls to __skb_push() and __skb_push() in mpls_gso_segment(). I have decided on the implementation in this patch as it should not introduce any overhead in the case where mpls_gso is not compiled into the kernel or inserted as a module. MPLS GSO suggested by Jesse Gross. Based in part on "v4 GRE: Add TCP segmentation offload for GRE" by Pravin B Shelar. Cc: Jesse Gross <jesse@nicira.com> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net> 2013-05-24 05:02:52 +08:00			`#`
			`# Makefile for MPLS.`
			`#`
mpls: Allow mpls_gso to be built as module Kconfig already allows mpls to be built as module. Following patch fixes Makefile to do same. CC: Simon Horman <simon.horman@netronome.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> 2014-10-30 15:50:04 +08:00			`obj-$(CONFIG_NET_MPLS_GSO) += mpls_gso.o`
mpls: Allow mpls_gso and mpls_router to be built as modules CONFIG_MPLS=m doesn't result in a kernel module being built because it applies to the net/mpls directory, rather than to .o files. So revert the MPLS menuitem to being a boolean and make MPLS_GSO and MPLS_ROUTING tristates to allow mpls_gso and mpls_router modules to be produced as desired. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net> 2015-03-11 00:37:59 +08:00			`obj-$(CONFIG_MPLS_ROUTING) += mpls_router.o`
mpls: ip tunnel support This implementation uses lwtunnel infrastructure to register hooks for mpls tunnel encaps. It picks cues from iptunnel_encaps infrastructure and previous mpls iptunnel RFC patches from Eric W. Biederman and Robert Shearman Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> 2015-07-21 16:43:53 +08:00			`obj-$(CONFIG_MPLS_IPTUNNEL) += mpls_iptunnel.o`
mpls: Allow mpls_gso and mpls_router to be built as modules CONFIG_MPLS=m doesn't result in a kernel module being built because it applies to the net/mpls directory, rather than to .o files. So revert the MPLS menuitem to being a boolean and make MPLS_GSO and MPLS_ROUTING tristates to allow mpls_gso and mpls_router modules to be produced as desired. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net> 2015-03-11 00:37:59 +08:00
			`mpls_router-y := af_mpls.o`